*********************************************************

Welcome to TITAN series OLT of ZTE Corporation

*********************************************************
Login at 18:05:18 05-20-2025 from 103.246.64.235 through TELNET.
The last successful login was performed at 13:11:50 05-19-2025 from 110.44.127.130
through TELNET. Afterwards, 0 authentication failure occurred.
BRT-KATAHARI-ZXAN-20.61#show ?
aaa-accounting-template Show AAA accounting template configuration
aaa-authentication-template Show AAA authentication template configuration
aaa-authorization-template Show AAA authorization template configuration
access-list Information for access-list
accounting Show RADIUS accounting information
acl ACL configuration
admin-state Show card admin-state information
alarm Show alarm information
all Show all forwarding route
anti-user-side-icmp Show anti-user-side-ICMP switch
aps Show APS information
arp Show ARP table
asa-card-mng-ip Show asa card info
authen-restriction Show information about authen-restriction users
authentication-cert Show authentication-cert
authentication-info Show authentication information
auto-write Show auto-write information
backboard Show backboard information
battery Show battery
bfd Show BFD information
bgp Show BGP information
blade Show blade information
blade-ifconfig Show blade ifconfig info
blade-manage Show blade mange config
boot-firmware Show boot-firmware information
bootmode show bootmode authentication
card Show card information
card-clock Show card clock information
card-exception Card-exception
card-upgrade-order Show card upgrade order
certification Show certification
ces
cfm Show CFM information
check Show check information
chip-signal-policy Show chip-signal-policy
clients Show network access online clients
clock Show current system clock
cmdgroup Show cmdgroup
collection Show collection information
color-te Show color-TE brief
configuration Show configuration information
configuration-load-mode Show configuration load mode
configure Show configure exclusive
console Show console info
contact Show system administrator's contact information
control-panel Show control panel configure information
control-protocol Show control-protocol information
controlplane-link show controlplane-link statistics
controlplane-port show controlplane-port status
corrosion-circuit Show corrosion-circuit slot
cps Show CPS information
cpu Show CPU information
cpualarm Show CPU alarm granularity
cpuload-threshold Show threshold of cpuload
custom Enter customized mode
data-link-layer Show data link layer information
debug Show state of each debugging option
debug-timer Show time of turning off debug option
device Show device information
devid Show device identity
dhcp-support-user-relay Dhcp-Support-User-Relay
dhcp-test Show dhcp-test information
dhcpv4-l2-relay-agent Show dhcpv4-l2-relay-agent information
dhcpv6-l2-relay-agent Show dhcpv6-l2-relay-agent information
dhcpv6-l2-relay-mode Show dhcpv6-l2-relay-mode information
diag-info Collect diagnose information
diaglog Show diaglog information
digital Show digital signature
discard-packet-mode show discard-packet-mode
ecmp-mode Show ECMP mode
env-switch Show environment switch
epm-config Show Epm information
epon Show EPON config information
equipment Show equipment information
erps Show erps
error Show error information
eth-switch Show eth-switch configuration
ethernet-oam Show Ethernet OAM information
evpn Show EVPN information
fan Show the fan information
fan-amend Show fan-amend
fc Show FC information
filesystem Show filesystem of the operable device
gpon Show GPON information
harddisk-firmware Show harddisk-firmware
hardware-state Show hardware self check result information
health-report-threshold Show health-report-threshold config
his-performance His-performance config
history Show the session command history
holdtime Show hold time of port
hostname Show system's network name
hotkey Show information about terminal lines
ifdescr Show ifDescr configuration
igmp Show IGMP global information
igmp-test Show igmp-test
images Show images briefly
ingress-outer-tpid-filter show global tpid filter
inner-port Show inner-port information
install Show information of install packages
integrality Show file integrality
