ITU Maritime Mobile 1
ITU Maritime Mobile 1
ITU Maritime Mobile 1
Manual
Volume 1
English edition 2011
Radiocommunication Bureau
I n t e r n a t i o n a l
Te l e c o m m u n i c a t i o n
U n i o n
Manual
for use by the Maritime Mobile and Maritime Mobile-Satellite Services
Provisions of the Telecommunication Services applicable or useful to stations in the Maritime Mobile and Maritime Mobile-Satellite Services
Volume 1
English edition 2011
Radiocommunication Bureau
Placing orders for ITU publications Please note that orders cannot be taken over the telephone. They should be sent by fax or e-mail. ITU Sales and Marketing Division Place des Nations CH -1211 Geneva 20 Switzerland Fax: E-mail: +41 22 730 5194 [email protected]
ITU 2011
All rights reserved. No part of this publication may be reproduced, by any means whatsoever, without the prior written permission of ITU.
Acknowledgements
iii
ACKNOWLEDGEMENTS
Several photos and illustrations in this publication were kindly made available by the International Maritime Organization, Cospas-Sarsat, the International Radio-Maritime Committee, Inmarsat, UK Maritime and Coastguard Agency, Ofcom, United States Coastguard and BP Shipping.
Table of Contents
TABLE OF CONTENTS
Page Acknowledgements .................................................................................................. Preamble ................................................................................................................. Foreword ................................................................................................................. 1 2 Introduction .................................................................................................. System overview of the GMDSS ................................................................. 2.1 2.2 2.3 2.4 3 3.1 3.2 3.3 4 4.1 4.2 4.3 4.4 4.5 4.6 5 5.1 5.2 5.3 5.4 5.5 5.6 Principles of distress alerting ............................................................ Communication services ................................................................... Provision of Maritime Safety Information ........................................ Main sub-systems of the GMDSS ..................................................... International Telecommunication Union ........................................... International Maritime Organization ................................................. Administrations and national authorities ........................................... General provisions ............................................................................. Functional requirements .................................................................... SOLAS carriage requirements........................................................... Maintenance requirements ................................................................ Other carriage requirements .............................................................. Carriage of equipment by other ships ................................................ Radiotelephony.................................................................................. Digital selective-calling system......................................................... Inmarsat ............................................................................................. NAVTEX .......................................................................................... Cospas-Sarsat .................................................................................... Radar Search and Rescue Transponder ............................................. iii vii ix 1 2 2 6 8 11 12 12 15 17 18 18 20 22 22 25 25 28 28 31 34 40 44 49
vi
Maritime Manual
Page 6 Operational procedures for distress, urgency and safety communications .. 6.1 Distress alerting and distress calling ................................................. 6.2 Cancellation of an inadvertent distress alert ...................................... 6.3 Urgency and safety communications................................................. The use of frequencies ................................................................................. 7.1 Basic considerations on the use of frequencies ................................. 7.2 Frequencies for the GMDSS and watch-keeping .............................. 7.3 Use of frequencies for general communications ............................... Radio personnel requirements ...................................................................... 8.1 Authority of the master...................................................................... 8.2 Operators certificates ....................................................................... 8.3 Personnel ........................................................................................... Identification of stations ............................................................................... 9.1 Formation and use of call signs and MMSI....................................... 9.2 Table of allocation of international call sign series ........................... 9.3 Table of allocation of Maritime Identification Digits ....................... Other administrative and operational procedures......................................... 10.1 Priority of communications ............................................................... 10.2 Inspection of stations ......................................................................... 10.3 Working hours of stations ................................................................. 10.4 Interferences ...................................................................................... 10.5 Secrecy .............................................................................................. 10.6 Documents to be carried onboard ship .............................................. 10.7 Phonetic alphabet and figure code ..................................................... Related publications ..................................................................................... 11.1 ITU publications ................................................................................ 11.2 IMO publications............................................................................... 51 51 59 61 63 63 65 69 75 75 75 76 77 77 79 79 80 80 80 81 82 82 84 85 87 87 89 92 98 100 109 116
10
11
Annex 1 Terms and definitions ............................................................................. Annex 2 Technical characteristics of stations ....................................................... Annex 3 Table of allocation of international call sign series ................................ Annex 4 Table of allocation of Maritime Identification Digits ............................. Annex 5 List of Abbreviations and Glossary ........................................................
Preamble
vii
PREAMBLE
The main purpose of the Manual for Use by the Maritime Mobile and Maritime Mobile-Satellite Services has been to provide the maritime community with a compilation of the most relevant ITU treaty texts, ITU regulatory texts and ITU technical and operational texts that are relevant to the maritime mobile and maritime mobile-satellite services, so that the concerned persons could have ready reference to these texts in the application of the relevant radiocommunication procedures. The requirement for providing ship stations with the Maritime Manual was introduced into the Radio Regulations in 1979 following an earlier requirement, dating back to 1927, for providing the Radio Regulations and the Convention, onboard ship. The form of the Manual and its contents and periodicity is determined by the Radiocommunication Bureau in consultation with administrations and international organizations concerned and revised versions have been published following each new edition of the Radio Regulations. The changing requirements after the introduction of the GMDSS regarding the personnel onboard ship however, has resulted in a situation where some of the texts included in the Manual have become very complex for the maritime personnel. In order to improve its practical utility a new kind of Handbook describing the GMDSS and/or other maritime operational procedures in a tutorial manner, rather than a compilation of complex technical texts has been prepared. In this context, the Radiocommunication Bureau consulted the maritime community with a questionnaire which led to further discussion at the World Radiocommunication Conference 2007 (WRC-07). The decisions of the Conference were recorded in Resolution 355 (Content, formats and periodicity of the maritime-related service publications) which, with regard to the Manual, invited the ITU-R to conduct studies with a view to developing a practiceoriented and user-friendly format of the Manual and to periodically update the text to cover the latest developments, and to complete these studies by 31 December 2010. In line with these decisions, the Radiocommunication Bureau prepared a new structure giving extended and modified scope to the publication in cooperation with ITU-R Working Party 5B and IMO resulting in a concept of a Manual in two volumes: Volume 1 to give practical information; Volume 2 to contain the regulatory texts of the existing Manual.
Foreword
ix
FOREWORD
This first edition of the new Volume 1 of the Manual for use by the Maritime Mobile and Maritime Mobile-Satellite Services is published in accordance with Article 20 (No. 20.14) of the Radio Regulations, and results from studies carried out in the ITU-R during 2008 and 2009. Volume 1 complements Volume 2 of the Manual by providing descriptive text of the organisation and operation of the GMDSS and other maritime operational procedures. Volume 2 contains extracts of the regulatory texts associated with maritime operations. This Volume contains the following chapters: Page 1 2 3 4 5 6 7 8 9 10 11 Introduction .................................................................................................... System overview of the GMDSS ................................................................... The scope of activities and responsibilities .................................................... General rules of the GMDSS ......................................................................... Radio procedures ............................................................................................ Operational procedures for distress, urgency and safety communications .... The use of frequencies.................................................................................... Radio personnel requirements ........................................................................ Identification of stations ................................................................................. Other administrative and operational procedures ........................................... Related publications ....................................................................................... 1 2 12 18 28 51 63 75 77 80 87
Annexes are also provided to describe: Terms and definitions, Technical characteristics of stations, Table of allocation of international call sign series, Table of allocation of Maritime Identification Digits and List of Abbreviations and Glossary.
Maritime Manual
Introduction
Communication with ships was the first application of radio at the end of the nineteenth century. Ships started fitting radio installations for the purpose of improving the business of the ship and gradually these installations came to be used also for distress and safety purposes. With an increasing number of ships using radio, the need for technical standards and common operating procedures became important together with a need to regulate the use of the frequencies. This all led to the development of the Radio Regulations in 1906 which today are maintained by the radiocommunication sector of the International Telecommunication Union (ITU). The distress and safety system was developed for the larger commercial ships and relied on the use of Morse radiotelegraphy on 500 kHz, together with the later additions of radiotelephony on 2 182 kHz and 156.8 MHz (VHF channel 16). As the technology advanced, it became practicable to fit radio to smaller and smaller ships, so that by the latter part of the twentieth century it had become a requirement for most commercial ships to carry radio for distress and safety purposes. These requirements are laid down in the International Convention for the Safety of Life at Sea (SOLAS) which is maintained by another United Nations specialized agency, the International Maritime Organization (IMO). A description of the organizations involved is given in Chapter 3. Other ships, which are not legally subject to the regulation of the SOLAS Convention, gradually began to carry radio either by national or regional requirements or voluntarily. Today these ships are by far the majority users of maritime radio. The Global Maritime Distress and Safety System (GMDSS) derived from studies carried out in the ITU and IMO starting in the mid-1970s. These led to quite a different system from that used hitherto. The previous system had been ship-to-ship. It relied on a ship in distress being able to contact another ship that could assist which in turn required aural watch-keeping on ships and skilled personnel (often a dedicated radio officer) to handle the communications. The new system was ship-to-shore, enabling a degree of automation on the ship with less skilled operators. This did, however, result in a new need for skilled operators on shore operating in a global search and rescue network. IMO subsequently devoted considerable effort into organising its member states to achieve this. The ITU established the appropriate regulatory framework for the implementation of the GMDSS through the 1983 and 1987 World Administrative Radio Conferences for the Mobile Services (WARC Mob-83 and -87) which adopted amendments to the ITU Radio Regulations prescribing frequencies, operational procedures and radio personnel for the GMDSS. A further change with the new system was that it applied not only to ships but also to persons in distress. An overview of the GMDSS is given in Chapter 2 and its general rules in Chapter 4. The ships subject to the SOLAS Convention converted to the new system in the period between 1992 and 1999.
Maritime Manual
Communications with ships is achieved with a mobile radiocommunication service as defined by the ITU (definitions are given in Annex 1). The Radio Regulations specify certain bands which are reserved for the mobile service. A few parts of these bands are further reserved for use by maritime communications only and they are referred to as bands for the maritime mobile service. Similarly, if satellite communications are involved the service is known as the mobilesatellite service and the maritime mobile-satellite service. The use of the frequencies in these services is described in Chapter 7. The Radio Regulations are maintained by World Radiocommunication Conferences and the most recent Conference held in 2007 (WRC-07) achieved a complete revision of the operational procedures for distress, urgency and safety communications. These operational procedures are described in Chapter 6 and the operation of the equipment carried on the ships is described in Chapter 5. The Radio Regulations, which are binding on the member administrations of the ITU, provide the regulatory framework for the use of the radio spectrum. The other Chapters of this Volume describe the relevant regulatory provisions employed with maritime operations. Volume 2 of the Manual includes the relevant texts of the Articles and Appendices of the Radio Regulations related to maritime issues.
2
2.1
The GMDSS includes a ship-to-ship component using VHF radio with digital selective-calling (DSC) but for distress alerting it is fundamentally a ship-to-shore system. Ships carry equipment which enables them to transmit ship-to-shore distress alerts. Ships equipped according to SOLAS Chapter IV additionally carry equipment which enables them to transmit ship-to-shore distress alerts by two separate and independent means, each using a different radiocommunication service. The distress alerts when received on shore are routed to a rescue co-ordination centre (RCC). The function of the RCC is to transmit a distress acknowledgement which indicates that it has accepted responsibility for the incident. The RCC will then relay the distress alert back to the area of the distress in order to raise contact with ships in the area which may be able to assist as shown in Fig. 1.
Maritime Manual
RCC relays the alert to ships in the area that may be able to assist
Maritime-01
It is a requirement of SOLAS Chapter V that a master of a ship receiving a signal that persons are in distress at sea proceeds to their assistance with all speed. Alternatively, the RCC (see Fig. 2) may be able to deploy search and rescue vehicles of its own or from a cooperating state. The arrangements for the provision of search and rescue services are given in the IMO International Convention on Maritime Search and Rescue (SAR Convention). Parties to the Convention are required to establish and agree search and rescue regions. IMO has divided the world into SAR areas and invited Member States to cooperate with arrangements so that SAR services will be available when needed. The detail is maintained in the IMO Global Maritime Search and Rescue (SAR) Plan (Published by IMO in a series of SAR Circulars) and a top level overview is shown in Fig. 3.
Maritime Manual
FIGURE 2 Two views of the RCC at Riga in Latvia showing the building and an operator on watch
Maritime-02
FIGURE 3 Global Maritime Search and Rescue areas. At this scale only the larger areas are shown. Full details of the smaller areas are given in the IMO SAR plan . Description of A1 and A2 sea areas is given on page 7.
Maritime Manual
Coast lines where A1 or A2 sea areas are provided Search and Rescue Region boundary
Maritime-03
Maritime Manual
2.2
Communication services
There are satellite communications and terrestrial communications available for use in the GMDSS. At the present time, satellite services which include distress alerting are provided by Inmarsat (a commercial non-government company) and Cospas-Sarsat (a multi-national government-funded organization). Inmarsat provides two-way communications to ships globally except for the polar regions (these are largely not navigable by ships). Cospas-Sarsat provides complete global coverage but with a system that is limited to the reception of signals from emergency position-indicating radiobeacons (EPIRBs) there are no facilities for other communication or for transmission of signals to ships. Terrestrial services (see Fig. 4) are provided by some administrations. They may be long range which use high frequencies (HF) in the bands 4, 6, 8, 12 and 16 MHz as well as 18, 22 and 25 MHz for DSC and radiotelephony which can provide global coverage.
FIGURE 4 Terrestrial communications require the provision of base stations about every 30 nautical miles (see Note 1) for VHF and 150 nautical miles for MF. The figure shows modem equipment which is used to convey the radio signals over cables to remote base station sites and an antenna tower. Antenna towers can sometimes be shared with other services, in this case with cellular telephone in Lindi, Tanzania
Maritime-04
Maritime Manual
Radiotelex narrow-band direct-printing (NBDP) services may also be provided but the use of NBDP is declining. Terrestrial services may be provided at a medium range using MF 2 187.5 kHz for DSC and 2 182 kHz for radiotelephony, or a short range using VHF 156.525 MHz (channel 70) for DSC and 156.8 MHz (channel 16) for radiotelephony. The operational and personnel requirements for maritime radiocommunications are described in the GMDSS by referring to four communication sea areas (see Fig. 5), viz.: A1 An area within the radiotelephone coverage of at least one VHF coast station in which continuous DSC alerting is available. Such an area extends typically 20 30 nautical miles from the coast station. An area, excluding sea area A1, within the radiotelephone coverage of at least one MF coast station in which continuous DSC alerting is available. For planning purposes this area typically extends up to 100 nautical miles offshore, but would exclude any A1 designated areas. In practice, satisfactory coverage may often be achieved out to around 400 nautical miles offshore. An area, excluding sea areas A1 and A2, within the coverage of an Inmarsat geostationary satellite in which continuous alerting is available. This area lies between about latitudes 76o north and south, but excludes A1 and/or A2 designated areas. An area outside sea areas A1, A2 and A3. This is essentially the polar regions, north and south of about 76o of latitude, but excludes any other areas.
A2
A3
A4
The details of the sea areas are given in the IMO GMDSS Master Plan (Published by IMO in a series of GMDSS Circulars). All oceans are covered by HF services for which the IMO requirement is to have two coast stations per ocean region. Not all coastlines are provided with A1 or A2 sea areas (see Fig. 3) and ships trading along those may need to be equipped with satellite communication equipment. Satellite communication equipment was an expensive option in the early days of the implementation of the GMDSS, but now virtually all commercial ships are fitted with satellite terminals due to other IMO requirements for a Ship Security Alert System and Long-Range Identification and Tracking.
Maritime Manual
60
100 0 100 200
A1 002311000
Thorshavn
A2
Flore 002570500 Shetland 002320001 Tjome 0025701 Rogaland 002270300
A3
Stornoway 002820024 Aberdeen 002320004 Forth 002320005
55 Malin Head 002500100 Belfast 002320021 Dublin 002500300 Valentia 002500200 50 Clyde 002320022
Skagen 002191000
A2
Blavand 002191000
Holyhead 002320018
Liverpool 002320019
Swansea 002320016 Themes Solent 002320009 002320011 Brinham Dover 002320013 Oostende 002050480 002320010 Portland Falmouth Gris Nez 002320012 002320014 002275100 Jobourg 002275200 Medium frequency (MF) and Milford Haven 002320017
A2
very high frequency (VHF) coast radio station Very high frequency (VHF) coast radio station
10
2.3
The GMDSS includes an internationally and nationally coordinated network of broadcasts containing information which is necessary for safe navigation. This information can be received by ships using equipment which automatically monitors the
Maritime Manual
appropriate transmissions, displays information which is relevant to the ship and provides a print capability. This concept is illustrated in Fig. 6.
FIGURE 6 The maritime safety information service
INFORMATION SERVICES
Navigational Warning
Meteorological Information
SAR Information
Sub-Area
NAVAREA/ METAREA
NAVTEX
SafetyNET
SHIPBOARD EQUIPMENT
NAVTEX receiver
SafetyNET receiver
Maritime-06
By agreement between IMO, the International Hydrographic Organization (IHO) and the World Meteorological Organization (WMO), the world is divided into 21 NAVAREAs/METAREAs (including five areas recently introduced for the Arctic region) as shown in Fig. 7.
