Hanoi University of Science and Technology (HUST)

Faculty of Engineering Physics (FEP)

PHYSICS LABWORK
For PH1016
(New version)

Edited by Dr.-Ing. Trinh Quang Thong

Hanoi, 2024
 Experiment 1
MEASUREMENT OF BASIC LENGTH
Instruments
1. Vernier caliper;
2. Micrometer.

1. VERNIER CALIPER
1.1 Introduction

The Vernier Caliper is a precision instrument that can be used to measure internal and external
distances extremely accurately. The details of a vernier principle are shown in Fig.1. An ordinary
vernier caliper has jaws you can place around an object, and on the other side jaws made to fit inside
an object. These secondary jaws are for measuring the inside diameter of an object. Also, a stiff bar
extends from the caliper as you open it that can be used to measure depth. The accuracy which can
be achieved is proportional to the graduation of the vernier scale.

Fig.1. Structure of an ordinary vernier caliper

When the jaws are closed, the vernier zero mark coincides with the zero mark on the scale of
the rule. The vernier scale (T’) slides along the main rule (T). The main rule allows you to
determine the integer part of measured value. The sliding rule is provided with a small scale
which is divided into equal divisions. It allows you to determine the decimal part of measured
result in combination with the caliper precision (D), which is calculated as follows:
D 1 (1)
= N
Where, N is the number of divisions on vernier scale (except the 0-mark), then, for N =
10 we have D = 0.1 mm, N = 20 we have D = 0.05 mm, and N = 50 we have D = 0.02
mm.

1.2 How to use a vernier caliper

- Preparation to take the measurement, loosen the locking screw and move the slider to
check if the vernier scale works properly. Before measuring, do make sure the caliper reads
0 when fully closed.

1
 - Close the jaws lightly on the item
which you want to measure. If you are
measuring something round, be sure
the axis of the part is perpendicular to
the caliper. In other words, make sure
you are measuring the full diameter.

1.3 How to read a vernier caliper

In order to determine the
measurement result with a vernier
caliper, you can use the following
(a)
equation:
D=na+m D (2)
Where, a is the value of a division on
main rule (in millimeter), i.e., a = 1
mm, D is the vernier precision and
also corresponding to the value of a
division on sliding rule that you can
either find it on the caliper body or
determine it’s value using the eq. (1).
- Step 1: Count the number of division
(n) on the main rule – T, lying to the
left of the 0-mark on the vernier scale
– T’ (see example in Fig. 2) (b)
- Step 2: Look along the division mark
on vernier scale and the millimeter
marks on the adjacent main rule, until
you find the two that most nearly line
up. Then, count the number of divisions
(m) on the vernier scale except the 0-
mark (see example in Fig. 2).
- Step 3: Put the obtained values of n
and m into eq. (2) to calculate the
measured dimension as shown in Fig.2.
(c)
Attention: Fig.2. Method to read vernier caliper
The Vernier scale can be divided into three parts called first end part, middle part, and last
end part as illustrated in Fig. 2a, 2b, and 2c, respectively.
+ If the 0-mark on vernier scale is just adjacently behind the division n on the main rule,
the division m should be on the first end part of vernier scale (see example in Fig.2a).
+ If the 0-mark on vernier scale is in between the division n and n+1 on the main rule, the
division m should be on the middle part of vernier scale (see example in Fig.2b).
+ If the 0-mark on vernier scale is just adjacently before the division n+1 on the main rule,
the division m should be on the last end part of vernier scale (see example in Fig.2c).
II MICROMETER
2.1 Introduction
The micrometer is a device incorporating a calibrated screw used widely for precise
measurement of small distances in mechanical engineering and machining. The details of a
micrometer principle are shown in Fig.3. Each revolution of the rachet moves the spindle
face 0.5mm towards the anvil face. A longitudinal line on the frame (called referent one)
divides the main rule into two parts: top and bottom half that is graduated with alternate 0.5

2
millimeter divisions. Therefore, the main rule is also called “double one”. The thimble has
50 graduations, each being 0.01 millimeter (one-hundredth of a millimeter). It means that
the precision (D) of micrometer has the value of 0.01. Thus, the reading is given by the
number of millimeter divisions visible on the scale of the sleeve plus the particular division
on the thimble which coincides with the axial line on the sleeve.
Anvil Spindle Sleeve, Thimble – T’ Screw
face main scale - T Rachet
face

Thimble edge
Lock nut

Thimble – T’
Double
rule
Referent line
Fig.3. Structure of an ordinary micrometer

2.2 How to use a micrometer

- Start by verifying zero with the jaws closed. Turn the ratcheting knob on the end till it
clicks. If it isn't zero, adjust it.
- Carefully open jaws using the thumb screw. Place the measured object between the anvil
and spindle face, then turn ratchet knob clockwise to the close the around the specimen till
it clicks. This means that the ratchet cannot be tightened any more and the measurement
result can be read.

