Quick Reference Guide for

CashCode

+1 905-303-8874 www.one.cashcode.com
1-800-584-2633 [email protected]

© 2013 Crane Payment Solutions Part No. OPT-FLS-FB, Rev 2.

 CashCode

Getting Started:
My Bill Validator is not Perform Self-Diagnostic
working Troubleshooting (see page
13) or perform a Diagnostic
through a PC (see page 15) to
check for hardware issues
My Bill Validator frequently Perform Preventative
jams/has a low acceptance Maintenance (see page 9) to
rate keep the Bill Validator running
at top performance
My Bill Validator rejects some, Check the DIP Switch Settings
or all bills (see page 12) on the side of
the validating head
My Bill Validator requires Write down the Part Number
service and Serial Number of the Bill
Validator (See page 3) and
find the contact information
for your nearest service center
(see back cover)
My Bill Validator requires new Order a software update from
software Crane Payment Solutions and
follow your jurisdictional
Software Update (see page
16) procedure
I need more detailed Detailed documentation for
information on my Bill your bill validator and all
Validator its components is available
online at:
http://support.cashcode.com
http://elearning.cashcode.com

-2-
CashCode

Product Components and Labels

Validating Head (Module)

Part No: FLSV-XXXX
Serial No: XXXXXXXXXXXX

Diagnostic/Status LED

Software Version
Label: FLS-XXXX-XXXXXX
(See page 16 for
description)

Front Service USB Port

(See page 15 for
description)

Boot Version Label

For additional information please register at:

http://elearning.cashcode.com

-3-
 CashCode

Product Components and Labels

TM

CashCode

Bill Validator
(Assembly w/o Cashbox)
Label: FLS-XXXX

Cashbox Part Numbers

Part Bill Handle Housing
Number Capacity Style FLSH-XXXX

FLSC-0002* 600

FLSC-0202* 900 Flexible FLSH-0003

FLSC-0102* 1,000

FLSC-0001* 600
FLSH-0003
FLSC-0101* 1,000 Foldable

Cashbox (Module) FLSC-2500 2,500 FLSH-0004

Label: FLSC-XXXX* *FLSCTXXXX boxes are oneTrack enabled TM

Cashbox Locks:
Standard Locking Hasps P/N - #5110086
Lock Size: Drum - 3/4 “ Length - 5/8” or 11/8”

All Product Labels contain a generic part

number and unique serial number.

-4-
Bezel Part Numbers

FLSB -5101: GPT Compatible Bezel with

Blue/Red runway lights

FLSB-530XY: Cole style bezel with runway lights

X: 1 - Full rectangle X: 3 - Flange cut top
X: 5 - Raised bottom X: 7 - Flange cut top
surface and raised surface
Y: _ - Green/Red Lights Y: R - Red/Green Lights
Y: B - Blue/Red Lights

FLSB-570X: Konami compatible Bezel with

open top and runway lights (Blue/Red)
X-Varian:
X: 1 – Standard
X: 2 – AGT/Stargames Customization

FLSB-5901: BAT (Aristocrat Compatible) Bezel

with oval shaped indicator light (Blue/Red)

-5-
 Bezel Part Numbers

FLSB-5501: CashCode Coin Proof Plastic Bezel

with optic channel for status light (Green/Red)

Suitable for outdoor applications.

FLSB-7103: CashCode Coin proof Matal Bezel

with optic channel for status light (Green/Red)
This bezel requires additional grounding
hardware on the unit housing. Please see
the Bezel User Guide for mounting
instructions.

FLSB-7603: CashCode Coinproof Metal Bezel

with status light (Green/Red). This bezel is
mounted on an upside-stacker installation.
This bezel requires additional grounding
hardware on the unit housing.

