AP Series Indoor Wireless LAN Access Points

Quick Start Guide

Copyright © Huawei Technologies Co., Ltd. 2012. All rights reserved.
No part of this document may be reproduced or transmitted in any form or by any means without prior written
consent of Huawei Technologies Co., Ltd.
Trademarks and Permissions

and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.

All other trademarks and trade names mentioned in this document are the property of their respective holders.

Notice
The purchased products, services and features are stipulated by the contract made between Huawei and the
customer. All or part of the products, services and features described in this document may not be within the
purchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information,
and recommendations in this document are provided "AS IS" without warranties, guarantees or
representations of any kind, either express or implied.

The information in this document is subject to change without notice. Every effort has been made in the
preparation of this document to ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute the warranty of any kind, express or implied.

Huawei Technologies Co., Ltd.

Address: Huawei Industrial Base
Bantian, Longgang
Shenzhen 518129
People’s Republic of China
Website: http://enterprise.huawei.com

1
 Preface
This document describes the hardware configuration, installation preparation, installation method, installation
procedure, cable connection, and procedure for logging in to the indoor APs.
The preface is organized as follows:
• Intended Audience
• Symbol Conventions
• Documentation Obtaining
• Technical Support

Intended Audience
This document is intended for:
• Hardware installation engineers
• Onsite maintenance engineers
• Network administrators configuring and maintaining the network

Symbol Conventions
The symbols that may be found in this document are defined as follows:

Symbol Description

CAUTION indicates a potentially hazardous situation that, if not avoided,

could result in equipment damage, data loss, performance deterioration, or
unanticipated results.
Provides additional information to emphasize or supplement important points
NOTE of the main text.
WARNING indicates a hazard with a low level of risk which, if not avoided,
WARNING could result in minor or moderate injury.
DANGER indicates a hazard with a high level or medium level of risk which,
DANGER if not avoided, could result in death or serious injury.

2
Documentation Obtaining
You can visit http://enterprise.huawei.com to obtain the latest product documentations. Choose Support >
Product > Enterprise Networking > Datacom Network > WLAN > Product Documentation, and then select
the document of a specified version.

NOTE
You can select the document as required. For example, if you want to obtain AP7110DN-AGN documents,
select AP7110DN-AGN.

Technical Support
If you have trouble in locating or rectifying faults during maintenance or troubleshooting by following
instructions in this document, contact the Huawei customer service center (CSC) for help.
• Tel: 4008229999
You can also visit http://enterprise.huawei.com, click Contact Us in the lower area of the page, and select the
country to obtain contact information about Huawei local office.

3
Change History
Changes between document issues are cumulative. Therefore, the latest document issue contains all the
changes in previous issues.

Change in Issue 01 (2012-10-31)

Initial commercial release.

4
 Device Introduction

The Huawei AP series indoor wireless LAN access point provides eight models: AP3010DN-AGN,
AP5010DN-AGN, AP5010SN-GN, AP6010DN-AGN, AP6010SN-GN, AP6310SN-GN, AP7110DN-AGN,
and AP7110SN-GN. The indoor AP features high reliability, high security, simple network deployment,
automatic AC discovery and configuration, and real-time management and maintenance.
The APs are recommended in scenarios where the building structure is simple and the building area is
small, have a high density of users, and have high capacity demands, for example, small-scale meeting
rooms, bars, and entertainment places. The APs can be flexibly deployed.

Table 1 lists the dimensions and weights of indoor APs.

Table 1 Dimensions and weight

Model Dimensions Weight

AP3010DN-AGN
AP5010DN-AGN
AP5010SN-GN 180mm×180mm×50mm（W×D×H） 0.4kg
AP6010DN-AGN
AP6010SN-GN
AP6310SN-GN 130mm×150mm×35mm（W×D×H） 0.6kg

AP7110DN-AGN 200mm×200mm×45mm（W×D×H） 0.95kg

AP7110SN-GN 200mm×200mm×45mm（W×D×H） 0.92kg

Table 2 Interfaces on indoor APs

AP3010DN-AGN
AP5010DN-AGN
AP5010SN-GN
AP6010DN-AGN
AP6010SN-GN DC 12V Default ETH/PoE Console