2.3 How to read a micrometer

In order to determine the measurement result
with a micrometer, you can also use the following
equation:
D=na+m D (3)
Where, a is the value of a division on sleeve -
double rule (in millimeter), i.e., a = 0.5 mm, D is
the micrometer’s precision and also
corresponding to the value of a division on (a)
thimble (usually D = 0.01 mm).
- Step 1: Count the number of division (n) on the
sleeve - T of both the top and down divisions of the
double rule lying to the left of the thimble edge.
- Step 2: Look at the thimble divisions mark – T’
to find the one that coincides nearly a line with
the referent one. Then, count the number of
divisions (m) on the thimble except the 0-mark (b)
- Step 3: Put the obtained values of n and m into Fig. 4. Method to read micrometer
eq. (3) to calculate the measured dimension as the
examples shown in Fig.4.
Please read carefully the following note when
performing the measurement.

3
.Attention:
The ratchet is only considered to spin
completely a revolution around the sleeve
when the 0-mark on the thimble passes the
referent line. As an example shown in Fig.5, it
seems that you can read the value of n as 6,
however, due to the 0-mark on the thimble lies
above the referent line, then this parameter is
determined as 5. Fig.5. Ratchet does not spin completely a
revolution around the sleeve, yet.
III. EXPERIMENTAL PROCEDURE

1. Use the Vernier caliper to measure

the external and internal diameter (D
and d respectively), and the height (h),
of a metal hollow cylinder (Fig.6) based
on the method of using and reading this
rule presented in part 1.2 and 1.3.
Note: do 5 trials for each parameter.
2. Use the micrometer to measure the
diameter (Db) of a small steel ball for 5
trials based on the method of using and
reading this device presented in part 2.2
and 2.3.
Fig.6. Metal hollow cylinder for measurement

IV. LAB REPORT

Your lab report should include the following issues:
1. A data sheet with one data table of the measurement results for the height ( h), external
(D) and internal (d) diameter of metal hollow cylinder, and one data table of the
measurement results for the diameter (Db) of small steel ball.
2. Calculate the volume and density of the metal hollow cylinder using the following
equations:
=p ( 2
2
).h (5)
V D -d
4
r
=

m (6)
V
3. Determine uncertainties and report the last result of those quantities in the form like
V =V ±DV
4. Calculate the volume of the steel ball using the following equation:
=1p 3 (7).
Vb Db
6
5. Determine uncertainty and report the last result of this quantity.
6. Note: Please read the instruction of “ Significant Figures” on page 6 of the document “
Theory of Uncertainty” to know the way for reporting the last result.

4
 Experiment 2

MOMENTUM AND KINETIC ENERGY IN

ELASTIC AND INELASTIC COLLISION

Equipment:
1. Aluminum demonstration track;
2. Starter system for demonstration track;
3. End holder for demonstration track
4. Light barrier (photo-gate)
5. Cart having low friction sapphire bearings;
6. Digital timers with 4 channels;
7. Trigger.

I. THEORETICAL BACKGROUND

1. Momentum and conservation of momentum

Momentum is a physics quantity defined as product of the particle's mass and velocity. It is a vector
quantity with the same direction as the particle's velocity.
R R

p =mv (1)
Then we may demonstrate the Newton's second law as
R R

SF = dp (2)
dt
The concept of momentum is particularly important in situations in which we have two or
more interacting bodies. For any system, the forces that the particles of the system exert on
each other are called internal forces. Forces exerted on any part of the system by some object
outside it are called external forces. For the system, the internal forces are cancelled due to the
Newton’s third law. Then, if the vector sum of the external forces is zero, the time rate of change of the
total momentum is zero. Hence, the total momentum of the system is constant:
R
R dp R
SF = 0 = ⇒ p = const (3)
dt
This result is called the principle of conservation of momentum.

2. Elastic and inelastic collision

2.1 Elastic collision
If the forces between the bodies are much larger than any external forces, as is the case in
most collisions, we can neglect the external forces entirely and treat the bodies as an isolated
system. The momentum of an individual object may change, but the total for the system does

5
not. Then momentum is conserved and the total momentum of the system has the same
value before and after the collision. If the forces between the bodies are also conservative,
so that no mechanical energy is lost or gained in the collision, the total kinetic energy of the
system is the same after the collision as before. Such a collision is called an elastic
collision. This case can be illustrated by an example in which two bodies undergoing a
collision on a frictionless surface as shown in Fig.1.