interface Display interface property and statistics
interface-vlan Show VLAN configuration of VLAN interface
interface-vnd0 Display interface-vnd0 property and statistics
ip Show IP information
ip-service Show ip-service information
ip-source-guard Show ip-source-guard information
ipdr Show IPDR information
ipg Show IPG information of interface
iptv Show information about iptv
ipv4-access-groups Show IPv4 access groups
ipv4-access-lists Show IPv4 access lists
 ipv4-mixed-access-groups Show IPv4 mixed access groups
ipv4-mixed-access-lists Show IPv4 mixed access lists
ipv6 Show IPv6 information
ipv6-access-groups Show IPv6 access groups
ipv6-access-lists Show IPv6 access lists
ipv6-mixed-access-groups Show IPv6 mixed access groups
ipv6-mixed-access-lists Show IPv6 mixed access lists
isis Show IS-IS routing information
issu Upgrade for ISSU
issu-softreboot-mode Show issu-softreboot-mode
keychain Show keychain information
l2vpn Show L2VPN information
l2vpn-statistics Show l2vpn-statistics information
l3switch show L3 interface
l3vpn Show L3VPN information
lacp Show LACP information
lawful-intercept Show lawful flow detail information
license Show license information
link-access-groups Show link access groups
link-access-lists Show link access lists
lldp Show LLDP information
load-mode Show load-mode
local-user Show local user information
location Show location information of system
lock Show lock configuration
logfile Show configure command information
logging Show logging information
logicinterface Show logic interface information
login Show configuration of attack defence
loopback-detection Show loop-detection Status
lsp-group Show the configuration information of LSP-GROUP
module
lst Show lst configuration
mac Show mac information from mainl card
mac-list Show MAC list information
mc-elam Show MC-ELAM information
mc-lag Show mc-lag information
media-monitor Show media monitor information
memory Show memory information
memory-threshold Show threshold of memory
mld Show MLD global information
mld-test Show mld-test
monitor Monitor information
mpls Show MPLS information
mpnat Show mpnat
msvxlan Show msan vxlan information
multi-user Show multi-user information
multicast show multicast data profection
multicast-monitor Show multicast monitor info.
mvlan-translate Show global mvlan trans info.
nd Show IPv6 neighbor discovery information
nd6 Show IPv6 neighbor discovery information
netconf Show NETCONF agent parameters
netconf-engine Show NETCONF engine information
nf-type Show information of NF-type
ngpon Show NGPON information
ntp Show NTP information
odb-switch show odb-switch status
onu-compat Show ONU type compatible information
onu-pnp show onu-pnp config information
onu-type Show ONU type template information
onu-type-if Show ONU type UNI information
openflow Show OpenFlow information
optical-als-info Show port optical-als information
optical-module Show optical-module
optical-module-alarm-ctrl Show optical-module-alarm-ctrl information
optical-module-alarm-profile Show optical-module-alarm-profile
optical-module-class-profile Show optical-module-class-profile
optical-module-firmware Show optical module information
optical-module-history-info Show optical-module-history-info
optical-module-info Show port optical-module information
optical-module-light-status Show optical-module-light-status
optical-module-plug-record Show port optical-module plug and unplug records
optical-module-reserved-class Show optical-module-reserved-class
para-group Show para-group configuration
para-group-bound Show the rules using the para-group
password-dictionary Show password dictionary information
patch Show patch information
patch-func Patch-func-set
perf-brg-if-profile Show brg-if performance alarm profile
perf-eth-if-profile Show EthPort performance alarm profile
perf-eth-olt Show OLT ethernet performance alarm profile
perf-eth-onu Show ONU ethernet performance alarm profile
perf-mac-olt Show OLT MAC performance alarm profile
perf-mac-onu Show ONU MAC performance alarm profile
perf-vlan-profile Show vlan performance alarm profile
performance Show performance config
pid Fan strategy of PID
ping Show ping information
pmap Show pmap relation
pnp Show pnp config
pon Show PON information
pon-alarm Show pon-alarm
