WOLLEGA UNIVERSITY

COLLEGE OF ENGINEERING AND TECHNOLOGY

DEPARTMENT OF MECHANICAL ENGINEERING

POWER PLANT ENGINEERING - MEng5211

 Chapter - One
Introduction to Power Plant Engineering
 Introduction
• One only has to experience a power outage to be reminded of how
much we take electricity for granted.
• Our lighting, heating, and cooling systems no longer operate.
• Computers, televisions, videos, and other communication systems
become unusable.
• Traffic control lights become useless; elevators no longer move
people; and industries, schools, and commercial buildings become
virtually inoperable.
• We are clearly dependent on electricity for most of our everyday
activities.
• This dependence also demonstrates why electricity is regarded as one of
the most significant sociological inventions of the 20th century.
 Introduction
• A power plant is assembly of systems or subsystems to
generate electricity, i.e., power with economy and
requirements.
• The power plant itself must be useful economically
and environmental friendly to the society.
Africa at Night
A TYPICAL COAL-FIRED THERMAL POWER STATION
BOILERS
A TYPICAL COAL-FIRED THERMAL POWER STATION
 Fundamentals of Power plant
• Power plant is assembly of systems or subsystems to generate electricity, i.e,
to produce power with economy and requirements.
• So the power produced must be :
1. Economically useful
2. Environmental friendly to society
• Power plant can be defined as :
• A power plant may be defined as a machine or assembly of equipment that
generates and delivers a flow of mechanical or electrical energy.
• The main equipment for the generation of electric power is generator. When
coupling it to a prime mover runs the generator, the electricity is generated.
• The type of prime move determines, the type of power plants.
• The Steam Power Plant, Diesel Power Plant, Gas Turbine Power Plant
and Nuclear Power Plants are called THERMAL POWER PLANT,
because these convert heat into electric energy.
 Working Principle of Steam power plants
• Steam power plant is also known as Thermal power plant.
• A steam power plant converts the chemical energy of the fossil
fuels (coal, oil, gas) into mechanical / electrical energy.
• This is achieved by raising the steam in the boilers, expanding it
through the turbines and coupling the turbines to the generators
which convert mechanical energy into electrical energy as shown
in fig. 1.1.
Working Model of Stephenson's STEAM ENGINE made of GLASS
The ancient invention of the steam engine by the Hero of Alexandria
 Working principle of Steam power plants
• The following two purposes can be served by a steam
power plant:
1. To produce electric power
2. To produce steam for industrial purposes besides
producing electric power. The steam may be used
for varying purposes in the industries such as
textiles, food manufacture, paper mills,
sugar mills and refineries.
 Classification of Power Plant
• Methods of general classification of
electricity generation power plant are as
follows :
1. Status
2. Fuel type
3. Capacity
4. Prime mover
 Classification of power plant
1. Status
Classification of power plant
 Non – renewable sources:
• Most of the energy we use are from source like coal, oil, natural
gas and nuclear fuels.
• These primary energy sources are called Non – renewable sources
because once they have been used up, they cannot be replaced.
Renewable sources:
• Sources of energy that can be used over and over again are called
renewable sources. These sources can be used to produce
electricity.
• Some of the renewable sources are:
Energy from the sun (Heat and light energy)
Energy from the wind (Kinetic energy)
Energy from the waves and tides (Kinetic energy)
Energy from earth’s core (Geothermal energy)
 Classification of power plant
2. Fuel type
Thermal power plant (coal)

Internal combustion engine plants (petrol or diesel)

Gas turbine power plant (permanent gas)

Nuclear power plant (nuclear fuels)

Solar power plant (suns radiation heat)

Tidal power plant (tides in the sea)

Hydro electric power plant (potential energy of water)

Wind power (energy available in wind)

Geothermal power plant (heat energy available under the ground)

 Classification of power plant
3. Capacity
 Classification of power plant
4. Prime mover
1) Steam turbine
2) Gas turbine
3) Water turbine
4) Wind turbine
5) Combined cycle
6) Heat engine
7) other sources as wave, sun light, …etc
Classification of Power Plant