(a) (b) (c)

Fig. 1. Before collision (a), elastic collision (b) and after collision (c)

Remember this rule:

- In any collision in which external forces can be neglected, momentum is conserved and the total
momentum before equals the total momentum after that is
R R R R
'+ m v
m 1 v1 2
+m v 2 '= m1 (4)
2 2

v1
- In elastic collisions only, the total kinetic energy before equals the total kinetic energy
after that is
1 m v'2 + 1 m v'2 = 1 m v 2 + 1 m v 2 (5)
2 1 1
2 1 2
2 1 1
2 1 2

If the second body is in stationary (v2 = 0) then taking the vector eq. (4) along the direction from
left to right, results in
-m1v’1 + m2v’ 2 = m1v1 (6)
2.2 Inelastic collision
A collision in which the total kinetic energy after the collision is less than before the
collision is called an inelastic collision. An inelastic collision in which the colliding bodies
stick together and move as one body after the collision is often called a completely inelastic
collision. The phenomenon is represented in Fig.2.

(a) (b) (c)

Fig. 2. Before collision (a), completely inelastic collision (b) and after collision (c)

Conservation of momentum gives the relationship:

R+ R = ( + )R

m1v1 m1v2 m1 m2 v ' (7)

In the case that the second mass is initially at rest (v2 = 0) then taking the vector eq. (9)
along the direction from left to right, results in
m1v = (m1 + m2)v’ (8) Let's verify that the total kinetic energy
after this completely inelastic collision is less than before the collision. The motion is
purely along the x-axis, so the kinetic energies KE and K’ E
before and after the collision, respectively, are:
K1 m1v2 (9)
=2
1 2
1 m 2
1
K' = ( m1 +m2 )v' = ( m1 +m2 ) v (10)
2 2 m +m2
1
Then, the ratio of final to initial kinetic energy is

6
 K' = m1 (11)
K m1 m2
+
It is obviously that the kinetic energy after a completely inelastic collision is always less
than before.

II. EXPERIMENTAL PROCEDURE

2.1 Set up the measurement

In this experiment, the collisions between two carts attached with “shutter plate” (length as
100 mm) (Fig. 3a) will be investigated. One end of cart 1 is attached with a magnet with a plug
facing the starter system and the other one is attached with a plug in the direction of motion.
The duration that the carts go through the photogates before and after the collisions will be
measured by the timer (Fig. 3b) that enables to calculate the corresponding velocities.

2.2 Investigation of elastic collision

- Step 1: Place the cart 1 (m1) on the left of track closer to the starter system. The cart m2 is
stationary between the photogates. It means that its initial velocity v2 = 0. In this investigation,
cart 2 is attached with a bow-shaped fork with rubber band facing cart 1 and a needle plug
facing the end holder on the right of track (Fig. 4a). The photogate 1 should be located at
position of 50 cm and photogate 2 at 100 cm. It is also noted that in this case, the weight m1
should be haft of m2 due to cart 2 is attached with an additional weight (400 g).
- Step 2: Push the trigger on the top of vertically long stem of the starter system that enables
cart 1 to be released and accelerate in the direction to cart 2 (initially in stationary that is v2 =
0). During this process, it receives an initial velocity v1 that can be calculated by the duration t1
when it goes through the photogate 1 corresponding to the shutter plate’s length. .

(a) (b)
Fig. 3. Carts enclosed with shutter plates (a) and the timer for investigating the collision (b)

- Step 3: After collision, cart 2 moves with the velocity v’ 2 that can be calculated by the
using the duration t’ 2 measured by photogate 2 and cart 1 goes back (Fig. 4c). Record the
time t1, t’1 and t’ 2 displayed on the corresponding windows of timer as shown in Fig. 3b.
- Step 4: Repeat the measurement procedure from step 1 to 3 for more 9 times and record
all the measurement results in a data sheet 1.
- Step 5: Weight two carts to know their masses by using an electronic balance. Record the
mass of each cart on data sheet.

7
 (a)

(b)

(c )
Fig.4. Experimental procedure to investigate the elastic collision

2.3 Investigation of inelastic collision

- Step 1: Place the cart 1 (m1) on the left of track closer to the starter system. Put off the
right plug of cart 1 and attach the other one with a needle facing to cart 2 (Fig. 5a). Place
the cart 2 (m2) also stationary between the photogates as in Part 2.2. In this circumstance,
the fork plug facing cart 1 is replaced by another one having plasticine. It is noted that in
this case, the weight m1 should be twice m2. In order to get this condition, take off the
additional weight from cart 2 and put it on cart 1.

(a)

(b)

(c )
Fig.5. Experimental procedure to investigate the inelastic collision

- Step 2: Push the trigger of the starter system that enables cart 1 to be released and
accelerate in the direction to cart 2 similar previous case. Record the moving time t1 that
can be considered as t (Fig. 5b).

