Scribd
Upload
9 views3 pages

HA EEC2210 Power Electronics-1

This document outlines a home assignment for B.Tech. 4th semester students focusing on Power Electronics, specifically covering various problems related to converters, rectifiers, and thyristors. The assignment includes calculations for average output voltage, rectification efficiency, voltage ripple factor, and other related electrical parameters across different circuit configurations. Each question is designed to assess the understanding of power electronics concepts and their practical applications.

Uploaded by

stronggirlhacker
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
9 views3 pages

HA EEC2210 Power Electronics-1

This document outlines a home assignment for B.Tech. 4th semester students focusing on Power Electronics, specifically covering various problems related to converters, rectifiers, and thyristors. The assignment includes calculations for average output voltage, rectification efficiency, voltage ripple factor, and other related electrical parameters across different circuit configurations. Each question is designed to assess the understanding of power electronics concepts and their practical applications.

Uploaded by

stronggirlhacker
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

SN B.Tech.

4th Sem 2022-23 MM


EEC2210 (Power Electronics-1)
HOME ASSIGNMENT (CO3 and CO4)
MM=15
1 A 1 phase full converter supplied form 220V, 50Hz, the load consists of R = 10 ohm 0.5
large inductance to maintain continuous conduction for a firing angle of 450 determine
(a) Average output voltage & current
(b) Average & RMS values of SCR currents
(c) IPF
2 A single phase transformer, with a secondary voltage of 230V, 50Hz, delivers power to 0.5
load R=10 ohm through a half-wave controlled rectifier current. For a firing angle delay
of 600. (a) the rectification efficiency
(b) form factor
(c) voltage ripple factor
(d) TUF (e) PIV of Thyristor?
3 In the circuit shown in fig, L is large and the average value of 'i' is 100A. 0.5
The thyristor is gated in the …………half cycle of 'e' at a delay angle the equal to —

4 Consider a phase — controlled converter shown in the figure. The thyristor is fired at an 0.5
angle a in every positive half cycle of the input voltage. If the peak value of the
instantaneous output voltage equals 230 V, the firing angle alpha is close to?

5 A half wave thyristor converter supplies a purely inductive load as shown in figure. If 0.5
triggering angle of the thyristor is 1200 the extinction angle will be

6 In the following circuit, if firing angle is 900. Find average output voltage 0.5
7 The circuit in figure shows a full wave rectifier. The input voltage is 230 V (rms) single 0.5
phase ac. The peak reverse voltage across the diodes D1 and D2 is

8 A fully controlled thyristor converter (RL load) is fed from a single-phase source. When 0.5
the firing angle is the dc output voltage of the converter is 300V. What will be the output
voltage for a firing angle of 600, assuming continuous conduction?
9 In the single phase diode bridge rectifier, the load resistor is R= 50 ohm. The source 1
voltage is V 200sinwt, where w= 2pix 50 radians per second. The power dissipated in the
load resistor R is
10 Draw output voltage & current waveforms for the following circuit, when alpha = 120 1
deg, 90 deg, 30 deg

11 A single phase fully bridge converter supplies a load drawing constant and ripple free 1
load current. If the triggering angle is 300, the input power factor will be
12 A three - phase aceto-dc diode bridge rectifier is supplying from a three - phase, 440V 1
source. The rectifier supplies a purely resistive load. The average dc voltage across the
load will be………..V
13 The circuit is figure shows a 3 phase half wave rectifier. The source is a symmetrical, 3 1
phase four — wire system. The line to line voltage of the source is v The supply
frequency is 400 Hz. The ripple frequency at the output is
14 A single phase fully controlled the thyristor bridge ac — dc converter is operating at a 1
firing angle of 250 and on overlap angle of 100 constant dc output current of 20 A. The
fundamental power factor (displacement factor) at input ac mains is?
15 A solar cell of 350 V is feeding power to an ac supply of 440 V, 50 Hz through a 3phase 1
fully controlled bridge converter. A large inductance is connected in the dc circuit to
maintain the dc current at 20 A. If the solar cell resistance of 0.50, then each thyristor
will be reverse biased for a period of?
16 A three phase fully controlled bridge converter is feeding a load drawing a constant and 1
ripple free load current of 10 A at a firing angle of 300. The approximate Total harmonic
Distortion (% THD) and rms value of fundamental component of the input circuit will
respectively be?
17 A 3 — phase fully controlled bridge converter with fee wheeling diode is fed from 400 1
V, 50 Hz AC source and is operating at a firing angle of 600. The load current is assumed
constant at 10A due to high load inductance The input displacement factor (IDF) and the
input power factor (IPF) of the converter will be
18 In a 3-phase semi-converter, for firing angle less than or equal to 600 freewheeling diode 1
conducts for:
19 A three pulse converter is feeding a purely resistive load. What is the value of firing 1
delay angle u, which dictates the boundary between continuous and discontinuous mode
of current conduction ?

You might also like