FLSB-5902: Verve Bezel (Aristocrat compatible)

Bezel with oval shaped indicator light (Blue/
Red)

FLSB-5401: WMS BBXD Slant Top Bezel

For information on custom bezel configurations,

contact CashCode Technical Support
http://support.cashcode.com

-6-
 CashCode one Interface Connector Pin-out:
TM

Terminal P/N (JAE): DR-SC24-1-7000 | Mating Socket P/N - #0100455

Above items can be ordered separately, or in one kit: OPT-MKFLS-24
TERMINAL FUNCTION
1 GROUND BUS
2 RECEIVE DATA (RxD-EXT)
3 TRANSMIT DATA (TxD-EXT)
4 POWER (VCC)
5 GROUND (GND)
6 RECEIVE DATA (RXD-EXT1)
7 INTERFACE GROUND (GND-EXT/EXT1)
8 TRANSMIT DATA (TXD-EXT1)
9 RS485-A BUS
10 RS485-B BUS
11 INPUT SIGNAL/ RECEIVE DATA (INP-RXD, MDB)
12 INPUT SIGNAL (INP-TTL1, MDB)
13 POWER (0V)
14 INPUT SIGNAL (INP-TTL2)
15 OUTPUT SIGNAL (OPEN-COLLECTOR )/ TRANSMIT DATA
16 OUTPUT SIGNAL (OPEN-COLLECTOR )
17 LED CATHODE/ OUTPUT SIGNAL (OPEN-COLLECTOR )
18 LED ANODE (A-LED-BDP)
19 POWER (12V/24V)
20 TRANSMIT DATA (TXD-BDP)
21 RECEIVE DATA (RXD-BDP)
22 MASTER RESET (RST-BDP)

23 INTERFACE GND (GND-BDP)

24 INTERFACE POWER (+12V BDP)

It is highly recommended to ensure communication pin (1)

and unit ground pin (5) are not interconnected.

-7-
 CashCode

Installing Security Switch Kit

The optional cassette-present security switch allows the

host machine to detect whether a cashbox is present in the
validator housing. To install the kit:

1. Attach the provided

cable to the switch as
shown
2. Use a #2x1/2” wood
screw to secure the
switch to the FLS
Housing
3. Feed the cable up
through the housing
and connect to your
host machine
4. A security switch can
be installed on either
or both sides of the
housing

Connecting to host Machine:

Brown wire - NC switch
Red wire - NO switch
Orange wire - Common Ground
To order the Security Switch Kit
See part number: OPT-MKFLS-SWH

For information on ordering a factory-installed

switch kit, contact CashCode Technical Support
http://support.cashcode.com

-8-
 CashCode

Preventative Maintenance

To keep your oneTM Bill Validator running at top

performance, the bill path should be cleaned as required*.

DO NOT use Acetone, Petroleum, or Mineral

Oil based solvents as they will cause damage
to Bill Validator parts and void your warranty

Open the validating head using the grey latch, and follow
cleaning directions below. Refer to the colour legend for
rollers and sensors.

Special Cleaning Card (P/N: 8402022) and Cleaning Kits

are available (P/N: OPT-CLEAN-KIT-1 & OPT-CLEAN-KIT-2)

-9-
AFFECTED AREA CLEANING PROCEDURE
1. Blow with compressed air to remove all
Dirt and dust particles in bill loose particles
path (entire surface) 2. Wipe with a micro-fiber anti-static
cloth to remove all other residues
1. Blow with compressed air to remove all
Dirty Optical and Ultraviolet loose particles
Sensors 2. Check lens condition and clean using
a micro-fiber cloth and LCD cleaner
Check for cracked o-rings and clean
Dirty Rollers and O-Rings
using a micro-fiber cloth and LCD cleaner

*For more details on cleaning and maintenance,

check http://elearning.cashcode.com

- 10 -
 CashCode

DIP Switch Settings

The DIP switches are located on the side of the validating

head near the bottom:

ON State

4
3 2 1
OFF State

The first four switches configure the operation of the validator.

Only the fourth switch should be used during service and
troubleshooting procedures to select between:

Host Mode: This is the mode for normal operation.

Service Mode: This is a stand alone mode for testing the oneTM
Bill Validator (see page 13 for procedure).

PARAMETER SWITCH ON OFF

Orientation of the Bar Code Bar Code
SW2.1
ticket Four-Way Face-Up
Stacker orientation SW2.2 Down Up
Connectivity* SW2.3 oneCheck TM
oneTrackTM
Mode SW2.4 Service Mode Host Mode

* Default communication speed is 9600 Baud unless specified otherwise

- 11 -
A series of eight DIP switches configures accepted
denominations as well as acceptance mode.