1 2 3 4 5

AP6310SN-GN

6 4 3 2 1 8

5
 Device Introduction

Table 2 Interfaces on indoor APs

AP7110DN-AGN
Console ETH/PoE Default DC 12V

7 8 4 3 2 1 5 6

AP7110SN-GN
Console ETH/PoE Default DC 12V

8 4 3 2 1 5 6

Table 3 Interfaces on indoor APs

No. Name Description

1 DC 12V Connected to the power adapter.

2 Default Press and hold down the Reset button for 3 seconds to restore the
factory settings and restart the AP.
10/100/1000M port, which connects to the wired Ethernet. The port
3 ETH/PoE can connect to a PoE switch or a PoE power supply to provide
power for APs.
4 Console Connected to the maintenance terminal for device configuration and
management.
5 Security slot Connected to the security lock.

6 2.4 GHz
A port connected to the 2.4 GHz antenna.
antenna port
7 5 GHz antenna
A port connected to the 5 GHz antenna.
port
8 Connect the ground cable to the AP with a ground screw.
Ground screw

6
 Installation Preparations

1. Safety Precautions

WARNING

Only the qualified personnel are permitted to install and remove the device and its accessories.
Before installation and operation, read the safety precautions carefully.

 Take proper measures to prevent injuries and device damage.

 Place the device in a dry and flat position away from any liquid and prevent the device from
slipping.
 Keep the device clean.
 Do not put the device and tools in the aisles.

2. Installation Environment Check

Before installation, verify that the device runs in a favorable environment.
The table lists requirements on the environment that a device works in, including the temperature,
humidity, altitude, and pressure.

Table 4 Requirements on the environment

Item Range

AP3010DN: -5℃～+45℃

AP5010DN&SN: -5℃～+45℃
Temperature AP6010DN&SN: -5℃～+45℃

AP6310SN: -5℃～+45℃

AP7110DN&SN: -5℃～+55℃

Relative humidity 5% to 95%

Altitude -60 m to +4000 m

Pressure 70 kPa to 106 kPa

7
 Installation Preparations

3. Device Accessories
The following accessories are delivered together with indoor APs:

AP6010DN&SN, AP6310SN,
AP3010DN, AP5010DN&SN: AP7110DN&SN: sheet metal wall-
plastic wall-mounting bracket mounting bracket Expansion screws

4. Installation Tools
To install indoor APs, prepare the following tools:

Maker Phillips screwdriver Flat-head screwdriver

Hammer drill Utility knife COAX crimping tool

Diagonal pliers RJ45 crimping tool Wire stripper

Network cable tester Multimeter Measuring tape

Ladder Adjustable wrench Hammer

ESD gloves Level 6mm drill bit

8
 Installing the AP

1. Installation Flowchart
Figure 1 Flowchart for installing an AP
Start

Check before
installation

To a T-rail Determine the Against the ceiling

installation location

Against the wall

Fix the wall-mounting Fix the wall-mounting Fix the wall-mounting

bracket to a T-rail bracket against the wall bracket against the ceiling

Install the AP

Connect the
security lock to
the lock hole

Connect the
cable

End

2. Checking Before Installation

Unpack the package. Ensure that all the items listed in the packing list are included in the carton. If
any item is missing, contact the supplier.
Table 5 Packing list

No. Item Quantity Unit

1 AP device 1 PCS
2 Power adapter (optional) 1 PCS
3 Sheet metal wall-mounting bracket 1 PCS
4 Plastic wall-mounting bracket 1 PCS
5 2.4 GHz antenna 3 PCS
6 5 GHz antenna 3 PCS
7 Expansion screws 3 PCS
8 OT terminals 2 PCS
9 Quick Start 1 PCS

NOTE
 The AP6010, AP6310, and AP7110 series have sheet metal wall-mounting bracket delivered
with them, while the AP3010 and AP5010 series have plastic wall-mounting bracket delivered
with them.
 Three 2.4 GHz antennas and three 5 GHz antennas are contained in the AP7110DN-AGN
carton, and three 2.4 GHz antennas are contained in the AP7110SN-GN carton. Cartons of
other models do not contain antennas.
 Only the AP6310 series and AP7110 series have OT terminals delivered.

