Manual

> INSTALLING PRIVA COMPASS

Contact
Priva (head office)
Zijlweg 3
2678 LC De Lier
The Netherlands

See www.priva.com for contact information of a Priva office or partner for your region.

Article number: 5001018

Version: 00.019
Date: December 2020

© Copyright Priva B.V. All rights reserved.

No part of this publication may be reproduced, published or stored in a retrieval system without
written prior permission of Priva.

This publication has been developed with care. However, the products shown may differ in dimensions
and design from the actual products. Priva will not accept any responsibility for damages caused by
any errors or deficiencies in this publication. Priva may modify its products and the associated
manuals without prior notice. Priva advises to check product, installation, hardware and if present
software on irregularities.

Priva owns the patents, patent applications, trademarks or other intellectual property rights regarding
the products described in this publication. With this publication Priva does not grant the use of the
aforementioned intellectual property rights. Product and company names this publication may not
be used without the permission of Priva.

All Priva products and services are subject to the relevant Priva general terms and conditions. These
general terms and conditions can be read and downloaded at www.priva.com/general-conditions.
Contents
About this manual ............................................................................................ 6
Related documents .............................................................................................................................. 6
Target groups and required competencies ....................................................................................... 6

Safety ................................................................................................................. 8
Safety - general ..................................................................................................................................... 8
Electrical safety ..................................................................................................................................... 8

Warranty ............................................................................................................ 9

Functions and intended use ............................................................................ 9

Compass system overview ............................................................................ 10

Compass cabinet components ..................................................................... 11

Compass FG terminals ....................................................................................................................... 13

Overview of connecting sensors and systems ............................................ 14

Compass system installation steps .............................................................. 15

General installation ............................................................................................................................ 15
Installing field equipment ................................................................................................................. 15
Position the Compass cabinet .......................................................................................................... 15
Cable grommets and glands ............................................................................................................. 17
Connecting the mains cable .............................................................................................................. 17
Setting the mains voltage on the 24 VAC transformer .................................................................. 19
Connecting Ethernet cables .............................................................................................................. 19
Connecting WLAN .............................................................................................................................. 21
Using the alarm output ..................................................................................................................... 21
Switching the Compass system on and off ..................................................................................... 22
Commissioning Compass .................................................................................................................. 23
Updating Compass software ............................................................................................................ 27
IP address assignment ...................................................................................................................... 28
Maintenance, checking and calibration ........................................................................................... 29
Replacing fuses ................................................................................................................................... 29
Troubleshooting the Compass system ............................................................................................ 30
Performing a reset of the VDC power supply ................................................................................. 30

Priva Blue ID hardware .................................................................................. 31

Earth contact ....................................................................................................................................... 31
Switching system power on and off ................................................................................................. 31
Connecting field equipment ............................................................................................................. 32

Installing Priva Compass - 00.019 1

Priva

Connections - RS485 .......................................................................................................................... 32

Connecting hardware ........................................................................................................................ 33
Disassembling hardware ................................................................................................................... 39
Maintaining hardware ....................................................................................................................... 41

Priva weather station WSC11 ........................................................................ 42

Principle ............................................................................................................................................... 42
Positioning the weather station ....................................................................................................... 43
WSC11 Connection ............................................................................................................................. 43
Mounting of WSC11 ........................................................................................................................... 46
Specifications ...................................................................................................................................... 47

Meteorological station .................................................................................. 51

Meteorological station ...................................................................................................................... 51
Positioning the meteorological station ............................................................................................ 51
Fitting the sensors .............................................................................................................................. 51
Ridge direction meteorological station ............................................................................................ 53
Mounting the mast ............................................................................................................................. 53
Maintenance of Meteorological station ........................................................................................... 55
Meteorological station specifications .............................................................................................. 55

Weather interface WI2 ................................................................................... 57

Connecting sensors to the Weather interface WI2 ........................................................................ 57
Connecting the Weather interface WI2 to a universal input ......................................................... 59
Extending cabling ............................................................................................................................... 59
Setting the Weather interface WI2 jumpers .................................................................................... 60
Specifications ...................................................................................................................................... 62

Linear light sensor LS2 and LS2WI ............................................................... 64

Linear light sensor .............................................................................................................................. 64
Mounting ............................................................................................................................................. 64
Connecting .......................................................................................................................................... 65
Maintain linear light sensor .............................................................................................................. 65
Specifications ...................................................................................................................................... 66

Radiation sensor CM3P .................................................................................. 67

Radiation sensor CM3P ..................................................................................................................... 67
Installation .......................................................................................................................................... 67
Connecting .......................................................................................................................................... 68
Solari CM3P maintenance ................................................................................................................. 68
Specifications ...................................................................................................................................... 69

Rain sensor RD2WI ......................................................................................... 70

Rain sensor ......................................................................................................................................... 70

2 Installing Priva Compass - 00.019

 Mounting ............................................................................................................................................. 70
Connecting .......................................................................................................................................... 71
Speeding up the initial rain detection .............................................................................................. 71
Rain sensor maintenance .................................................................................................................. 71
Specifications ...................................................................................................................................... 72

Wind direction sensor WDS2WI .................................................................... 73

Wind direction sensor ........................................................................................................................ 73
Mounting ............................................................................................................................................. 73
Connecting .......................................................................................................................................... 73
Maintenance of wind direction sensor ............................................................................................ 74
Specifications ...................................................................................................................................... 74

Wind speed sensor WSS2WI ......................................................................... 75

Wind speed sensor ............................................................................................................................ 75
Mounting ............................................................................................................................................. 75
Connecting .......................................................................................................................................... 76
Wind speed sensor maintenance ..................................................................................................... 76
Specifications ...................................................................................................................................... 77

Outside temperature sensor OTS2 ............................................................. 78

Outside temperature sensor ............................................................................................................ 78
Connecting .......................................................................................................................................... 78
Mounting ............................................................................................................................................. 79
Outside temperature sensor maintenance .................................................................................... 79
Specifications ...................................................................................................................................... 80

Flow sensor ..................................................................................................... 82

Connecting .......................................................................................................................................... 82
Cleaning the flow sensor ................................................................................................................... 83
Technical specifications – flow sensor ............................................................................................. 83
Technical specifications - T-piece for flow sensor .......................................................................... 83

pH interface ..................................................................................................... 86
Connecting the pH interface ............................................................................................................. 86
Calibrating the pH interface .............................................................................................................. 86
Technical specifications - pH-interface ............................................................................................ 86
Technical specifications – pH sensor ............................................................................................... 87

Dosing Channel Driver ................................................................................... 88

Operation of Dosing Channel Driver ............................................................................................... 88
Connecting the Dosing Channel Driver ........................................................................................... 89
Specifications Dosing Channel Driver .............................................................................................. 90

Installing Priva Compass - 00.019 3

Priva

EC-DSS interface ............................................................................................. 92

Operation of EC-DSS interface .......................................................................................................... 92
Connecting the EC-DSS interface ..................................................................................................... 92
Expanding the EC-DSS interface ....................................................................................................... 93
Technical specifications - EC-DSS-interface ..................................................................................... 93
Connecting the Compass EC sensor ................................................................................................ 94
Specifications for EC sensor .............................................................................................................. 95
Calibrating the EC sensor (Compass) ............................................................................................... 95

Drain water sensor ......................................................................................... 97

Use ....................................................................................................................................................... 97
Overview .............................................................................................................................................. 98
Mounting the Drain water sensor .................................................................................................... 98
Connecting the Drain water sensor (Compass) ............................................................................ 100
Specifications of the Drain water sensor 1 kΩ ............................................................................. 101

Groscale ......................................................................................................... 102

Layout ................................................................................................................................................ 103
Preparing for installation ................................................................................................................ 104
Installation ........................................................................................................................................ 105
Connecting Groscale to Compass .................................................................................................. 107
Commissioning ................................................................................................................................. 108
LEDs ................................................................................................................................................... 111
Operation and display ..................................................................................................................... 111
Explanation menus .......................................................................................................................... 113
Maintenance Groscale ..................................................................................................................... 117
Replacement and repair .................................................................................................................. 117
Troubleshooting ............................................................................................................................... 118
Technical specifications ................................................................................................................... 119

Other sensor connection examples ........................................................... 120

Connecting I/O to universal input .................................................................................................. 120
Connecting I/O to digital input ....................................................................................................... 122
Connecting I/O to analog output ................................................................................................... 124
Connecting I/O to relay output ....................................................................................................... 124
Points to be considered .................................................................................................................. 125
Abbreviations used .......................................................................................................................... 125

Disposing of waste products ...................................................................... 126

General Compass specifications ................................................................ 127

Electrical specifications ................................................................................................................... 127
Other specifications ......................................................................................................................... 128

4 Installing Priva Compass - 00.019

 WLAN specifications ........................................................................................................................ 128
Preconditions for installation and use .......................................................................................... 129

General specifications of Priva Blue ID C-Line controllers and

modules ......................................................................................................... 130
Specifications of Priva Blue ID C4 C-MX34 Controller ................................................................. 132
Specifications of Priva Blue ID C-Line MX34 Mix input/output module ................................... 135
Specifications of Priva Blue ID C-Line UI8 Universal input module .......................................... 136
Specifications of Priva Blue ID C-Line DOR6 Relay output module ........................................... 137
Specifications of inputs and outputs ............................................................................................. 138
LEDs and line-up LED ....................................................................................................................... 142

EC Declaration of Conformity .................................................................... 146

Declaration of Conformity for environmental conditions ....................... 147

Installing Priva Compass - 00.019 5

Priva

About this manual

This manual provides information on installing and maintaining the Compass system. The manual
specifically focuses on the field equipment in a Compass system.

This manual is intended only for installers and service engineers, not for users.
A Compass Operator manual is available for users. User documentation must be available
in the workplace.

The manual deals with the following topics:

• the components of Compass
• installing and connecting field equipment to the Compass cabinet
• specifications
• resolving errors

Related documents

Document Article no. Availability

insert sheet on connecting and suspending Compass - included in the box of the Compass cabinet
Compass Operator manual - as Help in the Compass Operator
Compass price list - download as a PDF via the Priva Support
Portal: https://support.priva.nl (registered
partners only)

Priva Blue ID C-Line documentation

Document Article no. Availability
Installing and commissioning Priva Blue ID C-Line manual 5001010 • download as PDF via the Priva Support
Communicating with Priva Blue ID C-Line manual 5001011 Portal: https://support.priva.nl
(registered partners only)
Priva Blue ID C-Line connection examples 5001012 • view in your browser via the Manuals
datasheet Priva Blue ID C-Line system overview 5001135 and other documentation link in the Top
Control installation menu
Priva Blue ID C-Line Quick Reference Card 5001013
datasheets for the Priva Blue ID C-Line hardware various

Target groups and required competencies

Target group Tasks and responsibilities Training, knowledge and experience required
installers / service the system: • technical training in the field of electrical
engineers • transport engineering and process engineering
• position • experience with electrical installations for
• install the horticulture industry
• commission and set up • command of (technical) English
• test after initial commissioning and
resolve any problems
• operate
• perform an annual check
• take it out of operation and dispose of it
at end of service life

Explanation of symbols in this document

DANGER
Instruction to prevent physical injury or damage to the product, the installation or the
environment.

6 Installing Priva Compass - 00.019

 About this manual

CAUTION
Instruction to prevent problems with the product or the service.

INFORMATION
Additional information.

TIP
A tip or other useful information.

Installing Priva Compass - 00.019 7

Priva

Safety
• Before starting to work with the product, read the entire manual so that you are familiar
will all safety instructions and safety precautions.
• In addition, read any other manuals supplied with specific components.

Safety - general
• Use the system only for its intended purpose.
• Follow the instructions in this manual and the related manuals.
• Making alterations to the safeguards and safety icons on the equipment is prohibited.
• Both the installer/service engineer and the user must regularly check and maintain the equipment
(the safeguards in particular) in accordance with the instructions in this manual. Keep the
equipment clean and the surroundings tidy.
• Report malfunctions or damage to your installer immediately. Take the equipment out of
operation and do not use it if a defect is found.
• Only use original spare parts for repairs (refer to the spare parts price list).
• After making repairs check the correct status and functioning of the equipment.
• If the user allows personnel to operate the equipment, he/she must adequately instruct this
personnel. In particular this should cover the safety risks and safety instructions stated in this
manual. He/she must also supervise correct compliance with the instructions.
• Display the safety icons that are applicable in the room where the equipment is set up.
• Position the cabinet in a space that meets the environmental requirements.
• Make sure the space and the cabinet are easily accessible. There must be enough space to open
the cabinet for maintenance and installation. This is especially important if you need to switch
off the system with the circuit breaker in the event of problems.
• Keep water out of the cabinet. Do not use a high pressure cleaner to clean the cabinet.
• Do not use aggressive cleaning agents, scouring sponges or abrasives for cleaning.
• Damage to Compass components may occur as a result of:
• Incorrect transportation or storage.
• Incorrect installation and assembly.
• Incorrect environmental conditions.
• Wearing, aging or metal fatigue.

Electrical safety

The unit is powered from the mains voltage. There is a potential hazard of electrocution or fire
resulting from a short circuit. You must therefore adhere to the following safety instructions:

• Keep the housings of electrical components closed.

• Keep the electrical parts dry.
• Make sure the earthing is connected according to the principle "make contact first, break contact
last". The earth wire must therefore be twice as long as the phase wire and neutral wire.
• Ensure that the unit is connected to its own fuse group with the correct fuses.

During installation, maintenance or while resolving faults it may be necessary to open the housing
for the electrical components. In this case, adhere to the following safety instructions:
• Preferably, make the unit totally free of electricity by removing the plug from the socket outlet,
switching off the circuit breaker or by removing fuses from the fuse group.
• If the unit cannot be made free of electricity then take extreme care. Use well-insulated tools
and do not touch the ends of wires, connections and electrical components with your bare
hands. Keep the surroundings dry and ensure that there is someone close by to keep an eye on
you.
• Wear an earthed wrist strap when working in the cabinet. Otherwise the electronic components
may be damaged due to static electricity.

8 Installing Priva Compass - 00.019

 Warranty

Warranty
The warranty expires if the product is not installed, used and maintained in accordance with the
instructions in the Priva manual. For more details refer to the general terms of delivery (Priva will
supply these on request and refer to www.priva.com) and the specifically agreed terms of delivery.

Functions and intended use

The function of the Compass system is to control, regulate and monitor equipment in the horticulture
industry in order to maintain an optimum environment for the crop. Connected field equipment is
controlled from the Compass cabinet. The field equipment consists of various sensors and other
systems for the horticulture industry.

Installing Priva Compass - 00.019 9

Priva

Compass system overview

A Compass system always consists of a Compass cabinet to which field equipment such as sensors
can be connected. On account of to the many different possible combinations of field equipment,
almost every Compass system will be different. Below there is an example of a comprehensive
configuration.

The Priva Compass price list gives an overview of the sensors and systems that are supported.

A. Compass cabinet E. EC-DSS interface

B. Weather station F. EC sensor
C. pH interface G. Drain sensor system
D. pH sensor H. Other sensors

The Compass cabinet is the heart of the Compass system. The Priva Blue ID controller in the Compass
cabinet controls the system and the sensors or actuators are connected to the inputs and outputs
of the Priva Blue ID modules. Sensors are connected directly to the inputs and outputs of the modules
or are connected via interfaces, such as the pH interface.

The components are supplied separately. An installer positions the separate components and
connects them to each other.

10 Installing Priva Compass - 00.019

 Compass cabinet components

Compass cabinet components

The Compass cabinet consists of the following main components:
• a controller for controlling the system
• modules with inputs and outputs for connecting the sensors or interfaces
• a gateway for configuring the system or controlling the system via a smartphone
• power supplies for the components in the cabinet and the connected sensors

Compass 4S hardware configuration

A. 0 V and 24 V connections (both VAC and VDC) E. 24 VDC system power supply
B. circuit breaker F. 24 VDC power supply field equipment
C. 24 VAC transformer G. DIN rail with controller and space for expansion modules
D. 24 VAC fuse H. DIN rail with Mix I/O module and space for expansion
modules

Installing Priva Compass - 00.019 11

Priva

Compass 2S hardware configuration

A. 0 V and 24 V connections (both VAC and VDC) E. 24 VDC system power supply
B. circuit breaker F. 24 VDC power supply field equipment
C. 24 VAC transformer G. DIN rail with controller and space for expansion modules
D. 24 VAC fuse

Door and underside of Compass 4S and Compass 2S

A. Priva Gateway (mounted on the door) B. buzzer (on the bottom of the cabinet)

12 Installing Priva Compass - 00.019

 Compass cabinet components

Compass FG terminals
The Compass cabinet has multiple sets of FG terminals. The FG terminals must not be used randomly.
The FG terminals are specific to the different modules in the cabinet. Extension modules are delivered
separately and must therefore be connected with the correct FG terminals after installation.

Compass 4S

FG terminals Compass 4S

FG terminals For
X4.1 … X4.5 C4 C-MX34 controller
X4.6 … X4.7 UI8 extension module 1
X4.8 … X4.12 MX34 Mix I/O module
X4.13 … X4.14 UI8 extension module 2

Compass 2S

FG terminals Compass 2S

FG terminal For
X4.1 … X4.5 C4 C-MX34 controller
X4.6 … X4.7 UI8 extension module 1

Installing Priva Compass - 00.019 13

Priva

Overview of connecting sensors and systems

The following sensors and systems can be used in a Compass system and can be connected to the
Compass cabinet.

Sensor, interface or system Article number Connect to

Weather station WSC11 3779240 RS485 input of Priva C4
Weather interface WI2 3771351 universal input of a Priva Blue ID module
24 VDC power supply
24 VAC power supply
Meteorological station with: 3771009
Wind speed sensor 3779203 Weather interface WI2
Outside temperature sensor 3779204 Weather interface WI2
Rain sensor 3779206 Weather interface WI2
Wind direction sensor 3779215 Weather interface WI2
Linear light sensor LS2WI 3779205 Weather interface WI2
0-50 mV
Linear light sensor LS2 0-5 V 3779213 universal input of a Priva Blue ID module
24 VDC power supply
24 VAC power supply
Solari / radiation sensor 3779207 Weather interface WI2
Snow sensor 3779000 potential-free contact, connect directly to the universal
input of a Priva Blue ID module
24 VAC power supply
Air humidity sensor 3779219 4 … 20 mA, connect directly to the universal input of a Priva
Blue ID module
universal input of a Priva Blue ID module
24 VAC power supply
EC-DSS interface ¹ 3771051 universal input of a Priva Blue ID module
24 VDC power supply
24 VAC power supply
EC sensor, short, with NTC 1 3771052 EC-DSS interface
kΩ/25°C (inline)
EC sensor, long, with NTC 1 3771041 EC-DSS interface
kΩ/25°C (angled)
Drain sensor system 3779224 EC-DSS interface
pH interface 3771056 universal input of a Priva Blue ID module
24 VDC power supply
24 VAC power supply
pH sensor 3779046 pH interface
Priva Measuring Box T+RH ² 3779024 universal input of a Priva Blue ID module
24 VDC power supply
24 VAC power supply
Priva Measuring Box T 3779027 universal input of a Priva Blue ID module
Guardian CO2 monitor 3795044 universal input of a Priva Blue ID module
90 … 260 VAC power supply (50 - 60Hz)
Water temperature sensor 3779013 universal input of a Priva Blue ID module
Soil temperature sensor 3779016 universal input of a Priva Blue ID module
Priva Groscale weighing system 3771140 universal input of a Priva Blue ID module
24 VDC power supply
24 VAC power supply
Dosing Channel Driver 3770170 analogue output of a Priva Blue ID module
24 VAC power supply
¹ connections for 2 EC sensors or 2 Drain sensor systems
² temperature sensor and relative air humidity sensor are connected separately

14 Installing Priva Compass - 00.019

 Compass system installation steps

Compass system installation steps

General installation
The general installation steps for Compass are explained in the Compass insert sheet. The Compass
insert sheet is included in the box of the Compass cabinet.

The Compass insert sheet explains how to perform the following steps.
1. Suspension of the Compass cabinet.
2. Connect the power supply to the Compass cabinet.
3. Switch on the Compass system.
4. Connect the laptop and run the initial configuration.
5. Install extra Priva Blue ID hardware.

The insert sheet shows the basics of connecting field equipment, but cannot display details for all
field equipment. This manual provides additional information and details that are necessary for
installing and connecting field equipment, e.g. for commissioning (see Commissioning Compass
(page 23)).

To be able to commission a new Compass, both the Gateway and the controller must be
equipped with the latest version of the software. This software is available at
https://support.priva.com, under Priva Compass, in the article Where can I find the latest Priva
Compass software?. Save these files on your laptop.

Make sure you have a software licence, which can be purchased via web production.

Installing field equipment

Perform these steps to install and connect field equipment:
1. Install the weather station.
2. Install the pH sensor.
3. Position the pH interface.
4. Connect the pH sensor to the pH interface.
5. Connect the pH interface to the Compass cabinet.
6. Install the EC sensor.
7. Install the Drain sensor system.
8. Position the EC-DSS interface.
9. Connect the DSS to the EC-DSS interface.
10. Connect the EC sensor to the EC-DSS interface.
11. Connect the EC-DSS interface to the Compass cabinet.
12. Install other sensors.
13. Connect other sensors to the Compass cabinet.
14. Test the Compass system.

Position the Compass cabinet

De Compass cabinet is heavy. Lift the cabinet with 2 persons or use a suitable lifting device.

Installing Priva Compass - 00.019 15

Priva

When positioning the cabinet, bear the following in mind:

• Position the cabinet against a wall or other solid background.
• Ensure there is sufficient space around the cabinet.
• Ensure there is sufficient space underneath the cabinet to feed the wiring through.
• Ensure there is sufficient space above and next to the cabinet for the dissipation of heat.
• Use the 4 specified mounting holes for installing the cabinet.
• Use M8 bolts or M8 screws that can bear the weight of the cabinet.
• The cabinet is heavy. Have more than one person hold the housing in the correct position while
placing it. Or use a suitable lifting device.
• Position the cabinet in a space that meets the environmental requirements.
• Make sure the space and the cabinet are easily accessible. There must be enough space to open
the cabinet for maintenance and installation. This is especially important if you need to switch
off the system with the circuit breaker in the event of problems.

Mounting holes

Recommended space (in cm) to be left free around the cabinet

16 Installing Priva Compass - 00.019

 Compass system installation steps

Cable grommets and glands

The underside of the Compass cabinet has various types of cable grommets with cable glands. The
cable glands are intended for various types of cabling. Always use a cable grommet and gland that
is associated with a cable type with the specified cable diameter.

Always close a cable gland with a supplied dummy plug if a cable grommet is not being used.

Cable grommet / Number Cable type Cable diameter

gland
PG21 2 Ethernet 10 … 18 mm
optical fibre ¹
M20 2 mains power supply 6 … 12 mm
other cabling
M25 6 (Compass 2S) cabling for field equipment 9 … 16 mm
10 (Compass 4S)
¹ optional

Connecting the mains cable

Always switch off the mains power supply when you are working on electrical connections.

PE: Protective Earth (ground) L: Line (phase)

N: Neutral !!: Length of earth wire = 2x length of phase wire

Use a mains cable with a diameter of 5 … 10 mm. This is suitable for the M20 cable gland.

Installing Priva Compass - 00.019 17

Priva

1. Strip around 10 cm from the outer sheath of the mains cable.

2. Cut the wires to length. Make sure the earth wire is twice as long as the phase wire and the
neutral wire.
3. Strip the wires.
4. Feed the mains cable through the M20 cable gland.
5. Connect the earth wire (PE) to the earth terminal next to the circuit breaker.
6. Connect the neutral wire (N) to input 2 of the circuit breaker.
7. Connect the phase wire (L) to input 4 of the circuit breaker.
8. Screw tight the cable gland.

If you need to disconnect the mains cable, first disconnect the phase wire (L) and neutral wire (N),
and then disconnect the earth wire (PE) last.

18 Installing Priva Compass - 00.019

 Compass system installation steps

Setting the mains voltage on the 24 VAC transformer

The Compass cabinet is suitable for various mains voltages. The transformer converts the mains
voltage to the 24 VAC system power. You must set the locally used mains voltage on the transformer.
When the Compass cabinet is delivered, the phase wire is connected to an unused terminal on the
input side of the transformer.

1. Switch off the circuit breaker.

2. Disconnect the power cable to the cabinet from the mains supply.
3. Unplug the phase wire from the unused terminal.
4. Connect the phase wire to the terminal that corresponds to the local mains voltage.
Example: Europe has a 230 VAC network. In Europe, therefore, connect the phase wire to the
230 V terminal.
5. Check the connections of the neutral wire and earth wire. These are already connected upon
delivery.

Connecting Ethernet cables

Use Ethernet cables that meet the specifications.

The Priva Gateway connects the Compass system via ethernet to the controller and to a local network
or a laptop for configuring the system. The Ethernet cable to the controller is already connected to
the ETH2 of the Priva Gateway when the cabinet is delivered. The Ethernet cable for a connection
to a local area network or laptop is connected by you to ETH1 of the Priva Gateway.

