Total No. of Questions: 8] SEAT No.

:
PA-1209 [5925]-231
[Total No. of Pages : 3

S.E. (Electrical Engineering)

ELECTRICAL MACHINES-I
(2019 Pattern) (Semester-IV) (203146)
Time : 2½ Hours] [Max. Marks : 70
Instructions to the candidates:
1) Answer Q1 or Q2, Q3 or Q4, Q5 or Q6, Q7 or Q8.
2) Neat diagrams must be drawn wherever necessary.
3) Figures to the right indicate full marks.
4) Assume suitable data, if necessary.
5) Use of non-programmable calculator is allowed.
Q1) a) Give any two points of comparison between LAP winding and WAVE
winding for DC machine. [4]
b) Draw the power stage diagram of DC motor. Clearly indicate various
losses along with respective formulae for the losses. [6]
c) A DC Shunt motor develops output power of 7355 watt and runs at 700
rpm. It is connected across 400 volt DC supply and draws a current of
23 Ampere. The mechanical and iron losses are 735.5 Watt. [8]
Determine-
i) Efficiency of Motor
ii) Armature resistance of motor

OR

Q2) a) The armature of 4 pole DC shunt motor has LAP winding which is
accommodated in 60 slots, each slot carries 20 conductors. [4]
If the useful flux per pole is 23 milli Weber, determine the total torque
developed by motor in Newton meter. The armature current is 50 Ampere.
[6]
b) What is meant by back emf in DC motor? State the equation of back
emf. Also explain how back emf acts as a regulating mechanism when
load on DC motor changes. [8]
c) Draw the connection diagram of shunt, series DC motors. State their
current & voltage distrubution equations.

P.T.O.
Q3) a) State any one application of- [3]
i) DC shunt
ii) Series &
iii) Cumulative compound motor
b) Sketch & explain the Torque- Armature current characteristics of [6]
i) DC shunt motor
ii) Series motor.
c) A 250 V DC Shunt motor takes a current of 6 Ampere and runs at 1200
rpm. The armature resistance is 0.05 Ohm and shunt filed resistance is
250 Ohm. Determine the speed of motor when it is loaded and taking a
current of 31 Ampere. [8]

OR

Q4) a) What is meant by reactance voltage in case of commutation in DC

machine? [3]
b) Draw the circuit diagram & explain the speed control of DC shunt motor
by armature voltage control also draw the nature of graph (Armature
voltage Vs. speed). [6]
c) Draw the connection diagram of 3 point starter used for DC shunt motor
& explain the function of [8]
i) Hold on coil &
ii) Over load coil

Q5) a) Draw the power flow diagram of 3-ph Induction motor. [4]
b) A 6 pole, 3 phase induction motor is connected to 400 volt, 50 Hz ac
supply. Calculate-
i) the speed of rotating magnetic field of the motor
ii) Speed of motor at 3% slip
iii) the rotor emf frequency at 3% slip [6]
c) Draw and explain torque-Slip characteristics of 3 phase induction motor
with respective mathematical expressions. Clearly mark the two regions
and point of maximum torque and starting torque [8]

OR

[5925]-231 2
Q6) a) Derive the condition for maximum starting torque of 3 phase induction
motors with usual notations. [4]
b) With suitable diagram explain constructional details of 3 phase slipring
induction motor [6]
c) The input to 3 phase, 6 pole, 50 Hz, induction motor is 47 kWatt at
certain load. The stator losses are 1.5 kWatt and mechanical losses are
1k Watt. Determine the HPoutput power of motor when it runs at 970
rpm. (Take 1 HP = 746 watt) [8]

Q7) a) State the types of starters used for induction motors. [3]
b) With suitable circuit diagram explain no load and blocked rotor test on 3
phase induction motor. Also write respective formulae involved in
calculation part for determining the respective parameters [6]
c) Draw the connection diagram of star-delta starter used for 3-ph induction
motor & explain its working [8]

OR
Q8) a) Obtain the approximate equivalent circuit diagrams fo 3-ph induction
motor step by step. Label it & state the meaning of each nomenclature
used. [7]
b) Using data from No load & Blocked rotor test on 3-ph induction motor;
Draw the circle diagram & write the procedure to find full load slip,
locate the points for slip = 0, 1 [10]



[5925]-231 3
Total No. of Questions : 8] SEAT No. :

PA-1210 [Total No. of Pages : 6

[5925]-232
S.E. (Electrical Engineering)
NETWORK ANALYSIS
(2019 Pattern) (Semester - IV) (203147)

Time : 2½ Hours] [Max. Marks : 70

Instructions to the candidates:
1) Answer Q.1 or Q.2, Q.3 or Q.4, Q.5 or Q.6, Q.7 or Q.8.
2) Neat diagrams must be drawn wherever necessary.
3) Figures to the right indicate full marks.
4) Use of calculator is allowed.
5) Assume suitable data if necessary.

Q1) a) What is time constant? State time constant in case of Series R-L circuit
and series R-C circuit. [6]

b) In the network shown in Fig. 1, switch is closed at t = 0 with capacitor

 2 
is uncharged. Find the value of i (0 ), di (0 ) , d i (02 ) . [6]
dt dt

c) In the circuits in Fig. 2. The switch is closed at t = 0. [6]

i) Obtain expression for current in the circuit for t > 0. Using the
classical method.