8
- Step 3: After collision, cart 1 sticks with cart 2 then both carts move together with the
same velocity v’ that can be calculated by the duration t’ 1 = t’ 2 = t’ measured by
photogate 2. Record the t’ displayed on the timer (Fig. 5c).
- Step 4: Repeat the measurement procedure from step 1 to 3 for more 9 times and record
all the measurement results in a data sheet 2.
- Step 5: Weight two carts to know their masses by using an electronic balance. Record the
mass of each cart.

III. LAB REPORT

Your lab report should include the following content:
1. A data sheet with the recorded values of times before and after the collision (should be
10 trials) as well as masses of two carts for both cases of elastic and inelastic collision
(with two separate data tables).
2. Check the conversation of momentum and kinetic energy before and after the collision in
the elastic collision. In this case, based on the given and measured data we have
p = L and p' = - L + m L
m m 2 ,
t2
1 1 ,
t1 t1
=1 L2 =1 L 2 +1 L
KE m and K'E m
, m
,
2 2 2 t 2
1 1 2
t t
1 1
Where L is the length of the shutter plate.
Do calculation of the uncertainties in the momentum and kinetic energy before and after
collision for each case. Make the conclusions of the obtained results.
3. Calculate the momentums and kinetic energies before and after the collision in the
inelastic collision. In this case, based on the given and measured data we have
p = L and p' = + L
m1 (m1 m2 ) t'
t
1 L 2 1 L
2

K E = m1 and K'E = (m1 + m2 )

2 t 2 t'
Where L is the length of the shutter plate.
Do calculation of the uncertainties for the momentum and kinetic energy before and after
collision for each case. Make the conclusions of the obtained results.
4. Evaluation of the percent changes in kinetic energy (KE) through the elastic and inelastic
collision (using eq. 11). Make the conclusions of the obtained results.
Note: The collision is not completely elastic because there is still some residual friction when
the carts move. That’s why the total momentum may decrease slightly by approximately 6 %
and the kinetic energy may decrease up to 25 %.
5. Note: Please read the instruction of “ Significant Figures” on page 6 of the document “
Theory of Uncertainty” to know the way for reporting the last result.

9
 Experiment 3

MOMENT OF INERTIA OF THE SYMMETRIC RIGID BODIES

I. THEORETICAL BACKGROUND

It is known that the moment of inertia of the body about the axis of rotation is determined by
I = ∫r 2 dm (1)
Where dm is the mass element and r is the distance from the mass element to the axis of
2
rotation. In the m.k.s. system of units, the units of I are kgm /s.
If the axis of rotation is chosen to be through the center of mass of the object, then the
moment of inertia about the center of mass axis is call Icm. In case of the typical symmetric and
homogenous rigid bodies, Icm.is calculated as follows
- For a long bar: I cm 1 ml 2 (2)
=
12
- For a thin disk or a solid cylinder: I cm = 1 mR 2 (3)
2
- For a hollow cylinder having very thin wall: I cm = mR 2 (4)
- For a solid sphere: I cm 2 mR 2 (5)
=
5
The parallel-axis theorem relates the moment of inertia Icm about an axis through the center of mass to the
moment of inertia I about a parallel axis through some other point. The theorem states that,
2
I = Icm + Md (6)
This implies Icm is always less than I about any other axis.
In this experiment, the moment of inertia of
a rigid body will be determined by using an
apparatus which consists of a spiral spring
(made of brass). The object whose moment of
inertia is to be measured can be mounted on
the axis of this torsion spring which tends to
restrict the rotary motion of the object and
provides a restoring torque. If the object is
rotated by an angle f, the torque acting on it
will be
tz = Dz..f (7)
where Dz. is a elastic constant of spring.
This torque will make the object oscillation.
Using the theorem of angular momentum of a
rigide body in rotary motion.
t dL = I dw = I d 2f (8)
= 2
dt dt dt Fig. 1. Experimental model to determine the
We get the typical equation of oscillation as moment of inertia of the rigid body

10
 Fig. 2. Equipments for measurment

Fig. 3. Experimental setup for measurement

of the rod
d 2f Dz (9)
dt 2 I f =
+
0
The oscillation is corresponds to a period
T = 2p I (10)
Dz
According to (10), for a known Dz, the unknown moment of inertia of an object can be found
if the period T is measured.

II. EQUIPMENT
1. Rotation axle with spiral spring having the
elastic constant, Dz = 0,044 Nm/Rad;
2. Light barrier (or photogate) with counter;
3. Rod with length of 620mm and mass of
240g;
4. Solid sphere with mass of 2290g and
diameter of 146mm;
5. Solid disk with mass of 795g and diameter
of 220mm;
6. Hollow cylinder with mass of 780g and
diameter of 89mm;
7. Supported thin disk;
8. A set of screws for mounting the objects;
9. Tripod base.