10
Maritime Manual
FIGURE 7 NAVAREAs/METAREAs for promulgating maritime safety information by radio showing the area coordinators for navigational warnings and meteorological information
XVIII
Canada
XIX
Norway
XX
Russian Federation
XXI
Russian Federation
XVII
Canada
I
United Kingdom
XIII
Russian Federation
IV
United States
III II
France Spain (NAV) Greece (MET)
XII
United States
IV
United States
IX
Paskistan
XI
Japan (NAV) Japan China (MET)
VIII
India (NAV)
XVI
Peru (NAV) United States (MET)
V
Brazil
VI
Argentina
VII
South Africa
X
Australia
XIV
New Zealand
XV
Chile
VI
Argentina
Maritime-07
NOTE 1 The delimitation of such areas is not related to and shall not prejudice the delimitation of any boundaries between States.
Information is provided for defined areas of sea. Navigational warnings are provided in accordance with the standards, organization and procedures of the IHO/IMO WorldWide Navigational Warning Service. Meteorological information is provided in accordance with the WMO technical regulations and recommendations. SAR information is provided by the various authorities responsible for coordinating maritime search and rescue operations and other urgent safety-related information is provided by the relevant national or international authority responsible for managing the system or scheme.
Maritime Manual
11
2.4
1
The main sub-systems used in the GMDSS may be described as follows: The digital selective-calling (DSC) is incorporated in MF, HF and VHF radios to provide a quick and reliable means of communication between ships and the shore and between ships. DSC is a signalling system which provides a method of calling a station or a group of stations. DSC provides automated access to coast stations and ships for the transmission and reception of all types of messages from the routine to the distress category. This automated calling system is used as the initial means of contact with other stations. The DSC system is optimized for use in emergencies and the distress alert includes information on the identity of the vessel in distress and the last recorded position and can also include the nature of the distress. 2 The satellite communication system Satellite networks are capable of providing a full range of communication services, encompassing all general communications requirements, as well as distress and safety functions, within the network coverage area. 3 The Maritime Safety Information (MSI) system Two principal methods are used for broadcasting maritime safety information; NAVTEX for broadcasts to coastal waters, within approximately 200 nautical miles from the shore, and SafetyNET for broadcasts which cover all the waters of the globe except for sea area A4. HF NBDP may also be used to promulgate maritime safety information in areas outside SafetyNET or NAVTEX coverage particularly for sea area A4. Many coastal authorities also broadcast maritime safety information by radiotelephony for use by vessels which are not carrying NAVTEX or SafetyNET receivers. These vessels do not benefit from the automatic monitoring and recording provided by these receivers and require a radio watch to be kept at the appropriate time. 4 The emergency position-indicating radiobeacon system The emergency position-indicating radiobeacon (EPIRB) alerting facilities are available through the Cospas-Sarsat satellite system which is designed to provide distress alert and location data to assist SAR operations, using spacecraft and ground facilities to detect and locate signals of distress beacons operating on 406 MHz. EPIRBs may be installed to float free of a sinking vessel and start transmitting automatically. The 406 MHz system also supports radiobeacons carried aboard aircraft (ELTs) or used as personal locator beacons (PLBs).
12
Maritime Manual
Search and rescue locating devices are used to locate a survival craft or a distressed vessel. They can be either radar SART (Search and Rescue Transponder) or AIS-SART (Automatic Identification System Search and Rescue Transmitter). The intent is that the locating device is compatible with the equipment normally carried on a ship so that any ship can conduct a rescue operation if special search and rescue vehicles are not available. The SART is a portable radar transponder (racon) which is designed to provide a locating signal when interrogated by 9 GHz (3 cm wavelength) radar. The AIS-SART operates by sending updated position reports which can be read by the AIS receiver on the rescuing ship. 6 The on-scene system The on-scene system enables short to medium range communications to be carried out during the course of a search and rescue operation. This is typically achieved by the use of VHF portable radios (called two-way VHF radiotelephone apparatus) working on the maritime channels or possibly aeronautical channels. Further information on the radio systems used in the GMDSS is given in Chapter 5 of this Manual.
3
3.1
The International Telecommunication Union (ITU) was founded in Paris in 1865 as the International Telegraph Union. ITU took its present name in 1934 and became a specialized agency of the United Nations in 1947 (see Fig. 8). The ITU Radiocommunication Sector (ITU-R) plays a vital role in the global management of the radio-frequency spectrum and satellite orbits limited natural resources which are increasingly in demand from a large and growing number of communication services. The basic texts of the ITU are its Constitution and its Convention. For radiocommunications the Constitution and the Convention are complemented by the Radio Regulations which are binding on the ITUs 191 Member States. The ITU-R carries out studies and approves Recommendations on radiocommunication matters intended to assure the necessary performance and quality in operating radiocommunication systems. The ITU Constitution describes the basic requirements of telecommunications and in particular includes Articles for secrecy of telecommunications, priority of telecommunications concerning safety of life, harmful interference, distress calls and
Maritime Manual
13
messages, and false or deceptive distress or identification signals. These Articles are described further in Chapter 10.
FIGURE 8 The ITU headquarters in Geneva, Switzerland
Maritime-08
The ITU Convention describes operational matters including arrangements for the charges for telecommunication services. By agreement, transmissions concerning distress traffic, urgent ship-to-shore navigational and meteorological danger reports and medical assistance for persons in grave and imminent danger are free of charge to ships. The Radio Regulations include many provisions of direct relevance to the stations on ships and shore, to the operation of communication services, to the conduct of distress and safety communications and to the GMDSS in general. The most relevant provisions of the Radio Regulations can be found in: Chapter V dealing with licensing and identification of radio stations; Chapter VII related to distress and safety communications; Chapter IX fully devoted to maritime services;
14
Maritime Manual
Appendices 15, 17 and 18 containing information on GMDSS frequencies, HF and VHF communications.
These will be explored further in later chapters. Volume 2 of this ITU Maritime Manual includes the full texts of the Articles and Appendices of the Radio Regulations related to maritime issues. Such detailed international regulations of maritime communications are required due to a broad international use of equipment and practices, which implies the need to have the relevant procedures and technical material at the international level. Fundamental to the system of regulation is the requirement for licensing which is the subject of Radio Regulations, Article 18. Article 18 states that no transmitting station may be established or operated without a licence issued by or on behalf of the government of the country to which the station in question is subject. The government which issues the licence indicates therein the particulars of the station, including its name, call sign and the general characteristics of the installation in one of the languages of the ITU. The licence also mentions that the holder is required to preserve the secrecy of telecommunications (see Chapter 10). The ITU further maintains and updates the Global Administration Data System (GLAD) www.itu.int/ITU-R/go/glad published on the ITU web site. GLAD is an online data retrieval-system and a central repository of ITU-R common information concerning administrations and geographical areas. It includes: List of all geographical area designations. List of ITU Member States. List of non-Member States of the ITU but Member of the UN. List of symbols designating certain International Organisations. List of special regional designations. List of symbols indicating a special administrative status. Table of International Call Sign Series. Table of Maritime Identification Digits (MIDs). Table of coast station identification numbers. Table of ship station selective call numbers. Table of selective call numbers for predetermined groups of ship stations.
The site also contains the following allocation tables (see Chapter 9):
ITU also maintains and updates the Maritime mobile Access and Retrieval System (MARS) www.itu.int/ITU-R/go/mars. This internet-based system provides users with the means to access and retrieve operational information registered in the ITU maritime database. This information has been notified, to the Radiocommunication Bureau, by
Maritime Manual
15
Administrations of the Member States of the ITU. The ITU maritime database contains information concerning: Ship stations. Coast stations. Addresses of Accounting Authorities. Addresses of administrations which notify information. MMSI assigned to Search and Rescue (SAR) aircraft. MMSI assigned to AIS Aids to Navigation (A to N).
MARS also links to other maritime-related sites within the Radiocommunication Bureau and makes available the various notification forms used for the submission of data. MARS is available to everyone and at no cost on a 24 h/7 day basis and updates are carried out weekly (at 03:00 UTC every Monday morning). Further information is also provided in ITU publications including the List of Coast Stations and Special Service Stations (List IV), the List of Ship Stations and Maritime Mobile Service Identity Assignments (List V). An overview of ITU publications of most relevance to maritime communications is given in Chapter 11.
3.2
The International Maritime Organization (IMO) Convention was adopted at a conference held in Geneva in 1948 under the auspices of the United Nations and it entered into force in 1958. The first meeting of IMO was held in London in 1959. IMO (see Fig. 9) is the specialized agency of the United Nations with responsibility for the safety and security of shipping and the prevention of marine pollution by ships. The 168 member governments use IMO to draw up internationally agreed standards, for which there are now 29 Conventions together with some 600 codes and recommendations that can be applied to ships. The International Convention for the Safety of Life at Sea (SOLAS) in its successive forms is generally regarded as the most important of all international treaties concerning the safety of merchant ships. The first version was adopted in 1914, in response to the Titanic disaster, the second in 1929 and the third in 1948. The SOLAS Convention then became one of the main instruments of the IMO and the first major task for the new Organization. The resulting 1960 Convention represented a considerable step forward at the time in modernizing regulations and in keeping pace with technical developments in the shipping industry. The intention was to keep the Convention up to date by periodic amendments but in practice the amendments procedure proved to be very slow. It became clear that it would be impossible to ensure the entry into force of amendments within a reasonable period of time.
16
Maritime Manual
Maritime-09
As a result, a completely new Convention was adopted in 1974 which included a new amendment procedure the tacit acceptance procedure designed to ensure that changes are made within a specified (and acceptably short) period of time. The SOLAS, 1974 Convention was subsequently amended in 1988 to introduce the provisions for the GMDSS. The chapters of the SOLAS Convention of most relevance to the GMDSS are: Chapter II-1 (Construction Structure, subdivision and stability, machinery and electrical installations) which includes the requirements for an emergency source of electrical power capable of powering the radio installations for a period of 36 hours for passenger ships and 18 hours for cargo ships. Chapter III (Life-saving appliances and arrangements) which includes the requirements for the carriage of VHF portable radios and search and rescue locating devices.
Maritime Manual
17
Chapter IV (Radiocommunications) which describes the GMDSS, the undertakings by contracting governments to provide radiocommunication services and the ship requirements. Chapter V (Safety of Navigation) which contains the obligation for governments to disseminate navigational and meteorological warnings and provide search and rescue services, the requirements to carry certain navigational equipment some of which is associated with the GMDSS such as the carriage of a receiver for a global navigation satellite system and the carriage of a radar compatible with the SART, the requirement to carry the International Code of Signals and Volume III of the International Aeronautical and Maritime Search and Rescue (IAMSAR) Manual, and the obligation for the master of a ship to communicate danger messages and provide assistance in distress situations.
SOLAS Chapter IV applies (with some exceptions) to all passenger ships and to cargo ships of 300 gross tonnage and upwards when engaged in international voyages. A passenger ship is defined as a ship which carries more than twelve passengers, where a passenger is defined as any person other than the master and the members of the crew or other persons employed or engaged in any capacity on board the ship on the business of the ship and a child under one year of age. A cargo ship is simply defined as any ship which is not a passenger ship. Gross tonnage is a function of the internal volume of a ship calculated by methods given in the International Convention on Tonnage Measurement of Ships. It provides a measure of the cargo carrying capacity of a ship and forms the basis for manning regulations, safety rules, registration fees and port dues. An international voyage means a voyage from a country which has adopted the SOLAS Convention to a port outside the country, or conversely. The Conventions, codes and recommendations of the IMO which are of most relevance to maritime communications are given in Chapter 11.
3.3
The term Administration is used to describe any governmental department responsible for discharging the obligations of the binding conventions of the United Nations. In any one country there will typically be different departments for ITU matters and IMO matters. The individual administrations transpose the convention requirements into the national legislation of the country. Administrations frequently set up national authorities to support the legislation for the country dealing with specialized activities. For radio matters these might be activities such as radio licensing (see 3.1), examination for operators certificates (see Chapter 8 and Fig. 10), assigning MMSIs (see Chapter 9), national frequency planning and control of interference (see Chapter 10). For maritime matters they might
18
Maritime Manual
be registration of ships, certification of ships and seafarers, inspection of ships and provision of aids to navigation. An administration that maintains a register of ships is termed a Flag state which means a state whose flag a ship flies and is entitled to fly.
FIGURE 10 Training centre set up by the Norwegian Administration for operators certificates
Maritime-10
4
4.1
The provisions for distress and safety communications are given in the Radio Regulations, Chapter VII. Distress and safety communications include distress, urgency and safety calls and messages. The Chapter contains the provisions for the operational use of the GMDSS which are obligatory in the maritime mobile service and maritime mobile-satellite service for all stations using the frequencies and techniques of the GMDSS.
Maritime Manual
19
The Chapter refers to the SOLAS Convention for the detail of the functional requirements, system elements and equipment carriage requirements of the GMDSS. Within Chapter VII, Article 30 of the Radio Regulations contains the general provisions which include aeronautical provisions and certain provisions for land mobile stations. Mobile stations of the maritime mobile service are permitted to communicate, for safety purposes, with aircraft (see Fig. 11) using the GMDSS procedures and frequencies.
FIGURE 11 Aircraft are permitted to use the GMDSS for safety purposes. Search and Rescue aircraft may be fitted with both aeronautical and maritime VHF communications including DSC, with Automatic Identification Systems and with direction finding equipment to home on 121.5 MHz and 406 MHz
Maritime-11
Additionally, aircraft may communicate, for distress and safety purposes, with stations of the maritime mobile service. Aircraft, when conducting search and rescue operations, are also permitted to operate digital selective-calling (DSC) equipment on the VHF DSC frequency 156.525 MHz (channel 70), and automatic identification system (AIS) equipment on the AIS frequencies 161.975 MHz and 162.025 MHz.
20
Maritime Manual
Land mobile stations in uninhabited, sparsely populated or remote areas are also permitted, for distress and safety purposes, to use the frequencies provided for the GMDSS providing the GMDSS procedures are used. Article 30 of the Radio Regulations also contains an important provision which derives from the general rules on the assignment and use of frequencies: no provision of the Radio Regulations prevents the use by a mobile station or a mobile earth station in distress of any means at its disposal to attract attention, make known its position, and obtain help.
However, it should be noted that the successful outcome of a distress incident is more likely if the procedures of the GMDSS are used to obtain assistance from the international SAR organizations. Further guidance on other means to attract attention is given in the IAMSAR Manual (published by IMO).
4.2
Functional requirements
Nine functional requirements of the GMDSS are described in SOLAS Chapter IV, regulation 4. Ships subject to the SOLAS Convention are required to be capable of performing all nine functions while at sea. Other ships should consider the nine functions when deciding to what extent they intend to participate in the international SAR system (see 4.6). The functional requirements are: 1 Transmitting ship-to-shore distress alerts by at least two separate and independent means, each using a different radiocommunication service
On a sea area A1 ship, for example, the primary means would be the VHF DSC, and the secondary means could be a satellite EPIRB. In the case of a sea area A4 ship, the primary means would have to be HF DSC and the secondary means a satellite EPIRB. If the EPIRB is used as the secondary means of alerting it has to be capable of being activated from a position close to the position from which the ship is normally navigated. This may mean carrying an extra EPIRB on some ships as the float-free EPIRB needs to be mounted clear of obstructions. 2 Receiving shore-to-ship distress alerts If, for example, a ship sends a distress alert via an EPIRB or Inmarsat C satellite terminal, any ships which might be in the vicinity will not become aware of the distress until the shore authorities relay the distress details by directing a DSC call and/or a satellite call to all ships within a defined area. 3 Transmitting and receiving ship-to-ship distress alerts A ship in distress can alert other ships in the vicinity by sending a DSC distress alert on VHF and follow it up with a distress (MAYDAY) voice call and message on VHF channel 16.
Maritime Manual
21
The functions for rescue co-ordination are described in the IAMSAR Manual. Normally, a rescue co-ordination centre will designate a Search and Rescue Mission Co-ordinator for the duration of the incident who will select communication methods appropriate to the incident and the vessels involved. 5 Transmitting and receiving on-scene communications On-scene communications are coordinated by the designated On-Scene Commander as described in the IAMSAR Manual and may involve communications with aircraft, as well as with other ships and the shore. 6 Transmitting and receiving signals for locating The SART receives signals from a ships 9 GHz radar and responds with a characteristic transmission. The AIS-SART does not have a receiver and transmits autonomously on VHF channels. Satellite EPIRBs also contain a homing beacon working on the aeronautical frequency of 121.5 MHz and some aircraft are also capable of homing on the 406 MHz transmissions of the EPIRB. 7 Transmitting and receiving maritime safety information VHF radiotelephony may be used to transmit danger messages to ships in the vicinity, reporting dangerous ice, dangers to navigation, tropical storms, sub-freezing air temperatures or winds of force 10. MF, HF or satellite systems may be used to transmit these messages to competent authorities ashore and also to transmit meteorological information. Maritime safety information can be received by NAVTEX and SafetyNET. 8 Transmitting and receiving general radiocommunications to and from shorebased radio systems or networks
General radiocommunications include safety traffic concerned with ship reporting communications, communications relating to the navigation, movements and needs of ships and weather observation messages. Whilst a ship subject to the SOLAS Convention must comply with the nine functional requirements of the GMDSS, this requirement alone is not considered as making a ship unseaworthy or as a reason for delaying a ship in ports where repair facilities are not readily available providing the ship is capable of performing all distress and safety functions. 9 Transmitting and receiving bridge-to-bridge communication VHF channel 16 watch should be kept while at sea for bridge-to-bridge communications. The frequency 156.650 MHz (channel 13) is also used for ship-to-ship communications relating to the safety of navigation and the safe movement of ships. For ships subject to the SOLAS Convention there is a requirement that access to VHF communication equipment must be available from the position at which the ship is normally navigated.
