JetNet 4508 / 4508f Series

Industrial 8-port Managed Fast Ethernet Switch

User’s Manual

Version 1.13
Firmware V1.1a

www.korenix.com

1
 JetNet 4508 / 4508f Series
Industrial 8-port Managed Fast Ethernet Switch
User’s Manual

Copyright Notice

Copyright © 2012 Korenix Technology Co., Ltd.

All rights reserved.
Reproduction in any form or by any means without permission is prohibited.

2
Declaration of CE
This product has passed the CE certification for environmental
specifications. Test conditions for passing included the equipment being
operated within an industrial enclosure. In order to protect the product
from being damaged by ESD (Electrostatic Discharge) and EMI leakage,
we strongly recommend the use of CE-compliant industrial enclosure
products.

Federal Communications Commission (FCC) Statement

This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications. Operation of
this equipment in a residential area is likely to cause harmful interference
in which case the user will be required to correct the interference at his
expense.

The user is cautioned that changes and modifications made to the

equipment without approval of the manufacturer could void the user's
authority to operate this equipment.

3
Verification of Conformity for Railway EMC

4
 Index
1 Introduction .............................................................................................2
1.1 Overview ........................................................................................ 2
1.2 Major Features ............................................................................... 2
1.3 Package List .................................................................................. 3
2 Hardware Installation..............................................................................4
2.1 Hardware Introduction .................................................................... 5
2.2 Wiring the Power Inputs ............................................................... 10
2.3 Wiring Digital Input ....................................................................... 12
2.4 Wiring Relay Output ..................................................................... 12
2.5 Wiring Earth Ground .................................................................... 13
2.6 Wiring Fast Ethernet RJ-45 Ports................................................. 14
2.7 Wiring Fast Ethernet Fiber port (JetNet 4508f) ............................ 15
2.8 Wiring RS-232 Console Cable ..................................................... 15
2.9 DIN-Rail Mounting Installation ...................................................... 16
3 Preparation for Management ...............................................................17
3.1 Preparation for Serial Console ..................................................... 18
3.2 Preparation for Web Interface ...................................................... 19
3.3 Preparation for Telnet Console ..................................................... 22
4 Feature Configuration ..........................................................................25
4.1 Command Line Interface Introduction .......................................... 26
4.2 Basic Setting ................................................................................ 31
4.3 Port Configuration ........................................................................ 50
4.4 Network Redundancy ................................................................... 60
4.5 VLAN............................................................................................ 80
4.6 Private VLAN ............................................................................... 88
4.7 Traffic Prioritization....................................................................... 95
4.8 Multicast Filtering ....................................................................... 100
4.9 SNMP......................................................................................... 105
4.10 Security ...................................................................................... 109
4.11 Warning ...................................................................................... 116
4.12 Monitor and Diag ........................................................................ 124
4.13 Device Front Panel .................................................................... 133
4.14 Save to Flash ............................................................................. 134
4.15 Logout ........................................................................................ 135
5 Appendix .............................................................................................136
5.1 Product Specifications ................................................................ 136
5.2 Korenix Private MIB ................................................................... 141
5.3 Modbus TCP protocol ................................................................ 142
5.4 Revision History ......................................................................... 154
5.5 About Korenix ............................................................................ 155
1 Introduction

Welcome to Korenix JetNet 4508 / 4508f Series Industrial 8-port

Managed Fast Ethernet Switch User Manual. Following topics are
covered in this chapter:
1.1 Overview
1.2 Major Features
1.3 Package Checklist

1.1 Overview

The JetNet 4508 / 4508f series are 8-port industrial managed Fast Ethernet
Switch designed with advanced Layer 2 management features and high
system reliability, including MSR and MSTP network redundancy
technologies, for ensuring real-time and high quality connectivity in various
networking applications. The Ethernet switches includes 6 10/100Mbps
plus 2 100Mbps Fast Ethernet ports in RJ-45 connectors (JetNet 4508) or 6
10/100Mbps Fast Ethernet ports plus 2 100Mbps Fast Ethernet Fiber ports.;
Both of switches adopted 32Gbps switch fabric to provide real time
non-blocking transmission performance for satisfying the needs of high
bandwidth data transmission requiring applications while ensuring traffic
switching without data loss. Besides, the new system design includes a
hardware based watchdog timer for keeping the operating system live. It
also provides power redundancy with wide range DC10V~60V inputs for
ensuring the power continuity in the system. Combining the outstanding L2
management features along with the LLDP and the JetView Pro Intelligent
NMS into the ruggedized design with IP31 enclosure and -25~70°C
(regular version) and -40~75°C (-w version) wide operating temperature,
JetNet 4508 series provide highly reliable and secure data transmission
under severe industrial environments.

1.2 Major Features

The JetNet Managed Switch has the following features:

„6 10/100TX ports with Auto MDI/MDI-X
„2 100Base-TX (JetNet 4508), 2 100Base-FX (JetNet 4508f)
„32Gbps Non-Blocking, 8K MAC address table

2
 „Multiple Super Ring (recovery time <5ms), Rapid Dual Homing,
Multiple Ring, and MSTP / RSTP
„IEEE 1588 Precision Time Protocol for precise time synchronization
„VLAN, Private VLAN, QinQ, GVRP, QoS, IGMP Snooping V1/V2/V3,
Rate Control, Port Trunking, LACP, Online Multi-Port Mirroring
„IEEE 802.1AB LLDP and JetView Pro i2NMS for auto-topology and
group management
„Supports SNMP, Multiple Language Web UI, Telnet In-Band, Serial
Out-Band Management
„Supports ModBus TCP/Client function for HMI system.
„Embedded Hardware Watchdog for System Auto Rescue
„Dual DC10~60V Power Inputs with Redundancy
„Software configurable Alarm Output
„IP31 rugged aluminum case
„Operating temperature:
-25~70°C (JetNet 4508), -10~70°C (JetNet 4508f) and -40~75°C
(JetNet 4508-w / JetNet 4508f-w)
* If there is any specification change, please refere to the Web site or contact
your sales window.

The detail spec is listed in Appendix

Note-1: those certifications are pending for special project request, please
contact your sales widnow.

1.3 Package List

Korenix JetNet 4508 Series products are shipped with following items:
JetNet 4508 x1 or JetNet 4508f x1
One DIN-Rail clip (attached to the switch)
One RS-232 DB-9 to RJ-45 console cable
CD User manual x 1
Quick Installation Guide (QIG)

DB-9 to RJ-45 CD User QIG

JetNet 4508/ JetNet 4508f Cable Manual

If any of the above items is missing or damaged, please contact your local
sales representative.
3
2 Hardware Installation
This chapter includes hardware introduction, installation and
configuration information. Following topics are covered in this chapter:
2.1 Hardware Introduction
Dimension
Panel Layout
Bottom View
2.2 Wiring Power Inputs
2.3 Wiring Digital Input
2.4 Wiring Relay Output
2.5 Wiring Ethernet Ports
2.6 Wiring RS-232 console cable
2.7 DIN-Rail Mounting Installation

4
2.1 Hardware Introduction
Dimension of JetNet 4508
JetNet 4508 Industrial 8-port managed Fast Ethernet Switch dimension is:
55 (W) x 149 (H) x 131.2 (D) / with DIN Rail Clip
55 (W) x 149 (H) x 120.6 (D) / without DIN Rail Clip

5
 Dimension of JetNet 4508f
JetNet 4508f Industrial 6-port plus 2 100Mbps Fiber managed Fast Ethernet
Switch dimension is:
55 (W) x 149 (H) x 131.2 (D) / with DIN Rail Clip
55 (W) x 149 (H) x 120.6 (D) / without DIN Rail Clip

6
Front Panel Layout- JetNet 4508
The front panel of JetNet 4508 includes 8 10/100Mbps Fast Ethernet RJ-45
ports, one RS-232 serial console in RJ-45 type connector, one reset button
and several of LED indicators for the system and port diagnostic. The JetNet
4508 front panle shows as following diagram.

7
 Front Panel Layout- JetNet 4508f
The front panel of JetNet 4508f includes 6 10/100Mbps Fast Ethernet RJ-45
ports (port 1~6), 2 Fast Ethernet fiber ports (port 7, 8), one RS-232 serial
console in RJ-45 type connector, one reset button and several of LED
indicators for the system and port diagnostic. The JetNet 4508f front panle
shows as following diagram.

The LED function is decribed as following table:

LED Function Behaviors
Power 1,2 Indicates the power input status On: the input connector is on applying
power.
SYS Indicates the system operating status On: System is ready to operating
DI Indicates the digital input status On: High level signal is applied
DO Indicates the digital output (Relay Red On: the output is formed close
output) status circuit
R.S. Indicates the ring operating status. Normal (Green on), Abnormal (Yellow
on), wrong ring port is connected
(Green blinking), one of device’s ring
path is broken (Yellow blinking)
Link/active Indicated the traffic status and link On: port is linked with partner.

8
 status Blinking: the port is on transmitting or
receiving data.

Bottom View
The bottom view of the JetNet 4508 / JetNet 4508f consists of two terminal
block connectors with two DC power inputs, one Digital Input (DI), one Relay
Output (DO) and one Chassis Grounding screw.

9
2.2 Wiring the Power Inputs
Follow below steps to wire JetNet 4508 / 4508f redundant DC power
inputs.

1. Insert positive and negative wires into V+ and V- contacts respectively of

the terminal block connector
2. Tighten the wire-clamp screws to prevent DC wires from being loosened.
3. Power 1 and Power 2 support power redundancy and polarity reverse
protect function. That means with wrong polarity, the system won’t work.
4. Positive and negative power system inputs are both accepted, but Power
1 and Power 2 must apply with same mode as following figures.

Positive Power wiring

Negative Power wiring

10
 Note 1: It is a good practice to turn off input and load power, and to unplug
power terminal block before making wire connections. Otherwise, your
screwdriver blade can inadvertently short your terminal connections to the
grounded enclosure.
Note 2: The range of the suitable electric wire is from 12 to 24 AWG.
Note 3: If the 2 power inputs are connected, JetNet Switch will be powered
from the highest connected voltage. The unit will alarm for loss of power,
either PWR1 or PWR2 and auto backup with each other.
Note 4: Uses the UL Listed Power supply with output Rating 10-60 Vdc,
minimum 2 A. Here, we recommended use DC 24V as the operating voltage.
Note 5: Once the system powering on, the system diagnostic LEDs will
activate as the sequence shown in the following table:
Indicators Stage 1 Stage 2 Stage 3 Stage 4 Stage 5 Stage 6
Power LED On On On On On On
DI Off On Off Off Off Off
DO Off Off On Off Off Off
R.S. Off Off Off On Off Off
SYS Off Off Off Off Off On
Description Power on Ex. Booter Ld. firmware Ex. firmware System booting System Ready

By those LED indicators, we can know the exactly stage is performed during
the system power on.

11
2.3 Wiring Digital Input
JetNet 4508 series provide one digital input. It allows users to connect the
termination units’ digital output and manage/monitor the status of the connected
unit. The Digital Input pin can be pulled high or low; thus the connected
equipments can actively drive these pins high or low. The embedded software
UI allows you to read and set the value to the connected device.
The power input voltage of logic low is DC 0~10V. Logic high is DC
11~30V.
.

2.4 Wiring Relay Output

JetNet 4508 series provide one Digital output, also known as Dry Relay
Output. The relay contacts are energized (open) for normal operation and
will close for fault conditions. The fault conditions include power failure,
Ethernet port link break or other pre-defined events which can be
configured in JetNet 4508 Web user interface.

12
2.5 Wiring Earth Ground
To ensure the system will not be damaged by noise or any electrical shock,
we suggest you to make exact connection with JetNet 4508 series with
Earth Grounding.
On the bottom side of JetNet 4508 series, there is one earth ground screw.
Loosen the earth ground screw by screw drive; then tighten the screw after
earth ground wire is well connected.
Without the exact system chassis grounding, the communication may
intereferred by the external noise, such as lighting, fast electrical filed
transient or electrostatic discharge.

13
2.6 Wiring Fast Ethernet RJ-45 Ports
The JetNet 4508 series adopts several of RJ-45 connectors which support
10/100Base-TX with link speed auto negotiation and auto MDI/MDI-X
functions.
All the RJ-45 ports will auto-detect the signal from connected devices to
negotiate the link speed and duplex mode. Auto MDI/MDIX allows users to
connect another switch, hub or workstation without changing straight
through or crossover cable.
Note: that crossover cables simply cross-connect the transmit lines at
each end to the received lines at the opposite end.

Pin MDI-X Signals MDI Signals

1 RD+ TD+
2 RD- TD-
3 TD+ RD+
6 TD- RD-

Connect one side of an Ethernet cable into any switch port and connect the
other side to your attached device. The LNK LED will light up when the
cable is correctly connected. Refer to the LED Indicators section for
descriptions of each LED indicator. Always make sure that the cables
between the switches and attached devices (e.g. switch, hub, or
workstation) are less than 100 meters (328 feet).
The supported cable types listed as below:
100Base-TX: 4-pair UTP/STP Cat. 5 Cable, EIA/TIA-568B 100-ohm (100 meters)
10Base-T: 4-pair UTP/STP Cat.3, 4 cable, EIA/TIA-568B 100-ohm (100meters)

14
 2.7 Wiring Fast Ethernet Fiber port (JetNet 4508f)
JetNet 4508f equipped 2 ports fiber which compliance with IEEE 802.3
100Base-FX standard and supports multi-mode or single mode fiber cable.
The fiber connector supports SC type connector and for the other type
connector, please contacts your Korenix distributor for more information.
To ensure the quality of connection, the specifications of cable and fiber
port must matched; with wrong fiber cable may caused the communication
does not work well.The following information is the specification includes
suitable cable and the characteristics of fiber port.

Model TX power RX sensitivity Wavelength Fiber Cable

JetNet 4508f-s, -8~-15 dBm -31~-14dBm 1310nm 8~10/125 um
30KM Single mode
JetNet 4508f-m -14~-31 dBm -14~-31 dBm 1310nm 50~62.5/125um
2KM Multi-mode

2.8 Wiring RS-232 Console Cable

There is one RS-232 DB-9 to RJ-45 cable shipped with the box. Connects
the DB-9 connector to the COM port of your PC, open Terminal tool and
configure the serial communication parameter to 9600, N, 8, 1. (Baud Rate:
9600bps / Parity: None / Data length: 8bits / Stop Bit: 1) Then you can
access CLI interface by console able.
Note: If you lost the cable, please contact with your sales or follow the pin
assignment to buy a new one. The Pin assignment spec is listed following.

RJ-45 Pin DB-9 Pin Description DB-9 Female Connector

1 8 N/A
2 9 N/A
3 2 TxD
4 1 N/A
5 5 GND
6 3 RxD
7 4 N/A
8 7 N/A

15
2.9 DIN-Rail Mounting Installation
The DIN-Rail clip is already screwed tighten on the rear side of JetNet
JetNet 4508/ JetNet 4508f when shipping. If the DIN-Rail clip is not
screwed on the JetNet 4508/ JetNet 4508f, please contact your distributor
to get the DIN rail clip set. The DIN rail clip supports EN50022 standard. In
the diagram following includes the dimension of EN50022 DIN rail for your
refer.

Follow the steps below to mount JetNet Managed Switch to the DIN-Rail
track:
1. First, insert the DIN-Rail track upper side into the upper end of
DIN-Rail clip.
2. Lightly push the bottom of DIN-Rail clip into the track.
3. Check if DIN-Rail clip is tightly attached on the track.
4. To remove JetNet 4508/ JetNet 4508f from the track, reverse the
steps above.
Notes: The DIN Rail should compliance with DIN EN50022 standard. Using wrong
DIN rail may cause system install unsafe.

16
3 Preparation for Management
JetNet 4508 / 4508f series Industrial Managed Fast Ethernet Switch
provides both in-band and out-band configuration methods. You can
configure the switch via RS232 console port via serial cable attached in
the package if you don’t attach your admin PC to your network, or if you
lose network connection to the target JetNet Switch. This is so-called
out-band management. It wouldn’t be affected by network performance.
The in-band management means you can remotely manage the switch
via the Ethernet network. You can choose Telnet or Web-based
management. You just need to know the device’s IP address and you can
remotely connect to its embedded HTTP web pages or Telnet console.
Following topics are covered in this chapter:
3.1 Preparation for Serial Console
3.2 Preparation for Web Interface
3.3 Preparation for Telnet console

17
3.1 Preparation for Serial Console
In package, Korenix attached one RS-232 DB-9 to RJ-45 console cable.
Please attach RS-232 DB-9 connector to your PC COM port, connect
RJ-45 to the Console port of the JetNet Switch. If you lose the cable,
please follow the console cable PIN assignment to find one. (Refer to
session 2.8).
1. Go to Start -> Program -> Accessories -> Communication -> Hyper
Terminal
2. Give a name to the new console connection.
3. Choose the COM name
4. Select correct serial settings. The serial settings of JetNet 4508 /
4508f are as below:
Baud Rate: 9600 / Parity: None / Data Bit: 8 / Stop Bit: 1
5. After connected, you can see Switch login request.
6. Login the switch. The default username is “admin”, and password is
“admin”.