III. EXPERIMENTAL PROCEDURE

3. 1. Measurement of the rod
- Step 1: Equipment is setup corresponding
to Fig.3. A mask (width ~ 3 mm) is stuck on
the rod to ensure the rod went through the
photogate.
- Step 2: Press the button “Start” to turn on
the counter. Then, you can see the light of
LED on the photogate.
- Step 3: Push the rod to rotate with an angle
0
of 180 , then let it to oscillate freely. The
time of a vibration period of the rod will be
measured. In this case, the result you got is
averaged after several periods. Make 5 trials
and record the measurement result of period T in a data sheet.
- Step 4: Press the button “Reset” to turn the display of the counter being 0. Uninstall the rod for
next measurement.

11
3.2 Measurement of the solid disk
- Using the suitable screws to mount the solid
disk on the rotation axle of the spiral spring as
shown in Fig.4. A piece of note paper is stuck on
the disk to ensure it passing through the
photogate.
- Perform the measurement procedure similar to
that of the rod. Record the measurement result of
period T in a data sheet.
- Press the button “Reset” to turn the display of
the counter being 0. Uninstall the disk for next Fig. 4. Experimental setup for
measurement. measurement of the solid disk
3.3 Measurement of the hollow cylinder
- Using the suitable screws to mount the hollow
cylinder coupled with a supported disk below on
the rotation axle of the spiral spring as shown in
Fig.5. A piece of note paper is also stuck on the
disk to ensure the system passing through the
photogate.
- Perform the measurement procedure similar to
that of the disk. Record the measurement result of
period T (5 trials) in a data sheet.
- Push the button “Reset” to turn the display of
the counter being 0. Uninstall the hollow cylinder Fig. 5. Experimental setup for measurement
and repeat the measurment to get its rotary period of the hollow cylinder
T (5 trials) ..
- Press the button “Reset” to turn the display of t he counter being 0. Uninstall the supported disk
for next measurement.
3.4 Measurement of the Solid Sphere
- Mount the solid sphere on the rotation axle of
the spiral spring as shown in Fig.6. A piece of
note paper is also stuck on the sphere to ensure its
passing through the photogate.
0
- Push the sphere to rotate with an angle of 270 ,
then let it to oscillate freely. The obtained
vibration period of the sphere will be recorded (5
trials) in the data sheet.
- Uninstall the solid sphere and switch off the
counter to finish the measurements. Fig. 6. Experimental setup for
measurement of the solid sphere

12
III. LAB REPORT

Your lab report should include:

1. A data sheet of the vibration periods of the measured rigid bodies.
2. Determine the average value of the vibration periods of corresponding bodies and then
calculate the moment of inertia of the rod, solid disk, and solid sphere using equation (10).
3. The moment of inertia of the hollow cylinder is calculated by subtracting that of alone
supported disk from the coupled object (consisting of the cylinder and supported disk).
4. Calculate the uncertainty of the moment of inertia obtained by experiment.
5. Calculate the value of moment of inertia of the rigid bodies based on the theoretical formula (2
to 5) and compare them to the measured values. Note that you use the relatively difference as an
estimate of the errors.
6. Note: Please read the instruction of “ Significant Figures” on page 6 of the document “
Theory of Uncertainty” to know the way for reporting the last result.

13
 Experiment 4

DETERMINATION OF GRAVITATIONAL ACCELERATION USING

SIMPLE PENDULUM OSCILLATION WITH PC INTERFACE

Principle and task

Earth’s gravitational acceleration g is determined for different lengths of the pendulum by

means of the oscillating period. If the oscillating plane of the pendulum is not parallel to the
gravitational field of the earth, only one component of the gravitational force acts on the
pendulum movement.

I. BACKGROUND

As a good approximation, the pendulum

used here can be treated as a mathematical
(simple) one having mass m and a length l.
When pendulum mass m is deviated to a g
small angle g, a retracting force acts on it to l
the initial balanced position (Fig.1):
F(g) = – mg · sin g ≈ – mg. g (1) If
one ensures that the amplitudes remain
sufficiently small while experimenting, the
movement can be described by the
mg sing
following differential equation: F = mg
d 2g (2)
I = -gg Fig. 1. Pendulum with vertical oscillation plane
dt 2
The solution of eq.(2) can be written as follows:
l (3)
g = 0
sin
.t

g g

This is a harmonic oscillation having the amplitude g0 and the oscillation period T.
T = 2p . l (4)
g
If one rotates the oscillation plane Vertical
axis
around the angle q with respect to the Oscillation

plane
vertical plane as shown in Fig.2, the
components of the acceleration of gravity
g(q) which are effective in its oscillation g
plane are reduced to g(q) = g.cosq, that is q
only the force component mg.sing.cosq is mg sing.cosq
effective and the following is obtained for
the oscillation period: Mg.cosq
F = mg
T = 2p . l (5)
g cosq
Fig. 2. Pendulum with inclined oscillation plane

In this experiment you will perform the investigation of the harmonic oscillation of
mathematical pendulum in two cases to see how the gravitational acceleration depends on its
length and the inclined angle based on equation (4) and (5).

