Physics 101

Lecture 12
Static Equilibrium
Assoc. Prof. Dr. Ali ÖVGÜN
EMU Physics Department
 Static Equilibrium
❑ Equilibrium and static
equilibrium
❑ Static equilibrium
conditions
◼ Net external force must
equal zero
◼ Net external torque must
equal zero
❑ Center of gravity
❑ Solving static equilibrium
problems
12/20/2024
 Static and Dynamic
Equilibrium
❑ Equilibrium implies the object is at rest (static)
or its center of mass moves with a constant
velocity (dynamic)
❑ We will consider only with the case in which
linear and angular velocities are equal to zero,
called “static equilibrium” : vCM = 0 and  = 0
❑ Examples
◼ Book on table
◼ Hanging sign
◼ Ceiling fan – off
◼ Ceiling fan – on
◼ Ladder leaning against wall 12/20/2024
 Conditions for Equilibrium
❑ The first condition of
equilibrium is a statement of
translational equilibrium
❑ The net external force on the
object must equal zero
  
Fnet =  Fext = ma = 0

❑ It states that the translational

acceleration of the object’s
center of mass must be zero

12/20/2024
 Conditions for Equilibrium
❑ If the object is modeled as a
particle, then this is the only
condition that must be
satisfied  
Fnet =  Fext = 0
❑ For an extended object to be
in equilibrium, a second
condition must be satisfied
❑ This second condition
involves the rotational motion
of the extended object

12/20/2024
 Conditions for Equilibrium
❑ The second condition of
equilibrium is a statement of
rotational equilibrium
❑ The net external torque on
the object must equal zero
  
 net =  ext = I = 0
❑ It states the angular
acceleration of the object to
be zero
❑ This must be true for any axis
of rotation
12/20/2024
 Conditions for Equilibrium
❑ The net force equals zero F = 0
◼ If the object is modeled as a particle, then
this is the only condition that must be
satisfied
❑ The net torque equals zero   = 0
◼ This is needed if the object cannot be
modeled as a particle
❑ These conditions describe the rigid objects
in the equilibrium analysis model

12/20/2024
 Static Equilibrium
❑ Consider a light rod subject to the two
forces of equal magnitude as shown in
figure. Choose the correct statement
with regard to this situation:
(A) The object is in force equilibrium but
not torque equilibrium.
(B) The object is in torque equilibrium but
not force equilibrium
(C) The object is in both force equilibrium
and torque equilibrium
(D) The object is in neither force
equilibrium nor torque equilibrium
12/20/2024
 Equilibrium Equations
❑ For simplicity, We will restrict the applications
to situations in which all the forces lie in the
xy plane.
 
❑ Equation 1: Fnet =  Fext = 0 : Fnet , x = 0 Fnet , y = 0 Fnet , z = 0
 
❑ Equation 2: net  =   ext = 0 :  net , x = 0  net , y = 0  net , z = 0

❑ There are three resulting equations

Fnet , x =  Fext , x = 0
Fnet , y =  Fext , y = 0
 net , z =   ext , z = 0
12/20/2024
12/20/2024
12/20/2024
❑ EX: A seesaw consisting of a uniform board of mass mpl
and length L supports at rest a father and daughter with
masses M and m, respectively. The support is under the
center of gravity of the board, the father is a distance d
from the center, and the daughter is a distance 2.00 m
from the center.
❑ A) Find the magnitude of the upward force n exerted by
the support on the board.
❑ B) Find where the father should sit to balance the system
at rest.

12/20/2024
A) Find the magnitude of Fnet , y = n − mg − Mg − m pl g = 0
the upward force n exerted n = mg + Mg + m pl g
by the support on the
board.  net , z =  d +  f +  pl +  n
B) Find where the father
= mgd − Mgx + 0 + 0 = 0
should sit to balance the
system at rest. mgd = Mgx
m 2m
x =  d =  2.00 m
M  M

Fnet , x =  Fext , x = 0
Fnet , y =  Fext , y = 0
 net , z =   ext , z = 0
12/20/2024
 Axis of Rotation
❑ The net torque is about an axis through any
point in the xy plane
❑ Does it matter which axis you choose for
calculating torques?
❑ NO. The choice of an axis is arbitrary
❑ If an object is in translational equilibrium and
the net torque is zero about one axis, then the
net torque must be zero about any other axis
❑ We should be smart to choose a rotation axis to
simplify problems