1. Feed the Ethernet cable through the PG21 cable gland.

2. Connect the Ethernet cable to ETH1 on the Priva Gateway.
3. Screw tight the cable gland.

Priva Gateway factory settings

Management level (office environment)
ETH1 IP address DHCP (if no DHCP present: 172.16.1.1 or 192.168.1.2 for
older systems)
ETH1 subnet mask DHCP (if no DHCP present: 255.255.255.0)
Automation level (process computers)
ETH2 IP address 172.17.1.2 (or 192.168.1.1 for older systems)
ETH2 subnet mask 255.255.255.0
URL http://<gateway name>/ ¹
http://<IP address>/ ²
¹ the gateway name is configured by the customer during the initial configuration of the system.
² If DNS is not used and the Windows hosts file has not been modified.

Installing Priva Compass - 00.019 19

Priva

Network specifications

Physical layer 100BASE-TX 100BASE-FX 1000BASE-LX

Network protocol Fast Ethernet (IEEE Fast Ethernet (IEEE Gigabit Ethernet (IEEE
802.3u) 802.3u) 802.3, clause 38)
Supported network classes • A, B and C
• Classless Inter-Domain Routing (CIDR) where IP-codes with a
" / " can be used

Permitted network topology line, star or ring network (or a combination of these)
Maximum number of Ethernet switches to be • 50 in a ring network (HiPER Ring requirement)
connected • 50 in a line network (because of response time)

Maximum ring network configuration time in 300 ms

normal operation
Connect to switched on Compass yes

Cabling specifications

Physical layer 100BASE-TX 100BASE-FX 1000BASE-LX

Cable required F/UTP cable, category fibre optic cable fibre optic cable
6 (multi-mode, 50/125 (multi-mode, 50/125
micrometer) micrometer)
Maximum cable length per segment 100 m 2000 m (when 550 m
prescribed cable is
used)
Baud rate 100 Mbit/sec 100 Mbit/sec 1 Gbit/sec
Galvanic isolation per segment no yes yes

20 Installing Priva Compass - 00.019

 Compass system installation steps

Connecting WLAN
For the WLAN connection, you do not need to install or configure anything.

The WLAN adapter is already connected to the Priva Gateway’s USB port when the cabinet is delivered.
When the Priva Gateway is switched on, the WLAN adapter installs itself and the wireless network
is set up automatically.

After a restart of the Gateway, it may take a few minutes before the wireless network is
available.

Data for wireless network

Network name PRIVADA-XXXXXXX
(or the name configured by the customer)
Password welcome@priva

Factory settings for WLAN adapter

IP address 192.168.137.1
Subnet mask 255.255.255.0
DHCP Enabled
SSID PRIVADA-XXXXXXX
WLAN security protocol WPA2-PSK

Using the alarm output

The alarm output is a relay that is controlled based on alarms within the network of controllers. This
alarm output is also activated if there are communication problems within the network. The
connection depends on the alarm reporter. The Normally Closed (NC) relay is generally used, and
is therefore open if there is no supply voltage or if there is an alarm.

Faults in the controller can be sent to the outside as alarm signals via the controller’s on-board alarm
output (A). This way, you are quickly informed about an active alarm or fault in the system by a lamp
or alarm dialer that is connected to the alarm output. The alarm signal stops when it is acknowledged.
Also when the alarm itself is no longer active, but was not acknowledged yet, the alarm signal remains
active until it is acknowledged.

The buzzer in the Compass control cabinet is connected to analog output 1. This output
switches synchronously with the alarm output.

Installing Priva Compass - 00.019 21

Priva

Switching the Compass system on and off

Switch on
1. Switch on the Compass system by switching on the circuit breaker.
2. Switch on the controller and the Mix I/O module (if present) with the on/off button. See Switching
system power on and off (page 31).
This automatically switches on the other Priva Blue ID modules that are connected to the
controller and Mix I/O module.

Switch off
1. Perform a shutdown of the controller. See Performing a shutdown (page 39).
2. Switch off the controller and the Mix I/O module (if present) with the on/off button. See Switching
system power on and off (page 31).
3. Switch the Compass system off by switching off the circuit breaker.
This switches off the power supplies in the Compass cabinet, which automatically switches off
the sensors that are powered by the system.

Testing
Perform the following tests after switching on the system or in the event of malfunctions.

1. Check the LEDs on the controller, the Mix I/O module and expansion modules.
The blue line-up LED (all modules) must be on continuously.
The green status LED for controller (C) (on controller only) must be on continuously.
The green status LED for I/O (I/O) (all modules) must be on continuously.
2. Check whether the power indicator LEDS on the power supplies are on.
3. Check the LEDs on the Priva Gateway.
The green LED for the supply voltage must be on continuously.
The green LED for SSD activity will flicker when information is being written to the hard disk.
4. Test the operation of the sensors.
See the chapters in this manual for the relevant sensor or the manuals of connected systems.

See also Troubleshooting the Compass system (page 30).

22 Installing Priva Compass - 00.019

 Compass system installation steps

Commissioning Compass

Preparation
To be able to commission a new Compass, both the Gateway and the controller must be equipped
with the latest version of the software. This software is available at https://support.priva.com, under
Priva Compass, in the article Where can I find the latest Priva Compass software?. Save these files on
your laptop.

Setting up the Priva network

The Priva network is an industrial network separated from your office network, and is only used for
Priva products.

The Gateway creates a separation between the Priva network and the office network with the aid
of 2 network ports. The Priva network is connected to the second network port on the Gateway
(ETH2 or LAN2).

Each Compass controller has a built-in switch with 4 ports. The Priva network can be connected to
any of these ports. If you have several Compass controllers or other Priva products in the Priva
network, you can decide how the network infrastructure should be set up. A subsequent controller
can be connected directly to the built-in switch or via an external switch. The desired degree of
operational safety determines your choice of network infrastructure.

Before connecting the office network to the Gateway, you must first commission the Compass.

Gateway

From your laptop or another mobile device (tablet or mobile phone), you can start Gateway setup
via Wi-Fi or via a wired network connection.

Installing Priva Compass - 00.019 23

Priva

Via Wi-Fi
Make sure the Wi-Fi dongle is inserted into one of the Gateway’s USB ports before starting Gateway
setup. After starting Gateway setup, it takes a few minutes before the Gateway’s Wi-Fi network can
be seen in the list of wireless network connections on your laptop or mobile device.

By default, the Gateway name begins with PRIVADA- followed by a number of characters. Establish
the Wi-Fi connection between your laptop and the Gateway. The Wi-Fi password is welcome@priva.

Open a web browser (Internet Explorer, Chrome, Edge or Firefox) and go to http://192.168.137.1 to
start Gateway setup.

Via wired network connection

Go to the Ethernet properties of your laptop’s network card and choose an IP address in the Gateway
range, for instance IP address 172.16.1.134 (192.168.1.134 for older systems) with subnet mask
255.255.255.0.

Connect your laptop to the first network port (ETH1 or LAN1) on the Gateway using a network cable.

Open a web browser (Internet Explorer, Chrome, Edge or Firefox) and go to http://172.16.1.1 (or
http://192.168.1.2 for older systems) or http://PRIVADA-xxxxxxx to start Gateway setup.

Gateway setup

Update Gateway software

The first time that Gateway setup launches, it will prompt you to update the Gateway software. Choose
Select update file to update the software with the Gateway setup file from the preparation stage. The
file will then be uploaded to the Gateway, which verifies the file. The Gateway update process may
take up to 15 minutes.

Once the update has been completed, the home screen will reappear. To continue, select Not now;
the update has already been carried out.

Creating authorisations
No authorisations are defined in the factory settings; you select them yourself. The first step is to
select a 5-digit PIN code that protects access to Gateway setup and Compass setup. Save this code
carefully!

Next, you create a user name for the Operator in the format of an e-mail address, such as
[email protected]. The Gateway also uses this user name as a temporary password for
logging on to the Operator for the first time. When logging on for the first time, the user changes
this temporary password to a password of his/her choice. Save the user name and password carefully!

Tab: settings
You will now be taken to the Settings tab of Gateway setup. Select Edit next to the Time zone to choose
the correct time zone for the location in which the Compass has been installed. You should also set
the correct date and time.

You can also rename the Compass. Bear in mind that the name PRIVADA-xxxxxxx will change and
that you must use the new name (if there is a DNS server) or IP address in the browser to access
the Gateway setup and the local Operator. The use of punctuation marks, such as spaces, '@', '/' and
'#', in the name is not allowed.

Tab: network
The Compass is supplied with default IP addresses. These must be changed to prevent network
conflicts. Compare the IP address with your home address; it must be unique to ensure that mail
arrives correctly.

Ethernet 1 is intended for connecting the Gateway to your office network. By default, this port
automatically receives an IP address from your office network. This will generally work well, but it
depends on your office network. Your IT administrator can give you more information on that.

24 Installing Priva Compass - 00.019

 Compass system installation steps

Please note that the office network may not automatically issue an IP address. In that case, use an
IP address for Ethernet 1 in the same range as the office network.

Ethernet 2 is the Priva industrial network for the controller(s). Use a different IP range for this network
than that of your office network, e.g. 172.17.16.80.

It is possible that Ethernet 3 is now being used for the Wi-Fi network with the dongle. Apart from
that, it is not used.

Tab: preferences
Set your preferences here for the language of the local Operator and the units used.

Compass setup

Update device
On the Settings tab of Gateway setup you can see the controllers that the Gateway has detected in
the Priva network.

Select Update device. You will now be taken to Compass setup.

The controller’s IP address must be in the same range as Ethernet port 2 of the Gateway to which

the controller is connected, e.g. 172.17.16.85. Change the controller’s IP address by clicking on
next to the IP address. You can change the IP settings by typing them yourself or by selecting Auto
assign. Once the changed settings have been saved, the controller needs some time to implement
the changes.

Click on the button in the top right-hand corner of Compass setup.

Select Upload platform image to update the software with the Controller Setup file from the preparation
stage. The file will then be uploaded to the controller, which verifies the file. You will then be prompted
to confirm the update. The controller update process takes approximately 5 minutes.

Tab: network
After updating the controller software, you will see the Network tab of Compass setup where you can
adjust the network settings. This has already been done and you can proceed to the next step.

Tab: zones
On the Zones tab you can add the zones. A zone can be used as a zone for the climate area and at
the same time as an area for a water system, for instance.

Each controller can contain a maximum of 4 zones. When adding a zone, select the zone number
that you wish to use. These numbers do not have to be consecutive, but must always be unique
within the Compass system, including in the event that there are several controllers.

Select Save to save the zone configuration.

Tab: software
Once the zones have been added, enter the licence code on the Software tab and confirm it with
Submit.

On the left-hand side of the browser page, you will then see the software options that have been
enabled by the licence code. On the right-hand side, you will see the zones that have been added
and the available software modules. You can distribute the software modules across the zones and
then click on Save.

Installing Priva Compass - 00.019 25

Priva

Tab: I/O connection

The software has been distributed across the zones and equipment must be connected to the
controller on the I/O connection tab.

Before we can allocate the inputs and outputs, check whether Compass setup is detecting the correct
hardware. On the left-hand side, you will see the hardware modules that are detected. If these match
the modules that are present, confirm them with Confirm.

If the modules displayed do not match what has been installed, check the cabling between the
modules and whether the controller (CMX34) and the extension module (MX34) are switched on.

After confirming the hardware module layout, you will also see a blue LED illuminate on each module.

You can now allocate sensors/actuators to the inputs and outputs for each zone. The list box for the
sensors/actuators depends on the licence and the assignment of the software modules to the zones.
Next, select the hardware module and the input or output for this sensor/actuator to which you
wish to connect the sensor/actuator. The software will display a suggestion. Select Assign to save the
assignment.

After allocating the inputs and outputs, save the list of I/O connections as an Excel file, as a
PDF file or as a file that can be imported on the same or a different controller (select Export).

Other controller settings

In the top right-hand corner of Compass setup you will see the button for the frequency of the
mains power supply (50 or 60 Hz), the buzzer volume and the option for updating the controller
software (Upload platform image).

At the top right of Compass setup there is also the button for exiting Compass setup and returning
to Gateway setup. Select this once Compass setup has been completed.

You will return to the Settings tab of Gateway setup.

To include the configured controller in the operating software, the final step is to connect this
controller to the Gateway by selecting Connect on the controller.

Repeat this procedure within Compass setup for each controller in the Compass system.

Once all the controllers have been commissioned, disconnect your laptop if you are connected to
the Gateway with an Ethernet cable. If the Compass is being operated via the office network or with
a Wi-Fi router for direct wireless operation, connect the Gateway’s Ethernet port 1 to your office
network.

Starting operation
To start the operating software, select the Gateway’s IP address in the address bar of a browser.

Go to Settings to set the latitude and longitude of the location in which the Compass has been installed.
This is important in order to synchronise the set times with the sunrise and sunset times.

26 Installing Priva Compass - 00.019

 Compass system installation steps

Updating Compass software

Preparation
Make sure that the following preparations have been made:
• Download the update packages for the Compass controller and for the Gateway. This software
is available at https://support.priva.com, under Priva Compass, in the article Where can I find the
latest Priva Compass software?
Save these files on your laptop.
• Be sure the two networks of the Gateway, the office network (ETH1) and the Priva network (ETH2),
are in seperate network ranges.
• Inform the customer/grower that the process computer can't control and can't be accessed
during the update procedure.
• Collect the user name and password to log into the Operator and the PIN code to access the
Gateway setup or someone should be able to log in.
• Be sure that all controls for climate, energy and irrigation are in rest and in a safe position.

• Be aware that the updates of the Controller and the Gateway may take some time (up
to an hour).
• Update of both the Controller and the Gateway is required (if new software is available),
otherwise the communication will get lost.

Update procedure

Update the Compass controller first and then the Gateway to prevent communication being
lost.

1. Start the Local Operator and log in with the customer’s user name and password.
2. Open the apps by clicking the apps button.
3. Click on the Gateway setup button.
4. Use the PIN code to log in the Gateway setup.
5. Once the Gateway setup screen is shown, navigate to the Controller by clicking on the Device
Setup button on the controller icon.
6. Open the Settings menu by clicking on the sprocket in the upper right corner of the display.
7. Select Upload platform image and you will be prompted to select your update file.
8. Open the file “Compass_ControllerSetup_xxxxxxxx.zip” and confirm the update.
9. A blue page is shown for a while and then a status bar appears. This will take about five minutes
and your controller will reset at one point during the update. After the update is finished, the
controller will restart, and you will see the Compass setup screen.
10. Go back to the Gateway setup by clicking the “exit” button.
11. Repeat steps 5-10 to update each controller in your network.
12. To update the Gateway, go to the Gateway setup screen and select Upload package.
13. Open the file “Gateway_Setup_x_x_x_xxxxxxxx.zip”.
14. Once the file is uploaded, you need to confirm that you want to update the Gateway.

Do not switch off the Gateway at this time!

15. The Gateway setup screen will reappear once the update is completed.
16. For each controller, press the Reconnnect button to load the updated controller screens into the
gateway.
17. When the updates are completed, you will need to make a backup of the settings and IO of your
controller to protect yourself against data loss. Click on the Device setup button on the controller.
•Reopen the Settings menu by clicking on the sprocket in the upper right corner of the display.
•Press the Backup button to make a backup of the settings and IO configuration for your
controller.
• Save this backup in a secure place.
18. Repeat step 17 for each controller.
19. Go back to the Gateway setup by clicking the Exit button.
20. From the gateway setup screen, press Start Operator to return to your normal operation.

Installing Priva Compass - 00.019 27

Priva

IP address assignment
Both Connext, Compass and FS Performance projects use fixed IP addresses. When assigning IP
addresses, use the following rules and format:
• For a class B network with an address space of 65535 addresses, for instance, choose the address
range 172.17.16.X. The network mask will be 255.255.240.0.
• Use the same range for each greenhouse. For instance:
• Greenhouse 1 – 172.17.16.1 to 172.17.16.255
• Greenhouse 2 – 172.17.17.1 to 172.17.17.255
• Group system components per function.
• Record the used IP addresses in FDCT (also FS Performance projects) and on a plan.

Group Function IP series Maximum number

Greenhouse 1 Operation (Gateway, POD 172.17.16.1 to 172.17.16.30 30
Server/Clients, FS
Performance Server / Clients,
Panel PC, DAP, etc.)
Spare 172.17.16.31 to 172.17.16.39 9
Switches 172.17.16.40 to 172.17.16.79 40
Compass 172.17.16.80 to 172.17.16.99 20
CPC (CLIMATE, WATER, 172.17.16.100 to 20
ENERGY) 172.17.16.119
Transrouters 172.17.16.120 to 40
172.17.16.159
Spare 172.17.16.160 to 20
172.17.16.179
Service 172.17.16.180 to 20
172.17.16.199
Third-party application 172.17.16.200 to 20
(LeenHuisman, Hotraco, 172.17.16.219
Priva LWE, DHCP Server)
Spare (or DHCP range) 172.17.16.220 to 35
172.17.16.254
Greenhouse 2 Operation (Gateway, POD 172.17.17.1 to 172.17.17.30 30
Server/Clients, FS
Performance Server / Clients,
Panel PC, DAP, etc.)
Spare 172.17.17.31 to 172.17.17.39 9
Switches 172.17.17.40 to 172.17.17.79 40
Compass 172.17.17.80 to 172.17.17.99 20
CPC (CLIMATE, WATER, 172.17.17.100 to 20
ENERGY) 172.17.17.119
Transrouters 172.17.17.120 to 40
172.17.17.159
Spare 172.17.17.160 to 20
172.17.17.179
Service 172.17.17.180 to 20
172.17.17.199
Third-party application 172.17.17.200 to 20
(LeenHuisman, Hotraco, 172.17.17.219
Priva LWE, DHCP Server)
Spare (or DHCP range) 172.17.17.220 to 35
172.17.17.254

28 Installing Priva Compass - 00.019

 Compass system installation steps

Maintenance, checking and calibration

Cleaning
Clean the outside of the Compass cabinet with a damp cloth.

• Keep water out of the cabinet.

• Do not use a high pressure cleaner to clean the cabinet.
• Do not use aggressive cleaning agents.
• Do not use abrasives.

Replacing fuses
The Compass cabinet has a fuse for protecting the 24 VAC supply voltage in the event of a short
circuit. Always replace a fuse with a fuse of the same type.

1. Switch the Compass system off with the circuit breaker.

2. Replace the fuse.
Use the correct type of fuse.
3. Switch the Compass system on with the circuit breaker.

Installing Priva Compass - 00.019 29

Priva

Troubleshooting the Compass system

Perform the following checks and steps if problems occur. If the problem persists, please contact
your Priva partner.

Malfunction Possible cause and solution.

System does not switch Check whether the cabinet is receiving power.
on Check whether the mains voltage has been set on the 24 VAC transformer.
Check whether the circuit breaker is switched on.
Check whether the controller and Mix I/O module are on.
Check the fuse.
Priva Blue ID modules Check whether the circuit breaker is switched on.
do not switch on Check the 24 VDC power supplies. The indication LEDs must be on.
Check whether the controller and Mix I/O module are on.
Check whether Priva Blue ID expansion modules are connected with the I/O bus cable to
the controller or Mix I/O module.
Please note: First switch off the modules before inserting an I/O bus cable.
Sensors are not Check the 24 VDC power supplies. The indication LEDs must be on.
receiving power Check the 24 VAC transformer.
Check external power supplies.
Check the fuse and the circuit breaker.
Check the connections.
No connection with Check the connection to the WLAN adapter or Ethernet connection.
Compass during the Refresh the browser.
Setup process

Performing a reset of the VDC power supply

Perform a reset of the power supply if the input of the VDC power is receiving power, but 24 VDC is
not present at the output. In that case, the DC OK LED will be off.

1. Switch the Compass system off with the circuit breaker.

2. Wait 30 seconds.
3. Switch the Compass system on with the circuit breaker.
4. Check whether the DC OK LED is on.
If the LED is not on, the 24 VDC power supply is defective or there is a short circuit in the system.

To determine if there is a short circuit and to find its source:

1. Switch the Compass system off with the circuit breaker.
2. Disconnect all 24 VDC common wires from the 24 VDC connecting terminals.
3. Switch the Compass system on with the circuit breaker.
4. Check whether the DC OK LED is on.
If the DC OK LED is off, the power supply is defective. Replace the power supply.
If the DC OK LED is on, there is a short circuit in the system. Continue with the next step to find
the source.
5. Connect the 24 VDC common wires to the connecting terminals one by one.
6. Check the DC OK LED after connecting each wire.
If the DC OK LED stays on after you have connected a wire, this wire does not cause a short
circuit.
If the DC OK LED goes out after you have connected a wire, this wire causes the short circuit.
7. Resolve the short circuit.
8. Switch the Compass system off with the circuit breaker.
9. Reconnect all wiring.
10. Switch the Compass system on with the circuit breaker.

30 Installing Priva Compass - 00.019

 Priva Blue ID hardware

Priva Blue ID hardware

The Compass cabinet has a Priva Blue ID controller and, optionally, a Priva Blue ID Mix I/O module
and other expansion modules. The controller and modules form part of the Priva Blue ID C-Line.
These chapters provide information about the Priva Blue ID C-Line hardware.

The Priva Blue ID C-Line has modules with and without manual operation and signalling.
Compass only uses Priva Blue ID C-Line modules without manual operation and signalling.

Earth contact

The modules have a functional earth contact (A). It is not therefore a safety earth. The functional
ground makes contact with the DIN rail when the hardware is installed. This guarantees the grounding
of the hardware, provided that the DIN rail itself is also earthed.

Switching system power on and off

A. on/off button

You use the on/off button (A) to switch the system power on and off.
• switch off: place button (A) in position 0
• switch on: place button (A) in position 1

Do not switch expansion modules off by removing the I/O bus cable.

Installing Priva Compass - 00.019 31

Priva

The expansion modules are powered via the I/O bus and do not have their own on-off button. If you
switch a controller or Mix I/O module on or off, the connected expansion modules will automatically
be switched on or off at the same time.

Connecting field equipment

• To install wiring in a terminal block, use a suitable screwdriver. See Screwdriver for terminal
block (page 34).
• For connecting, use only wiring as specified in General specifications of Priva Blue ID C-Line
controllers and modules (page 130).
• When using flexible wire, it is best to use crimp-on terminals.
• All terminal blocks are printed with an explanatory abbreviation; see the Connections section of
the relevant module in the chapter Connecting hardware (page 33).
• For the field power, use the 24 VDC power supply for field equipment. Do not use the 24 VDC
system power supply. This prevents any faults, such as a short circuit, in connected field
equipment having an effect on the Priva Blue ID hardware.

The modules have a number of common FG connections which serve as a 'neutral signal' for the
universal inputs, digital inputs and analogue outputs. The Priva Blue ID C-Line does not have any
field power for powering field equipment. Field equipment must therefore be powered externally.

Do not use the 24 VDC system power supply to power field equipement. Use the 24 VDC
power supply for field equipment.

1. Connect the field equipment to the desired inputs and outputs.

2. Connect the FG (Field Ground).
The FG serves as a 'neutral signal' for the universal inputs, digital inputs and analogue outputs.
Use the FG connection on the same module to which the input or output is connected.

The cabinet has different FG terminals for different modules. Use the appropriate FG
terminal for the module. See Compass FG terminals (page 13).

Connections - RS485

A RS485-A
B RS485-B
0 RS485-GND

32 Installing Priva Compass - 00.019

 Priva Blue ID hardware

Connecting hardware

Overview of a Priva Blue ID C-Line system

A Priva Blue ID C-Line system consists of one controller and one or more modules with I/O. A system
may consist of the controller alone, since the controller is equipped with various inputs and outputs.
If there is a need for more inputs and outputs, the system may be expanded with additional modules.

All modules are connected to each other via the I/O bus.

Connections
The hardware is equipped with the connections described in the table below. A picture of the
connections is provided and other details are described later in this chapter.

Hardware Connecting Number

Priva Blue ID C-Line hardware
C4 C-MX34 controller Power supply voltage (24 VDC) 1
I/O bus out 1
RS485 port 1
Ethernet port 4
Shield (for Ethernet ports) 1
Digital inputs 12
Universal inputs 8
Analogue outputs 6
Relay outputs 8
USB host 1
USB device 1
C-Line MX34 module Power supply voltage (24 VDC) 1
I/O bus in and out 2
Digital inputs 12
Universal inputs 8
Analogue outputs 6
Relay outputs 8
C-Line UI8 module I/O bus in and out 2
Universal inputs 6
C-Line DOR6 module I/O bus in and out 2
Relay outputs 6

For UL916 / CSA C22.2 No. 205: use UL-listed or CSA-certified wiring and crimp-on terminals.

Connectors
To make connections, use the supplied connectors or the optionally available right-angled screw
connectors. Right-angled screw connectors are supplied as a set for a module. The set contains the
right-angled screw connectors that are needed for the connectors on the module concerned.

Connecting with flexible wire

When using flexible wire, always use a crimp-on terminal.

With crimp-on terminals

1. Strip the wire:
• If using single crimp-on terminals: strip 10 mm off (8 mm for RS-485 connector).
• If using double crimp-on terminals: strip 12 mm off.
2. Fit the crimp-on terminal.

Installing Priva Compass - 00.019 33

Priva

3. Insert the crimp-on terminal into the terminal block until it can go no further.

Connecting with solid wire

1. Strip 10 mm off the wire.
2. Insert the wire into the terminal block until it can go no further.

Screwdriver for terminal block

To install wiring in a terminal block, use a screwdriver with the correct dimensions. For instance, a
Phoenix Contact Screwdriver SZF 1-0.6X3.5 (article number 1204517).

Using a screwdriver that is too large or too small may damage the connections on the modules.