22
Maritime Manual
4.3
In order to meet the above functional requirements, SOLAS Chapter IV, regulations 7 to 11, detail the equipment that ships are required to carry: a VHF radio installation capable of transmitting and receiving DSC and radiotelephony; a search and rescue locating device (which may be one of those required by the life saving appliance regulations of SOLAS Chapter III); a NAVTEX receiver if the ship is engaged on voyages in which an international NAVTEX service is provided; an Inmarsat enhanced group call system (Inmarsat C) if the ship is engaged on voyages where a NAVTEX service is not provided; a satellite EPIRB capable of floating free if the ship sinks.
In addition, passenger ships are required to carry a means of two-way on-scene communication using the aeronautical frequencies 121.5 MHz and 123.1 MHz. Ships are then required to carry further equipment depending upon the sea area in which the ship is sailing to achieve the requirements for a primary and a secondary means of distress alerting to the shore and any duplication (see below) of equipment required. SOLAS Chapter III, in regulations 6 and 26 details requirements for the carriage of hand-held radios (see Fig. 12) and search and rescue location devices. Typical equipment fits (see Fig. 13), which include the life-saving appliances requirements from SOLAS Chapter III, are summarised in Table 1.
4.4
Maintenance requirements
For ships conforming to the SOLAS Convention, the means of ensuring the availability of equipment, are determined by the sea areas in which the ship sails and is given in SOLAS Chapter IV, regulation 15. In sea areas A1 and A2, the availability of equipment is ensured by one of the following strategies: a) b) c) duplication of equipment; shore-based maintenance; at sea electronic maintenance;
or a combination of the above, as may be approved by the flag administration. In sea areas A3 and A4, the availability of equipment is ensured by using a combination of at least two of the above, as may be approved by the flag administration. The majority of ships adopt duplication with shore-based maintenance.
Maritime Manual
23
FIGURE 12 The SOLAS hand-held radios (also called survival craft two-way VHF radiotelephones) are intended for use in life-rafts by persons who may be wearing gloves. They are required to be yellow or orange in colour and be supplied with a dedicated primary battery for use in distress situations. These batteries can be seen stored in the charger units alongside the radios
Maritime-12
FIGURE 13 Part of the radio installation on the bridge of a large ship showing MF/HF radio and radiotelex, VHF radio, hand-held VHF radios and NAVTEX. The ship also carries Inmarsat C
Maritime-13
24
Maritime Manual
TABLE 1 Examples of typical equipment carriage for ships conforming to the SOLAS Convention
Sea Area A1 X Sea Area A2 X X Sea Area A3 Satellite Solution X X X X X X X X X X(2) X(3) X X X X(2) X(3) X X X X(2) X(3) X X X X(2) X(3) X X X X(2) X(3) X X X X Sea Area A3 HF Solution X Sea Area A4 X
Equipment
VHF telephony with DSC MF telephony with MF DSC Inmarsat ship earth station with EGC (Enhanced Group Call) receiver MF/HF telephony with DSC and telex Duplicated VHF with DSC Duplicated Inmarsat ship earth station(1) Duplicated MF/HF telephony with DSC and telex(1) NAVTEX receiver Float-free satellite EPIRB Search and rescue locating device: SART/AIS-SART Hand-held waterproof VHF radio For passenger ships: Distress panel For passenger ships: Two-wayon-scene radiocommunication on 121.5 MHz or 123.1 MHz from the navigation bridge
(1) (2)
Some authorities accept 1 ship earth station and 1 MF/HF as equivalent to duplication. Cargo ships between 300 and 500 gross tonnage: 1 set. Cargo ships of 500 gross tonnage and upwards and passenger ships: 2 sets. Ro-Ro passenger ships: 1 set to every four life-rafts. Cargo ships between 300 and 500 gross tonnage: 2 sets. Cargo ships of 500 gross tonnage and upwards and passenger ships: 3 sets.
(3)
Maritime Manual
25
4.5
The GMDSS requirements have been incorporated by IMO into the requirements for some types of ships which are not subject to the SOLAS Convention but are the subject of certain codes. These are: Code of Safety for Dynamically Supported Craft (DSC Code) (see Note 1). Code of Safety for Special Purpose Ships (SPS Code). Code for the Construction and Equipment of Mobile Offshore Drilling Units (MODU Code). International Code of Safety for High-Speed Craft.
NOTE 1 These Codes are published by IMO. Fishing vessels are also encouraged to be fitted with the equipment for the GMDSS and in many parts of the world there are national or regional requirements for fishing vessels to carry certain equipment. The Torremolinos International Convention for the Safety of Fishing Vessels includes Chapter IX on radiocommunications which is very similar to SOLAS Chapter IV. This Convention applies to vessels of 45 m or over in length. For fishing vessels of 24 m or over (see Fig. 14), GMDSS carriage requirements, which are simplified over those of SOLAS Chapter IV, are included in the FAO/ILO/IMO Code of Safety for Fishermen and Fishing Vessels (see Note 2).
FIGURE 14 The world fishing fleet numbers about 4 million vessels. About two-thirds are undecked and not fitted with mechanical propulsion systems. Those longer than 24 m such as these vessels total about 1%
Maritime-14
26
Maritime Manual
For fishing vessels of 12 m and over, GMDSS guidance is given in the FAO/ILO/IMO Voluntary Guidelines for the Design, Construction and Equipment of Small Fishing Vessels. NOTE 2 Published by IMO on behalf of the Food and Agricultural Organization (FAO) and the International Labour Organization (ILO).
4.6
Ships which are not required to comply with the SOLAS Convention are recommended by IMO to comply with at least the following functional requirements to allow effective participation in the GMDSS with respect to distress and safety communications in order to provide safety for own ship: 1 2 3 4 1 2 transmitting ship-to-shore distress alerting; transmitting ship-to-ship distress alerting; transmitting and receiving on-scene communications including appropriate SAR co-ordinating communications; transmitting locating signals, receiving shore-to-ship distress alerting; receiving ship-to-ship distress alerting.
To achieve these functional requirements ships are recommended to carry VHF equipment with DSC (see Fig. 15) and maintain a channel 16 and DSC watch. When operating beyond coastal areas they are recommended to carry a satellite EPIRB (see Fig. 16) and other radio equipment appropriate to their area of operation. They are also recommended to make provision for reception of maritime safety information.
Maritime Manual
27
FIGURE 15
An example of a VHF radio with built-in DSC to a simplified standard known as Class D from Recommendation ITU-R M.493. This radio permits the functional requirements to be met with simpler training for the operator (see Chapter 8)
Maritime-15
FIGURE 16 Carriage of an EPIRB is recommended for voyages beyond coastal areas. This example is being carried on a sailboat in a float-free housing
Maritime-16
28
Maritime Manual
Advice on the carriage of suitable equipment is given in Table 2. TABLE 2 Recommended equipment carriage for ships not conforming to the SOLAS Convention
Area of operation from coast (nautical miles) VHF telephony with DSC Hand-held waterproof VHF radio also for use in life-raft Satellite EPIRB(1) MF telephony with DSC
(2)
Up to 20 R R O None None O O
Up to 60 R R R O O R O
Up to 150 R R R R R R R
Unrestricted R R R R R R R
Satellite ship earth station Inmarsat or other provider NAVTEX receiver Search and rescue locating device; SART/AIS-SART
(1) (2)
Float-free or readily accessible Not required if satellite ship earth station is fitted O Optional
R Recommended
In some parts of the world there are national or regional requirements for the carriage of equipment by ships which are not large enough to be subject to the SOLAS Convention carriage requirements.
5
5.1
Radio procedures
Radiotelephony
With the frequencies used for maritime VHF (see Chapter 7) radio, radio waves travel very largely in straight lines. The communication range is determined by the heights of the antennas and any obstructions to the signal path and particularly the curvature of the Earth (see Fig. 17). A large ship to a coast station may achieve a range of 60 nautical miles but 30 nautical miles would be more typical. Between ships, 10 20 nautical miles would be typical, reducing to around 5 nautical miles for small craft using hand-held radios.
Maritime Manual
29
FIGURE 17 Diagram of VHF propagation
The large ship is within communication range of the coast station but the smaller vessel needs to be closer to the horizon
Maritime-17
The power of a VHF radio of 25 W for a fixed unit and 1 W for a hand-held unit is sufficient and does not limit the communication range. VHF is typically used for intership communications and communications in sea area A1. At HF the propagation is quite different as the radio waves, whilst still travelling in straight lines, reflect from electrically-charged layers in the upper atmosphere called the ionosphere. With this propagation method, called sky-wave, ranges of thousands of miles can be achieved (see Fig. 18). HF radio is mainly used in A3 and A4 sea areas. The higher the frequency the greater the range that can be obtained, but the properties of the ionosphere change with sunlight so frequencies over about 12 MHz provide less reliable communications during the night. With HF communications it is necessary to note the time of day, season and the required communication distance in order to determine the frequency to use. The suitable frequency can be chosen by listening for other traffic working in the band. The power required for HF communication (see Fig. 19) is greater than VHF and typically around 400 W. The maximum power of ship stations allowed by the Radio Regulations is 1 500 W. At MF the propagation mechanism is by ground wave or by sky-wave, which is present only at night and formed by successive reflection between the Earth and the ionosphere. The range is mainly dependant on transmitter output power and is of the order of a nautical mile for every 2 W of transmitter power. So a 250 W transmitter at 2 182 kHz will give a range of around 125 nautical miles. At night the range increases to around 1 000 nautical miles due to sky-wave propagation. MF radio can be used in sea areas A2, A3 and A4.
30
Maritime Manual
F2
26 MHz
F1 E 8 MHz
16 MHz
Dead zone
HF propagation during the day. At night the D layer disappears and the F layers combine. Frequencies higher than 12 MHz are not then normally reflected back to the Earth.
Maritime-18
Some radio circuits are duplex which use two frequencies and allow both parties to talk at the same time like a telephone circuit. However, commonly, radio circuits are simplex using one frequency and for these a routine needs to be established to enable successful communication. The exchange is divided into overs with just one party transmitting at any one time by using the press to talk switch. A typical call to start a communication would be: name or call sign of called station; the words THIS IS; name or call sign of the calling station; the word OVER.
Maritime Manual
31
FIGURE 19
Example of a shipborne MF/HF radiotelephone equipped with DSC. This radio has a power of 150 W for simple installation on smaller ships
Maritime-19
The response from the called station will agree on a channel to use for subsequent communications. The exchanges finish by using the word OUT. To facilitate communications, procedure words (prowords) are commonly used to convey information in a standard form. Examples are; CORRECT that is correct, NOT CORRECT that is not correct, RECEIVED your message has been received, I SAY AGAIN I am repeating the transmission. For clarity the phonetic alphabet and figure code may be used (see Chapter 10) following the proword I SPELL.
5.2
Digital selective-calling (DSC) is a technique of transmitting remote control commands, in the form of digital codes, which allows suitably equipped stations to: a) b) c) d) e) f) transmit and receive distress alerts; transmit and receive distress alert acknowledgments; relay distress alerts; transmit and receive urgency and safety calls; transmit and receive routine priority calls and set up working channels for subsequent general communications by radiotelephony; set up and receive telephone calls to shore telephone networks (although few telephone networks now offer this service).
32
Maritime Manual
DSC thus provides automated access to coast stations and ships for distress and safety purposes, and can be used for routine calling as well, in place of the voice procedures described above. DSC equipment operates by sending digital codes which the receiving equipment then interprets as messages and further instructions. The associated message information is shown on a display panel or sent to a remote printer. Since the message information is stored in the receiver it can also be displayed or printed out some time later following receipt. DSC codes can also command the transceiver at the receiving station to set itself up on working frequencies nominated by the sender. Four levels of priority distress, urgency, safety and routine are available for DSC calls. At the coast station, ship-to-shore distress calls receive priority handling and are routed to the nearest RCC. On board ship, DSC receivers sound an alarm when a distress call is received. DSC equipment is available for communications in the MF, HF and VHF bands and consists of a DSC controller or encoder that provides for various operations through an automated receiver and an associated transmitter. Reception of DSC calls and the transmission of DSC distress calls are standard automated functions. DSC calls may be made to all stations, individual stations, stations in a geographic area or groups of stations. The identity (MMSI see Chapter 9) of the calling station is automatically included in every call. Distress calls are automatically addressed to all stations and automatically include the ship position provided that the DSC equipment is connected to a suitable electronic position fixing system such as GPS or other satellite navigation receiver. Stations on ships conforming to the SOLAS Convention are required to have this connection although facilities are additionally available to enter the position manually. The position coordinates are transmitted with a resolution of one minute which is about a nautical mile. Newer DSC equipment incorporate an additional expansion message which gives a resolution of ten thousandths of a minute providing position accuracies of a few metres. With newer DSC equipment (see Fig. 20) the distress call is made by means of a dedicated button which is held down for three seconds. If time permits, there is a facility to add a nature of distress message to assist SAR authorities for which the options are: fire/explosion, flooding, collision, grounding, listing/in danger of capsizing, sinking, disabled and adrift, abandoning ship, piracy/armed robbery attack, and man overboard. The distress call otherwise is transmitted as undesignated. At VHF the distress call is transmitted on VHF channel 70 and at MF/HF is transmitted on six frequencies (1 at MF and 5 at HF) although facilities are provided to select an individual frequency. Distress calls are automatically repeated after a delay of 4 minutes until they are acknowledged or stopped by the ship operator. Routine calls frequency to frequencies is available for are made by entering the MMSI of the station to be called and the be used for subsequent communications. The choice of suitable described in Chapter 7, for example at VHF, pre-assigned channels are ship-to-ship communications and ship-to-shore communications. In
Maritime Manual
33
the MF and HF bands, DSC calls can be received at greater range than is possible for radiotelephony so there can be some difficulty in carrying out subsequent radiotelephone communications in the same frequency band at extreme range or if there is interference. A successful DSC call does not therefore indicate that subsequent radiotelephone transmissions in the same MF or HF band will be of intelligible quality.
FIGURE 20 DSC controllers are normally built into radio equipment. This example of a VHF radio with DSC meets the standards for use on ships which comply with the SOLAS Convention. The distress button is at the lower left
Maritime-20
DSC may be tested by calling another station and if an acknowledgement follows from that station, the test is successful. For MF/HF a special test call is available which can not be confused with a distress or safety call and some coast stations are equipped to automatically respond to the test call. Testing on the MF/HF frequencies should be limited to once a week to prevent overloading of the channels. A test call is also available at VHF for use with suitably equipped coast stations.
34
Maritime Manual
DSC uses radio signals based on high and low audio tones. A series of seven tones represents one character giving a total of 27 or 128 combinations, known as symbols 00 127, each of which translates into an instruction to the receiving equipment. The MF/HF system uses a 500 Hz channel operating at 100 Baud and the VHF system a 25 kHz channel operating at 1 200 Baud. A call lasts for about 7 seconds on MF/HF, and about 0.6 seconds on VHF. Because of the communication capacity limitations of the narrow-band MF/HF channels, separate DSC channels have been allocated for initiating distress and safety calls and for controlling routine category calls in the 2, 4, 6, 8, 12 and 16 MHz MF/HF bands. On VHF, the wider channel bandwidth means that the channel loading capacity is sufficient for all categories of DSC initiated communications to be accommodated on the single VHF DSC channel 70. All DSC calls automatically include error checking signals. The DSC signal structure includes an initial dot pattern of 20 bits to help the receiver synchronize with the transmission. At MF/HF the dot pattern is increased to 200 bits for distress calls and certain other calls which permits the use of scanning receivers. Scanning receivers cannot be used at VHF.
5.3
Inmarsat
The Inmarsat system comprises four satellites in geostationary orbit which between them provide coverage of four ocean regions (see Fig. 21) between about 76N and 76S. The Inmarsat system does not provide coverage in sea area A4. Inmarsat offers three satellite communication systems designed to provide GMDSS functions required by ships conforming to the SOLAS Convention: Inmarsat B, Inmarsat C and Inmarsat Fleet 77. Many ships carry an Inmarsat C terminal in order to comply with the carriage requirements of the SOLAS Convention. All systems are equipped with a distress-alerting feature which, in the event of an emergency, automatically sends a top priority alert to an RCC ashore. Inmarsat also offers other satellite communication systems: Mini M, Fleet 55 and Fleet 33 which are suitable for ships which do not need to conform to the SOLAS Convention as described in 4.6. These systems may rely on spot beams which do not have complete global coverage. Inmarsat B launched in 1993 (see Note 1) supports global voice, telex, fax and data at speeds from 9.6 kbit/s to 64 kbit/s. Inmarsat C offers two-way, store-and-forward packet data communications at 600 bit/s via a small, low-cost terminal. It handles operational and personal messages, including email, telex and fax, in addition to distress and safety communications. Inmarsat Fleet 77 provides full support for GMDSS, including advanced features such as call prioritisation and pre-emption and provides voice and high-speed data up to 128 kbit/s. NOTE 1 Inmarsat has given notice that the Inmarsat B service will terminate on 31 December 2014.