Boot Loader Rev 1.0.0.4 for JetNet4508f (Sep 2 2010 - 17:48:54)

Loading firmware ...

Excuting firmware ...

Booting ........................................................................

....

Validate hardware : Success

System start type : Watchdog reset

Switch MAC address : 00:12:77:FF:00:00

Port6 Link Change to UP

Port5 Link Change to UP

Loading system : Success

Port5 Link Change to DOWN

RF's TestinPort5 Link Change to UP

g login:

18
3.2 Preparation for Web Interface
JetNet 4508/4508f provides HTTP Web Interface and Secured HTTPS
Web Interface for web management. The Web user interface supports 2
languages – English and simplified Chinese, you can slelect language
type while performs login process.
3.2.1 Web Interface
Korenix web management page is developed by JAVA. It allows you to
use a standard web-browser such as Microsoft Internet Explorer, or
Mozila, to configure and interrogate the switch from anywhere on the
network.
Before you attempt to use the embedded web interface to manage switch
operation, verify that your JetNet 4508 / 4508f is properly installed on
your network and that every PC on this network can access the switch via
the web browser.
1. Verify that your network interface card (NIC) is operational, and that
your operating system supports TCP/IP protocol.
2. Wire DC power to the switch and connect your switch to your
computer.
3. Make sure that the switch default IP address is 192.168.10.1.
4. Change your computer IP address to 192.168.10.2 or other IP
address which is located in the 192.168.10.x (Network Mask:
255.255.255.0) subnet.
5. Switch to DOS command mode and ping 192.168.10.1 to verify a
normal response time.
Launch the web browser and Login.
6. Launch the web browser (Internet Explorer or Mozila Firefox) on the
PC.
7. Type http://192.168.10.1 (or the IP address of the switch). And then
press Enter.
8. The login screen will appear next.
9. Key in user name and the password. Default user name and
password are both admin.
10. Select language type, the default is English. This feature is available
from firmware v1.1.

19
 Click on Enter or OK. Welcome page of the web-based management
interface will then appear.

Once you enter the web-based management interface, you can freely
change the JetNet’s IP address to fit your network environment.

Note 1: IE 5.0 or later versions do not allow Java applets to open sockets
by default. Users have to directly modify the browser settings to
selectively enable Java applets to use network ports.
Note 2: The Web UI connection session of JetNet Switch will be logged
out automatically if you don’t give any input after 30 seconds. After logged
out, you should re-login and key in correct user name and password
again.

3.2.2 Secured Web Interface

Korenix web management page also provides secured management
HTTPS login. All the configuration commands will be secured and will be
hard for the hackers to sniff the login password and configuration
commands.
Launch the web browser and Login.
1. Launch the web browser (Internet Explorer or Mozila Firefox) on the
PC.
2. Type https://192.168.10.1 (or the IP address of the switch). And then
press Enter.
3. The popup screen will appear and request you to trust the secured
HTTPS connection distributed by JetNet 4508/JetNet 4508f first.
Press Yes to trust it. ( Uses JeNet 5010G sample)

20
4. The login screen will appear next.

5. Key in the user name and the password. The default user name and
password is admin.
6. Click on Enter or OK. Welcome page of the web-based management
interface will then appear.
7. Once you enter the web-based management interface, all the
commands you see are the same as what you see by HTTP login.

21
3.3 Preparation for Telnet Console
3.3.1 Telnet
Korenix JetNet 4508 / 4508f supports Telnet console. You can connect to
the switch by Telnet and the command lines are the same as what you
see by RS-232 console port. Below are the steps to open Telnet
connection to the switch.

1. Go to Start -> Run -> cmd. And then press Enter

2. Type the Telnet 192.168.10.1 (or the IP address of the switch). And
then press Enter
3.3.2 SSH (Secure Shell)
Korenix JetNet 4508 / 4508f also support SSH console. You can remotely
connect to the switch by command line interface. The SSH connection
can secure all the configuration commands you sent to the switch.
SSH is a client/server architecture while JetNet 4508 / 4508f is the SSH
server. When you want to make SSH connection with the switch, you
should download the SSH client tool first.
SSH Client
There are many free, sharewares, trials or charged SSH clients you can
find on the internet. Fox example, PuTTY is a free and popular
Telnet/SSH client. We’ll use this tool to demonstrate how to login JetNet
by SSH. Note: PuTTY is copyright 1997-2006 Simon Tatham.

Download PuTTY:
http://www.chiark.greenend.org.uk/~sgtatham/putty/download.html

The copyright of PuTTY

22
1. Open SSH Client/PuTTY
In the Session configuration, enter the Host Name (IP Address of your
JetNet Switch) and Port number (default = 22). Choose the “SSH”
protocol. Then click on “Open” to start the SSH session console.
(The sample’s IP address is 192.168.10.13)

2. After click on Open, then you can see the cipher information in the
popup screen. Press Yes to accept the Security Alert.

3. After few seconds, the SSH connection to JetNet 4508 / 4508f is

opened. You can see the login screen as the below figure.

23
4. Type the Login Name and its Password. The default Login Name and
Password are admin / admin.
5. All the commands you see in SSH are the same as the CLI
commands you see via RS232 console. The next chapter will
introduce in detail how to use command line to configure the switch.

24
4 Feature Configuration
This chapter explains how to configure JetNet 4508/4508f software
features. There are four ways to access the switch: Serial console, Telnet,
Web browser and SNMP.
JetNet 4508/4508f series Industrial Managed Switch provides both in-band
and out-band configuration methods. You can configure the switch via
RS-232 console cable if you don’t attach your admin PC to your network, or
if you lose the network connection to your JetNet JetNet 4508/JetNet 4508f.
This is so-called out-band management. It wouldn’t be affected by the
network performance.
The in-band management means you can remotely manage the switch via
the network. You can choose Telnet or Web-based management. You just
need to know the device’s IP address. Then you can remotely connect to its
embedded HTML web pages or Telnet console.
Korenix web management page is developed by JAVA. It allows you to use
a standard web-browser such as Microsoft Internet Explorer, or Mozila, to
configure and interrogate the switch from anywhere on the network.
Note: IE 5.0 or later versions do not allow Java applets to open sockets by
default. Users have to directly modify the browser settings to selectively
enable Java applets to use network ports.

Following topics are covered in this chapter:

4.1 Command Line Interface (CLI) Introduction
4.2 Basic Setting
4.3 Port Configuration
4.4 Network Redundancy
4.5 VLAN
4.6 Traffic Prioritization
4.7 Multicast Filtering
4.8 SNMP
4.9 Security
4.10 Warning
4.11 Monitor and Diag
4.12 Device Front Panel
4.13 Save
4.14 Logout

25
4.1 Command Line Interface Introduction
The Command Line Interface (CLI) is the user interface to the switch’s
embedded software system. You can view the system information, show
the status, configure the switch and receive a response back from the
system by keying in a command.
There are some different command modes. Each command mode has its
own access ability, available command lines and uses different command
lines to enter and exit. These modes are User EXEC, Privileged EXEC,
Global Configuration, (Port/VLAN) Interface Configuration modes.
User EXEC mode: As long as you login the switch by CLI. You are in the
User EXEC mode. You can ping, telnet remote device, and show some
basic information.
Type enable to enter next mode, exit to logout. ? to see the command list

Switch>
enable Turn on privileged mode command
exit Exit current mode and down to previous mode
list Print command list
ping Send echo messages
quit Exit current mode and down to previous mode
show Show running system information
telnet Open a telnet connection
traceroute Trace route to destination

Privileged EXEC mode: Press enable in the User EXEC mode, then you
can enter the Privileged EXEC mode. In this mode, the system allows you
to view current configuration, reset default, reload switch, show system
information, save configuration…and enter the global configuration mode.
Type configure terminal to enter next mode, exit to leave. ? to see the
command list

Switch#
archive manage archive files
clear Reset functions
clock Configure time-of-day clock
configure Configuration from vty interface
copy Copy from one file to another
debug Debugging functions (see also 'undebug')
disable Turn off privileged mode command
end End current mode and change to enable mode
exit Exit current mode and down to previous mode
list Print command list
more Display the contents of a file
no Negate a command or set its defaults
ping Send echo messages
quit Exit current mode and down to previous mode
reboot Reboot system
reload copy a default-config file to replace the current one
show Show running system information
telnet Open a telnet connection
terminal Set terminal line parameters
traceroute Trace route to destination 26
write Write running configuration to memory, network, or terminal
Global Configuration Mode: Press configure terminal in privileged
EXEC mode. You can then enter global configuration mode. In global
configuration mode, you can configure all the features that the system
provides you.
Type interface IFNAME/VLAN to enter interface configuration mode, “exit
“to leave this configuration level and “? “ to list all of commands.

Available command lists of global configuration mode.

Switch# configure terminal

Switch(config)#
access-list Add an access list entry
administrator Administrator account setting
arp Set a static ARP entry
clock Configure time-of-day clock
default Set a command to its defaults
end End current mode and change to enable mode
exit Exit current mode and down to previous mode
gvrp GARP VLAN Registration Protocol
hostname Set system's network name
interface Select an interface to configure
ip IP information
lacp Link Aggregation Control Protocol
list Print command list
log Logging control
mac Global MAC configuration subcommands
mac-address-table mac address table
mirror Port mirroring
no Negate a command or set its defaults
ntp Configure NTP
password Assign the terminal connection password
qos Quality of Service (QoS)
relay relay output type information
smtp-server SMTP server configuration
snmp-server SNMP server
spanning-tree spanning tree algorithm
super-ring super-ring protocol
trunk Trunk group configuration
vlan Virtual LAN
warning-event Warning event selection
write-config Specify config files to write to

(Port) Interface Configuration: Press interface IFNAME in global

configuration mode. You can then enter interface configuration mode. In
this mode, you can configure port settings.
The port interface name for Fast Ethernet port 1~8 are fa1~fa8. Typing in
the interface name accordingly when you want to enter certain interface
configuration mode.

Type “exit” to leave this current level.

Type “? “ to show the command list

27
Available command lists of the global configuration mode.

Switch(config)# interface fa1

Switch(config-if)#
acceptable Configure 802.1Q acceptable frame types of a port.
auto-negotiation Enable auto-negotiation state of a given port
description Interface specific description
duplex Specify duplex mode of operation for a port
end End current mode and change to enable mode
exit Exit current mode and down to previous mode
flowcontrol Set flow-control value for an interface
garp General Attribute Registration Protocol
ingress 802.1Q ingress filtering features
lacp Link Aggregation Control Protocol
list Print command list
loopback Specify loopback mode of operation for a port
mac MAC interface commands
mdix Enable mdix state of a given port
no Negate a command or set its defaults
qos Quality of Service (QoS)
quit Exit current mode and down to previous mode
rate-limit Rate limit configuration
shutdown Shutdown the selected interface
spanning-tree spanning-tree protocol
speed Specify the speed of a Fast Ethernet port or a Gigabit
Ethernet port.
switchport Set switching mode characteristics

(VLAN) Interface Configuration: Press interface VLAN VLAN-ID in

global configuration mode. You can then enter VLAN interface configuration
mode. In this mode, you can configure the settings for the specific VLAN.
The VLAN interface name of VLAN 1 is VLAN 1, VLAN 2 is VLAN 2…
Type exit to leave the mode. Type ? to see the available command list.
The command lists of the VLAN interface configuration mode.

Switch(config)# interface vlan 1

Switch(config-if)#
description Interface specific description
end End current mode and change to enable mode
exit Exit current mode and down to previous mode
ip Interface Internet Protocol config commands
list Print command list
no Negate a command or set its defaults
quit Exit current mode and down to previous mode
shutdown Shutdown the selected interface

28
 Summary of the 5 command modes.

Command Main Function Enter and Exit Method Prompt

Mode

User EXEC This is the first level of access. Enter: Login successfully Switch>

User can ping, telnet remote Exit: exit to logout.

device, and show some basic Next mode: Type enable to
information enter privileged EXEC mode.

Privileged In this mode, the system allows Enter: Type enable in User Switch#

EXEC you to view current configuration, EXEC mode.

reset default, reload switch, show Exec: Type disable to exit to

system information, save user EXEC mode.

configuration…and enter global Type exit to logout

configuration mode. Next Mode: Type configure

terminal to enter global

configuration command.

Global In global configuration mode, you Enter: Type configure Switch(config)#

configuration can configure all the features that terminal in privileged EXEC

the system provides you mode

Exit: Type exit or end or press

Ctrl-Z to exit.

Next mode: Type interface

IFNAME/ VLAN VID to enter

interface configuration mode

Port In this mode, you can configure Enter: Type interface IFNAME Switch(config-if)#
Interface port related settings. in global configuration mode.

configuration Exit: Type exit or Ctrl+Z to

global configuration mode.

Type end to privileged EXEC

mode.

VLAN Interface In this mode, you can configure Enter: Type interface VLAN Switch(config-vlan)#

Configuration settings for specific VLAN. VID in global configuration

mode.

Exit: Type exit or Ctrl+Z to

global configuration mode.

Type end to privileged EXEC

mode.

29
Here are some useful commands for you to see these available commands.
Save your time in typing and avoid typing error.

? To see all the available commands in this mode. It helps you to see the
next command you can/should type as well.

Switch(config)# interface ?
IFNAME Interface's name
vlan Select a vlan to configure

(Character) ? To see all the available commands starts from this

character.

Switch(config)# a?
access-list Add an access list entry
administrator Administrator account setting
arp Set a static ARP entry

Tab This tab key helps you to input the command quicker. If there is only
one available command in the next, clicking on tab key can help to finish
typing soon.

Switch# co (tab) (tab)

Switch# configure terminal

Switch(config)# ac (tab)
Switch(config)# access-list

Ctrl+C To stop executing the unfinished command.

Ctrl+S To lock the screen of the terminal. You can’t input any command.
Ctrl+Q To unlock the screen which is locked by Ctrl+S.
Ctrl+Z To exit configuration mode.

Alert message when multiple users want to configure the switch. If the
administrator is in configuration mode, then the Web users can’t change the
settings. JetNet 4508/4508f allows only one administrator to configure the
switch at same time.

30
4.2 Basic Setting
The Basic Setting group provides you to configure switch information, IP
address, User’s name/Password of the system. It also allows you to do
firmware upgrade, backup and restore configuration, reload factory default, and
reboot the system.

Following commands are included in this group:

4.2.1 Switch Setting
4.2.2 Admin Password
4.2.3 IP Configuration
4.2.4 Time Setting
4.2.5 DHCP Server
4.2.6 Backup and Restore
4.2.7 Firmware Upgrade
4.2.8 Factory Default
4.2.9 System Reboot
4.2.10 CLI Commands for Basic Setting

4.2.1 Switch Setting

You can assign System name, Location, Contact and view system information.
Figure 4.2.1.1 – Web UI of the Switch Setting

(Sampling device setting for System Location is “PM-Richard” and System Contact is
“PM-Richard ext200)

System Name: You can assign a meaningful name to the device. The available
characters you can input is 64. After you configure the name, CLI system will
select the first 12 characters as the name in CLI system.

31
 System Location: You can specify the switch’s physical location here. The
available characters you can input are 64.
System Contact: You can specify contact people here. You can type the name,
mail address or other information of the administrator. The available characters
you can input are 64.
System OID: The SNMP object ID of the switch. You can follow the path to find
its private MIB in MIB browser. (Note: When you attempt to view private MIB,
you should compile private MIB files into your MIB browser first.)
System Description: the real product model name of this product.
Firmware Version: Display the firmware version installed in this device.
MAC Address: Display unique hardware address (MAC address) assigned by
the manufacturer.
Product Name: Display the Switch’s model name
Serial Number: Display the Switch’s serial number
Manufacture Date: Display the switch’s production date.

Once you finish the configuration, click on Apply to apply your settings.
Note: Always remember to select Save to save your settings. Otherwise, the
settings you made will be lost when the switch is powered off.

4.2.2 Admin Password

You can change the user name and the password here to enhance security

Figure 4.2.2.1 Web UI of the Admin Password

Name: You can key in new user name here. The default setting is admin.
Password: You can key in new password here. The default setting is admin.
Confirm Password: You need to type the new password again to confirm it.
Once you finish configuring the settings, click on Apply to apply your
configuration.

