This document is a guide for installing Arch Linux using the live system booted from an installation medium

made from an official installation image. The installation medium provides accessibility features which are
described on the page Install Arch Linux with accessibility options. For alternative means of installation,
see Category: Installation process.

Before installing, it would be advised to view the FAQ. For conventions used in this document, see Help:
Reading. In particular, code examples may contain placeholders (formatted in italics) that must be replaced
manually.

This guide is kept concise and you are advised to follow the instructions in the presented order per section. For
more detailed instructions, see the respective Arch Wiki articles or the various programs' man pages, both
linked from this guide. For interactive help, the IRC channel and the forums are also available.

Arch Linux should run on any x86_64-compatible machine with a minimum of 512 MiB RAM, though more
memory is needed to boot the live system for installation.[1] A basic installation should take less than 2 GiB of
disk space. As the installation process needs to retrieve packages from a remote repository, this guide assumes
a working internet connection is available.

Pre-installation
Acquire an installation image
Visit the Download page and, depending on how you want to boot, acquire the ISO file or a netboot image, and
the respective PGP signature.

Verify signature
It is recommended to verify the image signature before use, especially when downloading from an HTTP mirror,
where downloads are generally prone to be intercepted to serve malicious images.

On a system with GnuPG installed, do this by downloading the ISO PGP signature (under Checksums in the
page Download) to the ISO directory, and verifying it with:

$ gpg --keyserver-options auto-key-retrieve --verify archlinux-version-

x86_64.iso.sig

Alternatively, from an existing Arch Linux installation run:

$ pacman-key -v archlinux-version-x86_64.iso.sig

Note:

 The signature itself could be manipulated if it is downloaded from a mirror site, instead of
from archlinux.org as above. In this case, ensure that the public key, which is used to decode the
signature, is signed by another, trustworthy key. The gpg command will output the fingerprint of the public
key.
 Another method to verify the authenticity of the signature is to ensure that the public key's fingerprint is
identical to the key fingerprint of the Arch Linux developer who signed the ISO-file. See Wikipedia:Public-
key cryptography for more information on the public-key process to authenticate keys.
Prepare an installation medium
The ISO can be supplied to the target machine via a USB flash drive, an optical disc or a network with PXE:
follow the appropriate article to prepare yourself an installation medium from the ISO file.

For the netboot image, follow Netboot#Boot from a USB flash drive to prepare a USB flash drive for UEFI
booting.

Boot the live environment

Note: Arch Linux installation images do not support Secure Boot. You will need to disable Secure Boot to boot
the installation medium. If desired, Secure Boot can be set up after completing the installation.

1. Point the current boot device to the one which has the Arch Linux installation medium. Typically it is
achieved by pressing a key during the POST phase, as indicated on the splash screen. Refer to your
motherboard's manual for details.
2. When the installation medium's boot loader menu appears,
 if you used the ISO, select Arch Linux install medium and press Enter to enter the installation
environment.
 if you used the Netboot image, choose a geographically close mirror from Mirror menu, then
select Boot Arch Linux and press Enter.

Tip:

 The ISO uses systemd-boot for UEFI and syslinux for BIOS booting. Use
respectively e or Tab to enter the boot parameters. The Netboot image uses iPXE and the
boot parameters can be specified in the Boot options menu. See README.bootparams for a
list.
 A common example of manually defined boot parameter would be the font size. For better
readability on HiDPI screens—when they are not already recognized as such—
using fbcon=font:TER16x32 can help. See HiDPI#Linux console (tty) for a detailed
explanation.
3. You will be logged in on the first virtual console as the root user, and presented with a Zsh shell
prompt.
To switch to a different console—for example, to view this guide with Lynx alongside the installation—use
the Alt+arrow shortcut. To edit configuration files, mcedit(1), nano and vim are available.
See pkglist.x86_64.txt for a list of the packages included in the installation medium.

Set the console keyboard layout and font

The default console keymap is US. Available layouts can be listed with:

# localectl list-keymaps

To set the keyboard layout, pass its name to loadkeys(1). For example, to set a German keyboard layout:

# loadkeys de-latin1

Console fonts are located in /usr/share/kbd/consolefonts/ and can likewise be set

with setfont(8) omitting the path and file extension. For example, to use one of the largest fonts suitable
for HiDPI screens, run:

# setfont ter-132b

Verify the boot mode

To verify the boot mode, check the UEFI bitness:

# cat /sys/firmware/efi/fw_platform_size

 If the command returns 64, the system is booted in UEFI mode and has a 64-bit x64 UEFI.
 If the command returns 32, the system is booted in UEFI mode and has a 32-bit IA32 UEFI. While this is
supported, it will limit the boot loader choice to those that support mixed mode booting.
 If it returns No such file or directory, the system may be booted in BIOS (or CSM) mode.
If the system did not boot in the mode you desired (UEFI vs BIOS), refer to your motherboard's manual.