P.T.O.
 ii) Find value of current at t = 0.25 sec.

OR

Q2) a) A coil which has an inductance of 40mH and a resistance of 2  is

connected to form an LR series circuit. If they are connected to a 20V
DC supply. Find [6]

 R 
i) Value of the induced emf after 10ms v (t )  ve  t  .
 L 

ii) The final steady state value of the current.

iii) Time constant of the RL series circuit.

b) In the network shown in Fig. 3, switch is closed at t = 0. Find the value

 di (0 ) d 2i (0 )
of i (0 ), , Assume the initial current of inductor to be
dt dt 2
zero. [6]

[5925]-232 2
 c) In R-L-C circuit Fig. 4 is excited by D.C. voltage source. Find current
i (t) using conventional method. The switch is closed at time t = 0. [6]

Q3) a) Find the inverse Laplace transform of given network given F(s). [5]

(s + 2)
F(s ) =
s (s +3)

b) Find the Laplace transform of given network given f (t). [5]

f (t )  e3t .sin 2t  t . e2t

c) Obtain f(t) for the signal shown in Fig. 5. Also determine Laplace
transform of f(t). [7]

OR

[5925]-232 3
Q4) a) Determine resultant current i(t) if switch is closed at t = 0. In R-L-C
series circuit Fig. 6 by using Laplace transform. [9]

2
b) Solve the differential equation d x2(t )  3 dx (t )  2 x (t )  4et , where
dt dt
x (0–) = 1, x (01 )   1. [8]

Q5) a) Develop relation between ‘Z’ parameter and transmission parameter .

[5]

b) Explain the following in relation with filters. [6]

i) stop band.

ii) pass band.

iii) cut-off frequency.

c) Obtain y-parameters of two port network for the given network in the
fig.7. [7]

OR

[5925]-232 4
Q6) a) Define ABCD parameters and Hybrid parameters of two port networks.
[5]
b) Design constant K-low pass filter to have a cut-off frequency of 796 Hz
when terminated in a 600  resistance in both the T and π
configurations. [6]
c) Obtain Z-parameters of two-port network for the given network in the
Fig. 8. [7]

Q7) a) Define : [5]

i) Poles of system function.

ii) Zeros of system function.

b) The voltage V(s) in a network given by : [6]

2s
I( s ) 
( s 1)( s  3)

Plot poles and zeros in the plane and obtain time domain response of
current.

c) Find the driving point admittance Y11 (s) for the network shown in
Fig. 9 and plot pole-zone diagram. [6]

OR

[5925]-232 5
Q8) a) Define various network functions of a one-port network. [5]

b) Find the driving point impedance Z11 (s) for the network shown in
Fig. 10 [6]

c) The voltage V(s) in a network given by : [6]

5( s  5)
V ( s) 
( s  2)( s  7)

Plot poles and zeros in the plane and obtain time domain response of
voltage.



[5925]-232 6
Total No. of Questions : 8] SEAT No. :
PA-1211 [Total No. of Pages : 3
[5925]-233
S.E. (Electrical)
NUMERICAL METHODS AND COMPUTER PROGRAMMING
(2019 Pattern) (Semester - IV) (203148)

Time : 2½ Hours] [Max. Marks : 70

Instructions to the candidates:
1) Answer Q1 or Q2, Q3 or Q4, Q5 or Q6, Q7 or Q8.
2) Neat diagrams must be drawn wherever necessary.
3) Assume suitable data, jf necessary.
4) Use of logarithmic tables slide rule, Mollier charts, electronic pocket calculator
and steam tables is permitted.
5) Assume suitable data, if necessary.

Q1) a) Prove [6]

i) Δ − ∇ = Δ∇

ii) (1 + Δ )(1 − ∇ ) = 1
b) Following table gives the distance in nautical miles of the visible horizon
for the given heights in feet above earth. [6]
X height 200 250 300 350 400
Y distance 15.04 16.81 18.42 19.90 21.27
Find the distance when height is 218 feet.
c) Derive the formula for Newton’s forward interpolation formula for the
equally spaced data points. [5]
OR
Q2) a) Find f(10) of the cubic function passing through the points (4,–43) (7,83)
(9,327) and (12,1053) using Newtons divided difference formula. [6]
b) Derive Lagrange’s Interpolation formula for unequally spaced data points.[6]
c) Apply Bessel’s central difference formula to obtain f(32) given that [5]
f(25)=0.2707 f(30)=0.3027 f(35)=0.3386 f(40)=0.3794

[5925]-233 1 P.T.O.
Q3) a) Derive Trapezoidal rule for numerical integration as a special case of
Newton’s Cote formula. [6]
b) A river is 80m wide. The depth d in meters at a distance x meters from
one bank is given in the following table [6]
X(m) 0 10 20 30 40 50 60 70 80
D(m) 0 4 7 8 12 15 14 8 3
Find approximately the area of cross section by
i) Trapezoidal rule
ii) Simpson’s 1/3rd rule.
c) Derive formula for numerical differentiation of first order using Newton’s
forward interpolation technique. [5]
OR

