Aiwa NSX-VC58

NSX-VC58
HR, HT
SERVICE MANUAL
BASIC TAPE MECHANISM : 2ZM-3MK2 PR4NM

BASIC CD MECHANISM : AZG-1 VZD3RDM /
AZG-1 VZD3RNDM
COMPACT DISC
STEREO SYSTEM
SYSTEM
NSX-VC58
CD
CASSEIVER
CX-NVC58
SYSTEM
NSX-VC58 <HR>
NSX-VC58 <HT>
SPEAKER
SX-WNBL53
TAPE MECHANISM
2ZM-3MK2 PR4NM
REMOTE
CONTROLLER
RC-ZAS07
CD MECHANISM
AZG-1 VZD3RDM
AZG-1 VZD3RNDM
This Service Manual is the Revision Publishing and replaces Simple

Manual NSX-VC58 (HR), (S/M Code No. 09-003-432-0T1).
S/M Code No. 09-006-432-0R1
RE
VI
SIO
DA
N
TA
If requiring information about the CD mechanism, see Service Manual

of AZG-1, (S/M Code No. 09-001-335-3NG).
SPECIFICATIONS
<FM tuner section>
Tuning range
Usable sensitivity (IHF)
Antenna terminals
<MW tuner section>
Tuning range
87.5 MHz to 108 MHz

13.2 dBf
75 ohms (unbalanced)
Usable sensitivity
Antenna
531 kHz to 1602 kHz (9 kHz step)

530 kHz to 1710 kHz (10 kHz step)
350 V/m
Loop antenna
<SW tuner section>

Tuning range
Antenna
5.730 MHz to 17.900 MHz

Wire antenna
<Amplifier section>
Mid-high frequency amplifier
Power output
Rated: 20 W + 20 W (8 ohms, THD 1%,
1 kHz)
Reference: 25 W + 25 W (8 ohms,
THD 10%, 1 kHz)
Total harmonic distortion 0.1% (10 W, 1 kHz, 8 ohms,
DIN AUDIO)
Low frequency amplifier
Power output
Rated: 60 W + 60 W (6 ohms, THD 1%,
130 Hz)
Reference: 75 W + 75 W (6 ohms,
THD 10%, 130 kHz)
Total harmonic distortion 0.1% (30 W, 130 Hz, 6 ohms,
DIN AUDIO)
Inputs
VIDEO/AUX: 300 mV (adjustable)
MIC: 1.0 mV (10 K ohms)
Outputs
SPEAKERS HIGH FREQ:
accept speakers of 8 ohms or more
SPEAKERS LOW FREQ:
accept speakers of 6 ohms or more
SURROUND SPEAKERS:
accept speakers of 8 ohms to 16 ohms
VIDEO OUT: 1.0 Vp-p (75 ohms)
PHONES (stereo jack): accepts
headphones of 32 ohms or more
<Cassette deck section>
Track format
Frequency response
Recording system
Heads
4 tracks, 2 channels stereo

50 Hz 15000 Hz
AC bias
Deck 1 : Playback head x 1
Deck 2 : Recording/Playback head x 1,
erase head x 1
<Compact disc player section>

Laser
Semiconductor laser ( =780 nm)
D-A converter
1 bit dual
Signal-to-noise ratio
85 dB (1 kHz, 0 dB)
Harmonic distortion
0.05 % (1 kHz, 0 dB)
Video signal
NTSC/PAL color format (selectable)
Video data
MPEG 1
Audio data
MPEG 1, LAYER 2
<Speaker system SX-WNBL53>
Speaker system
3 way, Built-in subwoofer (magnetic
shielded type)
Speaker units
Subwoofer:
160 mm cone type
Full range:
100mm cone type
Super tweeter:
20 mm ceramic type
Impedance
6 ohms/8 ohms
Output sound pressure level 87 dB/W/m
Dimensions (W x H x D)
230 x 324 x 282 mm
Weight
4.8 kg
<General>
Power requirements
120 V/220-230 V/240 V AC

switchable, 50/60 Hz
Power consumption
170 W
Power consumption in standby mode
If the power-economizing mode is
ECO OFF: 20 W
if the power-economizing mode is
ECO ON or ECO AUTO: 0.9 W
Dimensions of main unit
260 x 326 x 346 mm
(W x H x D)
Weight of main unit
10.0 kg
Design and specifications are subject to change without notice.

The word "BBE"and the "BBE symbol" are trademarks of BBE
Sound, Inc.
Under license from BBE Sound,Inc.
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING

This set employs laser. Therefore, be sure to follow carefully
the instructions below when servicing.
WARNING!!
WHEN SERVICING, DO NOT APPROACH THE LASER
EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS
NECESSARY TO CONFIRM LASER BEAM EMISSION.
BE SURE TO OBSERVE FROM A DISTANCE OF MORE
THAN 30cm FROM THE SURFACE OF THE OBJECTIVE LENS ON THE OPTICAL PICK-UP BLOCK.
CAUTION
Use of controls or adjustments or performance of procedures other than those specified herin may result in
hazardous radiation exposure.
ATTENTION
Lutillisation de commandes, rglages ou procdures
autres que ceux spcifis peut entraner une dangereuse
exposition aux radiations.
ADVARSEL
s
Caution: Invisible laser radiation when

open and interlocks defeated avoid
exposure to beam.
Advarsel: Usynlig laserstling ved bning,
nr sikkerhedsafbrydere er ude af funktion.
Undg udsttelse for strling.
Usynlig laserstling ved bning, nr sikkerhedsafbrydereer

ude af funktion. Undg udsttelse for strling.
This Compact Disc player is classified as a CLASS 1
LASER product.
The CLASS 1 LASER PRODUCT label is located on the
rear exterior.
VAROITUS!
Laiteen Kyttminen muulla kuin tss kyttohjeessa
mainitulla tavalla saataa altistaa kyt-tjn
turvallisuusluokan 1 ylittvlle nkymttmlle
lasersteilylle.
CLASS 1
KLASSE 1
LUOKAN 1
KLASS 1
VARNING!
Om apparaten anvnds p annat stt n vad som
specificeras i denna bruksanvising, kan anvndaren
utsttas fr osynling laserstrlning, som verskrider
grnsen fr laserklass 1.
LASER PRODUCT
LASER PRODUKT
LASER LAITE
LASER APPARAT
Precaution to replace Optical block
(KSS-213F)
PICK-UP Assy P.C.B
Body or clothes electrostatic potential could
ruin laser diode in the optical block. Be sure
ground body and workbench, and use care the
clothes do not touch the diode.
1) After the connection, remove solder shown in

right figure.
Solder
NOTE ON BEFORE STARTING REPAIR

1. Forced discharge of electrolytic capacitor of power supply block
When repair is going to be attempted in the set that uses relay circuit in the power supply block, electric potential is kept charged across
the electrolytic capacitors (C101, 102) even though AC power cord is removed. If repair is attempted in this condition, secondary defect
can occur.
In order to prevent the secondary trouble, perform the following measures before starting repair work.
Discharge procedure
MAIN C.B
1 Remove the AC power cord.

2 Connect a discharging resistor at an end of lead wire that
has clips at both ends. Connect the other end of the lead
wire to metal chassis.
3 Contact the other end of the discharging resistor to the
positive (+) side (+VH) of C101. (For two seconds)
4 Contact the same end of the discharging resistor as step
3 to the negative (-) side (-VH) of C102 in the same way.
(For two seconds)
5 Check that voltage across C101 and C102 has decreased
to 1 V or less using a multimeter or an oscilloscope.
D101
Select a discharging resistor referring to the following table.
C102
Fig-1
Charging voltage (V)
Discharging
(C101, 102)
resistor ()
25-48
100
87-A00-247-090
49-140
220
87-A00-232-090
Rated power (W)
C101
Parts number
Note: The reference numbers (C101, C102) of the electrolytic capacitors can change depending on the models. Be sure to check the
reference numbers of the charging capacitors on schematic diagram before starting the discharging work.
2. Check items before exchanging the MICROCOMPUTER

Be sure to check the following items before exchanging the MICROCOMPUTER. Exchange the MICROCOMPUTER after confirming
that the MICROCOMPUTER is surely defective.
2-1. Regarding the HOLD terminal of the MICROCOMPUTER

When the HOLD terminal (INPUT) of the MICROCOMPUTER is H, the MICROCOMPUTER is judged to be operating correctly.
When this terminal is L, the main power cannot be turned on. Therefore, be sure to check the terminal voltage of the HOLD
terminal before exchange.
When the MICROCOMPUTER is not defective, the HOLD terminal can also go L when the POWER AMPLIFIER has any
abnormalities that triggers the abnormality detection circuit on the MAIN C. B. that sets the HOLD terminal to L.
Good or no good judgement of the MICROCOMPUTER

1 Turn on the AC main power.
2 Confirm that the main power is turned on and the HOLD terminal of the MICROCOMPUTER keeps the H level or not.
3 When the HOLD terminal is L level, the abnormality detection circuit is judged to be working correctly and the
MICROCOMPUTER is judged to be good.
In such a case, check also if the POWER AMPLIFIER circuit or power supply circuit has any abnormalities or not.
2-2. Regarding reset
TE
R
There are cases that the machine does not work correctly because the MICROCOMPUTER is not reset even though the AC power
cord is re-inserted, or the software reset (pressing the STOP key + POWER key) is performed.
When the above described phenomenon occurs, it can lead to wrong judgement as if the MICROCOMPUTER is defective and to
exchange the MICROCOMPUTER. In such a case, perform the forced-reset by the following procedure and check good or no
good of the MICROCOMPUTER.
1 Remove the AC power cord.
IC
RO
CO
PU
FRONT C.B
18
15
C113
% VSS
MICROC113
COMPUTER
* VDD
FRONT C.B
Short with tweezers.
Fig-2-2
2 Short both ends of the electrolytic capacitor C113 that is connected to VDD of the MICROCOMPUTER with tweezers.
3 Connect the AC power cord again. If the MICROCOMPUTER returns to the normal operation, the MICROCOMPUTER is
good.
Note: The reference number or MICROCOMPUTER pin number of transistor (Q110) and electrolytic capacitor (C113) can change depending
on the models. Be sure to check the reference numbers on schematic diagram before starting the discharging work.
2-3. Confirmation of soldering state of MICROCOMPUTER