22
Classification of Power Plant Based on Prime mover
Classification of Power Plant Based on Prime mover
Classification of Power Plant Based on Prime mover
Classification of Power Plant Based on Prime mover
Classification of power plant
Classification of Power Plant Based on Prime mover
Classification of power plant

29
Classification of Power Plant Based on Prime mover
 Power Plant

• Though the main process in steam power station is the conversion

of heat energy into electrical energy, it comprises of many steps
for its proper working and good efficiency.
• The whole arrangement of a steam power station could be divided
into following steps.
Coal and ash handling arrangement
Steam generating plant
Steam turbine
Alternator
Feed water
Cooling arrangement
 Main and Auxiliary equipments
1. Coal handling plant
2. Pulverizing plant
3. Draft fans
4. Boiler
5. Ash handling plant
6. Turbine
7. Condenser
8. Cooling towers and ponds
9. Feed water heater
10. Economiser
11. Superheater and Reheater
12. Air preheater
 Power plant
• The whole arrangement is shown in a schematic figure given below.
 1. Coal and ash handling
• The coal is transported from different places to the station by
means of rails or road and is stored in a coal storage plant.
• It is to use as a preserve at the time of scarcity.
• From coal storage plant it is transferred to coal handling plant for
pulverization.
• Pulverization is the process by which large lumps of coal are
broke to small pieces .
Why Pulverization is done?
• Pulverization is done to increase the surface area of coal and thereby
helping the easy combustion of coal with small intake of air.
• The pulverized coal is fed to the boiler by means of conveyor belt.
• The coal is burnt in the boiler and the ash so produced by burning is
removed to the ash handling system and finally to the ash storage
area for its disposal.
• This process is necessary since ash in the boiler furnace does not
promote proper combustion.
 Coal handling System

Circulating water systems

Power Conversion systems

Steam Generation systems

Post-Combustion Cleanup system

 Coal handling System
• Ash is the inert matter in coal and is the residue after combustion.
• This has to be collected and disposed off without letting it out into the
atmosphere.
• A part of the ash, around 15 % collects as ‘Bottom ash’ at the
bottom of the furnace.
• The other part collects as ‘Fly ash’ in the Electrostatic
Precipitators.
• The collected ash is then transported to disposal yards or storage
silos.

36
 Coal handling System
• The percentage of ash in coal varies from 5% in good
quality coal to about 40% in poor quality coal
• Power plants generally use poor quality of coal , thus
amount of ash produced by it is pretty large
• A modern 2000MW plant produces about 5000 tons of
ash daily
• The stations use some conveyor arrangement to carry ash
to dump sites directly or for carrying and loading it to
trucks and wagons which transport it to the site of
disposal

6/1/2021 37
 Boiler
• A boiler or steam generator is a closed vessel in which

water under pressure, is converted into steam.