12/20/2024
 B) Find where the father should sit to balance the system at rest.
Rotation axis O Rotation axis P
 net , z =  d +  f +  pl +  n  net , z =  d +  f +  pl +  n
= mgd − Mgx + 0 + 0 = 0 = 0 − Mg (d + x) − m pl gd + nd = 0
mgd = Mgx − Mgd − Mgx − m pl gd + ( Mg + mg + m pl g )d = 0
m 2m mgd = Mgx
x =  d =
M  M m  2m
x=  d =
M  M

P O
Fnet , x =  Fext , x = 0
Fnet , y =  Fext , y = 0
 net , z =   ext , z = 0
12/20/2024
 Center of Gravity
❑ The torque due to the gravitational force on an
object of mass M is the force Mg acting at the
center of gravity of the object
❑ If g is uniform over the object, then the center
of gravity of the object coincides with its center
of mass
❑ If the object is homogeneous and symmetrical,
the center of gravity coincides with its geometric
center

12/20/2024
Where is the Center of Mass
?
❑ Assume m1 = 1 kg, m2 = 3 kg, and x1 =
1 m, x2 = 5 m, where is the center of
mass of these two objects? x = m1 x1 + m2 x2
m1 + m2
CM
A) xCM = 1 m
B) xCM = 2 m
C) xCM = 3 m
D) xCM = 4 m
E) xCM = 5 m
12/20/2024
 Center of Mass (CM)
❑ An object can be divided into
many small particles
◼ Each particle will have a
specific mass and specific
coordinates
❑ The x coordinate of the
center of mass will be
m x i i
xCM = i

m i
i

❑ Similar expressions can be

found for the y coordinates

12/20/2024
 Center of Gravity (CG)
❑ All the various gravitational forces acting on all the
various mass elements are equivalent to a single
gravitational force acting through a single point called
the center of gravity (CG)
Mg CG xCG = (m1 + m2 + m3 + ) g CG xCG
=m1 g1 x1 + m 2 g 2 x2 + m3 g 3 x3 + 

❑ If g1 = g 2 = g 3 = 

❑ then
m1 x1 + m 2 x2 + m 3 x3 +   mi xi
xCG = =
m1 + m2 + m3 +   mi
12/20/2024
 CG of a Ladder
❑ A uniform ladder of E
length l rests against a
smooth, vertical wall.
When you calculate the D
torque due to the
gravitational force, you
have to find center of C
gravity of the ladder.
The center of gravity B
should be located at
A
12/20/2024
 Ladder Example
❑ A uniform ladder of length
l rests against a smooth,
vertical wall. The mass of
the ladder is m, and the
coefficient of static friction
between the ladder and
the ground is s = 0.40.
Find the minimum angle 
at which the ladder does
not slip.

12/20/2024
Problem-Solving Strategy 1
❑ Draw sketch, decide what is in or out the system
❑ Draw a free body diagram (FBD)
❑ Show and label all external forces acting on the object
❑ Indicate the locations of all the forces
❑ Establish a convenient coordinate system
❑ Find the components of the forces along the two axes
❑ Apply the first condition for equilibrium
❑ Be careful of signs F = F =0
net , x ext , x

Fnet , y =  Fext , y = 0

12/20/2024
 Which free-body diagram is
correct?
❑ A uniform ladder of length l rests against a smooth,
vertical wall. The mass of the ladder is m, and the
coefficient of static friction between the ladder and
the ground is s = 0.40. gravity: blue, friction:
orange, normal: green

A B C D
12/20/2024
❑ A uniform ladder of length l rests against a smooth,
vertical wall. The mass of the ladder is m, and the
coefficient of static friction between the ladder and the
ground is s = 0.40. Find the minimum angle  at which
the ladder does not slip.