Check the soldering state of the MICROCOMPUTER in addition to the above described procedures. Be sure to exchange the
MICROCOMPUTER after surely confirming that the trouble is not caused by poor soldering but the MICROCOMPUTER itself.
ELETRICAL MAIN PARTS LIST
REF. NO.
PART NO.
KANRI
NO.
DESCRIPTION
REF. NO.
IC
8A-NH8-610-010
87-A21-018-040
87-A21-396-010
87-A21-417-010
87-A20-783-040
C-IC,LC866560W
C-IC,M65849BFP631D
IC,STK490-040
IC,STK490-310
C-IC,BA7762AFS
87-A21-577-040
87-A20-561-040
87-A21-629-010
87-070-289-040
87-A21-452-040
C-IC,M61506FP
C-IC,M65847AFP
IC,SPS-442-1-N
IC,BU2092F
C-IC,BD3876KS2
87-A21-560-010
87-070-127-110
87-020-454-010
IC,LA1844L-A
IC,LC72131 D
IC,DN6851
TRANSISTOR
87-026-245-080
87-026-609-080
87-A30-198-080
87-026-610-080
87-A30-076-080
TR,DTC114ES
TR,KTA1266GR
TR,KTC3199GR
TR,KTC3198GR
C-TR,2SC3052F
87-A30-075-080
87-A30-318-080
89-213-702-010
87-A30-087-080
87-A30-107-070
C-TR,2SA1235F
TR,CSA952K
TR,2SB1370 (1.8W)
C-FET,2SK2158
C-TR,CMBT5401
87-A30-073-080
87-A30-074-080
87-A30-269-040
87-A30-106-070
87-A30-105-080
C-TR,RT1N 141C
C-TR,RT1P 141C
C-FET,2SJ461-T1
C-TR,CMBT5551
C-TR,RT1P 441C
87-A30-086-040
87-A30-329-080
89-327-143-080
87-A30-072-080
87-A30-234-080
C-TR,CSD1306E
TR,CD1585BC
TR,2SC2714 (0.1W)
C-TR,RT1P 144C
TR,CSC4115BC
89-503-602-080
87-026-463-080
C-FET,2SK360E
TR,2SA933SRS
DIODE
87-A40-548-090
87-017-654-060
87-A40-547-090
87-020-465-080
87-A40-553-080
DIODE,D3SBA20
DIODE,GBU6J
DIODE,D5SBA20
DIODE,1SS133
DIODE,1N4003 LES
87-A40-764-080
87-A40-313-080
87-A40-270-080
87-A40-269-080
87-A40-768-080
ZENER,UZ10BSC
C-DIODE,MC 2840
C-DIODE,MC2838
C-DIODE,MC2836
ZENER,UZ16BSA
87-A40-752-080
87-A40-802-080
87-A40-745-080
87-A40-747-080
87-017-149-080
ZENER,UZ6.2BSC
ZENER,UZ5.1BSC
ZENER,UZ4.7BSA
ZENER,UZ5.1BSB
ZENER,HZS6A2L
87-A40-776-080
ZENER,UZ27BSD
MAIN C.B
C3
C4
C21
C22
C25
87-012-368-080
87-012-368-080
87-016-658-000
87-016-658-000
87-010-406-080
C-CAP,S 0.1-50 F
C-CAP,S 0.1-50 F
CAP,E 4700-35 M SMG
CAP,E 4700-35 M SMG
CAP, ELECT 22-50
C26
C27
C28
87-010-406-080
87-010-406-080
87-010-406-080
CAP, ELECT 22-50

CAP, ELECT 22-50
CAP, ELECT 22-50
PART NO.
C31
C32
C34
C35
C36
KANRI
NO.
87-010-263-080
87-010-197-080
87-010-260-080
87-010-406-080
87-010-381-080
DESCRIPTION
CAP,
CAP,
CAP,
CAP,
CAP,
ELECT 100-10V
CHIP 0.01 DM
ELECT 47-25V
ELECT 22-50V
ELECT 330-16V
C38
C39
C40
C60
C80
87-010-409-080
87-010-409-080
87-010-197-080
87-010-403-080
87-010-401-080
CAP,
CAP,
CAP,
CAP,
CAP,
ELECT 220-50 M
ELECT 220-50 M
CHIP 0.01-25
ELECT 3.3-50V
ELECT 1-50V
C81
C82
C104
C105
C111
87-010-383-080
87-010-260-080
87-010-196-080
87-010-196-080
87-010-545-080
CAP,
CAP,
CHIP
CHIP
CAP,
ELECT 33-25 M
ELECT 47-25V
CAPACITOR,0.1-25
CAPACITOR,0.1-25
ELECT 0.22-50V
C112
C113
C114
C115
C116
87-010-545-080
87-010-545-080
87-010-545-080
87-010-546-080
87-010-546-080
CAP,
CAP,
CAP,
CAP,
CAP,
ELECT
ELECT
ELECT
ELECT
ELECT
C121
C122
C163
C171
C172
87-010-546-080
87-010-546-080
87-010-196-080
87-012-368-080
87-012-368-080
CAP, ELECT 0.33-50V

CAP, ELECT 0.33-50V
CHIP CAPACITOR,0.1-25
C-CAP,S 0.1-50 F
C-CAP,S 0.1-50 F
C173
C174
C301
C302
C303
87-012-368-080
87-012-368-080
87-010-318-080
87-010-318-080
87-012-157-080
C-CAP,S
C-CAP,S
C-CAP,S
C-CAP,S
C-CAP,S
C304
C305
C306
C307
C309
87-012-157-080
87-012-157-080
87-012-157-080
87-010-196-080
87-010-196-080
C-CAP,S 330P-50 CH
C-CAP,S 330P-50 CH
C-CAP,S 330P-50 CH
C310
C311
C312
C313
C314
87-010-196-080
87-010-198-080
87-010-198-080
87-010-178-080
87-010-178-080
CAP, CHIP 0.022-25
CAP, CHIP 0.022-25
CAP,CHIP S 1000P-50 K B
C315
C316
C321
C322
C324
87-010-178-080
87-010-178-080
87-012-142-080
87-012-142-080
87-010-260-080
CAP, S 0.33-16
CAP, S 0.33-16
CAP, ELECT 47-25V
C325
C327
C328
C332
C335
87-010-370-080
87-010-404-080
87-010-404-080
87-010-196-080
87-010-401-080
CAP,E 330-6.3 SME

CAP, ELECT 4.7-50V
CAP, ELECT 4.7-50V
CAP, ELECT 1-50V
C336
C337
C339
C340
C351
87-010-401-080
87-010-196-080
87-010-196-080
87-010-196-080
87-012-140-080
CAP, ELECT 1-50V

CAP 470P-50
C352
C354
C355
C356
C357
87-012-140-080
87-010-175-080
87-010-178-080
87-010-260-080
87-010-197-080
CAP 470P-50
CAP 560P-50
CHIP CAP 1000P-50
CAP, ELECT 47-25V
CAP, CHIP 0.01-25 K B
C358
C359
C360
C370
C373
87-010-183-080
87-010-183-080
87-010-183-080
87-010-196-080
87-016-083-080
C-CAP,S 2700P-50 B
C-CAP,S 2700P-50 B
C-CAP,S 2700P-50 B
C-CAP,S 0.15-16 RK
C374
C378
C379
C380
C386
87-016-083-080
87-010-196-080
87-010-382-080
87-010-382-080
87-010-196-080
C-CAP,S 0.15-16 RK
CAP, ELECT 22-25V
CAP, ELECT 22-25V
0.22-50V
0.22-50V
0.22-50V
0.33-50V
0.33-50V
0.1-50 F
0.1-50 F
47P-50 CH
47P-50 CH
330P-50 CH
REF. NO.
PART NO.
C388
C391
C392
C393
C394
KANRI
NO.
87-012-156-080
87-010-319-080
87-010-319-080
87-010-319-080
87-010-319-080
DESCRIPTION
C-CAP,S
C-CAP,S
C-CAP,S
C-CAP,S
C-CAP,S
220P-50 CH
56P-50 CH
56P-50 CH
56P-50 CH
56P-50 CH
C501
C502
C503
C504
C505
87-010-263-080
87-010-196-080
87-012-393-080
87-012-393-080
87-012-393-080
C506
C507
C508
C509
C510
REF. NO.
C785
C786
C788
C789
C790
KANRI
NO.
87-010-197-080
87-010-197-080
87-010-149-080
87-A10-592-080
87-A10-592-080

C-CAP,S 5P-50 CH
C-CAP,S 0.015-50 J B
C-CAP,S 0.015-50 J B
CAP,E 100-10 M 11L SME

C-CAP,S 0.1-25 Z F C2012
C-CAP,S 0.22-16 K W5R CM/CB
C791
C792
C793
C795
C796
87-010-196-080
87-010-197-080
87-010-404-080
87-010-197-080
87-010-197-080
CHIP
CAP,
CAP,
CAP,
CAP,
87-010-184-080
87-010-177-080
87-016-081-080
87-016-081-080
87-010-184-080
C-CAP,S
C-CAP,S
C-CAP,S
C-CAP,S
C-CAP,S
C797
C798
C799
C800
C801
87-010-405-080
87-010-197-080
87-010-407-080
87-010-194-080
87-010-403-080
CAP, ELECT 10-50V

