Scribd Logo
Upload

Welcome to Scribd!

  • 479 views

    10.3-Pipe Head Loss

    Uploaded by

    Farooq Bhutta
    This section presents the darcy-weisbach equation. It is used for calculating head loss in a straight run of pipe. Pipe Head Loss is one type of head loss; the other type is called component head loss.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd

    10.3-Pipe Head Loss

    Uploaded by

    Farooq Bhutta
    479 views3 pages
    This section presents the darcy-weisbach equation. It is used for calculating head loss in a straight run of pipe. Pipe Head Loss is one type of head loss; the other type is called component head loss.

    Copyright

    © Attribution Non-Commercial (BY-NC)

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This section presents the darcy-weisbach equation. It is used for calculating head loss in a straight run of pipe. Pipe Head Loss is one type of head loss; the other type is called component head loss.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    479 views3 pages

    10.3-Pipe Head Loss

    Uploaded by

    Farooq Bhutta
    This section presents the darcy-weisbach equation. It is used for calculating head loss in a straight run of pipe. Pipe Head Loss is one type of head loss; the other type is called component head loss.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 3

    Pipe Head Loss

    http://edugen.wiley.com/edugen/courses/crs2436/crowe9771/crowe9771...

    10.3 Pipe Head Loss


    This section presents the Darcy-Weisbach equation, which is used for calculating head loss in a straight run of pipe. This equation is one of the most useful equations in fluid mechanics.

    Combined (Total) Head Loss


    Pipe head loss is one type of head loss; the other type is called component head loss. All head loss is classified using these two categories: (10.4)

    Component head loss is associated with flow through devices such as valves, bends, and tees. Pipe head loss is associated with fully developed flow in conduits, and it is caused by shear stresses that act on the flowing fluid. Note that pipe head loss is sometimes called major head loss, and component head loss is sometimes called minor head loss. Pipe head loss is predicted with the Darcy-Weisbach equation.

    Derivation of the Darcy-Weisbach Equation


    To derive the Darcy-Weisbach equation, start with the situation shown in Fig. 10.4. Assume fully developed and steady flow in a round tube of constant diameter D. Situate a cylindrical control volume of diameter D and length L inside the pipe. Define a coordinate system with an axial coordinate in the streamwise direction (s direction) and a radial coordinate in the r direction.

    Figure 10.4 Initial situation for the derivation of the Darcy-Weisbach equation. Apply the momentum equation (6.5) to the control volume shown in Fig. 10.4. (10.5)

    1 of 3

    1/15/2009 12:59 AM

    Pipe Head Loss

    http://edugen.wiley.com/edugen/courses/crs2436/crowe9771/crowe9771...

    Select the streamwise direction and analyze each of the three terms in Eq. (10.5). The net efflux of momentum is zero because the velocity distribution at section 2 is identical to the velocity distribution at section 1. The momentum accumulation term is also zero because the flow is steady. Thus, Eq. (10.5) simplifies to F = 0. Forces are shown in Fig. 10.5. Summing of forces in the streamwise direction gives (10.6)

    Figure 10.5 Force diagram. Figure 10.4b shows that sin = (z/L). Equation (10.6) becomes (10.7) Next, apply the energy equation 7.29 to the control volume shown in Fig. 10.4. Recognize that hp = ht = 0, V1 = V2, and 1 = 2. Thus, the energy equation reduces to (10.8)

    Combine Eqs. (10.7) and (10.8) and replace L by L. Also, introduce a new symbol hf to represent head loss in pipe. (10.9)

    Rearrange the right side of Eq. (10.9). (10.10) Define a new -group called the friction factor f that gives the ratio of wall shear stress (o) to kinetic pressure (V2/2): (10.11)

    In the technical literature, the friction factor is identified by several different labels that are synonymous: friction factor, Darcy friction factor, Darcy-Weisbach friction factor, and the resistance coefficient. There is also another coefficient called the Fanning friction factor, often used by chemical engineers, which is related to the DarcyWeisbach friction factor by a factor of 4.

    2 of 3

    1/15/2009 12:59 AM

    Pipe Head Loss

    http://edugen.wiley.com/edugen/courses/crs2436/crowe9771/crowe9771...

    This text uses only the Darcy-Weisbach friction factor. Combining Eqs. (10.10) and (10.11) gives the DarceyWeisbach equation: (10.12) To use the Darcy-Weisbach equation, the flow should be fully developed and steady. The Darcy-Weisbach equation is used for either laminar flow or turbulent flow and for either round pipes or nonround conduits such as a rectangular duct. The Darcy-Weisbach equation shows that head loss depends on the friction factor, the pipe-length-to-diameter ratio, and the mean velocity squared. The key to using the Darcy-Weisbach equation is calculating a value of the friction factor f. This topic is addressed in the next sections of this text.

    Copyright 2009 John Wiley & Sons, Inc. All rights reserved.

    3 of 3

    1/15/2009 12:59 AM

    You might also like