Connecting the supply voltage

Connect the supply voltage to the controllers and the Mix I/O modules. The other modules are
powered via the I/O bus.

Use a power supply that meets the safety requirements laid down in General specifications
of Priva Blue ID C-Line controllers and modules (page 130).

• To install wiring in a terminal block, use a suitable screwdriver. See Screwdriver for terminal
block (page 34).
• When using flexible wire, it is best to use crimp-on terminals.

34 Installing Priva Compass - 00.019

 Priva Blue ID hardware

• All terminal blocks are equipped with an explanatory abbreviation; see the Connections sections
for the various connections.
• For Priva Blue ID projects, do not connect the FE terminal block. This terminal is intended for
possible future use.
For Compass, connect the FE terminal block.
• Switch the system power off before connecting devices to the modules; see Switching system
power on and off (page 31).

Connections - I/O bus

The right-hand I/O bus is the outgoing I/O bus. The left-hand I/O bus is the incoming I/O
bus. Always connect the right-hand I/O bus to the left-hand I/O bus of the next module.

Points to be considered when connecting the I/O bus

The I/O bus cables are not hot-pluggable. Always disconnect the system power from all
modules when removing or connecting I/O bus cables.

Connect the modules to each other via the I/O bus. Use the supplied I/O bus cables (10 cm) or a long
I/O bus cable (72 cm, article number 5219112). Always take the permitted I/O bus cable length into
account (maximum total length and maximum length between modules).

The controller's I/O bus connector has a dust cover. Remove the dust cover before connecting an
I/O bus cable. No I/O bus cable is connected in the outgoing I/O bus connector of the last module;
always install a dust cover there

Connections - digital input

DI digital input
FG (Field Ground) common neutral for input

Installing Priva Compass - 00.019 35

Priva

Connections - universal input

UI universal input
FG (Field ground) common neutral for input

Connections - analogue output

AO analogue output
FG (Field ground) common neutral for output

Connections - relay output

COM common contact

NO (normally open) normally open contact, open when output is not powered
NC (normally closed) normally closed contact, closed when output is not powered

Points to be considered

The use of mains wiring is not permitted in the Compass cabinet.

36 Installing Priva Compass - 00.019

 Priva Blue ID hardware

A low voltage wiring

• Always use a crimp-on terminal with flexible wiring.

• Avoid short circuits by bundling and fixing both the mains wiring and the low voltage
wiring as close to the connector as possible. See picture above.
• Compared to the mains wiring, the low voltage wiring must be double insulated. The
cross section and insulation of the mains wiring must comply with applicable local
installation regulations.
• If double crimp-on terminals are used, the sum of the currents of all the relay outputs
of the same module may not exceed 20 A.
• During maintenance work on field equipment connected to a relay output, or when
removing a connector of a relay output, always turn off the mains power supply using
an external local isolator. An open relay contact must not be considered to be a safe
separation.

Across inductive loads (such as a reed switch) use a spark extinguisher. This significantly
extends the service life of the switch contacts.

Ethernet connections
With the Ethernet connections on the controller you can connect the system to a network. The
Ethernet connections do not provide Power over Ethernet (PoE).

Connecting an Ethernet port

The shielding of the Ethernet ports is fitted externally to the shield connection on the controller. The
Shield connection is located below the Ethernet ports. In principle, this shielding does not have to
be connected, as this is coupled internally and at a high frequency (capacitive coupling) with the
functional earth (FE). The shield connection only has to be connected directly to the functional earth
(FE) if communication problems arise as a result of low-frequency electromagnetic interference.

Installing Priva Compass - 00.019 37

Priva

Connections - alarm output

COM common contact

NO (normally open) normally open contact, open when output is not powered
NC (normally closed) normally closed contact, closed when output is not powered

38 Installing Priva Compass - 00.019

 Priva Blue ID hardware

Disassembling hardware

When working on the system, be careful with regard to parts carrying a dangerous voltage.

Performing a shutdown
In the case of a shutdown, the running processes on the controller are closed down properly. This
relates, for instance, to read and write actions to memory and communication with other modules
and systems.

1. Depress button (A) and hold it down for 2 seconds.

2. Release button (A).
The shutdown is complete when the blue LED is off and the green I/O LEDs flash.

Disassembling hardware
1. Perform a shutdown.
2. Switch the system power off.
3. Turn off the voltage for the entire system.
4. Label the wiring before disconnecting it.
5. You can remove the connectors complete with wiring, or disconnect the wiring from the
connectors.
Remove a connector by gently pulling it forward.
Disconnect the wiring from the connector by pressing the catch (A) with a screwdriver and
removing the wire.

Do not turn the screwdriver. This will damage the hardware.

Installing Priva Compass - 00.019 39

Priva

6. Unlock the hardware by placing a screwdriver in the blue locking clip on the bottom of the
module and pushing it down.

7. Tilt the bottom of the module forwards

8. Lift the module up and out of the DIN rail.

40 Installing Priva Compass - 00.019

 Priva Blue ID hardware

Maintaining hardware

Replacing the controller battery

• Replace the battery while the controller is on, or the time setting will be lost.
• Priva recommends that the controller battery should be replaced once every five years.

The controller contains one battery. The battery can be replaced while power is connected.

1. Remove the battery holder and battery.

2. Take the old battery out of the battery holder.
3. Install the new battery in the battery holder. Pay attention to the polarity.
The controller will trigger an alarm if no battery has been inserted or if the battery has been
inserted with the incorrect polarity.
4. Install the battery holder and battery in the controller.
5. Dispose of the old battery as chemical waste.

Cleaning hardware

• Avoid contact with live parts.

• Make sure that no water runs into the electrical components.

The following safety precautions apply for cleaning the housing of the hardware:
• Use insulating gloves.
• Remove dust using a soft brush.
• Clean the plastic housing with a slightly damp, soft, lint-free cloth.
• Use warm water only, with a few drops of washing-up liquid if necessary. Do not use solvents
or corrosive or gaseous cleaning agents.

Installing Priva Compass - 00.019 41

Priva

Priva weather station WSC11

The Priva weather station WSC11 integrates all the measurements that are relevant to the horticulture
industry in a single compact station.

The following measurements are available when the weather station is used with the Compass:
• Wind speed
• Wind direction
• Global radiation (Radiation sensor)
• Rain alarm
• Outside temperature
• Relative humidity

Principle
Wind speed / wind direction

Wind measurement is based on the hot wire principle. The bottom is equipped with a heated
cylindrical sensor. The supplied heat energy is a measure of wind speed.

The metal cylinder contains 4 temperature-measuring resistors. These resistors are thermally coupled
with the cylinder and positioned according to the 4 points of the compass. When an incident flow
affects the cylinder as a function of the wind direction, this is accompanied by a temperature gradient
which is registered by the measuring resistors. The relationships between the 4 temperature values
are used to calculate the wind direction.

Light

The light measurement is carried out via 4 silicium photo sensors, which are aligned to the 4 cardinal
directions in the mean elevation angle (40°).

Twilight

Twilight is calculated from the sum of the 4 measuring values of the direction-independent light
sensors.

Global irradiance

A silicon PIN photodiode is used to measure global irradiance. The sensor is positioned horizontally
and registers the diurnal values of the solar irradiation intensity.

Precipitation

The detection of precipitation is based on capacitance measurement. The sensor is installed in the
housing cover. An integrated heating system adjusts the sensor area to an overtemperature in
relation to the ambient temperature. This overtemperature (approximately 2K) prevents bedewing
of the sensor surface. The thermal output is increased with precipitation. This accelerates drying of
the sensor, allowing the time at which precipitation ended to be identified more accurately.

Air temperature

A PT1000 measuring resistor is used to measure the air temperature. The sensor is mounted on a
flexible printed board and positioned in the lower section of the housing.

42 Installing Priva Compass - 00.019

 Priva weather station WSC11

Air pressure

Absolute air pressure is measured with a piezoresistive MEMS sensor.

Time / date and geostationary data

The WSC11 has a GPS receiver with a built-in RTC (Real Time Clock). This allows it to receive the
position of the WSC11 (degree of longitude/latitude, local altitude) time (UTC) and date. The GPS
receiver does not need alignment. The built-in RTC is buffered with a backup capacitor and retains
its data without a voltage supply for a period of minimum 3 days.

Position of the sun (elevation / azimuth)

On the basis of the GPS data the current sun position is calculated every second.

Humidity measurement

A built-in hygro-thermosensor is used to measure humidity levels. The sensor uses a small air
exchange and responds to changes in humidity within seconds. The relative humidity and air
temperature are used to calculate absolute humidity and the dew-point temperature.

Inside temperature of housing

A silicon temperature sensor measures the temperature inside the housing.

Positioning the weather station

To obtain representative measurements, keep in mind the following when selecting a location for
the weather station:
• Make sure that the weather station sticks out approximately 2 metres above the greenhouse
roof or shed roof.
• Do not position the weather station in the vicinity of, or in the shade of, buildings or trees for
example.
• To limit the effect of side-wall warming on the weather station, you should position the weather
station:
• not in the vicinity of a heat source such as chimneys or ventilation openings;
• in the northern hemisphere on the north side of the side-wall, or in the southern hemisphere
on the south side.
• Do not install the weather station in the vicinity of ceiling sprinklers.
• Install the weather station in such a way that it is not obscured by shadows. Bear in mind that
shadow propagation changes throughout the day.

WSC11 Connection
You can connect the WSC11 directly to the Priva Blue ID controller via an RS485 connection.

The WSC11 is supplied with a 15 metre cable. If the distance is greater than this, you must extend
the cable and take measures to ensure a stable connection.

Connection (max. 15 metres)

For distances up to 15 metres, you can connect the WSC11 directly to the Priva Blue ID controller
and to a 24 VDC power supply.

The power supply and the data bus are not electrically isolated.

Installing Priva Compass - 00.019 43

Priva

1. Connect the supplied sensor cable (AWG26) with the screw connector to the WSC11.
2. Calculate whether the 24 VDC power supply for Compass field equipment has sufficient capacity
to also power the WSC11. Add an extra power supply if the capacity is insufficient.
3. Connect the cores for power supply to the 24 VDC power supply for Compass field equipment.
4. Connect the cores for data to the RS485 port of the C4. See Connections - RS485 (page 32).

Connection (15 to 150 metres)

For distances greater than 15 metres, you must extend the cable. You must also terminate the RS485
network on both sides and ensure biasing.

• Requirements
• A junction box with an IP code of at least IP65.
• A terminating resistor of 120 Ω / ½ W
• An extension cable with 6 cores:
• 0.6 mm (AWG22)
• twisted pair
• shielded
• A bus termination and biasing on the side of the Compass. Use a Set networkterminator RS-485
+ resistor (article number 3771028).

44 Installing Priva Compass - 00.019

 Priva weather station WSC11

1. Connect the supplied sensor cable (AWG26) with the plug to the WSC11.
2. In a junction box, connect the cores of the sensor cable to the extension cable.
3. In the junction box, install a terminating resistor of 120 Ω / ½ W between the data+ and data-
line (the green and yellow core respectively of the sensor cable) as a bus termination.
4. Calculate whether the 24 VDC power supply for Compass field equipment has sufficient capacity
to also power the WSC11. Add an extra power supply if the capacity is insufficient.
5. Connect the cores for power supply to the 24 VDC power supply for Compass field equipment.
6. Connect the cores for data to the RS485 port of the C4. See Connections - RS485 (page 32).
7. Connect the biasing and bus termination module in accordance with the diagram below. For
the specifications, see Set networkterminator RS-485 + resistor (page 50).

The power supply and the data bus are not electrically isolated.

LEDs
The LEDs at the bottom of the WSC11 are visible through the housing.

Installing Priva Compass - 00.019 45

Priva

LED Behaviour Meaning

green flashing (1 Hz) The WSC is ready for operation and has not
received a query command for 3 seconds or
longer.
blue flashing The current wind speed.
The correlation between the flash frequency and
wind speed is shown in the following figure:

Mounting of WSC11
The working position of the WSC11 is horizontal (plug connection underneath). During
installation, de-installation, transport or maintenance of the WSC11 make sure that no water
gets into the device and connector.

The intended installation of the WSC11 requires:

• a tube with an outside diameter of ≤25mm and an inside diameter of ≥19mm
or
• a mounting bracket (optional, article no. 3779242)

1. If you are using a mounting bracket, remove the corner guides.

2. Pull the plug of the connecting cable through the tube or mounting bracket.

3. Mount the WSC11 on the tube or mounting bracket.

4. Use a compass to detect a prominent object (tree, building etc.) to the north.

46 Installing Priva Compass - 00.019

 Priva weather station WSC11

5. Orient the north indicator (N) of the WSC11 in the direction of this prominent object.

When aligning, bear in mind that the direction of a compass needle may differ from true
north and that there may be deviations on account of magnetic fields.

6. Secure the WSC11 with the M4 socket head screw (maximum torque 0.6 Nm).

Specifications

General

Article description Weather station WSC11

Article number 3779240
Operating voltage 18 ... 30 Vdc
Power consumption <300 mA at 24 Vdc
Temperature range -30 ... +60 °C
Humidity range Non-condensing
GPS reception GPS receiver with low power consumption, built-in RTC
and antenna
Holding time of RTC (without voltage supply) Approx. 3 days

Housing

Installing Priva Compass - 00.019 47

Priva

Material Polycarbonate
Dimensions See Dimension drawing
Weight 0.22 kg
Type of protection IP65 in working position
Type of connection 7-pin plug connector

Sensors (in combination with Compass)

Available measurements in combination with Compass • Wind speed

• Wind direction
• Global radiation (Radiation sensor)
• Rain alarm
• Outside temperature
• Relative humidity

Sensors

Wind speed
Type Thermal anemometer
Measuring range 0 … 40 m/s
Resolution 0.1 m/s
Accuracy To 10 m/s: ±1 m/s (rms - mean over 360°).From 10m/s:
±5 % (rms - mean over 360°).
Wind direction
Type Thermal anemometer
Measuring range 1 … 360°
Resolution 1°
Accuracy with laminar incident flow ±10°
Light (north, east, south, west)
Type Silicon sensor
Measuring range 0 … 150 kLux
Resolution 0.1 kLux
Accuracy ±3% (± 4.5 kLux)
Spectral range 475 ... 650 nm

Spectrum of light sensors/Directional characteristics of

light sensors
(Source: data sheet for component SFH5711 / OSRAM)
Twilight
Type Silicon sensor
Measuring range 0 … 999 Lux
Resolution 1 Lux
Accuracy ±10 Lux
Global irradiance
Type Silicon sensor
Measuring range 0 … 1300 W/m2
Resolution 1 W/m2
Accuracy ±10 % (± 130 W/m²)

48 Installing Priva Compass - 00.019

 Priva weather station WSC11

Spectral range 350 ... 1100nm

Spectrum for global irradiance sensor (Source: data

sheet for component TEMD5080X01 / VISHAY)
Precipitation
Type Ceramics, capacitive measurement, sensor area heated
Measuring range 1 / 0 (precipitation yes/no)
Thermal output, sensor dry, bedewing protection 0.1 W
Thermal output, sensor wet, drying phase 1.1 W
Temperature
Type PT1000
Measuring range -30 … +60 °C
Resolution 0.1 °C
Accuracy with wind speed >2m/s ±1 °C (-5 … +25 °C)
Air pressure sensor
Type Piezoresistive
Measuring range 300 … 1100 hPa
Resolution 0.01 hPa
Accuracy ±0.5 hPa at 20°C
Long-term stability ±0.1 hPa / year
Relative humidity
Type CMOS capacitive
Measuring range 0 … 100 % rel. humidity
Resolution 0.1 % rel. humidity
Accuracy with wind speed >2m/s ±10% rel. humidity at 20°C
Absolute humidity
Measuring range 0 ... 400 g/m3
Resolution 0.01 g/m3
Dew-point temperature
Measuring range -30 ... +60 °C
Resolution 0.1 °C
Inside temperature of housing
Type Silicon sensor
Measuring range -30 … +60°C
Resolution 0.1 °C
Accuracy ±2 °C
Digital interface
Type RS485
Mode Half-duplex mode
Baud rate 115200
Data format MODBUS RTU

Accessories

Article description WSC11 Connection cable

Article number 3779241
Length 15 m
Features Cable with cable socket on device side and open ends on reception
side.

Installing Priva Compass - 00.019 49

Priva

Article description Mounting bracket

Article number 3779242
Length 250 mm
Width 60mm
Material Stainless steel 1.4301
Features Used for lateral attachment of WSC11 to a vertical surface.

Set networkterminator RS-485 + resistor

article number 3771028

power supply 24 VDC
termination resistance 120 Ω
bias voltage 5V
bias resistances 510 Ω
dimensions (W x D x H) 27 x 60 x 89 mm
housing DIN rail mounting, IP40
ambient conditions 0°C to 50°C, 10 – 90% RH (non-condensing)

50 Installing Priva Compass - 00.019

 Meteorological station

Meteorological station

Meteorological station

The Meteorological station is designed for the optimum positioning of the weather sensors. By
installing these sensors at an adequate height, the effect of interference can be limited. The
Meteorological station is supplied as a kit comprised of two supports, two mast sections, clamping
blocks, wall brackets, and mounting materials. This chapter describes the composition and the
construction of the Meteorological station.

Positioning the meteorological station

See Positioning the weather station (page 43).

Fitting the sensors

Fitting sensors on the supports of the Meteorological station

The Meteorological Station has two supports on which a total of six sensors can be mounted. The
sensors must be fitted to specific positions on the supports.

The bottommost support must be situated in a north-south alignment, and the upper support must
be in an east-west alignment.

5 6

1 2 3 4 1 2 3 4

6 5

A B
A: further north than 15° N
B: further north than 15° N

Installing Priva Compass - 00.019 51

Priva

Position Weather sensor

Upper support
1 Wind direction sensor
2 Outside temperature sensor
3 Reserve position for expansion, for a Precipitation intensity sensor or Irradiation
sensor for instance.
4 Wind speed sensor
Bottommost support
5 Rain sensor
6 Linear Light Sensor or Radiation sensor (only with a geographical situation more
northerly than 15° NL or more southerly than 15° SL; otherwise place these sensors
on a separate mast)

To prevent the shadow of the Meteorological station falling on the Linear light sensor or the Radiation
sensor, the Linear light sensor or Radiation sensor must be positioned as follows:
• Further north than 15° N (in Europe for instance): position the sensor on the southern side of
the mast.
• Further south than 15° S (in Australia for instance): position the sensor on the northern side of
the mast.
• Avoid cast shadows at locations between 15° N and 15° S (near the Equator) mount the sensor
on a separate mast, on the upper support.

Fitting sensors on the universal mounting support

Sensors are fitted on the universal mounting support (article number 3779211) as follows:

1. If required, feed the cable for the sensor through the large hole in the mounting support, from
above.

Feed the cable carefully through the hole to help avoid damages to the cable.

2. Mount the sensor on the mounting support. You do so using the procedure for mounting a
sensor on a Meteorological station support.
3. Fit the crossbar to the Meteorological station using the brackets supplied with the kit, whereby
the clamping block is fitted between the mounting support and the Meteorological station.

Sensor fitted on mounting support

1. Sensor 4. Mounting brackets
2. Mounting support 5. Clamp plate
3. Meteorological station

52 Installing Priva Compass - 00.019

 Meteorological station

Ridge direction meteorological station

The meteorological station must be oriented based on 1 of the 8 points of the compass. This is
necessary because the settings in the Compass software are also based on one of the 8 point of the
compass. This means the meteorological station must be rotated when the ridge direction is in
between the point of the compass.

In the example below, the ridge direction is between north and north-west. When the meteorological
station is oriented north, the orientation of the window does not match north or north-west. Rotate
the meteorological station to closest point of the compass (North in this case). You can now set the
window orientation to North.

1. Window 2. Rotate meteorological station

Mounting the mast

To mount the mast, take the following steps:

Installing Priva Compass - 00.019 53

Priva

Position of the wall brackets

1. Mount both wall brackets above each other on the side wall so that the mast is positioned
vertically. See figure Position of the wall brackets (page 54). The distance between the brackets
must be at least 60 cm and the brackets must be securely mounted on the side wall.
2. Mount the first two clamping blocks on the top mast component near the socket, placing the
flat side on top. See the left-hand diagram in the figure Mounting the clamping blocks (page 55).
Fasten the blocks with the supplied bolts and nuts. Fasten the bolts uniformly.
3. Slide the small support on the mast component and fasten it to the clamp block with four bolts,
nuts and rings. (The small support has room for two sensors.)
4. Mount the other two clamping blocks at the top of the topmost mast component in the same
manner as described under step 2. See the right-hand diagram in the figure Mounting the
clamping blocks (page 55).
5. Place the large support on the mast component and fasten it to the clamp block with four bolts,
nuts and rings.
6. Mount the Rain sensor and the Linear light sensor or Radiation sensor on the bottommost
support. The Linear light sensor or Radiation sensor must be fitted onto the requisite opening.
Feed the cables of the two sensors through the hole in the clamp block into the mast component
so that the cable re-emerges on the underside of the mast component.

Make sure that the sensors are not damaged during the further installation.

7. Mount the other sensors on the top support and feed the cables through the mast component
downwards.

Pay careful attention to the position of the sensors on the support. Position the sensors
as described in chapter Fitting the sensors (page 51).

8. Slide the cap on the underside in both supports until they lock onto the clamp block.
9. Mount the plastic rings in the holes of the caps. These rings prevent the cap from coming loose
when being slid open.
10. Tape together the cables that come out of the underside of the mast component and feed the
cables through the bottom mast component.
11. Tighten the bottom mast component firmly in the socket of the top mast component and secure
the connection by screwing the two socket head screws tightly with the supplied socket head
key.
12. Place the mast in both wall brackets. The base of the mast must protrude at least 10 cm in
relation to the bottom wall bracket.
13. Turn the mast so that the weather sensors are in the position described in the chapter Fitting
the sensors (page 51).

54 Installing Priva Compass - 00.019

 Meteorological station

The sensors are supplied with 10-metre screened cable. It is recommend that you do not
shorten these cables when mounting the sensors. Coil the remaining length of cable or leave
a loop; this will simplify any future expansion of the Meteorological station with additional
crossbars of mast sections.

Mounting the clamping blocks

1. Upper mast section 4. Bolt for clamping block
2. Lower mast section 5. Nut for clamping block
3. Clamping block 6. Socket-head screw

Maintenance of Meteorological station

Check the condition of the mast section's fastening bolts at least once a year (the bolts must not be
rusted).

Meteorological station specifications

Construction two supports

two mast components
clamping blocks
wall brackets
installation material
Supports material aluminium (AlMg1)
Mast component material Al 50 St
Clamping block material aluminium
Wall bracket material galvanized steel
Dimensions (l x w x h) 500 x 700 x 3200 mm

Installing Priva Compass - 00.019 55

Priva

Configuration Article number

Meteorological station, including: 3771009
• Wind speed sensor
• Wind direction sensor
• Outside temperature sensor
• Rain sensor

Meteorological station, including: 3771024

• Wind speed sensor
• Outside temperature sensor

Meteorological station
1. Wind direction sensor 7. Support
2. Outside temperature sensor 8. Top mast component (160 cm)
3. Reserve position 9. Bottom mast component (160 cm)
4. Wind speed sensor 10. Wall bracket
5. Rain sensor 11. Clamping blocks
6. Linear light sensor

56 Installing Priva Compass - 00.019

 Weather interface WI2

Weather interface WI2

Not all sensors can be directly connected to an I/O module of Priva Blue ID connected; for these
sensors, the Weather interface WI2 is required. The interface ensures that the output signals of the
sensors are brought to the right level so that the controller can read them.

The interface is supplied in a splashproof housing, which enables it to be used either inside or outside.
In most cases, the interface will be mounted on or near the Meteorological station.

Connecting sensors to the Weather interface WI2

Connect the following to the interface:
• 24 VAC power supply for the interface
• sensors
• output signals of sensors to the Priva Blue ID modules.

Installing Priva Compass - 00.019 57

Priva

General
1. Unscrew and open the interface.
2.

Cable glands of Weather interface WI2

A. 24 VAC power supply E. Wind direction sensor
B. Output signals to I/O module F. Linear light sensor LS2WI
C. Rain sensor G. Outside temperature sensor
D. Wind speed sensor H. Reserve

Feed the wiring for the 24 VAC power supply, sensors and output signals through the correct
cable glands; see the figure Cable glands of Weather interface WI2 (page 58).
3. Connect the wiring from the various components to the connector terminals of the interface.
Connect the output signals of the sensors to the universal inputs of the Priva Blue ID modules.
See table Connections of Weather interface WI2 (page 58).

The power supply for the Weather interface WI2 must not be delivered by the same
power supply that powers the controller.

