Write a program to led with button.
1. Push button – Led on
2. Push button – led off
Code:
int led=11;
int btn=10;
int BUTTONstate=0;
void setup() {
pinMode(btn, INPUT);
pinMode(led, OUTPUT);
}
void loop() {
BUTTONstate=digitalRead(btn);
if(BUTTONstate==HIGH)
{
digitalWrite(led, HIGH);
}
BUTTONstate=digitalRead(btn);
if(BUTTONstate==HIGH)
{
digitalWrite(led, LOW);
}
}
Just a simple slide-switch demo
void setup() {
pinMode(LED_BUILTIN, OUTPUT);
pinMode(5, INPUT_PULLUP);
}
void loop() {
digitalWrite(LED_BUILTIN, digitalRead((5)));
}
Buzzer with led light
int b=13;
int led=8;
void setup() {
pinMode(b,OUTPUT);
pinMode(led,OUTPUT);
void loop() {
tone(b,1000);
digitalWrite(led , HIGH);
delay(1000);
noTone(b);
digitalWrite(led, LOW);
delay(1000);
}
Simple button with led
int led=9;
int btn=8;
void setup() {
pinMode(9, OUTPUT);
pinMode(8, INPUT);
}
void loop() {
if (digitalRead(8)==1){
digitalWrite(9, HIGH);
}
else{
digitalWrite(9, LOW);
}
}
RGB LED LIGHT
int Rled=13;
int Gled=12;
Common Pin= Cathode
int Bled=11;
void setup() {
pinMode (Rled,OUTPUT);
pinMode (Gled,OUTPUT);
pinMode (Bled,OUTPUT);
}
void loop() {
digitalWrite (Rled,HIGH);
delay (1000);
digitalWrite (Rled,LOW);
digitalWrite (Gled,HIGH);
delay(1000);
digitalWrite (Gled,LOW);
digitalWrite (Bled,HIGH);
delay(1000);
digitalWrite (Bled,LOW);
delay (1000);
}
Interfacing RGB Led with Arduino
int redPin= 5; Common Pin= Cathode
int greenPin = 6;
int bluePin = 7;
void setup() {
pinMode(redPin, OUTPUT);
pinMode(greenPin, OUTPUT);
pinMode(bluePin, OUTPUT);
}
void loop() {
setColor(255, 0, 0); // Red Color
delay(1000);
setColor(0, 255, 0); // Green Color
delay(1000);
setColor(0, 0, 255); // Blue Color
delay(1000);
setColor(255, 255, 255); // White Color
delay(1000);
setColor(170, 0, 255); // Purple Color
delay(1000);
setColor(127, 127, 127); // Light Blue
delay(1000);
}
void setColor(int redValue, int greenValue, int blueValue) {
analogWrite(redPin, redValue);
analogWrite(greenPin, greenValue);
analogWrite(bluePin, blueValue);
}
MQ135 GAS SENSOR
int sensorValue;
int digitalValue;
void setup()
{
Serial.begin(9600); // sets the serial port to 9600
pinMode(13, OUTPUT);
pinMode(2, INPUT);
}
void loop()
{
sensorValue = analogRead(0); // read analog input pin 0
digitalValue = digitalRead(2);
if (sensorValue > 400)
{
digitalWrite(13, HIGH);
}
else
digitalWrite(13, LOW);
Serial.println(sensorValue, DEC); // prints the value read
Serial.println(digitalValue, DEC);
delay(1000); // wait 100ms for next reading
}
SERVO MOTOR
#include <Servo.h>
Servo myServo; // Create servo object
void setup() {
myServo.attach(11); // Attach to pin D9
void loop() {
// Sweep from 0 to 180 degrees
for (int pos = 0; pos <= 180; pos++) {
myServo.write(pos); // Move to position
delay(15); // Wait for servo to reach position
// Sweep back from 180 to 0 degrees
for (int pos = 180; pos >= 0; pos--) {
myServo.write(pos);
delay(15);
}
LDR SENSOR WITH A LED LIGHT
const int ldrPin = A0; // LDR connected to analog pin A0
const int ledPin = 13; // LED connected to digital pin 13
int ldrValue = 0; // Store LDR reading
void setup() {
pinMode(ledPin, OUTPUT);
Serial.begin(9600); // For debugging
void loop() {
ldrValue = analogRead(ldrPin); // Read light level
Serial.println(ldrValue); // Print to Serial Monitor
if (ldrValue < 400) { // Adjust this threshold based on your lighting
digitalWrite(ledPin, HIGH); // Turn on LED when it's dark
} else {
digitalWrite(ledPin, LOW); // Turn off LED when it's bright
delay(500); // Wait a bit before next reading