• It is one of the major components of a thermal power plant

• Always designed to absorb maximum amount of heat

released in the process of combustion

• Boilers are of two types-

1. Fire tube boiler

2. Water tube boiler

 Types of steam
• As shown in the diagram below, there are three types of steam:
1. Wet steam: A mixture of water plus steam (liquid plus vapor) at
the boiling point temperature of water at a given pressure.
• Quality of steam refers to the fraction or percentage of gaseous
steam in a wet steam mixture.
2. Dry steam: Steam, at the given pressure, that contains no water
(also referred to as saturated steam ).
• The steam quality = 100 %. At the top of steam generator units for
producing saturated steam, there are moisture separators used to
remove residual water droplets from outgoing steam.
3. Superheated steam: Dry steam, at the given pressure, that has
been heated to a temperature higher than the boiling point of
water at that pressure.
 Super heater
• A greater quantity of steam can be generated from a given quantity of
water by superheating it.
• The steam produced in the boiler has got moisture content so it is dried
and superheated ( i.e. steam temperature is increased above boiling point
of water)by the flue gases on the way to chimney.
• Super heating ensures two benefits at first the overall efficiency of the
system is increased and secondly the corrosion to the turbine blades
due to condensation in later stages is prevented.
• The superheated steam from super- heater is fed to steam turbine by
means of a main valve.
 Economizer
• Flue gases coming out of the boiler carry lot of heat.
• The function of economizer is to recover some of the heat from the
heat carried away in the flue gases up the flue gas stack and utilize it
for heating the feed water to the boiler.
• It is placed in the passage of flue gases in -between the exit from the
boiler and the entry to the chimney.
• The use of economizer results in saving in coal consumption , increase
in steaming rate and high boiler efficiency but needs extra investment
and increase in maintenance costs and floor area required for the plant.
This is used in all modern plants.
 Air pre-heater
• The remaining heat of flue gases is utilized by air pre-heater.
• It is a device used in steam boilers to transfer heat from the flue
gases to the combustion air before the air enters the furnace. Also
known as air heater , air -heating system.
• It is kept at a place near by where the air enters in to the boiler.
• The purpose of the air pre-heater is to recover the heat from the flue
gas from the boiler to improve boiler efficiency by burning warm air
which increases combustion efficiency, and reducing useful heat lost
from the flue.
Economizer and Air Pre-Heaters are Provided for Heat Recovery
• Boilers are provided with economizer and air pre- heaters to recover
heat from the flue gases.
• An increase of about 20% in boiler efficiency is achieved by
providing both economizer and air pre -heaters.
• If a economizer alone is provided then the efficiency will increase by
8% only.
• Most of the high capacity boilers firing coal operate with an efficiency
of around 86% on the Higher Heat Value basis.
• Loss of around 14% can be attributed to various losses of which the
dry gas loss is about 35% of the total.
• When both economizers and air pre -heaters are not provided the
boiler efficiency drops to around 66% from 86%.
• When air pre-heater is not provided the boiler efficiency will be
around 74 % only. Thus we can conserve about 20% extra fuel when
we provide both economizers and air pre-heaters in boilers
 Deaerator
• is a device that is widely used for the removal of air and other dissolved
gases from the feed-water to steam - generating boilers .
• In particular, dissolved oxygen in boiler feed-waters will cause serious
corrosion damage in steam systems by attaching to the walls of metal piping
and other metallic equipment and forming oxides (rust).
• Water also combines with any dissolved carbondioxide to form carbonic
acid that causes further corrosion.
• Most deaerators are designed to remove oxygen down to levels of 7 Parts per
billion( ppb) by weight(0. 0005cm³/L) or less.
• There are two basic types
1. the tray- type
2. the spray - type
 Flue gas stack (chimney)

• A chimney is a structure for venting hot flue gases or smoke from a

boiler, stove, furnace or fireplace to the outside atmosphere .

• Chimneys are typically vertical, or as near as possible to vertical, to

ensure that the gases flow smoothly, drawing air into the
combustion in what is known as the stack, or chimney, effect.

• The space inside a chimney is called a flue .

• Chimneys are tall to increase their draw of air for combustion and to
disperse pollutants in the flue gases over a greater area so as to reduce
the pollutant concentrations in compliance with regulatory or other
limits.
 3. Steam Turbine
• The dry and super heated steam from super -heater is fed to the
turbine by means of a main valve.
• Due to the striking or reaction impact of the steam on the blades
of turbine it starts rotating i.e. heat energy is converted to
mechanical energy.
• After giving heat energy to the turbine the steam is exhausted to a
condenser which condenses the exhausted steam by means of a
cold water circulation.
 4. Alternator
• The steam turbine is coupled to an alternator, the alternator
converts the mechanical energy into electrical energy.
• The electrical output is transferred to the bus bars through
transformer, circuit breaker and isolators.
 5. Feed Water
• The condensed water produced in the condenser is
used as feed water.
• some amount of water may be lost in the cycle but
it is compensated using an external source and the
cycle repeats and gives a better efficiency to the
system.

