Programming Basic 3

T3290, T3530, T3650

487 21 98 61.00
GB 00.25
 Contents 3

Contents:
Switching to programming mode
Adjustable parameters, change machine type
Temperature and time setting, reversing
Cooling time, residual moisture level, extra drying time
Quick view parameter list

The manufacturer reserves the right to modify design and material

specifications without notice.

487 21 98 61 - 290,530,650 - GB
 Programming 5

The programming mode is used for chang-

ing (programming) preset machine values
At the factory, the tumble-dryer has been set to specific val-
ues for:
Time, temperature, cooling, reversing, etc. These values can
be adjusted in the programming mode.
The parameters shall always match to the specific dryer
type.
The machine parameters can be changed by switching the
electronic control to Programming mode. The display will
read SP and the three push-buttons will now be used to
change the programming parameters, (see next page).

Programming is only to be carried out by qualified

personnel.

1
Switching to Programming mode
• Open the loading door (the door must be
kept open).
1 • Open the door of the control panel.

2 • Move the switch on the circuit-board to posi-

tion SP, fig. 2.
• Program the dryer as described on following
pages.
3 • End of programming. Move the switch back
to normal mode, fig. 3.

Programming mode 2
X1 1

Caution SP
7

The control circuit board in this

dryer contains hazardous volt-
6

ages. Refer servicing to qualified

personnel.
Normal mode 3
X1 1

Note !! If Programming is activated SP

when the machine power is subse-
7

quently switched on, a test and

6

diagnosis program will start.

487 21 98 61 - 290,530,650 - GB
6 Programming

Adjustable parameters:
00. Machine type
01.-03. Temperature
04. Temperature hysteresis
05. Time interval
06. Max. running time or “coin 2”
07. Running time between reversals
08. Cooling time
09.-11. Residual moisture levels
12.-14. Extra drying time

Control panel function in Programming mode

SP = Parameter Programming

Clock button:
Shift between different parameters

Count down Count up

Change of machine type

Press the clock button; the display will read 00.,
which is the first parameter (first parameter 00. =
machine type).
The parameter numbers are shown for two seconds
with a dot after the last digit.

After two seconds the machine type selected will be

displayed. Example 10 corresponds to manual time
control without reversing.

continues overleaf
487 21 98 61 - 290,530,650 - GB
 Programming 7

Change of machine type, continued

The machine type can be changed by

using the buttons to count up or down.

Count down Count up

Machine types and variants

Machine type Manual control Manual Coin Central control

of time RMC panel

Without reversing 10 50 11 / 51* 12

With reversing 30 70 31 / 71* 32

*51 and 71 are specially designed for the Japanese market.

Change of parameters
When the machine type has been select-
ed, push the clock button; parameter no.
01. will come up on the display: After two
seconds a value is shown that can be
changed by means of the count up/down
buttons.

Clock button,
change to next parameter

Now press the clock button again; the

next parameter number will come up on
the display. Count down Count up
After two seconds a value is shown that
can be changed by means of the count
up/down buttons, etc....
It is possible to scroll the parameters by
pushing the clock button repeatedly.

Note! Parameter06. = maximum running time for a manual machine or running per
coin insert on “coin insert 2” (double coin insert). If maximum running time on a man-
ual machine is changed e.g. to 30 minutes, the machine cannot choose to run more
than the maximum time, i.e. 30 minutes.

Parameters 01.-14. are on the following pages

487 21 98 61 - 290,530,650 - GB
8 Programming
Parameter no. Value Required change:
check by pressing can be set after two seconds Press the “count up/down” buttons.
the clock button

Temperature setting
The highest temperature
can be set to a value
between 32°C-85°C.
Temperature
Factory setting = 85
program High

The medium temperature

can be set to a value
between 32°C-85°C.
Temperature Factory setting = 70
program
Medium

Lowest temperature
Next para-
can be set to a value
meter
between 32°C-85°C.
Temperature- Factory setting = 50
program Low Count down Count up

Difference Can be set to a value

between between 01°C-10°C.
heat Factory setting = 02
Temperature on or off
hysteresis

Time setting
Running time Can be set to a value From 0.1 to 9.9 minutes the setting can
per pulse between 0.1 and 90 minutes. be changed by increments of
(per coin insert - Factory setting = 15 1/10 minute per push.
Time interval or push From 10 to 90 minutes the setting can
if time- be changed by increments of
controlled) 1 minute per push.