32
 Figure 4.2.2.2 Popup alert window for Incorrect Username.

4.2.3 IP Configuration
This function allows users to configure the switch’s IP address settings.

DHCP Client: You can select to Enable or Disable DHCP Client function.
When DHCP Client function is enabled, an IP address will be assigned to the
switch from the network’s DHCP server. In this mode, the default IP address
will therefore be replaced by the one assigned by DHCP server. If DHCP Client
is disabled, then the IP address that you specified will be used instead.
IP Address: You can assign the IP address reserved by your network for your
JetNet. If DHCP Client function is enabled, you don’t need to assign an IP
address to the JetNet, as it will be overwritten by DHCP server and shown here.
The default IP is 192.168.10.1.
Subnet Mask: You can assign the subnet mask for the IP address here. If
DHCP Client function is enabled, you don’t need to assign the subnet mask.
The default Subnet Mask is 255.255.255.0. Note: In the CLI, we use the
enabled bit of the subnet mask to represent the number displayed in web UI.
For example, 8 stands for 255.0.0.0; 16 stands for 255.255.0.0; 24 stands for
255.255.255.0.
Default Gateway: You can assign the gateway for the switch here. The default
gateway is 192.168.10.254. Note: In CLI, we use 0.0.0.0/0 to represent for
the default gateway.
Once you finish configuring the settings, click on Apply to apply your
configuration.

33
4.2.4 Time Setting
Time Setting source allow user to set the time manually or through NTP server.
Network Time Protocol (NTP) is used to synchronize computer clocks on the
internet. You can configure NTP settings here to synchronize the clocks of
several switches on the network.
The IEEE1588 PTP (Precision Time Protocol) supports very precise time
synchronization in an Ethernet network. There are two clocks, Master and
Slave. The master device periodically launches an exchange of messages with
slave devices to help each slave clock re-compute the offset between its clock
and the master's clock.
*Note: Please enable one synchronization protocol (PTP/NTP) only.
The JetNet 4508 series also provides Daylight Saving function for some
territories use.

Manual Setting: User can select Manual setting to change time as user wants.
User also can click the button “Get Time from PC” to get PC’s time setting for
switch.
NTP client: Select the Time Setting Source to NTP client can let device enable
the NTP client service. NTP client will be automatically enabled if you change
Time source to NTP Client. The system will send request packet to acquire

34
current time from the NTP server you assigned.

IEEE 1588: select the PTP State to enable this function and select one
operating mode for the precision time synchronizes.
Auto mode: the switch performs PTP Master and slave mode (Bindary mode)
Master mode: switch performs PTP Master only.
Slave mode: switch performs PTP slave only.

Time-zone: Select the time zone where the switch is located. Following table
lists the time zones for different locations for your reference. The default time
zone is GMT Greenwich Mean Time.
Switch(config)# clock timezone
01 (GMT-12:00) Eniwetok, Kwajalein
02 (GMT-11:00) Midway Island, Samoa
03 (GMT-10:00) Hawaii
04 (GMT-09:00) Alaska
05 (GMT-08:00) Pacific Time (US & Canada) , Tijuana
06 (GMT-07:00) Arizona
07 (GMT-07:00) Mountain Time (US & Canada)
08 (GMT-06:00) Central America
09 (GMT-06:00) Central Time (US & Canada)
10 (GMT-06:00) Mexico City
11 (GMT-06:00) Saskatchewan
12 (GMT-05:00) Bogota, Lima, Quito
13 (GMT-05:00) Eastern Time (US & Canada)
14 (GMT-05:00) Indiana (East)
15 (GMT-04:00) Atlantic Time (Canada)
16 (GMT-04:00) Caracas, La Paz
17 (GMT-04:00) Santiago
18 (GMT-03:00) NewFoundland
19 (GMT-03:00) Brasilia
20 (GMT-03:00) Buenos Aires, Georgetown
21 (GMT-03:00) Greenland

35
 22 (GMT-02:00) Mid-Atlantic
23 (GMT-01:00) Azores
24 (GMT-01:00) Cape Verde Is.
25 (GMT) Casablanca, Monrovia
26 (GMT) Greenwich Mean Time: Dublin, Edinburgh, Lisbon, London
27 (GMT+01:00) Amsterdam, Berlin, Bern, Rome, Stockholm, Vienna
28 (GMT+01:00) Belgrade, Bratislava, Budapest, Ljubljana, Prague
29 (GMT+01:00) Brussels, Copenhagen, Madrid, Paris
30 (GMT+01:00) Sarajevo, Skopje, Sofija, Vilnius, Warsaw, Zagreb
31 (GMT+01:00) West Central Africa
32 (GMT+02:00) Athens, Istanbul, Minsk
33 (GMT+02:00) Bucharest
34 (GMT+02:00) Cairo
35 (GMT+02:00) Harare, Pretoria
36 (GMT+02:00) Helsinki, Riga, Tallinn
37 (GMT+02:00) Jerusalem
38 (GMT+03:00) Baghdad
39 (GMT+03:00) Kuwait, Riyadh
40 (GMT+03:00) Moscow, St. Petersburg, Volgograd
41 (GMT+03:00) Nairobi
42 (GMT+03:30) Tehran
43 (GMT+04:00) Abu Dhabi, Muscat
44 (GMT+04:00) Baku, Tbilisi, Yerevan
45 (GMT+04:30) Kabul
46 (GMT+05:00) Ekaterinburg
47 (GMT+05:00) Islamabad, Karachi, Tashkent
48 (GMT+05:30) Calcutta, Chennai, Mumbai, New Delhi
49 (GMT+05:45) Kathmandu
50 (GMT+06:00) Almaty, Novosibirsk
51 (GMT+06:00) Astana, Dhaka
52 (GMT+06:00) Sri Jayawardenepura
53 (GMT+06:30) Rangoon
54 (GMT+07:00) Bangkok, Hanoi, Jakarta
55 (GMT+07:00) Krasnoyarsk
56 (GMT+08:00) Beijing, Chongqing, Hong Kong, Urumqi
57 (GMT+08:00) Irkutsk, Ulaan Bataar
58 (GMT+08:00) Kuala Lumpur, Singapore
59 (GMT+08:00) Perth
60 (GMT+08:00) Taipei
61 (GMT+09:00) Osaka, Sapporo, Tokyo
62 (GMT+09:00) Seoul
63 (GMT+09:00) Yakutsk
64 (GMT+09:30) Adelaide
65 (GMT+09:30) Darwin
66 (GMT+10:00) Brisbane
67 (GMT+10:00) Canberra, Melbourne, Sydney
68 (GMT+10:00) Guam, Port Moresby
69 (GMT+10:00) Hobart
70 (GMT+10:00) Vladivostok
71 (GMT+11:00) Magadan, Solomon Is., New Caledonia
72 (GMT+12:00) Aukland, Wellington
73 (GMT+12:00) Fiji, Kamchatka, Marshall Is.
74 (GMT+13:00) Nuku'alofa

Daylight Saving Time: click the check box to enable the Daylight Saving
Function as the setting of start and end time or disable it.

36
 Daylight Saving Start and Daylight Saving End: the time setting allows user
to selects the week that monthly basis, and sets the End and Start time
individually.

Once you finish those configurations, click on Apply to apply your

configuration.

4.2.5 DHCP Server

You can select to Enable or Disable DHCP Server function. JetNet 4508 /
4508f will assign a new IP address to link partners.

DHCP Server configuration

After selecting to enable DHCP Server function, type in the Network IP address
for the DHCP server IP pool, Subnet Mask, Default Gateway address and
Lease Time for client.

Once you have finished the configuration, click Apply to apply your
configuration
Excluded Address:
You can type a specific address into the IP Address field for the DHCP server
reserved IP address.
The IP address that is listed in the Excluded Address List Table will not be
assigned to the network device. Add or remove an IP address from the
Excluded Address List by clicking Add or Remove.

37
Manual Binding: JetNet 4508 / 4508f provides a MAC address and IP address
binding and removing function. You can type in the specified IP and MAC
address, and then click Add to add a new MAC&IP address binding rule for a
specified link partner, like PLC or any device without DHCP client function. To
remove from the binding list, just select the rule to remove and click Remove.

DHCP Leased Entries: JetNet 4508 / 4508f provides an assigned IP address

list for user check. It will show the MAC and IP address that was assigned by
JetNet 4508 / 4508f. Click the Reload button to refresh the listing.

38
 DHCP Relay Agent
You can select to Enable or Disable DHCP relay agent function, and then
select the modification type of option 82 field.

Relay policy drop: Drops the option 82 field and do not add any option 82
field.
Relay policy keep: Keeps the original option 82 field and forwards to server.
Relay policy replace: Replaces the existing option 82 field and adds new
option 82 field. (This is the default setting)
Helper Address: there are 4 fields for the DHCP server’s IP address. You can
fill the field with preferred IP address of DHCP Server, and then click “Apply” to
activate the DHCP relay agent function. All the DHCP packets from client will
be modified by the policy and forwarded to DHCP server through the gateway
port.

4.2.6 Backup and Restore

With Backup command, you can save current configuration file saved in the
switch’s flash to admin PC or TFTP server. This will allow you to go to Restore
command later to restore the configuration file back to the switch. Before you
restore the configuration file, you must place the backup configuration file in the
PC or TFTP server. The switch will then download this file back to the flash.
There are 2 modes for users to backup/restore the configuration file, Local File
mode and TFTP Server mode.
Local File mode: In this mode, the switch acts as the file server. Users can
browse the target folder and then type the file name to backup the configuration.
Users can also browse the target folder and select existed configuration file to
restore the configuration back to the switch. This mode is only provided by Web
UI while CLI is not supported.
TFTP Server mode: In this mode, the switch acts as TFTP client. Before you do

39
so, make sure that your TFTP server is ready. Then please type the IP address
of TFTP Server and Backup configuration file name. This mode can be used in
both CLI and Web UI.
TFTP Server IP Address: You need to key in the IP address of your TFTP
Server here.
Backup/Restore File Name: Please type the correct file name of the
configuration file..
Configuration File: The configuration file of the switch is a pure text file. You
can open it by word/txt read file. You can also modify the file, add/remove the
configuration settings, and then restore back to the switch.
Startup Configuration File: After you saved the running-config to flash, the
new settings will be kept and work after power cycle. You can use show
startup-config to view it in CLI. The Backup command can only backup such
configuration file to your PC or TFTP server.

Technical Tip:

Default Configuration File: The switch provides the default configuration file in the
system. You can use Reset button, Reload command to reset the system.

Running Configuration File: The switch’s CLI allows you to view the latest settings
running by the system. The information shown here is the settings you set up but
haven’t saved to flash. The settings not yet saved to flash will not work after power
recycle. You can use show running-config to view it in CLI.
Once you finish selecting and configuring the settings, click on Backup or Restore to run

Figure 4.2.6.1 Main UI of Backup & Restore

40
Figure 4.2.6.2 Bacup/Restore Configuration - Local File mode.

Click on Folder icon to select the target file you want to backup/restore.
Note that the folders of the path to the target file do not allow you to input space
key.

Figure 4.2.6.3 Backup/Restore Configuration - TFTP Server mode

Type the IP address of TFTP Server IP. Then click on Backup/Restore.

Note: point to the wrong file will cause the entire configuration missed

41
4.2.7 Firmware Upgrade
In this section, you can update the latest firmware for your switch. Korenix
provides the latest firmware in Korenix Web site. The new firmware may include
new features, bug fixes or other software changes. We’ll also provide the
release notes for the update as well. For technical viewpoint, we suggest you
use the latest firmware before installing the switch to the customer site.
Note: the system will automatically reboot after you finished upgrading
new firmware. Please remind the attached users before you do that.
Figure 4.2.7.1 Main UI of Firmware Upgrade

Sample of JetNet 5010G firmware upgrade

There are 2 modes for users to backup/restore the configuration file, Local File
mode and TFTP Server mode.
Local File mode: In this mode, the switch acts as the file server. Users can
browse the target folder and then type the file name to backup the configuration.
Users also can browse the target folder and select the existed configuration file
to restore the configuration back to the switch. This mode is only provided by
Web UI while CLI is not supported.
TFTP Server mode: In this mode, the switch acts as the TFTP client. Before
you do so, make sure that your TFTP server is ready. And then please type the
IP address of TFTP Server IP address. This mode can be used in both CLI and
Web UI.
TFTP Server IP Address: You need to key in the IP address of your TFTP
Server here.

42
Firmware File Name: The file name of the new firmware.
The UI also shows you the current firmware version and built date of current
firmware. Please check the version number after the switch is rebooted.

Figure 4.2.7.2 Firmware Upgrade - Local File mode.

Click on Folder icon to select the target firmware file you want to upgrade.

Figure 4.2.7.3 Firmware Upgrade – TFTP Server mode.

Type the IP address of TFTP Server and Firmware File Name. Then click on
Upgrade to start the process.
After finishing transmitting the firmware, the system will copy the firmware file
and replace the firmware in the flash. The CLI show …… until the process is
finished.

43
4.2.8 Factory Default
In this section, you can reset all the configurations of the switch to default
setting. Click on Reset the system will then reset all configurations to default
setting. The system will show you pop-up message window after finishing this
command. Default setting will work after rebooting the switch.

Figure- 4.2.8.1 The main screen of the Reset to Default

Figure 4.2.8.2 Popup alert screen to confirm the command. Click on Yes to
start it.

Figure 4.2.8.3 Popup message screen to show you that have done the
command. Click on OK to close the screen. Then please go to Reboot page to
reboot the switch.

Click on OK. The system will then auto reboot the device.
Note: If you already configured the IP of your device to other IP address, when
you use this command by CLI and Web UI, our software will not reset the IP
address to default IP. The system will remain the IP address so that you can still
connect the switch via the network.

44
4.2.9 System Reboot
System Reboot allows you to reboot the device. Some of the feature changes
require you to reboot the system. Click on Reboot to reboot your device.
Note: Remember to click on Save button to save your settings. Otherwise, the
settings you made will be gone when the switch is powered off.
Figure 4.2.9.1 Main screen for Rebooting

Figure 4.2.9.2 Pop-up alert screen to request confirmation. Click on Yes.

Then the switch will be rebooted immediately.

Figure 4.2.9.3 Pop-up message screen appears when rebooting the switch.

45
4.2.10 CLI Commands for Basic Setting

Feature Command Line

Switch Setting
System Name Switch(config)# hostname
WORD Network name of this system
Switch(config)# hostname JN4508
SWITCH(config)#
System Location SWITCH(config)# snmp-server location Taipei

System Contact SWITCH(config)# snmp-server contact [email protected]

Display SWITCH# show snmp-server name

SWITCH#

SWITCH# show snmp-server location

Taipei

SWITCH# show snmp-server contact

[email protected]

SWITCH> show version

0.31-20061218

Switch# show hardware mac

MAC Address : 00:12:77:FF:01:B0
Admin Password
User Name and SWITCH(config)# administrator
NAME Administrator account name
Password SWITCH(config)# administrator orwell
PASSWORD Administrator account password
SWITCH(config)# administrator orwell orwell
Change administrator account orwell and password orwell
success.
Display SWITCH# show administrator
Administrator account information
name: orwell
password: orwell
IP Configuration
IP Address/Mask SWITCH(config)# int vlan 1
(192.168.10.8, SWITCH(config-if)# ip
255.255.255.0 address
dhcp
SWITCH(config-if)# ip address 192.168.10.8/24
SWITCH(config-if)# ip dhcp client
SWITCH(config-if)# ip dhcp client renew
Gateway SWITCH(config)# ip route 0.0.0.0/0 192.168.10.254/24
Remove Gateway SWITCH(config)# no ip route 0.0.0.0/0 192.168.10.254/24
Display SWITCH# show running-config
………
!
interface vlan1
ip address 192.168.10.8/24
no shutdown

46
 !
ip route 0.0.0.0/0 192.168.10.254/24
!
Time Setting
NTP Server SWITCH(config)# ntp peer
enable
disable
primary
secondary
SWITCH(config)# ntp peer primary
IPADDR
SWITCH(config)# ntp peer primary 192.168.10.120
Time Zone SWITCH(config)# clock timezone 26
Sun Jan 1 04:13:24 2006 (GMT) Greenwich Mean Time:
Dublin, Edinburgh, Lisbon, London

Note: By typing clock timezone ?, you can see the timezone

list. Then choose the number of the timezone you want to
select.
IEEE 1588 PTP Switch (config) # ptpd run Æ enable IEEE 1588 PTP with auto
mode
PTPd is enabled!
Switch (config)# ptpd run preferred-clock Æ master mode
Switch (config)# ptpd run slave Æ slave mode
Switch (config)# no ptpd run Æ disable IEEE 1588 PTP
PTPd is disabled!