90
80
Maritime Manual
70
60
50
40
30
20
10
54E AOR-W 15.5W AOR-E 64E IOR 178E POR
178E POR
10
20
30
40
50
60
70
80
90 180 100 80 60 40 20
160
140
120
20
40
60
80
100
120
140
160
180
Pacific Ocean Region Atlantic Ocean Region-West Atlantic Ocean Region-East Indian Ocean Region
Fleet 77 voice, fax, MPDS, 64 kbit/s ISDN Fleet 55, 33, voice lsat M2M Inmarsat B (all services) Inmarsat C (all services)
35
maritime-21
36
Maritime Manual
Virtually all of the telecommunication services found in offices ashore are available to ships equipped with Inmarsat ship earth stations (SES). This results in ships having capabilities for high quality, reliable and automatic communications via telephone, facsimile, data and e-mail. Additionally Inmarsat offers a Fleet Broadband service FB500, FB250 and FB150 which provides internet connection (see Fig. 22).
FIGURE 22 Example of Fleet Broadband terminals showing the above decks antenna unit and the below decks equipment. The larger antenna supports the FB500 service which permits communication at 432 kbit/s and the smaller supports FB250 for communication at 284 kbit/s.
Maritime-22
A series of 2-digit service codes has been established to make it faster for ships to make connections for a number of special purposes. Of these, there are six which are specifically for safety services and provide a rapid connection to an RCC, meteorological office, hydrographic office, ship reporting centre or medical centre. For instance Code 32 is used for medical advice, Code 38 for medical assistance and Code 39 for maritime assistance.
Maritime Manual
37
The Inmarsat C SES (see Fig. 23) has a small omnidirectional antenna which, because of its light weight and simplicity, can be easily mounted on a ship and will continue to provide a service even when the vessel is listing. The main electronics unit is compact, weighing 3-4 kg, and comes with a standard port for connection to PCs or other data equipment. Inmarsat C can handle messages up to 32 kbit/s in length. Each message is transmitted in data packets via satellite to a land earth station (LES), where it is reassembled and then sent to the ultimate addressee via the national and international telecommunications networks. In the reverse direction, callers may send messages to a single SES or to a group of SESs. Inmarsat C SESs are also capable of data reporting and polling, and position reporting.
FIGURE 23 Example of Inmarsat C showing the electronics unit and the antenna
Maritime-23
Inmarsat C terminals are equipped with a distress-alerting feature which automatically generates and sends a priority distress alert, incorporating position and other information, to an RCC. The procedure for sending a distress alert is similar to that for DSC. The dedicated distress button is pressed and held. If there is time to enter information, a Distress menu allows entry of the Nature of Distress. The LES should acknowledge the alert but if an acknowledgement is not received within 5 minutes the distress alert is repeated. After the distress alert is sent and an acknowledgement received, a more detailed distress priority message may be sent advising more detailed information about the distress incident and/or assistance required. This distress priority message should be sent through the same LES as the distress alert and will also be automatically routed to the same RCC. With Inmarsat B and Inmarsat Fleet 77, distress calls are made by telephone. The procedure for sending a distress alert is to select the telephone mode of operation, Distress Priority and the required LES access code. When Call Request is initiated the call will be directed directly to the RCC associated with the LES. If a response is not
38
Maritime Manual
received within 15 seconds, the distress call is repeated. When contact has been established, the normal MAYDAY procedures are followed (see Chapter 6). Inmarsat B and C provide two levels of priority but Inmarsat Fleet 77 provides four levels of pre-emption and prioritisation in both the ship-to-shore and shore-to-ship directions. Data services are regarded as Other (Routine) priority communications and are liable for pre-emption if a voice call using a higher priority is initiated. If the Fleet 77 is currently being used in data mode and a telephone call using a higher priority than Routine, is either initiated by an operator on board the ship or signalled as an incoming call in the shore-to-ship direction, the Fleet 77 equipment will pre-empt to current communication, i.e. shut it down, and connect the voice call which has a higher priority. Hierarchical pre-emption also occurs between voice calls: distress priority calls will always pre-empt Urgency priority calls; urgency priority calls will always pre-empt Safety priority calls; safety priority calls will always pre-empt Other (Routine) priority calls.
Inmarsat C terminals (see Fig. 24) can receive broadcast messages known as Enhanced Group Calls (EGC). A special header is added to the text to indicate the group of ships or the geographical area to which the message is to be sent. There are two types of EGC: SafetyNET which provides a means of transmitting maritime safety information to vessels at sea and is used by hydrographic, search and rescue, meteorological and coastguard co-ordination authorities. Messages can be directed to ships in specific regions such as one of the IMO NAVAREAs/METAREAs or the sea area around a search and rescue incident. FleetNET which allows commercial information to be sent to a number of predesignated ships simultaneously. It is suitable for use by services specializing in the distribution of news, stock exchange reports, sporting results, weather analyses, and road/port information.
SafetyNET fulfils an integral role in the GMDSS. The Information Provider forwards the SafetyNET MSI for a given area to an Inmarsat C LES, for broadcasting via the satellite network over an entire Inmarsat ocean region. Ships can therefore receive SafetyNET MSI anywhere in that ocean region, irrespective of their distance from the LES/information provider. MSI for a given area is generally broadcast over either NAVTEX or SafetyNET (except for some circumstances where a message may be broadcast using both services); ships equipped with both a NAVTEX receiver and SafetyNET receiver should select the appropriate receiver to receive MSI for a particular area. Where a coastal area is not covered by the international NAVTEX service, for example around Australia, MSI for that area will be broadcast on SafetyNET.
Maritime Manual
39
FIGURE 24
Inmarsat C fitted on the bridge of a large ship with data terminals and printers. Two Inmarsat Cs are fitted to provide duplication to meet the maintenance requirements (see Chapter 4)
Maritime-24
In operation the SafetyNET EGC receiver is programmed for the relevant NAVAREA/METAREA (and coastal MSI area) for the voyage. Figure 25 shows how the NAVAREAs/METAREAs map onto the coverage of the satellites. The receiver is also programmed for the types of information of interest in a similar way to a NAVTEX receiver (see below). The ships electronic position fixing system ensures that the receiver accepts messages addressed to a relevant geographic area. In the shore-to-ship direction, ships are alerted through automatic receipt of distress relays initiated by RCCs transmitted through the SafetyNET service. Ordinary telex group calls to Inmarsat B SESs can also be used to supplement this. Inmarsat terminals on board ships can be utilized for originating and receiving communications with other ships involved in distress incidents and for communications with RCCs. When multiple ships are involved, the EGC system is advantageous for operational updates and planning actions from RCCs.
40
Maritime Manual
INSAT-2A SARSAT
Maritime-25
5.4
NAVTEX
The international NAVTEX service is the system for the broadcast and automatic receipt of MSI on 518 kHz using the English language. The system is fully described in the IMO NAVTEX Manual (Published by IMO). The purpose of the NAVTEX system is to provide MSI relevant to the coastal areas within the range of the NAVTEX transmitter network. The information provider forwards the MSI for a given area to a 518 kHz MF NAVTEX transmitter. The system uses the modulation of two audio tones, similar to DSC, at a rate of 100 Baud with built-in error correcting. The preamble to each message includes a technical code of four characters called B1, B2, B3, B4. The first character B1 is the transmitter identification character which is a single unique letter allocated to each transmitter. It is used to identify the broadcasts which are to be accepted by the receiver or rejected. In order to avoid erroneous reception of transmissions from two stations having the same B1 character, it is necessary to ensure that such stations have a geographical separation larger than the design range, which is normally about 400 nautical miles. This planning is achieved by the IMO NAVTEX
Maritime Manual
41
Coordinating Panel and the information is published in the List of Coast Stations and Special Service Stations (List IV) (see Note 1). NOTE 1 Radio Regulations, Resolution 339 invites IMO to provide ITU with the information. The second character is the subject indicator character used by the receiver to identify different classes of messages: A B C D E F G Navigational warnings Meteorological warnings Ice reports SAR information and pirate attack warnings Meteorological forecasts Pilot service messages AIS H I J K L LORAN messages Spare SATNAV messages Other electronic navaid messages Navigational warnings additional to letter A
The third and fourth characters B3, B4 are used to allocate a serial number within each class of message between 01 and 99 by the relevant NAVTEX coordinator. Each NAVTEX transmitting station is allocated a 10-minute transmission time every 4 hours as shown in Fig. 26. The messages printed by the NAVTEX receiver begin with ZCZC and then the B1B2B3B4 code followed by an optional time stamp. The text message begins with the message series identity and consecutive number associated with the identification of the source of the report (e.g. NAVAREA III 274). The message ends with NNNN (see Fig. 27). In operation the NAVTEX receiver is programmed with the transmitter identification characters (B1) appropriate to the area of the voyage (some receivers with an input from an electronic positioning system do this automatically). It is then programmed with the subject indicator characters (B2) of interest (A, B and D are always automatically programmed). Initially the receiver prints all the messages received but when it receives a repeated message, this is not printed. Some receivers do not have an inbuilt printer (see Fig. 28) and store the messages in an electronic memory for display on a screen. The requirement is then to store 200 messages. If a SAR message is received, an alarm is raised which will continue until cancelled.
42
Maritime Manual
Group 1
B C D E F G
Group 2
I J K L M
Group 3
N O P Q R S
Group 4
T U V W X
INSAT-2A
.10 .20 .30 .40 .50 .01 .10 .20 .30 .40 .50 .02 .10 .20 .30 .40 .50 .03 .10 .20 .30 .40 .50 .04
SARSAT
COSPAS
05
09
13
17
21
06
10
14
18
22
SARSAT
07
11
15
19
23
GOES-W GOES-E
COSPAS
08
12
16
20
24
Maritime-26
In addition to the frequency 518 kHz, the frequency 4 209.5 kHz is available for use for international NAVTEX. This is a superior frequency in tropical zones where the background noise at 518 kHz is greater. The frequency of 490 kHz is also available for national NAVTEX which is not necessarily in the English language. Modern NAVTEX receivers are required to watch at least two frequencies. To find out which MSI service, NAVTEX or SafetyNET, serves a particular area (see Fig. 29) and the broadcast schedules, a user should refer to the information for a particular area contained in the List of Coast Stations and Special Service Stations (List IV) or relevant publications produced by national administrations and service providers.
Maritime Manual
43
FIGURE 27 Standard format for NAVTEX messages
Phasing signals > 10 s Start of message group ZCZC B1B2B3B4 B 1: Transmitter identity B 2: Subject indicator B 3B 4: Consecutive number Optional
Maritime-27
Maritime-28
44
Maritime Manual
(C) (D) Riviere Au Renard (P) Thunder Bay (H) Prescott (Wiarton) (F) Boston S. Johns (O) Sydney (Q) (J) Fundy (U) (V)
(A) (D)
NAVTEX station International NAVTEX (518 kHz) National NAVTEX Limit of service area
Maritime-29
5.5
Cospas-Sarsat
The Cospas-Sarsat System includes two types of satellites (see Fig. 30), those in lowaltitude Earth orbit (LEO) which form the LEOSAR System and satellites in geostationary Earth orbit (GEO) which form the GEOSAR System. The LEO satellites operate in near polar orbits. There are normally four operational satellites deployed at any one time, at approximate heights of 850 km for SARSAT and 1000 km for COSPAS. Each Cospas-Sarsat satellite orbits the Earth on a North/South, South/North path, passing closely over both poles. The EPIRB contains a 406 MHz transmitter which sends a burst of data at about oneminute intervals which includes the ship identification. The EPIRB position can be
Maritime Manual
45
SARSAT
COSPAS
GOES-E
INSAT-2A GOES-W
COSPAS SARSAT
Maritime-30
However, some 406 MHz EPIRBs also transmit a position derived from a satellite navigation system such as GPS. This information is detected by the GEOSAR system which provides almost immediate alerting in the footprint of the GEOSAR satellite, whereas the LEOSAR system has an average waiting time of 45 minutes but provides coverage of the whole globe beyond the coverage of geostationary satellites. The transmissions are received by the satellites which pass on the relevant information to an earth station known as a Local User Terminal (LUT) which then passes information to rescue authorities via a Mission Control Centre (MCC) (see Fig. 31). The EPIRB is also equipped with a light of 0.75 candela, flashing with a low duty-cycle ratio. EPIRBs are further equipped with a buoyant lanyard suitable for use as a tether in order to secure the beacon to a life-raft, boat or person in the water. However, to prevent the EPIRB from being dragged under water, the lanyard should never be attached to the ship.
46
Maritime Manual
INSAT
GOES
Do wn lin
MSG
COSPAS
GSO satellites
Dow nlink
406 MHz
Hz 6M 40
406 MHz
SAR
PLB
406 MHz
6M 40 Hz
Hz 6M 40
Distressed Aircraft
SAR
KEY: EPIRB: emergency position indicating radio beacon ELT: emergency locator transmitter PLB: personnal locator beacon SAR: search and rescue
Maritime-31
COSPAS Space system for the search of vessels in distress (Russia) SARSAT Search and rescue satellite-aided tracking system (USA) MSG Meteosat 2nd generation satellite (EUMETSAT) GOES Geostationary operational environmental satellite INSAT Indian geostationary satellite GEOLUT Local user terminal in a GEOSAR System GEOSAR Geostationary satellite system for SAR LEOLUT Local user terminal in a LEOSAR System LEOSAR Low Earth Orbit satellite system for SAR
Maritime Manual
47
The Cospas-Sarsat system has previously also operated a service using the frequencies 121.5 MHz and 243 MHz but this service ceased on 1 February 2009. However, a 121.5 MHz signalling facility is included in the EPIRB, which serves primarily to provide a homing signal for aircraft. All EPIRBs have arrangements for local manual activation and those intended for carriage on ships conforming to the SOLAS Convention additionally have float-free release and self activation (see Fig. 32). Remote activation from the navigating bridge may also be provided, while the EPIRB is installed in the float-free mounting. The equipment, mounting and releasing arrangements are designed to be reliable, operating satisfactorily under the extreme conditions likely to be met at sea.
FIGURE 32 EPIRB supplied with a protective casing. The hydrostatic release in the top of the unit opens the casing and releases the EPIRB before the depth of water reaches 4 metres. Manual activation is achieved by removing the casing and then a protective tab on the activation switch
Maritime-32
48
Maritime Manual
Manual distress alert initiation requires at least two independent actions. EPIRBs should be installed so that they cannot be tampered with or accidentally activated (see Fig. 33). Float-free release arrangements may not be practicable on small ships where it is difficult to find a location which is clear of the waves and where the EPIRB cannot be trapped in the ship's structure when floating free. EPIRBs must be registered with the relevant authority in the flag state enabling details to be available to SAR authorities when requested. Registration may be based on the vessel MMSI, call sign or serial number using information included in the beacons 15 character hexadecimal identifier. Administrations are required to provide national registers available to the SAR services on a 24 hours/7 day basis.
FIGURE 33 EPIRB installed in a secure area of a ship and well clear of obstructions so that it can float free
Maritime-33
Maritime Manual
49
In January 2006, an International Beacon Registration Database (IBRD), (www.406registration.com) was made available by Cospas-Sarsat for use by those Administrations who are unable to provide a national beacon register, or those Administrations who wish to make their beacon registration data more widely available to SAR services by hosting it on the internet based IBRD. The 406 MHz beacons are designed with a self-test capability for evaluating key performance characteristics. Initiating the beacon self-test function will not generate a distress alert in the Cospas-Sarsat system. However, it will use some of the beacons limited battery power (the EPIRB is designed to operate for 48 hours) and should only be used in accordance with the beacon manufacturers guidance. It is a requirement of SOLAS Chapter IV that EPIRBs carried by ships conforming to the SOLAS Convention are tested at intervals not exceeding 12 months for their operation including a check on the frequency stability and power output. The procedures for the use of an EPIRB are to check that the mounting will allow it to float free, to check the battery expiry date and, if appropriate, to check the hydrostatic release expiry date.
5.6
The Radar Search and Rescue Transponder (SART) operates in the 9 GHz (3 cm wavelength) band and only transmits, assuming it is switched on, when interrogated by a radar. The SART should operate correctly when triggered by another ship's radar at distances of up to at least 5 nautical miles. Detection at longer ranges will be achieved from aircraft; at 3 000 ft. for example, the aircraft radar should elicit a useful response up to 30 nautical miles away from the SART. The transmission produces a distinctive line on the radar display of 12 blips extending out from the location of the SART along the line of bearing. These change to concentric circles when the SAR unit reaches the SART (see Fig. 34). To ensure that the SART transmission will be receivable over a useful distance it is essential that the SART be mounted at least 1 metre above sea level (see Fig. 35). The SART signal on the radar display may be more easily identified, especially if clutter or many other targets are present, by detuning the ships radar. Detuning reduces the intensity of return echoes on the display but allows the SART signal to be seen more easily since the SART emits a broadband signal which detuning does not affect to the same degree. Care should be taken in operating the radar detuned however as other wanted navigational and anti-collision information may be removed.