 Fx = f x − P = 0
 Fy = n − mg = 0
P = fx
n = mg
P = f x ,max =  s n =  s mg
mg

12/20/2024
Problem-Solving Strategy 2
❑ Choose a convenient axis for calculating the net torque
on the object
◼ Remember the choice of the axis is arbitrary
❑ Choose an origin that simplifies the calculations as
much as possible
◼ A force that acts along a line passing through the origin
produces a zero torque
❑ Be careful of sign with respect to rotational axis
◼ positive if force tends to rotate object in CCW
◼ negative if force tends to rotate object in CW
◼ zero if force is on the rotational axis
❑ Apply the second condition for equilibrium  net , z =   ext , z = 0
12/20/2024
 Choose an origin O that simplifies the
calculations as much as possible ?
❑ A uniform ladder of length l rests against a smooth, vertical
wall. The mass of the ladder is m, and the coefficient of
static friction between the ladder and the ground is s =
0.40. Find the minimum angle.
A) B) C) O D)

O
O

mg mg mg mg

12/20/2024
❑ A uniform ladder of length l rests against a smooth,
vertical wall. The mass of the ladder is m, and the
coefficient of static friction between the ladder and the
ground is s = 0.40. Find the minimum angle  at which
the ladder does not slip.

 O =  n + f + g + P
l
= 0 + 0 + Pl sin  min − mg cos  min = 0
2
sin  min mg mg 1
= tan  min = = =
cos  min 2 P 2  s mg 2  s
1 1
 min = tan −1 ( ) = tan −1[ ] = 51 mg
2 s 2 ( 0 .4 )

12/20/2024
Problem-Solving Strategy 3
❑ The two conditions of equilibrium will give a system of
equations
❑ Solve the equations simultaneously
❑ Make sure your results are consistent with your free
body diagram
❑ If the solution gives a negative for a force, it is in the
opposite direction to what you drew in the free body
diagram
Fnet , x =  Fext , x = 0
❑ Check your results to confirm
Fnet , y =  Fext , y = 0
 net , z =   ext , z = 0
12/20/2024
 Horizontal Beam Example
❑ A uniform horizontal beam with a
length of l = 8.00 m and a weight
of Wb = 200 N is attached to a wall
by a pin connection. Its far end is
supported by a cable that makes
an angle of  = 53 with the beam.
A person of weight Wp = 600 N
stands a distance d = 2.00 m from
the wall. Find the tension in the
cable as well as the magnitude and
direction of the force exerted by
the wall on the beam.

12/20/2024
 Horizontal Beam Example
❑ The beam is uniform
◼ So the center of gravity
is at the geometric
center of the beam
❑ The person is standing on
the beam
❑ What are the tension in
the cable and the force
exerted by the wall on
the beam?

12/20/2024
 Horizontal Beam Example, 2
❑ Analyze
◼ Draw a free body
diagram
◼ Use the pivot in the
problem (at the wall)
as the pivot
◼ This will generally be
easiest
◼ Note there are three
unknowns (T, R, )

12/20/2024
 Horizontal Beam Example, 3
❑ The forces can be
resolved into
components in the
free body diagram
❑ Apply the two
conditions of
equilibrium to obtain
three equations
❑ Solve for the
unknowns

12/20/2024
 Horizontal Beam Example, 3
l
  z = (T sin  )(l ) − W p d − Wb ( ) = 0
2
l
W p d + Wb ( )
T= 2 = (600 N )( 2m) + (200 N )( 4m) = 313N
l sin  (8m) sin 53

 Fx = R cos  − T cos  = 0
 Fy = R sin  + T sin  − W p − Wb = 0

R sin  W p + Wb − T sin 
= tan  =
R cos  T sin 
 W p + Wb − T sin  
 = tan −1   = 71.7 
 T sin  
T cos  (313N ) cos 53
R= = = 581N
cos  cos 71.7 
12/20/2024
12/20/2024
12/20/2024
12/20/2024
12/20/2024
12/20/2024
12/20/2024
12/20/2024
12/20/2024
12/20/2024
12/20/2024
12/20/2024
12/20/2024
12/20/2024
12/20/2024
12/20/2024
12/20/2024
P1:

12/20/2024
P2:

P3:

12/20/2024
P4:

12/20/2024
P5:

12/20/2024
12/20/2024
P7:

12/20/2024