1.

ND72360 far driver

Controller model: ND72360

Phase/Line current: 360A/170A
Exterior: S24
Operating Voltag: 48/60/72
Highest voltage(V): 88
Adapted Motor Power (kW): 2-3
Speed: 100
Physical Dimension (MM): 189*121*65.5

Features:
The ND series Hall one-line pass-through controller is a high-end high-power permanent magnet
synchronous motor controller with the advantages of high quality, high efficiency, and intelligence. It
is suitable for vehicle applications of various Hall motors. It is suitable for middle and high speed
motorcycles with in-wheel motors, mid-mounted motors, and high-end electric tricycles.

Rich software parameter configuration：

* Monitor and configure the controller through the visual computer interface, and update and
upgrade online.
* The current at different speeds can be adjusted online.
* The maximum speed of forward and backward, economic speed can be set.
* The overall bus current and phase current can be set.
* The accelerator pedal threshold can be set to adjust the response sensitivity of the pedal.
Perfect protection function：
Monitor working voltage, current, temperature, motor, gear, accelerator pedal, brake, etc. Ensure the
safety of vehicle driving control

2. KLS7230S
General functions:
(1)Extended fault detection and protection. The LED flashing pattern indicates the fault
sources.Customers can read the error code in PC software or Android Tablet also.
(2)Monitoring battery voltage. It will stop driving if the battery voltage is too high and it will
progressively cut back motor drive power as battery voltage drops until it cuts out altogether at the
preset "Low Battery Voltage" setting.
(3)Built-in current loop and over current protection.
(4)Configurable motor temperature protection range.
(5)Current cutback at low temperature and high temperature to protect battery and controller. The
current begins to ramp down at 90℃ case temperature, shutting down at 100℃.
(6)The controller keeps monitoring battery recharging voltage during regen braking.
(7)Maximum reverse speed and forward speed can be configured between 20% and 100%
respectively and separately.
(8)A 4pin connector to RS232 port and a Z-TEK USB to RS232 cable allows for configuration,
programming and software upgrades using the tablet which must be based on Android OS
now.People can do the same things on PC software by using a standard USB to RS232 cable instead.
(9)Provision of a +5 volt and +12 volt output to supply various kinds of hall sensors.
(10)5 switch inputs which are activated by connection to 12V. Default to throttle switch, brake
switch,reversing switch,forward switch and Boost switch.
(11)2 analog 0-5V inputs that default to throttle input, and motor temperature input
(12)Copy signal of one of hall sensors.
(13)Configurable boost switch. Enables the maximum output power achievable if the switch is turned
on.
(14)12V brake switch input used different port from motor temperature sensor.You can use both
brake switch and motor temperature sensor functions at the same time on the latest version.Pin 25 is
12V brake switch input port.Pin1 is motor temperature sensor input port.
(15)Optional joystick throttle. A bi-symmetrical 0-5V signal for both forward and reversing.
(16)Configurable motor over-temperature detection and protection with the recommended
thermistor KTY84-130 or KTY84-150.
(17)3 hall position sensor inputs. Open collector, pull up provided.
(18) Brake analog regen mode.This regen mode doesn't need brake switch to support any more.Only
available from software version 0106.KLS controller can not support reflashing.
(19)Enhanced regen brake function. A novel ABS technique provides powerful and smooth regen.The
regen can happen at any speeds until zero speed.

Features:
1)Intelligence with powerful microprocessor.
2)Synchronous rectification, ultra low drop, fast SVPWM and FOC to achieve very high efficiency.
3)Electronic reversing.
4)Voltage monitoring on 3 motor phases, bus, and power supply.
5)Voltage monitoring on voltage source 12V and 5V.
6)Current sense on all 3 motor phases.
7)Current control loop.
8)Hardware over current protection.
9)Hardware over voltage protection.
10) Configurable limit for motor current and battery current.
11) Low EMC.
12) LED fault code.
13) Battery protection: current cutback, warning and shutdown at configurable high and low battery
voltage.
14) Rugged aluminum housing for maximum heat dissipation and harsh environment.
15) Rugged high current terminals, and rugged aviation connectors for small signal.
16) Thermal protection: current cut back, warning and shutdown on high temperature.
17) Configurable 60 degree or 120 degree hall position sensors.Controller can do auto_Identification
angle for different degrees of hall sensors.
18) Configurable high pedal protection: the controller will not work if high throttle is detected at
power on.
19) Current multiplication: Take less current from battery, output more current to motor.
20) Easy installation: 3-wire potentiometer will work.
21) Standard PC/Laptop computer to do programming.There is one more choice for customers to
program KLS controller.Standard Tablet with Android OS to do programming.Need a Z-TEK USB TO
RS232 cable for connecting the controller to App program in Tablet.
22) User program provided. Easy to use. No cost to customers.
23) Support motors with any number of poles.
24) Up to 70,000 electric RPM standard. (Electric RPM = mechanical RPM * motor pole pairs;Motor
pole pairs=Motor poles/2).