Connect to the internet

To set up a network connection in the live environment, go through the following steps:

1. Ensure your network interface is listed and enabled, for example with ip-link(8):

# ip link

2. For wireless and WWAN, make sure the card is not blocked with rfkill.
3. Connect to the network:
 Ethernet—plug in the cable.
 Wi-Fi—authenticate to the wireless network using iwctl.
 Mobile broadband modem—connect to the mobile network with the mmcli utility.
4. Configure your network connection:
 DHCP: dynamic IP address and DNS server assignment (provided by systemd-
networkd and systemd-resolved) should work out of the box for Ethernet, WLAN, and WWAN
network interfaces.
 Static IP address: follow Network configuration#Static IP address.
5. The connection may be verified with ping:

# ping archlinux.org

Note: In the installation image, systemd-networkd, systemd-resolved, iwd and ModemManager are
preconfigured and enabled by default. That will not be the case for the installed system.
Update the system clock
In the live environment systemd-timesyncd is enabled by default and time will be synced automatically once a
connection to the internet is established.

Use timedatectl(1) to ensure the system clock is synchronized:

# timedatectl

Partition the disks

When recognized by the live system, disks are assigned to a block device such
as /dev/sda, /dev/nvme0n1 or /dev/mmcblk0. To identify these devices, use lsblk or fdisk.

# fdisk -l

Results ending in rom, loop or airootfs may be ignored. mmcblk* devices ending
in rpbm, boot0 and boot1 can be ignored.

Note: If the disk does not show up, make sure the disk controller is not in RAID mode.
Tip: Check that your NVMe drives and Advanced Format hard disk drives are using the optimal logical sector
size before partitioning.
The following partitions are required for a chosen device:

 One partition for the root directory /.

 For booting in UEFI mode: an EFI system partition.
Use a partitioning tool like fdisk to modify partition tables. For example:
# fdisk /dev/the_disk_to_be_partitioned

Note:

 Take time to plan a long-term partitioning scheme to avoid risky and complicated conversion or re-
partitioning procedures in the future.
 If you want to create any stacked block devices for LVM, system encryption or RAID, do it now.
 If the disk from which you want to boot already has an EFI system partition, do not create another one,
but use the existing partition instead.
 Swap space can be set on a swap file for file systems supporting it. Alternatively, disk based swap can be
avoided entirely by setting up swap on zram after installing the system.
Example layouts

UEFI with GPT

Mount point on the

Partition Partition type Suggested size
installed system

/boot1 /dev/efi_system_partition EFI system 1 GiB

partition

[SWAP] /dev/swap_partition Linux swap At least 4 GiB

/ /dev/root_partition Linux x86-64 Remainder of the device. At

root (/) least 23–32 GiB.

1. Other mount points, such as /efi, are possible, provided that the used boot loader is capable of
loading the kernel and initramfs images from the root volume. See the warning in Arch boot
process#Boot loader.

BIOS with MBR

Mount point on the installed Partition

Partition Suggested size
system type

[SWAP] /dev/swap_partition Linux swap At least 4 GiB

/ /dev/root_partition Linux Remainder of the device. At least

23–32 GiB.

See also Partitioning#Example layouts.

Format the partitions

Once the partitions have been created, each newly created partition must be formatted with an appropriate file
system. See File systems#Create a file system for details.

For example, to create an Ext4 file system on /dev/root_partition, run:

# mkfs.ext4 /dev/root_partition

If you created a partition for swap, initialize it with mkswap(8):

# mkswap /dev/swap_partition

Note: For stacked block devices replace /dev/*_partition with the appropriate block device path.
If you created an EFI system partition, format it to FAT32 using mkfs.fat(8).

Warning: Only format the EFI system partition if you created it during the partitioning step. If there already was
an EFI system partition on disk beforehand, reformatting it can destroy the boot loaders of other installed
operating systems.

# mkfs.fat -F 32 /dev/efi_system_partition

Mount the file systems

Mount the root volume to /mnt. For example, if the root volume is /dev/root_partition:

# mount /dev/root_partition /mnt

Create any remaining mount points under /mnt (such as /mnt/boot for /boot) and mount the volumes in their
corresponding hierarchical order.