ON State

8 7 6 5 4 3 2 1
OFF State

PARAMETER SWITCH ON OFF

Denomination #1 SW1.1 Enabled Disabled
Denomination #2 SW1.2 Enabled Disabled
Denomination #3 SW1.3 Enabled Disabled
Denomination #4 SW1.4 Enabled Disabled
Denomination #5 SW1.5 Enabled Disabled
Denomination #6 SW1.6 Enabled Disabled
Denomination #7 SW1.7 Enabled Disabled
Acceptance Mode SW1.8 Accept All Reject Unfit Bills

For a complete documentation of switch descriptions, please

see the software release specifications for your particular
country/protocol at: http://support.cashcode.com

- 12 -
 CashCode

Self-Diagnostic Troubleshooting

CashCode’s oneTM Bill Validator is equipped with an automatic

self-diagnostic test to aid in repair and maintenance.
Step 1: Put the validator into service mode (see page 11 and turn the
power on to start the test.
Step 2: After the test, check the status light:
GREEN: Test passed
RED: Count the number of flashes, turn power off, and see
below table for solution.

RED FLASHES ERROR SOLUTION*

Cashbox is removed Check if cashbox is

1
from Bill Validator installed correctly
Failure of CPU comm.
2 Reset device power
magnetic board
Cashbox is full/ Remove cashbox, and
3
ready for drop insert empty replacement
1. Remove cashbox from
Bill Validator Housing
Mechanical jam in and extract crumpled or
4 cashbox or stacker jammed bill
failure 2. Turn power on and
check if stacker motor is
rotating
Failure of dielectric
5 Reset device power
sensor
Open validating head,
Failure of optical sensor
6 clean optical sensors
(see page 9)
Failure of magnetic Open validating head,
7 sensor clean inductive sensors
(see page 9)

- 13 -
RED FLASHES ERROR SOLUTION*

1. Open validating head,

clean path, close validator
Failure of transport 2. Release head from
8
motor chassis, check receiving
path, re-insert validator
head
Transport motor
9 Check power supply voltage
too fast
Failure of alignment Open validating head, clean
10
mechanism path, close Validator
Bill pathway is not
11 See Solution 8
empty
Bill jam in entry slot Open validating head and
12
(no credit is issued) remove bill from path
Open validating head
Overload of transport
13 and check to see if path
motor
is clean

14 System error Reset device power

Additional error codes for oneTrackTM operation:

Cashbox is Hot/ Return cashbox to soft
FLICKER x1 Machine number count room, replace with a
mismatch Cold box
1. Check for proper contact
of the antenna module
Antenna module or cable to the validating
FLICKER x2
cashbox failure head terminals
2. Replace antenna board
module

* Error codes will also trigger during regular operation mode

for on-the-spot diagnostic. If any problems persist, contact
your nearest Service Center or CashCode Technical Support
at: http://support.cashcode.com

- 14 -
 CashCode

Performance Audit and Diagnostics

You can collect statistics, perform diagnostics and install

software updates using the front service USB port.

USB cable
type A/B

PC with VCOM driver. Win 7 requires

CashCode oneTM Bill Validator
an update of the VCOM driver.

1. Connect a USB cable to your PC and the front service

port of your validator
2. If required, use the ‘Add New Hardware’ dialog to select
the CashCode VCOM driver, located in the /vcom/ folder
of your installation directory
3. Making sure the USB connection is successful and
launch the CC Navigator utility
4. Click the “Connect to device...” button

You can now use the utility to:

Read Performance Audit data from device.
Save the Performance Audit data to a file.
View saved Performance Audit data.
Perform a diagnostic test. Check the Guide tab for a
list of problems and solutions, and check the View
tabs for the specific location of a problem.
Print a repair ticket with relevant information from
the diagnostic.
Update the device’s firmware (some restrictions
apply, see pages 17 and 18).
When finished, use the Disconnect button.

Please refer to manual for additional information.

- 15 -
 CashCode

Software Updates

The oneTM Bill Validator is shipped with pre-installed

software, according to ordered specifications. It is
recommended to keep your unit’s firmware up-to-date*.

