H7932 3G Router

User Manual

Hongdian Corporation
F5~6, Building 14, Shangsha Science & Tech Park, Binhe Blvd., Shenzhen, China
Tel: +86-755-88864288 Fax: +86-755-83404677 Postal Code: 518048
www.hongdian.com www.mdtu.com

Copyright © 1997-2012

Release 1.0.2
Manual Declaration

Copyright

All information in this user manual is protected by copyright law. Whereby,

no organization or individual shall copy or reproduce the whole or part of this
user manual by any means without written authorization from Shenzhen
Hongdian Technologies Corporation.

Trademark

, , Hongdian, GPRS DTU, MDTU, Hongdian Technologies, Shenzhen

Hongdian and Galaxy are the trademarks and logos of Shenzhen Hongdian
Technologies Corporation. Other trademarks and logos mentioned in this
manual belong to other organizations related. Shenzhen Hongdian
Technologies Corporation does not own the rights of other trademarks and
logos.

2
H7932 3G Router User Manual

CONTENTS

CHAPTER 1 ABOUT THIS MANUAL ..............................................................4

1.1 Purpose....................................................................................................4
1.2 Applicable scope.....................................................................................4
1.3 Version information................................................................................4
1.4 Convention ..............................................................................................5
1.5 Technical support...................................................................................5
1.6 Acronym and term .................................................................................6
CHAPTER 2 Product Introduction ..................................................................9
2.1 Galaxy 3G overview ..................................................................................9
2.1.1 Product appearance ........................................................................9
2.1.2 Other Accessories..........................................................................11
2.1.3 Device installation .........................................................................11
2.2 Function and features.............................................................................12
2.2.1 Hardware function.........................................................................13
2.2.2 Software function ..........................................................................13
2.3 System application ..................................................................................13
CHAPTER 3 ROUTER CONFIGURATION .....................................................15
3.1 Overview...................................................................................................15
3.2 Connection settings.................................................................................15
3.2.1 Environment requirements ..........................................................15
3.2.2 Connection method.......................................................................16
3.2.3 Network configuration ..................................................................18
3.2.4 System login...................................................................................22
3.3 WEB-based configuration.......................................................................23
3.3.1 General .......................................................................... 23
3.3.2 Network ......................................................................... 25
3.3.3 Applications ....................................................................................31
3.3.5 Forward...........................................................................................44
3.3.6 Security ...........................................................................................46
3.3.7 System ............................................................................................49
3.3.8 Status ..............................................................................................54
CHAPTER 4 FREQUENTLY ASKED QUESTIONS (FAQ)................................56
4.1 Fault analysis ...........................................................................................56
APPENDIX: SOFTWARE UPGRADE DESCRIPTION......................................58
H7932 3G Router User Manual

Chapter 1 About This Manual

This chapter briefly describes the function and role the this user manual has had,
and gives the readers the information on how to read this user manual as the
®
best guideline while Hongdian H7932 series products are installed and
operated.

1. Purpose
2. Applicable scope
3. version information
4. Convention
5. Technical support
6. Acronyms and terms

1.1 Purpose
This user manual is developed mainly on the basis of H7932 V1.0, and is used
®
as the guideline while Hongdian H7932 series products are installed and
tested.

1.2 Applicable scope

This user manual is applicable to those who have certain knowledge and skills
on the computer communication network, electronic technology, and network
device management and other relevant personnel that need to use Hongdian®
H7932 Router.

Applicable product version: H7932 V1.0 version

1.3 Version information

®
Hongdian H7932 Router may be adjusted functionally and updated
technically from time to time according to the needs of the market and users.
Meanwhile, the developers may not find out the incorrect content in this user
manual in time due to various reasons. The above cases may cause change of
the version of this user manual. The table below records the version
information and revision reason of this user manual in different periods for the
reader’s reference.

Table -1.1: Revision History

Version Revised by Involved dept. Revised on Description

V1.0.0 Caradoc Liu 2010-2-23 Beta

V1.0.1 Caradoc Liu 2010-3-17 Release

V1.0.2 Bobby 2012-7-10 Beta

H7932 3G Router User Manual

1.4 Convention
For reading and using this user manual fast and conveniently, the following
conventions are reached for some abbreviations, icons, notes, security
warnings and tips that appear in this user manual:

Table -1.2: Convention Table

Item Description Note

®
H7932 Means Hongdian H7932 3G Appears in the process after
Router series products Chapter 2

®
H7000 Means Hongdian Wireless Appears in the process after
DDN Communication System Chapter 2
series products
Means tips or experiences Appears in the installation and
that can save time in the testing process in this user manual
installation and testing
process

Prompts the users or relevant Appears in the use and operation

readers to remember some process in the this user manual
important information or
parameters descriptions

Warning: e.g. improper Generally appears in the product

temperature, unstable introduction and installation
voltage etc. description process in this user
manual

Caution: informs the users of Appears in the description process

the invalid or improper beyond Chapter 1 in user manual
operation in the operation
and testing process.

1.5 Technical support

To help the users fast resolve the problem occurring in their operation process
and obtain the correct solution of the problems on the hardware, operating
system, installation and testing, we are available anytime in the following
manner:

Call service:

Tel (sales) +86-755-88864288

Technical support: +86-755-88864298
24Hours hotline +86-13316996093
+86-13672886484
Fax +86-755-83404677
Post code 518048

5
H7932 3G Router User Manual

E-mail service:

Technical support: [email protected]

Service [email protected]

 Website and BBS service:

Website: www.hongdian.com
BBS: http://www.mdtu.com/forum/default.asp

1.6 Acronym and term

In this user manual, the following acronyms and terms are used:

APN Access Point Name

APP Application
ATM Asynchronous Transfer Mode
ATM Auto Table Machine
AuC Authentication Centre
BG Border Gateway
BGP Border Gateway Protocol
BSC Base Station Controller
BSCC Base Station Control Connection
BSS Base Station System
BSSGP BSS GPRS Protocol
BTS Base Transceiver System
CDMA Code Division Multiple Access
CDR Call Detail Record
CGF Charging Gateway Function
CSD Circuit Switch Data
DDN Digital Data Network
DDP DTU DSC Protocol
DHCP Dynamic Host Configuration Protocol
DNS Domain Name System
DSC Data Service Center
DTU Data Terminal Unit
EGP External/Exterior Gateway Protocol
EIGRP External/Exterior Internet Group Routing Protocol
EMC Electro Magnetic Compatibility
ESP Electro Static Precautions