9
 Installing the AP

3. Determining the Installation Position

When determining the AP installation position, comply with the following rules:
 Try to reduce the number of obstacles, such as walls, between the AP and user terminals.
 Install the AP away from electronic devices that can interfere the radio signal or make noises,
such as the microwave oven.
 Install the AP in a hidden position that does not affect working and living of residents.
 Install the AP away from water, drippings, and dews, and prevent water on cables from flowing
into the device along the cable.
Indoor APs can be mounted against the wall, the ceiling, or to a T-rail. The APs are generally
mounted against the wall or ceiling using sheet metal wall-mounting bracket; therefore, the
installation position is determined by the site survey. The cabling end of the device must be at least
200 mm away from the wall. Figure 2 shows the space requirements.
Figure 2 Installation against the wall

Celling

Wall

Floor

Figure 3 Installation against the ceiling

Celling

Wall

Floor

10
 Installing the AP

4. Installing the AP

NOTE
 The AP3010DN-AGN, AP5010DN-AGN, and AP5010SN-GN have plastic wall-mounting bracket
delivered with them, so they can only be wall mounted. The AP6010DN-AGN, AP6010SN-GN,
AP6310SN-GN, AP7110DN-AGN, and AP7110SN-GN have sheet metal wall-mounting bracket
delivered with them, so they can be wall mounted, ceiling mounted, or T-rail mounted indoors.
 The procedures for installing all models of indoor APs are the same unless otherwise stated. The
following figures use the AP7110DN-AGN as an example.

 Against the Wall

You need the sheet metal wall-mounting bracket and expansion screws to install the indoor AP
against the wall. The procedures are as follows:
1. Fix the wall-mounting bracket to the wall, 2. Use 6 mm drill bit to drill 25mm to 30 mm
adjust the installation position, and use the deep holes in the drilling positions. Hammer
marker to mark the drilling positions where the expansion tubes into the holes until the
expansion bolts are installed. expansion tubes are embedded into the wall.

59mm
1 2

UP UP 25mm~30mm
85mm

4. Align the holes at the rear side of the AP with

the hooks on the bracket and hang the AP on
the bracket. Hold the AP with one hand and
press the AP downwards with another hand to
3. Fix the wall-mounting bracket to the wall, secure the AP on the wall.
use the Phillips screwdriver to fasten three
self-tapping screws into the expansion tube.
1

11
 Installing the AP

 Against the Ceiling

1. Fix a clip holder at the rear side of the AP with two M3*6 screws. The wall-mounting bracket is
fixed at the ceiling, and the AP is hung on the bracket. The clip holder prevents the AP from
dropping.

1 2

1. M3*6 screw 2. Clip holder

2. Remove the ceiling, determine locations of mounting holes based on the distance between two
installation holes, use the hammer drill to drill holes, and fix the wall-mounting bracket to the ceiling.

1 2

UP UP

35mm

1. Ceiling 2. Adjustable buckle 3. M4*30 screw

The screws provided for ceiling-mounting of APs are 30 mm long and can be used to fix an AP on a
ceiling not thicker than 15 mm. To install APs on thicker ceilings, customers need to purchase
longer screws.

12
 Installing the AP

3. Align the cucurbit holes at the rear side of the AP with four screws on the wall-mounting bracket
and secure the AP.

5G 5G 5G

 To a T-rail

1. Fix a clip holder at the rear side of the AP with two M3*6 screws. For details, see step 1 in
Against the Ceiling.
2. Remove the two ceilings around the T-rail. Use screws to fix the adjustable buckle to the sheet
metal wall-mounting bracket, hook the adjustable buckle to the T-rail, and secure the screw on
the adjustable hook to fasten the wall-mounting bracket and T-rail.
1

1. T-rail 2. Adjustable 3. M3*6 screws

3 buckle

3. Align the cucurbit holes at the rear side of the AP with the four hooks on the bracket. Ensure
that the AP is installed in the correct direction; otherwise, the clip holder cannot fix the AP.

5G 5G 5G

Ensure that the AP is correctly installed on the wall-mounting bracket and there must be 20 cm
space above and around the AP for maintenance.

13
 Installing the AP

5. Installing the Security Lock

NOTE
You need to purchase the security lock.

The device provides a lock hole. You can lock the device to an immovable object to ensure security.
The detailed procedures are as follows:
1) Fix the cable of the security lock to a fixed object around.
2) Plug the locking piece into the security keyhole on the device and lock it.