Display SWITCH# sh ntp associations

Network time protocol
Status : Disabled
Primary peer : N/A
Secondary peer : N/A
SWITCH# show clock
Sun Jan 1 04:14:19 2006 (GMT) Greenwich Mean Time:
Dublin, Edinburgh, Lisbon, London

SWITCH# show clock timezone

clock timezone (26) (GMT) Greenwich Mean Time: Dublin,
Edinburgh, Lisbon, London

Daylight Saving Switch(config)# clock summer-time 4 0 2 12:00 4 0 3 12:00

Clock summer-time <start week of month > <start weekday>
<start month> <start Hour:Min> <end week of month> <end
weekday> <end month> <end Hour:Min>
DHCP Server
DHCP Server Enable DHCP Server on JetNet Switch
Switch#
configuration Switch# configure terminal
Switch(config)# router dhcp
Switch(config-dhcp)# service dhcp

Configure DHCP network address pool

Switch(config-dhcp)#network 50.50.50.0/4 -( network/mask)
Switch(config-dhcp)#default-router 50.50.50.1
Lease time configure Switch(config-dhcp)#lease 300 (300 sec)

47
DHCP Relay Agent Enable DHCP Relay Agent
Switch#
Switch# configure terminal
Switch(config)# router dhcp
Switch(config-dhcp)# service dhcp
Switch(config-dhcp)# ip dhcp relay information option

Enable DHCP Relay policy

Switch(config-dhcp)# ip dhcp relay information policy replace
drop Relay Policy
keep Drop/Keep/Replace option82 field
replace
Show DHCP server Switch# show ip dhcp server statistics
Switch# show ip dhcp server statistics
information DHCP Server ON
Address Pool 1
network:192.168.17.0/24
default-router:192.168.17.254
lease time:300
Excluded Address List
IP Address
---------------
(list excluded address)
Manual Binding List
IP Address MAC Address
--------------- --------------
(list IP & MAC binding entry)
Leased Address List
IP Address MAC Address Leased Time Remains
--------------- -------------- --------------------
(list leased Time remain information for each entry)
Backup and Restore
Backup Startup Switch# copy startup-config tftp: 192.168.10.33/default.conf
Writing Configuration [OK]
Configuration file
Note 1: To backup the latest startup configuration file, you
should save current settings to flash first. You can refer to 4.12
to see how to save settings to the flash.
Note 2: 192.168.10.33 is the TFTP server’s IP and default.conf
is name of the configuration file. Your environment may use
different IP addresses or different file name. Please type target
TFTP server IP or file name in this command.
Restore Configuration Switch# copy tftp: 192.168.10.33/default.conf startup-config
Show Startup Switch# show startup-config
Configuration
Show Running Switch# show running-config
Configuration
Firmware Upgrade
Firmware Upgrade Switch# archive download-sw /overwrite tftp 192.168.10.33
JN4508.bin
Firmware upgrading, don't turn off the switch!
Tftping file JN4508.bin
Firmware upgrading
................................................................................
................................................................................
...........................

48
 Firmware upgrade success!!
Rebooting.......
Factory Default
Factory Default Switch# reload default-config file
Reload OK!
Switch# reboot
System Reboot
Reboot Switch# reboot

49
4.3 Port Configuration
Port Configuration group enables you to enable/disable port state, or
configure port auto-negotiation, speed, and duplex, flow control, rate limit
control and port aggregation settings. It also allows you to view port status
and aggregation information.

Following commands are included in this group:

4.3.1 Port Control
4.3.2 Port Status
4.3.3 Rate Control
4.3.4 Port Trunking
4.3.5 Command Lines for Port Configuration

4.3.1 Port Control

Port Control commands allow you to enable/disable port state, or configure
the port auto-negotiation, speed, duplex and flow control.

Select the port you want to configure and make changes to the port.
In State column, you can enable or disable the state of this port. Once you
disable, the port stop to link to the other end and stop to forward any traffic.
The default setting is Enable which means all the ports are workable when
you receive the device.

50
In Speed/Duplex column, you can configure port speed and duplex mode
of this port. Below are the selections you can choose:
JetNet 4508 (fa1~fa6)/ JetNet 4508f (fa1~fa6): Auto Negotiation, 10Half
(10Mbps Half Duplex mode), 10 Full (10Mbps, Full Duplex mode), 100 Half
(100Mbps, Half Duplex), 100 Full (100Mbps, Full Duplex mode)
JetNet 4508 (fa7~fa8): 100Mbps Auto Negotiation, 100 Full (100Mbps, Full
Duplex mode), 100 Half (100Mnps, Half Duplex)
JetNet 4508f (fa7, fa8): 100Full (100Mbps, Full Duplex) only.
In Flow Control column, “Symmetric” means that you need to activate the
flow control function of the remote network device in order to let the flow
control of that corresponding port on the switch to work. “Disable” means
that you don’t need to activate the flow control function of the remote
network device, as the flow control of that corresponding port on the switch
will work anyway.
Once you finish configuring the settings, click on Apply to save the
configuration.

Technical Tips: If both ends are not at the same speed, they can’t link with
each other. If both ends are not in the same duplex mode, they will be
connected by half mode.

51
4.3.2 Port Status

The Port Status shows the current port you current port status. It includes
connection type, port link status, exactly operating speed and duplex mode
and the flow control setting.

The description of the columns is as below:

Port: Port interface number.
Type: 100TX -> Fast Ethernet port.
Link: Link status. Up -> Link UP. Down -> Link Down.
State: Enable -> State is enabled. Disable -> The port is disable/shutdown.
Speed/Duplex: Current working status of the port.
Flow Control: The state of the flow control.

52
4.3.3 Rate Control
The Rate Control feature allows user to limit the each port’s data rate; the
limitation mechanism is based on specified packet type. With the Ingress /
Egress rate control feature, the network performance can be improved.

Rate Control is a form of flow control used to enforce a strict bandwidth limit
at a port. You can program separate transmit (Egress Rule) and receive
(Ingress Rule) rate limits at each port, and even apply the limit to certain
packet types as described below.

Packet type: You can select the packet type that you want to filter. The
packet types of the Ingress Rule listed here include Broadcast Only /
Broadcast and multicast / Broadcast, Multicast and Unknown Unicast
or All. The packet types of the Egress Rule (outgoing) only support all
packet types.
Rate: This column allows you to manually assign the limit rate of the port.
Valid values are from 1Mbps-100Mbps for fast Ethernet ports. The step of
the rate is 1 Mbps. Default value of Ingress Rule is “8” Mbps; default value
of Egress Rule is 0 Mbps. 0 stands for disabling the rate control for the port.
Click on Apply to apply the configuration.

53
4.3.4 Port Trunking
Port Trunking configuration allows you to group multiple Ethernet ports in
parallel to increase link bandwidth. The aggregated ports can be viewed as
one physical port so that the bandwidth is higher than merely one single
Ethernet port. The member ports of the same trunk group can balance the
loading and backup for each other. Port Trunking feature is usually used
when you need higher bandwidth for backbone network. This is an
inexpensive way for you to transfer more data.

There are some different descriptions for the port trunking. Different
manufacturers may use different descriptions for their products, like Link
Aggregation Group (LAG), Link Aggregation Control Protocol, Ethernet
Trunk, Ether Channel…etc. Most of the implementations now conform to
IEEE standard, 802.3ad.
The aggregated ports can interconnect to the other switch which also
supports Port Trunking. Korenix Supports 2 types of port trunking. One is
Static Trunk, the other is 802.3ad. When the other end uses 802.3ad LACP,
you should assign 802.3ad LACP to the trunk. When the other end uses
non-802.3ad, you can then use Static Trunk.
There are 2 configuration pages, Aggregation Setting and Aggregation
Status.

54
Aggregation Setting

Trunk Size: The switch can support up to 4 trunk groups and maximum
trunk member up to 8 ports.
Group ID: Group ID is the ID for the port trunking group. Ports with same
group ID are in the same group.
Trunk Type: Static and 802.3ad LACP. Each Trunk Group can only
support Static or 802.3ad LACP. Choose the type you need here.

55
Aggregation Status
This page shows the status of port aggregation. Once the aggregation ports
are negotiated well, you will see following status.

Group ID: Display Trunk 1 to Trunk 8 set up in Aggregation Setting.

Type: Static or LACP set up in Aggregation Setting. (The JetNet 4508 series
only support 4 trunk groups.)
Aggregated Ports: When LACP links well, you can see the member ports
in aggregated column.
Individual Ports: When LACP is enabled, member ports of LACP group
which are not connected to correct LACP member ports will be displayed in
the Individual column.
Link Down ports: When LACP is enabled, member ports of LACP group
which are not linked up will be displayed in the Link Down column.

56
4.3.5 Command Lines for Port Configuration

Feature Command Line

Port Control
Port Control – State Switch(config-if)# shutdown -> Disable port state
Port1 Link Change to DOWN
interface fastethernet1 is shutdown now.

Switch(config-if)# no shutdown -> Enable port state

Port1 Link Change to DOWN
Port1 Link Change to UP
interface fastethernet1 is up now.
Switch(config-if)# Port1 Link Change to UP

Port Control – Auto Switch(config)# interface fa1

Negotiation Switch(config-if)# auto-negotiation
Auto-negotiation of port 1 is enabled!

Port Control – Force Switch(config-if)# speed 100

Speed/Duplex Port1 Link Change to DOWN
set the speed mode ok!
Switch(config-if)# Port1 Link Change to UP

Switch(config-if)# duplex full

Port1 Link Change to DOWN
set the duplex mode ok!
Switch(config-if)# Port1 Link Change to UP

Port Control – Flow Switch(config-if)# flowcontrol on

Control Flowcontrol on for port 1 set ok!

Switch(config-if)# flowcontrol off

Flowcontrol off for port 1 set ok!

Port Status
Port Status Switch# show interface fa1
Interface fastethernet1
Administrative Status : Enable
Operating Status : Connected
Duplex : Full
Speed : 100
Flow Control :off
Default Port VLAN ID: 1
Ingress Filtering : Disabled
Acceptable Frame Type : All
Port Security : Disabled
Auto Negotiation : Disable
Loopback Mode : None
STP Status: forwarding
Default CoS Value for untagged packets is 0.
Mdix mode is Disable.
Medium mode is Copper.

57
 Note: Administrative Status -> Port state of the port. Operating
status -> Current status of the port. Duplex -> Duplex mode of
the port. Speed -> Speed mode of the port. Flow control ->
Flow Control status of the port.

Rate Control
Rate Control – Switch(config-if)# rate-limit
egress Outgoing packets
Ingress or Egress ingress Incoming packets

Note: To enable rate control, you should select the Ingress or

Egress rule first; then assign the packet type and bandwidth.
Rate Control – Filter Switch(config-if)# rate-limit ingress mode
all Limit all frames
Packet Type broadcast Limit Broadcast frames
flooded-unicast Limit Broadcast, Multicast and flooded unicast frames
multicast Limit Broadcast and Multicast frames
Switch(config-if)# rate-limit ingress mode broadcast
Set the ingress limit mode broadcast ok.
Rate Control - Switch(config-if)# rate-limit ingress bandwidth
<0-100> Limit in magabits per second (0 is no limit)
Bandwidth Switch(config-if)# rate-limit ingress bandwidth 8
Set the ingress rate limit 8Mbps for Port 1.
Port Trunking
LACP Switch(config)# lacp group 1 fa6-8
Group 1 based on LACP(802.3ad) is enabled!

Note: The interface list is fa1-8

Note: different speed port can’t be aggregated together.
Static Trunk Switch(config)# trunk group 2 fa4-5
Trunk group 2 enable ok!
Display - LACP Swhitch# show lacp internal
LACP group 1 internal information:
LACP Port Admin Oper Port
Port Priority Key Key State
----- ----------- -------- -------- -------
6 1 6 6 0x45
7 1 7 7 0x45
8 1 8 8 0x45

LACP group 2 is inactive

LACP group 3 is inactive
LACP group 4 is inactive
Display - Trunk Switch# show trunk group 1
FLAGS: I -> Individual P -> In channel
D -> Port Down

Trunk Group
GroupID Protocol Ports
--------+---------+------------------------------------
1 LACP 6(D) 7(D) 8(D)
Switch# show trunk group 2
FLAGS: I -> Individual P -> In channel
D -> Port Down

58
Trunk Group
GroupID Protocol Ports
--------+---------+------------------------------------
2 Static 4(D) 5(P)
Switch#

59
4.4 Network Redundancy
It is critical for industrial applications that network remains non-stop. JetNet
4508 / 4508f firmware supports standard RSTP, Multiple Super Ring, Rapid
Dual Homing and backward compatible with Legacy Super Ring Client
modes.
Multiple Super Ring (MSRTM) technology is Korenix’s 3rd generation Ring
redundancy technology. This is patented and protected by Korenix and is
used in countries all over the world. MSR ranks the fastest restore and
failover time in the world, 0 ms for restore and about 5 milliseconds for
failover for copper.
Advanced Rapid Dual Homing (RDHTM) technology also facilitates JetNet
managed Switch to connect with a core managed switch easily and
conveniently. With RDHTM technology, you can also couple several Rapid
Super Rings or RSTP cloud together, which is also known as Auto Ring
Coupling.
To become backwards compatible with the Legacy Super Ring technology
implemented in the JetNet series, JetNet 4508 / 4508f also supports Super
Ring Client mode. The Super Ring ports can pass through Super Ring
control packets extremely well and works with Super Ring.
Besides Korenix ring technology, JetNet 4508 / 4508f also supports
802.1D-2004 version Rapid Spanning Tree Protocol (RSTP). New version
of RSTP standard includes 802.1D-1998 STP, 802.1w RSTP, IEEE 802.1s
MSTP (Multiple Spanning Tree). The MSTP function is available from 1.1
version firmwear, if your device does not support it, please download the
new firmware from Korenix Web site.
Following commands are included in this group:
4.4.1 STP Configuration
4.4.2 Port Configuration
4.4.3 STP Information
4.4.4 MSTP Configuration
4.4.5 MSTP Port Configuration
4.4.6 MSTP Information
4.4.7 Multiple Super Ring
4.4.8 Multiple Super Ring Information
4.4.9 Command lines for network redundancy

4.4.1 STP Configuration

This page allows select the STP mode and configuring the global
STP/RSTP Bridge Configuraiton.

60
The STP mode includes the STP, RSTP, MSTP and Disable. Please select
the STP mode for your system first. The default mode is RSTP enabled.
Afte select the STP or RSTP mode; continue to configure the gloable
Bridge parameters for STP and RSTP.
After select the MSTP mode, please go to MSTP Configuration page.

RSTP (Refer to the 4.4.1 of previous version manual.)

RSTP is the abbreviation of Rapid Spanning Tree Protocol. If a switch has
more than one path to a destination, it will lead to message loops that can
generate broadcast storms and quickly bog down a network. The spanning
tree was created to combat the negative effects of message loops in
switched networks. A spanning tree uses a spanning tree algorithm (STA)
to automatically sense whether a switch has more than one way to
communicate with a node. It will then select the best path (primary), and
block the other path(s). It will also keep track of the blocked path(s) in case
the primary path fails. Spanning Tree Protocol (STP) introduced a standard
method to accomplish this. It is specified in IEEE 802.1D-1998. Later,
Rapid Spanning Tree Protocol (RSTP) was adopted and represents the
evolution of STP, providing much faster spanning tree convergence after a
topology change. This is specified in IEEE 802.1w. In 2004, 802.1w is
included into 802.1D-2004 version. This switch supports both RSTP and
STP (all switches that support RSTP are also backward compatible with
switches that support only STP).

Bridge Configuration
Bridge Address: This shows the switch’s MAC address.
Priority (0-61440): RSTP uses bridge ID to determine the root bridge, the
bridge with the highest bridge ID becomes the root bridge. The bridge ID is
composed of bridge priority and bridge MAC address. So that the bridge

61
 with the highest priority becomes the highest bridge ID. If all the bridge ID
has the same priority, the bridge with the lowest MAC address will then
become the root bridge.
Note: The bridge priority value must be in multiples of 4096. A device with a
lower number has a higher bridge priority. Ex: 4096 is higher than 32768.
Note: The Web GUI allows user select the priority number directly. This is
the convinent of the GUI design. When you configure the value through the
CLI or SNMP, you may need to type the value directly. Please follow the n x
4096 ruls for the Bridge Priority.
Max Age (6-40): Enter a value from 6 to 40 seconds here. This value
represents the time that a bridge will wait without receiving Spanning Tree
Protocol configuration messages before attempting to reconfigure.
If JetNet is not the root bridge, and if it has not received a hello message
from the root bridge in an amount of time equal to Max Age, then JetNet will
reconfigure itself as a root bridge. Once two or more devices on the
network are recognized as a root bridge, the devices will renegotiate to set
up a new spanning tree topology.
Hello Time (1-10): Enter a value from 1 to 10 seconds here. This is a
periodic timer that drives the switch to send out BPDU (Bridge Protocol
Data Unit) packet to check current STP status.
The root bridge of the spanning tree topology periodically sends out a
“hello” message to other devices on the network to check if the topology is
“healthy”. The “hello time” is the amount of time the root has waited during
sending hello messages.
Forward Delay Time (4-30): Enter a value between 4 and 30 seconds.
This value is the time that a port waits before changing from Spanning Tree
Protocol learning and listening states to forwarding state.
This is the amount of time JetNet will wait before checking to see if it should
be changed to a different state.
Once you have completed your configuration, click on Apply to apply your
settings.
Note: You must observe the following rule to configure Hello Time,
Forwarding Delay, and Max Age parameters.
2 × (Forward Delay Time – 1 sec) ≥ Max Age Time ≥ 2 × (Hello Time
value + 1 sec)

4.4.2 STP Port Configuration

This page allows you to configure the port parameter after enabled STP or
RSTP.
Port Configuration
Select the port you want to configure and you will be able to view current

62
setting and status of the port.