CAP, CHIP 0.01 DM
CAP, ELECT 33-50V
C-CAP,S 0.047-25 Z F
CAP, ELECT 3.3-50V
C511
C512
C513
C514
C529
87-010-177-080
87-012-393-080
87-010-544-080
87-010-374-080
87-010-197-080
C-CAP,S 820P-50 J SL C2012

CAP,E 0.1-50 M 11L SME
C803
C804
C806
C807
C808
87-010-198-080
87-010-263-080
87-010-401-040
87-010-400-080
87-010-401-080
CAP, CHIP 0.022

CAP, ELECT 100-10V
CAP,E 1-50 SME
CAP, ELECT 0.47-50V
CAP, ELECT 1-50V
C531
C532
C533
C534
C535
87-010-405-080
87-010-196-080
87-010-196-080
87-012-156-080
87-010-178-080

C-CAP,S 0.1-25 Z F C2012
C-CAP,S 0.1-25 Z F C2012
C-CAP,S 220P-50 J CH GRM
C-CAP,S 1000P-50 K B C2012
C809
C810
C811
C812
C814
87-010-401-080
87-010-196-080
87-010-403-080
87-010-403-080
87-010-197-080
CAP,
CHIP
CAP,
CAP,
CAP,
C536
C538
C541
C609
C610
87-010-196-080
87-010-318-080
87-010-178-080
87-010-181-080
87-010-181-080
C-CAP,S 1000P-50 K B C2012
CAP,CHIP S 1800P
CAP,CHIP S 1800P
C815
C816
C821
C823
C824
87-010-400-080
87-010-400-080
87-010-405-080
87-010-177-080
87-010-404-080
CAP, ELECT 0.47-50V

CAP, ELECT 0.47-50V
CAP, ELECT 10-50V
C-CAP,S 820P-50 SL
CAP, ELECT 4.7-50V
C611
C612
C613
C614
C616
87-010-598-080
87-016-369-080
87-010-197-080
87-016-081-080
87-010-184-080
CHIP-CAP,S 0.068-16 K R
C-CAP,S 0.033-25 B K
CAP, CHIP 0.01 DM
C-CAP,S 0.1-16 K R
CHIP CAPACITOR 3300P(K)
C825
C842
C843
C844
C845
87-010-596-080
87-010-197-080
87-010-197-080
87-010-197-080
87-010-197-080
CAP,
CAP,
CAP,
CAP,
CAP,
S 0.047-16
CHIP 0.01-25
CHIP 0.01-25
CHIP 0.01-25
CHIP 0.01-25
C617
C618
C619
C620
C621
87-012-194-080
87-010-401-080
87-010-263-080
87-016-081-080
87-010-197-080
C-CAP,S 0.047-25 Z F
CAP, ELECT 1-50V
CAP, ELECT 100-10V
C-CAP,S 0.1-16 K R
CAP, CHIP 0.01 DM
C846
C847
C848
C849
C850
87-010-197-080
87-010-197-080
87-010-197-080
87-010-197-080
87-010-260-080
CAP,
CAP,
CAP,
CAP,
CAP,
CHIP 0.01-25
CHIP 0.01-25
CHIP 0.01-25
CHIP 0.01-25
ELECT 47-25V
C623
C624
C626
C627
C628
87-010-401-080
87-010-401-080
87-A10-596-080
87-010-400-080
87-010-400-080
CAP, ELECT 1-50V

CAP, ELECT 1-50V
C-CAP,S 0.047-16 K R
CAP, ELECT 0.47-50V
CAP, ELECT 0.47-50V
C851
C852
C853
C858
C859
87-010-197-080
87-010-197-080
87-010-197-080
87-010-196-080
87-010-196-080
CAP,
CAP,
CAP,
CHIP
CHIP
CHIP 0.01-25 K B
CHIP 0.01-25 K B
CHIP 0.01-25 K B
CAPACITOR,0.1-25
CAPACITOR,0.1-25
C629
C630
C631
C632
C634
87-A10-596-080
87-010-263-080
87-010-185-080
87-010-185-080
87-010-196-080
C-CAP,S 0.047-16 K R
C-CAP,S 3900P-50 B
C-CAP,S 3900P-50 B
C860
C940
C941
C943
C945
87-010-197-080
87-010-197-080
87-010-314-080
87-010-197-080
87-010-197-080
CAP, CHIP 0.01 DM

CAP, CHIP 0.01 DM
C-CAP,S 0.01-25 K B C2012
C-CAP,S 0.01-25 K B C2012
C635
C636
C637
C638
C639
87-A10-307-080
87-A10-307-080
87-A10-307-080
87-A10-307-080
87-010-405-080
CAP,M 0.1-50 J
CAP,M 0.1-50 J
CAP,M 0.1-50 J
CAP,M 0.1-50 J
CAP, ELECT 10-50V
C946
C947
C948
C952
C953
87-010-971-080
87-010-197-080
87-010-148-080
87-010-197-080
87-010-197-080
C-CAP,S
C-CAP,S
C-CAP,S
C-CAP,S
C-CAP,S
C643
C644
C671
C672
C673
87-010-196-080
87-010-401-080
87-010-322-080
87-010-322-080
87-010-197-080
CAP, ELECT 1-50V
C-CAP,S 100P-50 CH
C-CAP,S 100P-50 CH
CAP, CHIP 0.01 DM
C954
C956
C959
C962
C963
87-010-400-080
87-010-263-080
87-010-196-080
87-010-401-080
87-015-785-080
CAP,E 0.47-50 M 11L SME

CHIP CAPACITOR, 0.1FZ-25Z
C679
C680
C771
C772
C685
87-010-196-080
87-010-197-080
87-010-263-080
87-010-197-080
87-010-190-080
CAP, CHIP 0.01 DM
CAP, ELECT 100-10V
CAP, CHIP 0.01 DM
C-CAP,S 0.01-50 Z F
C964
C971
C972
C973
C974
87-010-854-080
87-010-381-080
87-010-404-080
87-010-197-080
87-010-197-080
C-CAP,S 560P-50 J CH
CAP, ELECT 330-16V
CAP, ELECT 4.7-50V
CAP, CHIP 0.01 DM
CAP, CHIP 0.01 DM
C779
C780
C782
C783
C784
87-010-182-080
87-010-182-080
87-010-197-080
87-010-197-080
87-010-197-080
C-CAP,S 2200P-50 K B C2012

C-CAP,S 2200P-50 K B C2012
C979
C981
C982
C983
C984
87-010-322-080
87-010-260-080
87-010-196-080
87-010-197-080
87-010-197-080
C-CAP,S 100P-50 CH
CAP, ELECT 47-25V
CAP, CHIP 0.01 DM
CAP, CHIP 0.01 DM
3300P-50 K B C2012
820P-50 J SL C2012
0.1-16 K R GRM
0.1-16 K R GRM
3300P-50 K B C2012
PART NO.
DESCRIPTION
CAPACITOR,0.1-25
CHIP 0.01 DM
ELECT 4.7-50V
CHIP 0.01 DM
CHIP 0.01 DM
ELECT 1-50V
CAPACITOR,0.1-25
ELECT 3.3-50V
ELECT 3.3-50V
CHIP 0.01 DM
K
K
K
K
B
B
B
B
K
K
K
K
B
B
B
B
4700P-50 J B
0.01-25 K B C2012
4P-50 J CH GRM
0.01-25 K B C2012
0.01-25 K B C2012
REF. NO.
PART NO.
C987
C989
C991
C992
C993
KANRI
NO.
87-010-197-080
87-010-197-080
87-010-312-080
87-010-312-080
87-010-178-080
DESCRIPTION
CAP, CHIP 0.01
CAP, CHIP 0.01
C-CAP,S 15P-50
C-CAP,S 15P-50
CHIP CAP 1000P
C995
C997
C998
C999
CF831
87-010-178-080
87-010-196-080
87-010-260-080
87-A11-155-080
87-008-261-010
CF832
CN1
CN91
CN101
CN301
REF. NO.
C209
C210
C211
C251
C253
KANRI
NO.
87-010-322-080
87-010-322-080
87-010-322-080
87-010-405-040
87-010-196-080
C-CAP,S 100P-50 CH
C-CAP,S 100P-50 CH
C-CAP,S 100P-50 CH
CAP,E 10-50
CHIP CAP 1000P

CAP, ELECT 47-25V
CAP,TC U 0.01-16 Z F
FILTER, SFE10.7MA5-A
C254
C255
C256
C259
C264
87-012-369-080
87-010-560-040
87-010-405-040
87-010-405-040
87-018-209-080
C-CAP,S 0.047-50F
CAP,E 10-50 GAS
CAP,E 10-50
CAP,E 10-50
CAP, CER 0.1-50V
87-008-261-010
87-A60-996-010
87-A60-109-010
87-A60-996-010
87-099-827-010
FILTER, SFE10.7MA5-A
CONN,13P V BLK TAC-L13X-A3
CONN,2P V S2M-2W
CONN,13P V BLK TAC-L13X-A3
CONN,3P V S 2M-3W
C273
C274
C301
C302
C303
87-010-178-080
87-010-178-080
87-010-182-080
87-010-196-080
87-010-196-080
CHIP CAP 1000P