Software
FLS-XXXX-XXXXXX-XX
(1)-(2)(3)-(4)(5)(6)-(7)
(1) ONE Bill Validator Memory card
(2) Country code (ISO 3166-1)
(3) Protocol/OEM customization

}
(4) Control firmware
(5) Validation firmware Software Version
(6) C/Code Software Configuration
(7) Optional extensions indicating type of memory card.
Possible memory card extensions:

(___) Stay in/Single Download Card

Card is One Time Programmable

(-OP) The card is locked as read-only, and any

validators programmed with the card
will only accept OTP cards for future updates

(-99) Allows up to 99 downloads

Type 34: P1848-FSM34

- One Time Programmable (OTP)
- Stay-in/Single Download
- Kobetron Certifiable

Type 42: P1848-FSM42

- Multi Download

* For alternative update options please inquire with

CashCode Technical Support: http://support.cashcode.com

- 16 -
 CashCode

Software Updates

Memory Card Update Procedure:

1. Lift up the latch under the Validating Head, and remove
the Validating Head from the Housing.
2. Remove the old Memory Card from the slot if applicable.
3. Insert the new CashCode Memory Card into the Memory
Card slot of the Validating head (for correct insertion,
please see diagram below).
4. Insert the Validating Head into the Housing.
5. Turn Power ON and wait until the download process is
completed. During the download, a red-green status
light will blink.
6. Once the download is completed, the diagnostic light
will turn steady green. If the green light is flashing, refer
to the diagnostic table below.
7. A Multi Download Memory Card can be removed to
program more than one unit. However, a Stay-In/Single
Download Memory Card must be left inside the unit for
continued operation.

Please check your jurisdictional requirements to

see which update option is correct for your casino.

Notch facing towards the

front of the Bill Validator

“THIS SIDE UP”

- 17 -
 Front Service USB Update Procedure:
The Bill Validator must be Front Service USB-enabled (see
page 17) to perform the update operation.
Please note that CFS files are required for all OEM,
and BIN files are required for IGT and Ontario jurisdiction
1. See page 15 on instruction for connecting your validator to a
PC through USB
2. Launch the “Download Firmware” utility from the
CCNavigator
3. Load the appropriate software update and press Start
4. Remove the USB connection

VH control software versions prior to 44 require to go through a one

time activation process in order to enable USB software download.

Please check your jurisdictional requirements to

see which update option is correct for your casino.

Software Update Troubleshooting:

GREEN
ERROR SOLUTION*
FLASHES

Unable to write program

1 Repeat Procedure
memory

2 Firmware integrity error Unable to write program memory

1. Verify that the software is

suitable to the Bill Validator type
3 Wrong memory card 2. Insert correct type of CashCode
Memory Card
3. Repeat Procedure
1. Verify that software is suitable for
4 Security error download
2. Repeat procedure

* If you are unable to complete your software update procedure,

please contact CashCode Technical Support
http://support.cashcode.com

- 18 -
CashCode

Plastic Cover Disassembly

Side Cover Removal:

1. Open the upper guide and place Validating Head on
its side.
2. Insert flathead screwdriver about ¼” (0.5 mm) into the
notch between the blue side cover and the black
casing. Tilt the screwdriver approximately 45o by
applying downward pressure.

3. Apply pressure tangent

to the cover on the flat
edge, while slowly
lifting up on the
curved edge.
Right Panel P/N: FL85.02.005 (shown)
Left Panel P/N: FL85.02.005-01

4. Repeat step 3 on the

front of the unit.

- 19 -
Top Cover Removal:
1. Close the upper guide and place the unit on its
bottom
2. Insert flat head screwdriver about 1/4” (0.5mm) into
gap between the blue top plastic cover and the black
casing, and apply downward pressure until the cover
audibly pops.
3. Remove the screwdriver.
Carefully unlatch and
open the upper guide
approximately 45O
without resetting the
plastic casing.
4. Insert the screwdriver
into one of the two
notches between the
blue top cover and the
black casing, and tilt the
screwdriver to pop off Top Cover P/N: FL85.02.001
the casing. Repeat with
notch on the
other side.
5. Repeat step 4.

6. Repeat step 4.

Caution: CashCode recommends only certified service

technicians perform disassembly of your CashCode
oneTM Bill Validator.

