Standalone Keypad Access Control

User Manual

Please read the manual carefully before use this unit

1.Packing List
Name Quantity Remarks
Keypad 1
User manual 1
Screw driver 1 Φ20mm×60mm,special for keypad
Rubber plug 2 Φ6mm×30mm,used for fixing
Self tapping screws 2 Φ4mm×28mm,used for fixing
Star screws 1 Φ3mm×6mm,used for fixing
Please ensure that all the above contents are correct.If any are missing please notify the
supplier of the unit.

2.Quick Reference Programming Guide

To enter the programming mode Master code #

999999 is the default factory master code

To exit from the programming mode

Note that to undertake the following programming the master user must be logged in

To change the master code 0 New code # New code #

The master code can be 6 to 8 digits

1 User ID number # PIN #

The ID number is any number between 1 & 2000.
To add a PIN user The PIN is any four digits between 0000 & 9999
with the exception of 1234 which is reserved. Users
can be added continuously without exiting programming
mode

1 Read Card #
To add a card user Cards can be added continuously without exiting
programming mode

2 User ID number # for a PIN user or

To delete a PIN or a card user 2 Read Card # for a card user
Users can be deleted continuously without exiting
programming mode

To unlock the door for a PIN user Enter the PIN then press #

To unlock the door for a card user Present the card

3.Description
The unit is single door multifunction standalone access controller or a Wiegand output keypad or
card reader. It is suitable for mounting either indoor or outdoor in harsh environments. It is housed
in a strong, sturdy and vandal proof Zinc Alloy electroplated case which is available in either a bright
silver or matt silver finish. The electronics are fully potted so the unit is waterproof and conforms to
IP68. This unit supports up to 2000 users in either a Card, 4 digit PIN, or a Card + PIN option. The
inbuilt card reader supports 125KHZ EM cards,13.56MHz Mifare cards. The unit has many extra
features including lock output current short circuit protection, Wiegand output , and a backlit keypad.
These features make the unit an ideal choice for door access not only for small shops and domestic
households but also for commercial and industrial applications such as factories,warehouses,
laboratories, banks and prisons.

4.Features
Waterproof, conforms to IP65/IP68
Strong Zinc Alloy Electroplated anti-vandal case
Full programming from the keypad
2000 uses, supports Card, PIN, Card + PIN
Can be used as a stand alone keypad
Backlight keys
Wiegand 26 input for connection to external readerWiegand 26 output for connection to a controller
Adjustable Door Output time, Alarm time, Door Open time
Very low power consumption (30mA)
Fast operating speed, <20ms with 2000 users
Lock output current short circuit protection
Easy to install and program
Built in light dependent resistor (LDR) for anti tamper
Built in buzzer
Red, Yellow and Green LEDS display the working status

5.Specifications
Operating Voltage DC12-24V
User Capacity 2000
Card Reading Distance 3-6 cm
Active Current 60mA
Idle Current 25±5 mA
Lock Output Load Max 1A
Alarm Output Load Max 20A
Operating Temperature -4560
Operating Humidity 10%- 90% RH
Waterproof Degree IP65/IP68
Adjustable Door Relay time 0 -99 seconds
Adjustable Alarm Time 0- 3 minutes
Wiegand Interface Wiegand 26 bit
Wiring Connections Electric Lock, Exit Button, External Alarm
6.Installation
Remove the back cover from the keypad using the supplied special screw driver
Drill 2 holes on the wall for the Self tapping screws and I hole for the cable
Put the supplied rubber bungs to into the two holes
Fix the back cover firmly on the wall with 2 Self tapping screws
Thread the cable through the cable hole
Attach the keypad to the back cover.

7.Wiring
Colour Function Description
Pink BELL_A Doorbell button one end
Pink BELL_B Doorbell button to the other end
Green D0 WG output D0
White D1 WG output D1
Gray ALARM Alarm negative(alarm positive connected 12 V+)
Yellow OPEN Exit button one end(the other end connected GND)

Brown D_IN Magnetic switch one end(the other end connected GND)
Red 12V+ 12V + DC Regulated Power Input
Black GND 12V - DC Regulated Power Input
Blue NO Relay normally-on end(Connect positive electric lock "-")
Purple COM Relay Public end, connect GND
Orange NC Relay Closed end(connect negative electric lock "-")
 Pink

Pink
Doorbell

DC12V
 Pink

Pink
Doorbell

DC12V
8.To Reset to Factory Default
a. Power off
b. Press and hold # key whilst powering on
c. On hearing tick twice release # key, system is back factory settings now
Registered users won’t be deleted when reset to factory default

9.Anti Tamper Alarm

The unit uses a LDR (light dependent resistor) as an anti tamper alarm. If the keypad is removed from
the cover then the tamper alarm will operate.