1. Lock hole 2. Security lock

6. Connecting Cables
Table 6 Appearance of indoor APs (front view)

AP3010DN-AGN
AP5010DN-AGN
AP5010SN-GN
AP6010DN-AGN
AP6010SN-GN
DC 12V Default ETH/PoE Console

5 4

AP6310SN-GN

2 4 5 3

14
 Installing the AP

Table 6 Appearance of indoor APs (front view)

AP7110DN-AGN
Console ETH/PoE Default DC 12V

1 3 4 5 2

AP7110SN-GN

Console ETH/PoE Default DC 12V

3 4 5 2

Table 7 Cables of indoor APs

No. Cable Description

1 5 GHz antenna cable Connects to the 5 GHz antenna for transmitting and receiving signals.

2 2.4 GHz antenna cable Connects to the 2.4 GHz antenna for transmitting and receiving signals.

3 Connects to the ground cable, with the M4 end connected to the ground
Ground cable
cable and M6 end connected to the protection ground.

• The network cables used are category-5 twisted pairs.

• If the AP needs to connect to the Ethernet, ensure that the
4 Network cable Ethernet cable is working properly. If the Ethernet cable is not
working properly, for example, RJ45 connectors are short-
circuited, the AP may fail to be powered on or fail to work. Before
connecting an Ethernet cable to the AP, use the cable test tool to
check whether the cable is qualified. If the cable is unqualified,
replace it.
Power adapter • The AP supports PoE power supply and DC power supply.
5 12 V DC • Use the power adapter attached with the AP; otherwise, the AP
maybe damaged.

Requirements for making a network cable:

 Cut the cable of proper length based on the distance between the AP and the PSE device, peel
the insulation on both ends of the network cable, and crimp the wires to RJ45 connectors.
 Connect RT45 connectors to the network cable tester to test cable connectivity. The following
shows the pin assignment.

15
 Installing the AP

Table 8 Pin assignment

X1 Pin Wire Color X2 Pin

1 White and orange 1
2 Orange 2
3 White and green 3
4 Blue 4
5 White and blue 5
6 Green 6
7 White and brown 7
8 Brown 8

NOTE
 The antennas of AP6310SN-GN, AP7110DN-AGN and AP7110SN-GN used must comply with local
laws.
 In North America or other regions that Require FCC certification, AP6310SN-GN must use W5030H
antennas from Pulse. AP7110DN-AGN and AP7110SN-GN must use SL15870A or TT-2403-6W1
antennas.
 When using AP6310SN-GN Aps to replace WA633SNs, you need to prepare adapters, such as
SMA-to-N type adapters (figure a and b). Alternatively, make new feeder lines matching the connectors
of AP6310SN-GN Aps (figure c).
a b c

 The service network cable cannot be connected to the console port. Otherwise, the AP may be
damaged when using PoE power supply.
 Standard RJ45 connectors are used on network cables for the AP5010 series.
 Bending the antenna may hurt your hands, so exercise caution when you install the antenna on
the AP7110 series.
 See the following figure to connect network cables to the AP6010 series APs.

16
 Power-on

The indoor AP supports the DC power supply and PoE power supply. You can select the power supply
mode as required.
1. Checking Before Power-on
After the AP installation is complete, you should check the following items before power-on:
 When the DC power supply is used, ensure that the DC power supply is properly grounded.
 When the PoE power supply is used, ensure that the PoE power supply is properly grounded.

 Indoor APs can be either powered on by the PoE or DC power supply.

 Do not frequently power on and off an AP.

2. Indicator Status
Table 9 Indicator status of the AP3010DN-AGN, AP5010SN-GN, AP5010DN-AGN, AP6010DN-
AGN and AP6010SN-GN

Indicator Color Status Type Description

• When the system is being powered on, the

Default indicator is steady green.
Green Steady on status • When the system software is running, the
indicator status depends on the software
running result.
The system is running properly, and the
0.5Hz Ethernet connection is correct, and STAs are
associated with the AP.
Green Running
The system is running properly, and the
0.2Hz Ethernet connection is correct. However, no
user connects to the AP.
Green 4Hz Alarm The CAPWAP link is disconnected during an
upgrade.
A fault that affects services has occurred and
cannot be rectified automatically. For
Red Steady on Error example, the system fails to load the DRAM
or system software. The fault needs to be
rectified manually.