6
H7932 3G Router User Manual

ETSI European Telecommunications Standards Institute

GGSN Gateway GPRS Support Node
GMSC Gateway MSC
GPRS General Packet Radio Service
GSM Global System for Mobile Communications
GSN GPRS Support Node
GTP GPRS Tunneling Protocol
GTP-id GTP Identity
HLR Home Location Register
HSCSD High Speed Circuit Switch Data
IGMP Internet Group Management Protocol
IGRP Internet Gateway Routing Protocol
IN Intelligent Network
IP Internet Protocol
IPv4 IP version 4
IPv6 IP version 6
IPSEC IP Secure Protocol
ISDN Integrated Services Digital Network
ISP Internet Service Provider
L2TP Layer 2 Tunneling Protocol
LA Location Area
LLC Logical Link Control
MAP Mobile Application Part
MDNS Mobile Domain Name System
MDTU Mobile Data Terminal Unit
MIB Management Information Base
MS Mobile Station
MSC Mobile Switching Center
MT Mobile Terminal
MTBF Mean Time Between Failure
MTTR Mean Time To Recovery
N/A Not Applicable
NAS Network Access Server
NAT Network Address Translation
NTP Network Time Protocol
O&M Operations & Maintenance
PAP Password Authentication Protocol

7
H7932 3G Router User Manual

PCF Packet Control Function

PDP Packet Data Protocol
PDN Packet Data Network
PDSN Packet Data Service Node
PLMN Public Land Mobile Network
POS Point of Sales
PTM-G Point-to-Multipoint Group Call
PTM-M Point-to-Multipoint Multicast
QoS Quality of Service
RA Routing Area
RADIUS Remote Authentication Dial In User Service
RIP Routing Information Protocol
RSC Register Service Center
RTOS Real Time Operating System
RTP Real-time Transport Protocol
RTU Remote Terminal Unit
RSVP Resource reSerVation Protocol
SCADA Supervisory Control and Data Acquisition
SGSN Serving GPRS Support Node
SIM Subscriber Identify Module
SMS Short Message Service
SMSC Short Message Service Center
SNMP Simple Network Management Protocol
STK SIM Tool Kits
TCP Transmission Control Protocol
TDMA Time Division Multiple Access
TMN Telecommunication Managed Network
UDP User Datagram Protocol
UIM User Identify Module
UMTS Universal Mobile Telecommunication System
USSD Unstructured Supplementary Service Data
UTK UIM Tool Kits
VLR Visitor Location Register
WAN Wide Area Network
WAP Wireless Application Protocol
WDDN Wireless Digital Data Network

8
H7932 3G Router User Manual

CHAPTER 2 Product Introduction

2.1 Galaxy 3G overview

Combining with the third generation of mobile communication technology and WLAN
technology, Galaxy 3G mobile network data communication terminal product is
designed as a high-tech 3G product upon the needs of users. It can provide data
communication service for these users at any time and in any place.

Galaxy H7932 3G Router is characterized with excellent transmission reliability and a

wide range of applicability. It is the ideal choice for various sectors as a special data
communication system.

2.1.1 Product appearance

The appearance, installation position and dimension of the router are shown below. In
consideration of different application sites, the installation accessories are provided on
both sides. You can put it on table directly without using these accessories; while in
industry, finance, public utilities and other related application sites, it is generally
required to fix it with the installation accessories to comply with the industrial
application requirements.
H7932 3G Router User Manual

LED TWO SIM card slots

Fig. 2.1.1-1: Front Panel

The indicators on the front panel are described as the table below:
Indicator State Description
PWR： Power supply indicator, light, solid: normal

RUN： Router status, blink slowly: works normal

LAN1～5—LINK： LAN1～LAN5 status, blink when data communication
LAN1～5—ACT： LAN1 ～ LAN5 connect status: light, solid: connection
normal. Otherwise dark
NET： Dark (no connection, no dial-up); blink fast(during
dial-up), blink slowly(connect 2.5G network); light,
solid:(connect 3G network)
RF： Module power indicator, light, solid: normal

Back panel interface

Galaxy H7932 3G Router’s all interfaces are designed on the back panel as shown
below:

GPS LAN COM DEF DC ANT

GPS antenna available on GPS edition only

Fig. 2.1.1-2: Back Panel

The interfaces on the back panel are described as below:

10
H7932 3G Router User Manual

ANT：Antenna (SMA negative terminal) interface, which is able to match with standard
short antenna, vehicular antenna or directional antenna;

DEF：Reset button used for restoring the default parameters.

DC：DC power supply interface. (Be sure to check if the voltage of power supply is
consistent with the label on the router)

LAN：10/100BaseT self-adapting Ethernet interface;

COM：DTU function, this port receives data from a RS232 port, and sends all the data
it received to an IP address or a domain on the Internet. All these are automatically and
based on mobile network and data will be sends transparently without any change.

2.1.2 Other Accessories

For safe transportation purpose, Galaxy H7932 3G Router should be packaged properly.
Pease keep the packaging materials well after the package is opened for future use in
case of re-transportation.

Standard fittings
ƒ Galaxy H7932 3G device 1 (packaged upon the order conditions)
ƒ 3G antenna 1
ƒ +12V power adapter 1
ƒ User manual 1 (CD-ROM)
ƒ Certificate of conformity and warranty card 1
ƒ Mounting and securing fittings 1 pair

Optional accessories
ƒ 1.5m RJ45 cable 1

Check the amount of articles after open-package. For the specific amount, please refer
to the user order contact.

2.1.3 Device installation

Note: Please don’t install Galaxy H7932 3G Router while it is powered.

2.1.3.1 Environment requirements

The system can be used under the following conditions:
ƒ Voltage : +5VDC~26VDC
ƒ Power Consumption:
ƒ Peak working Current: 240mA@+12VDC
ƒ In time of idling: 40mA@+12VDC
ƒ Operating Ambient Temperature: -20~+60ºC
ƒ Storage Temperature: -30~+70ºC
ƒ Relative Humidity: <95% (no condensation)

11
H7932 3G Router User Manual

Galaxy H7932 3G Router can be placed in office, on wall or installed or fixed in any
places, without special wiring and heat radiating requirements.