CHIP CAP 1000P
C-CAP,S 2200P-50 B
CN351
CN601
CN606
CN602
CNA1
87-099-832-010
87-099-719-010
87-099-566-010
87-099-194-010
8A-NF8-653-010
CONN,8P V S 2M-8W
CONN,30P TYK-B(X)
CONN,7P TUC-P7P-B1
CONN,6P 6216V
CONN ASSY,9P TID-A(480)
C312
C314
C315
C316
C321
87-010-498-040
87-010-196-080
87-010-196-080
87-010-196-080
87-012-393-080
CAP,E 10-16 GAS

C-CAP,S 0.22-16 R K
CNA2
D951
FB501
FC602
FFE831
8A-NF6-630-110
87-A40-618-080
87-008-372-080
85-NF5-617-010
A8-8ZA-190-030
CONN ASSY,3P (VM) ANF-6

VARI-CAP,SVC348(S/T)
FLTR,EMI BL01 RN1
CABLE,FFC 6P-1.25
8ZA-1 FEUNM
C322
C325
C326
C332
C334
87-010-400-040
87-A10-189-040
87-A10-189-040
87-010-178-080
87-010-312-080
CAP,E 0.47-50
CAP,E 220-10
CAP,E 220-10
CHIP CAP 1000P
C-CAP,S 15P-50 CH
J101
J102
J604
J831
J940
87-A60-483-010
87-A60-238-010
87-A60-881-010
87-A60-202-010
81-754-629-010
JACK,DIA6.3 BLK ST W/S KM

TERMINAL,SP 4P (MSC)
JACK,PIN 2P MSP 242VO5
TERMINAL,ANT 4P MSP-154V-02
CONNECTOR X11 2P (UL)
C335
C336
C339
C340
C341
87-012-140-080
87-012-155-080
87-012-156-080
87-010-197-080
87-010-194-080
CAP 470P
C-CAP 180P-50CH
C-CAP,S 220P-50 CH
CAP, CHIP 0.01 DM
CAP, CHIP 0.047
L101
L102
L301
L302
L351
87-003-383-010
87-003-383-010
87-A50-049-010
87-A50-049-010
87-007-342-010
COIL,1UH K
COIL,1UH K
COIL,TRAP 85K(COI)
COIL,TRAP 85K(COI)
COIL,OSC 85K BIAS
C351
C401
C451
C452
C453
87-010-981-040
87-010-197-080
87-010-196-080
87-010-196-080
87-010-196-080
CAP,E 22-25 M SRE

CAP, CHIP 0.01 DM
L801
L802
L811
L832
L941
87-A50-608-010
87-A91-552-010
87-005-847-080
87-005-847-080
87-A50-022-010
COIL,FM DET-N(TOK)
FLTR,CFMT-450AL (AOK)
COIL,2.2UH(CECS)
COIL,2.2UH K CECS
COIL,ANT SW (COI) 7.96MHZ
C454
C455
C458
C459
C502
87-010-198-080
87-010-198-080
87-010-320-080
87-010-320-080
87-010-186-080
CAP, CHIP 0.022

CAP, CHIP 0.022
CHIP CAP 68P
CHIP CAP 68P
CAP,CHIP 4700P
L942
L943
L944
L952
L953
87-A50-550-010
87-A50-522-080
87-A50-159-010
87-A50-430-010
87-A50-431-010
COIL,OSC SW-2N (COI)

COIL,1MH K CEC
COIL,10MH K C2B
COIL,ANT MW(3BSW)
COIL,OSC MW(3BSW)
C503
C504
C505
C506
C513
87-010-112-040
87-010-405-040
87-010-545-040
87-010-320-080
87-010-196-080
CAP,E 100-16
CAP,E 10-50
CAP,E 0.22-50 SME
CHIP CAP 68P
R161
R162
R163
R164
R790
87-A00-440-050
87-A00-440-050
87-A00-440-050
87-A00-440-050
87-010-197-080
RES,220-1/2W J RP
RES,220-1/2W J RP
RES,220-1/2W J RP
RES,220-1/2W J RP
C514
C515
C602
C603
C604
87-010-196-080
87-010-178-080
87-010-322-080
87-010-322-080
87-010-322-080
CHIP CAP 1000P
C-CAP,S 100P-50 CH
C-CAP,S 100P-50 CH
C-CAP,S 100P-50 CH
R991
R993
R995
SFR351
SFR352
87-010-322-080
87-010-322-080
87-010-322-080
87-A90-433-080
87-A90-433-080
C-CAP,S
C-CAP,S
C-CAP,S
SFR,50K
SFR,50K
100P-50 CH
100P-50 CH
100P-50 CH
H NVZ6TLTA
H NVZ6TLTA
C650
C699
CN101
CN102
CN301
87-010-196-080
87-010-196-080
87-099-720-010
87-099-015-010
87-A60-140-010
CONN,30P TYK-B(P)
CONN,13P 6216V
CONN,15P V FE
TC941
TC943
WH1
X991
87-011-254-080
87-011-253-080
87-A90-510-010
87-A70-061-010
TRIMMER,CER 20P 4.0X4.5 ECR

TRIMMER,CER 30P 4.0X4.5 ECR
HLDR,WIRE 2.5-9P
VIB,XTAL 4.500MHZ CSA-309
FB301
FB501
FL401
J501
L331
87-008-372-080
87-008-372-080
8A-NF8-602-010
87-A61-242-010
87-A50-408-010
FILTER, EMI BL OIRNI

FILTER, EMI BL OIRNI
FL,HNA-11MM31(ANF-8VCD)
JACK,6.3 BLK MONO W/SW V KM
COIL,OSC 5.76MHZ
LED311
LED601
LED602
LED603
LED604
87-A40-589-040
87-A40-803-010
87-A40-619-080
87-A40-619-080
87-A40-619-080
LED,SLR-56VCT31 RED
LED,SELU1E10CXM-S LF38 BLUE
LED,SLR-56PT-TE7-W GRN
LED606
LED607
LED608
S401
S402
87-A40-619-080
87-A40-619-080
87-A40-619-080
87-A91-024-180
87-A91-024-180
SW,TACT KSHG611BT
SW,TACT KSHG611BT
DM
DM
CH
CH
FRONT C.B
C201
C202
C203
C204
C205
87-010-322-080
87-010-322-080
87-010-322-080
87-010-322-080
87-010-322-080
C-CAP,S
C-CAP,S
C-CAP,S
C-CAP,S
C-CAP,S
100P-50
100P-50
100P-50
100P-50
100P-50
CH
CH
CH
CH
CH
C206
C207
C208
87-010-322-080
87-010-322-080
87-010-322-080
C-CAP,S 100P-50 CH
C-CAP,S 100P-50 CH
C-CAP,S 100P-50 CH
PART NO.
DESCRIPTION
REF. NO.
PART NO.
S403
S404
S405
S406
S407
KANRI
NO.
87-A91-024-180
87-A91-024-180
87-A91-024-180
87-A91-024-180
87-A91-024-180
DESCRIPTION
SW,TACT
SW,TACT
SW,TACT
SW,TACT
SW,TACT
KSHG611BT
KSHG611BT
KSHG611BT
KSHG611BT
KSHG611BT
S408
S409
S410
S411
S412
87-A91-024-180
87-A91-024-180
87-A91-024-180
87-A91-024-180
87-A91-024-180
SW,TACT
SW,TACT
SW,TACT
SW,TACT
SW,TACT
S413
S414
S415
S416
S417
87-A91-024-180
87-A91-024-180
87-A91-024-180
87-A91-024-180
87-A91-024-180
S418
S419
S420
S421
S422
REF. NO.
C223
C224
C251
C252
C253
KANRI
NO.
87-010-197-080
87-010-197-080
87-010-196-080
87-010-196-080
87-010-196-080
CAP,
CAP,
CHIP
CHIP
CHIP
KSHG611BT
KSHG611BT
KSHG611BT
KSHG611BT
KSHG611BT
C254
C259
C260
C401
CN101
87-010-196-080
87-010-197-080
87-010-197-080
87-010-260-080
87-A61-011-010
CAP, CHIP 0.01 DM
CAP, CHIP 0.01 DM
CAP, ELECT 47-25
CONN,13P H BLK TAC-L13P-A3
SW,TACT
SW,TACT
SW,TACT
SW,TACT
SW,TACT
KSHG611BT
KSHG611BT
KSHG611BT
KSHG611BT
KSHG611BT
CN102
CNA101
J201
L251
L252
87-A61-011-010
8A-NF8-656-010
87-A61-148-010
87-003-383-010
87-003-383-010
CONN,13P H BLK TAC-L13P-A3

CONN ASSY,5P TID-A 400
JACK,PIN 4P R/W BLUE
COIL,1UH K
COIL,1UH K
87-A91-024-180
87-A91-024-180
87-A91-024-180
87-A91-024-180
87-A91-024-180
SW,TACT
SW,TACT
SW,TACT
SW,TACT
SW,TACT
KSHG611BT
KSHG611BT
KSHG611BT
KSHG611BT
KSHG611BT
R129
R130
R231
R232
WH101
87-A00-257-080
87-A00-257-080
87-A00-258-080
87-A00-258-080
87-A90-459-010
RES,M/F 0.15-1W J
RES,M/F 0.15-1W J
RES,M/F 0.22-1W J
RES,M/F 0.22-1W J
HLDR,WIRE 2.5-5P
S423
S425
S426
S428
S429
87-A91-024-180
87-A91-024-180
87-A91-024-180
87-A91-024-180
87-A91-024-180
SW,TACT
SW,TACT
SW,TACT
SW,TACT
SW,TACT
KSHG611BT
KSHG611BT
KSHG611BT
KSHG611BT
KSHG611BT
S432
S433
S434
S435
S436
87-A91-024-180
87-A91-024-180
87-A91-024-180
87-A91-024-180
87-A91-024-180
SW,TACT
SW,TACT
SW,TACT
SW,TACT
SW,TACT
KSHG611BT
KSHG611BT
KSHG611BT
KSHG611BT
KSHG611BT
S437
SW252
SW253
87-A91-024-180
87-A91-555-010
87-A91-542-010
SW,TACT KSHG611BT
SW,RTRY EC12E24504
SW,RTRY EC12E12504
C101
C102
C103
C104
C107
87-010-181-080
87-010-181-080
87-010-545-080
87-010-545-080
87-010-405-080
C-CAP,S 1800P-50 B
C-CAP,S 1800P-50 B
CAP, ELECT 0.22-50V
CAP, ELECT 0.22-50V
CAP, ELECT 10-50V
C108
C111
C112
C113
C114
87-010-405-080
87-010-179-080
87-010-179-080
87-010-405-080
87-010-405-080
CAP, ELECT 10-50V