4. Only for a Linear light sensor or Radiation sensor CM3P: set the Weather interface jumpers. See
Setting the Weather interface WI2 jumpers (page 60).
5. Screw the interface closed

Connections of Weather interface WI2

Weather interface WI2 Sensors or power supply
Connector Name Group Wire colour Function
1 HIGH 24 VAC IN 24 VAC power supply for interface and sensors (electrically isolated)
1 LOW 0 VAC (24 VAC ± 15 %, 0.4 A, 10 VA)
2 HIGH 24 VAC IN
2 LOW 0 VAC
3 HIGH 24 VDC OUT 24 VDC power supply for external devices (100 mA)
3 LOW PGND

4 HIGH 24 VDC OUT 24 VDC power supply for external devices (100 mA)
4 LOW PGND

5 HIGH RGVW1 Rain sensor White Connection 1 heating element

5 LOW RGVW2 Brown Connection 2 heating element
6 HIGH RGKM1 Green Connection 1 measurement pattern
6 LOW RGKM2 Yellow Connection 2 measurement pattern
7 HIGH 24 VDC Wind speed sensor White 24 VDC power supply
7 LOW GND Brown Ground
8 HIGH WS IN Green Signal
8 LOW GND Yellow Ground

58 Installing Priva Compass - 00.019

 Weather interface WI2

Weather interface WI2 Sensors or power supply

9 HIGH 24 VDC Wind direction sensor White 24 VDC power supply
9 LOW GND Brown Ground
10 HIGH WR IN+ Green Signal +
10 LOW WR IN- Yellow Signal -
11 HIGH 24 VDC Linear light sensor White Do not connect (insulate core)
11 LOW GND LS2WI Brown Do not connect (insulate core)
or
12 HIGH LL/SOL+ Green Signal
Solarimeter CM3P
12 LOW GND Yellow Ground
13 HIGH GND Outside temperature White Connect to GND
13 LOW GND sensor Brown Connect to GND
14 HIGH BT+ Green Signal +
14 LOW BT- Yellow Signal -
15 HIGH RES IN Reserve connection - Signal (0–20 mA)
15 LOW GND (mA) - Ground
16 HIGH +12 V - +12 V power supply (100 mA)
16 LOW GND - Ground
17 HIGH RG OUT Output signals to according to Output of Rain sensor RD2WI
universal input requirements
17 LOW WS OUT according to Output of Wind speed sensor WSS2WI
requirements
18 HIGH WR OUT according to Output of Wind direction sensor WDS2WI
requirements
18 LOW LL/SOL OUT according to Output of Linear light sensor LS2WI
requirements
19 HIGH RES OUT - Output of reserve connection
19 LOW GND brown Ground for all output signals to universal
input
20 HIGH BT+ according to Outside temperature sensor OTS2 +
requirements
20 LOW BT- according to Outside temperature sensor OTS2 -
requirements

Connecting the Weather interface WI2 to a universal input

1. Connect the interface to a universal input. Use a shielded eight-cored cable, 0.8 mm (0.5 mm²).
2. In the Compass setup, select the correct sensor and, if applicable, the correct sensor type.

Extending cabling
You can extend the cable. Feed the cable from the sensor into a junction box (minimum IP code IP
65) and bridge the distance from the junction box to the Weather interface WI2 with a new shielded
cable.

Never use just tape to extend the cable.

Cable specifications
Cable type 4 x 0.8 mm (0.5 mm²), shielded
Maximum cable length 100 m

Installing Priva Compass - 00.019 59

Priva

Setting the Weather interface WI2 jumpers

The Weather interface has jumpers for setting the type of sensor (Radiation sensor CM3P and Linear
light sensor).

For the Radiation sensor CM3P:

1. Set up the WI2 jumpers as following:
• J2-A ON
• J2-B ON
• J2-C ON
• J2-D ON
• J2-E ON
• J2-F ON
• J2-G ON
• J2-S OFF
• J3 OFF
2. Find the calibration sensitivity on the calibration certificate of your CMP3 and enter it in as the
sunlight sensor multiplication factor in the weather calibration page. For instance, if your
calibration sensitivity is 22.73 x 10-6 V / (W/m2) , you will need to enter 2273 as the sunlight
sensor multiplication factor.

For the Linear light sensor:

1. Remove jumper J3.
2. Connect jumper S on J2:
3. Remove jumper G from J2.
4. Connect or remove the other jumpers in accordance with the table below and the sensor's
Radiation sensor factor. This value is stated on the supplied calibration certificate.

Sensor Sensor Jumper A Jumper B Jumper C Jumper D Jumper E Jumper F

radiation radiation
factor min factor max
343.64 X X X X X X
338.44 343.64 X X X X X -
333.41 338.44 X X X X - X
328.49 333.41 X X X X - -
323.72 328.49 X X X - X X
319.11 323.72 X X X - X -
314.63 319.11 X X X - - X
310.25 314.63 X X X - - -
305.99 310.25 X X - X X X
301.86 305.99 X X - X X -
297.85 301.86 X X - X - X
293.92 297.85 X X - X - -
290.09 293.92 X X - - X X
286.39 290.09 X X - - X -
282.78 286.39 X X - - - X
279.12 282.78 X X - - - -
275.55 279.12 X - X X X X
272.21 275.55 X - X X X -

60 Installing Priva Compass - 00.019

 Weather interface WI2

Sensor Sensor Jumper A Jumper B Jumper C Jumper D Jumper E Jumper F

radiation radiation
factor min factor max
268.94 272.21 X - X X - X
265.73 268.94 X - X X - -
262.60 265.73 X - X - X X
259.56 262.60 X - X - X -
256.59 259.56 X - X - - X
253.66 256.59 X - X - - -
250.81 253.66 X - - X X X
248.03 250.81 X - - X X -
245.32 248.03 X - - X - X
242.64 245.32 X - - X - -
240.03 242.64 X - - - X X
237.49 240.03 X - - - X -
235.00 237.49 X - - - - X
232.32 235.00 X - - - - -
229.70 232.32 - X X X X X
227.37 229.70 - X X X X -
225.08 227.37 - X X X - X
222.83 225.08 - X X X - -
220.63 222.83 - X X - X X
218.47 220.63 - X X - X -
216.37 218.47 - X X - - X
214.28 216.37 - X X - - -
212.24 214.28 - X - X X X
210.25 212.24 - X - X X -
208.30 210.25 - X - X - X
206.37 208.30 - X - X - -
204.47 206.37 - X - - X X
202.62 204.47 - X - - X -
200.81 202.62 - X - - - X
198.96 200.81 - X - - - -
197.14 198.96 - - X X X X
195.42 197.14 - - X X X -
193.73 195.42 - - X X - X
192.06 193.73 - - X X - -
190.42 192.06 - - X - X X
188.82 190.42 - - X - X -
187.24 188.82 - - X - - X
185.68 187.24 - - X - - -
184.14 185.68 - - - X X X
182.64 184.14 - - - X X -
181.17 182.64 - - - X - X
179.70 181.17 - - - X - -
178.27 179.70 - - - - X X
176.86 178.27 - - - - X -
175.47 176.86 - - - - - X
X = connect jumper
- = disconnect jumper

Installing Priva Compass - 00.019 61

Priva

Specifications

General
Article description Meteorological station interface WI2
Article number 3771351
Supply voltage 24 VAC ±15 %, 50/60 HZ
Power consumption (Weather interface WI2 only) 300 mA, 7VA
Connector terminals screw
Dimensions (L x W x H) 22 x 16 x 10 cm

Rain sensor
Rain alarm output voltage <1V
Output voltage dry message >4V

Wind speed sensor

Input frequency
Output range 0 – 1,47 V (0 ... 30 m/s)
Accuracy 8.4 %

Wind direction sensor

Input voltage, differential 0 – 5 V
Output range 1 .. 8 kOhm
Resolution 8 steps from 1 kOhm (45° compass rose, see table and figure
below)
Accuracy 7.4 % (25° compass rose)

Each of the 8 wind directions indicates a specific resistance value

Wind direction Resistance (kOhm) Voltage (mV) at Rt=3k01

N 1 1247
NO 2 1996
E 3 2496
SE 4 2853
S 5 3121
SW 6 3330
W 7 3465
NW 8 3633

62 Installing Priva Compass - 00.019

 Weather interface WI2

Linear light sensor LS2WI

Input high impedance (< 150 pA)
Output range 0 ... 50 mV (0 .. 150 klux)
Accuracy gain error: 4.75 %
offset error: 0.5 % (of the full scale)

Outside temperature sensor

Input/output (signal is only through wired) NTC 3000 Ω/25°C (-40°C ... 80°C)

Installing Priva Compass - 00.019 63

Priva

Linear light sensor LS2 and LS2WI

Linear light sensor

The Linear light sensor measures the intensity of the (sun)light, but not the infrared heat radiation.
This sensor is therefore not suitable for energy calculations.

The Linear light sensor consists of a photodiode whose output current is dependent on the quantity
of light collected.

The Linear light sensor should preferably be mounted on the Meteorological station and connected
to a Priva process computer.

The Linear light sensor is supplied with a calibration certificate. If the calibration certificate
is missing then you can request a duplicate from Priva. You will need to state the Linear light
sensor's serial number.

Mounting
1. Place the four-core female connector of the housing on the four-core male connector of the
Linear light sensor.
2. Place the Linear light sensor in the housing and tighten the hexagon-head bolt on the underside
of the housing. Make sure that the cover drops into the lock.
3. Unscrew the two socket head screws (including clamping rings) on the underside of the housing
completely.
4. Guide the cable through the appropriate opening on the mast.

The Linear light sensor has a set position on the mast.

Avoid cast shadows at locations between 15° N and 15° S (near the Equator) mount the
sensor on a separate mast, on the upper support.

5. Mount the Linear light sensor with the two socket head screws (including clamping rings) on the
support of the mast.
6. Feed the cable through the hole in the clamp block assembly into the mast section so that the
cable re-emerges on the underside of the block.

64 Installing Priva Compass - 00.019

 Linear light sensor LS2 and LS2WI

Interior of Linear light sensor

1. Cap with photodiode 3. Connector
2. Printed circuit board (9583)

The Linear light sensor is supplied with a 10-metre shielded cable. It is recommended that
you do not shorten this cable when mounting the unit. Coil the remaining length of cable
or leave a loop; This ensures that the cable will not be too short in the event of eventual
extensions with supports and mast components.

Connecting

Linear light sensor LS2

1. Connect the Linear light sensor LS2 to a universal input of the Priva Blue ID hardware.
2. Connect the cable as shown in the table below.

Colour Function Connection

White power supply 24 VDC
Brown power supply 0 VDC
Green sensor signal UI
Yellow Sensor GND (not electrically isolated) FG

Linear light sensor LSWI2

Connect the Linear light sensor to a universal input via the Meteorological station interface WI2. See
also Connecting sensors to the Weather interface WI2 (page 57).

Maintain linear light sensor

Clean the Linear light sensor's port at least once a year, or earlier if the Linear light sensor develops
measurement deviations. Clean the unit with a damp cloth and a little mild detergent if so required.

Do not use aggressive cleaning and/or abrasives!

Make sure that no moisture, dirt or dust enters the housing when opening the Linear light
sensor. This can negatively impact the measurement.

Installing Priva Compass - 00.019 65

Priva

Specifications

Linear Light Sensor LS2

Article description Linear Light Sensor LS2

Article number 3779213
Measurement principle photodiode
Spectrum 525 ... 1100 nm (50 % spectral sensitivity points)
Peak response 850 nm
Half angle 60°
Sensitivity 33 mV/klux
Measurement range 0 ... 150 klux
Output range 0 ... 5 V (not electrically isolated)
Supply voltage 21.6 .. 26.4 VDC
Protection short-circuit proof
24 VAC continuous
discharges 900 V/100 nF
Ambient temperature range -40 … 80 °C

Linear Light Sensor LS2WI (0 … 50 mV)

Article description Linear Light Sensor LS2WI (0 … 50 mV)

Article number 3779205
Measurement principle photodiode
Spectrum 525 … 1100 nm (50 % spectral sensitivity points)
Peak response 850 nm
Half angle 60°
Sensitivity 180 … 340 µV/klux (refer to calibration certificate)
Measurement range 0 … 160 klux
Output range 0 … 50 mV (depending on sensitivity, refer to calibration certificate)
Protection short-circuit proof
24 VAC continuous
discharges 900 V/100 nF
Ambient temperature -40 … 80 °C

66 Installing Priva Compass - 00.019

 Radiation sensor CM3P

Radiation sensor CM3P

Radiation sensor CM3P

The Radiation sensor (also called a pyranometer) measures a part of the spectrum of sunlight,
including the infrared part. The Radiation sensor therefore measures the quantity of incoming
radiation energy that the sun introduces into the greenhouse. You can use this sensor for energy
calculations.

The Radiation sensor CM3P consists of a black body with thermopile, the output signal of which is
dependent on the quantity of radiation collected.

The Radiation sensor CM3P is supplied with a calibration certificate. If the calibration
certificate is missing, you can also find the data on a sticker on the sensor. To do this, remove
the sensor from the black housing.

Installation
1. Remove the two socket head screws (including clamping rings) on the underside of the Radiation
sensor CM3P.
2. Guide the cable through the appropriate opening on the Meteorological station.

The Radiation sensor CM3P has a set position on the Meteorological station. See Fitting
sensors on the supports of the Meteorological station (page 51).

• Mount the Radiation sensor CM3P in such a way that the arrow on the housing is
pointing in the direction of the nearest pole.
• Avoid cast shadows at locations between 15° N and 15° S (near the Equator) mount
the sensor on a separate mast, on the upper support.

3. Mount the Radiation sensor CM3P with the two socket head screws (including washers) on the
support of the Meteorological station.
4. Feed the cable through the hole in the clamp block assembly so that the cable re-emerges on
the underside of the block.

Installing Priva Compass - 00.019 67

Priva

Cross section of the Radiation sensor CM3P

1 Thermopile housing 3 Connector
2 Printed circuit board (9583)

Do not shorten the supplied cable. Coil the remaining length of cable or leave a loop.
Exchanging and calibrating is only possible with an original cable, without additional costs
for replacing the cable.

Connecting
Connect the sensor to a universal input via the Meteorological station interface WI2. See also
Connecting sensors to the Weather interface WI2 (page 57).

Check operation
Check the operation of the sensor in daylight. Use a multimeter to measure the voltage across the
connecting terminals of the I/O module. Depending on the ingress of light, you must measure a
voltage between 0 mV (no light) and 50 mV (a lot of light).
2
In the Netherlands, the maximum radiation level in the summer is around 1000 W/m . With a
-2
sensitivity value of 18.6 µV/(Wm this results in an output voltage of 18.6 mV.

Solari CM3P maintenance

Clean the Radiation sensor CM3P at least once per year or more frequently if the Radiation sensor
CM3P begins to provide inaccurate measurements.Clean the unit with a damp cloth and a little mild
detergent if so required.

Do not use aggressive cleaning agents and/or abrasives.

Make sure that no moisture, dirt or dust enters the housing when opening the Radiation
sensor CM3P, since these can be detrimental to the measurement.
When closing the housing, be aware that the cover only fits in one position (tab fits in notch).

Checking by dealer
The Radiation sensor CM3P has been calibrated before delivery. Have the Radiation sensor CM3P
checked by your dealer once a year to guarantee correct and accurate measurement.

68 Installing Priva Compass - 00.019

 Radiation sensor CM3P

Customers in the Benelux can take out a maintenance contract with Priva for the Radiation
sensor CM3P. Your Radiation sensor will then be replaced with a calibrated sensor every
two years. Repairs are not included in this contract. If you have any questions concerning
the maintenance contract, please contact Priva.

Specifications

Article Radiation sensor CM3P

Article number 3779207
Measurement principle Thermopile (thermocouples)
Spectral sensitivity 305 - 2800 nm (50% spectral sensitivity points)
Sensitivity 7 - 25 μV/W/m² (see calibration certificate)
Response time 18 s (95%)
Measurement range -100 - 2000 W/m²
Output range -1 - 50 mV (depending on the sensitivity, see calibration certificate)
Course < 1% per year
Non-linearity +/- 2.5% (< 1000 W/m²)
Ambient temperature range -40 - +80 °C

Installing Priva Compass - 00.019 69

Priva

Rain sensor RD2WI

Rain sensor

The Rain sensors determines whether it is raining, and does so virtually immediately. Any rain falls
on the Rain sensor's grid of gilded copper. Droplets of water conduct electricity between the grid's
contact lines. A resistance measurement is carried out to detect any droplets between the contact
lines. The Rain sensor is equipped with heating to prevent condensation and to dry any rain droplets
quickly.

The Rain sensor should preferably be mounted on the Meteorological station and connected to a
Priva process computer.

The Rain sensor indicates solely that it is raining, where relevant; it does not measure the
precipitation intensity. In addition, the sensor is less suitable for the identification of hail or
snow.

Mounting
1. Unscrew the two socket head screws (including clamping rings) on the underside of the Rain
sensor completely.
2. Guide the cable through the appropriate opening in the mast.

The Rain sensor has a set position on the mast.

3. Mount the Rain sensor with the two socket head screws (including clamping rings) on the support
of the mast.
4. Feed the cable through the hole in the clamp block assembly so that the cable re-emerges on
the underside of the block.

70 Installing Priva Compass - 00.019

 Rain sensor RD2WI

Cross-section of Rain sensor

1. Contact surface + heating 3. Connector
2. Printed circuit board (9583)

The Rain sensor is supplied with a 10-metre shielded cable. It is recommended that you do
not shorten this cable when mounting the unit. Coil the remaining length of cable or leave
a loop; This ensures that the cable will not be too short in the event of eventual extensions
with supports and mast components.

Connecting
See Connecting sensors to the Weather interface WI2 (page 57) for how to connect the Rain sensor.

Speeding up the initial rain detection

After the connection and commissioning of the Rain sensor, the electronic systems require some
time before the rain detection functions properly. This time can be as long as 60 minutes when the
grid is dry. You can reduce this time to 1 minute as follows:
1. Place a clean wet sponge with tap water on the cartridge. Do not use demineralised water,
because it is not conductive.
The Rain sensor should detect rain after 1 minute.
2. Remove the sponge.
A short time after this, the Rain sensor should no longer detect rain.

Rain sensor maintenance

Clean the rain sensor at least once a year, or earlier if the Rain sensor develops measurement
deviations (for instance, due to leaves or bird droppings). Clean the unit with a damp cloth and a
little mild detergent if required. Also check for corrosion or any other damage to the surface of the
sensor. Replace the sensor if the surface has been damaged.

Do not use aggressive cleaning and/or abrasives. This damages the gilded contact surface
of the Rain sensor.

Make sure that no moisture, dirt or dust enters the housing when opening the Rain sensor.
This can negatively impact the measurement.

Installing Priva Compass - 00.019 71

Priva

Specifications

Article description Rain sensor

Article number 3779206
Measuring principle Determining the conductivity across copper pattern
Pattern material Copper, gilded
Track spacing 1.0 mm
Pattern area 16 cm
2

Pattern heating 1.5 – 6.0 W

Protection Continuous 24 VAC
Discharges 900 V/100 nF
Ambient temperature -40 – +80° C

72 Installing Priva Compass - 00.019

 Wind direction sensor WDS2WI

Wind direction sensor WDS2WI

Wind direction sensor

The Wind direction sensor determines the wind direction in a completely contactless manner and
supplies as an output signal a voltage between 200 mV and 3440 mV. Any value outside this range
is interpreted by the process computer as a sensor defect.

The Wind direction sensor should preferably be mounted on the Meteorological station and connected
to a Priva process computer.

Mounting
1. Unscrew the two socket head screws (including clamping rings) on the underside of the Wind
direction sensor completely.
2. Guide the cable through the appropriate opening on the mast.

The Wind direction sensor has a set position on the mast and can only be mounted in
one way on the support of the mast.

3. Mount the Wind direction sensor with the two socket head screws (including clamping rings) on
the support of the mast.
4. Feed the cable through the hole in the clamp block assembly into the mast section so that the
cable re-emerges on the underside of the block.
5. Check the direction of the Wind direction sensor with a compass. Turn the mast so that the
identifying mark on the housing of the Wind direction sensor points to the north.

Considering that the accuracy of the measurement depends strongly on the environment
(turbulence), you must reconsider the positioning of the Wind direction sensor with every
change in the surroundings (new buildings, tree growth).

The Wind direction sensor is supplied with a 10-metre shielded cable. It is recommended
that you do not shorten this cable when mounting the unit. Coil the remaining length of
cable or leave a loop; this will simplify any future expansion of the Meteorological station
with additional crossbars of mast sections.

Connecting
See Connecting sensors to the Weather interface WI2 (page 57) for how to connect the Wind direction
sensor.

Installing Priva Compass - 00.019 73

Priva

Maintenance of wind direction sensor

Check the wind direction sensor regularly for pollution and clean it if necessary. Pollution may cause
the wind vane to be obstructed. Clean the unit with a damp cloth and a little mild detergent if required.

Do not use aggressive cleaning agents or abrasives.

Make sure that no moisture, dirt or dust enters the housing when opening the Wind direction
sensor. This can negatively impact the measurement.

Specifications

Article description Wind direction sensor

Article number 3779215
Measurement principle optical or magnetic
Wind direction 0 – 359°
Resolution 1°
Measuring error 1°
Measurements/sec 20
Output signal Single ended
Output range 200 - 3440 mV
Supply voltage 18 – 40 VDC
Power consumption 15 mA (max)
Protection Continuous 24 VAC
Discharges 900 V/100 nF
Short circuit-proof output
Ambient temperature -40 – +80 °C

The output signal is divided across seven measurement zones, including two defect zones. See the
table below.

Output voltage (mV) Wind direction

0 – 200 Defect
200 – 920 North – East
920 – 1640 East – South
1640 – 2360 South – West
2360 – 3080 West – North
3080 – 3440 North – North-east
3440 – 4096 Defect

74 Installing Priva Compass - 00.019

 Wind speed sensor WSS2WI

Wind speed sensor WSS2WI

Wind speed sensor

The Wind speed sensor generates pulses at a frequency depending on the wind speed. The Wind
speed sensor consists of a rotor with interrupter disc, light source and photo diode.

The Wind speed sensor should preferably be mounted on the Meteorological station and connected
to a Priva process computer.

Mounting
1. Unscrew the two socket head screws (including clamping rings) on the underside of the Wind
speed sensor completely.
2. Guide the cable through the appropriate opening in the mast.

The Wind speed sensor has a set position on the mast and can only be mounted correctly
in one way on the support of the mast.

3. Mount the Wind speed sensor with the two socket head screws (including clamp rings) on the
mounting plate of the mast.
4. Feed the cable through the hole in the clamp block assembly so that the cable re-emerges on
the underside of the block.

Considering that the accuracy of the measurement depends strongly on the environment
(turbulence), you must reconsider the positioning of the Wind speed sensor with every
change in the surroundings (new buildings, tree growth).

Installing Priva Compass - 00.019 75

Priva

Cross-section of Wind speed sensor

1. Interrupter disc 3. Printed circuit board (9582)
2. Photodiode 4. Connector

The Wind speed sensor is supplied with a 10-metre shielded cable. It is recommended that
you do not shorten this cable when mounting the unit. Coil the remaining length of cable
or leave a loop; this will simplify any future expansion of the Meteorological station with
additional crossbars of mast sections.

Connecting
See Connecting sensors to the Weather interface WI2 (page 57) for how to connect the Wind
speed sensor.

Wind speed sensor maintenance

Check the Wind speed sensor regularly for pollution and clean it if necessary. Pollution and dust can
cause the paddle wheel to spin more slowly. Clean the unit with a damp cloth and a little mild
detergent if so required.

Do not use aggressive cleaning and/or abrasives!

Make sure that no moisture, dirt or dust enters the housing when opening the Wind speed
sensor. This can negatively impact the measurement.

76 Installing Priva Compass - 00.019

 Wind speed sensor WSS2WI

Specifications

Item description Wind speed sensor

Item number 3779203
Measuring principle Optic by means of interrupter disc
Measurement range 0 – 36 m/s
Just operate speed 1 m/s
Output type Power output with square wave
Frequency range 0 – 175 Hz, 4 pulses per rotation
Output current 0 or 2.5 mA
Duty cycle 60/40 (low/high)
Supply voltage 18 – 40 VDC
Supply current 17 mA (max)
Protection Continuous 24 VAC
Discharges 900 V/100 nF
Output short circuit proof
Ambient temperature -40° C – +80° C

Installing Priva Compass - 00.019 77

Priva

Outside temperature sensor OTS2

Outside temperature sensor

The Outdoor temperature sensor contains a temperature-dependent resistor with a negative

temperature coefficient (NTC) in a hermetically-sealed glass tube.

The Outside temperature sensor should preferably be mounted on the Meteorological station and
connected to a Priva process computer.

Connecting
The Outside temperature sensor can be connected both directly to a universal input, or via the
Meteorological station interface WI2.

Direct to universal input

1. Connect the sensor to a universal input of the Priva Blue ID hardware.
2. Connect the cable as shown in the table. No need to worry about polarity.

Connection of cable to universal input

Colour Function Connection
Green sensor signal UI
Yellow Sensor GND (not electrically isolated) FG
White None Not connected
Brown None Not connected

Cable type and length

You can extend the cable: feed the cable from the Outside temperature sensor to a junction box
(minimum protection class IP 65) and bridge the distance from the junction box to the computer
with a new shielded cable.

Under no circumstances must you use tape alone to extend the cable.

78 Installing Priva Compass - 00.019

 Outside temperature sensor OTS2

Cable data
Cable type 2
4 x 0.8 mm (0.5 mm ) shielded
Maximum cable length 100 m

Via Meteorological station interface WI2

Connect the sensor via the Meteorological station interface WI2 to a universal input. See also
Connecting sensors to the Weather interface WI2 (page 57).

Mounting
1. Unscrew the two socket head screws (including clamping rings) on the underside of the Outside
temperature sensor completely.
2. Guide the cable through the appropriate opening in the mast.

The Outside temperature sensor has a set position on the mast.