pon-association-vlan show pon vlanlist
port-identification Show port-identification information
portal Show portal information
power Show the power information
power-alarm-threshold Power-alarm-threshold
powerboard
pppoe Show pppoe commands
pppoe-filter Show pppoe-filter status
pppoe-intermediate-agent Show pppoe-intermediate-agent information
pppoe-reverse-packet-filter Show pppoe-reverse-packet-filter configuration
pppoe-snooping Show pppoe-snooping information
pppoe-test Show pppoe-test all status and result
priority-mark ACL priority-mark configuration
privilege Show current privilege level
process-memory-threshold Show process-memory-threshold
processor Show processor information
propagate Show propagate information
protection Show PON protection information
pseudo-wire Show the qos profile applied to the pseudo-wire
pw Show PW configuration
pw-list Show pw-list information
pwe3 Show PWE3 information
qos Show QoS information
quick-ping
radius Show RADIUS information
 radius-attribute Show RADIUS attributes supported
radius-resource Show RADIUS resource information
radius-server Show RADIUS server information
read-config Show read-config information
real-acl ACL configuration
redirect Show redirect interface
remote-unit show RU
resource Show resource
resource-profile Show resource-profile
route-map Show route-map information
rsvp Show RSVP
running-config Show current operating configuration
running-config-interface Show running information of interface<interface-
name>
running-config-vrf Show running information of vrf<vrf-name>
safety-speed Safety-speed
security Security information
serdes-for-power Serdes-for-power
serdes-for-temp Serdes-for-temp
serdes-mgmt Serdes management configuration
serdes-state Show serdes-state
service-port Show service port configuration
service-unit-select Show service unit selection information
sf-switch Show sf-switch information
siepon Show SIEPON information
snetconf Show SNETCONF server parameters
snmp Show SNMP information
sockets Show all socket connections information
software Show software information of system
spantree Show STP information
ssh Show SSH information
standard-yang-load Show standard yang model
startrun-backup Show startrun-backup information
startup-config Show startup configuration
statistics Statistics
storage-threshold Show threshold of storage
strong-password-info Show strong password configuration parameters
supervlan Show SuperVLAN parameter
supervlan-pool Show SuperVLAN IP-POOL
supervlan-v6 Show SuperVLAN parameter for IPv6
supervlan-v6pool Show SuperVLAN IPv6-POOL
synchronization Show master-slave synchronization state
system Show mode of switch for ZTP
system-energy-saving-detail Show system energy-saving detail
system-energy-saving-mode Show system-energy-saving-mode
system-monitor Show system-monitor state
system-overheat-threshold Show system overheat threshold
system-reducepower-threshold Show system reducepower threshold
tacacs Show TACACS+ global configuration
tacacs-server Show TACACS+ server configuration
tacacs-server6 Show TACACS+ IPv6 server configuration
tacplus Show TACPLUS group server configuration
tcp Show TCP information
tcp6 Show IPv6 TCP information
te-class-mapping Show TE-CLASS map
te-ecmp-group Show TE-ECMP group information
telemetry Show telemetry information
temperature Show temperature detail information
terminal Show terminal configuration parameters
 this Show current mode configuration
time Show time
time-range Show time range information
time-range-acl Show time-range-acl
tpa Show information of TPA
traffic-limit ACL traffic-limit configuration
traffic-mirror show traffic-mirror info
traffic-stat-enable Show traffic statistics enable information
traffic-stat-value Show traffic-stat-value information
troubleshooting Show troubleshooting information
tunnel-policy Show tunnel policy information
twamp Show TWAMP information
uaps Show UAPS configuration
udp-helper Show udp-helper information
updateepld Show cpld update status
upgrade-state Show upgrade state of issu
user-defined-access-groups Show user defined access groups
user-defined-access-lists Show user defined access lists
user-group Show user group information
user-protocol-access-lists Show user protocol access list
username Show information about registered users