C-CAP,S 1200P-50 K B GRM
CAP, ELECT 10-50V
CAP, ELECT 10-50V
C115
C116
C119
C120
C133
87-010-866-080
87-010-866-080
87-010-197-080
87-010-197-080
87-010-197-080
CAP,
CAP,
CAP,
CAP,
CAP,
CHIP 0.01 DM
CHIP 0.01 DM
CAPACITOR,0.1-25
CAPACITOR,0.1-25
CAPACITOR,0.1-25
C153
C201
C202
C203
C204
87-010-188-080
87-A10-300-080
87-A10-300-080
87-A10-300-080
87-A10-300-080
C-CAP,S 6800P-50 K B C2012

CAP,M 0.027-50 J
CAP,M 0.027-50 J
CAP,M 0.027-50 J
CAP,M 0.027-50 J
C205
C206
C207
C208
C209
87-010-180-080
87-010-180-080
87-010-401-080
87-010-401-080
87-010-187-080
C-CER 1500P
C-CER 1500P
CAP, ELECT 1-50V
CAP, ELECT 1-50V
CAP CHIP S5600P
C210
C211
C212
C215
C216
87-010-187-080
87-010-403-080
87-010-403-080
87-010-179-080
87-010-179-080
CAP CHIP S5600P

CAP, ELECT 3.3-50V
CAP, ELECT 3.3-50V
C217
C218
C221
C222
87-010-405-080
87-010-405-080
87-010-405-080
87-010-405-080
CAP,
CAP,
CAP,
CAP,
!
!
C551
C552
C553
C554
C555
87-A10-060-080
87-A10-060-080
87-012-154-080
87-012-154-080
87-012-145-080
C-CAP,S
C-CAP,S
C-CAP,S
C-CAP,S
C-CAP,S
0.18-16 KB
0.18-16 KB
150P-50
150P-50
270P-50
C556
C557
C559
C560
C561
87-012-145-080
87-010-183-080
87-010-196-080
87-010-177-080
87-010-177-080
C-CAP,S 270P-50
C-CAP,S 2700P-50 B
C-CAP,S 820P-50 SL
C-CAP,S 820P-50 SL
C562
C563
C564
C565
C567
87-010-196-080
87-010-374-080
87-010-196-080
87-010-263-080
87-010-183-080
CAP, ELECT 47-10V
CAP, ELECT 100-10V
C-CAP,S 2700P-50 B
C571
C572
C573
C577
CN551
87-016-460-080
87-016-460-080
87-016-460-080
87-010-196-080
87-A60-689-010
C-CAP,S 0.22-16 K B
C-CAP,S 0.22-16 K B
C-CAP,S 0.22-16 K B
CONN,7P H GRY TUC-P07X-C1
87-049-919-010
CONN,3P V WHT EH
C1
C4
C5
C6
C7
87-010-387-080
87-A11-148-080
87-A11-148-080
87-016-051-000
87-016-051-000
CAP,E 470-25 SME

CAP,TC U 0.1-50 Z F
CAP,TC U 0.1-50 Z F
CAP,E 2200-35 M SMG
CAP,E 2200-35 M SMG
C8
C9
C10
C11
C12
87-A11-148-080
87-A11-148-080
87-A11-148-080
87-A11-148-080
87-016-520-000
CAP,TC U 0.1-50
CAP,TC U 0.1-50
CAP,TC U 0.1-50
CAP,TC U 0.1-50
CAP,E 3300-65 M
C13
C14
C15
C16
C91
87-016-520-000
87-A11-148-080
87-A11-148-080
87-010-403-080
87-A10-479-080
CAP,E 3300-65 M SMG

CAP,TC U 0.1-50 Z F
CAP,TC U 0.1-50 Z F
CAP, ELECT 3.3-50V
CAP, CER 2200P-250 M E KH
C92
CN1
CN2
PT1
PT2
87-A10-479-080
87-A61-110-010
87-A61-108-010
8A-NH8-606-010
8A-NF8-673-010
CAP, CER 2200P-250 M E KH

CONN,9P V TID-A
CONN,5P V TID-A
PT,ANF-8 HR
PT,SUB ANF-8 (H) KAMI
VM C.B
CNA3
ELECT 10-63
ELECT 10-63
CHIP 0.01 DM
CHIP 0.01 DM
CHIP 0.01 DM
10-50V
10-50V
10-50V
10-50V
DESCRIPTION
KEY CON C.B
AMP 1F C.B
ELECT
ELECT
ELECT
ELECT
PART NO.
PT C.B
Z F
Z F
Z F
Z F
SMG
REF. NO.
!
!
!
!
RY1
S1
T1
T2
PART NO.
KANRI
NO.
87-A91-339-010
87-A90-165-010
87-A60-317-010
87-A60-317-010
DESCRIPTION
REF. NO.
RELAY,AC DC12V G5PA-2

SW,SL 1-2-3 SWS2301
TERMINAL, 1P MSC
TERMINAL, 1P MSC
PART NO.
KANRI
DESCRIPTION
NO.
87-A90-248-010
SW,MICRO ESE11SH2CXQ
87-A90-248-010
82-ZM3-601-010
RBN,CORD,4P-75
SW8
SW9
W1
HEAD-1 C.B
DECK C.B
CON105
SFR1
SOL1
SOL2
SW1
87-099-756-010
87-024-581-010
82-ZM1-618-410
82-ZM1-618-410
87-A90-248-010
CONN,15P 9604 S F
SFR,3.3K DIA 6H
SOL ASSY,27
SOL ASSY,27
87-A90-248-010
87-A90-248-010
87-036-110-010
87-036-110-010
87-036-110-010
SW,MICRO
SW,MICRO
SW,MICRO
SW,MICRO
SW,MICRO
PWB,FLEX A
85-ZM3-602-010
87-NF6-616-010
PWB,FLEX A
CONN ASSY,8P-RPB
HEAD-2 C.B
CON351
SW2
SW3
SW4
SW5
SW6
85-ZM3-602-010
ESE11SH2CXQ
ESE11SH2CXQ
SPPB62
SPPB62
SPPB62
CHIP RESISTOR PART CODE
Chip Resistor Part Coding
8 8
A
Figure
Resistor Code
Value of resistor
Chip resistor
L
:A
Resistor Code : A
1.0
0.5
0.35
104
1.6
0.8
0.45
108
1.25
0.45
118
3.2
1.6
0.55
128
Dimensions (mm)
Wattage
1/16W
Type
1005
Tolerance
5%
Symbol
CJ
1/16W
1/10W
1608
2125
5%
5%
CJ
CJ
1/8W
3216
5%
CJ
Form
L
t
W
10
TRANSISTOR ILLUSTRATION
B
E
E C B
CD1585BC
CSA952K
CSC4115BC
KTA1266GR
KTC3198GR
E C B
B C E
DTC114ES
KTC3199GR
2SB1370
G
S
2SK2158
2SJ461-T1
2SK360E
11
2SA1235F
2SA933SRS
2SC2714
2SC3052F
CMBT5401
CMBT5551
CSD1306E
RT1N141C
RT1P141C
RT1P144C
RT1P441C
WIRING 1 (MAIN / VM)

32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
1
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
12
SCHEMATIC DIAGRAM 1 (MAIN 1 / 3 : AMP / VM)
13
SCHEMATIC DIAGRAM 2 (MAIN 2 / 3 : DECK / HEAD-1 / HEAD-2)
14
SCHEMATIC DIAGRAM 3 (MAIN 3 / 3 : TUNER)
15
WIRING 2 (FRONT)
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
1
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
16
SCHEMATIC DIAGRAM 4 (FRONT)
17
WIRING 3 (AMP 1F)<HR>

32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
1
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
18
WIRING 4 (AMP 1F)<HT>

32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
1
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
19
SCHEMATIC DIAGRAM 5 (AMP 1F)
20
WIRING 5 (KEY CON)

15
14
13
12
11
10
1
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
21
SCHEMATIC DIAGRAM 6 (KEY CON)
22
WIRING 6 (PT)
15
14
13
12
11
10
1
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
16
SCHEMATIC DIAGRAM 7 (PT)
24
WIRING 7 (DECK)
15
14
13
12
11
10
1
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
25
FL (HNA-11MM31) GRID ASSIGNMENT AND ANODE CONNECTION