To ensure the long-term and stable operation of system, grounding measures and
dust-proof measures should be taken on power supply, keep ventilation and a proper
room temperature.

Caution:

1. This system cannot be used under severe condition, such as acid/alkali

environment, strong magnetic field etc. In such environments, the normal
operation of this system cannot be ensured. Any physical damage will not be
included in the quality guarantee;
2. This product is a Class-A information product, which may cause radio interference
in living environment when being used. In this case, the users are required to take
some proper measures.

2.1.3.2 Wiring
RJ-45 - Ethernet interface
Standard 10/100BaseT Ethernet switch port, self-adaptive
DC - power supply interface, Galaxy H7932 3G router’s power supply is generally
+12VDC
ANT - antenna interface
The standard 5OΩ/SMA RF connector (female) is applied. In the environment of some
industrial applications, the lightning protection measures should be taken. You can
install the lightning protection device between this connector and antenna.

Note:

1. Keep this product away from any heating source;

2. Don’t place this product in dusty or humid environment;
3. Keep it away from some possible interference sources such as metal wall,
microwave oven etc;
4. To ensure that Wi-Fi network signal is received well, please pay attention to the
position and the angle of antenna. Don’t place antenna inside the shielded metal
case.

2.2 Function and features

Galaxy series 3G mobile data communication terminal product features platform and
modularization design. Upon the different demand from the users, the platform
extension, modem combination and clipping are carried out to comply with various
application demands of different clients. Combination of Broadcom hardware platform
with Linux-based GOS (Galaxy Operation System) software platform is its core
advantage.

The features of full-function Galaxy 3G mobile data communication terminal product

include:

12
H7932 3G Router User Manual

2.2.1 Hardware function

z SYSTEM, NET, LAN indicators

z Factory default configuration restoration button

z Antenna interface: 50Ω/SMA negative end

z Serial data interface (DB9): RS-232(DCE)

z Serial data interface rate: 300 to 230,400 bits/s

z Ethernet interface: one 10/100BaseT/RJ45 self-adapting

z Configuration interface: WEB/Telnet or RS-232

2.2.2 Software function

ƒ Supporting HSUPA/HSDPA/EDGE/GPRS or EVDO/CDMA 1x

ƒ Built-in DHCP Service

ƒ Supporting DMZ host computer

ƒ Supporting DDNS

ƒ Supporting static routing list

ƒ Supporting IP address and port filtration

ƒ Supporting monitor mobile network traffic quality.

ƒ WEB/Telnet Management

ƒ Local Firmware Upgrading/ Configuration Backup

ƒ System Log Server

2.3 System application

Multiple application modes for H7932 3G Router are described as follows:

z Application Mode One: Application in video monitoring

The center-to-multipoint network generally needs to be adopted for the

application mode of video monitoring. Please connect and install the router
and network camera according to the following schematic diagram.
Furthermore, other Ethernet interface equipment can be also connected at
the video monitoring site for built-in Ethernet exchangers:

13
H7932 3G Router User Manual

Diagram 2.3-1: Schematic diagram for video application

z Application Mode Two: Application in SoHo

There is one built-in 10M/100M self-adapting fast Ethernet port within

H7932 3G Router, which greatly facilitates SoHo user getting access to the
internet.

Diagram 2.3-2: Schematic diagram for application in SOHO

z Application Mode Three: Application in banking business

14
H7932 3G Router User Manual

H7932 3G Router is able to be connected to the target machine and other

network devices at the same time. Take ATM network in the banking
business for example. ATM machine needs to be connected to the host
computer of bank, and at the same time, it is also connected to the video
camera, and thereby monitoring the conditions around ATM machine.

Diagram 2.3-3: Schematic diagram for application in banking business

Chapter 3 Router Configuration

3.1 Overview
Galaxy H7932 3G Router features built-in WEB interface configuration, management
and debugging tools. Before using Galaxy H7932 3G Router, users should configure
relate parameters; during using, you can freely change related parameters and perform
software upgrade and simple test etc.

When you enter Galaxy H7932 3G Router built-in WEB configuration interface, you can
set and manage its parameters as described below.

3.2 Connection settings

3.2.1 Environment requirements
When you want to use Galaxy H7932 3G Router, a computer and a UIM/SIM card should
be prepared according to the following requirements:

15
H7932 3G Router User Manual

ƒ Computer with Ethernet card and TCP/IP protocol

1. IE6.0 or higher
2. Support 1024x768 resolution display

3.2.2 Connection method

For your convenient use, we recommend you plug your SIM/UIM card into H7932’s card slot
before your configuration. Then power on H7932 and begin your configuration. Upon the
actual conditions, connect and configure Galaxy H7932 3G Router by the following two
methods:

Note:

You can configure H7932without any card, but you may not connect to the internet until you insert
a SIM/UIM card.

Warning:

Never pull or plug your SIM/UIM card when H7932 is power on. Your card may be damaged.

Warning:

The metal casing of H7932 3G Router has to be well connected to the ground so as to ensure the
router a safe, stable and reliable operation.

3.2.2.1 Ethernet direct connection method

Using Ethernet cable with RJ-45 connector, directly connect the computer to one of LAN
ports on Galaxy H7932 3G Router as shown in the figure below:

Fig. 3.2.2.1: Wiring Method 1

Note: Galaxy H7932 3G Router’s LAN port is designed with self-adaptive cross connect
technology, so the straight-through cable or cross cable can be both applied to connect
devices for communication.

16
H7932 3G Router User Manual

3.2.2.2 LAN connection method

When it is required to connect Galaxy H7932 3G Router to local network through HUB
or switch, connect the hub or switch out-link port with any one of its switch ports as
shown in the figure below.

Fig. 3.2.2.2: Wiring Method 2

3.2.2.3 Serial port connect

ƒ COM – serial interface

COM serial communication interface is a standard RS-232(DCE) interface

with DB9 terminal (negative terminal). It can be used for the configured
console (CONSOLE) or normal communication interface.