3. Mount the Outside temperature sensor with the two socket head screws (including clamping
rings) on the support of the mast.
4. Feed the cable through the hole in the clamp block assembly so that the cable re-emerges on
the underside of the block.

Cross-section of the Outside temperature sensor

1. Temperature sensor 2. Printed circuit board (9583)

The Outside temperature sensor is supplied with a 10-metre shielded cable. It is

recommended that you do not shorten this cable when mounting the unit. Coil the remaining
length of cable or leave a loop; this will simplify any future expansion of the Meteorological
station with additional crossbars of mast sections.

Outside temperature sensor maintenance

Check the Outside temperature sensor regularly for pollution and clean it if necessary. Pollution can
interfere with the performance of the Outside temperature sensor. Clean the unit with a damp cloth
and a little mild detergent if so required.

Installing Priva Compass - 00.019 79

Priva

Do not use aggressive cleaning and/or abrasives.

Make sure that no moisture, dirt or dust enters the housing when opening the Outside
temperature sensor. This can negatively impact the measurement.

The item 'Temp.sensor 6x60 (glass)' (Part number 111070) is available for replacing a defective
sensor.

Specifications

Article description Outside temperature sensor

Article number 3779204
Measuring principle NTC - 3000 Ω/25 °C
Resolution 0,1 °C
Measurement accuracy 0,2 °C, at temperatures between 0 and 40 °C
0,5 °C, at temperature < 0 °C or > 40 °C
Range -40 °C .. +80 °C
Response speed (T63%) 55 s
Protection Discharges 900 V/100 nF

80 Installing Priva Compass - 00.019

 Outside temperature sensor OTS2

Measurement characteristic
R (Ohm) T (°C)
55.8 150.00
62.7 145.00
70.6 140.00
79.7 135.00
90.3 130.00
102.5 125.00
116.6 120.00
145.7 111.63
190.6 102.07
251.4 92.70
327.3 84.22
416.1 76.80
527.6 69.75
665.0 63.10
833.1 56.85
1022.0 51.36
1234.4 46.43
1447.5 42.39
1644.3 39.21
1872.3 36.01
2106.7 33.16
2355.1 30.52
2626.9 27.95
2991.7 24.95
3399.7 22.05
3863.2 19.20
4430.7 16.20
5083.6 13.24
5874.4 10.19
6792.8 7.18
7885.9 4.15
9169.9 1.14
10713.2 -1.90
12521.9 -4.89
14693.4 -7.90
17320.3 -10.93
20438.6 -13.92
24061.2 -16.81
28108.2 -19.51
36760.2 -24.17
51396.4 -29.66
71521.9 -34.89
99925.9 -40.00

Installing Priva Compass - 00.019 81

Priva

Flow sensor

Connecting
The flow sensor records the volume flow through the irrigation water pipe.

Colour Function Connection

Red open collector signal output digital input of Compass
Black power supply 3.3 .. 24 VDC 24 VDC
Metallic ground FG of Compass

82 Installing Priva Compass - 00.019

 Flow sensor

Cleaning the flow sensor

1. Set the unit to maintenance mode (software-wise and pump switch(es) off).
2. Make sure the main irrigation line is pressure-less and, if necessary, empty.
3. Unscrew the flow sensor from the T-piece.
4. Clean the paddle wheel of the flow sensor using a small, soft brush.
5. Apply a little acid-free grease to the rubber O-rings to prevent them from being damaged when
placing the sensor back.
6. Screw the flow sensor back onto the T-piece: you can only do this one way.
7. Fill and bleed the main irrigation line to prevent water hammer.
8. Check that the flow sensor coupling is not leaking.

Technical specifications – flow sensor

Article description Flow sensor GF2536-P0 Flow sensor GF2536-P0 Flow sensor GF2536-P1
(for lines Ø 20 – 110 mm (for lines Ø 20 – 110 mm (for lines Ø 125 – 160 mm
and 2 – 4") and 2 – 4") and 6")
Article number 750470 750470 (short housing) 750465 (long housing)
Measurement principle paddle wheel
Measurement range 0.3 - 3 m/s
Accuracy 1 % (of max. measured value)
Reproducibility 0.5 % (of max. measured value)
IP code IP67
Minimum Reynolds number required 4500
Supply voltage 3.3 - 24 VDC
Output signal 49 Hz per m/s
Maximum current requirement 10 mA
Cable length 7.5 m
Cable type 2-core shielded twisted pair (22 AWG, 0.326 mm²)

Technical specifications - T-piece for flow sensor

The K-factor is dependent on the flow sensor, the line diameter of the T-piece and the insertion
depth. A certificate showing the K-factor is supplied with the flow sensor. If the certificate is missing,
you can look up the K-factor in the tables below.

The maximum speed at which the pulses can be processed depends on the hardware used.

Installing Priva Compass - 00.019 83

Priva

T-pieces - lines with a metric diameter

Article description PVC T-piece for flow sensor GF2536-P0, metric

Article number 750471 750472 750473 750474 750475 750476
Line diameter, external (mm) 20 25 32 40 50 63
(DN15) (DN20) (DN25) (DN32) (DN40) (DN50)
Measuring range (m /hr) at 0.24 .. 2.4
3 0.38 .. 3.8 0.63 .. 6.3 0.98 .. 9.8 1.54 .. 15.4 2.44 .. 24.4
a flow rate of 0.3 .. 3 m/s and
lines of pressure class PN16
K-factor (pulses per litre) 256.9 128.32 78.54 44.98 27.4 15.72
Litre per pulse (1/K) 0.00389 0.00779 0.0127 0.0222 0.0364 0.0636

T-pieces saddle fitting - lines with a metric diameter

Article description Saddle fitting for flow sensor GF2536-P0, metric

Article number 750477 750478 750479
Line diameter, external (mm) 75 90 110
(DN65) (DN80) (DN100)
Measuring range (m /hr) at 3.46 .. 34.6
3 4.90 .. 49.0 7.34 .. 73.4
a flow rate of 0.3 .. 3 m/s and
lines of pressure class PN16
K-factor (pulses per litre) 9.787 7.281 4.806
Litre per pulse (1/K) 0.102 0.137 0.208

Article description Saddle fitting for flow sensor GF2536-P1, metric

Article number 750482 750483 750466 750467
Line diameter, external (mm) 125 140 160 225
(DN115) (DN125) (DN150) (DN200)
Measuring range (m /hr) at 11.3 .. 113
3 14.6 .. 146 10.5 .. 105 33.9 – 339
a flow rate of 0.3 .. 3 m/s and
lines of pressure class PN16
K-factor (pulses per litre) 4.317 3.446 2.60 1.14
Litre per pulse (1/K) 0.231 0.290 0.385 0.877

T-pieces - lines with an imperial diameter

Article description T-piece GF for flow sensor GF2536-P0, imperial

Article number 750781 750782 750783
Line diameter, internal (") 2.5 3 4
Measuring range (m /hr) at 3.42 .. 34.2
3 4.93 .. 49.3 8.76 .. 87.6
a flow rate of 0.3 .. 3 m/s and
lines of pressure class
comparable with PN16
K-factor (pulses per litre) 11.359 7.04 3.964
Litre per pulse (1/K) 0.088 0.142 0.252

Article description T-piece GF for flow sensor GF2536-P1, imperial

Article number 750784
Line diameter, internal (") 6
Measuring range (m /hr) at 19.7 .. 197
3

a flow rate of 0.3 .. 3 m/s and

lines of pressure class
comparable with PN16
K-factor (pulses per litre) 2.199
Litre per pulse (1/K) 0.455

84 Installing Priva Compass - 00.019

 Flow sensor

For different configurations, a K-factor calculator is available at www.gfsignet.com.

Installing Priva Compass - 00.019 85

Priva

pH interface

Connecting the pH interface

The installation and maintenance of the pH sensor is described in detail in the pH sensor
manual.

1. Connect the BNC connector of the pH sensor to the BNC connector of the pH interface.
2. Unscrew and open the pH interface.
3. Feed the cabling through the cable gland.
4. Connect the wiring of the universal input of the Priva Blue ID module and the power supply to
the connector terminals of the interface. Use a 6-core shielded cable with cores of 6 x 0.8 mm
(0.5 mm²).
5. Screw the interface closed.

Connecting the cable

Name Function Connection
24V 24 VAC FP or 24 VAC from external power supply
0V 0 VAC FG or 0 VAC from external power supply
PH1 sensor signal pH sensor 1 UI
Add a pull-down resistor (100kΩ) to GND for cable
break detection.
GND pH sensor 1 GND (not electrically isolated) FG
PH2 sensor signal pH sensor 2 UI
Add a pull-down resistor (100kΩ) to GND for cable
break detection.
GND pH sensor 2 GND (not electrically isolated) FG

Calibrating the pH interface

Calibrate the pH sensor using the Compass software. See the help text in the software.

Technical specifications - pH-interface

Article description pH-interface

Article number 3771056
Housing material aluminium
Dimensions H x L x W (without grommet) 85 x 120 x 120 mm
Connections on housing:
• 2 BNC-connectors for 2 pH-sensors (3770946)
on pH-interface board 9969:
• 24 VAC input power supply
• 2 analog outputs

Supply voltage 24 VAC

Ambient temperature 0 … 35 °C

86 Installing Priva Compass - 00.019

 pH interface

Technical specifications – pH sensor

Article description pH sensor (max. 10.0 bar)

Article number 3779046
Housing glass
Length of sensor 77 mm
Diameter of sensor Ø 12 mm (Ø 15 mm with protective cover)
Measurement principle +
pH electrode for H ions
Discrimination 59 mV/pH (in operating range 4 .. 7 pH at 25 ˚C)
Operating range (measured values satisfy 4 .. 7 pH
the specified accuracy)
Range (sensor produces measured values) 3 .. 14 pH
Accuracy (after calibration) ± 0.1 pH (in operating range 4 .. 7 pH at 5 .. 30 ˚C)
Cable coax, Ø 2.5 mm, length 3 m
Connector BNC

Installing Priva Compass - 00.019 87

Priva

Dosing Channel Driver

Operation of Dosing Channel Driver

The Dosing Channel Driver can function as a Converter for analogue inputs or as a Repeater for
digital inputs.

For analog inputs, the Dosing Channel Driver converts from a 0 … 10 V input signal to a 24 VAC TRIAC
output signal for dosing channels. This makes it possible to connect and control 5 dosage valves of
dosage channels. The interface has 5 analogue inputs and an enable input for starting a dosing cycle.
The analog inputs of the Dosing Channel Driver are used for Compass.

The Dosing Channel Driver supports dosing channels with the following dosage valves.

Type of dosage valve Article number

Gevasol 24 VAC / 50Hz / 8W 750446
Gevasol 24 VAC / 60Hz / 8W 750545
Buschjöst 24 VAC 50-60Hz 1/4"-3mm 750468

For digital inputs, the Dosing Channel Driver enhances the digital input signals. The digital inputs of
the Dosing Channel Driver are used for Connext.

The application is selected with a jumper. In addition to a connector for the power supply, each
application has its own connector.

A: connecting terminals for 24 VAC power supply (CN2)

B: connecting terminals for 24 VAC TRIAC output signals (CN7-9)
C: connecting terminals for digital inputs (CN4)
D: selection jumper analog (converter) - digital (repeater) (J1)
E: connecting terminals for enable dosing cycle (CN5)
F: connecting terminals for analogue inputs (CN1)

Jumper setting Application

Jumper open analog inputs for Compass (converter)
Jumper closed digital input for Connext (repeater)

88 Installing Priva Compass - 00.019

 Dosing Channel Driver

Connecting the Dosing Channel Driver

Position the Dosing Channel Driver close to the dosing channel. The cable from the TRIAC output of
the Dosing Channel Driver to the valve of the dosing channel may be no more than 10 metres long.

1. Use jumper J1 to set the interface for analogue inputs (Converter) for Compass. The jumper
must be open for the use of analogue inputs for Compass.
2. Connect the power supply to the connecting terminals (CN2) of the Dosing Channel Driver. Use
a 2-core shielded cable with cores of 1.4 mm (1.5 mm²).
3. Connect the wiring of the analogue output of the Priva Blue ID module to the connector terminals
(CN1) of the Dosing Channel Driver. Use a 6-core non-shielded cable with cores of 0.8 mm (0.5
mm²). The maximum cable length is 100 metres.
4. Connect the wiring to the 24 VAC TRIACs for the dosing channels to the connecting terminals
(CN7-9) of the Dosing Channel Driver. Use a 2-core non-shielded cable with cores of 0.75 mm.
The maximum cable length is 10 metres.
5. Connect the wiring of the relay output of the Priva Blue ID module to the Enable connector
terminals (CN5) of the interface. Use a 2-core non-shielded cable with cores of 0.8 mm (0.5 mm²).
The maximum cable length is 100 metres.

Installing Priva Compass - 00.019 89

Priva

The use of 5 dosing channels with GevaSol valves requires at least 100VA. Therefor the
graphic above includes a 300VA transformer. The 24 VAC transformer from the Compass
cabinet can be used, but this means there is no output power available for other components.

Dosing Channel Driver power supply cable

Name Function Connection
24VAC 24 VAC to 24 VAC of external power supply ¹
0VAC 0 VAC to 0 VAC of external power supply ¹
¹ Use a transformer of at least 24 VAC 100VA; 300VA is desirable.

Cables from Dosing Channel Driver to Compass

Name Function Connection
ENABLE start dosing cycle to relay output (voltage free) of Priva Blue ID
module
AI-1 …AI-5 sensor signal to AO of Priva Blue ID module
GND GND to FG of Priva Blue ID module

Cable from Dosing Channel Driver to dosing channel

Name Function Connection
Valve1 … Valve5 0 VAC to 0 VAC to TRIAC of dosing channel
24VAC1… 24 VAC to 24 VAC to TRIAC of dosing channel
24VAC5

Specifications Dosing Channel Driver

General
Module article description Dosing Channel Driver for Priva dosing channels
Module article number 3770170
Number of outputs 5
Dimensions (XYZ) 130 x 160 x 70 mm (5.1 x 6.3 x 2.8 inch)
Maximum power consumption 1.9 W
Installation clicks onto DIN rail
Housing material PVC V-0 (UL94)
Connector type for power supply and I/O pluggable terminal block
Permitted core cross section area solid:: 0.2 … 2.5 mm² (25 … 14 AWG)
flexible with ferrule connector: 0.2 … 2.5 mm² (25 … 14 AWG)
flexible with double ferrule connector: 0.2 … 1.5 mm² (25 … 16
AWG)
Strip length/connector length (terminal block) solid: 10 mm (0.39 inches)
flexible with ferrule connector: 10 mm (0.39 inches)
flexible with double ferrule connector: 12 mm (0.47 inches)

Digital solid-state outputs (TRIAC)

Switching voltage 0 … 30 VAC
Load current 0 … 2.5 A (RMS)
Overvoltage protection 3.15 AT fuse (per channel)
Protection output protected against overload (not self-restoring)
power supply input protected against overload (self-restoring)
Maximum length of output cable 10 m
Switch type TRIAC
Maximum switching frequency 0.2 Hz
Duty cycle 0.1 … 5 s
Indication • red LEDs for status of outputs
• green flashing LED for status of the module
• green LED for status of the enable input

90 Installing Priva Compass - 00.019

 Dosing Channel Driver

Analogue inputs
Input voltage range 0 … 10 VDC
Minimum input voltage for pulse control 2V
Protection input protected against overvoltage up to 30 VDC and 30 VAC
Maximum length of input cable 100 m
Minimum core cross section 0.5 mm² (0.8 mm)

Digital inputs
Input voltage range 0 … 24 VAC
0 … 24 VDC
Protection input protected against overvoltage up to 30 VDC and 30 VAC
Maximum length of input cable 100 m
Minimum core cross section 0.75 mm² (1 mm)

Housing
IP code IP20 (IEC 60529)
Flammability class V-0 (UL 94)
Colour jet black (RAL9011)
Type of device open type equipment for:
• indoor use only
• pollution degree 2 environment

Installation and connection

Installation in control panel:
• accessible to authorised personnel only
• can be clicked onto horizontally or vertically positioned DIN
rail.

Type of DIN rail 35 x 7.5 (1.38 x 0.30 inches) or 35 x 15 mm (1.38 x 0.59 inches)
(height x depth), in accordance with IEC 60715

Environment
Permitted temperature inside control panel of a 0 … 50 ºC (32 … 122 °F)
working system
Permitted temperature during transport and -20 … 70 ºC (-4 … 158 °F)
storage
Permitted ambient relative humidity 10 % … 95 % (niet-condenserend)
Shock and vibration resistance IEC 61131-2
Installation category II

Legislation and standards

Europe • Low Voltage Directive 2006/95/EC:
• EN 61010-1 (measurement and control equipment)
• EN 61010-2-201 (measurement and control equipment)
• EMC Directive 2004/108/EC:
• EN 61326-1 (measurement and control equipment)
• EN 61000-6-2 (generic immunity standard)
• EN 61000-6-3 (generic emission standard)
• RoHS directive 2011/65/EU

Installing Priva Compass - 00.019 91

Priva

EC-DSS interface

Operation of EC-DSS interface

The EC-DSS interface allows you to connect EC sensors or drain sensor systems (DSS). You can
connect two EC sensors or drain sensor systems to one EC-DSS interface. The EC-DSS interface can
be expanded with a second EC interface board 8658 and connection board 9943 to enable you to
connect two more EC sensors or drain sensor systems.

Connecting the EC-DSS interface

1. Unscrew and open the interface.
2. Feed the cabling through the cable glands.
3. Connect the wiring of the EC sensor or DSS to the connector terminals of the interface. Use a
4-core shielded cable with cores of 0.34 mm² (diam. 0.64 mm).
4. Connect the wiring of a second EC sensor or DSS to the connector terminals of the interface.
Use a 4-core shielded cable with cores of 0.34 mm² (diam. 0.64 mm).
5. Connect the wiring of a universal input of the Priva Blue ID module to the connector terminals
of the interface. Use a 4-core shielded cable with cores of 0.8 mm (0.5 mm²).
6. Connect the wiring of the power supply to the connector terminals of the interface. Use a 2-core
shielded cable with cores of 0.8 mm (0.5 mm²).
7. Screw the interface closed.

EC cable to EC-DSS interface

EC cable EC-DSS interface
Core colour Measuring cell 1 Measuring cell 2
White 6 (EC) 3 (EC)
Yellow 5 (Common) 2 (Common)
Grey Do not connect Do not connect
Green 4 (Temperature) 1 (Temperature)
Brown 5 (Common) 2 (Common)

92 Installing Priva Compass - 00.019

 EC-DSS interface

EC-DSS interface cable to Compass

Name Function Connection
MB1 sensor signal sensor 1 UI of Priva Blue ID module
Add a pull-down resistor (100kΩ) to
GND for cable break detection.
GND GND FG of Priva Blue ID module
MB2 sensor signal sensor 2 UI of Priva Blue ID module
Add a pull-down resistor (100kΩ) to
GND for cable break detection.
GND GND FG of Priva Blue ID module
0 VAC 0V 0 VAC of power supply
24 VAC 24 V 24 VAC of power supply

Expanding the EC-DSS interface

1. Unscrew and open the interface.
2. Screw a connection board 9943 to the bottom plate.
3. Insert an EC interface board 8658 into the connector of the connection board 9943.
4. Screw the interface closed.

Technical specifications - EC-DSS-interface

Article description EC-DSS-interface

Article number 3771051
Housing material plastic
Dimensions H x L x W (without grommet) 180 x 165 x 135 mm
Connections on EC-interface board 8658:
• 24 VAC input power supply
• 2 inputs for EC or DSS
• 2 analog outputs

Supply voltage 24 VAC, 50/60 HZ

Ambient temperature 0 … 35 °C

Installing Priva Compass - 00.019 93

Priva

Connecting the Compass EC sensor

Cross section of inline EC sensor

Cross section of angled EC sensor

Connecting the Compass EC sensor

EC sensor EC interface VP9943+VP8658

Core colour Measuring cell 1 Measuring cell 2
White 6 (EC) 3 (EC)
Yellow 5 (Comm.) 2 (Comm.)
Grey Do not connect Do not connect
Green 4 (Temp.) 1 (Temp.)
Brown 5 (Comm.) 2 (Comm.)

1. Connect the EC sensor to the interface with a 4-core shielded cable with cores of 0.34 mm (Ø
2

0.64 mm).
2. It may be possible to extend the cable. Extending the cable will, however, increase the measuring
error (see tables below).

In the case of an EC measurement via single cores, limit the length to 60 m.

3. Connect the shielding on the cable to the earth bar in the housing.
4. Adjust the cell factor with the potentiometer, see Calibrating the EC sensor (Compass) (page 95).

94 Installing Priva Compass - 00.019

 EC-DSS interface

Cable length (2x 0.34 Measuring error at 15 Measuring error at 10 Measuring error at 5 Measuring error at
mm²) mS mS mS 0.1 mS
5m 1% 0.5% 0.3% --
60 m 9% 6% 3% 0.1%
120 m 16% 11% 6% 0.1%

Cable length (4x 0.34 Measuring error at 15 Measuring error at 10 Measuring error at 5 Measuring error at
mm²) mS mS mS 0.1 mS
5m 0.4% 0.3% 0.1% --
60 m 5% 3% 1.5% --
120 m 9% 6% 3% 0.1%

Specifications for EC sensor

Article description Inline EC sensor, short, Inline EC sensor with Angled EC sensor, Angled EC sensor with
with NTC 1 kΩ/25°C NTC and thermistor long, with NTC 1 NTC and thermistor
kΩ/25°C
Article number 3779052 3779043 3779041 3779045
This part is no longer This part is no longer
available. available.
Temperature sensors NTC 1 kΩ/25 °C NTC 1 kΩ/25 °C NTC 1 kΩ/25 °C NTC 1 kΩ/25 °C
Thermistor 3 kΩ/25 °C Thermistor 3 kΩ/25 °C
Spare parts NTC 1k with cable, - NTC 1k with cable, long -
short EC sensor EC sensor (3476074)
(3476073)
Measurement range 0.01 to 15 mS/cm 0.01 to 15 mS/cm
Cell factor 1.23 cm/cm
2
1.82 cm/cm
2

Temperature Necessary approx. 1.8 to 2.2 %/°C Necessary approx. 1.8 to 2.2 %/°C
compensation
Temperature range 0 to 45 °C (when active) 0 to 45 °C (when active)
0 to 65°C (when inactive) 0 to 65°C (when inactive)
Pressure range Maximum 10 bar Maximum 6 bar
Flow speed 3
0.5 to 25 m /hour
3
0.5 to 25 m /hour

Calibrating the EC sensor (Compass)

Have the EC sensor calibrated by a dealer at least once a year. The calibration can be done using a
portable EC meter. Use the portable EC meter to determine the EC value of the water within the
sensor.

A portable reference EC meter is required for calibrating the EC measurement, like Portable
EC and pH analyzer (3779190) or Portable EC analyzer (3779191).

Installing Priva Compass - 00.019 95

Priva

EC Interface VP9943

1. Go to Water Room > Water system > Settings > Stop water system for maintenance and select
IMMEDIATE.
2. Make sure that water with a constant composition is pumped through the EC measuring sensor.
Use the available valves and pumps of the unit, depending on the type of unit and the model.

For a usable calibration the EC value must be within the unit's normal control range, for
instance around 2 mS.

3. Collect some water with fertiliser and measure its EC value using a reference EC meter.
4. Calculate the desired output signal (in mV) of the EC Interface VP9943: desired output signal=EC
value x 500.
5. Connect a digital multimeter to test point TP0 (Gnd) and TP5 (signal EC sensor 1) on EC Interface
VP99433.
6. Adjust the potentiometer R31 until the multimeter shows the desired output signal (calculated
in step 4).
7. Connect a digital multimeter to test point TP0 (Gnd) and TP7 (signal EC sensor 2) on EC Interface
VP99433.
8. Adjust the potentiometer R33 until the multimeter shows the desired output signal (calculated
in step 4).
9. Go to Water Room > Water system > Settings > Stop water system for maintenance and select NO
STOP.
10. Reset the unit valves and pumps to the correct position.

96 Installing Priva Compass - 00.019

 Drain water sensor

Drain water sensor

Use
Drain water is water that is not taken up by the plants and the substrate (for instance mineral wool,
coco peat or Perlite). This excess of irrigation water is necessary to prevent the substrate from
becoming excessively saline as a result of the accumulation of fertilisers.

The Priva Drain water sensor accurately measures the electrical conductivity (EC value) of the drain
water and the quantity of drain water from the substrate. The Drain water sensor is connected to
the process computer.

EC measurement
The EC value is an indicator of the fertiliser-water ratio in the drain water: a high EC value points to
a high concentration of fertilisers, while a low EC value points to a low concentration of fertilisers.
The chemical composition of the drain water is determined by the selective uptake of the fertiliser
elements by the plant roots.

The desired EC value of the irrigation water depends on the crop, the substrate and the composition
of the fertilisers.
The EC sensor is located in the flow tube underneath the Drain water sensor. This tube is a trap
construction, so that drain water is always present in the EC sensor.

Quantity measurement
Based on the quantity measurement of the Drain water sensor, the optimum strategy for supplying
irrigation water is determined.

The drain water derived from the substrate is collected in a drain trough (available separately). At
the end of the drain trough, the drain water flows into the tray of the Drain water sensor. The water
then flows, via a dirt filter, into the flow tube underneath the Drain water sensor.