GRID ASSIGNMENT
26
ANODE CONNECTION
27
IC BLOCK DIAGRAM
28
29
IC DESCRIPTION
IC, LC866560W
Pin No.
Pin Name
Description
I/O
I-STEREO/I-DRF
Stereo detect input / CD DRF input.
I-IFC/I-SUBQ
Tuner IFC input / CD SUBQ detect input.
NC
Not connected.
O-POWER
System power ON/OFF output.
O-CD_ON/I-HP MUTE
O/I
O-DSC_CE/PLL_DATA
LED driver, Tuner IC, Function IC, Data output.
O-RMT
REC mute output.
NC
Not connected.
O-MUTE
System mute ON/OFF output.
10
O-STB
Strobe output for MAIN C.B.
11
O-CLK_SFT
Micon clock shift output.
12
RESET
System reset.
13
NC
Not connected.
14
I-DISH
CD turntable photo sensor input.
15
VSS1
Connected to GND.
16
CF1
5.76 MHz oscillator circuit.
17
CF2
18
VDD1
Power supply.
19
I-HOLD
Power supply voltage detect A/D input.
20 ~ 22
I-KEY 1 ~ 3
KEY 1 ~ 3 A/D input.
23
I-TU_SIG
RDS data input (not used).
24
I-CDSW
CD mecha switch input.
25
I-SPEANA
A/D input for spectrum analyser level display.
26
I-RE_VOL
Rotary encoder input (VOL).
27
I-WRQ/I-RDS_CLK
CD WRQ input / RDS clock input (not used).
28
I-TM_BASE
Base input for clock.
29
I-RMC
Remote control signal input. Active: "L".
30 ~ 40
G11 ~ G1
FL grid G11 ~ G1 output.
41
NC
Not connected.
42 ~ 45
P35 ~ P32
FL segment P35 ~ P32 output.
46
VDD3
Power supply.
47, 48
P31, P30
FL segment P31, 30 output.
49
P29/O-SPEANA-C
FL segment P29 output / Spectrum analyzer band select output (C) .
50
P28/O-SPEANA-B
FL segment P28 output / Spectrum analyzer band select output (B).
51
-VFL
Power supply input for FL display.
52
P27/O-SPEANA-A
FL segment P27 output / Spectrum analyzer band select output (A).
53, 54
P26, P25
FL segment P26, P25 output.
55
P24/I-KARAOKE
O/I
56 ~ 59
P23 ~ 20
60
P19/SW
O/I
61 ~ 63
P18 ~ P16
Headphones connect detect input.
FL segment P24 output / KARAOKE input to diode.

FL segment P19 output / SW mode data input.
30
Pin No.
Pin Name
I/O
64
P15/I-CST2
O/I
FL segment P15 output / Deck 2 cassette detect switch input.
65
P14/I-REB
O/I
FL segment P14 output / Deck side B record permission switch input.
66
P13/I-CAM2
O/I
FL segment P13 output / Deck 2 CAM switch input.
67
P12/I-AUTO1
O/I
FL segment P12 output / Deck 1 auto stop input.
68
P11/I-AUTO2
O/I
FL segment P11 output / Deck 2 auto stop input.
69
P10/I-CAM1
O/I
FL segment P10 output / Deck 1 CAM switch input.
70
P9/I-CST1
O/I
FL segment P9 output / Deck 1 cassette detect switch input.
71
P8/I-REA
O/I
FL segment P8 output / Deck side A record permission switch input.
72
VDD4
73
P7/I-REV2
O/I
FL segment P7 output / Deck 2 reverse mode input to diode.
74
P6/I-REV1
O/I
FL segment P6 output / Deck 1 reverse mode input to diode.
75
P5/NO_ECO
O/I
FL segment P5 output / NO ECO mode input to diode.
76 ~ 79
P4 ~ P1
FL segment output (P4 ~ P1).
80
O-CD_CLOSE
CD tray close output.
81
O-CD_OPEN
CD tray open output.
82
NC
Not connected.
83
I-JOG_A
Jog dial rotary encoder input A.
84
I-JOG_B
Jog dial rotary encoder input B.
85
O-DISH_FWD
CD turn table forward revolution output.
86
O-DISH_REV
CD turn table reverse revolution output.
87
O-PLLCE
Chip enable output for tuner PLL.
88
O-KEYSCAN
Key scan timing output.
89
VSS2
Connected to GND.
90
VDD2
Power supply.
91
LED-STBY
STBY LED on output (STBY LED on during O-POWER OFF).
92
O-MOTOR
DECK motor output.
93
O-SOL1
DECK1 plunger ON/OFF output.
94
O-SOL2
DECK2 plunger ON/OFF output.
95
O-CD_DATA
CD data output.
96
O-CDLED
CD flash window LED ON/OFF output.
97
O-CD-CLK
CD CLK output.
98
O-CDCE
CD CD output.
99
I-RDS-DATA
RDS data input. (Not used)
100
O-PLL_CLK
PLL clock enable output.
Description
Power supply.
31
ADJUSTMENT (TUNER / DECK / FRONT)

A MAIN C.B
14
L941
TC943
L802
L801
SFR351
SFR352
IC303
TP3
IC801
CN351
R815
24
TP2
(CLK)
TC941
L942
TP4
L953
L952
4
TP1 FFE831
(VT)
GND
3
TP8 (LCH)
TP9 (RCH)
IC601
8
9
10
11
12
13
14
15
< TUNER SECTION >

1. Clock Frequency Check
Settings : Test point :
TP2 (CLK)
Method : Set to MW 1602kHz and check that the test point is
2052kHz 45Hz.
5. SW Tracking Adjustment
TP8 (Lch), TP9 (Rch)
Ajustment location :
L941............................... 5.73MHz
TC943.............................17.9MHz
Method : Set up TC943 to center before adjustment. Adjust L941
so that level at 5.73MHz becomes maximum. Then
adjust TC943 so that the level at 17.9MHz becomes
maximum.
2. MW VT Adjustment
TP1 (VT)
Adjustment location : L953
Method : Set to MW 1710kHz and adjust L953 so that the test
point becomes 8.0V 0.05V. Then set to MW 530kHz
and check that the test point is more than 0.3V.
3. MW Tracking Adjustment
Adjustment location :
L952............................... 603kHz
TC941............................ 1404kHz
Method : Set up TC941 to center before adjustment. Adjust L952
so that level at 603kHz becomes maximum. Then adjust
TC941 so that the level at 1404kHz becomes maximum.
4. SW VT Adjustment
TP1 (VT)
Method : Set to SW 17.9MHz and adjust L942 so that the
test point becomes 8.0V 0.05V. Then set to SW
5.73MHz and check that the test point is more than 0.3V.
6. FM VT Check
TP1 (VT)
Method : Set to FM 108.0MHz and check that the test point is less
than 8.0V. Then set to FM 87.5MHz and check that the
test point is more than 0.5V.
7. FM Tracking Check
Method : Set to FM 98.0MHz and check that the test point is less
than 9.0dBV.
8. AM IF Adjustment
Adjustment location : L802............450kHz
9. DC Balance / Mono Distortion Adjustment
TP3, TP4 (DC Balance)
Input level :
60dBV
Method : Set to FM 98.0MHz and adjust L801 so that the voltage
between TP3 and TP4 becomes 0V 0.3V.
Next, check that the distortion is minimum.
32
B FRONT C.B
R628
FL401
C326
IC101
TP5
(K-SCAN)
100
TP6
(GND)
L331
16
DECK-1 P,DECK-2 R/P/E HEAD
G DECK C.B
SFR1
10
11
11
< DECK SECTION >

14. REC/PB Frequency Response Adjustment (DECK 2)
Settings : Test tape :
TTA-602
Test point :
Input signal :
8kHz/1kHz (LINE IN)
Adjustment location : SFR351 (Lch), SFR352 (Rch)
Method : Apply a 1kHz signal and REC mode. Then adjust OSC
attenuator so that the output level at the test points
becomes 10mV. Record and play back the 1kHz and
8kHz signals and adjust SFRs so that the output level of
the 8kHz signals becomes 0dB 0.5dB with respect to
that of the 1kHz signal.
10. Tape Speed Adjustment (DECK 2)

TTA-100 (3kHz)
Test point :
Adjustment location : SFR1
Method : Play back the test tape and adjust SFR1 so that the
frequency counter reads 3000Hz 5Hz (FWD) and
FWD SPEED 45Hz (REV).
11. Head Azimuth Adjustment (DECK 1, DECK 2)
TTA-330
Test point :
Adjustment location : Azimuth adjustment screw
Method : Play back (FWD) the 8kHz signal of the test tape and
adjust screw so that the output becomes maximum.
Next, perform on REV PLAY mode.
15. REC/PB Sensitivity Check (DECK 2)

TTA-602
Test point :
Input signal :
1kHz (LINE IN)
Method : Apply a 1kHz signal and REC mode. Then adjust OSC
attenuator so that the output level at the test points
becomes 100mV. Record and play back the 1kHz signal
and check that the output is -2dB 3dB.
12. PB Frequency Response Check (DECK 1, DECK 2)

TTA-330
Test point :
Method : Play back the 315Hz and 8kHz signals of the test tape
and check that the output ratio of the 8kHz signal with
respect to that of the 315Hz signal is within 0 5.0dB.
<FRONT SECTION>
13. PB Sensitivity Check (DECK1, DECK2)

TTA-200
Test point :
Method : Play back the test tape and check that the output level of
the test piont is 230mV 3dB.
16. -CON OSC Adjustment

Settings : Test point : TP5 (K-SCAN) and TP6 (GND)
Method : Insert AC plug with pressing of POWER and TUNER
function key. Adjust L331 so that the frequency across
the test point is 153.85Hz 0.15Hz.
33
CD TEST MODE
1. How to Activate CD Test Mode
Insert the AC plug while pressing the function CD button.
All FL display tubes will light up, and the test mode will be
activated.
2. How to Cancel CD Test Mode

Either one of the following operations will cancel the CD test
mode.
Press the function button.
Press the power switch button.
(except CD function button) Disconnect the AC plug
3. CD Test Mode Functions