50
Maritime Manual
Radar display showing the SART 12 dot blip code (bearing approximately 90)
As the search craft approaches to within about 1nautical mile of the SART the 12 dots will change to wide arcs
The wide arcs change into complete circles as the SART is closed
Maritime-34
FIGURE 35 SART supplied with a telescopic mast to enable it to be deployed above a life-raft. In a large life-raft it may be possible to hang the SART from the roof and attain a 1 metre height. The AIS-SART which works with the ships AIS rather than the radar is illustrated in Fig. 45
Maritime-35
Maritime Manual
51
6
6.1
The method of distress alerting depends on the sea area in which the ship is sailing and on the equipment carried. The likely methods of initiating a distress alert in the four sea areas defined according to the coverage of MF, HF and VHF coast radio services and satellite services are shown in Table 3. Full details of the frequencies available for use in the GMDSS are given in Chapter 7. TABLE 3 Frequencies and methods for distress alerting
Sea area A1 Frequency 156.525 MHz 156.8 MHz 2 187.5 kHz A2 156.525 MHz 156.8 MHz 2 187.5 kHz 8 414.5 kHz and other HF DSC frequencies: 4 207.5 kHz, 6 312 kHz, 12 577 kHz and 16 804.5 kHz 156.525 MHz 156.8 MHz 1 530 1 544 MHz 1 626.5 1 646 MHz 2187.5 kHz 8 414.5 kHz and other HF DSC frequencies: 4 207.5 kHz, 6 312 kHz, 12 577 kHz and 16 804.5 kHz 156.525 MHz 156.8 MHz Description of usage CH 70 for DSC CH 16 for RT DSC CH 70 for DSC CH 16 for RT DSC DSC
A3
A4
52
Maritime Manual
The 406 MHz EPIRB is also suitable for initiating a distress alert in all sea areas. IMO publishes a GMDSS operating guidance card which is reproduced as Fig. 36. This describes the sequence of events for the situation of an incident where it is immediately necessary to abandon ship, where there is time to establish communication and where a situation is developing and an urgency call is more appropriate. Ships that conform to the SOLAS Convention are required to display this card at the operating position. The operational procedures for distress communications are described in the Radio Regulations, Article 32. The following terms are defined: a) b) c) the distress alert is a DSC distress call format or a distress message format in the case of satellite communications; the distress call is the initial voice or text procedure; the distress message is the subsequent voice or text procedure.
The transmission of a distress alert or a distress call indicates that the ship or person is threatened by grave and imminent danger and requires immediate assistance and is sent only on the authority of the person responsible for the ship. All stations which receive a distress alert or call are required to immediately cease any transmission capable of interfering with distress traffic and prepare for subsequent distress traffic. The procedure for a distress alert and a distress call for VHF communication is summarised in Fig. 37. Ships fitted with DSC initiate the distress alert by means of the dedicated distress button, if provided (see Fig. 38). The alert is then followed up by a distress call on channel 16, ideally after a pause of about 20 seconds in order to allow receiving personnel time to react. The form of the distress call is as follows (the word MAYDAY is pronounced as the French expression maider): the distress signal MAYDAY, spoken three times; the words THIS IS; the name of the vessel in distress, spoken three times; the call sign or other identification; the MMSI (if the initial alert has been sent by DSC).
Maritime Manual
Transmit, if time allows, distress call by HF/MF/VHF DSC or INMARSAT Embark in survival craft with VHF, SART and if possible EPIRB Switch on EPIRB and SART immediately and leave on
No No
No No
1. The EPIRB should float free and activate automatically if it cannot be taken into survival craft. 2. Where necessary, ships should use any appropriate means to alert other ships. 3. Nothing above is intended to preclude the use of any and all available means of distress alerting.
Channel 70 2 187.5 kHz 4 207.5 kHz 6 312 kHz 8 414.5 kHz 12 577 kHz
Channel 16 2 182 kHz 4 125 kHz 6 215 kHz 8 291 kHz 12 290 kHz
2 174.5 kHz 4 177.5 kHz 6 268 kHz 8 376.5 kHz 12 520 kHz
53
maritime-36
54
Maritime Manual
DISTRESS
RED BUTTON
until acoustic and light-indication becomes steady (more than 3 seconds)
MAYDAY-MAYDAY-MAYDAY
THIS IS
OWN ID
SHIP'S NAME:
CALL SIGN:
MMSI
(if the initial alert is sent by DSC)
MMSI:
MAYDAY
NAME of the VESSEL in distress CALL SIGN or other IDENTIFICATION MMSI
(if the initial alert is sent by DSC)
POSITION
given as latitude and longitude or if latitude and longitude are not known or if time is insufficient, in relation to a known geographical location NATURE of distress Kind of ASSISTANCE required Any other useful INFORMATION
2174.5 kHz 4177.5 kHz 6268.0 kHz 8376.5 kHz 12520.0 kHz 16695.0 kHz
Remember to use the correct HF-procedures Don't forget your EPIRB is the secondary means of alerting
Maritime-37
Maritime Manual
55
The distress call is followed by the distress message in the following form: the distress signal MAYDAY; the name of the vessel in distress; the call sign or other identification; the MMSI (if the initial alert has been sent by DSC); the position, given as the latitude and longitude, or if the latitude and longitude are not known or if time is insufficient, in relation to a known geographical location; the nature of the distress; the kind of assistance required; any other useful information.
Maritime-38
56
Maritime Manual
With MF and HF a DSC distress alert is made and an acknowledgement awaited before the distress call is made as there is little watch now kept on the MF and HF radiotelephony frequencies. The procedure with Inmarsat C is similar except that the subsequent communications are made by telex. The RCC which receives the distress alert or call initiates the transmission of an acknowledgement and a shore-to-ship distress alert relay addressed, as appropriate, to all ships in the area, to a selected group of ships, or to a specific ship, by terrestrial and/or satellite means. The procedure on board a ship which receives a distress alert is summarised in Figs 39 and 40 for the cases of VHF/MF and the longer range HF. In all cases the procedure is to listen for distress traffic. If the ship is able to assist, it acknowledges to the ship in distress by radiotelephony on VHF or MF. At HF where distances may be much larger contact is made instead with the RCC. The form of the radiotelephone acknowledgement is: the distress signal MAYDAY; the name followed by the call sign, or the MMSI or other identification of the station sending the distress message; the words THIS IS; the name and call sign or other identification of the station acknowledging receipt; the word RECEIVED; the distress signal MAYDAY.
The circumstance may arise when a distress alert has been received but has not apparently been acknowledged by an RCC. Under these circumstances it may be appropriate for a ship to relay the distress alert. The form of the distress call relay is: the distress signal MAYDAY RELAY, spoken three times; ALL STATIONS or coast station name, as appropriate, spoken three times; the words THIS IS; the name of the relaying station, spoken three times; the call sign or other identification of the relaying station; the MMSI (if the initial alert has been sent by DSC) of the relaying station (the vessel not in distress).
NO
YES
RESET SYSTEM
YES
ACKNOWLEDGE THE ALERT BY RADIOTELEPHONY TO THE SHIP IN DISTRESS ON VHF CH 16 / 2182 kHz
NO
Note 1 INFORM CS AND/OR RCC
Remarks:
NOTE 1 Appropriate or relevant RCC and/or CS shall be informed accordingly. If further DSC alerts are received from the same source and the ship in distress is beyond doubt in the vicinity, a DSC acknowledgement may, after consultation with and RCC or CS, be sent to terminate the call.
NOTE 2 In no case is a ship permitted to transmit a DSC distress relay call on receipt of a DSC distress alert on either VHF channel 70 or MF channel 2 187.5 kHz.
CS = coast station
57
Maritime-39
NO
NO
DSC
RT
NBDP
Remarks:
NOTE 1 If it is clear the ship or persons in distress are not in the vicinity and/or other crafts are better placed to assist, superflous communications which could interfere with search and rescue activities are to be avoided. Details should be recorded in the appropriate logbook.
NOTE 2 The ship should establish communications with the station controlling the distress as directed and render such assistance as required and appropriate.
Maritime Manual
CS = coast station
Maritime Manual
59
This call is followed by a distress message which, as far as possible, repeats the information contained in the original distress alert or distress message. If no response is received to the relay an appropriate coast station or rescue co-ordination centre may be contacted by sending an individual distress alert relay by DSC, addressed solely to that station. Distress alert relays by DSC should not be sent to all ships as experience has shown that they can cause great confusion. Similarly, a ship should not acknowledge by DSC unless it is certain that there are no distress communications taking place and no response has been obtained by radiotelephony. A similar relay procedure may be used to assist a ship which is observed to be in distress and which is unable or incapable of participating in distress radio communications.
6.2
A distress alert is considered to be false if it was transmitted without any indication that a ship or person was in distress and required immediate assistance; i.e. the alert was: a) b) c) transmitted intentionally; not cancelled; not verified as a result of either the ships failure to keep watch on appropriate frequencies or its failure to respond to calls from an authorized rescue authority; repeated; or transmitted using a false identity.
d) e)
Administrations receiving a report of a false distress alert are required to take steps to ensure that the infringement does not recur. Administrations also are required to take practicable and necessary steps to ensure the avoidance of false distress alerts, including those transmitted inadvertently. No action is normally taken against any ship or mariner for reporting and cancelling a false distress alert. The procedure for cancellation is by radiotelephony on the distress and safety frequency in the same band on which the distress transmission was sent as follows: the call ALL STATIONS, spoken three times; the words THIS IS; the name of the vessel, spoken three times; the call sign or other identification; the MMSI (if the initial alert has been sent by DSC); PLEASE CANCEL MY DISTRESS ALERT OF time in UTC.
60
Maritime Manual
The band is then monitored and response to any communications concerning the distress transmission made as appropriate. Details of the steps to be taken to cancel the distress alert are given in Radio Regulations, Resolution 349 as follows: for VHF DSC 1 2 3 Reset the equipment immediately. Set to channel 16. Transmit a broadcast message to All Stations giving the ships name, call sign and maritime mobile service identity (MMSI), and cancel the false distress alert. Reset the equipment immediately. Tune for radiotelephony transmission on 2 182 kHz. Transmit a broadcast message to All Stations giving the ships name, call sign and MMSI, and cancel the false alert. Reset the equipment immediately. Tune for radiotelephony on the distress and safety frequency in each band in which a false distress alert was transmitted. Transmit a broadcast message to All Stations giving the ships name, call sign and MMSI, and cancel the false alert on the distress and safety frequency in each band in which the false distress alert was transmitted.
for MF DSC 1 2 3
for HF DSC 1 2 3
for Inmarsat ship earth stations Notify the appropriate rescue co-ordination centre that the alert is cancelled by sending a distress priority message by way of the same coast earth station through which the false distress alert was sent. Provide ship name, call sign and Inmarsat identity with the cancelled alert message. for Emergency position-indicating radiobeacons If for any reason, an emergency position-indicating radiobeacon (EPIRB) is activated inadvertently, contact the appropriate rescue co-ordination centre through a coast station or land earth station and cancel the distress alert.
Maritime Manual
61
6.3
The operational procedures for urgency and safety communications are described in the Radio Regulations, Article 33. Urgency and safety communications include: a) b) c) d) e) f) navigational and meteorological warnings and urgent information; ship-to-ship safety of navigation communications; ship reporting communications; support communications for search and rescue operations; other urgency and safety messages; and communications relating to the navigation, movements and needs of ships and weather observation messages destined for an official meteorological service.
Urgency communications have priority over all other communications, except distress. Safety communications shall have priority over all other communications, except distress and urgency. 6.3.1 Urgency communications
The urgency call and the urgency signal indicate that the ship has a very urgent message to transmit concerning the safety of a mobile unit or a person and is sent only on the authority of the person responsible for the ship. The following terms are defined: a) b) c) the urgency announcement is a DSC call using the urgency call format or an urgency message format in the case of satellite communications; the urgency call is the initial voice or text procedure; the urgency message is the subsequent voice or text procedure.
Urgency communications consist of an announcement, transmitted using DSC, followed by the urgency call and message transmitted using radiotelephony using the same frequencies as are used for distress communications. The form of the urgency call is: the urgency signal PAN PAN, spoken three times; the name of the called station or all stations, spoken three times; the words THIS IS; the name of the station transmitting the urgency message, spoken three times; the call sign or any other identification; the MMSI (if the initial announcement has been sent by DSC),
62
Maritime Manual
Ships not equipped with DSC may announce an urgency call and message by transmitting the urgency signal by radiotelephony on VHF channel 16, while taking into account that other stations outside VHF range may not receive the announcement. With satellite systems, a separate urgency announcement or call does not need to be made before sending the urgency message but instead the appropriate network priority access settings are used for sending the message. Urgency communications to support search and rescue operations need not be preceded by the urgency signal. 6.3.2 Safety communications
The safety call and the safety signal indicates that the calling station has an important navigational or meteorological warning to transmit. The following terms are defined: a) b) c) the safety announcement is a DSC call using a safety call format or a safety message format in the case of satellite communications; the safety call is the initial voice or text procedure; the safety message is the subsequent voice or text procedure.
Safety communications consist of a safety announcement, transmitted using DSC, followed by the safety call and message transmitted using radiotelephony using the same frequencies as are used for distress and urgency communications. The form of the safety call is: the safety signal SECURITE, spoken three times; the name of the called station or all stations, spoken three times; the words THIS IS; the name of the station transmitting the safety message, spoken three times; the call sign or any other identification; the MMSI (if the initial announcement has been sent by DSC),
followed by the safety message which may be sent on a working channel. However, in order to avoid unnecessary loading of the DSC frequencies, safety messages transmitted by coast stations in accordance with a predefined timetable are not announced by DSC. Safety messages which only concern vessels sailing in the vicinity should be announced using radiotelephony procedures only. Ship stations not equipped with DSC may announce a safety message by transmitting the safety call by radiotelephony on VHF channel 16, while taking into account that other stations outside VHF range may not receive the announcement. With satellite systems, a separate safety announcement or call does not need to be made before sending the safety message but instead the appropriate network priority access settings are used for sending the message.
Maritime Manual
63
Ship stations in receipt of a safety announcement or safety call and message monitor the frequency or channel indicated for the message and listen until they are satisfied that the message is of no concern to them. They shall not make any transmission likely to interfere with the message.
7
7.1
The radio spectrum is subdivided into nine frequency bands as shown in Table 4. The unit of frequency is the hertz (Hz). TABLE 4 Frequency bands
Band number 4 5 6 7 8 9 10 11 12 Symbols Frequency range (lower limit exclusive, upper limit inclusive) 3 to 30 kHz 30 to 300 kHz 300 to 3 000 kHz 3 to 30 MHz 30 to 300 MHz 300 to 3 000 MHz 3 to 30 GHz 30 to 300 GHz 300 to 3 000 GHz Corresponding metric subdivision Myriametric waves Kilometric waves Hectometric waves Decametric waves Metric waves Decimetric waves Centimetric waves Millimetric waves Decimillimetric waves Metric abbreviations for the bands B.Mam B.km B.hm B.dam B.m B.dm B.cm B.mm
NOTE 1 Band N (N = band number) extends from 0.3 10N Hz to 3 10N Hz. NOTE 2 Prefix: k = kilo (103), M = mega (106), G = giga (109).
Subdivisions of these bands are allocated for their use by one or more terrestrial or space radiocommunication services under specified conditions by an entry in the Table of Frequency Allocations which is contained in the Radio Regulations, Article 5. An example of a service is the maritime mobile service. Frequency bands may be allocated globally or to an ITU Radiocommunication Region as shown in Fig. 41. The services may be given primary or secondary categories where a secondary service means that its stations shall not cause interference to stations of the
64
Maritime Manual
primary service and cannot claim protection. An example of a band allocated globally to the maritime mobile service on a primary basis is 156.4875-156.5625 MHz which is VHF channel 16 and its two guard band channels 75 and 76. Other bands used by ships may be in mobile bands, such as the mobile-satellite band used by Inmarsat, in which case they are shared with other mobile services. Alternately, they may not be available for use in all regions or may be a secondary allocation. Special provisions and additional application of the allocations are described by footnotes to the Table of Frequency Allocations.
FIGURE 41 The three regions for the allocation of frequencies
170 160 140 120 100 80 60 40 20 B 0 20 40 60 80 100 120 140 160 180 A 75 170 60 40 30 20 0 20 30 40 REGION 3 60 170 C 160 140 120 100 80 60 40 B 20 0 A 20 40 60 80 100 120 140 160 180 REGION 3 60 170
C 75
60 REGION 2 40 30 20 0 20 30 40
REGION 1
Maritime-41
Frequencies are assigned to a user through authorization by an administration for a radio station to use the frequency. The procedures for the assignment of frequencies are given in the Radio Regulations, Article 4. Basically, Member States of the ITU are required to assign frequencies in accordance with the Table of Frequency Allocations and the provisions of the Radio Regulations in order to prevent interference.
