Scribd
Upload
5 views3 pages

Problem Set 1 - DC Circuits - Part - 1

This document is a problem set for an Introduction to Physical Electronics course at Ain Shams University, focusing on DC circuits. It includes various problems related to circuit analysis, such as finding equivalent resistance, applying Kirchhoff's laws, and using node-voltage and mesh-current methods. The problems require students to analyze circuits, calculate currents and voltages, and determine power in different configurations.

Uploaded by

ahmedashrafaliibrahim
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
5 views3 pages

Problem Set 1 - DC Circuits - Part - 1

This document is a problem set for an Introduction to Physical Electronics course at Ain Shams University, focusing on DC circuits. It includes various problems related to circuit analysis, such as finding equivalent resistance, applying Kirchhoff's laws, and using node-voltage and mesh-current methods. The problems require students to analyze circuits, calculate currents and voltages, and determine power in different configurations.

Uploaded by

ahmedashrafaliibrahim
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

AIN SHAMS UNIVERSITY

Faculty of Engineering
Computer and Artificial Intelligence Program
(CAIE)
Introduction to Physical Electronics Spring 2025
PHM123

Problem Set 1: DC Circuits – Part #1

Problems
1- For the circuit shown in the figure,
a) State the number of
i. nodes,
ii. major nodes,
iii. meshes.
Label them clearly on the circuit

b) Name
i. 2 branches
ii. 2 loops that are NOT meshes.

2- Find the equivalent resistance as seen by the


source.

3- Using KCL and KVL, 𝟐Ω


a) Find 𝑖𝑥 in the next circuit + 𝒗𝒐 −
and the voltage 𝑣𝑜 .
b) Find the total power 𝒊𝒙 𝟔Ω 𝟐𝒊𝒙
𝟒𝟓 𝑨
supplied in the circuit.

1
4- Using KCL and KVL,
a) Find 𝑖𝑥 in the next circuit.
b) Find the power delivered
by the dependent source in
the circuit in the circuit. 𝒊𝒙 𝟏𝟓𝟎𝒊𝒙

5- The variable resistor R in the circuit in


the figure is adjusted until 𝑖𝑜 equals 𝑹
10 𝑚𝐴. Find the value of R

𝒊𝒐

6- Find 𝑣1 and 𝑣𝑔 in the circuit


shown 𝑣𝑜 in the figure 𝒊𝟐
when equals 5 V.
𝒊𝟏 + +

𝒗𝒈 𝒗𝟏 𝒗𝒐

− −

7-
a) Use the node-voltage
method to find 𝑣𝑜 for the + +
circuit shown in the figure.
b) Find the total power 𝒗∆ 𝒗𝒐
supplied in the circuit.
− −

8- Use the node-voltage method to


a) Find 𝑣1 and 𝑣2 in the circuit 8Ω
shown in the figure. + +
b) Prove that the delivered 𝒗𝟏 40 Ω 𝒗𝟐 120
𝟔𝑨 80 𝟏𝑨
power is equal to the Ω
dissipated power in this − − Ω
circuit.

2
9-
a) Use the node-voltage method to
find the branch currents 𝑖1 , 𝑖2 and
𝑖3 in the circuit shown in the
figure.
b) Check your solution by showing
that the power dissipated in the
circuit equals the power
developed.

10- Use the mesh-current method to find the


power dissipated in the resistor 15Ω in + 𝒗𝒙 −
the circuit shown in the figure.
𝟑𝒗𝒙

11- Use the mesh-analysis method to find the value of


𝑣𝑜 in the circuit shown. − 𝒗𝒙 +

You might also like