When test mode is activated, the following mode functions from No.1 to No.5 can be used by pressing the operation keys.
Mode/No.
Start mode
No.1
Search mode
FL display
All lamps light
Operation
Activation
9 key
No.2
Play mode
No.3
Traverse mode
No.4
Sled mode
1 2 key
key
key
All lamps light
No.5
Operation
Test mode is activated.
CD block power is ON.
Laser diode turns always ON.
Continual focus search
(The pickup lens repeats the fullswing up-down motion.)
Avoid continual searches that last for
more than 10 minutes.
Contents
FL display check (All displays light.)
APC circuit check

Laser current measurement
(Laser current control. Across a
resistor connected between emitter
and GND.)
FOCUS SERVO
Check focus search waveform
Check focus error waveform
(FOK/FZC are not monitored in the
* NOTE 1
search mode)
Normal playback
FOCUS SERVO/TRACKING SERVO
Focus search is continued if TOC
CLV SERVO/SLED SERVO
cannot be read.
* NOTE 1 Check DRF
During normal disc playback
TRACKING SERVO ON/OFF
Press once; tracking servo OFF
Tracking balance (traverse) check
Press twice; tracking servo ON
* NOTE 2
Pickup moves to the outermost track SLED SERVO
Pickup moves to the innermost track Check SLED mechanism operation

* NOTE 3
(During playback, machine operates
normally.)
* NOTE 1: There are cases when the tracking servo cannot be locked owing to the protection circuit being operated when heat builds up
in the driver IC if the focus search is operated continually for more than 10 minutes. In these cases the power supply should be
switched off for 10 minutes until heat has been reduced and then re-started.
* NOTE 2: Do not press the or keys when the machine is in the ; status is active. If they are pressed, playback will not be possible
after the ; status has been canceled. If the or keys are pressed in the ; status, press the 9 key and return to the start mode
(No.1).
* NOTE 3: When pressing the or keys, take care to avoid damage to the gears. Because the sled motor is activated when the or
keys are pressed, even when the pick-up is at the outermost or innermost track.
4. Operation Outline
The operation of each mode is carried out in the direction of the arrows from the start mode as indicated in the following illustration.
No. 2
No. 3
Search mode
Play mode
1 2
9
9
No. 1
1 2
Start mode
(All FLs light up.)
No. 5
Sled mode
No. 4
Traverse mode
If the DISC DIRECT PLAY button is pressed, the machine performs the same operation as the PLAY button is pressed as shown. If
the tray is opened by pressing OPEN/CLOSE button during Play mode or Traverse mode, the machine returns to the Start mode.
34
MECHANICAL EXPLODED VIEW 1 / 1

<HT>
<HR>
AZG-1 VZD3RDM<HR>
AZG-1 VZD3RNDM<HT>
A
F
c
a
F
58
57
F
b
F
b
7
<HR>
13
a
12
15
36
27
2ZM-3MK2 PR4NM
44
11
35
MECHANICAL PARTS LIST 1 / 1
REF. NO. PART NO.
1
2
3
4
5
8A-NFJ-012-010
8A-NFJ-013-010
8A-NFJ-035-010
8A-NFJ-036-010
82-NF5-218-010
KANRI
DESCRIPTION
NO.
WINDOW,CASS 1
WINDOW,CASS 2
BOX,CASS 1H
BOX,CASS 2H
SPR-T,EJECT 1 (SIN)
6
7
8
9
10
82-NF5-219-010
8A-NF7-226-010
8A-NFJ-017-010
8Z-NF6-210-010
8A-NHJ-001-010
12
13
14
15
16
REF. NO. PART NO.
KANRI
DESCRIPTION
NO.
HLDR,LOCK 1
SPR-C,LOCK
PLATE,LOCK
HLDR,LOCK 2
HLDR,PWB M
37
38
39
40
41
87-NF4-216-010
86-NF9-224-010
82-NF5-229-010
87-NF4-217-110
8A-NF8-206-010
SPR-T,EJECT 2 (SIN)
HLDR,IC2-T2
KNOB,RTRY JOG
DMPR,150 N
CABI,FR H
42
43
44
45
46
88-906-251-110
8A-NFJ-046-010
8A-NF7-112-010
8A-NF7-207-010
87-A91-711-010
FF-CABLE,6P 1.25
KEY,ECHO
PANEL,RIGHT V-2<HR>
HLDR,HT L
FAN,3110GL-B4W-B34-H02-400MM
8A-NHJ-003-010
87-A80-092-010
8A-NHJ-004-010
8Z-NB8-254-010
8A-NFJ-008-010
WINDOW,FR 1M
AC CORD ASSY,E BLK SUN FAI
WINDOW,DISP H
COVER, PL M3
WINDOW,CD
47
48
49
50
51
8A-NF6-219-010
84-ZG1-245-210
87-084-077-010
8A-NH8-017-010
8A-NHJ-002-010
HLDR,FAN
CAP,OPTICAL
NYLON RIVET, 3.5-4.5
COVER, REAR STEEL H
PANEL,REAR HRJSM<HR>
17
18
19
20
21
8A-NF8-007-010
8A-NF8-005-010
8A-NF8-006-010
8A-NFJ-009-010
8A-NHJ-005-010
PANEL,LEFT V-2<HR>
PANEL,TOP<HR>
WINDOW,TOP<HR>
PANEL,TRAY
WINDOW,TRAY VCD
51
52
53
54
55
8A-NHJ-016-010
8A-NF6-217-010
8A-NF7-208-010
8A-NF7-209-010
87-NF4-221-010
PANEL,REAR HTSM<HT>
HLDR,PWB PT
HLDR,HT R
HLDR,PWB-M BTM
HLDR,CABLE
22
23
24
25
26
88-NF8-205-010
8A-NFJ-018-010
8A-NFJ-016-010
8A-NFJ-014-010
8A-NFJ-027-010
GUIDE,FL
KEY,FUN
REFLECTOR,FUN
KEY,POWER
KEY,DISC
56
57
58
A
B
87-085-185-010
8A-DJV-003-010
8A-DJV-202-010
87-067-703-010
87-NF4-224-010
BUSHING, AC CORD (E)

CABI, STEEL<HT>
HLDR, STCB<HT>
TAPPING SCREW, BVT2+3-10
S-SCREW,IT3B+3-8 CU
27
28
29
30
31
8Z-NB8-240-010
8A-NFJ-015-010
8A-NFJ-019-010
8A-NHJ-009-010
8A-NF8-203-010
COVER, PL
REFLECTOR,ECO
KEY,GEQ
KEY,ASSY OPE REV VCD
GUIDE,OPE REV
C
D
E
F
G
87-067-581-010
87-067-688-010
87-723-096-410
87-067-641-010
87-078-191-010
TAPPING SCREW, BVT2+3-15

BVTT+3-6
QT2+3-10W/O SLOT BL
UTT2+3-8(W/O SLOT)BL
S-SCREW,IT+4-10
32
33
34
35
36
8A-NF8-201-010
88-915-101-110
88-913-301-110
8A-NHJ-007-010
87-085-221-010
GUIDE,FUN
FF-CABLE, 15P 1.25 100MM
FF-CABLE,13P-1.25
KEY,CD EDIT H
FOOT,H13.5
H
I
J
K
L
87-721-097-410
87-067-689-010
87-591-095-410
87-067-001-010
87-067-584-010
QT2+3-12 GLD
BVTT+3-8
QIT+3-8
S-SCREW,BVWW ST2+3-12
BVT2+3-6 W/O SLOT
COLOR NAME TABLE

Basic color symbol
Color
Basic color symbol
Color
Basic color symbol
Color
B
Black
C
Cream
D
Orange
G
Green
H
Gray
L
Blue
LT
Transparent Blue
N
Gold
P
Pink
R
Red
S
Silver
ST
Titan Silver
T
Brown
V
Violet
W
White
WT
Transparent White
Y
Yellow
YT
Transparent Yellow
LM
Metallic Blue
LL
Light Blue
GT
Transparent Green
LD
Dark Blue
DT
Transparent Orange
GM
Metallic Green
YM
Metallic Yellow
DM
Metallic Orange
36
TAPE MECHANISM EXPLODED VIEW 1 / 1

14
B
15
B
42
A
16
51
PH(DECK 1)
RPH(DECK 2)
52
CUSH-G,DIA3.7-8-3.2
12
13
CUSH-G,DIA3.7-8-3.2
HLDR,IC
17
18
10
11
DECK C.B
50
50
49
44
41
9
7
HLDR,IC
47
43
35
41
48
19
CAPSTAN N 2.2-41.7
33
5
45
CAPSTAN N 2.2-41.5
A
20
4
HEAD 1 C.B(DECK 1)
HEAD 2 C.B(DECK 2)
34
SH,
BELT D2
22
37
36
(DECK 1)
29
31
46
21
40
32
24
(DECK 1)
(DECK 2)
39
B
25
23
26
29 (DECK 2)
38
C
27
28
30
SH,1.63-3.2-0.5 SLT
37
TAPE MECHANISM PARTS LIST 1 / 1
REF. NO. PART NO.

1
2
3
4
5
KANRI
DESCRIPTION
NO.
82-ZM3-301-610
CHAS ASSY,M2
82-ZM1-258-210
SPR-T,PINCH L
82-ZM1-341-210
LVR ASSY,PINCH L2
82-ZM1-333-210
PLATE,LINK2
82-ZM1-266-310
LVR,DIR
REF. NO. PART NO.