At the end of the tube, the drain water is collected drop by drop on the tipping ladle. When the ladle
is full, it tilts downwards, thus activating a reed relay. The number of times that the tipping ladle tilts
over is a measure of the quantity of drain water.

The Drain water sensor has a maximum measuring capacity of 3.6 litres per hour.

If the Drain water sensor is processing 3.6 litres per hour, the tipping ladle is continuously
active. This is not a desirable situation. There must be a period between two irrigation cycles
in which the tipping ladle is not active, otherwise the cycles run into each other and it is not
possible to correctly measure the quantity per irrigation cycle.

Installing Priva Compass - 00.019 97

Priva

Overview

Overview of the Drain water sensor

A. Drain trough
B. Substrate slab
C. Tray
D. Dirt filter
E. Water level in the flow tube when drain water has drained away
F. Flow tube/trap
G. Temperature sensor (NTC 1 kΩ/25°C or thermistor 3 kΩ/25°C) and EC sensor (moulded-in)
H. Outflow cap with opening diam. 1.5 mm
J. Tipping ladle
K. Reed relay contact
L. Magnet (counterweight of tipping ladle)
M. Junction box

Mounting the Drain water sensor

If the Drain water sensor is used for a crop in the soil, the Drain water sensor is buried in
the soil.
The Drain water sensor must not stand in water, as this may cause corrosion. For that reason,
bear in mind the following:
• The drain water should be able to drain away into the ground. With loam and clay in
particular, this can be a problem.
If necessary, ensure that the drain water drains away correctly.
• The groundwater level should not be too high.

Also make sure that the Drain water sensor is well ventilated, so that dirt cannot accumulate.
If the Drain water sensor is placed in an enclosed space below ground level, its service life
is reduced considerably.

98 Installing Priva Compass - 00.019

 Drain water sensor

1. Install the trough in such a way that the drain water can easily flow into the tray of the Drain
water sensor. The trough must have a slope of around 1%.
2. Hang the Drain water sensor at the end of the trough.

In the case of slab weighing, do not hang the Drain water sensor at the end of the trough,
but in a different place. If the Drain water sensor is suspended at the end of the trough,
the drain will also be included, which will disrupt the measurement.

3. Cover the substrate slab, the trough and the Drain water sensor with foil, to prevent dirt and
algae growth in the Drain water sensor.

Installing Priva Compass - 00.019 99

Priva

Connecting the Drain water sensor (Compass)

Connect the Drain water sensor to:
• EC interface board VP9943 (via connection board VP8658)
• Compass C4

Connection diagram for Drain water sensor with NTC 1 kΩ/25°C

Connection in junction box Connection to

EC interface board VP9943 (via connection board VP8658)
1 White (EC+ / excitation+) 3 (EC) or 6 (EC)
2 Green (EC- / excitation-) 2 (EC Comm) 5 (EC Comm)
3 Yellow (NTC/Thermistor wire 1) 2 (Temp Comm) 5 (Temp Comm)
4 Brown (NTC/Thermistor wire 2) 1 (Temp) 4 (Temp)
Compass C4
5 Black (Reed relay wire 1) DI
6 Black (Reed relay wire 2) FG

You must connect the green and yellow core of the Drain water sensor jointly to Common
(terminal 2 or terminal 5) of EC interface board VP9943.

Cable specifications

Cable type 2
6 x 0.64 mm (0.34 mm ) shielded
Maximum cable length 60 m

After installation, you must calibrate the Drain water sensor.

100 Installing Priva Compass - 00.019

 Drain water sensor

Specifications of the Drain water sensor 1 kΩ

Drain water sensor

Article description Drain sensor system DSS with NTC 1 kΩ/25°C

Article number 3779224
To connect to Spectra 92 and CD/I
C line
Compass
Temperature sensor NTC 1 kΩ/25 °C
Measurement range 0.01 to 15 mS/cm
Cell factor 5.0 cm/cm
2

Temperature compensation Necessary approx. 1.8 to 2.2 %/°C

Temperature range 0 to 45 °C (when active)
0 to 65°C (when inactive)
Maximum measuring capacity 3.6 litres/hour (tipping ladle is continuously loaded)

Dimensions of the Drain water sensor

Drain trough

Article description Drain trough 200 cm Drain trough 280 cm

Article number 3475021 3475022
Dimensions (LxW) 200 x 20 cm 280 x 20 cm
Material Stainless steel

Dimensions of Drain trough

Installing Priva Compass - 00.019 101

Priva

Groscale

Priva Groscale allows you to accurately follow the fluctuation in the slab weight and thus the amount
of water present in the substrate slab. This will give you an insight into the amount of water absorbed
by your plants in the course of the day. When the right software is installed on the process computer,
this will give you an extra set of tools to regulate and keep an eye on the water dosage, as well as
to protect your plants from being deprived of water as a result of substrate slabs becoming too dry.
You can avoid loss of production and even achieve an increase in production by simply reacting
correctly to the amount of water present in the slabs.

The Groscale consists of two or four weighing platforms connected to a weighing indicator. The
weighing platforms are fitted with a sensor which records the measured weight. The weighing
indicator combines the signals of the weighing platforms and converts these into a total weight.
Weight measurements are taken continually by the weighing indicator. The computer will allow you
to request collective measurement values in a table and a diagram. For further information on
viewing and using the measurement values, please refer to your process computer manuals.

The Groscale is developed with a view to highly accurate measurements of substrate slab weights.
Therefore, the device is more accurate than is strictly necessary for the measurement of moisture
content; this makes the system suitable for extension in the future, even if these extensions require
a higher level of accuracy.

102 Installing Priva Compass - 00.019

 Groscale

Layout

1 Weighing platform 2 Paving-stones (30 x 30cm), not part of the delivery

3 Support frame (optional) 4 Connection cables weighing platforms
5 Weighing indicator 6 Control panel
7 Greenhouse post, not part of the delivery 8 Connecting cable to process computer, not part of the delivery
9 Support arm 10 Support lock
11Box position bow (optional)

The Groscale consists of a weighing indicator, two or four weighing platforms, one support frame
for every two weighing platforms and the fitting materials necessary. The two weighing platforms
are connected by means of the support frame. The boxes with substrate slabs can then be placed
on top of this support frame.

The support frame has an adjustable length and width in order to make it suitable for a variety of
box dimensions. When no subsurface boxes are used, a plate can be placed on the support frame
as a support for the slabs. The support frame can be left out if using a drain tray which is rigid enough
not to bend. Measures have to be taken to prevent moving or dragging of the drain tray. This will
influence the measurement.

This can be accomplished by using box position bows, which positions self carrying drain trays up
to 21 cm width.

It would be a good idea to put the substrate slabs on a slight lengthways slant, since this would
encourage drainage.

When using additional materials to support the substrate slabs, it is important not to use wood or
other materials which absorb moisture. This would affect the weights measured.

Installing Priva Compass - 00.019 103

Priva

Preparing for installation

Determining the location for weighing platforms and weighing indicator

It is desirable to set up the Groscale at the location before the start of a new crop. However, it is
possible to set up the weighing platforms in an existing situation.

First and foremost, you need to determine the location where you want to take the weighings. This
location should be a representative spot in the middle of the crop. When using an unit with four
weighing platforms (2 x 2 weighing platforms), one unit should be placed on the left and the other
on the right of the row of crops in the same section. This way an average value is obtained for the
slab weight of plants on the sunny and the shadowy side of the row of crops are taken into account.
This is because of differences in transpiration. With a V-system, the weighing platforms can be placed
one after the other and the weighing indicator in the middle.

When determining location, the following conditions should also be met:

• The total weight resting on top of the weighing platforms from the support frame, the drain
troughs, subsurface boxes, plants and saturated slabs may not exceed the capacity of the
weighing unit. This is 100 kg (2 weighing platforms 50 kg), 200 kg (2 weighing platforms 100 kg
or 400 kg (4 weighing platforms 100 kg).
• Preferably, the weighing unit should be placed in the valve section which also contains a box to
measure drainage. Dosage and drain measurement can be compared, which gives a surplus
value because the effect on the moisture content can be determined.
• Every weighing platform has a maximum cable length of 5 metres. Therefore, you should bear
in mind that the maximum distance between weighing platform and weighing indicator cannot
exceed 3.5 metres (1.5 metres will be lost on the distance between soil and weighing indicator).
• Weighing platform should not be placed underneath a gutter, because condensation water could
drip off the gutter onto the slab and because the gutter could overflow after heavy rainfall.
• Place the weighing platforms sufficiently high that they remain dry and no water collects
underneath the weighing platforms. This could damage the electrical parts and cause corrosion
over a long period of time.
• Make sure that the higher part of the weighing platform does not get too close to the tubular
heating system or any other source of heating. The radiated warmth could affect the sensor in
the weighing platform and therefore affect the measurement itself.
• When using CO₂-hoses, you need to make sure that these have no discharge openings at the
location where the weighing platform is installed. The waste gases will warm the sensor in the
weighing platform and affect the measurement.
• Preferably, do not suspend CO₂-hoses over the weighing unit, since condensation drops could
fall onto the slab.
• Slab heating should be led around the weighing unit so that it is not accidentally included in
measurements. Due to the way the weighing unit is installed, the slabs do not lie on the cold
floor; therefore slab heating will be superfluous in most cases.
• Please decide whether you want to set up your substrate slabs on the same level with your other
slabs or whether a difference in height is acceptable (maximum 15 cm difference). When using
a countersunk configuration for the weighing platforms, it is necessary to ensure good drainage.
In addition, it is necessary to dig a groove in between the two weighing platforms, for the support
frame and/or the subsurface box.

Configuration of substrate slabs

Below you will find a number of examples of substrate slabs and an indication of the weight of an
unit with a saturated slab.

Possible layouts for slabs 2 x (133x20x7.5 cm) weight saturated slab

Rigid boxes which are placed directly onto the weighing platforms without support 41 kg
frame with box position bow.
Boxes which are placed on a drain trough on top of the weighing platforms without 48 kg
support frame with box position bow.
Boxes placed on top of specially developed support frames. 55 kg

104 Installing Priva Compass - 00.019

 Groscale

Materials required
A 4 x twisted pair of shielded cables should be laid between the process computer and the weighing
indicator, with the following specifications:
• 8 core, twisted pair, fully shielded
• Core area 0.5 mm
2

• Cable diameter 8 mm (this is necessary for a correct fit when feeding it through the grommet
supplied with the weighing indicator).

Out of these, 4 cores (4 pairs) will be used for the power supply and 2 cores (2 pairs) will be used for
the output signals of the weighing indicator. The weighing indicator will be supplied by a supply
voltage of 24VAC or 24VDC coming from the process computer. Use a fused supply voltage for this.

The weighing indicator contains two analog outputs which are used to pass the weight shown on
the display to the process computer. Either one or two analog inputs are used, depending on the
type of process computer being used and the software version running. With modern computer
systems, it would be advisable to connect both outputs to a 0 - 5V analog input, with a view to future
software operation. In this case, both analog inputs should be used on the same IO-board. On older
computers, only the first analog output can be connected.

A double core pair can be used to bridge the distance to the weighing indicator, depending on
whether the supply voltage is AC or DC. Use a separate cable for each weighing indicator.

Power supply Maximum cable length

24VAC 800 m
24VDC 1600 m

Installation

Installing weighing platforms

Layout for support frame, dimensions in mm

1. Determine the distance between the weighing platforms. If you are using the weighing support
frame, position the platforms with a centre-to-centre distance equal to the length of your weighing
system minus 60 cm. (For instance: with two 100 cm tanks plus a distance between them of 20
cm, the platforms should be positioned with a centre to centre distance of 220 - 60 = 160 cm
apart). If the weighing support frame is not being used, it is best to position the platforms at a
quarter of the total distance from both ends of the weighing system.
2. Determine whether the weighing platforms should be installed in a recessed manner, so that
the substrate slabs are flush with the other slabs. In this case, it must be guaranteed that the
weighing platforms will remain dry. Make sure therefore that there is good drainage and pay
attention to the maximum groundwater levels that may occur.
3. Excavate at least 5 cm of soil below the foundations of the weighing platforms for a bed of sand.
If the weighing platforms are to be installed in a recessed manner, the soil below the weighing
support frame must also be removed, so that the weighing frame is suspended entirely freely.
In the case of a recessed arrangement, it is advisable to use a bed of sand of at least 30 cm in
order to ensure good drainage and, in addition, to apply a casing around the weighing platform
to prevent the excavation from collapsing.
4. Spread white sand in the excavated soil, and place the paving slabs on top.
5. Level the paving slabs and tap them with a rubber hammer. There may be a small difference in
height between the various paving slabs, to provide a slope.

Installing Priva Compass - 00.019 105

Priva

6. Place the weighing platforms in their correct position. Make sure that the supporting side of the
weighing platform, the upper part, is turned away from the pipe rail. This is because the radiant
heat of the rail can influence the measurement.
7. With the aid of the three adjustable posts, level the weighing platforms on the paving slabs (a
spirit level is included on the platform).

Do not turn the bolt that protects the load cell from overload (see illustration). In the
unladen state, there must be a distance of 6 mm between the underlay and the bolt.
If the distance is too great, the load cell will be insufficiently protected; if the distance
is too small, the measurement range will be incomplete.

8. Adjust the weighing support frame to the correct length and width (see figure: “dimensions for
setting up the weighing support frame”). Place the substrate tanks on the weighing support
frame (see Configuration of substrate slabs (page 104)).
9. If you are using a self-supporting drain tray of up to 21 cm in width with supplied brackets, place
the brackets in which the tank is located on the arm of the weighing platforms in accordance
with the figure below.

Placing box position bow for drain tray up to 21 cm width

Positioning of weighing indicator

The weighing indicator should be fitted on the greenhouse post at a distance less than 3.5 metres
away from the location where the weighing platform are to installed. Use the support arm and the

106 Installing Priva Compass - 00.019

 Groscale

support lock. The support plate onto which the weighing indicator is mounted is then slid onto the
support arm and bolted using the wing nut. Proceed as follows:
1. Fit the support lock, the support arm and the weighing indicator in such a manner that they do
not interfere with any existing overhead heating. This also applies to any cabling running to the
process computer and weighing platforms. The overhead heating needs to move freely either
in front or behind the unit.
2. Fit the weighing indicator at the correct operating height and check that the connecting cables
of the weighing platforms are sufficiently long.
3. Open up the weighing indicator and let the control panel hang from the earth-wires.
4. Feed the weighing platforms’ connecting cable plugs around the back of the control panel and
plug them into connectors L1-L4. The sequence does not matter.

Make sure you place the plugs correctly when plugging them into the connectors and
that all pins are rightly inserted.

5. Push the connecting cable grommet into the holes in the edge of the housing.
6. Roll up excess lengths of cable and hang these onto the side of the weighing indicator.

Never shorten the cables of weighing platforms!

Connecting Groscale to Compass

Terminal C1 Name Function Twisted Pair Compass connector

1 0VAC or 0VDC Power supply 1+2 - of a 24 VDC power supply
2 24VAC or 24VDC Power supply 1+2 + of a 24 VDC power supply
3 DAC1gnd GND 1st analogue output 3 UI
4 DAC1OUT Signal 1st analogue output 3 FG
5 DAC2gnd GND 2nd analogue output 4 UI
6 DAC2OUT Signal (fine) 2nd analogue 4 FG
output
7 Shield Cable shielding Shield Compass ground busbar

1. Unscrew the weighing indicator to open it and allow the operating panel to hang from the ground
wires.
2. On account of the removal of the weighing indicator during crop change, do not feed the
connecting cable to the process computer through the tube. Also remove this from behind the
operating panel, as well as the connecting cables of the weighing platforms. Position the supplied
grommet over the cable. This is absolutely necessary in order to achieve a watertight sealing of
the housing.
3. Connect the cores of the twisted pairs to the supplied plug in accordance with the table above.
4. Use two pairs per terminal for the power supply.
5. On the process computer side, the shielding of the connecting cable is connected to the earth
strap.
6. Fit the plug cap, slide the grommet to the correct length, fit a hose clip as strain relief and press
the grommet into the appropriate hole in the housing.
7. Feed the cabling through the cable glands.
8. Close the weighing indicator by screwing it tight.

Make sure that the 24VAC/24VDC and 0VAC/0VDC are electrically isolated from the DAC1gnd
and DAC2gnd. With the twisted pair, it can easily be mixed up, which leads to errors. Be sure
to check this again!

Installing Priva Compass - 00.019 107

Priva

Commissioning

Commissioning for the first time

1. Check that the unit is working (see Checking operation of the weighing indicator (page 108))
2. Enter the data for the load cells (see Setting the load cell data (to be performed by the service
engineer only) (page 108))
3. Follow the calibration procedure, see Calibrating slab (weight of dry and saturated slab) (page
109).

Checking operation of the weighing indicator

Check the status of the LEDs in the housing. The three green LEDs with the text V24ac, Vcc and V18+
must light up brightly. The yellow LED with the text T1 must flash after the weighing indicator has
started up. Go to the chapter "Fault diagnosis" if the weighing indicator does not work after it has
been connected.

Setting the load cell data (to be performed by the service engineer only)
When the slab weigher is taken into use, the specific data for the load cells in the weighing platforms
must be entered in the weighing indicator. You can do this in the Load cells menu. The numbers for
Sensitivity and Zero point appear on the cables in the weighing indicator.

1. Open the weighing indicator and let the cover with the display hang down.
2. Go to the menu Load Cells .
3. Deactivate the menu protection by pressing “Enter” followed by “ ↑ ” and hold this key combination
down for 3 seconds. <<MENU>> will change to >>MENU<<.
4. Activate the menu by pressing “Enter”. The display will show Sensitivity 1 .
5. Press “Enter” to enter the sensitivity of load cell 1.
6. Enter the sensitivity by using the arrow keys. This figure can be found on the weighing platform
cable. The value of the setting changes more quickly if either of the arrow keys is pressed down
continuously.
7. Press “Enter” to confirm the value you just set.
8. Press “ ↓ ”.
9. The display will now show Zero 1 ; press “Enter” if this is to be adjusted.
10. Enter the zero by using the arrow keys. This figure can be found on the weighing platform cable.
11. Press “ ↓ ” and enter the sensitivity for load cell 2 and the zero for load cell 2.
12. Then enter the zero for load cell 2. Enter the data for load cells 3 and 4, if present.
13. After pressing “ ↓ ” following the entry of Zero 4 for load cell 4, the display will show # of Load
Cells .
14. Press “Enter”; this enables you to enter the number of load cells.
15. Enter the number of load cells (2 or 2) using the arrow keys and press “Enter” to confirm if this
value differs from the default value (which is set to 4).
16. Press “ ↓ ”: the display will now show #kg/Load Cell .
17. Press “Enter” if the weight range of the load cells is to be changed.
18. Press “ ↓ ”. The display will now show Set tare Weight ; here the new zero weight should be
recorded. The display shows the current nett weight surrounded by << >> brackets. Pressing
“Enter” will change the brackets so they are turned inwards, i.e. >> <<. Press “Enter” again in
order to record the new zero weight. The display will now show <<000,000>>. Press “Esc” if the
current nett weight is not to be adjusted. The same can be done with the menu Slab calibration
(please refer to the chapter “Operation and display”). This function can be used to check the
weighing unit using a small calibration weight (1 kg). Perform the Set tare Weight function and
place the calibration weight on the unit. Check the display to see if the correct weight is shown,
while keeping in mind the measuring accuracy of the weighing unit as a whole.
19. Press “ ↓ ” if you wish to rectify small deviations caused by installing the weighing unit. However,
it is not mandatory to perform this function.
20. The display will show Adjust Sens. It is assumed that the weighing unit has been tared. Place a
20 kg calibration weight at the height of each of the weighing platforms. The left of the display
will show the nett weight. If this is incorrect it can be adjusted by pressing “Enter” and using the
arrow keys until the actual nett weight on the left of the display shows a value which equals the
total weight of all calibration weights. Press “Enter” to confirm.
21. Press “Esc” to leave the menu and reactivate the menu protection.

108 Installing Priva Compass - 00.019

 Groscale

Calibrating slab (weight of dry and saturated slab)

In order to register the most accurate weight in the process computer, it is necessary to match the
output range of the analog output as closely as possible to the maximum nett weight to be weighed.
For this, the dry weight and the weight of the saturated substrate slab should be recorded after
which the output range can be set in the menu Service, menu item Max #kg/5V on the basis of the
saturated slab weight. This can be entered by using the menu Slab calibration .

If a weighing platform carries a dry substrate slab witdry plant pots, the weighing unit can be tared.
The following procedure should be performed:
1. If necessary, put the empty subsurface box(es) on a drain trough or a support frame. Add the
dry slab and place the dry plant pots on the weighing platforms.
2. Go to the Slab calibration menu.
3. Deactivate the menu protection by pressing “Enter” followed by “ ↑ ” and hold this key combination
down for 3 seconds. <<MENU>> will change to >>MENU<<.
4. Press “Enter” to activate the menu.
5. The display now shows Set tare Weight and it shows the current nett weight. Press “Enter” to
indicate that the Set tare Weight function is to be performed. The brackets on either side of the
weight will change direction to >> <<. Press “Enter” again to set the measured value to zero.
6. Press “Esc” to leave the menu and to reactivate the menu protection.
7. Saturate the slab fully. Place the plant pots - which have been moistened as well - onto the slab.
The slab should not be allowed to drain. If the slab is not fully saturated you should proceed
with this setting procedure and adjust the range at a later date by means of the Service menu
(Please refer to “Setting output range and adjusting slab calibration data at a later date”).
8. Go to the Slab calibration menu.
9. Deactivate the menu protection by pressing “Enter” followed by “ ↑ ” and hold this key combination
down for 3 seconds. <<MENU>> will change to >>MENU<<.
10. Press “Enter” to activate the menu.
11. Press the “↓” key once.
12. The display will now show the text Saturated Slab and it shows the current nett weight. Press
“Enter” to indicate whether you want to adjust the setting. The brackets surrounding the displayed
weight will change direction to >> <<. Press “Enter” again to record the displayed weight in the
weighing indicator.
13. Press “Esc” to leave the menu and reactivate the menu protection.

In order to calibrate the unit in one day, moisture should be dripped onto the slab until this
is saturated and a number of similar slabs and subsurface boxes should be kept aside for
taring purposes.

Setting output range and adjusting slab calibration data at a later date
If you have not used the dry or saturated slab for calibration purposes during the calibration process,
you will still be able to enter the weight of an empty or full slab (or an estimate of these) manually
by using the Service menu. The output range of the analog output 1 to the process computer can
also be set here.

1. Go to the Service menu.

2. Deactivate the menu protection by pressing “Enter” followed by “ ↑ ” and hold this key combination
down for 3 seconds. <<MENU>> will change to >>MENU<<.
3. Press “Enter” to activate the menu.
4. The display will show the text Set tare Weight . Press “Enter” if this weight is to be adjusted. Here
the weight of an empty unit has to be entered. This will usually equal the weight of the support
frame including substrate slabs and subsurface boxes. This weight will be used as the new zero
weight in relation to the absolute zero point of the weighing indicator.
5. Use the arrow keys to set the weight of a dry slab and press “Enter” to confirm.
6. Press the “ ↓” key.
7. The display will now show the text Saturated Slab . Press “Enter” if this weight is to be adjusted.
8. Set the weight of the saturated slab using the arrow keys and press “Enter” to confirm.
9. Press the “ ↓” key.

Installing Priva Compass - 00.019 109

Priva

10. The display will now show the text Max #kg/5V . This is the maximum number of kg nett weight
that the analog outputs can pass to the process computer. This maximum nett weight must be
derived from the saturated slab weight. Keep a safety margin for plant weight increase due to
plants which are not fully supported. The weighing indicator will show a 5000 mV output voltage
at this maximum number of kg.
This maximum number of kg should never be exceeded by the nett weight. Therefore it is not
advisable to adjust this figure.
11. Press “Enter”.
12. Set the desired number of kg by means of the arrow keys and press “Enter” to confirm.
13. Press “Esc” to leave the menu and reactivate the menu protection.

Testing outputs signals and cabling (to be performed by service engineer only at first
commissioning)
The weighing indicator has been fitted with a function which gives you the opportunity to check the
cabling from the analog outputs to the process computer, so it can be established whether these
are functioning properly. In reverse phase, both analog outputs will transmit a block wave during
5000 seconds: a high and a low signal of respectively 0 mV and 0 mV. The 5000 mV of the first analog
output equals 30 kg value, the 0 mV will match the Max #kg/5V set value.

If the measuring data are not given correctly by the process computer, this signal can be used to
check whether a signal is transmitted through the cable. The signal can also be used to weaken the
signal for connection to the process computer.

1. Go to the Test Outputs menu.

2. Deactivate the menu protection by pressing “Enter” followed by “ ↑ ” and hold this key combination
down for 3 seconds. <<MENU>> will change to >>MENU<<.
3. Press “Enter” to activate the menu.
4. The display will now show Toggle Outputs; press “Enter”.
5. Press “↑” and “Enter” to set the setting to 1. Now a 30 second signal will be controlled to the
process computer, first 0 mV followed by 5000 mV. During this signal, the analog outputs are
controlled in reverse phase, i.e. output 1 will be 0 mV and output 2 will be 5000 mV followed by
a 30 second signal in reversed order.
6. Perform the desired calibration or check with the 0 mV and 5000 mV signals. Wait 30 seconds
for the next signal to be given. LED T2 will now give four flashing signals.
7. Go to the weighing indicator and change the setting Toggle Outputs from 1 to 0 by pressing “Enter”
and “ ↑ ”, followed by “Enter” again.
8. Press “Esc” to leave the menu and reactivate the menu protection.

