Two-Channel Intercom Power Supply PS-22

PS-22 Front Panel

F E AT U R E S DESCRIPTION
• Light, small, rugged, and portable, The PS-22 power supply
with carry handle supports two intercom CH
A
On
.25A 250V
RISK OF FIRE - REPLACE
WITH FUSE AS MARKED

WARNING: TO REDUCE THE RISK

channels containing up to OF FIRE OR ELECTRIC SHOCK DO

MAX
• “Intelligent” power sensing Off NOT EXPOSE THIS EQUIPMENT TO
RAIN OR MOISTURE

Term.
30 headset stations or 10

30V, 1A
• Provides system power, line Program
Input

speaker stations. The PS-22

220-240V On

USE ONLY WITH 250V CH Mic

termination, and program feeds FUSES/EMPLOYER

UNIQUEMENT AVEC
B Line

features Clear-Com’s fail-

DES FUSIBLES DE 250V Off
110-120V

for 2-channel system

safe power-supply design
• Automatic short-circuit protection PS-22 Back Panel
for maximum reliability.
and reset In the event of a DC short circuit or current overload, the PS-22’s electronic over-
• “Short” and “Good” power load protection circuit will instantly shut down the DC output to avoid damage.
indicators As soon as the fault condition is removed, the auto-reset circuitry will automati-
• Front-panel “Link” switch to cally restore system power, even under full load conditions. There is no need to
operate as one-channel system disconnect stations to allow the power supply to reset.
The portable PS-22 is capable of delivering 1 amp at 30 volts. Two or more
• Program input with selectable
power supplies can be connected in parallel for increased capacity. In such configu-
channel assignments and individual
rations, the PS-22’s intelligent power-sensing capability enables the system to auto-
level controls
matically reset itself in the event of a DC short or AC power loss anywhere in the
• Can be paralleled with other system, no matter how many power supplies the system contains. You need never
power supplies and main stations disconnect and reconnect remote stations to restore power to the entire system.
for increased capacity or backup The PS-22 provides, in addition to system operating power, two channels of
support intercom. It also provides a convenient front-panel “link” switch to operate as a
• One-amp power supply capacity one-channel system.
• Switchable 115/230 VAC The PS-22 also accepts a balanced program input, selectable for microphone
or line-level signals, that can be sent to either or both channels, mixing with the
• Portable or rackmount
intercom signal.
• UL approved The front panel of the PS-22 includes two program on/off switches and level con-
trols, the channel-link switch, and the “short” and “OK” DC power-status LED.
The PS-22 rear panel provides XLR intercom-line connectors for each channel,
two intercom-line termination switches, an AC-mains power-connector block
with power on/off switch, one XLR program-input connector, and a program
mic/line select switch.
Two-Channel Intercom Power Supply PS-22

S P E C I F I C AT I O N S The PS-22 connects to remote stations with standard, two-conductor shielded

POWER SUPPLY mic cable. With the optional rackmount kit, the power supply can mount in a
Output power: +30 VDC, +-1 V standard 19" equipment rack, requiring only two rack units.
Output Current: 1 amp The PS-22 conforms to the highest standards of reliability and performance,
Reset Current: 1 amp providing trouble-free service over a wide range of environmental conditions.
Hum & Noise: <-70 dBv It can be mounted in an enclosed rack since it can tolerate an ambient tempera-
Station Capacity: 30 headset stations or 10 ture of 120oF without failure.
speaker stations
PROGRAM AMPLIFIER
(Transformerless, balanced differential input)
Input Level,
Mic: -65 dBv
Line: -15 dBv
Input Impedance,
Mic: >1 kΩ REAR-PANEL CONNECTORS DIMENSIONS
Line: 100 kΩ Intercom: (6) XLR-3M (3 per channel) 3" H x 8.12" W x 10" D (76 x 206 x 254 mm)
Frequency Response: 150 Hz - 18 kHz, +-2 dB Program: (1) XLR-3F
WEIGHT
SYSTEM SPECIFICATIONS REAR-PANEL SWITCHES 4.7 lbs. (2.1 kg)
Intercom Line Length: 5,000 ft. maximum Power on/off: 1
Intercom Line Length for Crosstalk <-52 dB: Termination on/off: 2 All specifications are subject to change without notice.
500 ft. maximum Mic/line select for program input: 1 *
0 dBv is referenced to 0.775 volts RMS
Stations Per Intercom Line: 100 maximum
AC POWER REQUIREMENTS
System Frequency Response:
105 - 125/210 - 250 volts, 50 - 60 Hz, 60 VA
150 Hz - 18 kHz, +-2 dB

PS-22 BLOCK DIAGRAM INTERCOM LINE OUTPUT

CHANNEL A
TERM
ON
CURRENT
LEVEL SOURCE
PGM
OFF
LEVEL MIC
SELECT 2 1
LINE
3
BALANCED 1 2
INPUT
PROGRAM PAD A+B
INPUT A+B LINK
3

CHANNEL B
PROGRAM TERM
ON/OFF ON
CURRENT
A B
LEVEL SOURCE
PGM
OFF
2 1
CONTROL LOGIC
3
TO CMOS
SWITCHES

RED GREEN
SHORT OK
POWER ENTRY REGULATED
= ANALOG CMOS SWITCH MODULE WITH POWER SUPPLY 32V
PWR ON/OFF SW

Clear-Com Intercom Systems: 4065 Hollis Street, Emeryville, CA 94608, USA

Ph: (510) 496-6666, Fax: (510) 496-6699, www.clearcom.com
International Sales: PO Box 302, Walnut Creek, CA 94597, USA, Ph: (925) 932-8134, Fax: (925) 932-2171
©2000 Clear-Com Intercom Systems. PL-Pro is a Registered Trademark of Clear-Com. #PS22/600