Tip: Run mount(8) with the --mkdir option to create the specified mount point. Alternatively, create it
using mkdir(1) beforehand.
For UEFI systems, mount the EFI system partition:

# mount --mkdir /dev/efi_system_partition /mnt/boot

If you created a swap volume, enable it with swapon(8):

# swapon /dev/swap_partition

genfstab(8) will later detect mounted file systems and swap space.

Installation
Select the mirrors
Packages to be installed must be downloaded from mirror servers, which are defined
in /etc/pacman.d/mirrorlist. On the live system, after connecting to the internet, reflector updates the
mirror list by choosing 20 most recently synchronized HTTPS mirrors and sorting them by download rate.

The higher a mirror is placed in the list, the more priority it is given when downloading a package. You may want
to inspect the file to see if it is satisfactory. If it is not, edit the file accordingly, and move the geographically
closest mirrors to the top of the list, although other criteria should be taken into account.

This file will later be copied to the new system by pacstrap, so it is worth getting right.

Install essential packages

Note: No software or configuration (except for /etc/pacman.d/mirrorlist) gets carried over from the live
environment to the installed system.
Use the pacstrap(8) script to install the base package, Linux kernel and firmware for common hardware:

# pacstrap -K /mnt base linux linux-firmware

Tip:

 You can substitute linux with a kernel package of your choice, or you could omit it entirely when installing
in a container.
 You could omit the installation of the firmware package when installing in a virtual machine or container.
The base package does not include all tools from the live installation, so installing more packages may be
necessary for a fully functional base system. To install other packages or package groups, append the names to
the pacstrap command above (space separated) or use pacman to install them while chrooted into the new
system. In particular, consider installing:

 CPU microcode updates—amd-ucode or intel-ucode—for hardware bug and security fixes,

 userspace utilities for file systems that will be used on the system—for the purposes of e.g. file system
creation and fsck,
 utilities for accessing and managing RAID or LVM if they will be used on the system,
 specific firmware for other devices not included in linux-firmware (e.g. sof-firmware for onboard
audio, linux-firmware-marvell for Marvell wireless and any of the multiple firmware packages
for Broadcom wireless),
 software necessary for networking (e.g. a network manager or a standalone DHCP
client, authentication software for Wi-Fi, ModemManager for mobile broadband connections),
 a console text editor (e.g nano) to allow editing configuration files from the console,
 packages for accessing documentation in man and info pages: man-db, man-pages and texinfo.
For comparison, packages available in the live system can be found in pkglist.x86_64.txt.

Configure the system

Fstab
Generate an fstab file (use -U or -L to define by UUID or labels, respectively):

# genfstab -U /mnt >> /mnt/etc/fstab

Check the resulting /mnt/etc/fstab file, and edit it in case of errors.

Chroot
Change root into the new system:

# arch-chroot /mnt

Time
Set the time zone:

# ln -sf /usr/share/zoneinfo/Region/City /etc/localtime

Run hwclock(8) to generate /etc/adjtime:

# hwclock --systohc

This command assumes the hardware clock is set to UTC. See System time#Time standard for details.

To prevent clock drift and ensure accurate time, set up time synchronization using a Network Time
Protocol (NTP) client such as systemd-timesyncd.

Localization
Edit /etc/locale.gen and uncomment en_US.UTF-8 UTF-8 and other needed UTF-8 locales. Generate the
locales by running:

# locale-gen

Create the locale.conf(5) file, and set the LANG variable accordingly:

/etc/locale.conf

LANG=en_US.UTF-8

If you set the console keyboard layout, make the changes persistent in vconsole.conf(5):

/etc/vconsole.conf

KEYMAP=de-latin1

Network configuration
Create the hostname file:

/etc/hostname

yourhostname

Complete the network configuration for the newly installed environment. That may include installing
suitable network management software, configuring it if necessary and enabling its systemd unit so that it
starts at boot.

Initramfs
Creating a new initramfs is usually not required, because mkinitcpio was run on installation of
the kernel package with pacstrap.

For LVM, system encryption or RAID, modify mkinitcpio.conf(5) and recreate the initramfs image:

# mkinitcpio -P

Root password
Set the root password:

# passwd
Boot loader
Choose and install a Linux-capable boot loader.

Reboot
Exit the chroot environment by typing exit or pressing Ctrl+d.

Optionally manually unmount all the partitions with umount -R /mnt: this allows noticing any "busy" partitions,
and finding the cause with fuser(1).

Finally, restart the machine by typing reboot: any partitions still mounted will be automatically unmounted
by systemd. Remember to remove the installation medium and then login into the new system with the root
account.