* For complete disassembly instructions, check your

oneTM product service manual or visit,
http://elearning.cashcode.com

- 20 -
 and

Setting Machine/Location Number:

1. Connect your Bill Validator to a PC computer using a
USB cable, as described on page 15
2. Launch the SMNUtility.exe utility
3. Press “Connect” to establish communication with the
validating head 1
4. Enter a Machine and/or Location Number as well as the
Cashbox Size (default is 600), and transfer it to the
validating head. Check the output on the utility user
interface to verify correctness 2
5. Once ``Disconnect`` has been pressed, the computer
time and date will be set on the unit.

Selecting oneCheck™ Printer Settings:

The printer settings have two modes, Auto and Manual which
have the following function:
Method 1: Auto (default) 3
The dedicated printer will print the CAPR ticket
automatically once the CashBox has been removed.
Method 2: Manual
Once the CashBox has been
removed, the CAPR ticket will 2
only be printed once the latch
on the bottom of the FLS unit 3
has been depressed for over 4
4 seconds.
Next, select the printer brand
that will be used 4 1
(Default: Future Logic)

Once you click “Connect”, unit time and date will be

set to currect computer time.

- 21 -
Asset Reports from Database:
The oneTrackTM/oneCheckTM web based systems provide
employees with the following highly secured and easily
manageable financial and performance reports:

Report Type Details

Revenue Report Financial data, voucher and bill information
Filled-to-capacity box reports, showing high
Cashbox Full
traffic areas and emergency drops
Shows drops with zero activity, highlighting
Zero Revenue
potential issues with drops and collection
Scheduled/Arrived Shows status of Bill Validator
Missing Machine/
Shows improperly setup Bill Validators
Location numbers
Bill Validator
Shows acceptance rate and other technical
acceptance/
statistics of validators
performance
Version Indicates software versions of all validators

Group Shows group each Bill Validator belongs to

Daily Dashboard Reports

Access Dashboard Export Search

- 22 -
 Printer Setup and Reports

Host Machine

Future Logic (Gen2 Universal)

Customer IGT WMS Others

Printer Harness
150-00106-100 150-00199-100 150-00123-100
Cable Part Number

CashCode One™
Harness Cable Part FL85.00.056
Number

Printer Software Rev. J and above

BV Control
58 + 65 + 65 +
Software

Additional printer template required, inquire for details.

Printer Harness Cable one™ Harness Cable Printer Harness

Cable
To Host
FL85.00.056

Future Logic CashCode one™

Printer Bill Validator

- 23 -
 Printer Setup and Reports

Host Machine

Transact (Ithaca 950)

Customer All

Printer Harness
95-11683L
Cable Part Number

CashCode Harness
Not Required
Part Number

Printer SW SP 3 +

BV Control SW 58 + 66 + 66 +

CashCode one™ Host

Printer Harness Cable (30cm) Cable (3m)

To Host

Transact Printer CashCode one™

Bill Validator

- 24 -
The oneCheck™ printer can generate three different reports (these are
either printer automatically or manually, based on setting from page 21):

REPORT TYPE DETAILS EXAMPLE

Last Five Bills

Press validator latch 2 times
inserted Report
within 6 seconds
(Bill Dispute)

Bill Validator
and Printer Press validator latch 4 times
Performance within 6 seconds
Report
1. Hold validator latch for 2
seconds and release
Cashbox Audit
2. Insert the report into validator
and
to stack in the cashbox
Performance
(4 red flashes)
Report
(CAPR) 3. Report must be scanned with
2D barcode scanner during soft
count process
* Patent Pending

Cash Management

1. PRINT CAPR 2. DROP

4. ANALYZE 3. SCAN and

REPORT ASSET

Following Currency Counter or Sorter Systems are Compatible

with oneCheck™ or oneTrack™: Cummins, DeLaRue and G&D

- 25 -
 CAPR Guidelines

EVENT RECOMMENDED DIRECTIONS

1. Ensure DIP switch is set to oneCheck™
(see page 10)
2. Install the validating head and
New Slot Machine
power up the Bill Validator
or New Validator
3. Initialize the unit as specified on p. 21
4. Install the cashbox inside the
validator
1. Remove validating head, and then the
cashbox, as necessary to clear the jam
Jam in Bill 2. Re-install the cashbox followed by
Validator the validating head
3. To swap the Bill Validating heads
follow steps in next event
Exchanging 1. Print CAPR report and stack report
validating head inside cashbox
from one machine 2. Remove the Bill Validating head
to another 3. Initialize the unit as specified on p. 21
1. Print CAPR report and stack report
Cashbox Full/
inside cashbox
Emergency Drop
2. Replace with a new Cold Box
1. Print CAPR report and stack report
Standard Drop inside cashbox
Operation 2. Simply replace Hot Box with new Cold
Box only when unit is powered up