users Show information about terminal lines
vgw Show vgw
vgw-bypass Show vgw-bypass
virtual-mac Vmac information
virtual-network-device Show the virtual network device information
vlan VLAN status
vlan-connect vlan-connect rules
vlan-mark ACL vlan-mark configuration
vlan-share Show shared VLAN list
vlan-validity Vlan-validity status
vnd Show VND information
vnd-resource Show vnd-resource
vport-resource Show vport resource
vrrp Show VRRP information
vxlan Show VXLAN information
wave-channel-group-info Show wdm-pon wave-channel-group-information
wave-channel-information Show wdm-pon wave-channel-information
wpon
wpon-config-speed wpon-config-speed
ztp Show ZTP process information
BRT-KATAHARI-ZXAN-20.61#show

BRT-KATAHARI-ZXAN-20.61(config-if-gpon_olt-1/2/10)#show hotkey
Keystrokes Function
Ctrl-A Move the cursor onto the first character of the current line
Ctrl-C Clear the inputing command line and enter privilege mode, or interrupt
the running command even if the system is busy
Ctrl-D Equivalent with the command of "no debug all"
Ctrl-E Move the cursor to after the last character of the current line
Ctrl-H Same as backspace,clears the charactor before the cursor
Ctrl-K Clear the line after the cursor and the cursor itself
Ctrl-N Same as the down arrow key,search command history backward
Ctrl-O Quit and suspend the session of the current terminal
Ctrl-P Same as the up arrow key,search command history ahead
Ctrl-T Equivalent with the command of "no terminal monitor"
Ctrl-U Clear the entire line currently being typed
Ctrl-W Enter the terminal session suspended before
Ctrl-X Clear the line before the cursor
Ctrl-Z Clear the inputing command line and enter privilege mode, or interrupt
the running command
Esc-B Move the cursor backward one word
Esc-D Clear the word right of the cursor
Esc-F Move the cursor forward one word
Esc-Q Support the input of "?" and "spacebar" for a pair of the key
Esc-U Support the input of "?" and "spacebar" for a pair of the key
Esc-W Clear the word left of the cursor

BRT-KATAHARI-ZXAN-20.61(config-if-gpon_olt-1/2/3)#?
als Set optical module als
association-vlan Configure association-vlanlist of epon_olt
auto-learning Configure ONU auto learn information
bind-onu Configure ONU basic information
blacklist Configure ONU blacklist
cutover Cutover configuration
dba Configure the DBA settings
description Interface specific description
direct-route The SAMGR track configurations of direct route
discover-period Configure the time for discovering new ONU login or
ONU missing
do Do privilege mode command(s)
end Exit to privilege mode
exit Exit from current mode
fec Configure FEC attributes
fiber-distance Configure OLT fiber distance
igmp Configure IGMP interface property
linktrap Configure linktrap status
loopback-detection Configure loopback detection port switch
max-onu-num Configure maximum ONU number
mld Configure MLD interface property
multicast-encrypt Enable/Disable multicast encryption
name Configure alias of the OLT interface
no Negate a command or set its defaults
nop do nothing
onu Configure ONU basic information
onu-action Action for all ONUs under this port
onu-num-alarm-thresh Configure ONU number alarm threshold
onu-sn Enable/Disable ONU SN
optical-module Configure optical-module
optical-module-alarm-profile Load the alarm-thresh-profile
optical-module-part-number Set optical module part number(P/N)
otdr-profile Apply OTDR profile to this interface
perf-clear-current Clear current performance for olt
perf-profile Apply performance alarm profile to this interface
ping Send echo messages
ping6 Send IPv6 echo messages
pnp Enable/Disable plug-and-play ONU function
pon-id Configure the value of PON port identifier
qos Configure the qos parameters
reset Reset GPON OLT interface
resource-id-assign-mode Configure Alloc-ID and Port-ID assign mode
scb-port Configure SCB port
show Show running system information
shutdown Shut down the selected interface
stop Stop show diagnose information
trace Trace route to destination
 trace6 Trace route to destination using IPv6
uncfg-onu-aging-time Configure uncfg ONU aging time of auto learning
BRT-KATAHARI-ZXAN-20.61(config-if-gpon_olt-1/2/3)#

BRT-KATAHARI-ZXAN-20.61(config-if-gpon_olt-1/2/3)#exit
BRT-KATAHARI-ZXAN-20.61(config)#?