Path Cost: Enter a number between 1 and 200,000,000. This value

represents the “cost” of the path to the other bridge from the transmitting
bridge at the specified port.
Priority: Enter a value between 0 and 240, using multiples of 16. This is the
value that decides which port should be blocked by priority in a LAN.
Link Type: There are 3 types for you select. Auto, P2P and Share.
Some of the rapid state transitions that are possible within RSTP depend
upon whether the port of concern can only be connected to another bridge
(i.e. it is served by a point-to-point LAN segment), or if it can be connected
to two or more bridges (i.e. it is served by a shared-medium LAN segment).
This function allows link status of the link to be manipulated administratively.
“Auto” means to auto select P2P or Share mode. “P2P” means P2P is
enabled, the 2 ends work in Full duplex mode. While “Share” is enabled, it
means P2P is disabled, the 2 ends may connect through a share media
and work in Half duplex mode.
Edge: A port directly connected to the end stations cannot create a bridging
loop in the network. To configure this port as an edge port, set the port to
the Enable state. When the non-bridge device connects an admin edge
port, this port will be in blocking state and turn to forwarding state in 4
seconds.
Once you finish your configuration, click on Apply to save your settings.

63
4.4.3 RSTP Info

This page allows you to see the information of the root switch and port
status.

Root Information: You can see root Bridge ID, Root Priority, Root Port,
Root Path Cost and the Max Age, Hello Time and Forward Delay of BPDU
sent from the root switch.
Port Information: You can see port Role, Port State, Path Cost, Port
Priority, Oper P2P mode, Oper edge port mode and Aggregated (ID/Type).

4.4.4 MSTP (Multiple Spanning Tree Protocol) Configuration

MSTP is the abbreviation of Multiple Spanning Tree Protocol. This protocol

is a direct extension of RSTP. It can provide an independent spanning tree
for different VLANs. It simplifies network management, provides for even
faster convergence than RSTP by limiting the size of each region, and
prevents VLAN members from being segmented from the rest of the group
(as sometimes occurs with IEEE 802.1D STP).

While using MSTP, there are some new concepts of network architecture.
A switch may belong to different group, acts as root or designate switch,
generate BPDU for the network to maintain the forwarding table of the
spanning tree. With MSTP, it can also provide multiple forwarding paths
and enable load balancing. Understand the architecture allows you to

64
maintain the correct spanning tree and operate effectively.

One VLAN can be mapped to a Multiple Spanning Tree Instance (MSTI).

The maximum Instance of JetNet 4508 supports is 16, range from 0-15.
The MSTP builds a separate Multiple Spanning Tree (MST) for each
instance to maintain connectivity among each of the assigned VLAN
groups. An Internal Spanning Tree (IST) is used to connect all the MSTP
switches within an MST region. An MST Region may contain multiple
MSTP Instances.

The figure shows there are 2 VLANs/MSTP Instances and each instance
has its Root and forwarding paths.

A Common Spanning Tree (CST) interconnects all adjuacent MST regions

and acts as a virtual bridge node for communications with STP or RSTP
nodes in the global network. MSTP connects all bridges and LAN segments
with a single Common and Internal Spanning Tree (CIST). The CIST is
formed as a result of the running spanning tree algorithm between switches
that support the STP, RSTP, MSTP protocols.

The figure shows the CST large network. In this network, a Region may

65
have different instances and its own forwarding path and table; however, it
acts as a single Brige of CST.

To configure the MSTP setting, the STP Mode of the STP Configuration
page should be changed to MSTP mode first.

After enabled MSTP mode, then you can go to the MSTP Configuraiton
pages.

MSTP Region Configuration

This page allows configure the Region Name and its Revision, mapping the
VLAN to Instance and check current MST Instance configuration. The
network can be divided virtually to different Regions. The switches within
the Region should have the same Region and Revision leve.
Region Name: The name for the Region. Maximum length: 32 characters.
Revision: The revision for the Region. Range: 0-65535; Default: 0)
Once you finish your configuration, click on Apply to apply your settings.

New MST Instance

This page allows mapping the VLAN to Instance and assign priority to the
instance. Before mapping VLAN to Instance, you should create VLAN and
assign the member ports first. Please refer to the VLAN setting page.

66
 Instance ID: Select the Instance ID, the available number is 1-15.
VLAN Group: Type the VLAN ID you want mapping to the instance.
Instance Priority: Assign the priority to the instance.
After finish your configuration, click on Add to apply your settings.

Current MST Instance Configuration

This page allows you to see the current MST Instance Configuration you
added. Click on “Apply” to apply the setting. You can “Remove” the
instance or “Reload“ the configuration display in this page.

4.4.5 MSTP Port Configuration

This page allows configure the Port settings. Choose the Instance ID you
want to configure. The MSTP enabled and linked up ports within the
instance will be listed in this table.
Note that the ports not belonged to the Instance, or the ports not MSTP
activated will not display. The meaning of the Path Cost, Priority, Link Type
and Edge Port is the same as the definition of RSTP.

67
 Path Cost: Enter a number between 1 and 200,000,000. This value
represents the “cost” of the path to the other bridge from the transmitting
bridge at the specified port.
Priority: Enter a value between 0 and 240, using multiples of 16. This is the
value that decides which port should be blocked by priority in a LAN.
Link Type: There are 3 types for you select. Auto, P2P and Share.
Some of the rapid state transitions that are possible within RSTP depend
upon whether the port of concern can only be connected to another bridge
(i.e. it is served by a point-to-point LAN segment), or if it can be connected
to two or more bridges (i.e. it is served by a shared-medium LAN segment).
This function allows link status of the link to be manipulated administratively.
“Auto” means to auto select P2P or Share mode. “P2P” means P2P is
enabled; the 2 ends work in full duplex mode. While “Share” is enabled, it
means P2P is disabled; the 2 ends may connect through a share media
and work in half duplex mode.
Edge: A port directly connected to the end stations cannot create a bridging
loop in the network. To configure this port as an edge port, set the port to
the Enable state. When the non-bridge device connects an admin edge
port, this port will be in blocking state and turn to forwarding state in 4
seconds.
Once you finish your configuration, click on Apply to save your settings.

4.4.6 MSTP Information

This page allows you to see the current MSTP information.

68
Choose the Instance ID first. If the instance is not added, the information
remains blank.
The Root Information shows the setting of the Root switch.
The Port Information shows the port setting and status of the ports within
the instance.

Click “Reload“ to reload the MSTP information display.

69
4.4.7 Multiple Super Ring (MSR) (The same as 4.4.31 of previous version
manual.)
The most common industrial network redundancy is to form a ring or loop.
Typically, the managed switches are connected in series and the last switch is
connected back to the first one. In such connection, you can implement Korenix
Multiple Super Ring technology to get fatest recovery performance.
Multiple Super Ring (MSR) technology is Korenix’s 3rd generation Ring
redundancy technology. This is patented and protected by Korenix and is used in
countries all over the world. MSR ranks the fastest restore and failover time in the
world, 0 ms for restore and about milliseconds level for failover for 100Base-TX
copper port. The other interface may take longer time due to the media
characteristics.
Advanced Rapid Dual Homing (RDH) technology also facilitates JetNet
Managed Switch to connect with a core managed switch easily and conveniently.
With RDH technology, you can also couple several Rapid Super Rings or RSTP
cloud together, which is also known as Auto Ring Coupling.
TrunkRing technology allows integrate MSR with LACP/Port Trunking. The
LACP/Trunk aggregated ports is a virtual interface and it can work as the Ring
port of the MSR.
MultiRing is an outstanding technology Korenix can support. Multiple rings can
be aggregated within one switch by using different Ring ID. The maximum Ring
number one switch can support is half of total port volume. For example, the
JetNet 4508 / 4508f is an 8 port Fast Ethernet Switch design, which means
maximum 4 Rings (4 100Mbps Rings) can be aggregated in one JetNet 4508 /
4508f. The feature saves much effort when constructing complex network
architecture.
To become backwards compatible with the Legacy Super Ring technology
implemented in JetNet 4008/4508 V1 series switches, JetNet 4510/4518/5000
Series also supports Super Ring Client mode. The Super Ring ports can pass
through Super Ring control packets extremely well and works with Super Ring.
New Ring: To create a Rapdis Super Ring. Jjust fill in the Ring ID which has
range from 0 to 31. If the name field is left blank, the name of this ring will be
automatically naming with Ring ID.

70
Ring Configuration
ID: Once a Ring is created, This appears and can not be changed.
Name: This field will show the name of the Ring. If it is not filled in when creating,
it will be automatically named by the rule “RingID”.
Version: The version of Ring can be changed here. There are three modes to
choose: Rapid Super Ring as default; Super ring for compatible with Korenix 1st
general ring and Any Ring for compatible with other version of rings.
Device Priority: The switch with highest priority (highest value) will be
automatically selected as Ring Master. Then one of the ring ports in this switch
will become forwarding port and the other one will become blocking port. If all of
the switches have the same priority, the switch with the biggest MAC address will
be selected as Ring Master.
Ring Port1: In Rapid Super Ring environment, you should have 2 Ring Ports. No
matter this switch is Ring Master or not, when configuring RSR, 2 ports should be
selected to be Ring Ports. For Ring Master, one of the ring ports will become the
forwarding port and the other one will become the blocking port.
Path Cost: Change the Path Cost of Ring Port1. If this switch is the Ring Master
of a Ring, then it determines the blocking port. The Port with higher Path Cost in
the two ring ports will become the blocking port, If the Path Cost is the same, the
port with larger port number will become the blocking port.
Ring Port2: Assign another port for ring connection
Path Cost: Change the Path Cost of Ring Port2
Rapid Dual Homing: Rapid Dual Homing is an important feature of Korenix 3rd
generation Ring redundancy technology. When you want to connect multiple
RSR or form redundant topology with other vendors,RDH could allow you to have
maximum 7 multiple links for redundancy without any problem.
In Dual Homing I released with JetNet 4000/4500 series, you have to configure
additional port as Dual Homing port to two uplink switches. In Rapid Dual Homing,
you don’t need to configure specific port to connect to other protocol. The Rapid

71
Dual Homing will smartly choose the fastest link for primary link and block all the
other link to avoid loop. If the primary link failed, Rapid Dual Homing will
automatically forward the secondary link for network redundant. Of course, if
there are more connections, they will be standby links and recover one of then if
both primary and secondary links are broken.
Ring status: To enable/disable the Ring. Please remember to enable the ring
after you add it.
MultiRing: The MultiRing technology is one of the patterns of the MSR
technology; it allows you to aggregate multiple rings within one switch. Create
multiple ring ID and assign different ring port 1 and port 2 to each ring, thus the
switch can have multiple rings in one JetNet Switch.
When implementing MultiRing, remember that the different rings can NOT use
the same ring ID. The other settings are the same as above description.
Technically, the maximum ring volume the MultiRing supported is up to 16 rings.
Due the limited number of ports, the number of ring network is the half of port
number.
TrunkRing: The MultiRing technology is part of the MSR technology which
combines the MSR with the port trunking technology. After multiple ports
aggregated, this is so-call port trunking (Staticly or learnt by LACP protocol), the
Trunk ID can be one of the port ID of the MSR technology. Configured the port
trunking first then you can add the Trunk group as a Ring Port in managed
switch.

72
4.4.8 Ring Info (The same as 4.4.4 of previous version manual.)
This page shows the RSR information.

ID: Ring ID.

Version: which version of this ring, this field could be Rapid Super Ring, Super
Ring, or Any Ring
Role: This Switch is RM or nonRM
Status: If this field is Normal which means the redundancy is approved. If any
one of the link in this Ring is broken, then the status will be Abnormal.
RM MAC: The MAC address of Ring Master of this Ring. It helps to find the
redundant path.
Blocking Port: This field shows which is blocked port of RM.

Role Transition Count: This means how many times this switch has changed its
Role from nonRM to RM or from RM to nonRM.
Role state Transition Count: This number means how many times the Ring
status has been transformed between Normal and Abnormal state.

4.4.9 Command Lines:

Feature Command Line

Global (STP, RSTP, MSTP)
Enable Switch(config)# spanning-tree enable

73
Disable Switch (config)# spanning-tree disable
Mode (Choose the Switch(config)# spanning-tree mode
Spanning Tree mode) rst the rapid spanning-tree protocol (802.1w)
stp the spanning-tree prtotcol (802.1d)
mst the multiple spanning-tree protocol (802.1s)
Bridge Priority Switch(config)# spanning-tree priority
<0-61440> valid range is 0 to 61440 in multiple of 4096
Switch(config)# spanning-tree priority 4096
Bridge Times Switch(config)# spanning-tree bridge-times (forward Delay)
(max-age) (Hello Time)
Switch(config)# spanning-tree bridge-times 15 20 2

This command allows you configure all the timing in one time.
Forward Delay Switch(config)# spanning-tree forward-time
<4-30> Valid range is 4~30 seconds
Switch(config)# spanning-tree forward-time 15
Max Age Switch(config)# spanning-tree max-age
<6-40> Valid range is 6~40 seconds
Switch(config)# spanning-tree max-age 20
Hello Time Switch(config)# spanning-tree hello-time
<1-10> Valid range is 1~10 seconds
Switch(config)# spanning-tree hello-time 2
MSTP
Enter the MSTP Switch(config)# spanning-tree mst
Configuration Tree MSTMAP the mst instance number or range
configuration enter mst configuration mode
forward-time the forward dleay time
hello-time the hello time
max-age the message maximum age time
max-hops the maximum hops
sync sync port state of exist vlan entry
Switch(config)# spanning-tree mst configuration
Switch(config)# spanning-tree mst configuration
Switch(config-mst)#
abort exit current mode and discard all changes
end exit current mode, change to enable mode and apply all
changes
exit exit current mode and apply all changes
instance the mst instance
list Print command list
name the name of mst region
no Negate a command or set its defaults
quit exit current mode and apply all changes
revision the revision of mst region
show show mst configuration
Region Configuration Region Name:
Switch(config-mst)# name
NAME the name string
Switch(config-mst)# name korenix
Region Revision:
Switch(config-mst)# revision
<0-65535> the value of revision
Switch(config-mst)# revision 65535
Mapping Instance to Switch(config-mst)# instance
VLAN (Ex: Mapping <1-15> target instance number
VLAN 2 to Instance 1) Switch(config-mst)# instance 1 vlan
VLANMAP target vlan number(ex.10) or range(ex.1-10)

74
 Switch(config-mst)# instance 1 vlan 2
Display Current MST Switch(config-mst)# show current
Configuraion Current MST configuration
Name [korenix]
Revision 65535
Instance Vlans Mapped
-------- --------------------------------------
0 1,4-4094
1 2
2 3
------------------------------------------------
Config HMAC-MD5 Digest:
0xB41829F9030A054FB74EF7A8587FF58D
------------------------------------------------
Remove Region Switch(config-mst)# no
Name name name configure
revision revision configure
instance the mst instance
Switch(config-mst)# no name
Remove Instance Switch(config-mst)# no instance
example <1-15> target instance number
Switch(config-mst)# no instance 2
Show Pending MST Switch(config-mst)# show pending
Configuration Pending MST configuration
Name [] (->The name is removed by no name)
Revision 65535
Instance Vlans Mapped
-------- --------------------------------------
0 1,3-4094
1 2 (->Instance 2 is removed by no instance 2)
------------------------------------------------
Config HMAC-MD5 Digest:
0x3AB68794D602FDF43B21C0B37AC3BCA8
------------------------------------------------
Apply the setting and Switch(config-mst)# quit
go to the apply all mst configuration changes
configuration mode Switch(config)#
Apply the setting and Switch(config-mst)# end
go to the global mode apply all mst configuration changes
Switch#
Abort the Setting and Switch(config-mst)# abort
go to the discard all mst configuration changes
configuration mode. Switch(config)# spanning-tree mst configuration
Switch(config-mst)# show pending
Show Pending to see Pending MST configuration
the new settings are Name [korenix] (->The nameis not applied after Abort settings.)
not applied. Revision 65535
Instance Vlans Mapped
-------- --------------------------------------
0 1,4-4094
1 2
2 3 (-> The instance is not applied after Abort settings.)
------------------------------------------------
Config HMAC-MD5 Digest:
0xB41829F9030A054FB74EF7A8587FF58D
------------------------------------------------
RSTP