Maritime Manual
65
7.2
The frequencies for the GMDSS are given in the Radio Regulations, Appendix 15 and are shown in Table 5. Any emission causing harmful interference to distress and safety communications on any of the discrete frequencies in the table is prohibited. Test transmissions on any of the frequencies should be kept to a minimum and before transmitting for purposes other than distress, stations should listen on the frequency to make sure that no distress transmissions are being sent. The operational procedures for the use of these frequencies are described in Chapters 5 and 6. Watch-keeping arrangements are described in the Radio Regulations, Article 31 as follows: Coast stations assuming a watch-keeping responsibility in the GMDSS maintain an automatic digital selective-calling watch on frequencies and for periods of time as indicated in the information published in the List of Coast Stations and Special Service Stations (List IV). Coast earth stations assuming a watch-keeping responsibility in the GMDSS maintain a continuous automatic watch for appropriate distress alerts relayed by satellite. Ship stations, where so equipped, while at sea, maintain an automatic digital selective-calling watch (see Fig. 42) on the appropriate distress and safety calling frequencies in the frequency bands in which they are operating. Ship stations, where so equipped, also maintain watch on the appropriate frequencies for the automatic reception of transmissions of meteorological and navigational warnings and other urgent information to ships. Ship earth stations, while at sea, maintain watch except when communicating on a working channel. Resulting from the amendments to the Radio Regulations from the World Radiocommunication Conference 2007, all ship stations should now, where practicable, maintain a watch on the frequency 156.8 MHz (VHF channel 16). This facilitates communication between ships complying with the SOLAS Convention and all other ships. In port areas there may be arrangements for ships to alternatively maintain watch on a port operations frequency when the port station is maintaining the channel 16 watch. National administrations may also authorize the use of 2 182 kHz for a calling frequency within the coastal regions under their authority for which a watch should then be maintained. For ships complying with the SOLAS Convention there are further detailed radiocommunication watch-keeping requirement given in Parts A-VIII and B-VIII of the Seafarers Training, Certification and Watchkeeping (STCW) Code (Published by IMO).
66
Maritime Manual
FIGURE 42 Ships are frequently fitted with a variety of equipment to keep watch for DSC, voice messages, safety information and navigation information. This view shows an array of receiving antennas on a large ship
Maritime-42
Maritime Manual
67 TABLE 5 (continued)
Notes May be used by aircraft to communicate with stations of the maritime mobile service for distress and safety purposes, including search and rescue.
Used exclusively for NAVTEX-type transmissions. Used for maritime safety information as an alternative to NAVTEX. MSI-HF is not now widely used. May be used for intercommunication between mobile stations engaged in coordinated search and rescue operations.
*6 215 *6 268 *6 312 6 314 *8 291 *8 376.5 *8 414.5 8 416.5 *12 290 *12 520 *12 577 12 579 *16 420 *16 695 *16 804.5 16 806.5 19 680.5 22 376 26 100.5
RT-COM NBDP-COM DSC MSI-HF RT-COM NBDP-COM DSC MSI-HF RT-COM NBDP-COM DSC MSI-HF RT-COM NBDP-COM DSC MSI-HF MSI-HF MSI-HF MSI-HF
68
Maritime Manual
TABLE 5 (continued)
Frequency (MHz) *121.5 Description of usage AERO-SAR Notes Used for distress and urgency for radiotelephony by aircraft. Ships may communicate with aircraft on 121.5 MHz for the purposes of distress and urgency only. May also be used for these purposes by survival craft and EPIRBs. Used by aircraft and by other mobile and land stations engaged in coordinated search and rescue operations. May be used for communication between ships and aircraft engaged in coordinated search and rescue operations. Used in the maritime mobile service for distress and safety calls using digital selective-calling. Used for ship-to-ship communications relating to the safety of navigation. Used for distress and safety communications by radiotelephony. Additionally may be used by aircraft for safety purposes only. Used for AIS-SART for use in search and rescue operations. Used for AIS-SART for use in search and rescue operations. Used exclusively by satellite EPIRBs in the Earth-tospace direction. Used for distress and safety purposes in the space-toEarth direction in the maritime mobile-satellite service. GMDSS distress, urgency and safety communications have priority in this band. In addition used for routine non-safety purposes. Use is limited to distress and safety operations, including feeder links of satellites needed to relay the emissions of satellite EPIRBs to earth stations and narrow-band (space-to-Earth) links from space stations to mobile stations. Used for distress and safety purposes in the Earth-tospace direction in the maritime mobile-satellite service. GMDSS distress, urgency and safety communications have priority in this band. In addition used for routine non-safety purposes.
123.1 156.3
AERO-SAR
VHF-CH06
*156.525 156.650 *156.8 VHF- CH70 VHF-CH13 VHF-CH16
*1 544-1 545
D&S-OPS
1 626.5-1 645.5
SAT-COM
Maritime Manual
69 TABLE 5 (end)
Notes Use (Earth-to-space) limited to distress and safety operations. Used by radar transponders to facilitate search and rescue.
Any emission capable of causing harmful interference to distress, alarm, urgency or safety communications on the frequencies denoted by an asterisk (*) is prohibited.
Legend:
AERO-SAR These aeronautical carrier (reference) frequencies may be used for distress and safety purposes by mobile stations engaged in coordinated search and rescue operations. DSC These frequencies are used exclusively for distress and safety calls using digital selective calling in accordance with No. 32.5 (see Nos. 33.8 and 33.32). MSI In the maritime mobile service, these frequencies are used exclusively for the transmission of maritime safety information (MSI) (including meteorological and navigational warnings and urgent information) by coast stations to ships, by means of narrow-band direct-printing telegraphy. MSI-HF In the maritime mobile service, these frequencies are used exclusively for the transmission of high seas MSI by coast stations to ships, by means of narrow-band direct-printing telegraphy. NBDP-COM These frequencies are used exclusively for distress and safety communications (traffic) using narrow-band direct-printing telegraphy. RT-COM These carrier frequencies are used for distress and safety communications (traffic) by radiotelephony. D&S-OPS The use of these bands is limited to distress and safety operations of satellite emergency position-indicating radio beacons (EPIRBs). SAT-COM These frequency bands are available for distress and safety purposes in the maritime mobile-satellite service (see Notes). VHF-CH# These VHF frequencies are used for distress and safety purposes. The channel number (CH#) refers to the VHF channel as listed in Appendix 18, which should also be consulted. AIS These frequencies are used by automatic identification systems (AIS), which should operate in accordance with the most recent version of Recommendation ITU-R M.1371. (WRC-07)
7.3
7.3.1
Satellite services provided by Inmarsat and other operators are generally automatic in operation. The shipboard equipment automatically keeps watch for incoming calls.
70
Maritime Manual
Outgoing calls are made using international telephone dialling codes, e-mail addresses or short codes supplied by the service operator. 7.3.2 VHF services
Some coast stations offer automatic public correspondence services in the VHF band using digital selective-calling. Details are given in the List of Coast Stations and Special Service Stations (List IV). Ships maintain watch for incoming calls on the frequency 156.525 MHz (channel 70) in the same way as watch is kept for distress and safety traffic. Outgoing calls are made using the VHF digital selective-calling equipment installed on the ship. Some coast stations offer manual services as given in the List of Coast Stations and Special Service Stations (List IV). The frequency 156.8 MHz (channel 16) may be used by coast and ship stations for call and reply and by coast stations to announce the transmission on another frequency of traffic lists and important maritime information. Ships then maintain watch on channel 16 in the same way as watch is kept for distress and safety traffic. Alternatively the coast station may use one of the channels designated in Appendix 18 to the Radio Regulations (see Table 6) for public correspondence as a calling channel. To facilitate the reception of distress calls and distress traffic, all transmissions on 156.8 MHz should be kept to a minimum and should not exceed one minute. Before transmitting on the frequency 156.8 MHz, a station should listen for a reasonable period to make sure that no distress traffic is being sent. 7.3.3 7.3.3.1 MF and HF services Use of digital selective-calling
The frequencies on which coast stations provide services using digital selective-calling and information concerning watch-keeping are given in the List of Coast Stations and Special Service Stations (List IV). Ships maintain an automatic digital selective-calling watch on one or more appropriate frequencies when within the coverage area of coast stations providing services using digital selective-calling. This will normally require additional digital selective-calling equipment to be carried on the ship. Bands between 1 606.5 kHz and 4 000 kHz When calling a coast station, ships should use a national digital selective-calling channel on which the coast station is maintaining watch or one of the international digital selective-calling frequencies. For the bands between 1 606.5 kHz and 4 000 kHz the international digital selective-calling frequency is 2 189.5 kHz. For coast stations the international digital-selective calling frequency is 2 177 kHz. A ship calling another ship should use the frequency 2 177 kHz for the call and acknowledgement.
Maritime Manual
71
Channel designator
Inter-ship
60 01 61 02 62 03 63 04 64 05 65 06 66 07 67 08 68 09 69 10 70 11 71 12 72 13 73 14 74 15 75
x x
72
Maritime Manual
TABLE 6 (end)
Transmitting frequencies (MHz) From ship stations 156.800 156.825 156.850 156.875 156.900 156.925 156.950 156.975 157.000 157.025 157.050 157.075 157.100 157.125 157.150 157.175 157.200 157.225 157.250 157.275 157.300 157.325 157.350 157.375 157.400 157.425 161.975 162.025 From coast stations 156.800 156.825 156.850 161.500 161.525 161.550 161.575 161.600 161.625 161.650 161.675 161.700 161.725 161.750 161.775 161.800 161.825 161.850 161.875 161.900 161.925 161.950 157.375 162.000 157.425 161.975 162.025 Port operations and ship movement Single frequency Two frequency Public correspondence
Channel designator
Inter-ship
16 76 17 77 18 78 19 79 20 80 21 81 22 82 23 83 24 84 25 85 26 86 27 87 28 88 AIS 1 AIS 2 *
x x x x x x x x x x x x x x x x x x x x
Added by the Radio Regulation Board until the necessary action is taken by a future WRC.
NOTE 1 Table 6 gives the major uses of the VHF channels. There are provisions within Appendix 18 for some alternative uses and also for the introduction of new technologies into the VHF band. Not all of the VHF channels are available for use everywhere in the world and administrations typically publish tables of the channels used in their coastal waters.
Maritime Manual
73
Bands between 4 000 kHz and 27 500 kHz In the bands between 4 000 kHz and 27 500 kHz, ships should choose an appropriate international digital selective-calling frequency, taking into account propagation characteristics, and maintain watch on an appropriate digital selective-calling frequency used by the coast station. There are paired frequencies available for the 4, 6, 8, 12, 16, 18, 22 and 25 MHz bands and the details are given in the List of Coast Stations and Special Service Stations (List IV). 7.3.3.2 Use of radiotelephony
The frequencies on which coast stations (see Fig. 43) provide services for radiotelephony and information concerning watch-keeping are indicated in the List of Coast Stations and Special Service Stations (List IV).
FIGURE 43 Rogaland Radio in Norway which provides a public correspondence service as described in List IV
Maritime-43
74
Maritime Manual
Bands between 1 606.5 kHz and 4 000 kHz If coast stations are not equipped with digital selective-calling, the frequency 2 182 kHz may be used for call and reply and by coast stations to announce the transmission, on another frequency, of traffic lists. To facilitate the use of the frequency 2 182 kHz for distress purposes, all transmissions on 2 182 kHz should be kept to a minimum and should not exceed one minute. Before transmitting, a station should listen for a reasonable period to make sure that no distress traffic is being sent. Coast stations which use 2 182 kHz for calling are required to be able to use at least one other frequency in the bands between 1 606.5 kHz and 2 850 kHz. Ship stations should be able to send and receive on a carrier frequency of 2 182 kHz, send, in addition, on at least two working frequencies and receive on all other frequencies necessary for their service. In Region 1, ships should be able to use the ship-to-shore carrier frequency 2 045 kHz as a working frequency, and the carrier frequency 2 048 kHz as an inter-ship frequency. In Regions 2 and 3, ships should be able to use the carrier frequencies 2 635 kHz and 2 638 kHz for inter-ship frequencies. Bands between 4 000 kHz and 27 500 kHz If coast stations are not equipped for digital selective-calling and calling by radiotelephony is necessary, it should be done on the working frequencies assigned to the coast stations or on the calling frequencies listed below. Ship station Carrier frequency 4 125 kHz 6 215 kHz 8 255 kHz 12 359 kHz 16 537 kHz 18 795 kHz 22 060 kHz 25 097 kHz Coast station Carrier frequency 4 417 kHz 6 516 kHz 8 779 kHz 12 359 kHz 16 537 kHz 19 770 kHz 22 756 kHz 26 172 kHz
All ship stations should be able to send and receive on the carrier frequencies 4 125 kHz and 6 215 kHz. Before transmitting on these carrier frequencies a station should listen on the frequency for a reasonable period to make sure that no distress traffic is being sent. The frequencies to be used for the conduct of simplex radiotelephony and, for the conduct of duplex telephony, the pairs of transmitting frequencies of the coast stations and of the corresponding ship stations are given in the Radio Regulations, Appendix 17
Maritime Manual
75
(Frequencies and channelling arrangements in the high frequency bands for the maritime mobile service). An indication of the channels available for two frequency operation is given below. Channel numbers 401 429 601 608 801 837 1601 1656 1801 1815 2201 2253 2501 2510 Band 4 MHz 6 MHz 8 MHz 16 MHz 18/19 MHz 22 MHz 25/26 MHz
8
8.1
The authority of the master is described in the Radio Regulations, Article 46. The service of a ship station is placed under the supreme authority of the master or of the person responsible for the ship. The person holding this authority requires that each operator comply with the Radio Regulations and that the ship station for which the operator is responsible is used, at all times, in accordance with the Radio Regulations. The master or the person responsible, as well as all persons who may have knowledge of the text or even of the existence of a radiotelegram, or of any information obtained by means of the radiocommunication service, are placed under the obligation of observing and ensuring the secrecy of correspondence.
8.2
Operators certificates
Operators certificates are described in Article 47 of the Radio Regulations which requires that every ship station shall be controlled by an operator holding a certificate recognised by the government to which the ship station is subject. However, providing the station is so controlled, other persons beside the holder of the certificate are permitted to use the equipment. The Article defines six classes of operator certificate, namely: First-class Radio-Electronic Certificate Second-class Radio-Electronic Certificate General Operators Certificate (GOC) (includes full on board maintenance), (includes limited on-board maintenance), (for all sea areas, but not including maintenance),
76
Maritime Manual
Restricted Operators Certificate (ROC) Long Range Certificate (LRC) Short Range Certificate (SRC)
(for sea area A1 ships only), (for ships which are not required to comply with the SOLAS Convention), (for VHF operation only on ships which are not required to comply with the SOLAS Convention).
Certificates are issued and authorized by administrations. Certificates include the holders signature, photograph and date of birth.
8.3
Personnel
Radio Regulations, Article 48 requires that personnel of ship stations and ship earth stations are adequately qualified and certificated (see Fig. 44). For ships which are not required to comply with the SOLAS Convention the operators certificate is the Long Range Certificate (LRC) or, if the ship sails within sea area A1 only, the Short Range Certificate (SRC). For ships which are required to comply with the SOLAS Convention the operators certificate is the first- or second- class radio electronic certificate or a general operator's certificate (GOC), or, if the ship sails within sea area A1 only, the restricted operator's certificate (ROC). However, it should be noted that an ROC covers only the operation of GMDSS equipment required for sea area A1, and does not cover the operation of A2/A3/A4 equipment fitted on a ship over and above the basic A1 requirements, even if the ship is in a sea area A1. SOLAS Chapter IV, regulation 16 requires every ship to carry personnel qualified for distress and safety radiocommunication purposes, any one of whom can be designated to have primary responsibility for radiocommunications during distress incidents. In passenger ships, at least one person has to be assigned to perform only radiocommunication duties during distress incidents. The International Convention on Standards of Training, Certification and Watchkeeping (STCW Convention), further requires that all deck officers hold an appropriate certificate related to the GMDSS which in practice is the GOC. Deck officers are further required, in addition to the GOC requirements, to have a knowledge of the search and rescue procedures of the IAMSAR Manual, the means to prevent the transmission of false alerts, ship reporting systems, radio medical services, the use of the International Code of Signals and the Standard Marine Communication Phrases (Published by IMO as Assembly Resolution A.918(22)), and the English language.
Maritime Manual
77
FIGURE 44
Example of the certificate indicating successful completion of training in GMDSS radiocommunications and the General Operators Certificate which is then issued to the candidate by the authorities in the United Kingdom
Maritime-44
9
9.1
Identification of stations
Formation and use of call signs and MMSI
Radio Regulations, Article 19 describes the identification of stations which ensures that all transmissions in the mobile services are capable of being identified by identification signals. Ships operating in the GMDSS are assigned a 9-digit identification number, called the Maritime Mobile Service Identity (MMSI). The MMSI is programmed into all DSC equipment and is included automatically in each call. Included in the MMSI are the Maritime Identification Digits (MID) which identify the country licensing/controlling the station. Ships may also be assigned a Call Sign. The international series of MIDs and Call Signs are allocated by the Secretary-General of the ITU to administrations.