General Specifications:
•Frequency of Operation: 20kHz.
•Standby Battery Current: < 0.5mA.
•5V or 12V Sensor Supply Current: 40mA.
•Controller supply voltage range: PWR, 18V to 90V for controllers rated equal or lower than 72V.
•Supply Current, PWR, 30mA Typical.
•Configurable battery voltage range, B+. Max operating range: 18V to 1.25*Nominal Voltage.
•Standard Throttle Input: 0-5 Volts(3-wire resistive pot), 1-4 Volts(hall active throttle).
•Throttle Input: 0-5 Volts. Can use 3-wire pot to produce 0-5V signal.
•Main Contactor Coil Driver<2A.
•Full Power Operating Temperature Range: 0℃ to 70℃(MOSFET temperature).
•Operating Temper ature Range: -40℃to 100℃ (MOSFET temperature).
•Motor Current Limit, 10 seconds boost: 300A ,depending on the model.
•Motor Current Limit, continuous: 120A ,depending on the model.
•Max Battery Current :Configurable.

3. Sabvoton Controller SVMC96100.

MQ(Sabvoton) 100A 96V DC Controller - SVMC96100
1) Model: SVMC96100
2) Available Battery Voltage: 48V-96V
3) Available Motor Power: 2KW - 2.5KW
4) Peak DC Current: 100A
5) Phase Peak Current: 250A
6) Working Communication: Hall Sensor
7) Installation Size: 247mm * 147mm * 62 mm
8) Weight: 2.2kgs
9) Defaut Throttle Working Voltage: 0V - 5V
10) Mosfets Detail: 24FET
11) Case Material: Aluminum
12) Controller Design: Sine Wave hall sensor DC controller, 100A electric motorcycle controller
13) Support Programmable by PC & Phone
14) Certification: CE, CCC

Features:
1, FOC-180° sinusoidal drive controller applied to BLDCM or PMSM..
2, It takes only 3 minutes for the motor to be well matched on its best electronic angle at the first
time.
3, The motor torque ripple will be reduced to the minimum, so as to ensure electric vehicle to run
without any noise and vibration, smoothly, and comfortably.
4, The precise current ring can provide accurate torque input to meet the requirement 0f large
torque output during vehicle starting and climbing.
5, The controller enjoys high efficiency due to space vector converter control algorithm which can
effectively reduce the temperature rise of controller and extend battery life mileage
6, Built-in various protection: locked-rotor protection, over-current protection, overload protection,
over-temperature protection, speed protection, over-voltage protection ,under-voltage protection
and so on, effectively ensuring the safety of electronic control system and vehicle.
7, System status and fault intelligent management system can effectively monitor the current
system operating mode external input state ,the case of system failure, and the LED flashes at the
same time to facilitate the diagnosis and maintenance.
8, The rich peripheral interfaces: reverse, cruise, anti-theft, electronic brake, etc.
9, Parameter modifications and settings are available through online configuration with online
computer
10,CAN BUS is optional to communicate with body instrument and BMS

4. Votol EM-100: It is Sine Wave Controller ( Sinusoidal Controller) for electric bike, bicycle,
motorcycle, motorbike, scooter, tricycle and other small vehicle.

Votol Controller EM-100

Type: Sine Wave Controller, Sinusoidal Controller, Hall Sensor Type.
Voltage: 48V-72V (max. 90V).
Battery Current: 100A (maximum).
Phase Current: 330A (maximum).
Flux Weakening Ratio: 200%.
Size: 218 x 124 x 62mm.
Weight: 1.650kg
Main Funtion
3-Speed.
Boost/Sport.
Reverse.
High Brake.
Re-Generating.
Flux Weakening, increase the speed of motor.
EM-100 Controller is suitable for 2000W, 3000W DC Brushless Hub Motor and Mid Drive Motor.