Configure commands:
aaa-accounting-template AAA accounting template configuration
aaa-authentication-template AAA authentication template configuration
aaa-authorization-template AAA authorization template configuration
acl Configure Acl
add-card Add a card
admin Admin ac or deactive linecard
alarm Configure the alarm parameters
anti-user-side-icmp Anti-user-side-ICMP switch
aps Configure APS instance
arp Enter ARP configuration mode
arp-oam Configure arp-oam switch
asa-card-mng-ip Configure asa card ip
auto-write Set auto-write disable | enable
banner Terminal line banner
bfd Enter BFD configuration mode
bgp Border gateway protocol (BGP)
card-apply Apply the modify slot file
card-save Save the modify slot file
cfm Enter CFM configuration mode
check Configure intervals of check
check-config-reload Check and revise the specific config file, then auto
reboot
check-revise-config Check and revise the specific config file
chip-signal-policy Set chip signal policy
clear Clear the configuration data
clock Enter clock mode
cmdgroup Set cmdgroup
command-authorization Configure command authorization
config Enter VND configuration mode
configuration Configuration
configuration-load-mode Set configuration load mode
control-panel Configure control panel
control-plane-security Enter CPS configuration mode
control-protocol Configure global protocol's parameters
cpuload-threshold Configure alarm thresholds for CPU load utilization
custom Enter customized mode
debug-redirect Set the parameters of debugmsg
default Configure with the defaults
del-card Delete card
device Set device
dhcp Enter DHCP configuration mode
dhcp-support-user-relay To be confirmed
dhcpv4-l2-relay-agent Configure dhcpv4 layer-2 relay agent global
information
dhcpv6-l2-relay-agent Configure dhcpv6 layer-2 relay agent global
information
dhcpv6-l2-relay-mode Configdhcpv6-l2-relay-mode global info
diaglog Configure diaglog
disable To make inoperative
discard-packet-mode set discard-packet-mode
do Do privilege mode command(s)
 dot1x Enter 802.1x mode
dust-proof Configure dust proof clean cycle
ecmp-mode Set ECMP mode
efm Enter EFM configuration mode
enable To make operative
enable-secret Set the expiration policy for the enable secret
enable-strong-password Set the strength of the enable password
encrypted Configure system administrator's contact information
end Exit to privilege mode
entropy-label Set the entropy label
env-switch
epm Configure epm
epon Enter EPON mode
epon-olt-interface-range Enter epon olt interface range configuration mode
epon-onu-interface-range Enter epon onu interface range configuration mode
erps Erps global status
erps-instance Create erps instance or enter erps configure mode
error Error data relevant configuration commands
esi-list Add a ESI list entry
eth-switch Configure eth-switch operation
ethernet-interface-range Select ethernet interface(s) to configure
eti-list Add a Ethernet Tag Identifier list entry
evpn-irb EVPN IRB parameters
exit Exit from current mode
fan Configure fan speed mode
fan-amend Amend fan speed
flow-profile Configure flow-profile parameters
force-print Force print some character(s) while reaching
terminal width
ftp-client Configure FTP client
gpon Enter GPON mode
gpon-olt-interface-range Enter gpon olt interface range configuration mode
gpon-onu-interface-range Enter gpon onu interface range configuration mode
gr Configure graceful restart ability of Forwarding
Information Base
gre-config Enter GRE tunnel configure mode
health-report-threshold Configure threshold for health report
his-performance Configue history performance
history Configure history commands
hostname Configure system's network name
icmp-config Enter ICMP configure mode
ifdescr Config ifDescr unbind state
igmp Configure IGMP
ingress-outer-tpid-filter Config global tpid filter
interface Select an interface to configure
ip Global IP configuration subcommands
ip-service Config ip-service information
ip-source-guard Config ip-source-guard information
ipdr Enter IPDR mode
ippool-openflow-disconnect Configure IP address pool openflow disconnect
iptv Config iptv information
ipv4 Global IPv4 configuration subcommands
ipv4-access-group Bind IPv4 access list to interface