The cables of RS-232(DCE) interface are defined as follows:

DB-9 connector (DCE-negative terminal)

PIN Name Description Direction Remark
of signal s
1 CD Carrier Detect --Æ
2 RXD Received Data Å--
3 TXD Transmitted Data --Æ
4 DTR Data Terminal Ready Å--
5 GND Signal Ground
6 DSR Data Set Ready --Æ
7 RTS Request To Send Å--
8 CTS Clear To Send --Æ
9 RI Ring Indicator --Æ

ƒ RJ-45 – Ethernet Interface

Self-adapting (Version 2.0 or above) standard 10/100BaseT Ethernet

switching interface

17
 H7932 3G Router User Manual

ƒ ANT – antenna interface

The standard 5OΩ/SMA radio-frequency connector (negative terminal) is

adopted for use. In addition, the lightning-proof measures need to be
adopted for some operating conditions, so you may place a lightning
protection device between the connector and the antenna.

Attention:

1. The products shall be far away from any heating device;


2. Don’t place the products in the dusty or wet environment;
3. The products shall be far away from some potential interference sources, like the metal wall, and
micro-wave oven, etc;
4. Pay attention to the position and angle of antenna to ensure it works well. Don’t place the
antenna in the shielding metal box.

3.2.3 Network configuration

After the configuration environment is connected well as one of the connection
methods, the local configuration computer IP address and other parameters should be
set. Take the LAN connection method as an example to describe the network
configuration procedure shown as below.

1. Configuration computer setting

First, enter the computer control panel of the selected computer, find “Network
Connections” icon and double click it to enter, select “Local Area Connection”
corresponding to the network card on this page. Refer to the figure below.

Fig. 3.2.3-1: Computer Local Connection Configuration

Enter (double click or right click) the “Local Area Connection”Æ“Property (R)” and enter
the interface shown in the figure below:

18
H7932 3G Router User Manual

Fig. 3.2.3-2: Computer Local Connection Configuration

Select the “Internet Protocol (TCP/IP)”, click the “Properties”, and enter the interface as
below:

19
H7932 3G Router User Manual

Fig. 3.2.3-3: TCP/IP Properties Configuration

Method 1: general configuration

This method will temporarily interrupts the communication between the computer
under configuration and LAN, and the specific parameter configuration is shown as
below:

IP address: 192.168.8.* (*indicates any integral between 2 to 254)

Subnet mask: 255.255.255.0
Default gateway: 192.168.8.1

Remember:
Galaxy H7932 3G Router LAN port factory default parameter:
IP address: 192.168.8.1;
Subnet mask: 255.255.255.0
Galaxy H7932 3G Router factory default login parameter:
Management interface login IP address: 192.168.8.1
Login name: admin
Login password: admin

Method 2: advanced configuration

If you don’t want to interrupt local PC LAN communication and configure Galaxy H7932
3G Router when the former network configuration exists, it is required add route (IP).

20
H7932 3G Router User Manual

The configuration operation is shown as below:

Click the “Advanced (V)…”button in Fig. 3.2-5 to enter the interface as below:

Fig. 3.2.3-4: Advanced TCP/IP Properties Configuration

Click the “Add (A)”button under the “IP address (R)”, and fill in the IP address that you
want to add:

Fig. 3.2.3-5: Add TCP/IP Address

After the configuration is completed, click the “Add”. By now the computer has a route
to Galaxy H7932.

21
H7932 3G Router User Manual

Note:

As shown in Fig. 3.2-3, “Default gateway” depends on whether the configuration

computer connects with Internet through original local network configuration. If
Internet is accessed through original local network, the default gateway setting does
not need to be modified; if Galaxy H7932 3G Router + is used, you need to modify the
default gateway and configure it as Galaxy H7932 3G Router’s default LAN IP address
192.168.8.1.

2. Network check

„ Step 1: IP configuration check

Use the command of ipconfig to check whether the IP address is correctly set or added.
You can enter DOS mode and key-in command: ipconfig, for instance:

C:\>ipconfig

Windows IP Configuration

Ethernet adapter local connection:

Connection-specific DNS Suffix. :

Auto configuration IP Address . . .: 192.168.8.7
Subnet Mask . . . . . . . . . . .: 255.255.255.0
Default Gateway . . . . . . . . . : 192.168.8.1

„ Step 2: connectivity check

After the configuration is completed, you can check the connectivity between it and
Galaxy H7932 3G Router by ping command. Key-in ping command in system command
line:

Ping 192.168.8.1

If the following information appears:

Pinging 192.168.8.1 with 32 bytes of data:

Reply from 192.168.8.1: bytes=32 time=2ms TTL=64
Reply from 192.168.8.1: bytes=32 time=2ms TTL=64

By now, it means that the configuration computer has been connected to the router. You
can carry out configuration operation on it.

3.2.4 System login

Open the IE browser, and input http://192.168.8.1/ in address bar, as shown below:

Fig. 3.2.4-1: Web Login

22
H7932 3G Router User Manual

And then you can enter user login identity authentication interface as shown below:

Fig. 3.2.4-2: User Login Verification

User should use default user name and password when log in for the first time:

ƒ User name: admin

ƒ Password: admin

Input correct user name and password, and enter the WEB configuration interface.

3.3 WEB-based configuration

Galaxy H7932 3G Routers can be configured in WEB mode. The WEB-based operation
features visualization and simplicity, so it is recommended to perform parameter
configuration and operation in WEB mode. Connect the PC and Galaxy router according
to the description in the previous section. Start up IE (6.0 or higher) browser on your
PC to carry out the configuration.

3.3.1 General

23
H7932 3G Router User Manual

Drawing 3.3.1-1: System Configuration Window

You can select the function and display the configuration window for the
function after clicking on the related option on the top left corner of
configuration window. Please see the following drawing:

Menu Descriptions

Drawing 3.3.1-2: Main Option Bar

The options on the main option bar are as follows:

z Network
z Applications
z VPN
z Forward
z Security
z System
z Status

Move the mouse pointer onto any option, and click on it to display the
related sub-options or configuration window. The functions about each
sub-option and configuration window will be in detail described in the
following sections.

The functions of the most common buttons are as follow:

ƒ 【Save】: used to save the current configuration;

ƒ 【Cancel】: used for canceling the current configuration without saving;
ƒ 【Refresh】: used for refreshing the messages on the window;
ƒ 【Return】: used for returning to last window;

24
H7932 3G Router User Manual

3.3.2 Network
When you click the “Internet” tab, the following sub-tabs appear on the page:
„ LAN
„ Modem
„ Parameter Select
„ Connection Type
„ DHCP Sever

Fig. 3.3.2: Internet Configuration Tab

3.3.2.1 LAN

In the “Local Network” main tab, click the “LAN” sub-tab to set the LAN port and enter
the following configuration interface:

Fig. 3.3.3.1: LAN Configuration

In this interface, you can set the host name, local IP address and its subnet mask:

【Host Name】: Set the router’s host name.