78
Maritime Manual
Administrations are required to ensure that suitable arrangements are made for assigning and registering identities used by ships, and make registration information available to rescue co-ordination centres on a 24 hours /7 day basis. The types of MMSI are described in Recommendation ITU-R M.585 which details six types: M1I2D3X4X5X6X7X8X9 01M2I3D4X5X6X7X8X9 0102M3I4D5X6X7X8X9 111213M4I5D6X7X8X9 9192M3I4D5X6X7X8X9 9182M3I4D5X6X7X8X9 for ship station identity for group ship station call identities for calling simultaneously more than one ship for coast station identity for SAR aircraft for AIS Aids to Navigation (AtoN) for craft associated with a parent ship
Additionally the AIS-SART (see Fig. 45) has an identification number which is similar to an MMSI of the form: 917203Y4Y5X6X7X8X9 where Y4Y5 is a manufacturer identity and X6X7X8X9 is a serial number
FIGURE 45 The AIS-SART uses an identification number similar to a MMSI so that it can be received by a ships AIS. The AIS-SART is used in the same way as the radar SART to facilitate the location of survivors
Maritime-45
Maritime Manual
79
AIS-SART identities are not registered by administrations but the structure ensures that each AIS-SART has a unique identity (the manufacturer identity is administered by CIRM). When a ship changes from the flag of registration of one administration to another it will be necessary to obtain a new MMSI and a new Call Sign for the ship. Users should check that the details have been programmed into the GMDSS equipment on board. Administrations should ensure that the changes are notified to the ITU Radiocommunication Bureau as soon as possible so that the data published in the List of ship stations and maritime mobile service identity assignments (List V) and on the MARS database can be updated.
9.2
Call signs (see Fig. 46) are assigned to ships by a responsible administration and are based on a 3-character call sign series allocated by the ITU to this administration. Call signs serve for the identification of radio stations and installations and are given in the Radio Regulations, Appendix 42 (see Annex 3). Call signs for any particular purpose are then composed using the applicable root characters and rules set down in Article 19.
FIGURE 46 Example of a call sign. This information is typically prominently displayed on a card on the bulk head adjacent to the radio station
C6SES
MMSI 311317000
Maritime-46
Even ships without a radio installation may be assigned Visual Signal Letters (VSL) with which they may identify themselves by means of flags or an Aldis lamp (using Morse code). VSLs are formed in the same way as call signs. It is not compulsory to assign call signs to stations identified by MMSIs.
9.3
Maritime Identification Digits (MIDs) are allocated to administrations and the geographical area of the administration responsible for the station. For the moment
80
Maritime Manual
digits one and eight in the first position of an MID are reserved for future use. Digit nine in the first position of an MID is used for special purposes. The complete list of MIDs is given in Annex 4. The Secretary-General of the ITU will allocate a new MID to an administration when the combinations of numbers have been largely used. Some administrations (see Annex 4 of this Manual) therefore, have more than one MID. Before 1 February 2002, ship stations which required automatic access on a worldwide basis to public switched networks were assigned MMSIs with three trailing zeros. Each MID then only had capacity for 1 000 ships but now satellite networks adopt their own numbering systems. MMSIs which are no longer in use may be re-used after a period of five years.
10
10.1
The ITU Constitution, Article 40 requires that international telecommunication services must give absolute priority to all telecommunications concerning safety of life at sea, on land, in the air or in outer space, as well as to epidemiological telecommunications of exceptional urgency of the World Health Organization (WHO). Article 46 of the ITU Constitution further requires that radio stations shall be obliged to accept, with absolute priority, distress calls and messages regardless of their origin, to reply in the same manner to such messages, and immediately to take such action in regard thereto as may be required. The Radio Regulations, Article 53 describes the order of priority of communications. All stations in the maritime mobile service and the maritime mobile-satellite service are required to be capable of offering four levels of priority in the following order: 1 Distress. 2 Urgency. 3 Safety. 4 Other. In a fully automated system, where it is impracticable to offer all four levels of priority, category 1 shall receive priority. As described in Chapter 5, the older designs of Inmarsat terminals (Inmarsat B and Inmarsat C) do not have the four levels of priority, particularly in the shore-to-ship direction. However, the newer Inmarsat Fleet terminals do provide the four levels.
10.2
Inspection of stations
Article 49 of the Radio Regulations describes inspection of stations. When a ship visits a foreign port, the local government or its administration is entitled to examine the
Maritime Manual
81
licence of the ship station. If the licence cannot be produced or if irregularities are observed, the government is entitled to inspect the radio installations to check that they conform to the conditions of the Radio Regulations. In addition, inspectors have the right to require the production of operators certificates. If infringements to the regulations are detected then these are reported to the administration of the country having jurisdiction over the station. It is the responsibility of this administration to take the necessary action. Ships conforming to the SOLAS Convention are also subject to a system of port state control (see Fig. 47) where inspectors check that the ship complies with the conventions of the IMO which may include an inspection of the radio station against the requirements of SOLAS. In cases of serious infringement the ship may be prevented from sailing until remedial action has been taken.
FIGURE 47 Inspector at work on a large passenger vessel
Maritime-47
10.3
Article 50 of the Radio Regulations requires a ship station to have an accurate clock correctly regulated to Coordinated Universal Time (UTC). However, with the common availability of UTC on board ships derived from the ships navigation equipment, it is no longer a requirement to have a dedicated clock for the radio station. UTC is required to be used for all entries into the radiocommunication service log (see 10.6).
82
Maritime Manual
10.4
Interferences
Radio Regulations, Article 15 describes procedures for minimizing interference, that is the effect of unwanted energy in emissions on reception in a radiocommunication system manifested by a performance degradation, misinterpretation or loss of information. As a general rule, stations should not carry out unnecessary transmissions, only radiate as much power as is necessary, not transmit superfluous or false or misleading signals or transmit signals without identification. The ITU Constitution, Article 47 demands that Member States agree to take the steps required to prevent the transmission or circulation of deceptive distress, urgency safety or identification signals, and to collaborate in locating and identifying stations under their jurisdiction transmitting such signals. The ITU Constitution, Article 45 requires that all stations be established and operated in such a manner as to not cause harmful interference. The Radio Regulations define harmful interference as interference which endangers the functioning of a radionavigation service or of other safety services or seriously degrades, obstructs or repeatedly interrupts a radiocommunication service. There are procedures in the Radio Regulations, Article 15 for Member States to follow to settle problems of harmful interference. To help in the prompt elimination of harmful interference, administrations cooperate in the continued development of the international monitoring system (see Fig. 48). Administrations are also required to take all practicable and necessary steps to ensure that the operation of electrical apparatus or installations of any kind, including power and telecommunication distribution networks does not cause interference. For ships conforming to the SOLAS Convention there is a further requirement in SOLAS Chapter V that all electrical and electronic equipment on the bridge or in the vicinity of the bridge be tested for electromagnetic compatibility to the requirements of standard IEC 60945 (published by the IEC). To ensure technical compliance with the Radio Regulations for interferences, administrations are required to arrange for frequent checks to be made of the emissions of stations under their jurisdiction. Ships conforming to the SOLAS Convention are required to have an annual radio survey which includes a check on emissions.
10.5
Secrecy
The ITU Constitution, Article 37 demands that Member States agree to take all possible measures with a view to ensuring the secrecy of international correspondence.
Maritime Manual
83
For radiocommunications, Radio Regulations, Article 17 requires that administrations bind themselves to take the necessary measures to prohibit and prevent: a) b) the unauthorized interception of radiocommunications not intended for the general use of the public; the divulgence of the contents, simple disclosure of the existence, publication or any use whatever, without authorization of information of any nature whatever obtained by the interception of the radiocommunications mentioned above.
This requirement is realized through the licence for the radio station as described in Chapter 3 where the holder of the licence is required to preserve the secrecy of telecommunications.
FIGURE 48 View of Baldock radio monitoring station in the United Kingdom which contributes to the international monitoring system. Very evident is the large rotatable antenna used for the investigation and resolution of interference to international radio circuits at HF
Maritime-48
84
Maritime Manual
10.6
The Radio Regulations, Article 51 requires ships (other than survival craft) to carry documents as detailed in Appendix 16. For ships conforming to the SOLAS Convention, the station should be provided with: 1 2 3 the licence prescribed by Article 18 (see Chapter 3); certificates of the operator or operators (see Chapter 8); a log in which the following are recorded as they occur, together with the time of the occurrence, unless administrations have adopted other arrangements for recording all information which the log should contain: a) a summary of communications relating to distress, urgency and safety traffic; b) a reference to important service incidents; 4 5 6 the List of Ship Stations and Maritime Mobile Service Identity Assignments (List V) in either printed or electronic format; the List of Coast Stations and Special Service Stations (List IV) in either printed or electronic format; the Manual for Use by the Maritime Mobile and Maritime Mobile-Satellite Services in either printed or electronic format.
An administration may, however, exempt a ship from the carriage of the documents mentioned in items 5 and 6 above under various circumstances (for example, when that ship carries equivalent information for the ships specified trading area). For ships which do not conform to the SOLAS Convention but which are required to carry a radio installation by other agreements, the above applies except that carriage of the List of Ship Stations and Maritime Mobile Service Identity Assignments (List V) is not a requirement. All ship stations should carry at least the documents in items 1 and 2. Ships conforming to the SOLAS Convention are also required by SOLAS Chapter V to carry the International Code of Signals and Volume III of the International Aeronautical and Maritime Search and Rescue (IAMSAR) Manual. Examples of documents published by the ITU are shown in Fig. 49.
Maritime Manual
85
Maritime-49
10.7
When it is necessary to spell out call signs, service abbreviations and words, the following letter spelling table given in the Radio Regulations, Appendix 14 should be used: Spoken as(1) AL FAH BRAH VOH CHAR LEE or SHAR LEE DELL TAH ECK OH FOKS TROT
Letter to be transmitted A B C D E F
86
Maritime Manual
G H I J K L M N O P Q R S T U V W X Y Z
(1)
Golf Hotel India Juliett Kilo Lima Mike November Oscar Papa Quebec Romeo Sierra Tango Uniform Victor Whiskey X-ray Yankee Zulu
GOLF HOH TELL IN DEE AH JEW LEE ETT KEY LOH LEE MAH MIKE NO VEM BER OSS CAH PAH PAH KEH BECK ROW ME OH SEE AIR RAH TANG GO YOU NEE FORM or OO NEE FORM VIK TAH WISS KEY ECKS RAY YANG KEY ZOO LOO
When it is necessary to spell out figures or marks, the spelling table given in Appendix 14 is not widely used and it is preferable to use the table given in the IMO Standard Marine Communication Phrases: Figure or mark to be transmitted 0 1 2 3 4 5 6 7 Code word to be used Zero One Two Three Four Five Six Seven Spoken as(1) ZEE RO WUN TOO TREE FOW ER FIFE SIX SE VEN
Maritime Manual
(1)
8 Eight 9 Nine Decimal point Decimal Full stop Stop The syllables to be emphasized are underlined.
However, stations of the same country, when communicating between themselves, may use any other table recognized by their administration.
11
11.1
Related publications
ITU publications
List IV List of Coast Stations and Special Service Stations This List is published every two years in two complementing parts: The first part is a paper publication that contains, among others, those coast stations participating in MF, HF and VHF watch-keeping using DSC techniques, Rescue co-ordination centres, VTS and pilot stations, coast stations providing public correspondence service, stations transmitting ships navigational and meteorological warnings and MSI information, stations transmitting notice to navigators and radio time signals. The second part is a CD-ROM publication that contains the information published in the paper publication as well as information concerning port stations, coast earth stations and NAVAREA coordinators.
The data provided includes the name of the station, their relevant frequencies and geographical coordinates, MMSI and/or call sign, the hours of service and other pertinent information. The stations are listed under their corresponding administration/geographical area (ISBN 92-71-16031-2). List V List of Ship Stations and Maritime Mobile Service Identity Assignments This List is published annually in two complementing parts: The first part is a paper publication that contains information pertaining to all ship stations assigned an MMSI (with the exception of pleasure craft), all coast stations assigned an MMSI, SAR aircraft assigned an MMSI as well as contact information concerning Accounting Authorities that act as a billing intermediary between the maritime mobile station and service providers. The second part is a CD-ROM publication that contains the information published in the paper publication as well as information concerning all other ship stations that have been notified to the Radiocommunication Bureau. Also included in this CD-ROM is a database containing all ship stations and a
88
Maritime Manual
software interface that allows users to retrieve all the data notified for a ship station. The data provided in this list ranges from the ships MMSI, name, call sign, IMO number and the radio installations on board the vessel, to the name, frequencies available for communications and geographical coordinates of a coast station or the type and maritime radio equipment onboard aircraft that are used for SAR activities (ISBN 92-71-34033-7). Manual for Use by the Maritime Mobile and Maritime Mobile-Satellite Services (Volume 2) Volume 2 of the Manual for Use by the Maritime Mobile and Maritime Mobile-Satellite Services contains provisions designed to be of use to operators. Volume 2 contains extracts from: the Constitution and Convention of the ITU; the Radio Regulations; ITU-R Recommendations; the International Telecommunication Regulations; ITU-T Recommendations. (ISBN 92-61-12671-5).
ITU-R Recommendations and Reports Available as a DVD-ROM, this disk contains all the ITU-R Recommendations and Reports in force and available at the publication date. The files are available in Adobe Acrobat PDF format, as well as in their original Word for Windows format (ISBN 92-61-13047-X). Radio Regulations The Radio Regulations, Edition of 2008, contains the complete texts of the Radio Regulations as adopted by the World Radiocommunication Conference (Geneva, 1995) (WRC-95) and subsequently revised and adopted by the World Radiocommunication Conference (Geneva, 1997) (WRC-97), the World Radiocommunication Conference (Istanbul, 2000) (WRC-2000), the World Radiocommunication Conference (Geneva, 2003) (WRC-03), and the World Radiocommunication Conference (Geneva, 2007) (WRC-07), including all Appendices, Resolutions, Recommendations and ITU-R Recommendations incorporated by reference (ISBN 92-61-12467-4). All ITU publications www.itu.int/publications. can be purchased on the following website:
Maritime Manual
89
11.2
IMO publications
Global Maritime Distress and Safety System Manual The GMDSS Manual is a single comprehensive publication which includes: description of the development, components and the concepts of the GMDSS; the carriage requirements and the operational procedures, excerpts from the relevant SOLAS regulations for the GMDSS, supporting resolutions and circulars relevant to the GMDSS; the IMO performance standards and related ITU-R Recommendations giving the technical detail of the radio equipment, the NAVTEX Manual, the International SafetyNET Manual and the revised Joint IMO/IHO/WMO Manual on Maritime Safety Information; the current GMDSS Master Plan giving the details of the coastal infrastructure and services provided by member administrations; and extracts from the ITU-R Radio Regulations giving the radio regulatory background.
The Manual is intended for use by ship personnel, shore operators, trainers, administrations, regulators and anyone else concerned with ship communication (ISBN 978-92-801-15086). International Aeronautical and Maritime Search and Rescue Manual (IAMSAR Manual) Jointly published by IMO and ICAO, the three-volume IAMSAR Manual provides guidelines for a common aviation and maritime approach to organizing and providing search and rescue (SAR) services. Each volume can be used as a stand-alone document or, in conjunction with the other two volumes, as a means to attaining a full view of the SAR system. The three volumes came into force on 1 June 2008: Volume I Organization and Management, discusses the global SAR system concept, establishment and improvement of national and regional SAR systems and co-operation with neighbouring States to provide effective and economical SAR services (ISBN 978-92-801-14881); Volume II Mission Coordination, assists personnel who plan and coordinate SAR operations and exercises (ISBN 978-92-801-14898); Volume III Mobile Facilities, is intended to be carried aboard rescue units, aircraft and vessels to help with performance of a search, rescue or on-scene co-ordinator function, and with aspects of SAR that pertain to their own emergencies (ISBN 978-92-801-14904).
90
Maritime Manual
International Convention on Search and Rescue The International Conference on Maritime Search and Rescue, in April 1979, concerned the establishment of an International Maritime Search and Rescue (SAR) plan covering the needs for ship reporting systems, SAR services and the Rescue of persons in distress at sea. The current edition includes amendments which were adopted in May 2004 and came into force on 1 July 2006 (ISBN 978-92-801-52067). International Code of Signals The Code is intended for communications between ships, aircraft and authorities ashore during situations related essentially to the safety of navigation and persons; it is especially useful when language difficulties arise. The Code is suitable for transmission by all means of communication, including radiotelephony and radiotelegraphy (ISBN 978-92-801-41986). International Convention for the Safety of Life at Sea The current edition presents a consolidated text of the SOLAS, 1974 Convention, its Protocols of 1978 and 1988 and all amendments in effect from that date. SOLAS is an essential reference for maritime administrations, ship manufacturers, owners and operators, shipping companies, education institutes and all others concerned with requirements of the International Convention for the Safety of Life at Sea (ISBN 978-92-801-15055). International Convention on Watchkeeping (STCW 1978) Standards of Training, Certification and
The Convention, articles and annex provide the legal framework within which mandatory technical standards contained in part A of the STCW Code are applied. Part B of the Code provides guidance to assist those who are involved in educating, training or assessing the competence of seafarers or who are otherwise involved in applying STCW Convention provisions (ISBN 978-92-801-51084). International SafetyNET Manual SafetyNET is a satellite-based international automatic direct-printing service for the promulgation of maritime safety information (MSI) to ships. The ability to receive SafetyNET service information is generally necessary for all ships which sail beyond coverage of NAVTEX and is commended to all Administrations having responsibility for maritime affairs and to mariners who require an effective MSI service in waters not served by NAVTEX (ISBN 978-92-801-41597). IMO Standard Marine Communication Phrases The ability to use and understand the IMO Standard Marine Communication Phrases (SMCP) is required for the certification of officers in charge of a navigational watch on ships of 500 gross tonnage or more.
