Washing machine error codes

Below is a list of error codes for the washer for HE and

conventional top-loading washers and front-loading washers. As
more error codes are found or published, we will add to the list. In this
Currently, the error codes for Asko, Fisher & Paykel, Frigidaire, GE are found,
Kenmore, LG, Maytag, Samsung, and Whirlpool. This list may not be complete and should
be used only as a reference.

Technical question - Click here

Calendar / Application Click on Service-Here

Ask Error Codes Washing Machine

F1 - Water supply / low water filling.

1. Check the water supply to the machine.
o2. Replace the water inlet valve.
F2 - The water level is too high.
Connected / low quality water pump.
o2. Defective water valve.
F3 - problem with the pump.
Check bomb trap and clean.
F4 - thermistor problem.
o1. Open thermistor, replace.
o2. Bad wiring in thermistor.
F5 - Failure in the thermal circuit breaker or lack of heating pause.
The selected temperature did not reach in 90 minutes.
o2. Check heating element.
o3. Check the thermostat.
F6 - engine failure.
Review the motor wiring.
o2. Replace the motor if necessary.
F7 - door lock failure in freedom.
o1. Bent pull-bar for door latch.
o2. Bad solenoid latch door.
00 - The machine had no return.
Check that the load is out of balance.
o2. Redistribute the load and the restart.

Fisher & Paykel Agua Smart Washer Error Codes

Musical series of beeps every 5 seconds and the spin speed and the rinse.
Light or intermittent - Spin is a washing load that is out of balance.
Musical series of beeps every 5 seconds and the hot temperature lights
cold, so many unrecognized water flashes in the washing machine.
Musical series of beeps every 5 seconds and the flashing light temperature
Hot - No hot water detected.
Musical series of beeps every 5 seconds and the cold light temperature flashing.
No cold water detected.
 Musical series of beeps every 5 seconds and the washing cycle flashing light of
wash and is overloaded.
Musical series of beeps every 5 seconds and rinse and spin lights - Suds
to build.
Musical series of beeps every 5 seconds and lid close failure light
intermittent - open the lid
Beeping every second of light and service (key icon) flashes of Re-set
Disconnect the washing machine, if the error returns, call technical service.

Frigidaire Front Load Washer Error Codes

E11 - Fill the time too long

E13 - Water leak in the tub or air leak in the range hood
E21 - The water is not pumping fast enough
E23 - drainage pump relay in the control panel or no cable from the
bomb
E24 - drainage pump relay on the control panel or cable not for the
bomb
E31 - Pressure sensor does not communicate with the control board
E35 - Pressure sensor indicates water fill
E36 - problem with the control board, change the control
E41 - The control panel thinks that the door switch is open
E43 - problem with the control board Replace
E44 - problem with the control board Replace
E45 - problem with the control board Replace
E46 - problem with the control board Replace
E47 - Board believes that the PTC circuit door is open in the turn
E48 - Board believes that the PTC circuit door is closed
E52 - bad signal from the tachogenerator
E56 - high motor current
E57 - High current in the motor phase
E59 - No signal from tachometer for 3 seconds
E5A - high temperature in the heat sink caused by the
overload. Replace the speed control card
E5B - high temperature on the heat sink, replace the control board
of speed
E5c - high temperature in the heat sink, replace the control board
of speed
E5D - communication problem
E5E - communication problem
E5F - communication problem
E66 - Relay failure heating element
E67 - Incorrect input voltage at the microprocessor
E68 - Ground leakage current in the heater or open fuse
E70 - The control card is not seeing the correct water supply
E71 - Wash the NTC failure. Bathtub heater Replace the control board or
of wire.
E74 - water temperature does not increase. NTC placed in the correct position
E75 - The temperature of the water in the sensor circuit
E76 - NTC for the cold water valve beyond limits. Water hoses
hot and cold switching of
E82 - control console problem. Reinsert the control board.
 E83 - control console problem. Reinstall the control board
E91 - Communication error between the user interface and dashboards
control. Check the wiring
E93 - control console issue. Reinsert the control board.
E94 - control console problem. Reinstall the control board
E95 - Communication error. Please reinsert the control board
E97 - control console problem. Reinsert the control board
E98 - control console problem. Reinsert the control board.
EB1 - input feed frequency out of limits

EB2 - input line voltage above 130 VAC. Check the

tension below 130 if the replacement control
EB3 - input line voltage below 90 VAC. Check the
control tension if it is greater than replace 90
EF1 - clogged drainage pump
EF2 - The excess of soap. advice to reduce soap
EBE - control console problem. Reinsert the control board.
EBF - control console problem. Please reinstall the control board.
EF5 - NTC for the hot water valve over the cold and the hoses
limits.Hot changed

Frigidaire Washer Error Codes (focusing on the)

first

F1 - Internal control failure - Replace the control if it does not reset.