ipv4-access-list Configure IPv4 access list
ipv4-mixed-access-group Bind IPv4 mixed access list to interface
ipv4-mixed-access-list Configure IPv4 mixed access list
ipv4-rib IPv4 RIB configuration subcommands
ipv6 Global IPv6 configuration commands
ipv6-access-group Bind IPv6 access list to interface
 ipv6-access-list Configure IPv6 access list
ipv6-mixed-access-group Bind IPv6 mixed access list to interface
ipv6-mixed-access-list Configure IPv6 mixed access list
ipv6-rib IPv6 RIB configuration subcommands
ipv6-tunnel-config Enter IPv6 tunnel configure mode
isis ISO IS-IS
isis-compatibility Set IS-IS compatibility
keychain Set keychain
keychain-encryption Set encryption keychain
l2vpn-rd-template Configure L2VPN RD template
lacp Enter LACP configuration mode
language Set language
lawful-intercept Configure acl lawful flow-mirror parameters
line Configure terminal access parameter
link-access-group Bind link access list to interface
link-access-list Configure link access list
lldp Configure LLDP parameters
load-mode Configure load mode of data
location Configure system's location information
logging Modify message logging facilities
login Login configuration
loopback-detection Configure loopback detection switch
lsp-oam Configure LSP-OAM information
lst-group Config lst-group id
mac Configure MAC address parameters
mac-list Add a MAC list entry
mask-data Mask-data from file of startrun.dat
mc-elam-configuration Enter MC-ELAM configuration mode
media-monitor Configure media monitor information
memory-threshold Configure alarm thresholds for memory utilization
mib-compatibility Configure MIB compatibility information
micro_switch_control Enable or disable micro_switch_control
mld Configure MLD
modify-card Modify card
monitor-session Monitor session
mpls Configure MPLS parameters
mpnat Configure mpnat
mspw Configure a Multi-Segment Pseudowire (MSPW) instance
msvxlan Configure msan vxlan information
multi-user Access multiuser
multicast multicast command
mvlan-translate Configure mvlan translate characteristics.
nd Enter ND configuration mode
netconf Modify NETCONF agent parameters
netconf-nacm Enter NACM (NETCONF access control model)
configuration mode
no Negate a command or set its defaults
nop do nothing
nsr NSR service
ntp Configure NTP
nvram Configure NVRAM system
of Enter OpenFlow configuration mode
onu-loopback-test
onu-pnp Into onu-pnp mode
optical-module Optical-module configuration
overheat-protection Configure overheat protection
para-group Configure the acl rule parameter group
patch-func-set Enable patch func
patch-param-set Set patch parameters
patch-timer-set Set patch timers
perf-brg-if Configure a Bridge Port performance profile
perf-eth-if Configure an EthPort performance profile
perf-eth-olt Create PON ethernet OLT performance alarm profile
perf-eth-onu Create PON ethernet ONU performance alarm profile
perf-mac-olt Create PON MAC OLT performance alarm profile
perf-mac-onu Create PON MAC ONU performance alarm profile
perf-vlan Configure an vlan performance profile
performance Performance manage
permit Configure permit port useable
pid PID fan strategy
ping Send echo messages
ping-tcp-server Configure TCP ping server
ping-udp-server Configure UDP ping server
ping6 Send IPv6 echo messages
policy-commit-immediately Configure commit immediately
policy-default-action Configure default action
pon Enter PON mode
pon-alarm Configure pon-alarm
pon-copy Configure pon-copy
pon-interface-range Enter pon interface range configuration mode
pon-onu-mng Enter pon-onu-mng configuration
pon-restore Restore pon copy
port-identification Configure port-identification global information
portal Enter portal mode
power Configure power
power-alarm-threshold Power-alarm-threshold Config
pppoe Pppoe commands
pppoe-diag Configure pppoe-diag status
pppoe-filter Configure pppoe-filter
pppoe-intermediate-agent Configure pppoe-intermediate-agent global status
pppoe-reverse-packet-filter Pppoe-reverse-packet-filter commands
pppoe-snooping Pppoe-snooping commands
prime-key Configure prime key
priority-mark Configure priority mark parameters
privilege Command privilege parameters
process-memory-threshold Set process-memory-threshold
product Enter product manage configuration mode