To find out about all neCheckTM benefits, please visit the

oneCheck TM section on the CashCode oneTM page at:
http://elearning.cashcode.com/

- 26 -
EVENT DIRECTIONS
Drop during 1. Validator should be powered up before
power cycle down removing the cashbox
or Machine out of 2. Print CAPR report and stack report
order inside cashbox
1. Remove cashbox while Bill Validator is
Moving the Slot powered on and follow CAPR procedure
Machine. 2. In the new location, power on the Bill
Validator and assign new location number
1. Scan each CAPR as collected from cashbox
Scanning of on oneCheckTM database using a 2D
multiple CAPR barcode scanner (green signal will appear)
reports per 2. Proceed to counter/sorter machine with
Cashbox into all cashbox contents
Database 3. Follow procedure recommended by
counter/sorter manufacturer
1. Follow CAPR procedure
2. Remove Hot Box and replace with a
Cold Box
Bill 3. Follow software update procedure
Validator with cashbox inside the Bill Validator
Firmware 4. Reassign machine location number
Update 5. Use CCNavigator or CCNET Stat Utility to
verify that the Machine and Location
numbers as well as the cashbox size are
correct

For oneCheckTM back office documentation see:

http://support.cashcode.com

- 27 -
 List of Available Harnesses
Crane Part Number Gaming OEMs & Platforms
FL85.00.011 Spielo (oneCheck™)
FL85.00.012 Cole Harness (oneCheck™)
FL85.00.013-01 Aristocrat MK-VI (US oneCheck™)
FL85.00.013-02 Aristocrat MK-VI (US Universal)
FL85.00.014 oneCheck™ add on Harness
FL85.00.015 AGS Harness
FL85.00.016-02 Atronic Harness (oneCheck™)
FL85.00.017-01 Konami K2V Harness (oneCheck™)
FL85.00.018 Novomatic Coolfire2
FL85.00.019-01 Star Games Harness (oneCheck™)
FL85.00.020 Novomatic CoolFire1
FL85.00.021-01 / -02 Aristocrat Viridian (oneCheck™) / (Universal)
FL85.00.022 Aristocrat MKVI Excite
FL85.00.023-01 West Money (oneCheck™)
FL85.00.026-01 VGT & Aruze (US/Aus oneCheck™)
FL85.00.028-01 Aruze (Non - US Aus oneCheck™)
FL85.00.028-02 Aruze (Non - US Aus Universal)
FL85.00.031-01 Konami Podium (oneCheck™)
FL85.00.033-01 / -02 Konami Adv 5 (oneCheck™) / (Universal)
FL85.00.034 Gold Club
FL85.00.035 / -02 Bally (oneCheck™) / (Universal)
FL85.00.036-01 Ainsworth A560 (oneCheck™)
FL85.00.037-01 Ainsworth Ambassador (oneCheck™)
FL85.00.039 IGT (Old Revision - 2012)
FL85.00.039-02 IGT (New Revision - 2013)
FL85.00.049-01 Entropy (oneCheck™)
FL85.00.050-01 WMS Bluebird 2 / XD (oneCheck™)
FL85.00.055-01 GDS (oneCheck™)
FL85.00.056 Future Logic printer Add On (oneCheck™)

Mating kit can be ordered using P/N: OPT-MKFLS-24

- 28 -
Visit us at http://elearning.cashcode.com for:
- Online product training
- Available product configurations
- Product service and maintenance videos

Visit us at http://support.cashcode.com for:

- Product documentation
- Online technical support
- Service center information
 CashCode

600 900 1000 2500

E-Mail: [email protected]
E-Mail: for RMA: [email protected]
or call our Technical Support line at:
+1 905-303-8874 or toll free in NA 1-800-584-2633

2720 Steeles Ave. West, Concord, ON Canada L4K 4S3