【Local IP Address/Subnet Mask】: Set the local IP address and subnet mask. The LAN
port supports to configure four LAN IP address.

3.3.2.2 Modem

In the “Internet” main tab, click the “Mobile Network (Embedded Modem)” sub-tab to
set the modem parameters and go to the following configuration interface:

25
H7932 3G Router User Manual

Fig. 3.3.2.1-1: Modem

【Mod】: Modify the current settings.

【Del】: Delete current settings.
【En】: Enable/disable current settings.
【Add】: Add SIM ID.

【Auto-Dialup】: Set the account number of 3G network service provided by ISP.

【Interface Name】: Set the SIM card name.
【APN】: Set the APN of the internet access service provided by ISP.
【Service Code】: Set the name of 3G network service provided by ISP.
【User Name】: Set the account number of 3G network service provided by ISP.
【Password】: Set the password of account number of 3G network service provided by
ISP.
【Network Type】: DEFAULT means router will obey default option to choose network;
AUTO means router will choose available network automatically; Other options mean
router will use certain network only.
【Advanced setting】: Configure advanced parameter by dialing protocol.

26
H7932 3G Router User Manual

Note:

This feature is special. It’s used to match with Parameter Select feature together. For
example, if need to communicate with two different data servers via VPN tunnel.
There is a priority for two VPN tunnel. So each tunnel need to bind one SIM ID.

In the “Advanced setting” tab, it contains “PPP Advanced Settings” & “Internet
Connection Type Settings”, the interface of “PPP Advanced Settings” is as below:

27
H7932 3G Router User Manual

Fig. 3.3.2.1-2: PPP Advanced Settings

Considering the difference of mobile network authorization, the Point to Point Protocol
connection should be compatible with different network. Advanced setting is used for
the PPP special setting. Click “PPP Advanced Setting” button to start settings.

Normally, it is not required to change the setting for most of networks and
applications. If it is necessary, you need to be cautious in setting PPP Advanced based
on the network environment. For detailed configuration, consult the local mobile
operator and carry out multiple trials to achieve the best suitability.
【CHAP, PAP, MS-CHAP, MS-CHAPv2】are negotiation protocol types while PPP dialing.
【Compression Control Protocol negotiation】: Set whether disable Compression Control
Protocol negotiation. 0: disable; 1: enable.
【Address/Control compression】: Set whether disable Address /Control compression.
【Protocol field compression negotiation】: Set whether disable protocol field
compression negotiation
【VJ style TCP/IP header compress】: Set whether disable Van Jacobson style TCP/IP
header compress.
【Connection-ID compression】: Set whether disable the connection-ID compression
option in VJ.
【Debug】: Set whether enable the debug log function.
【Use Peer's DNS】: Set whether disable Use Peer's DNS.
【LCP Echo Interval】: Set LCP’s maximum interval time, in second.
【LCP Echo Failure】: Set LCP’s maximum request times.
【MTU】: Set the number of bytes of the maximum transfer unit.
【MRU】: Set the number of bytes of the maximum receive unit.
【local IP】: Set the local IP address.
【Remote IP】: Set the remote terminal’s IP address.
【Other Options】: Users can define their own options here.

3.3.2.3 Parameter Select

28
H7932 3G Router User Manual

Fig. 3.3.2.3: Parameter Select Interface

Fig. 3.3.2.3-1: Parameter Select Interface

【Status】Enable/disable the parameter select feature.

【Rule Name】Set the rule ID from 0 to 9. 0 is the prepreerence.
【Interval】: Set the check interval.
【Retry Times】: Set the check times.
【Running Timeout】: Set the active time for current rule. Once the time is over, it will
switch to the next rule.
【Interface Name】: Select the interface name for check.
【Check method】: Select the check mode for state or ICMP. State mode means router
will automatically check the specified interface as the interval and retry times. Once the
status is failed, router will automatically switch rule from current rule.

29
H7932 3G Router User Manual

ICMP mode means router will automatically check the specified destination IP as the
interval and retry times. Once the ICMP is failed, router will automatically switch rule
from current rule.

3.3.2.4 Connection Type

In the “Internet” main tab, click the “Internet Connection Type” sub-tab to set the
internet connection type. Select the internet connection type from the “Connection
Type” drop-down menu: “Modem” and “Custom”. Below, we will describe the
configuration in different modes:

Fig. 3.3.2.4: Modem configuration Interface

【Work Mode】: Default mode for gateway. It also supports route mode.
【Default Route】: Select interface name as the default route.
【DNS Type】: Specify interface or customize DNS.
【Interface Name】: If specify interface for DNS type, need to select interface name.

3.3.2.5 DHCP server

In the “Local Network” main tab, click the “DHCP Server” sub-tab to set the DHCP
server parameters and go to the following configuration interface:

30
H7932 3G Router User Manual

Fig. 3.3.2.5: DHCP Configuration Interface

The configuration parameters include:

【DHCP Server】: Set whether enable the DHCP server function: Enable/Disable.
【IP Pool】: Set the range of the DHCP dynamic address pool as the default bro
interface or customize the IP address range.
【Gateway Type】: Set the gateway to client assigned by DHCP: Default, Static, as same
as router’s gateway.
【DNS Type】: Specify interface or customize DNS.
【Lease Time】: Set the lease time, namely the time that the client uses the assigned IP
【Add】: Map the DHCP client’s MAC address with IP.

3.3.3 Applications
When you click the “Applications” tab, the following sub-tabs appear on the page:
„ DDNS
„ Timing Operation
„ Trigger On-line Data
„ ICMP Check
„ DTU
„ Interface Check

31
H7932 3G Router User Manual

Fig. 3.3.3: Applications Configuration Tab

3.3.3.1 ICMP Check

In the “Applications” main tab, click the “ICMP Check” sub-tab to set the ICMP Check
parameters and go to the following configuration interface:

Fig. 3.3.3.1: ICMP Check Interface

Trigger On-line Data parameters include:

【Destination IP or Domain】: Set whether enable the ICMP Check Service IP and
domain name.
【Retry Times】: Set how many times ICMP pack will be send.
【Normal Interval】: Set the interval of ICMP packs.
【Source Type】: Set ICMP package’s source IP address.
【Failed Interval】: Set how many seconds ICMP check will fail if no response.

