Scribd
Upload
5 views2 pages

dynamics

The document outlines various settings and parameters related to voltage control, including undervoltage and overvoltage settings, trip times, and gains for controllers. It specifies thresholds for switching capacitors and reactors, as well as time delays and limits for voltage references. These parameters are essential for managing voltage stability and control in electrical systems.

Uploaded by

MUHAMMADUZAIR RASHID
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLSX, PDF, TXT or read online on Scribd
5 views2 pages

dynamics

The document outlines various settings and parameters related to voltage control, including undervoltage and overvoltage settings, trip times, and gains for controllers. It specifies thresholds for switching capacitors and reactors, as well as time delays and limits for voltage references. These parameters are essential for managing voltage stability and control in electrical systems.

Uploaded by

MUHAMMADUZAIR RASHID
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLSX, PDF, TXT or read online on Scribd
You are on page 1/ 2

1 UVSBmax, max cap U/V limit

0.9 UV1, undervoltage setting 1


0.85 UV2, undervoltage setting 2
0.8 UVT, undervoltage trip setting
1.1 OV1, overvoltage setting 1
1.15 OV2, overvoltage setting 2
1 UVtm1, undervoltage trip time 1
3 UVtm2, undervoltage trip time 2
1 OVtm1, overvoltage trip time 1
3 OVtm2, overvoltage trip time 2
0.05 Xs1, slope/droop
0.05 Xs2, slope/droop
0.05 Xs3, slope/droop
1.05 Vup, up volt break-point for non-linear droop
0.95 Vlow, low volt break-point for non-linear droop
0.01 Tc1, voltage measurment lead time constant
0.05 Tb1, voltage measurment lag time constant
0.01 Tc2, pre-controller lead time constant
0.05 Tb2, pre-controller lag time constant
10 Kpv, prop. gain of SVC PI-controller
50 Kiv, integral gain of SVC PI-controller
0.1 Vemax, voltage error max limit
-0.1 Vemin, voltage error min limit
0.01 T2, thyristor firing sequence control delay
1.5 Bshrt, short-term max. suceptance of SVC
1.2 Bmax, continuous max. suceptance of SVC
-1.2 Bmin, min. suceptance of SVC
5 Tshrt, duration of short-term rating
5 Kps, prop. gain of SSC PI-controller
20 Kis, integral gain of SSC PI-controller
0.1 Vrmax, max. output of slow suceptance control
-0.1 Vrmin, min. output of slow suceptance control
0.01 Vdbd1, steady-state voltage deadband
0.005 Vdbd2, inner deadband
1 Tdbd, recovery time to deadband
0.05 PLLdelay, PLL delay in voltage recovering
0.001 xeps, delta added to the susceptance bandwidth
0.9 Blcs, larger threshold for switching Mechanically Switched Capacitors
0.1 Bscs, smaller threshold for switching Mechanically Switched Capacitors
0.9 Blis, larger threshold for switching Mechanically Switched Reactors
0.1 Bsis, smaller threshold for switching
0.1 Tmssbrk, time for Mechanically Switched SHunt (MSS) breaker to operate
2 Tdelay1, time delay for larger threshold
1 Tdelay2, Time delay for smaller threshold
5 Tout, time MSC should be off before switch back
0.95 Vrefmin, lower DeltaV ref limit
1.05 Vrefmax, upper DeltaV ref limit

You might also like