F2 - water temperature problem - the water Check the sensor of
temperature. The readings must be more than 3K, but no more than 163K.
F3 - water level problem caused by incoming water or the pump
drainage does not work - Check the pressure switch and hose, the pump
of drainage and the blockage.
F4 - The washing machine is not progressing - the control of possible motor speed
the control panel.
F5 - keyboard problem - Replace touch pad, keyboard.
DDO - cane box switch has not been closed - Close box, check
leaf switch and the magnet.
dr - Door switch is not closed - Replace the lock assembly
from the door if the door is properly closed.

Frigidaire Front Load Washer Error Codes

1 Beep/E10--Error: The water does not enter Cause: The supply problem
water, Check twists and faucets

1 Beep/E10--Error: Water causes leaking water loose connections to seal,

the runaway from home, an excess of foam. Fix the problems.
1 Beep/E10--Error: dispenser drawer is open: The washing machine does not
it will work if the drawer is open.
 2 Beeps/E20
folded or from home. Correct.
3 Beeps/E30--Error: drum is too full. Cause: Valve seal
entry, the pressure switch or control failure. Select drainage / spinning
to remove the water. Restart.
4 Beeps/E40--Error: The door is open. Cause: The washing machine will not operate if
the door is open. Close the door.
5 Beeps/E50--Error: The engine is overheated. Cause: Wait 30 minutes
to cool down. Restart.
7 Beeps/E70--Error: Cold water does not enter. Cause: The hoses are crossed.
key problem.
15 Beeps/EF0--Error: an excess of foam. Cause: Too much detergent or
inadequate detergent for the machine.
15 Beeps/EF0--Error: The hot water is not coming in. Cause: The hoses
crusades, the problem of the key.

GE WSL Model Error Codes Washing Machine

IE - Water level error in the sensor.

Water sensor cannot send the signal for more than 5 seconds. Press
the POWER button. There are no other work buttons.
o2. Check the wiring.
o3. Check the pressure sensor switch.
o4. Check circuit board.
7E - Water, a source of error.
1. There is no 60-minute supply frequency change.
water. Press the POWER button. There are no other work buttons.
o2. Check the wiring.
Water check valve.
o4. Check the pressure sensor switch.
Check circuit board.
E - Pump drainage error.
The water level does not decrease to readjust the point within 15.
minutes to drain the washing machine water. Press the POWER button. No
there are other work buttons.
Check the wiring.
Review the pump motor.
Check circuit board.
dE - Open lid error.
1. Lid is open during the washing cycle. Close the lid.
o2. Check the wiring.
o3. Check the lid switch.
o4. Check the imbalance switch.
o5. Check circuit board.
UE - switch imbalance error.
1. Unbalanced load is detected on three occasions during a
turn operation. Open the lid.
o2. Rebalance the load of laundry and close the lid.
Check the wiring.
Check the imbalance switch.
Check circuit board.
 OE - water overflow error.
Water supply does not stop after detecting a condition
of overflow. Shut off the water supply in the home at the
washing machine and unplug the power cord.
o2. Check the wiring.
o3. Water inlet check valve.
Check the pressure sensor switch.
Check circuit board.

Front load washer error codes

E22 - filling wait time - Do not fill / fill slowly

E23 - flood protection switch for the drainage foam is
closes in idle state
E30 - the drainage pump does not have drainage issues
E31 - drainage waiting time - slow drainage
E38 - Error dispenser
E39 - Wait Time Dispenser
E42 - Motor - instantaneous current overload of the motor
E43 - DC fault - inverter failure, replace the converter card
control
E45 - The drive motor - current load overload
too heavy
E46 - Engine - temperature above, over the inverter temperature
E47 - Heat sink - Over temperature, excessive temperature of
inverter
E48 - Motor - motor phase open
E49 - The drive motor - Energy overload, the load is very heavy
E4A - Low voltage - DC bus voltage (inverter)
E4B - Turn on the software/hardware issues
E4C - More volts - DC bus (inverter)
E4E - Low voltage after the initial minimum starting voltage has not
received - The motor does not work, DC bus (inverter)
E4F - EEPROM read error failure EEProm occurs. Error no
recoverable. Reinsert the inverter control board
E52 - the main control to wake up lost communication error between the
control and the motorcycle unit

E53 - Internal buffer software error buffer error

E54 - No response from the engine, lost communication between the control and the
motor
E57 - lack of software error checking occurs - lack of
Control. Non-recoverable error. The main control card must be replaced.
E58 - Communication error - unrecoverable error. Control card
principal must be replaced
E60 - the failure of the locking switch door
E61 - open the door failure switch
E62 - contact Failure System--Heater/pump/pressure
switch
E63 - unexpected open door
 E64 - unexpected open door during execution of
E65 - Water level sensor failure
E66 - Open water temperature sensor
E67 - Water temperature sensor short
E70 - Stuck Key, continuous reading for 60 seconds
E71 - Key error Communication failure between the control and the keys