3.3.3.2 Interface Check

In the “Applications” main tab, click the “Interface Check” sub-tab to set the interface
parameters and go to the following configuration interface:

32
H7932 3G Router User Manual

Fig. 3.3.3.2: Interface Check

【Interface Name】: Set which interface will be check.

【Flow Direction】: the way to check data flow.
【Check Interval】: Set the interval of check.
【Retry Times】: Set the check times.

3.3.3.3 DDNS

The router is designed with DDNS (Dynamic Domain System) function which can make
others to search the dynamic IP address by internet domain.

In the “Application” main tab, click the “DDNS” sub-tab to set DDNS parameters and go
to the following configuration interface:

33
H7932 3G Router User Manual

Fig. 3.3.3.3: DDNS Configuration Interface

DDNS configuration parameters include:

【DDNS Server】: Set whether enable DDNS service function: Enable/Disable.

【Service Provider】: Select the DDNS service provider that router currently supports.
Domestic DDNS service provider: 88IP (www.88ip.net), 3322 (www.3322.org); oversea
DDNS service provider: DNSEXIT (www.dnsexit.com), ZONEEDIT (www.zoneedti.com),
CHANGEIP (www.changeip.com), Dyndns (members.dyndns.org); you can also
select”custom” and choose your own DDNS service provider if it is not listed above.
【Server Port】: Set the port number of the DDNS server provided by the service
provider. The default port number is 80.
【User Name】: Set the legal user name of the DDNS service registered in the service
provider.
【Password】: Set the password of the legal user name of the DDNS service registered
in the service provider.
【User Domain】: Set the domain of the DDNS service provided by the service provider.
【Update Interval】: Set the interval of the DDNS client obtains new IP, in second.

3.3.3.4 DTU

In the “Applications” main tab, click the “RTU” sub-tab to set the DTU parameters and
go to the following configuration interface:

34
H7932 3G Router User Manual

Fig. 3.3.3.4: DTU Interface

DTU parameters include:

【DTU Service】: Set whether enable the DTU Service.

【Work Mode】: Work as a Server or a Client. Client will register to server automatically.
【Local Port】: Set the receive port if work mode is server.
【Protocol:】: Select the protocol used to transmit.
【Received Packet Max Length】: Set the max length of received packet, this value must
smaller than 1024.
【Received Timeout】: Set the timeout for receiving data.
【RS232 Data Timeout】: Set the timeout for RS232 data.
【Rs232 Setting】: Set parameters of Rs232 port, please set these according to your
device’s Rs232 port parameters.

3.3.3.5 SNMP

In the “Applications” main tab, click the “SNMP” sub-tab to set the Timing Operation
parameters and go to the following configuration interface:

35
H7932 3G Router User Manual

Fig. 3.3.3.5 SNMP

【SNMP Sevice】: Set whether enable the DTU Service.

【Port】: Set the SNMP port.
【Community】: Set the SNMP community.

3.3.3.6 M2M

In the “Applications” main tab, click the “M2M” sub-tab to set the Timing Operation
parameters and go to the following configuration interface:

Fig. 3.3.3.6 M2M

36
H7932 3G Router User Manual

【M2M Sevice】: Set whether enable the M2M Service.

【Server IP or Domain】: Set the server IP or domian.
【Server Port】: Set the server port.
【Login Times】: Set login max times.
【Heartbeat Interval】: Set the heartbeat interval for M2M connection.
【Retry Times】: Set the SNMP community.
【Task Failure Time】: Set the SNMP community.

3.3.3.7 Timing

In the “Applications” main tab, click the “Timing” sub-tab to set the Timing Operation
parameters and go to the following configuration interface:

Fig. 3.3.3.7: Time Interface

The configuration parameters include:

【Add】: Add the Timing Operation operated at certain time.
【Status】: Set whether enable the Timing Operation.
【Task Name】:Set the task name for timing operation.
【Task Type】: Select the task type like reboot, dialup and dialdown.
【Set Time】: We have five types of time: Clock, day, and week. All you need processing
the time is to fill each type with valid value. When setting, for each type of time, you
need to split the different value with ",", and you can use "xx-xx" to represent a period
of time.

37
H7932 3G Router User Manual

3.3.3.8 Wake Up

In the “Applications” main tab, click the “Wake Up” sub-tab to set the Trigger On-line
Data parameters and go to the following configuration interface:

Fig. 3.3.3.8: Wake Up Interface

Wake Up parameters include:

【Wake Up Service】: Set whether enable the Wake Up.

【Wake Up Method】: Set wake up method via phone&data or phone.
【Offline Method】: Set the offline method for timeout or idle.
【Online Time】: Set the online time.
【Phone Number】: Set the phone number of wakeup.
【Task Type】: Set wakeup task type for dialup, dialdown or reboot.

3.3.4 VPN
When you click the “VPN” tab, the following sub-tabs appear on the page:

38
H7932 3G Router User Manual

Fig. 3.3.4: VPN Interface

When you click the “VPN” tab, the following sub-tabs appear on the page:
„ VPDN
„ Tunnel
„ IPSec

3.3.4.1 VPDN
Click the “Add” tab; the following sub-tabs appear on the page:

Fig. 3.3.4.1-1: VPDN Interface

39
H7932 3G Router User Manual

Fig. 3.3.4.1-2: VPDN Interface

【VPDN Service】: Enable/disable the VPDN Service.

【Interface Name】: Set the VPDN name.
【Protocol】: Select the VPN protocol for PPTP or L2TP.
【Server IP or Domain】: Set the VPN server IP or domain name.
【Username】: Set the username.
【Password】: Set the password.
【Advanced Settings】: Set the advanced setting like CCP and so on.

3.3.4.2 Tunnel

Click the “Add” tab; the following sub-tabs appear on the page:

Fig. 3.3.4.2-1: Tunnel Interface

40
H7932 3G Router User Manual

Fig. 3.3.4.2-2: Tunnel Interface

【IP Tunnel Service】: Enable/disable the tunnel service.