6/1/2021
 6. Cooling Arrangement
• In order to increase the efficiency of the plant the steam
coming from the turbine is condensed using a condenser.
• The water circulation for cooling steam in condenser is take
from a natural source like river, stream etc and the out coming
hot water from condenser is discharged in some lower portion
of the water source.
• In scarcity of water the water from the condenser is cooled and
reused with the help of a cooling tower.
Flue gas treatment systems
 Charts & diagrams
• There are quite number of charts & diagrams associated with
engineering science, all of which related in some extent to steam
tables or other related specific constants, factors, or coefficients.
• However, the most widely related to power plant engineering are
the followings:
1. T –s diagram.
2. h -s diagram.
3. T -h diagram.
4. P-h diagram
 1. T – S Diagram
• The entropy diagram for steam is often convenient because it
shows the relationship between
 Pressure
 Temperature
 Dryness Fraction
 Entropy
• With two of the factors given –
the others can be found in the
diagram. The ordinates in
the diagram represents the
Entropy and the Absolute
temperature.
 Dryness fraction of Wet Steam
• If the water content of the steam is 5% by mass, then the steam is said to be
95% dry and has a dryness fraction of 0.95.
• Dryness fraction can be expressed as:
x= ms/ ( mw+ ms)
where
• x =dryness fraction; mw= mass of water (kg); ms= mass of steam (kg)
Enthalpy of Wet Steam
• The actual enthalpy of evaporation of wet steam is the product of the dryness
fraction(x) and the specific enthalpy(hs) from the steam tables.
• Wet steam have lower usable heat energy than dry saturated steam.
ht= hsx +(1 - x) hw
where
• ht= enthalpy of wet steam (kJ/kg)
• hs= enthalpy of steam (kJ/kg)
• hw= enthalpy of saturated water or condensate (kJ/kg)
1. T – S Diagram
 2. h – s diagram “Mollier diagrams”
• The (h – s) diagram is also called the Mollier diagram or
Mollier chart, named after Dr. Richard Mollier.
• The Mollier diagram is useful when analyzing the
performance of adiabatic steady-flow processes, such as flow
in nozzles, diffusers, turbines and compressors.
2. h – s diagram “Mollier diagrams”
57
MAIN CIRCUITS/COMPONENTS FOR T.P.P

MAIN CIRCUITS :

MAIN COMPONENTS :
 SITE SELECTION OF T.P.P

 AVAILABILITY OF COAL
 AVAILABILITY OF WATER
 ASH DISPOSAL FACILITY
 LAND REQUIREMENT
 NATURE OF LAND
 LOAD CENTER
 TRANSPORT FACILITY
 AVAILIBILITY OF LABOUR
 SIZE OF PLANT
 PUBLIC PROBLEMS
 FUTURE EXPANSION
 ADVANTAGES OF T.P.P
 Fuel used is cheaper and available in large quantities.
 They respond quickly to rapidly changing load on the plant.
 Space required is less compared to hydro power plants.
 The transmission losses are less as the plant is located near the load
centre.
 A portion of steam can be used as process steam for various industries.
 The plant can take up to 20-25 % overload without any difficulty.
 Cost of electric power generation and its initial cost is less compared
with other types of power plants of same capacity.
 The unit capacity of a thermal power plant is more.
 Unskilled operators can operate the plant whereas skilled operators are
required in nuclear power plant.
 The plant can be installed at any suitable site.
 The time of installation is less compared to hydro-electric power plant.
 DISADVANTAGES OF T.P.P
 Large quantity of water is needed.
 Operation and maintenance cost is high compared to nuclear and hydro
power plant.
 Time needed for erection of plant before it is put to operation is more
compared to gas turbine and diesel power plant.
 Handling of coal and disposal of ash is difficult and it requires large
space for storage of coal.
 Pollution cause health problem to workers and habitants near the thermal
power plant.
 Starting up the plant and bringing into service takes more time.
 Flue gas emitted through thermal power plant contribute to global
warming.
 Fuel transportation cost increases if it is located away from the mines.
 The number of equipment requires more compared to others.
 Number of person requires more compared to others.
The End of
Chapter-1