Maritime Manual
91
The phrases are divided into Part A and Part B. Part A covers phrases to be applied according to the requirements of table A-II/1 (minimum competence of officers in charge of a navigational watch on ships of 500 gross tonnage) of the STCW Code. This part is enriched by essential phrases concerning ship handling and safety of navigation to be used in on-board communications. Part B calls attention to other on-board standard safety-related phrases which, supplementary to Part A, may also be regarded as useful for maritime English instruction. A separate pronunciation guide, as software on a compact disc, that can be used in a personal computer is attached to this book (ISBN 978-92-801-51374). NAVTEX Manual NAVTEX is an international automated direct-printing service for promulgation of navigational and meteorological warnings and urgent information to ships. This Manual is intended for use by seafarers, shipowners, maritime Administrations and others concerned with the preparation, broadcasting and reception of maritime safety information (ISBN 978-92-801-42020). Performance Standards for Shipborne Radiocommunications and Navigational Equipment The current consolidated edition incorporates all amendments adopted up to November 2007 including: Electronic Chart Display and Information Systems (ECDIS), Integrated Navigation Systems, shipborne GALILEO receiver equipment, survival craft AIS search and rescue transmitters (AIS-SART), functional requirements for long-range identification and tracking of ships, shipborne voyage data recorders (VDRs) and shipborne simplified voyage data recorders (S-VDRs), navigation lights, navigation light controllers and associated equipment, provision of radio services for the GMDSS (ISBN978-92-801-42341).
92
Maritime Manual
space radiocommunication: Any radiocommunication involving the use of one or more space stations or the use of one or more reflecting satellites or other objects in space. radiodetermination: The determination of the position, velocity and/or other characteristics of an object, or the obtaining of information relating to these parameters, by means of the propagation properties of radio waves. radionavigation: Radiodetermination used for the purposes of navigation, including obstruction warning. radio astronomy: Astronomy based on the reception of radio waves of cosmic origin. Coordinated Universal Time (UTC): Time scale, based on the second (SI), as defined in Recommendation ITU-R TF.460-6. For most practical purposes associated with the Radio Regulations, UTC is equivalent to mean solar time at the prime meridian (0 longitude), formerly expressed in GMT.
Maritime Manual
allocation (of a frequency band): Entry in the Table of Frequency Allocations of a given frequency band for the purpose of its use by one or more terrestrial or space radiocommunication services or the radio astronomy service under specified conditions. This term shall also be applied to the frequency band concerned. allotment (of a radio frequency or radio frequency channel): Entry of a designated frequency channel in an agreed plan, adopted by a competent conference, for use by one or more administrations for a terrestrial or space radiocommunication service in one or more identified countries or geographical areas and under specified conditions. assignment (of a radio frequency or radio frequency channel): Authorization given by an administration for a radio station to use a radio frequency or radio frequency channel under specified conditions. Radio services radiocommunication service: A service involving the transmission, emission and/or reception of radio waves for specific telecommunication purposes. mobile service: A radiocommunication service between mobile and land stations, or between mobile stations. mobile-satellite service: A radiocommunication service: between mobile earth stations and one or more space stations, or between space stations used by this service; or between mobile earth stations by means of one or more space stations.
maritime mobile service: A mobile service between coast stations and ship stations, or between ship stations, or between associated on-board communication stations; survival craft stations and emergency position-indicating radiobeacon stations may also participate in this service. maritime mobile-satellite service: A mobile-satellite service in which mobile earth stations are located on board ships; survival craft stations and emergency positionindicating radiobeacon stations may also participate in this service. port operations service: A maritime mobile service in or near a port, between coast stations and ship stations, or between ship stations, in which messages are restricted to those relating to the operational handling, the movement and the safety of ships and, in emergency, to the safety of persons. ship movement service: A safety service in the maritime mobile service other than a port operations service, between coast stations and ship stations, or between ship stations, in which messages are restricted to those relating to the movement of ships radio astronomy service: A service involving the use of radio astronomy.
94
Maritime Manual
safety service: Any radiocommunication service used permanently or temporarily for the safeguarding of human life and property. Radio stations and systems station: One or more transmitters or receivers or a combination of transmitters and receivers, including the accessory equipment, necessary at one location for carrying on a radiocommunication service, or the radio astronomy service. terrestrial station: A station effecting terrestrial radiocommunication. earth station: A station located either on the Earths surface or within the major portion of the Earths atmosphere and intended for communication: with one or more space stations; or with one or more stations of the same kind by means of one or more reflecting satellites or other objects in space.
space station: A station located on an object which is beyond, is intended to go beyond, or has been beyond, the major portion of the Earths atmosphere. survival craft station: A mobile station in the maritime mobile service or the aeronautical mobile service intended solely for survival purposes and located on any lifeboat, life-raft or other survival equipment. mobile station: A station in the mobile service intended to be used while in motion or during halts at unspecified points. mobile earth station: An earth station in the mobile-satellite service intended to be used while in motion or during halts at unspecified points. land station: A station in the mobile service not intended to be used while in motion. land earth station: An earth station in the fixed-satellite service or, in some cases, in the mobile-satellite service, located at a specified fixed point or within a specified area on land to provide a feeder link for the mobile-satellite service. coast station: A land station in the maritime mobile service. coast earth station: An earth station in the fixed-satellite service or, in some cases, in the maritime mobile-satellite service, located at a specified fixed point on land to provide a feeder link for the maritime mobile-satellite service. ship station: A mobile station in the maritime mobile service located on board a vessel which is not permanently moored, other than a survival craft station. ship earth station: A mobile earth station in the maritime mobile-satellite service located on board ship. on-board communication station: A low-powered mobile station in the maritime mobile service intended for use for internal communications on board a ship, or between a ship
Maritime Manual
95
and its lifeboats and life-rafts during lifeboat drills or operations, or for communication within a group of vessels being towed or pushed, as well as for line handling and mooring instructions. port station: A coast station in the port operations service. emergency position-indicating radiobeacon station: A station in the mobile service the emissions of which are intended to facilitate search and rescue operations. satellite emergency position-indicating radiobeacon: An earth station in the mobilesatellite service the emissions of which are intended to facilitate search and rescue operations. space system: Any group of cooperating earth stations and/or space stations employing space radiocommunication for specific purposes. satellite system: A space system using one or more artificial earth satellites. feeder link: A radio link from an earth station at a given location to a space station, or vice versa, conveying information for a space radiocommunication service. Operational terms public correspondence: Any telecommunication which the offices and stations must, by reason of their being at the disposal of the public, accept for transmission. telegraphy: A form of telecommunication in which the transmitted information is intended to be recorded on arrival as a graphic document; the transmitted information may sometimes be presented in an alternative form or may be stored for subsequent use. telegram: Written matter intended to be transmitted by telegraphy for delivery to the addressee. This term also includes radiotelegrams unless otherwise specified. radiotelegram: A telegram, originating in or intended for a mobile station or a mobile earth station transmitted on all or part of its route over the radiocommunication channels of the mobile service or of the mobile-satellite service. radiotelex call: A telex call, originating in or intended for a mobile station or a mobile earth station, transmitted on all or part of its route over the radiocommunication channels of the mobile service or the mobile-satellite service. telephony: A form of telecommunication primarily intended for the exchange of information in the form of speech. radiotelephone call: A telephone call, originating in or intended for a mobile station or a mobile earth station, transmitted on all or part of its route over the radiocommunication channels of the mobile service or of the mobile-satellite service. simplex operation: Operating method in which transmission is made possible alternately in each direction of a telecommunication channel, for example, by means of manual control.
96
Maritime Manual
duplex operation: Operating method in which transmission is possible simultaneously in both directions of a telecommunication channel. semi-duplex operation: A method which is simplex operation at one end of the circuit and duplex operation at the other. Characteristics of emissions and radio equipment radiation: The outward flow of energy from any source in the form of radio waves. emission: Radiation produced, or the production of radiation, by a radio transmitting station. class of emission: The set of characteristics of an emission, designated by standard symbols, e.g. type of modulation of the main carrier, modulating signal, type of information to be transmitted, and also, if appropriate, any additional signal characteristics. single-sideband emission: An amplitude modulated emission with one sideband only. out-of-band emission: Emission on a frequency or frequencies immediately outside the necessary bandwidth which results from the modulation process, but excluding spurious emissions. spurious emission: Emission on a frequency or frequencies which are outside the necessary bandwidth and the level of which may be reduced without affecting the corresponding transmission of information. Spurious emissions include harmonic emissions, parasitic emissions, intermodulation products and frequency conversion products, but exclude out-of-band emissions. unwanted emissions: Consist of spurious emissions and out-of-band emissions. assigned frequency band: The frequency band within which the emission of a station is authorized; the width of the band equals the necessary bandwidth plus twice the absolute value of the frequency tolerance. Where space stations are concerned, the assigned frequency band includes twice the maximum Doppler shift that may occur in relation to any point of the Earths surface. assigned frequency: The centre of the frequency band assigned to a station. characteristic frequency: A frequency which can be easily identified and measured in a given emission. A carrier frequency may, for example, be designated as the characteristic frequency. reference frequency: A frequency having a fixed and specified position with respect to the assigned frequency. The displacement of this frequency with respect to the assigned frequency has the same absolute value and sign that the displacement of the characteristic frequency has with respect to the centre of the frequency band occupied by the emission.
Maritime Manual
97
frequency tolerance: The maximum permissible departure by the centre frequency of the frequency band occupied by an emission from the assigned frequency or, by the characteristic frequency of an emission from the reference frequency. necessary bandwidth: For a given class of emission, the width of the frequency band which is just sufficient to ensure the transmission of information at the rate and with the quality required under specified conditions. occupied bandwidth: The width of a frequency band such that, below the lower and above the upper frequency limits, the mean powers emitted are each equal to a specified percentage /2 of the total mean power of a given emission. Unless otherwise specified in an ITU-R Recommendation for the appropriate class of emission, the value of /2 should be taken as 0.5%. Frequency sharing interference: The effect of unwanted energy due to one or a combination of emissions, radiations, or inductions upon reception in a radiocommunication system, manifested by any performance degradation, misinterpretation, or loss of information which could be extracted in the absence of such unwanted energy. permissible interference: Observed or predicted interference which complies with quantitative interference and sharing criteria contained in the Radio Regulations or in ITU-R Recommendations or in special agreements as provided for in the Radio Regulations. harmful interference: Interference which endangers the functioning of a radionavigation service or of other safety services or seriously degrades, obstructs, or repeatedly interrupts a radiocommunication service operating in accordance with Radio Regulations. Technical terms relating to space satellite: A body which revolves around another body of preponderant mass and which has a motion primarily and permanently determined by the force of attraction of that other body. active satellite: A satellite carrying a station intended to transmit or retransmit radiocommunication signals. reflecting satellite: A satellite intended to reflect radiocommunication signals. geostationary satellite: A geosynchronous satellite whose circular and direct orbit lies in the plane of the Earths equator and which thus remains fixed relative to the Earth; by extension, a geosynchronous satellite which remains approximately fixed relative to the Earth. geostationary-satellite orbit: The orbit of a geosynchronous satellite whose circular and direct orbit lies in the plane of the Earths equator.
98
Maritime Manual
Maritime Manual
99
frequency conversion processes within the equipment. Requirements for spurious emissions are given in the Radio Regulations, Appendix 3. In order to avoid interference, transmitting stations should only radiate as much power as is necessary to ensure a satisfactory service, equipment should apply signal processing methods which enable the most efficient use of the radio spectrum, and every effort should be made to keep frequency tolerances and levels of unwanted emissions at the lowest levels which technology and the nature of the service permit. The performance characteristics of receivers should be adequate to ensure that they do not suffer from interference due to transmitters situated at a reasonable distance. Recommended technical characteristics for the design of equipment are given in Recommendations of the ITU-R such as: ITU-R M.489 Technical characteristics of VHF radiotelephone equipment operating in the maritime mobile service in channels spaced by 25 kHz; ITU-R M.493 Digital selective-calling system for use in the maritime mobile service; ITU-R M.1173 Technical characteristics of single-sideband transmitters used in the maritime mobile service for radiotelephony in the bands between 1 606.5 kHz (1 605 kHz Region 2) and 4 000 kHz and between 4 000 kHz and 27 500 kHz. In addition, for equipment intended for use on ships which comply with the SOLAS Convention, the IMO publishes performance standards and it is a requirement of SOLAS Chapter IV, regulation 14 that equipment conforms to these performance standards. The international standards organizations, International Electrotechnical Commission (IEC) and International Organization for Standardization (ISO), publish detailed technical equipment standards which take into account the recommendations of the ITU and the performance standards of the IMO. These can be used for the design and testing of equipment. Maritime radio equipment is generally subject to a process of type approval, whereby administrations check that equipment designs conform to the necessary standards.
100
Maritime Manual
Maritime Manual
101
Allocated to Germany (Federal Republic of) Korea (Republic of) Philippines (Republic of the) Angola (Republic of) Cape Verde (Republic of) Liberia (Republic of) Comoros (Union of the) Korea (Republic of) Spain Ireland Armenia (Republic of) Liberia (Republic of) Ukraine Iran (Islamic Republic of) Moldova (Republic of) Estonia (Republic of) Ethiopia (Federal Democratic Republic of) Belarus (Republic of) Kyrgyz Republic Tajikistan (Republic of) Turkmenistan Thailand Eritrea Palestinian Authority(1) New Zealand Cook Islands Bosnia and Herzegovina France United Kingdom of Great Britain and Northern Ireland Hungary (Republic of) Switzerland (Confederation of) Ecuador Switzerland (Confederation of) Poland (Republic of) Hungary (Republic of) Haiti (Republic of) Dominican Republic
102
Maritime Manual
Maritime Manual
103
104
Maritime Manual
Maritime Manual
105
106
Maritime Manual
Maritime Manual
107
108
Maritime Manual
Allocated to Zambia (Republic of) Kuwait (State of) Sierra Leone Malaysia Nepal (Federal Democratic Republic of ) Democratic Republic of the Congo Burundi (Republic of) Singapore (Republic of) Malaysia Rwanda (Republic of) Trinidad and Tobago
Maritime Manual
109
110
Maritime Manual
Maritime Manual
111
112
Maritime Manual
Maritime Manual
113
114
Maritime Manual
Maritime Manual
115
Allocated to France Guiana (French Department of) Guyana Paraguay (Republic of) Peru Suriname (Republic of) Uruguay (Eastern Republic of) Venezuela (Bolivarian Republic of)
In connection with the inclusion of an allocation to the Falkland Islands (Malvinas) in the Table of Maritime Identification Digits, reference is made to the declaration by the Argentine Republic reproduced as No. 49 of the Declarations and Reservations made at the end of the Additional Plenipotentiary Conference of the International Telecommunication Union (Geneva, 1992) and the declaration of the United Kingdom of Great Britain and Northern Ireland reproduced as No. 80 of the same Declarations and Reservations.
116
Maritime Manual
Maritime Manual
117 narrow-band direct-printing (telegraphy) personal computer restricted operators certificate rescue co-ordination centre radio-frequency radiotelephony search and rescue radar search and rescue transponder ship earth station short range certificate single sideband International Convention for the Safety of Life at Sea, 1974 very high frequency coordinated universal time 1 852 m
NBDP PC ROC RCC RF RT SAR SART SES SRC SSB SOLAS VHF UTC 1 nautical mile
118
Maritime Manual
Glossary
Food and Agricultural Organization (FAO) International Civil Aviation Organization (ICAO) International Labour Organization (ILO) International Maritime Organization (IMO) International Telecommunication Union (ITU) International Electrotechnical Commission (IEC) International Organization for Standardization (ISO) International Association for Marine Radio Companies (CIRM) International Hydrographic Organization (IHO) Inmarsat Global Ltd (Inmarsat) World Health Organization (WHO) World Meteorological Organization (WMO) www.fao.org www.icao.int www.ilo.org www.imo.org www.itu.int www.iec.ch www.iso.org www.cirm.org www.iho-ohi.net www.inmarsat.com www.who.int www.wmo.int
_________________
International Telecommunication Union Sales and Marketing Division Place des Nations CH-1211 Geneva 20 Switzerland [email protected] www.itu.int/publications
*36519*
Printed in Switzerland Geneva, 2011 ISBN 92-61-13701-6
Photo credits: Philip Plisson ITU/K. Bogens