14
II. II. EXPERIMENTAL PROCEDURE

2.1 Cobra Interface

The Cobra3-Basic-Unit is an interface for measuring, controlling and regulating in physics
and technology. It can be operated with a computer using serial USB interface and suitable
software corresponding to the certain sensor. In this case it is translation/rotation recorder. All
functional and operating elements are on the front plate or on the side walls of the instrument
as can be seen in Fig. 3a. The electric connection of the movement sensor is carried out
according to Fig. 3b for the COBRA interface. The thread runs horizontally and is lead past
the larger of the two thread grooves of the movement recorder.

(a) (b)
Fig. 3. COBRA3 interface (a) and electric connections for movement recorder (b)

2.2. Pendulum with vertical oscillation plan

2.2.1. Preparation

- Set up the experiment according to Fig. 4

such that the oscillating plane runs
vertically.
- Start the MEASURE software written for
COBRA interface. The COBRA window is
appeared for setting measuring parameters
according to Fig. 5. The diameter of the
thread groove of the movement recorder is
entered into the input window d0 (12 mm are
set as a default value). In the first part of the
experiment (thread pendulum), d1 is the
double length of the pendulum in mm, that
is, the diameter of the circle described by the
centre of gravity of the pendulum. In this
case, the measured deviations of the
pendulum sphere are indicated directly in
rad. If measurements are carried out with the
g pendulum, 12 is entered for d1 (d1 = d0),
because the pendulum is now coupled 1:1
with the movement measuring unit. If the
values (50 ms) in the ”Get value every (50) Fig. 4. Experimental set-up for the
ms” dialog box are too high or too low, determination g from the oscillation period

15
noisy or non-uniform measurements can occur. In this case adjust the measurement sampling
rate appropriately. The <Start> button must then be pressed. A new measurement can be
initiated any time with the <Reset> button, the number of measurement points “n” is reset to
zero. In total, about n = 250 measurement values are recorded and then the <Stop> button is
pressed.

Fig.5. Measurement parameter box

2.2.2. Investigation for various pendulum lengths

- Step 1: Choose an arbitrary pendulum length (may be 400 mm or 500 mm). Note that the
pendulum length l was the distance of the centre of the supported mass from the centre of the
rotational axis.
- Step 2: Move the 1-g weight holder, which tenses the coupling thread between the pendulum
sphere and the movement sensor, manually downward and the release it. Set the pendulum in
motion (small oscillation amplitude) and click on the ”Start measurement” icon. After
approximately 5 oscillations click on the ”Stop mea surement” icon, a graph similar to Fig. 6
appears on the screen. Determine the duration of a period with the aid of the cursor lines,
which can be freely moved and shifted onto the adjacent maxima or minima of the oscillation
curve. Record the measurement result in a data sheet.

Fig. 6. Typical pendulum oscillation

16
- Step 3: Do the measurement for 5 times
to get the average value of the oscillation
period.
- Step 4: Repeat the measurement with
different pendulum lengths (500mm and
600mm or 600mm and 700mm).

2.3. Pendulum with inclined oscillation

plan
- Step 1: Make the arrangement of the
experimental set-up as Fig. 7. The
o
oscillation plane is initially vertical or 0 .
Let the pendulum to vibrate with its small
deflection angle. Record the duration of
one period in the second data table, then
repeat the measurement for more 4 times
at this position.
- Step 2: Rotate the vibration plane to be
o
inclined at 10 and perform the
measurement procedure similar Step 1.
- Step 3: Repeat again the measurement Fig. 7. Experimental set-up
with inclined plane corresponding q = for the variable g pendulum
020°, 40°, and 60°. Each angle is also 5
times of measurement.

III. LAB REPORT

1. Your lab report should have a data sheet with two data tables of the measurement results of
as instructed in part 2.2 and 2.3.
2. Determination of the gravitational acceleration as a function of pendulum length using eq.
(4) also show the uncertainty of this quantity correspond to each length.
3. Determination of the gravitational acceleration including its uncertainty as a function of the
inclination of the pendulum force using eq. (5) correspond to each angle..
4. Note: Please read the instruction of “ Significant Figures” on page 6 of the document “
Theory of Uncertainty” to know the way for reporting the last result.

17
 Experiment 5

INVESTIGATION OF TORSIONAL VIBRATION

Instruments: 1. Torsion apparatus;

2. Torsion rods (steel)
3. Spring balance;
4. Stop watch;
5. Sliding weight
6. Support rods and base.

Purpose of the experiment: Bars of various materials will be exciting into torsion
vibration. The relationship between the torsion and the deflection as well as the torsion
period and moment of inertia will be derived. As a result, moment of inertia of a long bar
can be determined.