LG front-loading washing machine error codes

IE - water inlet error - No water or water fills slowly

EU - imbalance error - Load to the small ones, inclined device,
Laundry, on one hand, things are not placed distributed in the drum.
OE - drainage error--Long/Slow drainage
FE - More flow - High water level, the water does not turn off
PE - Pressure sensor error
dE - open door error
Heating - thermistor is out of service
CE - Current error oven - main assembly of the PLP is out of order, the
the coil in the stator is short-circuited
LE - Engine lock error
BE - ball sensor error
EE - EEPROM error
PF - power failure
E1 - leak error

Maytag Front Load Washer Neptune Error Codes

DO - Open Door
FL - Could not be blocked
LO - The door does not unlock
LR - motor locked rotor
ND - There is no drainage
NF - No filler
OD - Open door
Sd - Foam blocking, too much foam detected
PF - power failure

Samsung front load washer SilverCare error codes

DC - washing machine with spinning imbalance prevention

dl - The door is locked when the washing machine is running
The door is open when the washer is open
FL - Washer door does not close
H - The temperature of the water control problem (the heat problem)
control
LE - Washer tried to fill, but has not reached the water level
adequate (slow filling)
LO - The door does not unlock
E3 - The engine is not working properly
The washing machine is not draining / senses Washing machine a brief restriction,
while the drainage
nF - Washer tried to fill, but was unsuccessful
 Sr (5R) - Problem with the control
PF - Power failure, the electric service was lost while washing machine
working
OE - fault detected in the water level sensor
E2 - stuck key
BE - The engine speed sensor problem
TE - temperature sensor problem
3E - high current detected
Tension 2E--High/low detected
8E - Sensor vibration problem
7E - SilverCare control problem
SUDS - The excess foam detected during the washing cycle, the unit in
wait until the reduced foam

Whirlpool Cabrio, Kenmore Oasis, Maytag Bravos Washer error codes

LF (F30)-Long Full
LD (F32)-Long Drain
unbalanced load
OL (F70) with overload
Sd (F71)-Suds detection
lid (F81) -Open/Close lid
Post-bomb Out (open cover)
HC-heat, reversed cold
dL (F80, 82, 84, 85) - lock cover failure
dU (F83)-Unlock Fail
F1 (F68) signal pressure out of range
F2 (F2) -Keypad/User Interface Error
F40 (F40)-ATC open circuit / short circuit thermistor
F41 (F41)-RPS open/circuit thermistor
F42 (F42) - heater in unknown state
F43 (F43)-The heater is continuously on
F44 (F44) - heater cannot be turned on
F50 (F50) motor has
F51 (F51)-Motor RPS failure
F52 (F52) - The engine stop failure
F53 (F53)-Overtemperature Motor Control
F54 (F54) - Overcurrent Motor Control
F72 (F72)-Canasta Re-The lack of commitment

NOTE: The letter / number in () is what is stored in the computer's memory /

control.

Whirlpool and Kenmore Calypso Washer error codes

PF - Power supply cut

FL - The flood condition - overflow
Er - Processor error Reset
LF - Full length - Without filling
CE - Communication Error - Check the wiring, the connectors, the motor
LD - Long Drain
 CA - current average limit - 2 second average current consumption
greater than 5.55 amperes in the motor windings
Cl - instantaneous current limit - 26 ampere spike immediately in
motor windings
Balance Off
Sr - stuck relay
LS - Switch cover error

Whirlpool Duet and Kenmore model w/110 front load washing machine
Error codes - NEW

F01 - Error Eeprom

F06 - Vapor defect
F11 - Error control motor unit
F20 - The machine detects no water entering or travel of the switch.
pressure not detected
F21 - wide escape
F22 - Door lock error
F24 - Water temperature sensor error
F25 - The error drive motor of the tachometer
F26 - Door Switch Error
F27 - overflow condition
F28 - Serial communication error
F29 - Door unlock error
F30 - System error dispenser
F31 - engine control unit failure
F32 - Pressure switch failure
F34 - Download indication
F35 - Failure of the analog pressure sensor
F64 - steam valve failure entry
F66 or F00 - Vapor temperature Sensor error
F70 - the central unit for heart failure control
F71 - Heartbeat failure user interface
F74 - IU EEPROM failure
Sud - Blocking foams during the washing cycle
RL - cleaning cycle download indication
F99 - Not allowed

Whirlpool Duet and Duet HT & Kenmore model w/110 front load
frontal Washer Error Codes - MAJOR

F / H - No water detected entering the machine or a switch trip

pressure is not detected
F/02--Long drainage
Temperature F/05--Water produces error
F/06--Drive Motor tachometer error
Control F/07--Motor Unit of Error
F/09--Overflow State
F/10--Travel Control Unit (MCU) thermal heat sink
F/11--Communication serial error
F/13--Error Circuit Dispenser
F/14--EEPROM error
F/15--Control Unit (MCU) Error
Sud - SUDS LOCK (detergent overdose detected during the cycle of
washing)
F / dl - Door lock error
F / dU - Door Opening Error