Max. running Can be set to a value From 0.1 to 9.9 minutes the setting can
time on manual between 0.1 and 90 minutes. be changed by increments of
machine or Factory setting = 60 1/10 minute per push.
Max. running running time per From 10 to 90 minutes the setting can
time or coin insert on be changed by increments of
Time inter- coin 2 (double 1 minute per push.
val, insert)
coin 2

Reversing
Can be set to a value Change the setting by
between 0.1 and 9,9 minutes. 1/10 minute per push.
Factory setting = 5.0
Running time
between reversals

487 21 98 61 - 290,530,650 - GB
 Programming 9

Parameter no. Value Required change:

check by pressing can be set after two seconds Press the “count up/down” buttons.
the clock button

Cooling time
Running time Can be set to a value
without between 00 and 10 minutes.
heat at end of Factory setting = 03
Cooling time cycle
Count down Count up

Residual moisture level

The measurement of residual moisture level consists of a combined parameter set for residual
moisture + a parameter for extra drying time.

Residual Can be set to a value The values for residual moisture are
moisture level, between 05 and F0. given in hexadecimals (05-F0). See
F0 = ready Factory setting F0 explanation on following page.
Program
to put away
P1 =
extra dry
Residual Can be set to a value
moisture level, between 05 and F0.
F0 = ready Factory setting F0
Program to put away
P2 =
ready to put away
Residual Can be set to a value
moisture level, between 05 and F0.
e.g. 30 = Factory setting 30
Program iron dry
P3 =
ironing dry

Extra drying time

Extra drying Can be set to a value Extra drying time when the value set
time between 00 and 20 minutes. in parameter 09 has been reached.
in minutes Factory setting 09
Program
P1 =
extra dry
Extra drying Can be set to a value
Extra drying time when the value set
time between 00 and 20 minutes.
in parameter 10 has been reached.
in minutes Factory setting 03
Program
P2 =
ready to put away

Extra drying Can be set to a value Extra drying time when the value set
time between 00 and 20 minutes. in parameter 11 has been reached.
in minutes Factory setting 00
Program
P3 =
ironing dry

487 21 98 61 - 290,530,650 - GB
10 Programming

Residual moisture level

Measurement principle

0% residual moisture

Ready to put away

5V F0

E0

D0

C0

B0

A0

Ironing dry
3A

30

20
Parameters 12 - 14
10 Extra drying time 0-20 minutes

0V 05

30 % 25 20 15 10 05 % 00
0 03 09 minutes

P3, P2, P1

Explanation of Y-axis (hexadecimals)

F0 The values for residual moisture are shown in the display in so-
C0
called hexadecimals - a series of numbers covering a total of 16
values for each digit (0,1,2,3,———9,A,B,C,D,E,F). A total of
B0 236 values can be shown.

A0
Example:
Total: P3, ironing dry, parameter no. 11 = 30.
236 increments
4F If the clothes are not dry enough, add increments by using the
“count up” button: 31,32,33,34,.....3A,3b,3C,3d... etc. up to F0
3F
30 = P3
2F

1F
15
05

487 21 98 61 - 290,530,650 - GB
 Programming 11

Quick-view parameter list

The following values are factory settings:

Parameter- Value/setting
number Man. Man. *Coin *CP
RMC Time Machine types.
50 10 11/51 12 W/o rev.
00. 70 30 31/71 32 W/ rev. Standard and condensate versions.

01. 85 85 85 85 Programme with high temperature.

02. 70 70 70 70 Programme with medium temperature.

03. 50 50 50 50 Low temperature

04. 02 02 02 02 Temperature hysteresis

05. 15 15 15 15 Time interval,

running time per pulse (per coin or push)

06. 60 60 60 60 Max. time or time interval for “coin 2”

07. 5,0 5,0 5,0 5,0 Running time between reversals

08. 03 03 03 03 Cooling time

09. F0 -- --* --* Moisture level: P1 (extra dry)

10. F0 -- -- -- Moisture level: P2 (ready to put away)

11. 30 -- -- -- Moisture level: P3 (ironing dry)

12. 09 -- -- -- Extra drying time: P1

13. 03 -- -- -- Extra drying time: P2

14. 00 -- -- -- Extra drying time: P3

* Payment machines: Parameters 09-14 cannot be set.

Will run without payment (bypassing the control panel)
if the machine code is set to 43

487 21 98 61 - 290,530,650 - GB