10.Sound and Light indication

Operate Status LED Light Color Buzzer

Standby Flash Red Slow

Keypad Short Tick Once

Operation Successful Green Long Tick Once

Operation Failed Short Tick 3 Times

Entering into Programming Red Long Tick Once

Programmable Status Orange

Exit Programming Flash Red Slow Long Tick Once

Door Opening Green Long Tick Once

Alarm Flash Red Quick Alarming

11. Detailed Programming Guide

11.1User Settings
Master code #
To enter the programming mode
999999 is the default factory master code

To exit from the programming mode

Note that to undertake the following programming the master user must be logged in
To change the master code 0 New code # New code #
The master code can be 6 to 8 digits long

Setting the working mode:

3 0 # Entry is by card only
Set valid card only users
3 1 # Entry is by card and PIN together
Set valid card and PIN users
Set valid card or PIN users 3 2 # Entry is by either card or PIN (default)

To add a user in either card or PIN mode, i.e. in the 3 2 # mode. (Default setting)

1 User ID number # PIN #

The ID number is any number between 1 & 2000. The
PIN is any four digits between 0000 & 9999 with the
To add a Pin user exception of 1234 which is reserved. Users can be
added continuously without exiting programming mode
as follows:
1 User ID no 1 # PIN # User ID no 2 # PIN #

2 User ID number #
To delete a PIN user Users can be deleted continuously without exiting
programming mode

To change the PIN of a PIN user

(This step must be done out of ID number # Old PIN # New PIN # New PIN #
programming mode)

To add a card user (Method 1) 1 Read card #

This is the fastest way to enter cards, Cards can be added continuously without exiting
user ID number auto generation programming mode

To add a card user (Method 2)

This is the alternative way to enter
1 ID number # Read card #
cards using User ID Allocation. In this
method a User ID is allocated to a card. User can be added continuously without exiting
Only one user ID can be allocated to a programming mode
single card

To add a card user (Method 3)

1 Card number #
Card number is the last 8 digits printed
on the back of the card,user ID number User can be added continuously without exiting
auto generation programming mode

To add a card user (Method 4)

1 ID number # Card number #
In this method a User ID is allocated
to a card number. Only one user ID User can be added continuously without exiting
can be allocated to the card number programming mode
To delete a card user by card. Note
users can be deleted continuously 2 Read Card #
without exiting programming mode

To delete a card user by user ID.

This option can be used when a 2 User ID #
user has lost their card

To delete a card user by card number.

2 Card number #
This option can be used when the user
Note users can be deleted continuously without
want to make the change but the card
exiting programming mode
has lost

To add a card and PIN user in card and PIN mode ( 3 1 # )

To Add a card and Pin user Add the card as for a card user
(The PIN is any four digits between Press to exit from the programming mode
0000 & 9999 with the exception of Then allocate the card a PIN as follows:
1234 which is reserved.) Read card 1234 # PIN # PIN #

To change a PIN in card and PIN mode

(Method 1) Note that this is done outside
Read Card Old PIN # New PIN # New PIN #
programming mode so the user can
undertake this themselves

To change a PIN in card and PIN mode

(Method 2) Note that this is done outside
ID number # Old PIN # New PIN # New PIN #
programming mode so the user can
undertake this themselves

To delete a Card and PIN user just delete

2 User ID #
the card

To add a card user in card mode ( 3 0 # )

The operating is the same as adding and deleting a

To Add and Delete a card user
card user in 3 2 #

To delete All users

To delete ALL users. Note that this is a

2 0000 #
dangerous option so use with care

To unlock the door

For a PIN user Enter the PIN then press #
For a card User Read card
For a card and PIN user Read card then enter PIN #

11.2Door Settings
Relay Output Delay Time

To set door relay strike time Master code # 4 0 99 #

0-99 is to set the door relay time 0-99 seconds

Door Open Detection

Door Open Too Long (DOTL) warning. When used with an optional magnetic contact or built-in
magnetic contact of the lock, if the door is opened normally, but not closed after 1 minute, the
inside buzzer will beep automatically to remind people to close the door and continue for 1 minute
before switching off automatically.
Door Forced Open warning. When used with an optional magnetic contact or built-in magnetic
contact of the lock, if the door is forced open, or if the door is opened after 20 seconds ,the inside
buzzer and alarm output will both operate. The Alarm Output time is adjustable between 0-3 minutes
with the default being 1 minute.

To disable door open detection.

6 0 #
(Factory default)

To enable door open detection 6 1 #

Alarm output time

To set the alarm output time (0-3 minutes)

5 0~3 #
Factory default is 1 minute

Keypad Lockout & Alarm Output options. If there are 10 invalid cards or 10 incorrect PIN
numbers in a 10 minute period either the keypad will lockout for 10 minutes or both the alarm and
the inside buzzer will operate for 10 minutes, depending on the option selected below.

Normal status: No keypad lockout or

7 0 # (Factory default setting)
alarm (factory default)

Keypad Lockout 7 1 #

Alarm and inside buzzer operate 7 2 #

To remove the alarm

To reset the Door Forced Open warning Read valid card or Master Code #

To reset the Door Open Too Long warning Close the door or Read valid card or Master Code #
12.The unit operating as a Wiegand Output Reader
In this mode the unit supports a Wiegand 26 bit output so the Wiegand data lines can be connected to any
controller which supports a Wiegand 26 bit input.

Pink

Pink
Doorbell

DC12V

Access Controller