75
System RSTP Setting The mode should be rst, the timings can be configured in global
settings listed in above.
Port Configuration Mode
Port Configuraiton Switch(config)# interface fa1
Switch(config-if)# spanning-tree
bpdufilter a secure BPDU process on edge-port interfcae
bpduguard a secure response to invalid
configurations(received BPDU sent by self)
cost change an interafce's spanning-tree port path cost
edge-port interface attached to a LAN segment that is at the
end of a bridged LAN or to an end node
link-type the link type for the Rapid Spanning Tree
mst the multiple spanning-tree
port-priority the spanning tree port priority
Port Path Cost Switch(config-if)# spanning-tree cost
<1-200000000> 16-bit based value range from 1-65535, 32-bit based
value range
from 1-200,000,000
Switch(config-if)# spanning-tree cost 200000
Port Priority Switch(config-if)# spanning-tree port-priority
<0-240> Number from 0 to 240, in multiple of 16
Switch(config-if)# spanning-tree port-priority 128
Link Type - Auto Switch(config-if)# spanning-tree link-type auto
Link Type - P2P Switch(config-if)# spanning-tree link-type point-to-point
Link Type – Share Switch(config-if)# spanning-tree link-type shared
Edge Port Switch(config-if)# spanning-tree edge-port enable
Switch(config-if)# spanning-tree edge-port disable
MSTP Port Switch(config-if)# spanning-tree mst MSTMAP cost
Configuration <1-200000000> the value of mst instance port cost
Switch(config-if)# spanning-tree mst MSTMAP port-priority
<0-240> the value of mst instance port priority in multiple of 16
Global Information
Active Information Switch# show spanning-tree active
Spanning-Tree : Enabled Protocol : MSTP
Root Address : 0012.77ee.eeee Priority : 32768
Root Path Cost : 0 Root Port : N/A
Root Times : max-age 20, hello-time 2, forward-delay 15
Bridge Address : 0012.77ee.eeee Priority : 32768
Bridge Times : max-age 20, hello-time 2, forward-delay 15
BPDU transmission-limit : 3

Port Role State Cost Prio.Nbr Type Aggregated

------ ---------- ---------- -------- ---------- ------------ ------------
fa1 Designated Forwarding 200000 128.1 P2P(RSTP) N/A
fa2 Designated Forwarding 200000 128.2 P2P(RSTP) N/A
RSTP Summary Switch# show spanning-tree summary
Switch is in rapid-stp mode.
BPDU skewing detection disabled for the bridge.
Backbonefast disabled for bridge.
Summary of connected spanning tree ports :
#Port-State Summary
Blocking Listening Learning Forwarding Disabled
-------- --------- -------- ---------- --------
0 0 0 2 8
#Port Link-Type Summary
AutoDetected PointToPoint SharedLink EdgePort
------------ ------------ ---------- --------

76
 9 0 1 9
Port Info Switch# show spanning-tree port detail fa7 (Interface_ID)
Rapid Spanning-Tree feature Enabled
Port 128.6 as Disabled Role is in Disabled State
Port Path Cost 200000, Port Identifier 128.6
RSTP Port Admin Link-Type is Auto, Oper Link-Type is Point-to-Point
RSTP Port Admin Edge-Port is Enabled, Oper Edge-Port is Edge
Designated root has priority 32768, address 0012.7700.0112
Designated bridge has priority 32768, address 0012.7760.1aec
Designated Port ID is 128.6, Root Path Cost is 600000
Timers : message-age 0 sec, forward-delay 0 sec

Link Aggregation Group: N/A, Type: N/A, Aggregated with: N/A

BPDU: sent 43759 , received 4854

TCN : sent 0 , received 0
Forwarding-State Transmit count 12
Message-Age Expired count
MSTP Information
MSTP Configuraiton Switch# show spanning-tree mst configuration
Current MST configuration (MSTP is Running)
Name [korenix]
Revision 65535
Instance Vlans Mapped
-------- --------------------------------------
0 1,4-4094
1 2
2 3
------------------------------------------------
Config HMAC-MD5 Digest:
0xB41829F9030A054FB74EF7A8587FF58D
------------------------------------------------
Display all MST Switch# show spanning-tree mst
Information ###### MST00 vlans mapped: 1,4-4094
Bridge address 0012.77ee.eeee priority 32768 (sysid 0)
Root this switch for CST and IST
Configured max-age 2, hello-time 15, forward-delay 20, max-hops 20

Port Role State Cost Prio.Nbr Type

------ ---------- ---------- -------- ---------- ------------------
fa1 Designated Forwarding 200000 128.1 P2P Internal(MSTP)
fa2 Designated Forwarding 200000 128.2 P2P Internal(MSTP)

###### MST01 vlans mapped: 2

Bridge address 0012.77ee.eeee priority 32768 (sysid 1)
Root this switch for MST01

Port Role State Cost Prio.Nbr Type

------ ---------- ---------- -------- ---------- ------------------
fa1 Designated Forwarding 200000 128.1 P2P Internal(MSTP)
fa2 Designated Forwarding 200000 128.2 P2P Internal(MSTP)
MSTP Root Switch# show spanning-tree mst root
Information MST Root Root Root Root Max Hello Fwd
Instance Address Priority Cost Port age dly
-------- -------------- -------- ----------- ------ ----- ----- -----
MST00 0012.77ee.eeee 32768 0 N/A 20 2 15
MST01 0012.77ee.eeee 32768 0 N/A 20 2 15

77
 MST02 0012.77ee.eeee 32768 0 N/A 20 2 15
MSTP Instance Switch# show spanning-tree mst 1
Information ###### MST01 vlans mapped: 2
Bridge address 0012.77ee.eeee priority 32768 (sysid 1)
Root this switch for MST01

Port Role State Cost Prio.Nbr Type

------ ---------- ---------- -------- ---------- ------------------
fa1 Designated Forwarding 200000 128.1 P2P Internal(MSTP)
fa2 Designated Forwarding 200000 128.2 P2P Internal(MSTP)
MSTP Port Switch# show spanning-tree mst interface fa1
Information Interface fastethernet1 of MST00 is Designated Forwarding
Edge Port : Edge (Edge) BPDU Filter : Disabled
Link Type : Auto (Point-to-point) BPDU Guard : Disabled
Boundary : Internal(MSTP)
BPDUs : sent 6352, received 0

Instance Role State Cost Prio.Nbr Vlans

mapped
-------- ---------- ---------- -------- ---------- ---------------------
0 Designated Forwarding 200000 128.1 1,4-4094
1 Designated Forwarding 200000 128.1 2
2 Designated Forwarding 200000 128.1 3
Multiple Super Ring
Create or configure a Switch(config)# multiple-super-ring 1
Ring Ring 1 created
Switch(config-multiple-super-ring)#
Note: 1 is the target Ring ID which is going to be created or
configured.
Super Ring Version Switch(config-multiple-super-ring)# version
any-ring any ring auto detection
default set default to rapid super ring
rapid-super-ring rapid super ring
super-ring super ring

Switch(config-multiple-super-ring)# version rapid-super-ring

Priority Switch(config-multiple-super-ring)# priority
<0-255> valid range is 0 to 255
default set default
Switch(config)# super-ring priority 100
Ring Port Switch(config-multiple-super-ring)# port
IFLIST Interface list, ex: fa1,fa3-5,gi8-10
cost path cost
Switch(config-multiple-super-ring)# port fa1,fa2
Ring Port Cost Switch(config-multiple-super-ring)# port cost
<0-255> valid range is 0 or 255
default set default (128)valid range is 0 or 255
Switch(config-multiple-super-ring)# port cost 100
<0-255> valid range is 0 or 255
default set default (128)valid range is 0 or 255
Switch(config-super-ring-plus)# port cost 100 200
Set path cost success.
Rapid Dual Homing Switch(config-multiple-super-ring)# rapid-dual-homing enable

Switch(config-multiple-super-ring)# rapid-dual-homing disable

Switch(config-multiple-super-ring)# rapid-dual-homing port

78
 IFLIST Interface name, ex: fastethernet1 or gi8
auto-detect up link auto detection
IFNAME Interface name, ex: fastethernet1 or gi8
Switch(config-multiple-super-ring)# rapid-dual-homing port fa3,fa5-6
set Rapid Dual Homing port success.
Note: auto-detect is recommended for dual Homing..
Ring Info
Ring Info Switch# show multiple-super-ring [Ring ID]
[Ring1] Ring1
Current Status : Disabled
Role : Disabled
Ring Status : Abnormal
Ring Manager : 0000.0000.0000
Blocking Port : N/A
Giga Copper : N/A
Configuration :
Version : Rapid Super Ring
Priority : 128
Ring Port : fa1, fa2
Path Cost : 100, 200
Dual-Homing II : Disabled
Statistics :
Watchdog sent 0, received 0, missed 0
Link Up sent 0, received 0
Link Down sent 0, received 0
Role Transition count 0
Ring State Transition count 1

Ring ID is optional. If the ring ID is typed, this command will only

display the information of the target Ring.

79
4.5 VLAN
A Virtual LAN (VLAN) is a “logical” grouping of nodes for the purpose of
limiting a broadcast domain to specific members of a group without
physically grouping the members together. That means, VLAN allows you
to isolate network traffic so that only members of VLAN could receive traffic
from the same VLAN members. Basically, creating a VLAN from a switch is
the logical equivalent of physically reconnecting a group of network devices
to another Layer 2 switch, without actually disconnecting these devices
from their original switches.
JetNet 4508 / 4508f Series Industrial Ethernet Switch supports 802.1Q
VLAN. 802.1Q VLAN is also known as Tag-Based VLAN. This Tag-Based
VLAN allows VLAN to be created across different switches (see Figure 1).
IEEE 802.1Q tag-based VLAN makes use of VLAN control information
stored in a VLAN header attached to IEEE 802.3 packet frames. This tag
contains a VLAN Identifier (VID) that indicates which VLAN a frame
belongs to. Since each switch only has to check a frame’s tag, without the
need to dissect the contents of the frame, this also saves a lot of computing
resources within the switch.
Figure 4.5-1 802.1Q VLAN

VLAN Configuration group enables you to Add/Remove VLAN, configure

port Ingress/Egress parameters and view VLAN table.

80
 Following commands are included in this group:
4.5.1 VLAN Port Configuration
4.5.2 VLAN Configuration
4.5.3 GVRP Configuration
4.5.4 VLAN Table
4.5.5 CLI Commands of the VLAN

4.5.1 VLAN Port Configuration

VLAN Port Configuration allows you to set up VLAN port parameters to
specific port. These parameters include PVID, Accept Frame Type and
Ingress Filtering.

Figure 4.5-2 Web UI of VLAN configuration.

PVID: The abbreviation of the Port VLAN ID. Enter port VLAN ID here.
PVID allows the switches to identify which port belongs to which VLAN. To
keep things simple, it is recommended that PVID is equivalent to VLAN IDs.
The values of PVIDs are from 0 to 4095. But, 0 and 4095 are reserved. You
can’t input these 2 PVIDs. 1 is the default value. 2 to 4094 are valid and
available in this column. Type the PVID you’d like to configure here.
Accept Frame Type: This column defines the accepted frame type of the
port. There are 2 modes you can select, Admit All and Tag Only. Admit All

81
 mode means that the port can accept both tagged and untagged packets.
Tag Only mode means that the port can only accept tagged packets.
Ingress Filtering: Ingress filtering helps VLAN engine to filter out
undesired traffic on a port. When Ingress Filtering is enabled, the port
checks whether the incoming frames belong to the VLAN they claimed or
not. Then the port determines if the frames can be processed or not. For
example, if a tagged frame from Engineer VLAN is received, and Ingress
Filtering is enabled, the switch will determine if the port is on the Engineer
VLAN’s Egress list. If it is, the frame can be processed. If it’s not, the frame
would be dropped.

4.5.2 VLAN Configuration

In this page, you can assign Management VLAN, create the static VLAN,
and assign the Egress rule for the member ports of the VLAN.
Figure 4.5-3 Web UI of the VLAN Configuration.

Sample of JetNet 5010G

Management VLAN ID: The switch supports management VLAN. The

management VLAN ID is the VLAN ID of the CPU interface so that only
member ports of the management VLAN can ping and access the switch.
The default management VLAN ID is 1.

82
Static VLAN: You can assign a VLAN ID and VLAN Name for new VLAN
here.
VLAN ID is used by the switch to identify different VLANs. Valid VLAN ID is
between 1 and 4094. 1 is the default VLAN.
VLAN Name is a reference for network administrator to identify different
VLANs. The available character is 12 for you to input. If you don’t input
VLAN name, the system will automatically assign VLAN name for the VLAN.
The rule is VLAN (VLAN ID).

Figure 4.5-4 The steps to create a new VLAN:

Type VLAN ID and NAME, and press Add to
create a new VLAN. Then you can see the new
VLAN in the Static VLAN Configuration table.
Refer to Figure 4.5-5
After created the VLAN, the status of the VLAN
will remain in Unused until you add ports to the VLAN.
Note: Before you change the management VLAN ID by Web and Telnet,
remember that the port attached by the administrator should be the
member port of the management VLAN; otherwise the administrator can’t
access the switch via the network.
Note: Currently JetNet 4508/4508f only support max 256 groups VLAN.

Static VLAN Configuration

You can see the created VLANs and specify the egress (outgoing) port rule
to be Untagged or Tagged here.
Figure 4.5-5 below shows the Static VLAN Configuration table. You can
see that new VLAN 3 (test) is created and the Egress rules of the ports are
not configured now.

Sample of JetNet 5010G

83
 Figure 4.5.2.4 Configure Egress rule of the ports.

Sample of JetNet 5010G

-- : Not available
U: Untag: Indicates that egress/outgoing frames are not VLAN tagged.
T : Tag: Indicates that egress/outgoing frames are to be VLAN tagged.
Steps to configure Egress rules: Select the VLAN ID. Entry of the selected
VLAN turns to light blue. Assign Egress rule of the ports to U or T. Press
Apply to apply the setting. If you want to remove one VLAN, select the
VLAN entry. Then press Remove button.

4.5.3 GVRP configuration

GVRP allows users to set-up VLANs automatically rather than manual
configuration on every port of every switch in the network.

Sample of JetNet 5010G

84
 GVRP Protocol: Allow user to enable/disable GVRP globally.
State: After enable GVRP globally, here still can enable/disable GVRP by
port.
Join Timer: Controls the interval of sending the GVRP Join BPDU. An
instance of this timer is required on a per-Port, per-GARP Participant basis
Leave Timer: Control the time to release the GVRP reservation after
received the GVRP Leave BPDU. An instance of the timer is required for
each state machine that is in the LV state
Leave All Timer: Controls the period to initiate the garbage collection of
registered VLAN. The timer is required on a per-Port, per-GARP Participant
basis

4.5.4 VLAN Table

This table shows you current settings of your VLAN table, including VLAN
ID, Name, Status, and Egress rule of the ports.

Sample of JetNet 5010G

VLAN ID: ID of the VLAN.

Name: Name of the VLAN.
Status: Static shows this is a manually configured static VLAN. Unused
means this VLAN is created by UI/CLI and has no member ports. This
VLAN is not workable yet. Dynamic means this VLAN is learnt by GVRP.
After created the VLAN, the status of this VLAN will remain in Unused
status until you add ports to the VLAN.

85
4.5.5 CLI Commands of the VLAN
Command Lines of the VLAN port configuration, VLAN configuration and
VLAN table display

Feature Command Line

VLAN Port Configuration
VLAN Port PVID Switch(config-if)# switchport trunk native vlan 2
Set port default vlan id to 2 success
Port Accept Frame Switch(config)# inter fa1
Type Switch(config-if)# acceptable frame type all
any kind of frame type is accepted!
Switch(config-if)# acceptable frame type vlantaggedonly
only vlan-tag frame is accepted!
Ingress Filtering (for Switch(config)# interface fa1
fast Ethernet port 1) Switch(config-if)# ingress filtering enable
ingress filtering enable
Switch(config-if)# ingress filtering disable
ingress filtering disable
Egress rule – Untagged Switch(config-if)# switchport access vlan 2
(for VLAN 2) switchport access vlan - success
Egress rule – Tagged Switch(config-if)# switchport trunk allowed vlan add 2
(for VLAN 2)
Display – Port Ingress Switch# show interface fa1
Rule (PVID, Ingress Interface fastethernet1
Filtering, Acceptable Administrative Status : Enable
Frame Type) Operating Status : Not Connected
Duplex : Auto
Speed : Auto
Flow Control :off
Default Port VLAN ID: 2
Ingress Filtering : Disabled
Acceptable Frame Type : All
Port Security : Disabled
Auto Negotiation : Enable
Loopback Mode : None
STP Status: disabled
Default CoS Value for untagged packets is 0.
Mdix mode is Auto.
Medium mode is Copper.