I. THEORETICAL BACKGROUND
R R
If a body is regarded as a continuum and if r0 and r denote the position vector of a point
P in the undeformed and deformed states of the body, then for small displacement vectors:
R R R
u = r - r0 = (u , u 2 , u 3 ) (1)
1
R is: = ¶ui - ¶uk
and the deformation tensor e
eik
R
dxk dxi
The forces d F which act on a volume element of the body, the edges of the element being cut
R
parallel to the coordinate planes, are described by the stress tensor s :
R

sR = (2)
dF R
dA
R
Hooke’s law provides the relationship between e
modulus.
For a bar subjected to a torque as shown in Fig.1,
the angular restoring torque or torsion modulus Dt
can be determined by:
tz = Dt..j (3)
From Newton’s basic equation for rotary motion,
we have:
t dL = d ( I zw) (4)
=
dtdt
Combination eq. 3 and 4 we obtain the equation of
vibration as follows:
d 2j + Dt j = 0 (5)
dt 2 I
z
The period of this vibration is:
T = 2p I (6)
Z Fig.1: Torsion in a metal rod
D
t

The linear relationship between tz and j shown in Fig. 2 allows determining Dt. and
consequently the moment of inertia of the long rod.
18
 Fig.2: Torque and deflection of a torsion metal rod

II. EXPERIMENTAL PROCEDURE

1. Set-up experiment
The experimental set-up is arranged as shown in
Fig. 3.
- For the static determination of the torsion
modulus, the Newton spring balance acts on the
beam at a position which is corresponding to
the lever arm r. to form a right angle.
- It is recommended that a long aluminum rod,
0.5 m long, 0.002 m in diameter, should be
used for this experiment. The steel beam is also
preferable for determining the moment of
inertia of the rod with the two masses arranged
symmetrically.

2. How to perform the experiment

2.1 Determination of torque (t = Fr)
- Step 1: Assemble the steel rod on the torsion
apparatus.
Fig.3: Experimental set-up
- Step 2: Put the Newton spring balance at a
position on the beam that corresponds to the
lever arm r (maybe either 100 mm or 150 mm).
- Step 3: Pull the spring balance so that it is perpendicular to the beam to turn the disk
o o o
being deflected an angle j (10 , 20 , 30 respectively) then record the value of force F
shown on the balance’s body in the first data table.
- Step 4: Do the measurement corresponding to each angle for 5 times.

2.2 Determination of period time (T)

- Step 1: Pull out to turn the disk being deflected at angle j (you’d better to choose the
o o o
same angles as part 2.1 that is also 10 , 20 , 30 ).
19
- Step 2: Let the aluminum rod being twisted that make the hand attached to the center of
disk, vibration and use the stopwatch to count the duration of several vibrations.
- Step 3: Record the duration of 3 periods (or 5 ones) in the second data table. At each
angle, repeat the measurement for 5 times. After that, determine the time of one oscillation
period (T) for all cases.

III. LAB REPORT

You lab report should have the following main content:
1. A data sheet having two data tables for two measurements.
2. Make a graph showing the relationship of torsion on deflection angle f (in radians).
You’d better to use the computer‘s graphing software like the excel of Microsoft office.
3. Determination of the torsion modulus Dt. as the slope (m) of the graph. The slope can be
D t
either determined using the calculation m = D j or the fitting tool of the computer‘s
graphing software like the excel of Microsoft office.
Note: please read carefully the part “ Graph and Uncertainty” on page 9 of the document
“ Theory of Uncertainty” to determine the uncertainty of the torsion modul us.
4. Calculation of the moment of inertia of the long rod using the eq. (6) and its uncertainty.

20
 Experiment 6

Figure 1. Equipment for measuring

standing wave

DETERMINATION OF SOUND WAVELENGTH AND VELOCITY

USING STANDING WAVE PHENOMENON

Equipment

1. Glass tube for creating sound resonance;

2. Piston;
3. Electromotive speaker for transmitting the
sound wave and microphone for detecting the
resonant signal.
4. Function generator
5. Metal support and base-box;
6. The current amplifier with ampere-meter,
MIKE

Purpose

To understand the physical phenomenon of

standing wave and to determine the sound
wavelength and propagation velocity.
I. BACKGROUND

A standing wave, also known as a stationary

wave, is a wave that remains in a constant
position. This phenomenon can arise in a
stationary medium as a result of interference
between two waves traveling in opposite directions. The effect is a series of nodes (zero
displacement) and anti-nodes (maximum displacement) at fixed points along the
transmission line as shown in figure 2. Such a standing wave may be formed when a
wave is transmitted into one end of a transmission line and is reflected from the other
end.
In this experiment, the standing wave will be investigated by equipment shown in figure
1. Here, the sound wave is generated by the frequency generator using an electromotive
speaker. It travels along a glass tube and is reflected at the surface of a piston which can
move inside the tube. These two waves with the same frequency, wavelength and
amplitude traveling in opposite directions will interfere and produce standing wave or
stationary wave.

