Slug Flow Analysis

Slug flow analysis
Horizontal direction Slug Flow If the liquid rate is now increased, a transition from segregated to intermittent flow occurs. The higher liquid rate causes the wave crests to touch the top of the pipe and form frothy slugs. The velocity of these liquid slugs and the alternating large gas bubbles is greater than the average liquid velocity. The large gas bubbles occupy nearly the whole pipe cross-sectional area.I.E: a) Low quality steam flow for well injection. b) Two-Phase flow systems c) Inadvertent collection in relief lines.
Occurrence:
This type of flow may occur in a pocketed line between an overhead condenser at grade and an elevated reflux drum. Discharge lines from pressure safety valves, rupture discs may have slug flow. Slug flow will not occur in a gravity flow line. Vertical Direction Slug Flow As the liquid volumetric rate decreases or the gas rate increases, the small bubbles coalesce into large bubbles which o c c u p y a m a j o r p o r t i o n o f t h e p i p e c r o s s - s e c t i o n a l a r e a . Alternating large gas bubbles and liquid slugs move through the p ipe with so me small bu bb le s o f gas e n train ed in t h e liqu id slugs. Slug flow can occur in either upward or downward vertical flow, but it is usually not initiated during downward flow. However, if slug flow is well established in an upward leg, it will persist in a su b sequ e nt d o wn ward o r ho riz on t al le g, p r o vid ed t h at ot he r conditions remain the same.
Effects of slug flow Slug flow causes serious pressure fluctuations which can upset the process conditions and cause inconsistent instrument sensing. M o r e o v e r , i t c a u s e s vibration especially at vessel inlets, pipe bends, valves and other flow restrictions. This can lead to equipment deterioration and operating problems. Special Cases of Slug flow:
Vacuum Transfer Lines. Condenser Outlet Lines. Reboiler Return Lines. Fired Heater outlets. Boiler Blowdown.
Methods to avoid slug flow By r e d u c i n g l i n e s i z e s t o a m i n i m u m p e r m i t t e d b y a v a i l a b l e p r e s s u r e differentials. By designing parallel pipe runs that will increase flow c a p a c i t y w i t h o u t increasing the overall friction loss. By using a low point effluent drain or bypass or other solutions. By arranging the pipe configurations to protect against slug f l o w . E . g . i n a pocketed line where liquid can collect, slug flow might develop. Hence pocket is to be avoided.
In Caesar II: a) The length of the fluid cylinder. (The longer the more conservative) b) The inside diameter of the pipe thru which fluid is moving. c) The estimated velocity of the fluid cylinder. (If no other value is available then taken as between 0.5 and 1.0 times the gas flow velocity.)
The slug flow time history is estimated as shown in the figure below:
Slug impact load fully developed when slug leading edge reaches this cross section.
Angle
Bend Pipe
R
Impact starts when slug edge reaches this point. Direction of slug travel
Slug rise time: R/V R: Bend Radius : Bend Angle V: Slug travelling velocity Slug impact duration: (L-R )/V Slug closing time: Slug rise time
Force
Fslug
Time R /V L-R /V R /V
Fslug=mv= (pAV)V=pAV2 P=Fluid density A=Area of pipe V=Velocity of vapor Slug impact rise and fall time=0 Slug impact duration=2L/V Slug impact Dynamic Load magnitude=rAV2
Where:
L is the estimated length of the slug cylinder V is the velocity of the slug R is the fluid density, and A is the inside area of the pipe.
The basic steps in the slug flow analysis become: a) Estimate where the maximum problems due to slug flow impact are most likely to occur. b) Compute the magnitude of the slug flow load at each of the elbows or flow restrictions of concern. c) Estimate the time waveform of the slug flow load, and use the pulse table generator to get a response spectrum for each different slug flow time waveform. d) Define the forces spectrum shock load cases. For elbows that are very close, the user may wish to apply the loads from both in the same load case. e) Run the spectrum analysis, and review the predicted displacements, forces and stresses. Not for calculating slug impact loads at bends other than 90 degree;
Outgoing direction
Incoming direction (Parallel to global axis)
Direction of slug travel
Change in momentum in coming direction = (1-)pAV2 Change in momentum perpendicular to the incoming direction = (sin )pAV 2 Direction = (sin )pAV2
This amplification is often expressed as the dynamic load factor DLF and is defined as the maximum ratio of the dynamic deflection at any time to the deflection which would have resulted from the static application of the load. For structures having essentially one degree-of-freedom and a single load application, the DLF value will range between one and two depending on the time-history of the applied load and the natural frequency of the structure.
There is no way to know for certain, so you make assumptions: - What could the smallest slug be that I would have to worry about? - What could be the largest slug that they system could handle without destroying itself? - What would be a reasonable slug, midway between the previous two?

Slug Flow Analysis

Uploaded by

Copyright:

Available Formats

Slug Flow Analysis

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Slug Flow Analysis

Uploaded by

Copyright:

Available Formats

What conditions lead to slug flow?

What are some effects of slug flow?

Slug flow analysis

Incoming direction (Parallel to global axis)

Direction of slug travel

You might also like