Recording essential data

The calibration data will be lost if there is a defect in your weighing indicator. The Service menu can
be used to re-enter the old calibration values, immediately after the weighing indicator has returned
after being repaired. Using the known Service menu can data for the weighing platforms and the
number of platforms, the Groscale can be started up again without re-calibrating a dry and a saturated
slab . (for this is not possible during growing since the weighing platforms are already loaded with
substrate slabs)

It is highly recommended to copy the calibration data on the form found in the weighing indicator.n
When you have calibrated the slab, you should go to the Measurements menu using the arrow keys.
From this menu you need to get the values Tare Weight, Saturated Slab and Max #kg/5V and enter
them on the form which accompanies the weighing indicator. These values should be recorded after
every calibration (which is usually once every growing season).

The form should be returned to its little bracket behind the weighing indicator.

Placing plants on the slab

You can now place the plants on the substrate slabs. When weighing the water in the slab you should
prevent the weight of the plants themselves from being weighed as well. The way you do this depends
on the type of crop. Plants which are suspended from wire can be supported. For other crops,
another solution will have to be found or you will have to accept the weight of the plant as being
part of the weighing result.

110 Installing Priva Compass - 00.019

 Groscale

At the start, young plants can distort the measurement results, since their weight will not yet be
supported by any wire. You should take this continuously increasing weight into consideration when
viewing and analysing the measurement results.

Supporting plants suspended from wire

When the plants you want to suspend from wire are big enough, you can support both the plants
and the wire itself by braces which are available from a variety of suppliers. During the growing
season, it would be advisable to check the plants and the bracing at least once a week to give you
the opportunity to replace and adjust the bracing if necessary. This means that plants could possibly
more or less rest on the substrate slab. As a result of this, there will be a change in the measurement
results. In order to counteract this, the nett weight can be changed accordingly. However, after
changing the calibration point a few times, the measuring results will no longer be accurate. Therefore
an adjustment should be considered when reading the measurement data in your process computer.

If you might still want to change the nett weight, proceed with the following but only in a period
when there is no water dosage:
1. Write down the weight shown on the display.
2. Rehang the plants and move the braces.
3. Determine the difference between the old and the new weight shown on the display and if this
is the case, follow the procedures outlined below.
4. Go to the Adj. Nett Weight.
5. Deactivate the menu protection by pressing “Enter” followed by “ ↑ ” and hold this key combination
down for 3 seconds. <<MENU>> will change to >>MENU<<.
6. Press “Enter” to activate the menu.
7. Change the current Nett Weight with the old value by using the arrow keys and finally confirm
this weight by pressing “Enter”.
8. Press “Esc” to leave the menu and reactivate the menu protection.

LEDs

number/colour of LED text with LED meaning

1/green V24ac input voltage of weighing indicator
2/green VCC supply voltage digital part
3/green V18+ supply voltage analogue part
4/yellow T1 processor activity
(it should flash, at irregular intervals)
5/yellow T2 • continuously off: system OK
• continuously on: system OK, the
production jumper has been installed.
• 1x flashing signal: the display is not
responding
• 2x flashing signal: no ADC interrupt
• 4x flashing signal: the Test outputs menu
is still active.
The number of flashing signals is added
together. Thus: 6 flashing signals means: ADC
is defective, and the operating mode for
testing the outputs is still active.
6/red RST power supply monitor/watchdog

Operation and display

Operation
The keys on the weighing indicator control panel have the following functions:

Installing Priva Compass - 00.019 111

Priva

key showing on display result

↓ Menu shows following menu
value/setting shows following value/setting
setting to be changed shows following setting value
↑ Menu shows previous menu
value/setting shows previous value/setting
setting to be changed shows previous setting value
Enter Menu shows value/setting
value setting makes change to setting
setting to be changed confirms value set
Esc Menu shows software version number
value/setting shows menu
setting to be changed stops change to setting without saving

In order to prevent anyone from accidentally changing settings, all menus with the exception of
Measurements and Display are protected. This protection can be removed by first selecting the “Enter”
key, followed by the “ ↑” key and holding this key combination for a minimum of 3 seconds. When
protection is removed, the double brackets surrounding <<MENU>> will change to >>MENU<<. When
this has changed, the menu can be activated by pressing the “Enter” key.

Protection is automatically re-activated after 15 minutes. However, it can be re-activated manually

by “Esc” ; the name of the menu will then be shown normally again.

Examples of operation

When the weighing indicator display is not in use, the Nett weight is shown.

This is the actual weight of the water in the substrate slabs. By entering the “ ↓ ” key , the
following setting is displayed: # of Load Cells . You will now be shown how the Groscale has
been calibrated.

By pressing “ ↓ ” when the display shows Nett weight , the following items are shown respectively:
• Nett weight (is updated 3 times per second)
• # of Load Cells (# represents number of cells)
• Tare Weight
• Saturated Slab
• Max #kg/5V

Examples of settings changes

In the Display menu, the display contrast can be set as well as the language in which the settings
should be shown. Please note that the values are still in Dutch decimal numbers. The menu
appears when “Esc” is pressed, followed by the “↓ ” key. The menu choices or settings are:
• Contrast
• Language select

112 Installing Priva Compass - 00.019

 Groscale

The “↑ ” and “ ↓ ” keys are used to toggle between these two settings. By pressing “Enter”, the
setting currently displayed will be activated. The following instructions explain how the display
contrast itself can be adjusted:
• Activate the setting Contrast by pressing “Enter”; on the display, the double brackets 50<<50
will change to 50>>50 .
• Press “ ↑ ” to obtain a stronger contrast or press “ ↓ ” to obtain a lighter contrast. The result
will be visible immediately since the display changes according to the instruction given.
Pressing the key down for a longer period of time will increase the speed at which the value
changes.
• Press “Enter” to record the adjustment to the contrast or press “Esc” if no change is to be
made.

Menu structure

Menu Value or setting Set-up range Default

Measurements Nett weight
# of Load Cells
Tare Weight
Saturated Slab
Max #kg/5V
Display Contrast 0 - 100% 50%
Language select Dutch/English/German/French Dutch
Load Cells Sensitivity 1 1,9000 - 2,1000 2,0000
Zero 1 -0,1000 - 0,1000 0,0000
Sensitivity 2 1,9000 - 2,1000 2,0000
Zero 2 -0,1000 - 0,1000 0,0000
Sensitivity 3 1,9000 - 2,1000 2,0000
Zero 3 -0,1000 - 0,1000 0,0000
Sensitivity 4 1,9000 - 2,1000 2,0000
Zero 4 -0,1000 - 0,1000 0,0000
# of Load Cells 1-4 2
#kg/Load Cell 1 - 500 kg 50 kg
Set tare Weight confirm -
Adj. Adjust Sens. -10.000 - 10.000 ppm 0 ppm
Slab calibration Set tare Weight confirm
Saturated Slab confirm
Adj. Nett Weight Nett weight -20.000 - 20.000 g
Test Outputs Toggle Outputs 0 or 1 (0 = off, 1 = on) 0
Service Tare Weight -5.000 200.000 g
Saturated Slab 0.0 - 200.000 g
Max #kg/5V 5 - 200 kg

The menus coloured grey in the above table can only be accessed after a certain key combination
is pressed. This way, they are protected from their contents being unintentionally changed. Please
find an explanation of the meaning of the menus themselves in the chapter “Explanation menus”.

Explanation menus
In this chapter the structure and meaning of the menus is described. (see also chapter “Operation
and display”)

Installing Priva Compass - 00.019 113

Priva

Measurements

Nett weight

This measurement value shows the actual nett weight which is currently resting on the weighing
unit. This weight is passed to the process computer via the analog outputs. This menu item will
become active automatically after you have started up the indicator or if no operations are performed
for 15 minutes.

# of Load Cells

This shows the number of weighing platforms entered into the weighing indicator. This number
should match the actual number of weighing platforms being used (i.e. 2 or 4).

Tare Weight

This figure indicates the weight in relation to the absolute zero point of the weighing indicator. This
information is gained after performing the Set tare Weight function in Load Cells or Slab calibration.
After finishing with the Slab calibration menu, this figure shows the weight of the unit while only
incorporating a dry slab. This information must be entered on the accompanying form so it can be
entered into any new weighing indicator without first having to calibrate the unit (please also refer
to the menu Service).

Saturated Slab

This figure indicates the weight of saturated substrate slab after using the function Saturated Slab
from the Slab calibration menu. This information must be entered on the accompanying form.

Max #kg/5V

This figure indicates the maximum nett weight in number of kg set by you and which can be passed
to the process computer. It should match an output signal of 5000 mV from the first analog output.
The maximum nett weight to be weighed must never exceed this value.

Display
In this menu, the contrast and choice of language can be set:

Contrast

This allows you to set the contrast between 0 - 100%, which means optimum readability can be
obtained under different light and temperature conditions. This value has a default of 50%.

Language select

This allows you to set the language to Dutch, English, German or French.

114 Installing Priva Compass - 00.019

 Groscale

Load Cells
In this menu, you can enter the load cell data necessary for the weighing indicator to function
properly. The load cell is the sensor inside the weighing platform which measures the weight.
Information such as sensitivity and zero of the separate load cells, the number of load cells and the
weight range of a load cell is involved.

Sensitivity 1 - 4

In this menu item is set the sensitivity for each of the separate load cells. The sensitivity is derived
from the difference voltage given out by the load cell between zero load and maximum load. The
sensitivity of the separate load cells needs to be equal in order to prevent deviations in the weighing
unit.

Zero 1 - 4

In this menu item is entered the voltage given out at zero load by each of the separate load cells.
This is called the zero. The zero load is measured when the weighing platform is empty.

# of Load Cells

In this menu item is entered the number of load cells (weighing platforms) of which the weighing
unit consists. This should be either two (2) or four (4), the default is set at two (2).

#kg/Load Cell

Here, the weight range of each of a separate load cell is entered in kilograms, the default is set to
50 kg. This figure represents the maximum weight which can safely be placed on the platform without
damaging the load cell. The weight range must be the same for all weighing platforms in the unit.

Set tare Weight

This menu item can be used to record the new zero weight. The figure shown on the display is the
actual nett weight. By activating this function, the current weight of the whole weighing unit is set
to 0 kg. This menu item is also part of the menu Slab calibration. After performing the Set tare Weight
function, the new difference in weight between the new zero point and the absolute zero point of
the weighing indicator will be calculated in the item Tare Weight of the Measurements menu.

Adj. Adjust Sens.

This menu item allows you to make corrections in order to rectify small deviations introduced as a
result of installing the weighing unit.

Effect of using the function Ajust Sens.

This can be done by a procentual adjustment of the total sensitivity of the load cells as entered in
the menu items Sensitivity 1 - 4. To do this, check the weighing unit by using large calibration weights
(2x20 kg). Before these are placed on the weighing unit, the unit itself should be tared. Then each
of the calibration weights can be placed at the height of a weighing platform. The actual nett weight
is then adjusted to the absolute calibration weight. It is not necessary to perform this function to
achieve a good performance by the weighing unit.

Installing Priva Compass - 00.019 115

Priva

Slab calibration
In this menu, the data for the weighing unit including the substrate slabs is entered, usually at the
start of a new crop.

Set tare Weight

This function is used to record a new zero weight. Place the dry substrate slab on top of the weighing
unit and perform the Set tare Weight function.

Saturated Slab

This function is used to record the weight of the saturated slab in the weighing indicator, only to
backup your memory. The function Saturated Slab is used only after the function Set tare Weight has
been performed. Place the saturated slab on the weighing unit or drip moisture onto the dry slab
until this is saturated.

Adj. Nett Weight

Effect of using the function Adj. Nett Weight

With this menu the nett weight can be changed by shifting the current zero point. The current nett
weight is shown on the left of the display, while the new nett weight is displayed on the right. This
can be changed by using the arrow keys. This function can be performed after a change in weight
has occurred as a result of crop activity. When this function is to be performed, you should record
the nett weight showing on the display before the crop activity is performed. Also, no water dosage
should take place in the meantime. It is advisable to use this function as little as possible and instead,
change the nett weight by making a change to the hanging plant support system.

Test Outputs
By activating this menu, the process computer cabling can be checked. Both analog outputs will
transmit a reverse phase block-wave with a low relatively high signal of 0 mV and 5000 mV within a
time period of 30 seconds. This way, any short circuiting in the cabling or any loss of voltage in the
cabling can be spotted early.

Service
In this menu, data regarding the weighing unit can be entered directly, which means that the weighing
unit does not have to be calibrated again when the weighing indicator is replaced. The data should
be taken from the accompanying form.

Tare Weight

In this item, you need to enter the weight taken from the accompanying form which represents the
value of the item Tare Weight in the menu Measurements.
Saturated Slab

In this item, you should enter the weight taken from the accompanying form which represents the
value of the item Saturated Slab in the menu Measurements. With this data the Max #kg/5V can be
recorded.

116 Installing Priva Compass - 00.019

 Groscale

Max #kg/5V

In this menu item the number of kilograms that correspond with 5000 mV is recorded. Max #kg/5V
must be derived from the saturated slab weight. The maximum nett weight to be weighed must
never exceed this value. The figure displayed here and under the menu Measurements, item Max
#kg/5V , must be entered on the accompanying form.

Maintenance Groscale
The various parts of the Groscale do not require a great deal of maintenance. In order to guarantee
reliable weighing, the following should be checked on a regular basis. Depending on the crop and
the situation within the company, this check should be performed either weekly or daily.

• Check that nothing has fallen onto the substrate slab (leaves, fruit, flowers).
• Check that no dirt or fruit has dropped underneath the support frame or into the weighing
platforms.
• Check that the plants are still properly supported by the braces.
• Check the reading (in kg) on the display of the weighing indicator.
• Prevent moisture from dripping onto the weighing indicator.

Remove the weighing platforms in the event of a change of crop. Cover the weighing indicator with
a plastic bag to protect it against moisture and cleaning materials, or remove the whole weighing
indicator. Cover the remaining plug with a plastic bag to protect it from moisture and cleaning
materials.

Replacement and repair

Weighing platform
To obtain the desired high level of accuracy a number of sensitivities have been determined for the
weighing platforms. The sensitivity has no bearing on quality, but is determined by the type of output
signal from the weighing platform. The weighing platforms of each weighing indicator should have
the same sensitivity. In case of a breakdown in one of the weighing platforms, it is important that
the repaired or replaced weighing platform has the same sensitivity. This sensitivity is marked on
the label of the load cell cable.

The same applies to the repair or acquisition of a second set of platforms for a weighing indicator.
After repair or after increasing the weighing platforms to four, the correct data should be entered
in the Load Cells menu after the load cell cables have been connected.

Weighing indicator
In the event of a weighing indicator breakdown, the procedure below should be followed:
1. Use the LEDs and the table in the chapter “Fault analysis” to check the voltage on the weighing
indicator and check which of the LEDs are working and which are not.
2. If the supply voltage to the weighing indicator is present but it still does not function, the weighing
indicator should be returned to your supplier. When returning the weighing indicator, please
make sure the following information is available:
• a thorough description of the failure
• remove the form containing the settings for the growing season in question from the weighing
indicator and keep it in a safe place so that the repaired weighing indicator can be set up
for the existing situation.
3. When the weighing indicator is returned, the values of the Tare Weight, Saturated Slab and Max
#kg/5V can be taken from the form you have saved and entered in the menu Service. Here, the
specific figures of the load cells in the Load Cells menu can also be entered, as explained in the
chapter “Commissioning”.

Installing Priva Compass - 00.019 117

Priva

Troubleshooting

Problem Possible cause Solution

The weighing indicator no longer The bolt that determines the Have the position of the adjusting
displays any changes in weight. measurement range has been bolt checked (see picture): in the
rotated. As a result, the full unladen state, there must be a
measurement range is not available. distance of 6 mm between the
underlay and the bolt.
If the distance is too great, the load
cell will be insufficiently protected; if
the distance is too small, the
measurement range will be
incomplete.

The weighing indicator displays Various Perform maintenance checks (see

sudden changes in weight. Maintenance Groscale (page 117)).
Check whether anything has rolled
underneath the weighing platforms.
Place a calibration weight on the
substrate slab and see whether the
weight displayed on the weighing
indicator actually increases by the
value of the calibration weight.
Use a syringe, for instance, to
withdraw 20 ml of liquid from the
slab and see whether the weight
actually decreases by 20 grams.
Check whether the cables are intact
and have been connected correctly.
Use the LEDs in the weighing
indicator to check whether it is
functioning properly.

118 Installing Priva Compass - 00.019

 Groscale

Technical specifications

Groscale
Product Groscale 100 kg
• 1 weighing indicator (part number 3771140)
• 2 weighing platform 50 kg
Groscale 200 kg
• 1 weighing indicator (part number 3771140)
• 2 weighing platform 100 kg
Groscale 400 kg
• 1 weighing indicator (part number 3771140)
• 4 weighing platform 100 kg

Weighing platform
Part number 3771142 (weighing platform for 50 kg)
3771147 (weighing platform for 100 kg)
Accuracy 0.05% Full Scale minimum
Drift at output signal 10 ppm of placed weight /°C
Drift at zero point 23 ppm of weight range /°C
Load cell interface
Number of load cells 1-4
Load cell impedance 415 Ohm ±10%
Agitation voltage 4,4 VAC
Input voltage range -0,1 - 2,4 mV/V
Sensitivity <0.1 μV/div, intern 0.01 V/div
Drift <8 ppm / °C
Analog outputs
Output range 0 - 5300 mV
Work area 0 - 5000 mV
Resolution 1 mV / LSB
Absolute accuracy 0,5% Full Scale
Relative accuracy 0,5 LSB
Output impedance 500 Ohm
Power supply
DC 20 - 38 VDC (power supply galvanically separated)
AC 24VAC ± 10% (power supply galvanically separated)
Power consumption < 4W
Temperature range
Work area 15 - 35°C
Work range 0 - 50°C
Overall system performance
Measuring accuracy 0,1 % Full Scale. minimal
Absolute accuracy data transfer (2 outputs) 4000 parts Full Scale
Relative accuracy data transfer (2 outputs) 50000 parts Full Scale

Installing Priva Compass - 00.019 119

Priva

Other sensor connection examples

These examples illustrate the connection of I/O to the inputs and outputs of Compass.

Connecting I/O to universal input

Connecting isolated sensors with voltage output to

universal input

Connecting non-isolated sensors with voltage output to

universal input

Connecting isolated sensors with current output to

universal input

Connecting non-isolated sensors with current output to

universal input

Connecting current transmitters to universal input

120 Installing Priva Compass - 00.019

 Other sensor connection examples

Connecting resistive sensors to universal input

Connecting two-wire potentiometers universal input

Connecting isolated sensors with open collector output

to universal input

Connecting non-isolated sensors with open collector

output to universal input

Connecting dry contacts to universal input

Connecting powered contacts to universal input

(sourcing)

Installing Priva Compass - 00.019 121

Priva

Connecting powered contacts to universal input (sinking)

Connecting powered solid-state outputs to universal

input (sourcing)

Connecting powered solid-state outputs to universal

input (sinking)

Connecting I/O to digital input

Connecting isolated sensors with open collector output

to digital input

Connecting non-isolated sensors with open collector

output to digital input

122 Installing Priva Compass - 00.019

 Other sensor connection examples

Connecting dry contacts to digital input

Connecting powered contacts to digital input (sourcing)

Connecting powered contacts to digital input (sinking)

Connecting powered solid-state outputs to digital input

(sourcing)

Connecting powered solid-state outputs to digital input

(sinking)

Installing Priva Compass - 00.019 123

Priva

Connecting I/O to analog output

Connecting isolated actuators with voltage input to

analog output

Connecting non-isolated actuators with voltage input to

analog output

Connecting I/O to relay output

Connecting actuators to normally open contact of relay

output

Connecting actuators to normally closed contact of relay

output

124 Installing Priva Compass - 00.019

 Other sensor connection examples

Points to be considered
Non-isolated sensors or actuators with a bridge rectifier also have four connections. These
must be equipped with a "floating" power supply that is not connected to FG.

Connecting non-isolated sensors or actuators with a bridge rectifier to an I/O module

Abbreviations used

Abbreviation or symbol Explanation

AO analogue output
COM common contact
DC direct current
DI digital input
DO digital output
FG field ground
FP ¹ field power
I intensity (of electrical current)
M motor
NC normally closed contact
NO normally open contact
Ref ¹ reference voltage
UI universal input
VAC volts alternating current
VDC volts direct current
¹ Not for Priva Blue ID C-Line.

Installing Priva Compass - 00.019 125

Priva

Disposing of waste products

At the end of its service life the product must be taken to a recognized collection point for waste
electrical equipment.

The product is marked in accordance with European directive 2002/96/EC in relation to

waste electrical and electronic equipment (WEEE):

The mark indicates that the product must not be disposed of together with other household
waste at the end of use. To prevent damage to the environment or to human health resulting
from the uncontrolled disposal of waste, you must keep the product separate from other
types of waste and recycle it (have it recycled) in a responsible manner so that the reuse of
material sources is supported.

126 Installing Priva Compass - 00.019

 General Compass specifications

General Compass specifications

General
Article description Compass 2S Compass 4S
Article number 3772100 3772101
Weight 23 kg 32 kg
Dimensions (W x H x D) 500 x 500 x 210 mm 600 x 600 x 210 mm
Modules • Priva Blue ID C3 C-MX34 • Priva Blue ID C3 C-MX34
Controller (article Controller (article
number 5210001) number 5210001)
• Priva Blue ID C-Line MX34 Mix
input/output module (article
number 5211001)

Optional extension modules • Priva Blue ID C-Line UI8 Universal input module (article number
5213001)
• Priva Blue ID C-Line DOR6 Relay output module (article number
5215001)

Components • single-door cabinet (left-opening door)

• buzzer (article number 3651124)
• Priva Blue ID C-Line IO-bus cable length 72 cm (article number 5219112)
• Priva Gateway (article number 3771810)
• WLAN adapter
• 24 VAC transformer 100/110/120/127/210/220 V - 24V (article number
3653033)
• system power supply and field equipment power supply: Power supply
24 VDC / 75 W (article number 3659054)
• circuit breaker
• earth bar
• fuse
• mounting and connection material

Interfaces • Ethernet (5x)

• USB 2.0
• WLAN

Packaging (dimensions W x H x D) cardboard box (550 x 550 x 230 mm) cardboard box (650 x 650 x 230 mm)

Electrical specifications

Compass 2S Compass 4S
Rated voltage 100-110-120-127-200-220-230 Vac
Mains frequency 50 Hz or 60 Hz
Maximum power consumption 240 VA at 230 Vac
250 VA at 115 Vac
Internal circuit breaker 6 A (Char. C)
Protection class Class I (earth connected chassis)

Installing Priva Compass - 00.019 127

Priva

Other specifications

Compass 2S Compass 4S
Maximum number of 3 6
extension modules 3 on each DIN rail
Cable input bottom: bottom:
• 2x PG21 for Ethernet and fibre optic ¹ • 2x PG21 for Ethernet and fibre optic ¹
• 2x M20 for mains power supply and other • 2x M20 for mains power supply and other
cable cable
• 6x M25 for cabling for field equipment • 10x M25 for cabling for field equipment

Colour RAL7035
Material cabinet sheet steel with polyurethane powder coating
¹ optional

Ethernet
Network standard used IEEE 802.3
100BASE-TX (100 Mbps)
auto negotiation
auto MDIX
Baud rate 10 Mbps and 100 Mbps (auto negotiation)
Power over Ethernet No
Cable type required UTP or STP, minimum category 5
Maximum cable length 100 m (328 ft)
Connector type RJ45, screened

WLAN specifications

Supported specifications IEEE 802.11 b/g/n

Frequency bands 2.4 GHz
5 GHz ETSI
FCC bands
(ETSI/FCC bands to be configured in software)
Protection WEP, WPA, WPA2, TKIP, AES, 802.1x
Interface USB 2.0

128 Installing Priva Compass - 00.019

 General Compass specifications

Preconditions for installation and use

Compass 2S Compass 4S
IP code (NEN-EN-IEC 60529) IP 66
Permitted ambient temperature during 0 … 35 °C
normal operation
Permitted ambient relative humidity 10 … 95 % (non-condensing)
during normal operation
Pollution factor (NEN-EN-IEC 61010-1) 2 (normal, non-conducting pollution)
Permitted temperature for transport -25 … 70 °C
and storage
Permitted ambient relative humidity 0 … 95 % (non-condensing)
for transport and storage
Maximum temperature inside cabinet 50 °C
during normal operation
Maximum heat generated in cabinet 57 W at maximum permitted ambient 75 W at maximum permitted ambient
temperature (active cooling is required temperature (active cooling is required
if more heat is generated) if more heat is generated)
Installation on the wall using four mounting holes
using 4 M8 bolts (minimum length 5 cm) (not included)
Other installation and environmental do not expose to direct sunlight
requirements do not install close to a heat source or outdoors
Maximum installation height 2000 meters above sea level
Installation category II

Installing Priva Compass - 00.019 129

Priva

General specifications of Priva Blue ID C-Line

controllers and modules
System power supply Requirements
The system power supply for the controllers and Mix I/O modules must meet the following requirements.
Output voltage 24 VAC ± 25%; 50/60 Hz ± 5 %
24 VDC ± 10%
Insulation double insulation between input and output
Type of power supply for UL916, CSA C22.2 No. 205: UL listed / CSA certified Class 2 extra
low output voltage power supply