Display – Port Egress Switch# show running-config

Rule (Egress rule, IP ……
address, status) !
interface gigabitethernet1
switchport access vlan 1
switchport access vlan 3
switchport trunk native vlan 2
…….
interface vlan1
ip address 192.168.10.8/24
no shutdown

VLAN Configuration

86
Create VLAN (2) Switch(config)# vlan 2
vlan 2 success

Switch(config)# interface vlan 2

Switch(config-if)#

Note: In CLI configuration, you should create a VLAN

interface first. Then you can start to add/remove ports.
Default status of the created VLAN is unused until you add
member ports to it.
Remove VLAN Switch(config)# no vlan 2
no vlan success

Note: You can only remove the VLAN when the VLAN is in
unused mode.
VLAN Name Switch(config)# vlan 2
vlan 2 has exists
Switch(config-vlan)# name v2

Switch(config-vlan)# no name

Note: Use no name to change the name to default name,

VLAN VID.
VLAN description Switch(config)# interface vlan 2
Switch(config-if)#
Switch(config-if)# description this is the VLAN 2

Switch(config-if)# no description ->Delete the description.

IP address of the VLAN Switch(config)# interface vlan 2
Switch(config-if)#
Switch(config-if)# ip address 192.168.10.18/24

Switch(config-if)# no ip address 192.168.10.8/24 ->Delete

the IP address
Create multiple VLANs Switch(config)# interface vlan 5-10
(VLAN 5-10)
Shut down VLAN Switch(config)# interface vlan 2
Switch(config-if)# shutdown

Switch(config-if)# no shutdown ->Turn on the VLAN

Display – VLAN table Switch# sh vlan

VLAN Name Status Trunk Ports Access Ports
---- ------------ ------- -------------------------- --------------------------
1 VLAN1 Static - fa1-7
2 VLAN2 Unused - -
3 test Static fa4-5 fa3,fa4,fa7-8
Display – VLAN Switch# show interface vlan1
interface information interface vlan1 is up, line protocol detection is disabled
index 14 metric 1 mtu 1500 <UP,BROADCAST,RUNNING,MULTICAST>
HWaddr: 00:12:77:ff:01:b0
inet 192.168.10.100/24 broadcast 192.168.10.255
input packets 639, bytes 38248, dropped 0, multicast packets 0
input errors 0, length 0, overrun 0, CRC 0, frame 0, fifo 0, missed 0
output packets 959, bytes 829280, dropped 0
output errors 0, aborted 0, carrier 0, fifo 0, heartbeat 0, window 0
collisions 0
GVRP configuration
GVRP enable/disable Switch(config)# gvrp mode

87
 disable Disable GVRP feature globally on the switch
enable Enable GVRP feature globally on the switch
Switch(config)# gvrp mode enable
Gvrp is enabled on the switch!
Configure GVRP timer Switch(config)# inter fa1
Switch(config-if)# garp timer
Join timer /Leave timer/ <10-10000>
LeaveAll timer Switch(config-if)# garp timer 20 60 1000
Note: The unit of these timer is centisecond
Management VLAN
Management VLAN Switch(config)# int vlan 1 (Go to management VLAN)
Switch(config-if)# no shutdown
Display Switch# show running-config
….
!
interface vlan1
ip address 192.168.10.17/24
ip igmp
no shutdown
!
….

4.6 Private VLAN

The private VLAN helps to resolve the primary VLAN ID shortage, client
ports’ isolation and network security issues. The Private VLAN provides
primary and secondary VLAN within a single switch.
Primary VLAN: The uplink port is usually the primary VLAN. A primary
VLAN contains promiscuous ports that can communicate with lower
Secondary VLANs.
Secondary VLAN: The client ports are usually defined within secondary
VLAN. The secondary VLAN includes Isolated VLAN and Community
VLAN. The client ports can be isolated VLANs or can be grouped in the
same Community VLAN. The ports within the same community VLAN can
communicate with each other. However, the isolated VLAN ports can Not.
The figure shows the typical Private VLAN network. The SCADA/Public
Server or NMS workstation is usually located in primary VLAN. The clients
PCs or Rings are located within Secondary.

88
 Private VLAN (PVLAN) Configuration group enables you to Configure
PVLAN, PVLAN Port and see the PVLAN Information.
Following commands are included in this group:
4.6.1 PVLAN Configuration
4.6.2 PVLAN Port Configuration
4.6.3 CLI Commands of the PVLAN

4.6.1 PVLAN Configuration

PVLAN Configuration allows you to assign Private VLAN type. After created
VLAN in VLAN Configuraiton page, the available VLAN ID will display here.
Choose the Private VLAN types for each VLAN you want configure.
None: The VLAN is Not included in Private VLAN.
Primary: The VLAN is the Primary VLAN. The member ports can
communicate with secondary ports.
Isolated: The VLAN is the Isolated VLAN. The member ports of the VLAN
are isolated.
Community: The VLAN is the Community VLAN. The member ports of the
VLAN can communicate with each other.

4.6.2 PVLAN Port Configuration

PVLAN Port Configuration page allows configure Port Configuration and
Private VLAN Association.

Private VLAN Association

89
Secondary VLAN: After the Isolated and Community VLAN Type is
assigned in Private VLAN Configuration page, the VLANs are belonged to
the Secondary VLAN and displayed here.
Primary VLAN: After the Primary VLAN Type is assigned in Private VLAN
Configuration page, the secondary VLAN can associate to the Primary
VLAN ID. Select the Primary VLAN ID here.
Note: Before configuring PVLAN port type, the Private VLAN Association
should be done first.

Port Configuraion
PVLAN Port Type :
Normal: The Normal port is None PVLAN ports, it remains its original
VLAN setting.
Host: The Host type ports can be mapped to the Secondary VLAN.
Promiscuous: The promiscuous port can be associated to the Primary
VLAN.
VLAN ID: After assigned the port type, the web UI display the available
VLAN ID the port can associate to.

For example:
1. VLAN Create: VLAN 2-5 are created in VLAN Configuration page.
2. Private VLAN Type: VLAN 2-5 has its Private VLAN Type configured in
Private VLAN Configuration page.
VLAN 2 is belonged to Primary VLAN.
VLAN 3-5 are belonged to secondary VLAN (Isolated or Community).
3. Private VLAN Association: Associate VLAN 3-5 to VLAN 2 in Private
VLAN Association first.
4. Private VLAN Port Configuraiton
VLAN 2 – Primary -> The member port of VLAN 2 is promiscuous port.
VLAN 3 – Isolated -> The Host port can be mapped to VLAN 3.
VLAN 4 – Community -> The Host port can be mapped to VLAN 3.
VLAN 5 – Community -> The Host port can be mapped to VLAN 3.
5. Result:
VLAN 2 -> VLAN 3, 4, 5; member ports can communicate with ports in
secondary VLAN.
VLAN 3 -> VLAN 2, member ports are isolated, but it can communicate with
member port of VLAN 2..
VLAN 4 -> VLAN 2, member ports within the community can communicate
with each other and communicate with member port of VLAN 2.
VLAN 5 -> VLAN 2, member ports within the community can communicate
with each other and communicate with member port of VLAN 2.

90
4.6.3 Private VLAN Information
This page allows you to see the Private VLAN information.

91
4.6.4 CLI Command of the PVLAN
Command Lines of the Private VLAN configuration

Feature Command Line

Private VLAN Configuration
Create VLAN Switch(config)# vlan 2
vlan 2 success
Switch(config-vlan)#
end End current mode and change to enable mode
exit Exit current mode and down to previous mode
list Print command list
name Assign a name to vlan
no no
private-vlan Configure a private VLAN

Private VLAN Type Go to the VLAN you want configure first.

Switch(config)# vlan (VID)

Choose the Types Switch(config-vlan)# private-vlan

community Configure the VLAN as an community private
VLAN
isolated Configure the VLAN as an isolated private VLAN
primary Configure the VLAN as a primary private VLAN

Primary Type Switch(config-vlan)# private-vlan primary

<cr>

Isolated Type Switch(config-vlan)# private-vlan isolated

<cr>

Community Type Switch(config-vlan)# private-vlan community

<cr>
Private VLAN Port Configuraiton
Go to the port Switch(config)# interface (port_number, ex: gi9)
configuraiton Switch(config-if)# switchport private-vlan
host-association Set the private VLAN host association
mapping map primary VLAN to secondary VLAN

Private VLAN Port Type Switch(config-if)# switchport mode

private-vlan Set private-vlan mode
Switch(config-if)# switchport mode private-vlan
host Set the mode to private-vlan host
promiscuous Set the mode to private-vlan promiscuous
Promiscuous Port Type Switch(config-if)# switchport mode private-vlan promiscuous
<cr>

Host Port Type Switch(config-if)# switchport mode private-vlan host

<cr>

Private VLAN Port Switch(config)# interface gi9

Configuration
PVLAN Port Type Switch(config-if)# switchport mode private-vlan host

Host Association Switch(config-if)# switchport private-vlan host-association

92
primary to secondary <2-4094> Primary range VLAN ID of the private VLAN port
association
(The command is only Switch(config-if)# switchport private-vlan host-association 2
available for host port.) <2-4094> Secondary range VLAN ID of the private VLAN port
association
Switch(config-if)# switchport private-vlan host-association 2 3

Mapping primary to Switch(config)# interface gi10

secondary VLANs
Switch(config-if)# switchport mode private-vlan promiscuous
(This command is only
available for Switch(config-if)# switchport private-vlan mapping 2 add 3
promiscuous port) Switch(config-if)# switchport private-vlan mapping 2 add 4
Switch(config-if)# switchport private-vlan mapping 2 add 5

Private VLAN Information

Private VLAN Switch# show vlan private-vlan
Information FLAGS: I -> Isolated P -> Promiscuous
C -> Community
Primary Secondary Type Ports
------- --------- ----------------- ---------------------
2 3 Isolated gi10(P),gi9(I)
2 4 Community gi10(P),gi8(C)
2 5 Community gi10(P),fa7(C),gi9(I)
10 - - -

PVLAN Type Switch# show vlan private-vlan type

Vlan Type Ports
---- ----------------- -----------------
2 primary gi10
3 isolated gi9
4 community gi8
5 community fa7,gi9
10 primary -
Host List Switch# show vlan private-vlan port-list
Ports Mode Vlan
----- ----------- ----
1 normal -
2 normal -
3 normal -
4 normal -
5 normal -
6 normal -
7 host 5
8 host 4
9 host 3
10 promiscuous 2
Running Config Switch# show run
Information Building configuration...

Current configuration:
hostname Switch
vlan learning independent
!
vlan 1
!
Private VLAN Type vlan 2

93
 private-vlan primary
!
vlan 3
private-vlan isolated
!
vlan 4
private-vlan community
!
vlan 5
private-vlan community
!
………..
………..
Private VLAN Port interface fastethernet7
Information switchport access vlan add 2,5
switchport trunk native vlan 5
switchport mode private-vlan host
switchport private-vlan host-association 2 5
!
interface gigabitethernet8
switchport access vlan add 2,4
switchport trunk native vlan 4
switchport mode private-vlan host
switchport private-vlan host-association 2 4
!
interface gigabitethernet9
switchport access vlan add 2,5
switchport trunk native vlan 5
switchport mode private-vlan host
switchport private-vlan host-association 2 3
!
interface gigabitethernet10
switchport access vlan add 2,5
switchport trunk native vlan 2
switchport mode private-vlan promiscuous
switchport private-vlan mapping 2 add 3-5
………
……..

94
4.7 Traffic Prioritization
Quality of Service (QoS) provides traffic prioritization mechanism which
allows users to deliver better service to certain flows. QoS can also help to
alleviate congestion problems and ensure high-priority traffic is delivered
first. This section allows you to configure Traffic Prioritization settings for
each port with regard to setting priorities.
JetNet switch’s QOS supports 4 physical queues, weighted fair queuing
(WRR) and Strict Priority scheme, which follows 802.1p COS tag and IPv4
TOS/DiffServ information to prioritize the traffic of your industrial network.
Following commands are included in this group:
4.7.1 QoS Setting
4.7.2 CoS-Queue Mapping
4.7.3 DSCP-Queue Mapping
4.7.4 CLI Commands of the Traffic Prioritization

4.7.1 QoS Setting

95
 Queue Scheduling
You can select the Queue Scheduling rule as follows:
Use an 8,4,2,1 weighted fair queuing scheme. This is also known as
WRR (Weight Round Robin). JetNet will follow 8:4:2:1 rate to process the
packets in a queue from the highest priority to the lowest. For example, the
system will process 8 packets with the highest priority in the queue, 4 with
middle priority, and 2 with low priority, and 1 with the lowest priority at the
same time.
Use a strict priority scheme. Packets with higher priority in the queue will
always be processed first, except that there is no packet with higher priority.

Port Setting
CoS column is to indicate default port priority value for untagged or
priority-tagged frames. When JetNet receives the frames, JetNet will attach
the value to the CoS field of the incoming VLAN-tagged packets. You can
enable 0,1,2,3,4,5,6 or 7 to the port.
Trust Mode is to indicate Queue Mapping types for you to select.
COS Only: Port priority will only follow COS-Queue Mapping you have
assigned.
DSCP Only: Port priority will only follow DSCP-Queue Mapping you have
assigned.
COS first: Port priority will follow COS-Queue Mapping first, and then
DSCP-Queue Mapping rule.
DSCP first: Port priority will follow DSCP-Queue Mapping first, and then
COS-Queue Mapping rule.
Default priority type is COS Only. The system will provide default
COS-Queue table to which you can refer for the next command.
After configuration, press Apply to enable the settings.

4.7.2 CoS-Queue Mapping

This page is to change CoS values to Physical Queue mapping table. Since
the switch fabric of JetNet only supports 4 physical queues, Lowest, Low,
Middle and High. Users should therefore assign how to map CoS value to
the level of the physical queue.
In JetNet management switch, users can freely assign the mapping table or
follow the suggestion of the 802.1p standard. Korenix uses 802.1p
suggestion as default values. You can find CoS values 1 and 2 are mapped
to physical Queue 0, the lowest queue. CoS values 0 and 3 are mapped to
physical Queue 1, the low/normal physical queue. CoS values 4 and 5 are
mapped to physical Queue 2, the middle physical queue. CoS values 6 and
7 are mapped to physical Queue 3, the high physical queue.

96
 After configuration, press Apply to enable the settings.

4.7.3 DSCP-Queue Mapping

This page is to change DSCP values to Physical Queue mapping table.
Since the switch fabric of JetNet only supports 4 physical queues, Lowest,
Low, Middle and High. Users should therefore assign how to map DSCP
value to the level of the physical queue. In JetNet, users can freely change
the mapping table to follow the upper layer 3 switch or routers’ DSCP
setting.

After configuration, press Apply to enable the settings.

97
4.7.4 CLI Commands of the Traffic Prioritization
Command Lines of the Traffic Prioritization configuration

Feature Command Line

QoS Setting
Queue Scheduling – Switch(config)# qos queue-sched
Strict Priority sp Strict Priority
wrr Weighted Round Robin (Use an 8,4,2,1 weight)
Switch(config)# qos queue-sched sp
<cr>
Queue Scheduling - Switch(config)# qos queue-sched wrr
WRR
Port Setting – CoS Switch(config)# interface fa1
(Default Port Priority) Switch(config-if)# qos cos
DEFAULT-COS Assign an priority (7 highest)
Switch(config-if)# qos cos 7
The default port CoS value is set 7 ok.