17
 Power-on

Table 10 Indicator status of the AP6310SN-GN

Indicator Information SYS Link Wireless Description

Type
Steady NA NA The device is being started.
green
Startup status
Blinking NA NA The system is working properly.
green

Steady NA NA The system fails to load the DRAM

red or system software.
The system is working properly.
Off However, the Ethernet is not
connected. Radios are disabled
and no user is connected to the AP.
0.5Hz Off
The system is working properly, but
Blinking the Ethernet is not connected. The
green AP has wireless users connected
and is transmitting data. The
indicator blinks more quickly when
more packets are being transmitted.
The system is working properly, the
Off Ethernet is connected, and radios
Running and are disabled. The indicator blinks
connection more quickly when more data is
Steady being transmitted.
0.5Hz or
Blinking The system is working properly,
green Blinking and the Ethernet is connected. The
green AP has wireless users connected
and is transmitting data. The
indicator blinks more quickly when
more packets are being transmitted.

18
 Power-on

Table 11 Indicator status of the AP7110SN-GN and AP7110DN-AGN

Information SYS Link Wireless Description

Type
Steady NA NA The device is being started.
green
Startup
status Blinking NA NA The system is working properly.
green

Steady NA NA The system fails to load the DRAM or system

red software.
The system is working properly. However, the
Off Ethernet is not connected. Radios are disabled
and no user is connected to the AP.
The system is working properly, but the Ethernet
Blinking is not connected. The AP has wireless users
green connected to the 2.4 GHz band and is
0.5Hz Off transmitting data. The indicator blinks more
quickly when more packets are being transmitted.
The system is working properly, but the Ethernet
Blinking is not connected. The AP has wireless users
yellow connected to the 5 GHz band and is transmitting
data. The indicator blinks more quickly when
Running and more packets are being transmitted.
connection
Blinking The system is working properly, but the Ethernet
green and is not connected. The AP has wireless users
yellow connected to the 2.4 GHz and 5 GHz bands and
alternately is transmitting data.
The system is working properly, the Ethernet is
Off connected, and radios are disabled. The indicator
blinks more quickly when more data is being
transmitted.
The system is working properly, and the Ethernet
0.5Hz Steady or Blinking is connected. The AP has wireless users
Blinking green connected to the 2.4 GHz band and is
green transmitting data. The indicator blinks more
quickly when more packets are being transmitted.
The system is working properly, and the Ethernet
Blinking is connected. The AP has wireless users
yellow connected to the 5 GHz band and is transmitting
data. The indicator blinks more quickly when
more packets are being transmitted.
Blinking The AP has wireless users connected to the 2.4
green and GHz and 5 GHz bands and is transmitting data.
yellow The indicator blinks more quickly when more
alternately packets are being transmitted.

19
 Logging In to the AP

After an AP is powered on, you can log in to the AP using the following methods.
1. Logging In to the AP Through the Console Port
2. Logging In to the AP Using Telnet

1. Logging In to the AP Through the Console Port

This section describes how to log in to the AP through the console port. After logging in to the AP,
you can configure the AP using commands.
Procedure
Step 1 Connect a PC to the AP with a console cable. Connect the RJ45 connector to the console port
of the AP and connect the DB9 connector to the serial port of the PC.
Step 2 Run the terminal emulation program on the PC. For example, to open the HyperTerminal
of Windows XP on the PC, choose Start > Programs > Accessories > Communications >
HyperTerminal. Enter the name of the new connection in the Name text box and click OK,
as shown in Figure 1-1.

Figure 1-1 Setting up a connection

Step 3 Select the serial port used on the PC and click OK, as shown in Figure 1-2.
Figure 1-2 Selecting the connected port

20
 Logging In to the AP

Step 4 Click Restore Defaults, select 9600 bit/s from the Bits per second drop-down list box, and
click OK, as shown in Figure 1-3.

Figure 1-3 Setting communication parameters

Step 5 Press Enter on the subsequent dialog boxes until the command line prompt of the user
view, such as <Enterprise AP>, is displayed.

You can run commands to configure the AP. Enter a question mark (?) whenever you need
help.