【Tunnel Name】: Set the tunnel name.
【Tunnel Mode】: Select tunnel mode for ipip or GRE
【Local Virtual IP】: Set the local virtual IP of tunnel.
【Interface Type】: Select interface type of tunnel for interface or static IP.
【Local Extern Interface】: Select the local extern interface.
【Peer Extern IP】: Set the peer extern IP.

3.3.4.3 IPsec

41
H7932 3G Router User Manual

Fig. 3.3.4.3-1: IPsec Interface

Click the “Add” tab; the following sub-tabs appear on the page:

Fig. 3.3.4.3-2: IPsec Interface

【Select】: Select the IPSec phase 1.

【Policy Name】: Set the policy name in IPSec phase 1.
【Initial Mode】: Select IPsec mode for main mode or aggressive mode.
【Encrypt】: Select IPSec encryption arithmetic.
【Hash】: Select IPSec Hash arithmetic.
【Authentication】: Select IPSec authentication mode for pre-share key.
【Pre Share Key】: Set the pre-share key.
【Match Identify】: Set the match Identify.
【IKE Lifetime】: Set the IKE lifetime.
【Group Name】: Select the group for group 1024 or group 1536.
【DPD Service】: Enable/disable DPD service.
【DPD Delay】: Set the DPD delay time.
【DPD Timeout】:Set the DPD timeout.

42
H7932 3G Router User Manual

Fig. 3.3.4.3-3: IPsec Interface

【Select】: Select the IPSec phase 2.

【Policy Name】: Set the policy name in IPSec phase 1.
【Encryption Protocol】: Select
【Encrypt】: Select IPSec encryption arithmetic.
【Hash】: Select IPSec Hash arithmetic.
【PFS】: Enable/disable PFS.
【Lifetime】: Set the lifetime in phase 2.
【Transport Mode】: Select transport mode for transport mode, tunnel mode or auto
negotiation.
【Local Subnet】: Set the local subnet.
【Remote Subnet】: Set the remote subnet.

43
H7932 3G Router User Manual

Fig. 3.3.4.3-4: IPsec Interface

【Select】: Select the IPsec setting.

【Interface Name】: Set the IPSec name.
【Match Phase 1】: Select IPSec policy name for phase 1.
【Match Phase 2】: Select IPSec policy name for phase 1.
【Destination IP or Domain】: Set the peer IP or domain name.
【Encrypt Interface】: Select the encryption interface.

3.3.5 Forward
When you click the “Forward” tab, the following sub-tabs appear on the page:
„ NAT & DMZ
„ Static Route

Fig. 3.3.5: Forward Tab

3.3.5.1 Nat

In the “Forward” main tab, click the “NAT” sub-tab to set the route mode, NAT and DMZ
functions and go to the following configuration interface:

44
H7932 3G Router User Manual

Fig. 3.3.5.1-1: NAT Interface

Select the “NAT” option to go to the following configuration interface:

Fig. 3.3.5.1-2: NAT Interface

【Select】: Select NAT or MASQ.

【Chain】: Select the NAT mode.
【Protocol】: Select the protocol for NAT mode.
【Source Address】: Set the source IP address.
【Replace Address】: Set the replace IP address.

3.3.5.2 Static Route

In the “Forward” main tab, click the “Static Route” sub-tab to set the static route
parameters and go to the following configuration interface:

45
H7932 3G Router User Manual

Fig. 3.3.5.2-1: Static Route Configuration Interface

To add the static route, click the “Add” button and go to the following configuration
interface:

Fig. 3.3.5.2-2: Static Route Configuration Interface

【IP Address/Mask】: Configure the destination network address and mask of this static
route.
【Gateway Type】: Select gateway name for interface or static IP address.
【Gateway】: Select gateway interface or set the gateway static IP address

3.3.6 Security
When you click the “Security” tab, the following sub-tabs appear on the page:

„ IP Filter
„ Domain Filter
„ MAC Filter

3.3.6.1 IP Filter
Click the “Add” to go to the following configuration interface:

46
H7932 3G Router User Manual

Fig. 3.3.6.1-1: IP Filter Interface

You can choose filter type here: IP filter rules for Basic or Expand
Select the “Basic” to go to the following configuration interface:

Fig. 3.3.6.1-2: IP Filter Interface

The configuration parameters include:

【Type】: Basic type is based on IP address filter. Expand type is based on IP address
and port filter.
【ID】: Set the identification of the filter rule, the ID is available from 2000 to 2699.
【Default Action】: Accept means permit the added IP address and port. Drop means
deny the added IP address and port. Generally, we need to add the rule for deny at
first.
【Protocol】: Select the protocol for filter rule.
【Source Type】: Custom means you might specify the source IP or IP segment for
permit or deny. Any means all IP addresses are permitted or denied as you configured.
Host means the only IP address is permitted or denied.
【Source IP】: Set the source IP address of the filter rule, may be defined IP address or
one IP segment. Specially, you must configure the initial IP of IP segment.

47
H7932 3G Router User Manual

【Wildcard Bits】: Configure the wildcard for source IP address or IP segments.

【Destination IP】: Set the source IP address of the filter rule, may be defined IP
address or one IP segment. Specially, you must configure the initial IP of IP segment.
【Wildcard Bits】: Configure the wildcard for source IP address or IP segments.

3.3.6.2 Domain Filter

Fig. 3.3.6.2: Domain Filter Interface

【Domain Keyword】: Set the domain keyword, e.g. www.google.com.

3.3.6.3 MAC Filter

Fig. 3.3.6.3: MAC Filter Interface

Click the “Add” to go to the following configuration interface:

48
H7932 3G Router User Manual

Fig. 3.3.6.3-1: MAC Filter Interface

【MAC】: Set the the MAC address.

【Default Action】: Select the action mode for accept or drop.
【Filter Mode】: Select the filter mode for input, forward or both.

3.3.7 System
When you click the “System Tools” tab, the following sub-tabs appear on the page:

„ Local Log
„ Remote Log
„ Clock
„ Account
„ Network Test
„ Files

Fig. 3.3.7: System Tab

3.3.7.1 Local Log

In the “System Tools” main tab, click the “Local Log” sub-tab to view the log
information and go to the following configuration interface:

49
H7932 3G Router User Manual

Fig. 3.3.7.1: Log View Interface

Log view settings include:

【Local Log】: Set the type of log to be displayed.

