SPX DC Power
Uploaded by
Central HydraulicsSPX DC Power
Uploaded by
Central HydraulicsDC-10SF
12V DC MANUAL OPERATED POWER UP/GRAVITY DOWN
This unit is for power up-hold-gravity down applications. In one direction the manual handle starts unit to power up. In the other direction, the manual handle provides gravity down. In the neutral position, the unit holds steady. The unit features an adjustable relief valve, cartridge hold & lower valves, allowing for easy field service & interchangeability. A pressure compensated flow control for lower function is optional.
96
* Substitute KN10 for metric
WWW.STONEHYDRAULICS.COM
12V DC MATERIAL HANDLING SOLENOID OPERATED POWER UP/GRAVITY DOWN
DC-20MH
Designed for low-lift pallet trucks. The units have a 3-way circuit for raise-hold-lower functions & are used with a single acting cylinder. This unit is plumbed for vertical mounting & is interchangeable with other manufacturers power packs.
111
DC-20ML
12V DC MAN LIFT SOLENOID OPERATED POWER UP/GRAVITY DOWN
Designed for use on battery operated, elevated work platforms using a raise-hold & gravity lower circuit. Includes: Normally open valve to protect operators from run-on Manual override to allow the platform to be lowered in case of power failure.
112
WWW.STONEHYDRAULICS.COM
12V DC SOLENOID OPERATED POWER UP/GRAVITY DOWN
DC-20SF
This unit is for power up-hold-gravity down applications. The remote controller allows an operator to power up & gravity down the unit. In the off position, the unit holds steady. The unit features an adjustable relief valve, cartridge hold & lower valves, allowing for easy field service & interchangeability. A pressure compensated flow control for lower function is optional.
* Substitute KN10 for metric
97
24V DC MATERIAL HANDLING SOLENOID OPERATED POWER UP/GRAVITY DOWN
DC-24MH
Designed for low-lift pallet trucks. The units have a 3- way circuit for raise-hold-lower functions & are used with a single acting cylinder. This unit is plumbed for vertical mounting & is interchangeable with other manufacturers power packs.
113
DC-30APU
1 2 V D C A U X I L I A RY P O W E R U N I T RELIEF & CHECK VALVE ONLY
Intended to be used with remote directional control valving & reservoir. This unit has an adjustable relief valve & outlet check valve. For applications such as back-up hydraulic power for truck mounted/mobile equipment. It can also be used to power material handling functions & other intermittent duty applications.
114
WWW.STONEHYDRAULICS.COM
DC-30SF
12V DC CHECK & RELIEF VALVE POWER UNIT
This unit provides flow & pressure for customer specific applications. The unit can be used for power uphold-gravity down, or power up-hold-power down applications, dependent on customer-supplied valving. Features include an adjustable relief valve & cartridge check valve.
* Substitute KN10 for metric
98
WWW.STONEHYDRAULICS.COM
12V DC SOLENOID OPERATED POWER UP/POWER DOWN
This unit is for power up-hold-power down applications. The controller (either customer-supplied or supplied with unit) will power the unit in both directions. The unit will hold load in the off position. Pressure compensated flow control allows smooth-running functions in both directions. Features include an adjustable relief valve & cartridge valves for easy field service & interchangeability.
D C- 41D T
22.69" [576.3mm]
13.62" [345.7mm] Shown with 2 Gal. Reservoir
1.44" [36.5mm]
6.70" [170.2mm]
ORDERING GUIDE
Fixed Low Relief Fixed High Relief
Blank C
No Controller With Controller
16 20 25 31
10P 10S 15P 15S 20P 20S
1 = 100 PSI (6.9 Bar) 3 = 300 PSI (20.6 Bar) 5 = 500 PSI (34.4 Bar 8 = 800 PSI (55 Bar)
2.50" [63.5mm]
7.71" [195.9mm]
20 = 2000 PSI (137.6 Bar) 25 = 2500 PSI (172 Bar) 30 = 3000 PSI (206.4 Bar) 35 = 3500 PSI (240.9 Bar) High Relief can be set from 2000 - 3500 PSI in increments of 100
Example listing: DC-41DTC-20-15P-5-20
Standard Features on DC-41DT family: 12V DC 1 Terminal Std Duty Motor 12V DC Int Duty Start Solenoid 10V DC 2P4W direction valving 10V DC 2P2W load hold valve 2.5 GPM Flow control Horizontal mount plumbing SAE Ports
Example: 25 = 2.5 CC/Rev. (.153 Cu. In/Rev.)
25P 25S 30P 30S
Low Relief can be set from 100 - 800 PSI in increments of 100
Example: 10P = 1 Gal. Plastic 25S = 2.5 Gal. Steel
DC-41DT
KMD1 Plug Battery Cable Low PSI Relief Kit T1-1019-05 1967-AB K-424
A Port
KP25
B Port
5310-AC High PSI Relief Valve Kit K-425 K-420 FC-2.5 3832-AC * Will vary depending on model selection. DC-41DTC only Flow Control
99
DC-50SF
12V DC MANUAL OPERATED POWER UP/POWER DOWN
This unit is for power up-hold-power down applications. The manually operated directional valve powers the unit in both directions. In the neutral position the unit is off & holds steady. Features include an adjustable relief valve & load-holding P.O. check valve.
* Substitute KN10 for metric
100
WWW.STONEHYDRAULICS.COM
12V DC SOLENOID OPERATED POWER UP/POWER DOWN
DC-60SF
This unit is for power up-hold-power down applications. The controller allows an operator to power the unit in both directions. In the off position, the unit holds steady. Features include an adjustable relief valve & load-holding P.O. check valve.
* Substitute KN10 for metric
** Older Endheads May Use M8 (Metric) Bolts Stone P/N 2825-AA
101
DC-62SF
12V DC SOLENOID OPERATED DUAL POWER UP/POWER DOWN
This unit is for dual power up-hold-power down applications. The customer-supplied controller will power the unit in both directions. In the off position, the unit holds steady. Directional valves run independently of each other, allowing for two separate system functions. Features include an adjustable relief valve & loadholding P.O. check valve.
* Substitute KN10 for metric
102
WWW.STONEHYDRAULICS.COM
12V DC BALE SPIKE SOLENOID OPERATED POWER UP/POWER DOWN
DC-70BS
Designed primarily to operate tines which pick up round bales. Incorporates a 2 position, 4-way cartridge valve & double pilot-operated checks to control a double acting cylinder, to lift-hold-lower the bale.
115
12V DC SOLENOID OPERATED POWER UP/POWER DOWN
DC-70SF
This unit is for power up-hold-power down applications. The controller allows an operator to power the unit in both directions. In the off position, the unit holds steady. Features include an adjustable relief valve & load-holding P.O. check valves. A cartridge directional valve is also included, for easy field service & interchangeability.
* Substitute KN10 for metric
** Older Endheads May Use M8 (Metric) Bolts Stone P/N 2825-AA
103
DC-80SP
12V DC SNOW PLOW SOLENOID OPERATED POWER ANGLE & LIFT/GRAVITY DOWN
Designed to operate all functions of a power operated angling snow plow. The unit includes a lift-holdgravity lower function for the blade, with a continuous "float" capability. A directional valve controls power angling of the blade, 2 cross-over reliefs protect the system from damage should the blade be obstructed while plowing.
116
WWW.STONEHYDRAULICS.COM
DC-90SF
12V DC RELIEF VALVE ONLY
This unit provides flow & pressure for customer specific applications. The unit can be used on double acting applications. Features include an adjustable relief valve.
* Substitute KN10 for metric
104
WWW.STONEHYDRAULICS.COM