31
32
33
34
35
KANRI
DESCRIPTION
NO.
82-ZM1-255-310
SPR-E,LVR DIR
82-ZM3-305-210
GEAR,CAM M2
82-ZM1-227-310
LVR,TRIG
82-ZM3-306-110
LVR,FR M2
82-ZM1-265-310
SPR-E,TRIG
6
7
8
9
10
82-ZM1-214-010
82-ZM1-206-910
82-ZM3-335-310
82-ZM1-269-210
82-ZM1-219-110
SPR-T,DIR
CHAS,HEAD
PULLEY,COUPLER M3
SPR-T,BRG
SPR-T,LINK
36
37
38
39
40
82-ZM3-339-110
86-ZM1-206-010
82-ZM1-322-010
82-ZM1-220-210
82-ZM3-616-010
SHAFT,COUPLER N3
BELT,MAIN L
SPR-T,FR 60
GEAR,IDLER
RING MAGNET 4
11
12
13
14
15
82-ZM1-210-110
82-ZM1-213-010
82-ZM1-207-910
86-ZM4-206-010
82-ZM1-314-110
GEAR,H T
SPR-T,HEAD
GUIDE,TAPE
S-SCREW,AZIMUTH L
PLATE,HEAD
41
42
42
43
44
82-ZM1-216-410
87-A90-820-010
87-A90-821-010
82-ZM1-225-210
82-ZM1-226-010
GEAR,REEL
HEAD,PH HADKH25 FPC
HEAD,RPH HADKH56 FPC
GEAR,FR
GEAR,REW
16
17
18
19
20
82-ZM1-208-310
82-ZM1-218-010
82-ZM3-342-010
82-ZM1-222-210
82-ZM1-217-410
HLDR,HEAD
SPR-E,HB
BELT,SBU MOT 3
LVR,PLAY
REEL TABLE
45
46
47
47
48
82-ZM3-333-310
82-ZM1-338-110
82-ZM1-349-110
82-ZM1-348-110
82-ZM3-338-310
SLIP DISK ASSY 2

BELT,FR 4
FLY-WHL,R W
FLY-WHL,L W
FLY-WHL,R3W
21
22
23
24
25
82-ZM1-244-510
82-ZM1-285-410
82-ZM1-257-010
82-ZM1-241-310
82-ZM1-242-010
SPR-C,BT
SPR-C,BT L
SPR-T,CAS
LVR,MC
LVR,CAS
49
50
51
52
A
82-ZM3-329-410
82-ZM1-618-410
87-045-347-010
82-ZM3-221-210
85-ZM3-202-010
BELT,SBU R2
SOL ASSY,27
MOT,SHU2L 70
PULLEY,MOT 2M
S-SCREW,TG
26
27
28
29
30
82-ZM1-243-010
82-ZM1-344-010
82-ZM1-259-210
82-ZM1-240-110
80-ZM6-243-010
LVR,STOP
LVR ASSY,PINCH R2
SPR-T,PINCH R
LVR,REC(*)
SH 1.75-3.6-0.5 SLT
B
C
D
E
80-ZM6-207-010
82-ZM3-318-110
87-B10-043-010
82-ZM3-334-010
V+1.6-7
S-SCREW W,MOTOR M2
W-P,0.99-4-0.25 SLT
PW 2.16-6-0.4
38
SPEAKER DISASSEMBLY INSTRUCTIONS

Type.1
Type.4
TOOLS
Insert a flat-bladed screwdriver into the position indicated by the

arrows and remove the panel. Remove the screws of each speaker
unit and then remove the speaker units.
1 Plastic head hammer

2 (() flat head screwdriver
3 Cut chisel
How to Remove the PANEL, FR

Type.2
Remove the grill frame and four pieces of rubber caps by pulling
out with a flat-bladed screwdriver. Remove the screws from hole
where installed rubber caps. Insert a flat-bladed screwdriver into
the position indicated by the arrows and remove the panel. Remove the screws of each speaker unit and then remove the speaker
units.
1.
Insert the (() flat head screwdriver tip into the gap
between the PANEL, FR and the PANEL, SPKR. Tap the
head of the (() flat head screwdriver with the plastic
hammer head, and create the clearance as shown in Fig-1.
2.
Insert the cut chisel in the clearance, and tap the head of
the cut chisel with plastic hammer as shown in Fig-2, to
remove the PANEL, FR.
3.
Place the speaker horizontally. Tap head of the cut chisel

with plastic hammer as shown in Fig-3, and remove the
PANEL, FR completely.
Type.3
Insert a flat-bladed screwdriver into the position indicated by the
arrows and remove the panel. Turn the speaker unit to counterclockwise direction while inserting a flat-bladed screwdriver into
one of the hollows around speaker unit, and then remove the speaker
unit. After replacing the speaker unit, install it turning to clockwise
direction until "click" sound comes out.
Fig-1
Fig-2
Fig-3
How to Attach the PANEL, FR

Attach the PANEL, FR to the PANEL, SPKR. Tap the four
corners of the PANEL, FR with the plastic hammer to fit the
PANEL, FR into the PANEL, SPKR completely.
39
SPEAKER PARTS LIST

SX-WNBL53 (YSL, YJSL, YJ3SL, YJ7SL, YSK1BL)
REF. NO. PART NO.
1
1
2
3
3
8A-NS5-001-010
8A-NS5-016-010
8A-NS5-004-010
8A-NS5-005-010
8A-NS5-012-010
KANRI
DESCRIPTION
NO.
PANEL,FR<EXCEPT YSL>
PANEL,FR U<YSL>
PANEL,DUCT
GRILLE,FRAME ASSY<EXCEPT YSL>
GRILLE,FRAME ASSY U<YSL>
4
5
6
7
8
8A-NS5-009-010
88-NS5-610-010
88-NS5-611-010
8Z-NSY-003-010
88-NS3-029-010
PROTECTOR
CORD,SPKR
CORD,SPKR B/L
CORD,BUSH
CORD,BUSH L<EXCEPT YSK1BL>
9
10
10
11
12
8Z-NS7-602-010
8A-NS8-604-010
8A-NS5-604-010
8Z-NSY-608-010
8Z-NS6-021-010
SPKR,W 160
SPKR,M 100<EXCEPT YSK1BL>
SPKR,M 100<YSK1BL>
SPKR, CERAMIC ASSY
FOOT<YSK1BL>
13
14
15
8A-NS8-013-010
8Z-NS8-174-010
8A-NS5-017-010
FASTNER,C<YSK1BL>
UT1 4*14 BZN<YSK1BL>
PLATE,NAME B<EXCEPT YSK1BL>
ACCESSORIES / PACKAGE LIST

REF. NO.
PART NO.
1
2
3
4
5
KANRI
NO.
8A-NHJ-901-010
87-006-226-010
87-043-115-010
87-050-103-010
87-A90-119-010
DESCRIPTION
IB,H(EC-H)M VC58
AM LOOP ANT C0
ANT,FEEDER FM
CORD,PIN 1PY1.5M
ANT WIRE SW(5M)
6
7
87-A91-017-010
8Z-NH8-702-010
PLUG,CONVERSION JT-0476
RC UNIT,RC-ZAS07
40
211, IKENOHATA 1CHOME, TAITO-KU, TOKYO 110, JAPAN TEL:03 (3827) 3111
9820543 0251431
Printed in Singapore

Aiwa NSX-VC58

Uploaded by

Copyright:

Available Formats

Aiwa NSX-VC58

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Aiwa NSX-VC58

Uploaded by

Copyright:

Available Formats

NSX-VC58

BASIC TAPE MECHANISM : 2ZM-3MK2 PR4NM

This Service Manual is the Revision Publishing and replaces Simple

S/M Code No. 09-006-432-0R1

If requiring information about the CD mechanism, see Service Manual

87.5 MHz to 108 MHz

531 kHz to 1602 kHz (9 kHz step)

<SW tuner section>

5.730 MHz to 17.900 MHz

4 tracks, 2 channels stereo

<Compact disc player section>

120 V/220-230 V/240 V AC

Design and specifications are subject to change without notice.

PROTECTION OF EYES FROM LASER BEAM DURING SERVICING

Caution: Invisible laser radiation when

Usynlig laserstling ved bning, nr sikkerhedsafbrydereer

Precaution to replace Optical block

1) After the connection, remove solder shown in

NOTE ON BEFORE STARTING REPAIR

1 Remove the AC power cord.

Select a discharging resistor referring to the following table.

Charging voltage (V)

Rated power (W)

2. Check items before exchanging the MICROCOMPUTER

2-1. Regarding the HOLD terminal of the MICROCOMPUTER

Good or no good judgement of the MICROCOMPUTER

2-2. Regarding reset

2-3. Confirmation of soldering state of MICROCOMPUTER

ELETRICAL MAIN PARTS LIST

CAP, ELECT 22-50

CAP, ELECT 0.33-50V

CAP,E 330-6.3 SME

CAP, ELECT 1-50V

CAP, CHIP 0.01-25 K B

CAP,E 100-10 M 11L SME

CAP, ELECT 10-50V

C-CAP,S 820P-50 J SL C2012

CAP, CHIP 0.022

CAP,E 10-50 M 11L SME

CAP, ELECT 0.47-50V

CAP, ELECT 1-50V

CAP, CHIP 0.01 DM

CAP,E 0.47-50 M 11L SME

C-CAP,S 2200P-50 K B C2012

CHIP CAP 1000P

CHIP CAP 1000P

CAP,E 10-16 GAS

CONN ASSY,3P (VM) ANF-6

JACK,DIA6.3 BLK ST W/S KM

CAP,E 22-25 M SRE

CAP, CHIP 0.022

COIL,OSC SW-2N (COI)

TRIMMER,CER 20P 4.0X4.5 ECR

FILTER, EMI BL OIRNI

CONN,13P H BLK TAC-L13P-A3

CAP, ELECT 10-50V

C-CAP,S 6800P-50 K B C2012

CAP CHIP S5600P

CAP,E 470-25 SME