0% found this document useful (0 votes)
46 views3 pages

Ect202 Analog Circuits, December 2024

The document is an examination paper for the B.Tech Degree in Analog Circuits at APJ Abdul Kalam Technological University, scheduled for December 2024. It consists of two parts: Part A with short answer questions and Part B with detailed questions from various modules. Topics covered include circuit design, amplifier characteristics, feedback effects, and oscillator design.

Uploaded by

Uthara D
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
46 views3 pages

Ect202 Analog Circuits, December 2024

The document is an examination paper for the B.Tech Degree in Analog Circuits at APJ Abdul Kalam Technological University, scheduled for December 2024. It consists of two parts: Part A with short answer questions and Part B with detailed questions from various modules. Topics covered include circuit design, amplifier characteristics, feedback effects, and oscillator design.

Uploaded by

Uthara D
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

-l

B 02008cT202052402

RegNo.: Name:

APJ ABDUL KALAM TECHNOLOGICAL UMYERSITY


B.Tech Degree S4 (S, FE) / 52 (PT) (S, FE) / 54 (WP) (S) Examination Decembet2024

Course Code ECi|fIV2


Course Name: ANALOG CIRCUITS
Max. Marks: 100 Duration:3 Hours

PART A
Mrrkr

I Design a oircuit to obtain square wave output from triangular wave input with 3

5kHz frequency.
2 In a fixed bias circuit Rg=560KC1, Rc:3kfl. Let Vcc:I2V, pdc=100. Determine 3

the value of operating point. Choose Si Transistor.

3 Define the small signal parameterS gm, re and r' for a BJT amplifier. 3

4 Draw the dc and ac load line of RC coupled amplifier with bypass capacitor. 3

5 Compane BJT and MOSFET. 3

6 Discuss the common source MOSFET stage with diode-connected load. 3

7 Emitter follower is a Voltage series feedback amplifier. Justiff the statement. 3

8 State and explain Barkhausen criteria for sustained oscillations 3

9 Compare various classes of Power amplifiers. 3

l0 Discuss the principle of output current boosting in voltage regulator 3

PART B
(Answer onefull questionfrom each module, each question carries 14 marhs)

Module -l
I I a) Design a clamper circuit to get Vo:l0Sin(100g) -10V. Draw its i/p and o/p wave 7

b) What do you mean by thermal run away? How thermal stabilization is achieved in 7

an RC coupled amplifier? Explain with neat sketches and equations.

12 a) Design a filter such that lower cutoff fiequency equal to zero and upper cutoff
frequency equal to 5kHz.
q) Derive design equation of RC Differentiator. Show that output voltage is directly
proportional to the derivative of input voltage.

Page 1 of 3
v

0200EcTz020s2402

Module -2
l3 a) Draw the high frequency hybrid - r equivalent circuit of a CE Amplifier and derive 9
the expression for mid band gain and upper cut off frequency
b) For an RC coupled amplifier with bypass capacitor, Rr: I 00 KO, Rz=20 Kf,), Rc:3 5

Kf,), Re=l Kfl and Vcc=I2 V. The p of the transistor is very high. Calculate the
mid band gain of the amplifier.
14 a) For a CE amplifier with potential divfder bias, Rr=56 KO, Rz: 12.2 K{1, Rc=2 l0
KC), Re:0.4 KO and supply voltage Vcc=10 V. The signal source has a source
resistance.Of 0.5 KO and p of the transistor is given as 100. Calculate the small
signal model parameters gm, rr and rcand obtain the voltage gain, input impedance
and output impedance of the amplifier. [A bypass capacitor is connected across the

emitter resistor]

b) State and explain Miller's Theorem. 4


Module -3
15 a) Calculate the drain current and drain-to-source voltage of a common source circuit 8
' with an n-channel enhancement mode MOSFET. Given: Rr=22 KO, Rz= l0 KO,
Ro=6.8 K(1, Voo= 8V, Vrl V, Kn= 0.1 mA/V2. Also, calculate small signal
voltage gain, input and output impedance.
b) Why is the bandwidth of a cascode amplifier large when compared to Common 6

source amplifier?

16 a) Derive small signal voltage gain, input and output resistance of Common source 9

amplifier with constant current source.


b) In an Enhancement MOSFET Voltage divider bias circuit threshold voltage 5

(VIF2V and the drain current of 8meat a gate source voltage of 6 V. Calculate the

- drain current for a Q- point defined by Vcs:4 V and Vos:10 V.


M6iule 4
17 a) Explain the working of Wien bridge oscillator and derive feedback factor and 9

frequency of oscillation.
b) Design a Hartley oscillator to generate lMHz sine wave. 5

l8 a) Explain any two effects of negative feedback on amplifier performance. 7


b) Determine the voltage gain, input and output resistance with feedback for voltage 7

series feedback having 4'=-100, Ri:lOKO and R":20KO for p:-0.10

Page 2 of 3
UffifiIG'iNgE,
ModJt-5
19 a) Exphii ISG tsorkhg of3rris rt&s,fiUd$or. Drfur drc crpmgfon erry
voltaga
mrrt rhS6x, d[s$s fte pt*cfi$r in scrhr rfto

ofrTrmfrrrcr porrcr aiqdificrd'*rirc


cfticnsy.
ofCom@ffiy ptrh pdl powrqlifu
-12V. If RL{ n, lnprt poum, lshll
d&&wy.
{x

' ' :'-'


"'1:..,1:1i:..
;.;;:'
'Sli;''i
,sti
:;j2' ;{'
' fli!,
'iiWliir,
iil:;

.r;1,. .
Ci;)i:j'
f-a
ttri
.*:
*
!*
1:'.
iti::
J
' ,-,]l

- "dll:i
#iir
. ir*
.W
iri
;'..
?" .,,i1

;,'i*;i::
r,':.
.ilt-
i$li',

iiir;:!ji::
:rifi'::.1:
j?; )

' *ix

'' :
'':irl!i^::

P*tl*f3
7
,

You might also like