Total No. of Questions : 8] SEAT No.

8
23
PB3806 [6262]-66 [Total No. of Pages :2

ic-
tat
T.E. (Electrical Engineering)

5s
ADVANCED MICROCONTROLLER AND EMBEDDED

5:0
02 91
SYSTEMS

9:4
0
(2019 Pattern) (Semester- I) (Elective-I) (303145A)

40
8/0 13
0
Time : 2½ Hours ] [Max. Marks : 70
5/2
.23 GP

Instructions to the candidates:

E

1) Solve Q.1 or Q.2, Q.3 or Q.4, Q.5 or Q.6, Q.7 or Q.8.

82

8
C

23
2) Neat diagrams must be drawn wherever necessary.

ic-
3) Figures to the right indicate full marks.
16

tat
4) Assume Suitable data if necessary.
8.2

5s
5) Use of non-programmable calculator is allowed.
.24

5:0
91
49

9:4
Q1) a) List the step for compare mode programming of CCP module of PIC18.
30
40

[4]
01
02

b) Explain bit configuration of CCP1CON. [6]

5/2

c) Write a C program to create 2 KHz PWM frequency with 75% duty

GP

cycle on CCP1 pin. Assume XTAL = 10Mhz. [8]

8/0
CE

OR
82

8
23
Q2) a) Describe programming steps of PWM mode. [4]
.23

b) Explain how time period and duty cycle is set for generation of a
ic-
16

tat
waveform using PWM mode of CCP module. [6]
8.2

5s

c) Write a program to generate a square wave with frequency 10 kHz and

.24

5:0

50% duty cycle on the CCP1 pin, use Timer1. [8]

91
49

9:4
30

Q3) a) Differentiate between Interrupt method and polling method. [3]

40

b) Explain interrupt structure of PIC 18 with neat diagram. [6]

01
02

c) Write a C program to toggle an LED connected to pin RB7 on occurrence

5/2
GP

of an interrupt INTO. [8]

8/0

OR
CE
82

Q4) a) Explain use of INTOIF in INTCON. [3]

.23

b) What the steps in executing an interrupt. [6]

16

c) Write a program to generate a square wave that is half the frequency of

8.2

signal applied at INTO on PORTB.5. [8]

.24
49

P.T.O.
Q5) a) Which bits are used to set the conversion time of ADC? [4]

8
23
b) Explain bit configuration of ADCON0. [6]

ic-
tat
c) Write a C program to get data from Channel 0 (AN0) using ADC interrupt

5s
and displays the result on PORTC and PORTD. [8]

5:0
02 91
OR

9:4
0
Q6) a) State the features of ADC of PIC18F458. [4]

40
b)
8/0 13
State the Sensors used for temperature measurement. Draw flow chart
0
5/2
for temperature measurement using ADC of PIC 18. [6]
.23 GP

c) With the help of interfacing diagram explain how PC microcontroller can

E
82

be used to measure temperature using LM35. [8]

8
C

23
ic-
16

Q7) a) Explain importance of TSR in serial communication. [3]

tat
8.2

5s
b) Write a program for PIC18 to transfer the letter ‘T’ serially at the baud
.24

5:0
rate of 9600, continuously. Assume XTAL = 10MHz. [6]
91
49

9:4
c) Draw and explain Serial communication USART transmit block diagram.
30
40

[8]
01
02

OR
5/2
GP

Q8) a) Explain how 8 and 9 bit data is transmitted in serial communication? [3]
8/0
CE
82

8
b) Write down programming steps to transfer data serially. [6]

23
.23

ic-
c) What are the steps for SPI read and write protocol for single byte? [8]
16

tat
8.2

5s
.24

5:0


91
49

9:4
30
40
01
02
5/2
GP
8/0
CE
82
.23
16
8.2
.24
49

[6262]-66 2