1 2 3 4

BT401 -- DAC Output

Notes:
Audio Circuit
1. Unused pins should be left floating; do not connect them to ground with a resistor or Headphone Output
pull them up to the power supply. DACL R2 22R 3
2. The module's power supply should preferably be isolated from other parts, with the 2
UART is here
C1 106 4
main power supply being +5.0V [PIN--13]. DACR R4 22R 1
3. The module has an internal 3.3V reference LDO, so there is no need to supply 3.3V C2 106
A [PIN--6]. A
4. The module's optimal operating voltage is 4.2V; you can directly connect 5V through Pin 26: Connect to the MCU's RX pin, operates at 3.3V logic level, compatible with 5V.
Pin 25: Connect to a 5V logic level through a 1KΩ resistor in series. Note: This is analog ground
a diode.
5. The USB drive's power supply is the same as the main chip's, which is +5.0V. UART---115200bps default AUX Input
BT401 28 Bluetooth Antenna AUX1R R5 22R C3 105 1
4 The MUTE pin enables an automatic detection function 4
TX When pulled up, high - MUTE, low - operation 2
3
27 Antenna Ground RX When pulled down, low - MUTE, high - operation AUX1L R6 22R C4 105 3
2
AUX1L PA3 1 26 PB0 TX 5.0V
PA3 PB0 1
AUX1R PA4 2 25 PB1 RX
PA4 PB1 Schematic reserves AUX input circuit.
ADKEY PA5 3 24 PB2 IO4
PA5 PB2
DM FCC-TX 4 23 PB3 MUTE Connect to the enable pin of a power amplifier. Component placements also reserved on the carrier board.
USBDM PB3
Ensure that test points for the USB are brought out. DP FCC-RX 5 22 PB4 IO1 NC If not used, the pin can be left floating.
USBDP PB4 Solder components when needed for use.
Note that the 3.3V output is internal to the module. VCC33 3V3 6 21 PB5 NC
3V3 PB5
MIC_VDD DACVDD7 20 PB6 IO3 NC
DACVDD PB6 BLEU
MIC PA0 8 19 PR1 LED R9 1K Overall Status Indicator LED
PA0 PR1
DACRout R3 1K C2 105 DACR DACR 9 18 PR2 ENABLE R32 1K LED UART Receive Indicator LED
DACR PR2
DACLout R4 1K C3 105 DACL DACL 10 17 PC5 SDCLK SPIDO
DACL PC5
SGND SGND 11 16 PC4 SDCMD SPICLK
SGND PC4 MIC1
Headphone Connection GND GND 12 15 PC3 SDDAT SPICS
GND PC3 MIC C4 105
5.0V 5V0V 13 14 PC1 IO R31 1K LED BLE Connection Indicator LED
2
B Analog Ground is Audio Ground +5.0V PC1 B
1
Pay attention to separate ground handling

DACVDD
Left Side is Analog Ground, Right Side is Digital Ground
They converge at the power supply input. R10 6K2

Call Circuit can also be used for recording function.

Analog Ground and Digital Ground Must Be Shorted at the Power Input: This is very important!!!
Software modification enables this; hardware circuit is universal.

TF Card Supports only FAT or FAT32 file systems.Max capacity: 32GB. SPIFLASH Circuit-Unused pins can be left floating Button Circuit-Unused pins can be left floating HX8358: MUTE Description: OFF
5V power supply, 4Ω 3W. Low level: Enables power amplifier
TF Pin 3 low: Class D mode. ON
9 R3 3K SDCLK High level: Disables power amplifier
1. The SPI Flash chip uses a wide-body SOP8 package. Refer to the Recommended: Pull Pin 3 high for Class AB mode.
8
7 provided PCB files for details. Pin 3 floating: Class D mode.
SDDAT
6 2. The choice of SPI Flash is not manufacturer-specific and supports up HK9108:
C C10 5V power supply, 4Ω 3W. C
5 SDCLK to 16MB (megabytes) in size.The current firmware supports a maximum PA5 AD_KEY
4 VCC33 Pin 3 low: Class AB mode.
of 16MB. For larger sizes, contact the supplier to modify the firmware. C-102P Recommended: Pull Pin 3 high for Class D mode.
3 SDCMD
3. For Flash chips exceeding 16MB, the package may change. Check the Pin 3 floating: Class AB mode. C11
2 R10 0R K1 Play/Pause
1 datasheet for details. As Flash chips come in both wide-body and narrow- R4 10K
body packages, It's recommended that users design the PCB to be Previous Track/Volume - 226
R11 3K K2
TF-9P U1
compatible with both wide-body and narrow-body packages.
MUTE 1 8
R12 6.2K K3 Next Track/Volume + SD VOP SPK
4. Supports direct USB copying to SPI Flash.
C5 105 2 7 1
U-Disk and TF Card: Same principle for both. BYP GND +
W25Q80/25Q16/25Q32/25Q64 R13 9.1K K4 Switch Mode
VMCU R3 NC 3 6 VMCU 2
SPICS 1 8 VCC33 MODE VDD -
5

USB1 CS/ VCC

SPIDO 2 7 R14 15K K5 Volume Up(+) C3 104 4 5
VCC5.0V SO HOLD/ IN VON
VCC33 3 6 SPICLK
WP/ SCK
DM DM 4 5 R15 24K K6 Volume Down(-) HX8358/HK9108
GND SI
DP DP U2 R1 33K DACL
R5 0R R16 33K K7 Previous Track/Fast Rewind
GND
Next Track/Fast Forward R2 33K DACR
R17 51K K8
6

D D
R18 100K K9 Switch Playback Mode Title： BT401 Bluetooth Module -DAC Output Standard Version

R19 220K K10 Power On/Off

Size： A4 Date： November 24,2019 Version：
V7
Analog and Digital Ground: Short together at power input. Unused Components: All can be left floating.
Author： Remarak： Qingyue Electronics
1 2 3 4