propagate Configure propagate parameters
pseudo-wire Configure pseudo-wire profile
ptp Enter ptp config mode
pw Configure a PW instance
pw-class Configure pw-class parameters
qos Configure QOS parameters
quick-ping enable/disable quick-ping
radius Configure RADIUS
read-config Read the specific file for batch
redirect Configure redirect parameters
redundancy Configure redundancy interchassis group
remote-unit Ru task configuration
remove Delete the entity but the related entities remain
reset Reset functions
resource-profile configure resource profile name
revert Revert interface configure
route-map Create route-map or enter route-map-seq command mode
route-map-seq-required Route-map sequence required
route-map-trigger-delay Configure route-map trigger delay time
router Enable a routing process
safety-speed Safety-speed Config
security Security configuration
security-service-profile Enter security profile cfg mode
serdes-mgmt
service-type Select a service unit
set-pnp Enable or disable pnp card auto config.
set-serdes-for-power Enable or disable serdes for power Config
set-serdes-for-temp Enable or disable serdes Config
sf-switch Sf switch operation
sftp-client Configure SFTP client
show Show running system information
siepon-onu-mng Enter siepon-onu-mng configuration
snetconf Modify SNETCONF server parameters
snmp-server Modify SNMP parameters
spantree Enter STP config mode
srm Enter SRM configuration mode
srv6 IP SRv6 configuration
ssh Configure SSH server parameters
standard-yang-load Configure standard-yang-load
startrun Startrun file configuration
statistics Statistics
stop Stop show diagnose information
storage-threshold Configure the threshold of the storage
supervlan Enter SuperVLAN configuration mode
syslog Configure the syslog parameters
syslog-server Configure the syslog server parameters
system-energy-saving Set energy-saving mode
system-monitor set system-monitor state
system-user Enter config-system-user mode
tacacs Enable or disable TACACS+
tacacs-client Configure TACACS+ client
tacacs-client6 Configure TACACS+ IPv6 client
tacacs-server Configure TACACS+ server
tacplus Configure TACPLUS client or group server
te-ecmp-group Enter the TE-ECMP-GROUP configuration mode
telemetry Enter telemetry configuration mode
temperature Set system-overheat-threshold
time-range Configure time range table
time-range-acl Configure acl time-range parameters
timestamp Set timestamp
tpa Enter TPA configure mode
tpid Configure TPID
trace Trace route to destination
trace6 Trace route to destination using IPv6
traffic-limit Configure traffic limit parameters
traffic-mirror Configure traffic mirror parameters
traffic-profile Configure traffic profile parameters
traffic-stat-enable Configure traffic statistics parameters
traffic-stat-reset Clear traffic statistics parameters
tunnel-policy Configure a tunnel policy instance
twamp Configure TWAMP parameters
uaps-group Config uaps-group id
udp-helper Enable or disable udp-helper
unicast-service-profile Enter unicast profile cfg mode
upgrade Set card upgrade priority
user-defined-access-group Bind user-defined access list to interface
user-defined-access-list Configure user defined access list
user-protocol-access-list Configure user protocol access list
vgw Virtual gateway
vgw-bypass Vgw-bypass configuration
 virtual-mac Global vmac configuration commands
vlan Vlan commands
vlan-configuration Enter the VLAN configuration mode
vlan-connect Configure vlan connect rule
vlan-mark Configure vlan mark parameters
vlan-validity Configure vlan-validity switch
vnd Configure volt apply resource-profile
vni-list Add a Visual Network Index list entry
vpls Configure a Virtual Private LAN Service (VPLS)
instance
vport Creat vport
vport-interface-range Enter pon interface range configuration mode
vpws Configure a Virtual Private Wire Service (VPWS)
instance
vpws-community Configure a virtual private wire service community
instance
vpws-vxlan Configure a VPWS-VXLAN instance
vrf Configure VPN Routing/Forwarding instance parameters
vrrp Enter VRRP mode
vxlan Enter VXLAN configuration mode
vxlan-tunnel-config Enter VXLAN tunnel configure mode
wdm-pon Enter WDM-PON mode
ztp Enable or disable ZTP function.