21
 Figure 2. Illustration of standing wave

Considering a suitable initial moment t so that the incoming wave with frequency f
making an oscillation at point N in form:
x1N = a0. sin2pft (1)
where a0 is the amplitude of the wave,
Because of N doesn’t move ( xN = 0), then the reflective wave also creates an oscillation
of which phase is opposite at N:
x2N = -a0. sin2pft (2)
It means that the algebraic sum of two oscillations is equal to 0 at N:
xN = x1N + x2N = 0 (3)
On the other hand, considering a point M which is separated from N with a distance of:
y = MN
Let the velocity of the sound wave traveling in the air is v, then the phase of incoming
wave at M will be earlier than that at N. In this case, the phase difference is denoted as:
Dt = y/v
The oscillation made by the incoming wave at M at moment t is the same as at N at
moment t + y/v.
Then, we have: x1M = a0. sin2pf(t - y/v) (4) In opposite, the oscillation made by the
reflected wave at M will be later than that at N with an amount of y/v:

X2M = -a0. sin2pf(t + y/v) (5)

Using a trigonometric identity to simplify, the resultant wave equation will be:
xM = x1M + x2M = 2a0sin2pf (y/v) . cos2pft (6)
The sound wavelength l (in meters) is related with the frequency f as the follows:
l = v/f (7)
The amplitude of the resultant wave at M is
a = ½2a0sin 2p(y/l)½ (8)
Hence:
· The positions of nodes where the amplitude equals to zero are corresponding to
2p(y/l) = kp or y = k.(l/2) (9)
where k = 0,1,2,3,…
· The positions of antinodes where the amplitude is maximum are
corresponding to
2p(y/l) = (2k+1).p/2 or y = (2k+1).(l/4) (10)
where k = 0,1,2,3,…

22
It can be seen from eq. (9) and (10) that the distance between two conjugative nodes or
antinodes is λ/2, that is:
d = yk+1 – yk = λ/2 (11)
Therefore, if the water column in the glass tube is adjusted so that the distance L between
its open-end and point N is determined as:
L = k . (λ/2) + (λ/4) where k = 0,1,2,3,… (12)
Then, there will be a nude at N and anti-nude at its open-end where the sound volume is
greatest. Equation (12) is a condition to have a phenomenon of sound resonance or
standing wave.
In this case, the sound resonance is detected by a microphone. The signal is shown by the
ampere-meter of current amplifier. Then, the phenomenon can be recorded by observing
the maximum deviation of ampere-meter’s hand corresponding to due to the position of
piston. By measuring the distance between two conjugative nodes or antinodes the sound
wavelength l (in meters) and velocity of the sound wave can be determined using eqs.
(11) and (7).

II. EXPERIMENTAL PROCEDURE

- Step 1: Switch the frequency knob on the surface of base-box to the position of 500 Hz
- Step 2: Turn slowly the crank to move up the piston and simultaneously observe the
movement of ampere-meter’s hand until it gets the maximum deviation.
- Step 3: Record the position L1 of the piston corresponding to the maximum deviation of
ampere-meter’s hand in table 1 of the report sheet.
Note: The position L1 is determined corresponding to the marked line on the piston.
- Step 4: Continue to move up the piston and observe the movement of microampere-
meter’s hand until it gets maximum position of the deviation once again.
- Step 5: Again, record the second position of the piston L2 (in millimeters) in table 1.
- Step 6: Repeat the experimental steps of 2 to 5 for more 4 times.
- Step 7: Perform again all the measurement procedures (from step 1 to step 6)
corresponding to the frequencies of 600 Hz and 700 Hz. The measurement results are
recorded in table 2 and 3, respectively.

III. LAB REPORT

Your lab report should include:
1. The data sheet having 3 data tables corresponding to frequencies of 500 Hz, 600 Hz,
and 700 Hz.
2. Calculate the wavelength and speed of sound as well as their uncertainties for each
frequency.
3. Theoretically, the speed of sound at a temperature T can be calculated as follows:
v = v0 × 1 + a .T
0 -1
where v0 = 332 m/s is the speed of sound at temperature of 0 C, and a = 1/ 273 degree
Calculate this speed (note that the value of room temperature depends on the
measurement time) then compare it to those obtained by experiment.
4. Note: Please read the instruction of “ Significant Figures” on page 6 of the document
“ Theory of Uncertainty” to know the way for reporting the last result.

23