After selecting the log type, you can make the following operations:

【View】: Display log in the Log Table.

【Clear】: Clear the log in the Log Table.
【Export】: Export the logs file.

Log display:

【Log Table】: Display the system log information in the table.

3.3.7.2 Remote Log

In the “System” main tab, click the “Remote Log” sub-tab to set the log function and go
to the following configuration interface:

50
H7932 3G Router User Manual

Fig. 3.3.7.2: System Log Management Interface

The system log configuration parameters include:

【Local Log Status】: Set whether enable local log function: Enable/Disable.
【Remote IP or Domain】: Set the IP address/domain name of the remote server,
generally the IP address of the PC that receives the log information.
【Remote Port】: Set the port number of the remote server.

Note:

For the success of remote log receive, the remote log server must be started.

3.3.8.3 System clock

In the “System Tools” main tab, click the “Clock” sub-tab to set the system’s clock
function. Time Synch. Type option is the method to synchronize the system time: NTP
and Manual.

Select the Manual to set the time manually.

Select the NTP to go to the following configuration interface:

51
H7932 3G Router User Manual

Fig. 3.3.8.3: Clock Configuration Interface

The system clock configuration parameters include:

【Status】: Enable/disable the Clock service

【NTP Server IP or Domain】: Set the domain or IP address of the NTP server.
【NTP Sever Backup】: Set the backup NTP server IP address/domain.
【NTP Synch. Interval】: Set the interval of the router making NTP synchronization in
successive two times.
【Time Zone】: Set the time zone.

3.3.8.4 Account

The router provides the user with the power to modify the password, In the “System”
main tab, click the “Account” sub-tab to set the account management function and go
to the following configuration interface:

52
H7932 3G Router User Manual

Fig. 3.3.7.4: Account Interface

The system clock configuration parameters include:

【Account Type】: Set the account based on Web.

【Account Level】:Set the account authority. Admin authority can configure all features.
Guest authority just can view all feature.

3.3.7.5 Network Test

In the “System” main tab, click the “Network Test” sub-tab.

Fig. 3.3.7.4: Account Interface

【Destination】: Set the destination IP address for ping or trace testing.

【Ping】:Select the ping testing for the destination IP address.
【Trace】: Select the trace testing for the destination IP address.

3.3.7.5 File

In the “System” main tab, click the “File” sub-tab to upgrade and backup function.

53
H7932 3G Router User Manual

Fig. 3.3.7.5: System Reboot Interface

【Firmware Setting】:Upgrade firmware/patch .

【Backup Setting】:Import/export the configuration.
【Save】: Save the current configuration as default.
【Load】: Default the current configuration to default.
【View】: Check the current patch name in the router.
【Delete】:Delete the selected patch.

3.3.8 Status
When you click the “Status” tab, the following sub-tabs appear on the page:

„ Base Information
„ LAN
„ Modem
„ Routing Table

Fig. 3.3.8: Status Tab

Tab description:

【Base Information】: Display the system information.

54
H7932 3G Router User Manual

【LAN】: Display LAN port’s running information.

【Embedded Modem】: Display USB wireless network’s running information.
【Route Table】: Display the route table information.
【DHCP Client】: Display the DHCP Client information.

55
H7932 3G Router User Manual

Chapter 4 Frequently Asked Questions (FAQ)

4.1 Fault analysis
Fault 1: All indicators are off.

Check whether the cables are connected correctly. Meanwhile, check whether the
power supply complies with the requirements. Galaxy H7932 3G Router’s label
indicates the detailed requirements regarding the power supply voltage. Check whether
the power supply voltage is identical with that specified in the label.

If the input voltage is correct, but all indicators are off, maybe the device fails. Please
contact your sales representative.

Fault 2: Unstable phenomenon appears after working for a long time.

Check whether the device is overheated. If it is overheated, put the device in a

ventilated place.

Fault 3: The device doesn’t execute self-checking.

Make sure the power supply is correct.

Fault 4: How to resolve the problem if the following information appears when you ping
the router?

Pinging 192.168.8.1 with 32 bytes of data:

Request timed out.

Such information indicates that error occurs in the installation process. You must check
the followings in sequence:
9 Whether PC is connected with Galaxy H7932 3G Router correctly by
Ethernet cable?
(Note: H7932 Router’s LINK indicator and PC’s Link indicator must be on).
9 Whether PC’s TCP/IP environment is configured correctly?
(Note: If H7932 Router’s IP address is 192.168.8.1, PC’s IP address must be
192.168.8.xxx).

For more check, click the relevant menu and enter the DOS interface. Type the
command: ipconfig, and press the Enter key, for example:
H7932 3G Router User Manual

C:\>ipconfig

Windows IP Configuration

Ethernet adapter local connection:

Connection-specific DNS Suffix. . . . :

IP Address . . . . . . . . . . . . . . . . . . . : 192.168.8.48
Subnet Mask . . . . . . . . . . . . . . . . . : 255.255.255.0
IP Address . . . . . . . . . . . . . . . . . . : 192.168.0.48
Subnet Mask . . . . . . . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . . . . . . : 192.168.0.254

(Type the command: ipconfig? to get more operation help regarding ipconfig
command).
H7932 3G Router User Manual

Appendix: Software Upgrade Description

Upgrade tool description and operating instructions

Galaxy H7932 3G Router is designed with the platform technology, whose software can
be upgraded with the development of the communication and network technology.

WEB upgrade:

Galaxy H7932 3G Router supports the function of upgrading the firmware directly by
importing the upgrade file via the WEB configuration interface. Log in the WEB
configuration page by means of entering the router’s IP address (LAN port or WAN
port) in the browser’s address bar. Click System Tools -> Firmware Upgrade, to go to
the Web firmware upgrade interface. Click the Browse key to find the corresponding
upgrade file. Click the Save button to upgrade the firmware.

In the process of upgrade, don’t make any other operation to the Web configuration
page. Otherwise, the upgrade may fail, which may make the router fails. After the
upgrade, this Web page will prompt that the upgrade succeeds or fails. If upgrade fails,
you can repeat the above operations again to upgrade the firmware.

Note:
1. In the software upgrade process never cut off the power supply or disconnect the
communication between the PC and the router.

58