----End
2. Logging In to the AP Using Telnet
This section describes how to log in to the AP using Telnet. After logging in to the AP, you can
configure the AP using commands.
Procedure
Step 1 Connect a PC to the uplink port of the AP with a network cable.
Step 2 Configure a static IP address for the PC. The IP address must be on the network segment
192.168.0.1/24 (The IP address should not be same as the AP's default IP address
192.168.0.1.) and the subnet mask is 255.255.255.0.
After the configuration is complete, run the ping 192.168.0.1 command on the PC to check
whether the PC can be pinged. If the ping operation succeeds, the connection is set up
successfully. If the ping operation fails, the connection fails to be set up. Check whether the
network cable works properly.
Step 3 Access the command line window on the PC. For example, if the PC runs Windows XP,
choose Start > Run and enter cmd in the displayed dialog box.
Step 4 Run the telnet 192.168.0.1 command to log in to the AP.
Step 5 Enter the default user name and password admin. If the user view is displayed, you have
logged in successfully.

21
 Logging In to the AP

NOTE
Run the exit command to exit from the Telnet window. When the system fails to exit from the Telnet
window:
 If you logged in to the AP from an AC or a switch, press Ctrl+T to return to the AC or switch view.
This operation does not affect the AP operation.
 If you logged in to the AP from a PC, directly close the Telnet window. This operation does not
affect the AP operation.

22
 Appendix

1. Declaration on Hazardous Substances in Electronic Information Products

Hazardous Substances
Parts
Pb Hg Cd Cr6+ PBB PBDE

Mechanical part O O O O O O

Board/circuit module O O O O O O

Signal cable O O O O O O

Cable connector O O O O O O

Power adapter O O O O O O

Auxiliary equipment O O O O O O

O: Indicates that the concentration of the hazardous substance contained in all the homogeneous
materials of this part is below the limit requirement of the SJ/T 11363-2006 standard.
X: Indicates that the Concentration of the hazardous substance contained in all the homogeneous
materials of this part is above the limit requirement.

2. Qualification Card

Qualification Card

PASS

23
 Appendix

3. Warranty Card

Warranty Card
Thank you for choosing HUAWEI Technologies Co., Ltd-a leading telecom solution provider. To get better services,
please read this warranty card carefully, fill in the required information and preserve this card in good condition.

Your Name
Address/Postal Code
Telephone
Product Type
Product Serial Number.
Purchase Date.
Invoice Number.
Dealer's Name
Dealer's Address/Telephone

Preserve well. No reissue

Dealer's Seal:
Limited Warranty
Subject to the exclusions contained below, Huawei Technologies Co., Ltd. (hereinafter referred to as Huawei) warrants
its access terminals (“Products”) to be free from defects in materials and workmanship under normal consumer usage
for one year from the date of purchase of the product ("Warranty period"). During the warranty period, a Huawei
authorized service partner shall remedy defects in materials and workmanship free of charge.
Special Notice:
1. The warranty card shall be applicable only after being stamped by the dealer.
2. The warranty card must be preserved in good condition and free of any scratch or alteration.
3. To claim such service for defects that are not included in the following exclusion terms, the warranty card and
the invoice that records the product serial number shall be presented to a Huawei authorized service partner.
Exclusions:
In any of the following cases, the warranty card becomes unenforceable or inapplicable without prior notice:
1. The defects are caused by improper handling in transportation and assembly.
2. The defects are caused by the fact that the product is dismantled or altered by anyone that is not from a
Huawei authorized service partner.
3. The defects are caused by the fact that the product is used in a harsh environment that is not suitable for the
operation of the product.
4. The defects are caused by any force majeure including but not limited to fire, earthquake, lightning and tsunami.
5. The defects are caused by the fact that the product is used or handled improperly, roughly or not as instructed in
the applicable User Guide.
6. The normal wear and tear, including but not limited to the normal wear and tear of the shell and the power module,
shall not be covered by the limited warranty.
7. The warranty card is altered or illegible, or the product serial number recorded on the warranty card is inconsistent
with the actual one imprinted or labeled on the product.
In any case that is not covered by this limited warranty or should the warranty expire, Huawei shall charge for the
service(s) claimed for the products if the product is still remediable.
Huawei preserves the right for interpretation of this limited warranty.

Huawei Technologies Co., Ltd.

Huawei Industrial Base, Bantian, Longgang,
Shenzhen 518129, People's Republic of China
http://enterprise.huawei.com

24