  ( x + y ) dxdy using Simpsons 1/3

1 1
rd
Q4) a) Evaluate rule with h=k=1/2 [6]
0 0

b) Evaluate the first and second derivative of √x at x=15 from the following
data [6]
x 15 17 19 21 23
√x 3.873 4.123 4.354 4.583 4.796
c) Derive Simpson’s 1/3rd rule for numerical integration as a special case of
Newton’s Cote formula. [5]

Q5) a) Solve the system of equations by Gauss Jordan method [6]

x+y+z=9
2x – 3y + 4z = 13
3x + 4y + 5z = 40
b) Use Gauss Seidel method to solve the following system of equations[6]
6x1++x2+x3=105
4x1+8x2+3x3=155
5xl+4x2–10x3=65
c) Explain Gauss Jacobi method for the solution of linear simultaneous
equations. [6]
OR
[5925]-233 2
Q6) a) Explain Gauss-Seidal method for solution of linear simultaneous equation.
(Numerical is not expected) [6]
b) Apply Gauss Jordan method to find inverse of [6]

3 0 2 
A =  2 0 −2 
 
 0 1 1 

c) Using Jacobi iterative method solve the following system of linear

simultaneous equations. Take x (0) = y (0) = z (0) = 0 perform 5 iterations.[6]
3x + y + z = 2
x + 4y + 2z = –5
x + 2y + 5z = 2

Q7) a) Use 4th order RK method to estimate approximate value of y for x = 0.1
with step size is 0.1, if dy/dx = x + y2 given that y = 1 when x = 0. [6]

dy
b) Apply Euler’s method to find y(0.1). Given = xy , y(1) =5. Show 5
dx
iterations. [6]
c) Explain Euler’s method for the solution of ordinary differential equation.[6]
OR
Q8) a) Explain Taylor’s series method for solution of ordinary differential
equations. [6]
b) Use Runge Kutta second order method of find an approximate value of
y correct to three places of decimal when x = 0.1, given that y = 1.2
dy
when x = 1 and = 3x + y2. [6]
dx

dy
c) Find the value of x = 0.1 for the equation = 1 + xy and y(0)=1. Take
dx
step size h = 0.1 by Taylor series method. [6]

  
[5925]-233 3
Total No. of Questions: 8] SEAT No. :
PA-1212 [5925]-234
[Total No. of Pages : 2

S.E. (Electrical)
FUNDAMENTAL OF MICROCONTROLLER & APPLICATIONS
(2019 Pattern) (Semester-IV) (203149)
Time : 2½ Hours] [Max. Marks : 70
Instructions to the candidates:
1) Solve Q.1 or Q.2, Q.3 or Q.4, or Q.5 or Q.6, Q.7 or Q.8.
2) Figures to the right indicate full marks.
3) Neat diagrams must be drawn wherever necessary.
4) Assume suitable data, if necessary.

Q1) a) Draw & describe TMOD register. [6]

b) Write short note on Data Types in C. [6]
c) Write a program to generate square wave of 50Hz frequency with 50%
duty cycle on pin 2.3. Assume XTAL=11.0592 MHz & use timer 0 in
mode l. [6]

OR
Q2) a) Describe the Timer modes in 8051 microcontrollers. [6]
b) Draw & explain TCON register. [6]
c) Write C Program to toggle bit P1.5 of port P1, 5000 times. [6]

Q3) a) Explain interrupt structure of 8051 microcontroller with neat diagram.

[6]
b) With the help of diagram explain interfacing of ADC 0809 with 8051
microcontrollers. [6]
c) Explain Interrupt Priority Register of 8051 Microcontroller. [5]

OR
Q4) a) Write short note on Interrupt enable register. [6]
b) Write a program to turn off LED for connected to Port 0 when interrupt
0 occurs and turn it on when interrupt 1 occurs. [6]
c) Explain the SOC, EOC, & OE pin of ADC 0809. [5]

P.T.O.
Q5) a) Write Short note on SCON register. [6]
b) Explain Steps to transfer Data Serially in 8051 microcontroller. [6]
c) Write program to transfer letter ‘T’serially 10 times at baud rate of 4800.
Use serial port in mode 1. XTAL=12MHz. [6]

OR

Q6) a) Write short note AT commands required for GSM. [6]

b) Explain Steps to receive Data Serially in 8051 microcontroller. [6]
c) Explain Serial port structure of 8051 microcontroller. [6]

Q7) a) Explain LED interfacing with 8051 microcontroller. [6]

b) With the help of block diagram explain Key interfacing using 8051. [6]
c) With the help of block diagram explain Power measurement using 8051.
[5]

OR
Q8) a) With the help of block diagram explain Voltage & current measurement
using 8051. [6]
b) Draw interfacing diagram of a stepper motor with 8051 and write program
to rotate stepper motor 360 Degree in anticlockwise direction with step
angle of 1.8 degree. [6]
c) Explain relay interfacing with 8051 microcontroller. [5]



[5925]-234 2