Housing
IP code IP20 (IEC 60529)
Flammability class V-0 (UL 94)
Recycle code 7
Colour housing: white (RAL9001) and blue (NCS S 1560-R90B)
connections and connectors: black (RAL9011)
Type of device open type equipment for:
• indoor use only
• pollution degree 2 environment

Installation and connection

Installation in control panel:
• accessible to authorised personnel only
• can be clicked onto horizontally or vertically positioned DIN
rail. DIN rail installed directly on a mounting plate or floating
with respect to the mounting plate
in DIN 43870 distribution box
Type of DIN rail 35 x 7.5 (1.38 x 0.30 inches) or 35 x 15 mm (1.38 x 0.59 inches)
(height x depth), in accordance with IEC 60715
Connector type for power supply and I/O pluggable terminal block
screw connectors (optional)
Permitted core cross section area solid:: 0.2 … 2.5 mm² (25 … 14 AWG)
flexible with ferrule connector: 0.2 … 2.5 mm² (25 … 14 AWG)
flexible with double ferrule connector: 0.2 … 1.5 mm² (25 … 16
AWG)
Strip length/connector length (terminal block) solid: 10 mm (0.39 inches)
flexible with ferrule connector: 10 mm (0.39 inches)
flexible with double ferrule connector: 12 mm (0.47 inches)
Strip length/connector length (screw connector) 8 mm (0.31 inches)
Identification of connections labelling with an explanatory abbreviation
Maximum length of I/O bus cable between 3 m (9.84 ft)
modules
Maximum length of I/O bus (total, including 20 m (65.62 ft)
modules)

130 Installing Priva Compass - 00.019

 General specifications of Priva Blue ID C-Line controllers and modules

Environment
Permitted temperature inside control panel of a 0 … 50 ºC (32 … 122 °F)
working system (without air flow)
Permitted temperature during transport and -20 … 70 ºC (-4 … 158 °F)
storage
Maximum height 3000 m (9842 ft)
Permitted ambient relative humidity 10%…95% (non-condensing)
Shock resistance EN 60068-2-27 (Ea)
Vibration resistance EN 60068-2-27 (Fc)
Installation category II
Other installation and environmental do not expose to direct sunlight
requirements

Legislation and standards

Canada / USA • UL 916 (energy management equipment)
• UL 61010-1 (measurement and control equipment)
• UL 61010-2-201 (measurement and control equipment)
• CSA C22.2 No 61010-1-12 (measurement and control
equipment)
• CSA C22.2 No 61010-2-201-14 (measurement and control
equipment)
• CSA C22.2 No 61010-1-04 (measurement and control
equipment)
• CSA C22.2 No 205-12 (signal equipment)

EMC • in compliance with 47 CFR Part 15 Subpart B, Class B (FCC

Rules)
Functioning must meet two conditions:
1. The system must not cause harmful interference.
2. The system must acknowledge all interference received,
including interference that may cause unwanted
operations.
• ISM system, in accordance with Canadian standard ICES-001

Europe • Low Voltage Directive 2006/95/EC:

• EN 61010-1 (measurement and control equipment)
• EN 61010-2-201 (measurement and control equipment)
• EMC Directive 2004/108/EC:
• EN 61326-1 (measurement and control equipment)
• EN 61000-6-2 (generic immunity standard)
• EN 61000-6-3 (generic emission standard)
• RoHS directive 2011/65/EU

in compliance with WEEE directive 2012/19/EU

International IEC • IEC 61010-1 (measurement and control equipment)

• IEC 61010-2-201 (measurement and control equipment)

International • The Priva Blue ID C4 C-MX34 Controller and Priva Blue ID C4

C-MX34m Controller with manual override are BTL-registered
with BACnet International.
• The Priva Blue ID C4 C-MX34 Controller and Priva Blue ID C4
C-MX34m Controller with manual override are BACnet-certified
in accordance with ISO 16484-5/6.
• Priva is a member of the BACnet Interest Group Europe.

Installing Priva Compass - 00.019 131

Priva

Specifications of Priva Blue ID C4 C-MX34 Controller

General
Module article description Priva Blue ID C4 C-MX34 Controller
Module article number 5210001
Number of inputs and outputs 0 ... 84 (depending on licence)
Dimensions (XYZ) 140 x 216 x 82 mm (5.5 x 8.5 x 3.2 inches)
Width according to DIN 43880 12 TE (HP) (1 TE = 18 mm (0.71 inches))
Mounting depth for DIN 43870 distribution box ¹ 75 mm (2.95 inches)
Weight 0.6 kg (1.23 lb)
Maximum power consumption (including power 24 VDC: 23.2 W
for USB port, I/O bus and power supply output) 24 VAC: 31.2 VA
Maximum power consumption (excluding power 24 VDC: 8.4 W
for USB port, I/O bus and power supply output) 24 VAC: 12.2 VA
Typical power dissipation ² 6.6 W
MTBF ³ 461,053 hours
Installation clicks onto DIN rail
can be mounted in DIN 43870 distribution box
Housing material mixture of polycarbonate and ABS
Button material TPE (synthetic rubber)
Number of Ethernet ports 4
Number of digital inputs 12, consisting of:
10 x low current pull-up (inputs 1 .. 10)
2 x high current pull-up (inputs 11 and 12)
Number of universal inputs 8
Number of analogue outputs 6
Number of relay outputs 8, consisting of:
5 with normally open contact
3 with changeover contact
Number of RS485 ports 1
Number of alarm outputs 1
Accuracy of internal temperature measurements +/- 2°C (35.6 °F)
¹ measured between the front of the DIN rail and the rear of the cover plate.
² Dissipation under the following conditions:
- I/O load of 50%
- 50% of the LEDs on
³ The MTBF is calculated according to the Telcordia SR-332 standard Issue 3 under the following conditions:
- ambient temperature: 35 … 50°C (95 … 122 °F)
- supply voltage: 24 VDC
- time in operation per day: 24 hours
- reliability level: 60%

132 Installing Priva Compass - 00.019

 General specifications of Priva Blue ID C-Line controllers and modules

Processor
Processor Freescale i.MX6 processor
USB connection file system¹ FAT32
Clock frequency 800 MHz
Working memory 256 MB DDR3 SDRAM
Storage memory 2 GB SLC NAND flash
¹ for future applications

Memory card
Maximum ambient temperature 70°C (158 °F)
Supported SD formats • SDSC: storage capacity up to 2 GB
• SDHC: storage capacity up to 32 GB

File system FAT32

Electrical
System power input 24 VAC ±25%; 50/60 Hz ± 5 %
24 VDC ±10%
System power output (via I/O bus or power supply 24 VDC ±10%
output)
Maximum output power 10 W (combined for I/O bus and power supply output)
Functional isolation of power supply input in 250 V
relation to system neutral
Protection of system power protected against overload and short-circuits by means of a
self-resetting fuse
Accuracy of system power measurement ± 2%
Under-voltage warning level 18.5 … 19.5 VDC
Accuracy of system clock (normal operation) ± 20 ppm 0 ... 50°C (32 …122 °F)
Accuracy of real-time clock (in the event of power ± 20 ppm at 25°C (77 °F)
failure) ± 95 ppm 0 ... 50°C (32 …122 °F)
Type of battery BR2032
Battery service life 5 years
Speed of USB ports¹ 480 Mbps
Maximum output current of USB host connection¹ 500 mA
Indication • blue line-up LED
• green/red LED for status of controller
• green LED for status of I/O

Switching voltage alarm output max. 30 VAC

max. 30 VDC
Switching current alarm output 0.1 mA … 1 A (cosφ = 1)
¹ USB connection for future applications

Installing Priva Compass - 00.019 133

Priva

Ethernet
Network standard used IEEE 802.3
100BASE-TX (100 Mbps)
auto negotiation
auto MDIX
Baud rate 10 Mbps and 100 Mbps (auto negotiation)
Power over Ethernet No
Cable type required UTP or STP, minimum category 5
Maximum cable length 100 m (328 ft)
Connector type RJ45, screened

Specifications of inputs and outputs

For the specifications of the inputs and outputs, see Specifications of inputs and outputs (page 138)

134 Installing Priva Compass - 00.019

 General specifications of Priva Blue ID C-Line controllers and modules

Specifications of Priva Blue ID C-Line MX34 Mix input/output

module

General
Module article description Priva Blue ID C-Line MX34 Mix input/output module
Module article number 5211001
Dimensions (XYZ) 140 x 216 x 62 mm (5.5 x 8.5 x 2.5 inches)
Width according to DIN 43880 12 TE (HP) (1 TE = 18 mm (0.71 inches))
Mounting depth for DIN 43870 distribution box ¹ 53.5 mm (2.11 inches)
Weight 0.5 kg (1.10 lb)
Maximum power consumption (including power 24 VDC: 16.4 W
for I/O bus and power supply output) 24 VAC: 24.3 VA
Maximum power consumption (excluding power 24 VDC: 5.2 W
for I/O bus and power supply output) 24 VAC: 8.8 VA
Typical power dissipation ² 4.1 W
MTBF ³ 796,364 hours
Installation clicks onto DIN rail
can be mounted in DIN 43870 distribution box
Housing material mixture of polycarbonate and ABS
Button material TPE (synthetic rubber)
Number of digital inputs 12, consisting of:
10 x low current pull-up (inputs 1 … 10)
2 x high current pull-up (inputs 11 and 12)
Number of universal inputs 8
Number of analogue outputs 6
Number of relay outputs 8, consisting of:
5 with normally open contact
3 with changeover contact
Accuracy of internal temperature measurements +/- 2 °C (35.6 °F)
¹ measured between the front of the DIN rail and the rear of the cover plate.
² Dissipation under the following conditions:
- I/O load of 50%
- 50% of the LEDs on
³ The MTBF is calculated according to the Telcordia SR-332 standard Issue 3 under the following conditions:
- ambient temperature: 35 … 50°C (95 … 122 °F)
- supply voltage: 24 VDC
- time in operation per day: 24 hours
- reliability level: 60%

Specifications of inputs and outputs

For the specifications of the inputs and outputs, see Specifications of inputs and outputs (page 138)

Installing Priva Compass - 00.019 135

Priva

Specifications of Priva Blue ID C-Line UI8 Universal input module

General
Module article description Priva Blue ID C-Line UI8 Universal input module
Module article number 5213001
Dimensions (XYZ) 140 x 63 x 62 mm (5.6 x 2.5 x 2.5 inches)
Width according to DIN 43880 3.5 TE (HP) (1 TE = 18 mm (0.71 inches))
Mounting depth for DIN 43870 distribution box ¹ 53.5 mm (2.11 inches)
Weight 0.16 kg (0.35 lb)
Maximum power consumption 24 VDC: 1.5 W
Typical power dissipation ² 1.8 W
MTBF ³ 2,190,000 hours
Installation clicks onto DIN rail
can be mounted in DIN 43870 distribution box
Housing material mixture of polycarbonate and ABS
Button material TPE (synthetic rubber)
Number of universal inputs 8
Accuracy of internal temperature measurements +/- 2°C (35.6 °F)
¹ measured between the front of the DIN rail and the rear of the cover plate.
² Dissipation under the following conditions:
- I/O load of 50%
- 50% of the LEDs on
³ The MTBF is calculated according to the Telcordia SR-332 standard Issue 3 under the following conditions:
- ambient temperature: 35 … 50°C (95 … 122 °F)
- supply voltage: 24 VDC
- time in operation per day: 24 hours
- reliability level: 60%

Specifications of inputs
For the specifications of the inputs, see Specifications of inputs and outputs (page 138)

136 Installing Priva Compass - 00.019

 General specifications of Priva Blue ID C-Line controllers and modules

Specifications of Priva Blue ID C-Line DOR6 Relay output module

General
Module article description Priva Blue ID C-Line DOR6 Relay output module
Module article number 5215001
Dimensions (XYZ) 140 x 63 x 62 mm (5.6 x 2.5 x 2.5 inches)
Width according to DIN 43880 3.5 TE (HP) (1 TE = 18 mm (0.71 inches))
Mounting depth for DIN 43870 distribution box ¹ 53.5 mm (2.11 inches)
Weight 0.18 kg (0.40 lb)
Maximum power consumption 24 VDC: 1.2 W
Typical power dissipation ² 1.2 W
MTBF ³ 4,380,000 hours
Installation clicks onto DIN rail
can be mounted in DIN 43870 distribution box
Housing material mixture of polycarbonate and ABS
Button material TPE (synthetic rubber)
Number of relay outputs 6, consisting of
5 with normally open contact
1 with changeover contact
¹ measured between the front of the DIN rail and the rear of the cover plate.
² Dissipation under the following conditions:
- I/O load of 50%
- 50% of the LEDs on
³ The MTBF is calculated according to the Telcordia SR-332 standard Issue 3 under the following conditions:
- ambient temperature: 35 … 50°C (95 … 122 °F)
- supply voltage: 24 VDC
- time in operation per day: 24 hours
- reliability level: 60%

Specifications of outputs
For the specifications of the outputs, see Specifications of inputs and outputs (page 138)

Installing Priva Compass - 00.019 137

Priva

Specifications of inputs and outputs

The various types of inputs and outputs are available on various modules. The module specifications
indicate which inputs and outputs are available on the module in question. The specifications of the
inputs and outputs are described in this chapter.

Digital inputs Alternating current Direct current

Input voltage measurement range 0 … 30 VAC 0 … 30 VDC
Maximum permitted input voltage 0 … 30 VAC -30 … 30 VDC
Type of measurement pulse and status pulse and status
Minimum detectable pulse width 500 ms 10 ms
(Live contact) (Mechanical switch) (Mechanical switch)
500 ms 350 µs
(Electronic switch) (Electronic switch)
Minimum detectable pulse width - 10 ms
(Dry / open collector) (Mechanical switch)
350 µs
(Electronic switch)
Maximum input frequency - 50 Hz
(Live contact, 50% duty cycle) (Mechanical switch)
1,400 Hz
(Electronic switch)
Maximum input frequency - 50 Hz
(Dry / open collector, 50% duty cycle) (Mechanical switch)
1,400 Hz
(Electronic switch)
Maximum input voltage for low 3 VAC 3 VDC
Minimum input voltage for high 12 VAC 12 VDC
Input resistor with pull-up circuit disabled 24 kΩ nominal for positive voltages
19 kΩ nominal for negative voltages
Input resistor with pull-up circuit enabled -1 mA (low current pull-up)
-5 mA (high current pull-up)
Functional isolation of inputs in relation to system 250 V
neutral
Maximum current of FG connections 10 A
Indication (only for modules with manual override) • green/red LEDs for status of inputs (colour is adjustable)

Universal inputs - Analogue use

Type of measurement to be set per input voltage
current
resistance
Mains frequency suppression (NMRR @ 50/60 Hz) -60 dB (applies for a pure sinus)

Universal input - Voltage measurement

Measurement range 0 … 10 V
Maximum permissible input voltage 26.4 VAC
-24 … 30 VDC
Number of measurements per second 50 @ 50 Hz mains frequency
60 @ 60 Hz mains frequency
Resolution 14 bits over 12 V (730 µV)
Accuracy ± (5mV + 0.1% of the measurement)
Input resistance > 1 MΩ
Maximum source resistance 1 kΩ

138 Installing Priva Compass - 00.019

 General specifications of Priva Blue ID C-Line controllers and modules

Universal input - Current measurement

Input current measurement range 0 … 22 mA
Maximum permissible input voltage 26.4 VAC
0 … 30 VDC
Number of measurements per second 50 @ 50 Hz mains frequency
60 @ 60 Hz mains frequency
Resolution 2.3 µA (approximately 13 bits over 20 mA)
Accuracy ± (40 μA + 0.4% of measurement)
Input resistance 250 Ω, nominal
Protection resistor for current measurement is switched off automatically in
the event of overvoltage (self-restoring after 5 minutes)

Universal input - Measurement of resistance

Measuring range (automatic selection) 0 ... 2.5 kΩ 0 ... 10 kΩ 0 ... 40 kΩ 0 - 200 kΩ
Accuracy (nominal, at an ambient temperature of ± (0.8 Ω + 0.22% ± (1.0 Ω + 0.4% ± (2.3 Ω + 0.41% ± (41 Ω + 1.12%
50 ºC (122 ºF)) of the of the of the of the
measurement) measurement) measurement) measurement)
Maximum permissible input voltage 26.4 VAC
-24 … 30 VDC
Number of measurements per second 1 @ 50 Hz mains frequency
1.2 @ 60 Hz mains frequency
Resolution approximately 14 bits
Maximum permitted capacity at input 10 nF

Universal inputs - Digital use Alternating current Direct current

Voltage range 0 … 26.4 VAC 0 … 30 VDC
Maximum permitted input voltage range 0 … 26.4 VAC -24 … 30 VDC
Type of measurements status and pulse status and pulse
Minimum detectable pulse width 500 ms 35 ms
(Live contact) (Mechanical and electronic (Mechanical and electronic
switch) switch)
Minimum detectable pulse width - 1000 ms
(Dry / open collector) (Mechanical and electronic
switch)
Maximum input frequency - 14 Hz
(Live contact, 50% duty cycle) (Mechanical and electronic
switch)
Maximum input voltage "0" 3 VAC 3 VDC
Minimum input voltage "1" 12 VAC 12 VDC
Current from input with pull-up circuit enabled - -4 mA nominal

Installing Priva Compass - 00.019 139

Priva

Universal input - Other

Functional isolation of inputs in relation to system 250 V
neutral
Maximum current of FG connections 10 A
Indication (for modules with manual override or • green/red LEDs for status of inputs for digital use (colour is
indication only) adjustable)

Analogue outputs
Output voltage control range 0 … 10 V
Maximum load current supplied per output 5 mA
(source)
Maximum current load drawn per output (sink)
Load resistance > 2 kΩ
Resolution 600 µV (> 13 bits over 10 V)
Accuracy ± (10 mV + 0.5% of the control signal)
Accuracy of feedback ± 150 mV
Adjustment time 200 ms (to 70% of the set value)
Input leakage current with high impedance maximum 5 µA
output¹
Protection output is short-circuit proof (self-restoring after a brief short
circuit/overload)
output is protected against ± 30 VDC and 30 VAC
Number of switch-on attempts in the event of 5
short circuit or overload²
Functional isolation of outputs in relation to 250 V
system neutral
Maximum current of FG connections 10 A
Indication (for modules with manual override only) • orange LEDs for indication of output voltage
• orange LED for status of control (automatic or manual)

Controls (for modules with manual override only) buttons to set the voltage level of the output manually:
• +: manually increase output voltage
• A: automatic control of output voltage
• -: manually decrease output voltage

¹ The output is high impedance ex-factory; the module has not yet been configured then. In addition, unused
outputs and the outputs where the overload protection has been activated are high impedance.
² After a short-circuit or overload the output is switched back on after 0.5 s. The output switches back off
immediately if the overload is still present. The output performs a maximum of 5 switch-on attempts with a time
interval of 0.5 seconds. After 5 attempts, the output is switched off and manual intervention is required.

140 Installing Priva Compass - 00.019

 General specifications of Priva Blue ID C-Line controllers and modules

Digital relay outputs

Output configuration normally open contact or changeover contact (depending on
output)
Maximum switching voltage 250 VAC (30 VAC when used in Compass)
30 VDC
Maximum switching current 3 A (cosφ = 1)
Maximum switching voltage in USA/Canada when 125 VAC
switching different mains voltage phases on the
same module
External fuse 8 A maximum
Expected service life of relay contacts with cosφ up to 250 VAC and 3 A: 300,000 switches
= 1 and maximum of 6 switches per minute 24 VDC and 3 A: 300,000 switches
Expected service life of relay contacts with cosφ 250 VAC and 2 A AC15: 200,000 switches
≠ 1 and maximum of 6 switches per minute 250 VAC motor 370 W AC3: 300,000 switches
24 VDC and 3 A L/R 7 ms: 100,000 switches
24 VDC and 1 A DC13: 200,000 switches
UL certified service life of relay contacts with cosφ up to 250 VAC and 3 A: 30,000 switches
= 1 and maximum of 6 switches per minute 24 VDC and 3 A: 30,000 switches
UL certified service life of relay contacts with cosφ 240 VAC and 0.5 hp motor: 1,000 switches
≠ 1 and maximum of 6 switches per minute 120 VAC and 0.25 hp motor: 1,000 switches
B300 pilot duty rating: 6,000 switches
Maximum switching frequency 6 times per min.
Fail-safe if communication with the controller fails, the outputs are set to
a user-configured state
Indication (for modules with manual override only) • green/red LEDs for status of outputs (colour is adjustable)
• orange LED for status of control (automatic or manual)
• red alarm LED

Controls (for modules with manual override only) buttons for manual operation to control connected equipment:
• 0: relay off
• A: automatic or manual control
• 1: relay on

Installing Priva Compass - 00.019 141

Priva

LEDs and line-up LED

During the various phases of commissioning and operation, the LEDs on the modules and the line-up
LED should be predictably on or off, or flashing. The figure and table below show the possible flashing
patterns. After that, there follows an explanation of the meaning of the flashing patterns on the
controller and all modules.

Flashing patterns
Behaviour Line-up LED LEDs

A LED is continuously on - x x
B LED is continuously off - x x
C LED flashing slowly 0.5 sec. on / 0.5 sec. off x
D LED flashing irregularly 0.2 sec. on / 0.5 sec. off x
E LED flashing quickly 0.2 sec. on / 0.2 sec. off x x

142 Installing Priva Compass - 00.019

 General specifications of Priva Blue ID C-Line controllers and modules

General

LED When Colour Pattern (sec.)

A. Line-up module in expected blue on
position
module not in expected blue 0.2 on / 0.2 off
position
module not operational
module is updating or
resetting
fatal error
energy-saving - off
mode
B. CPU status ¹ operational green on
system power present green on
platform update green 0.5 on / 0.5 off
software download green 0.5 on / 0.5 off
wiping memory orange 0.5 on / 0.5 off
non-fatal error green 0.2 on / 0.5 off
module startup error red 0.5 on / 0.5 off
fatal error red 0.2 on / 0.2 off
energy-saving green on
mode
C. I/O status operational green on
non-fatal error green 0.5 on / 0.5 off
software download green 0.2 on / 0.5 off
fatal error green 0.2 on / 0.2 off
¹ For controllers only.

Installing Priva Compass - 00.019 143

Priva

RS485

LED When Colour Pattern (sec.)

A. RX (receive) there is communication orange 0.1 s on / 0.1 s off
there is no - off
communication
B. TX (transmit) there is communication orange 0.1 s on / 0.1 s off
there is no - off
communication
C. status of port operational green on
communication error red on
software download green 0.5 s on / 0.5 s off
non-fatal error green 0.2 s on / 0.5 s off
fatal error green 0.2 s on / 0.2 s off
not operational - off
energy-saving - off
mode

144 Installing Priva Compass - 00.019

 General specifications of Priva Blue ID C-Line controllers and modules

Ethernet

LED When Colour Pattern (sec.)

A. status of Ethernet connection present green on
connection absent - off
B. data communication there is communication yellow flashing randomly
there is no - off
communication

Installing Priva Compass - 00.019 145

Priva

EC Declaration of Conformity
The manufacturer:

Manufacturer’s name Priva B.V.

Manufacturer’s address Zijlweg 3

2678 LC De Lier
P.O. Box 18 De Lier
2678 ZG De Lier
The Netherlands

declares that the products: Priva Compass 4s

Priva Compass 2s

are in accordance with the following European directives:

Number Subject
2014/35/EU Low Voltage
2014/30/EU EMC
2014/53/EU Waste of electrical and electronic equipment
2011/65/EU Hazardous substances in electrical and electronic equipment

and conform to the following standards:

Number Subject
EN 61010-1: 2010 Safety requirements for electrical equipment for measurement,
control, and laboratory use - Part 1: General requirements
EN 60950-1: 2006 Information technology equipment - Safety - Part 1: General
A11:2009 requirements
A1: 2010
A12: 2011
AC: 2011
A2: 2013
EN 61326-1: 2013 Electrical equipment for measurement, control and laboratory
use - EMC requirements - Part 1: General requirements
EN 61000-3-2: 2014 Electromagnetic compatibility (EMC) - Part 3-2: Limits - limits for
harmonic current emissions (equipment input current 16 A per
phase

The technical file is composed by the R&D department of Priva B.V.

The Netherlands, De Lier, April 2017

M. Prins
Chief Executing Officer

146 Installing Priva Compass - 00.019

 Declaration of Conformity for environmental conditions

Declaration of Conformity for environmental

conditions

concerning Halogens/Chlorine Fluorine Hydrocarbons

The manufacturer:

Manufacturer’s name Priva B.V.

Manufacturer’s address Zijlweg 3

2678 LC De Lier
P.O. Box 18 De Lier
2678 ZG De Lier
The Netherlands

declares that the products Priva Compass 4s

Priva Compass 2s

with the aspect to used materials as well as the manufacturing processes, do not contain halogens or derived
substances known as chlorine fluorine hydrocarbons.

The Netherlands, De Lier, January 2016

M. Prins
Chief Executing Officer

Installing Priva Compass - 00.019 147

Priva (head office)
Zijlweg 3
2678 LC De Lier
The Netherlands

See www.priva.com for contact information of a Priva office or partner for your region.

5001018