BRT-KATAHARI-ZXAN-20.61(config)#

BRT-KATAHARI-ZXAN-20.61(config)#exit
BRT-KATAHARI-ZXAN-20.61#?
Exec commands:
activate Activate local user
alarm-confirm Confirm the alarm by flowid
arp-scan ARP scan function
bfd BFD operations
blade set blade state
blade-ifconfig Set blade ipv4 address
blade-v6ifconfig Set blade ipv6 address
bootmode Bootmode authentication switch
cd Change current directory
cfm Exec cfm function
clear Reset functions
clock Manage the system clock
configure Configure
convert-card Convert-card to p2p or pon
copy Copy from one file to another
cp Copy from one file to another locally
debug Debugging functions
delete Delete functions
devid Set devid
diagnose Enter diagnosis mode
dir List files on a filesystem
disable Turn off privileged commands
dns DNS operations
enable Turn on privileged commands
exit Exit from current mode
file File operation
kick-off Kick off DHCP users
ldp-debug-policy Set LDP debug info policy
license Operate license file
load-optical-module-firmware Load optical module firmware
 local-user Local user
lock Lock configuration
login Login as a particular user
logout Exit from the EXEC
manual-switch Set mc-lag manual switch
memory Memory snapshot functions
mkdir Create new directory
more Display the contents of a file
mount Mounting of storage device for installation
mpls-te MPLS TE AUTO-BW
mtrace Trace reverse multicast path from destination to
source
mtrace2 Trace reverse multicast path from destination to
source
no Negate a command or set its defaults
nop do nothing
odb-switch Set odb-switch enable or disable
package Package log
ping Send echo messages
ping6 Send IPv6 echo messages
power Power on or off the card
pwd Display current working directory
quit Quit from the EXEC
radius RADIUS commands
radius-ping Detect RADIUS server
redundancy Redundancy facility exec commands
reload Perform a restart with force or grace
reload-blade reload blade
remote-unit RU manual action
rename Rename a file or directory
reset Reset dust proof clean timer
restart Restart routing commands
rmdir Remove existing directory
save Save running configuration to text file
set Set functions
show Show running system information
simulate-client Configure simulate-client
ssh Open a SSH connection
ssh6 Open an IPv6 SSH connection
startrun Startrun file operation
stop Stop show diagnose information
switch Switch to the virtual network device by name
telnet Open a telnet connection
telnet6 Open an IPv6 telnet connection
terminal Set terminal line parameters
trace Trace route to destination
trace6 Trace route to destination using IPv6
umount Unmounting of storage device for removal
unlock Unlock
unzip Unzip files
vendor-mode Enter vendor mode
who List users who are logining on
write Write running configuration to zdb or text file
writelog Write log to file
zip Zip files
BRT-KATAHARI-ZXAN-20.61#