Note: When change the port setting, you should Select the
specific port first. Ex: fa1 means fast Ethernet port 1.
Port Setting – Trust Switch(config)# interface fa1
Mode- CoS Only Switch(config-if)# qos trust cos
The port trust is set CoS only ok.
Port Setting – Trust Switch(config)# interface fa1
Mode- CoS First Switch(config-if)# qos trust cos-first
The port trust is set CoS first ok.
Port Setting – Trust Switch(config)# interface fa1
Mode- DSCP Only Switch(config-if)# qos trust dscp
The port trust is set DSCP only ok.
Port Setting – Trust Switch(config)# interface fa1
Mode- DSCP First Switch(config-if)# qos trust dscp-first
The port trust is set DSCP first ok.
Display – Queue Switch# show qos queue-sched
Scheduling QoS queue scheduling scheme : Weighted Round Robin (Use
an 8,4,2,1 weight)
Display – Port Setting - Switch# show qos trust
Trust Mode QoS Port Trust Mode :
Port Trust Mode
-----+------------
1 DSCP first
2 COS only
3 COS only
4 COS only
5 COS only
6 COS only
7 COS only
8 COS only

Display – Port Setting – Switch# show qos port-cos

CoS (Port Default Port Default Cos :
Priority) Port CoS
-----+----
1 7
2 0
3 0

98
 4 0
5 0
6 0
7 0
8 0

CoS-Queue Mapping
Format Switch(config)# qos cos-map
PRIORITY Assign an priority (7 highest)
Switch(config)# qos cos-map 1
QUEUE Assign an queue (0-3)

Note: Format: qos cos-map priority_value queue_value

Map CoS 0 to Queue 1 Switch(config)# qos cos-map 0 1

The CoS to queue mapping is set ok.
Map CoS 1 to Queue 0 Switch(config)# qos cos-map 1 0
The CoS to queue mapping is set ok.
Map CoS 2 to Queue 0 Switch(config)# qos cos-map 2 0
The CoS to queue mapping is set ok.
Map CoS 3 to Queue 1 Switch(config)# qos cos-map 3 1
The CoS to queue mapping is set ok.
Map CoS 4 to Queue 2 Switch(config)# qos cos-map 4 2
The CoS to queue mapping is set ok.
Map CoS 5 to Queue 2 Switch(config)# qos cos-map 5 2
The CoS to queue mapping is set ok.
Map CoS 6 to Queue 3 Switch(config)# qos cos-map 6 3
The CoS to queue mapping is set ok.
Map CoS 7 to Queue 3 Switch(config)# qos cos-map 7 3
The CoS to queue mapping is set ok.
Display – CoS-Queue Switch# sh qos cos-map
mapping CoS to Queue Mapping :
CoS Queue
---- + ------
0 1
1 0
2 0
3 1
4 2
5 2
6 3
7 3
DSCP-Queue Mapping
Format Switch(config)# qos dscp-map
PRIORITY Assign an priority (63 highest)
Switch(config)# qos dscp-map 0
QUEUE Assign an queue (0-3)

Format: qos dscp-map priority_value queue_value

Map DSCP 0 to Queue Switch(config)# qos dscp-map 0 1

1 The TOS/DSCP to queue mapping is set ok.

Display – DSCO-Queue Switch# show qos dscp-map

mapping DSCP to Queue Mapping : (dscp = d1 d2)

d2| 0 1 2 3 4 5 6 7 8 9

99
 d1 |
-----+----------------------
0|1111111100
1|0000000000
2|0000111111
3|1122222222
4|2222222233
5|3333333333
6|3333

4.8 Multicast Filtering

For multicast filtering, JetNet 4508/4508f uses IGMP Snooping technology.
IGMP (Internet Group Management Protocol) is an Internet Protocol that
provides a way for internet device to report its multicast group membership
to adjacent routers. Multicasting allows one computer on the internet to
send data to a multitude of other computers that have identified themselves
as being interested in receiving the originating computers data.
Multicasting is useful for such applications as updating the address books
of mobile computer users in the field, sending out newsletters to a
distribution list, and broadcasting streaming media to an audience that has
tuned into the event by setting up multicast group membership.
In effect, IGMP Snooping manages multicast traffic by making use of
switches, routers, and hosts that support IGMP. Enabling IGMP Snooping
allows the ports to detect IGMP queries, report packets, and manage
multicast traffic through the switch. IGMP has three fundamental types of
messages, as shown below:

Message Description
Query A message sent from the querier (an IGMP router or a switch) which
asks for a response from each host that belongs to the multicast group.
Report A message sent by a host to the querier to indicate that the host wants
to be or is a member of a given group indicated in the report message.
Leave Group A message sent by a host to the querier to indicate that the host has
quit as a member of a specific multicast group.

You can enable IGMP Snooping and IGMP Query functions here. You will
see the information of the IGMP Snooping function in this section, including
different multicast groups’ VID and member ports, and IP multicast
addresses that range from 224.0.0.0 to 239.255.255.255.
In this section, Force filtering can determined whether the switch flooding
unknown multicast or not.
Following commands are included in this group:
4.8.1 IGMP Snooping
4.8.2 IGMP Query
4.8.3 Force Filtering

100
 4.8.4 CLI Commands of the Multicast Filtering

4.8.1 IGMP Snooping

This page is to enable IGMP Snooping feature, assign IGMP Snooping for
specific VLAN, and view IGMP Snooping table from dynamic learnt or static
manual key-in. JetNet Managed Switch support IGMP snooping V1/V2/V3
automatically and IGMP query V1/V2.
IGMP Snooping, you can select Enable or Disable here. After enabling
IGMP Snooping, you can then enable IGMP Snooping for specific VLAN.
You can enable IGMP Snooping for some VLANs so that some of the
VLANs will support IGMP Snooping and others won’t.
To assign IGMP Snooping to VLAN, please select the checkbox of VLAN
ID or select "Select All" checkbox for all VLANs. Then press Enable. In the
same way, you can also Disable IGMP Snooping for certain VLANs.

IGMP Snooping Table: In the table, you can see multicast group IP
address, VLAN ID it belongs to, and member ports of the multicast group.
JetNet Managed Switch supports 256 multicast groups. Click on Reload to
refresh the table.

Sample of JetNet 5010G

101
4.8.2 IGMP Query

This page allows users to configure IGMP Query feature. Since JetNet
Managed Switch can only be configured by member ports of the
management VLAN, IGMP Query can only be enabled on the management
VLAN. If you want to run IGMP Snooping feature in several VLANs, you
should notice that whether each VLAN has its own IGMP Querier first.
The IGMP querier periodically sends query packets to all end-stations on
the LANs or VLANs that are connected to it. For networks with more than
one IGMP querier, a switch with the lowest IP address becomes the IGMP
querier.
In IGMP Query selection, you can select V1, V2 or Disable. V1 means
IGMP V1 General Query and V2 means IGMP V2 General Query.. The
query will be forwarded to all multicast groups in the VLAN. Disable allows
you to disable IGMP Query.
Query Interval(s): The period of query sent by querier.
Query Maximum Response Time: The span querier detect to confirm
there are no more directly connected group members on a LAN.
Once you finish configuring the settings, click on Apply to apply your
configuration.

4.8.3 Force Filtering

The Force filtering function allows the switch to filter the unknown-multicast
data flow. If Force filtering is enabled, all the unknown multicast data will be

102
 discarded.

4.8.4 CLI Commands of the Multicast Filtering

Command Lines of the multicast filtering configuration

Feature Command Line

IGMP Snooping
IGMP Snooping - Switch(config)# ip igmp snooping
Global IGMP snooping is enabled globally. Please specify on which
vlans IGMP snooping enables
IGMP Snooping - VLAN Switch(config)# ip igmp snooping vlan
VLANLIST allowed vlan list
all all existed vlan
Switch(config)# ip igmp snooping vlan 1-2
IGMP snooping is enabled on VLAN 1-2.
Disable IGMP Snooping Switch(config)# no ip igmp snoopin
- Global IGMP snooping is disabled globally ok.
Disable IGMP Snooping Switch(config)# no ip igmp snooping vlan 3
- VLAN IGMP snooping is disabled on VLAN 3.
Display – IGMP Switch# sh ip igmp
Snooping Setting interface vlan1
enabled: Yes
version: IGMPv1
query-interval; 125s
query-max-response-time: 10s

Switch# sh ip igmp snooping

IGMP snooping is globally enabled
Vlan1 is IGMP snooping enabled
Vlan2 is IGMP snooping enabled
Vlan3 is IGMP snooping disabled

Display – IGMP Table Switch# sh ip igmp snooping multicast all

VLAN IP Address Type Ports
---- --------------- ------- ------------------------
1 239.192.8.0 IGMP fa6,
1 239.255.255.250 IGMP fa6,
IGMP Query
IGMP Query V1 Switch(config)# int vlan 1 (Go to management VLAN)
Switch(config-if)# ip igmp v1

IGMP Query V2 Switch(config)# int vlan 1 (Go to management VLAN)

Switch(config-if)# ip igmp

IGMP Query version Switch(config-if)# ip igmp version 1

Switch(config-if)# ip igmp version 2
Disable Switch(config)# int vlan 1
Switch(config-if)# no ip igmp
Display Switch# sh ip igmp
interface vlan1
enabled: Yes
version: IGMPv2
query-interval: 125s
query-max-response-time: 10s

103
 Switch# show running-config
….
!
interface vlan1
ip address 192.168.10.17/24
ip igmp
no shutdown
!
…….

Force filtering
Enable Force filtering Switch(config)# mac-address-table multicast filtering
Filtering unknown multicast addresses ok!
Disable Force filtering Switch(config)# no mac-address-table multicast filtering
Flooding unknown multicast addresses ok!

104
4.9 SNMP
Simple Network Management Protocol (SNMP) is a
protocol used for exchanging management
information between network devices. SNMP is a
member of the TCP/IP protocol suite. JetNet
Managed Switch series support SNMP v1 and v2c
and V3.
An SNMP managed network consists of two main
components: agents and a manager. An agent is a
management software module that resides in a
managed switch. An agent translates the local
management information from the managed device
into a SNMP compatible format. The manager is the
console through the network.
Following commands are included in this group:
4.9.1 SNMP Configuration
4.9.2 SNMPv3 Profile
4.9.3 SNMP Traps
4.9.4 SNMP CLI Commands for SNMP

4.9.1 SNMP Configuration

This page allows users to configure SNMP V1/V2c Community. The
community string can be viewed as the password because SNMP V1/V2c
doesn’t request you to enter password before you try to access SNMP
agent.
The community includes 2 privileges, Read Only and Read and Write.
With Read Only privilege, you only have the ability to read the values of
MIB tables. Default community string is Public.
With Read and Write privilege, you have the ability to read and set the
values of MIB tables. Default community string is Private.
JetNet Managed Switch allows users to assign 4 community strings. Type
the community string and select the privilege. Then press Apply.

Note: When you first install the device in your network, we highly
recommend you to change the community string. Since most SNMP
management application uses Public and Private as their default
community name, this might be the leakage of the network security.

105
4.9.2 SNMP V3 Profile
SNMP v3 can provide more security functions when the user performs
remote management through SNMP protocol. It delivers SNMP information
to the administrator with user authentication; all of data between JetNet
Managed Switch and the administrator are encrypted to ensure secure
communication.

Security Level: Here the user can select the following levels of security:
None, User Authentication, and Authentication with privacy.
Authentication Protocol: Here the user can select either MD5
(Message-Digest algorithm 5) or SHA (Secure Hash Algorithm). MD5 is a
widely used cryptographic hash function with a 128-bit hash value. SHA
(Secure Hash Algorithm) hash functions refer to five Federal Information
Processing Standard-approved algorithms for computing a condensed
digital representation. JetNet Managed Switch provides 2 user
authentication protocols in MD5 and SHA. You will need to configure SNMP
v3 parameters for your SNMP viewer with the same authentication method.

Authentication Password: Here the user enters the SNMP v3 user

authentication password.
DES Encryption Password: Here the user enters the password for SNMP
v3 user DES Encryption.

106
4.9.3 SNMP Traps
SNMP Trap is the notification feature defined by SNMP protocol. All the
SNMP management applications can understand such trap information. So
you don’t need to install new application to read the notification information.
This page allows users to Enable SNMP Trap, configure the SNMP Trap
server IP, Community name, and trap Version V1 or V2. After
configuration, you can see the change of the SNMP pre-defined standard
traps and Korenix pre-defined traps. The pre-defined traps can be found in
Korenix private MIB.

4.9.4 CLI Commands of the SNMP

Command Lines of the SNMP configuration

Feature Command Line

SNMP Community
Read Only Community Switch(config)# snmp-server community public ro
community string add ok
Read Write Community Switch(config)# snmp-server community private rw

107
 community string add ok
SNMP Trap
Enable Trap Switch(config)# snmp-server enable trap
Set SNMP trap enable ok.
SNMP Trap Server IP Switch(config)# snmp-server host 192.168.10.33
without specific SNMP trap host add OK.
community name
SNMP Trap Server IP Switch(config)# snmp-server host 192.168.10.33 version 1
with version 1 and private
community SNMP trap host add OK.
Note: private is the community name, version 1 is the
SNMP version
SNMP Trap Server IP Switch(config)# snmp-server host 192.168.10.33 version 2
with version 2 and private
community SNMP trap host add OK.
Disable SNMP Trap Switch(config)# no snmp-server enable trap
Set SNMP trap disable ok.
Display Switch# sh snmp-server trap
SNMP trap: Enabled
SNMP trap community: public

Switch# show running-config

.......
snmp-server community public ro
snmp-server community private rw
snmp-server enable trap
snmp-server host 192.168.10.33 version 2 admin
snmp-server host 192.168.10.33 version 1 admin
……..

108
4.10 Security
JetNet 4508 / 4508f provides several security features for you to secure
your connection. The features include Port Security and IP Security.
Following commands are included in this group:
4.10.1 Port Security
4.10.2 IP Security
4.10.3 IEEE 802.1x
4.10.4 CLI Commands of the Security

4.10.1 Port Security

Port Security feature allows you to stop the MAC address learning for
specific port. After stopping MAC learning, only the MAC address listed in
Port Security List can access the switch and transmit/receive traffic. This is
a simple way to secure your network environment and not to be accessed
by hackers.
This page allows you to enable Port Security and configure Port Security
entry.
Port Security State: Change Port Security State of the port to enable first.
Add Port Security Entry: Select the port, and type VID and MAC address.
Format of the MAC address is xxxx.xxxx.xxxx. Ex: 0012.7701.0101. Max
volume of one port is 10. So the system can accept 100 Port Security MAC
addresses in total.
Port Security List: This table shows you those enabled port security
entries. You can click on Remove to delete the entry.

Sample of JetNet 5010G

109
 Once you finish configuring the settings, click on Apply / Add to apply your
configuration.

4.10.2 IP Security
In IP Security section, you can set up specific IP addresses to grant
authorization for management access to this JetNet via a web browser or
Telnet.
IP Security: Select Enable and Apply to enable IP security function.
Add Security IP: You can assign specific IP addresses, and then press
Add. Only these IP addresses can access and manage JetNet via a web
browser or Telnet. Max security IP is 10.
Security IP List: This table shows you added security IP addresses. You
can press Remove to delete, Reload to reload the table.

Once you finish configuring the settings, click on Apply to apply your
configuration.

110
4.10.3 IEEE 802.1x
4.10.3.1 802.1X configuration
IEEE 802.1X is the protocol that performing authentication to obtain access
to IEEE 802 LANs. It is port-base network access control. With the function,
JetNet 4508 / 4508f could control which connection is available or not.

System AuthControl: To enable or disable the 802.1x authentication.

Authentication Method: Radius is an authentication server that provide
key for authentication, with this method, user must connect switch to server.
If user select Local for the authentication method, switch use the local user
data base which can be create in this page for authentication.
Radius Server IP: The IP address of Radius server
Shared Key: the password for communicate between switch and Radius-
Server.
Server Port: UDP port of Radius server.
Accounting Port: Port for packets that contain the information of account
login or logout.
Secondary Radius Server IP: Secondary Radius Server could be set in
case of the primary radius server down.
802.1X Local User: Here User can add Account/Password for local
authentication.
802.1X Local user List: This is a list shows the account information, User
also can remove selected account Here.

111
4.10.3.2 802.1x Port Configuration
After the configuration of Radius Server or Local user list, user also
need configure the authentication mode, authentication behavior, applied
VLAN for each port and permitted communication. The following
information will explain the port configuration.

Port control: Force Authorized means this port is authorized; the data is
free to in/out. Force unauthorized just opposite, the port is blocked. If users
want to control this port with Radius Server, please select Auto for port
control.
Reauthentication: If enable this field, switch will ask client to
re-authenticate. The default time interval is 3600 seconds.
Max Request: the maximum times that the switch allow client request.
Guest VLAN: 0 to 4094 is available for this field. If this field is set to 0, that
means the port is blocked after authentication fail. Otherwise, the port will
be set to Guest VLAN.
Host Mode: if there are more than one device connected to this port, set
the Host Mode to single means only the first PC authenticate success can
access this port. If this port is set to multi, all the devices can access this
port once any one of them pass the authentication.
Control Direction: determined devices can end data out only or both send and receive.

112
 Re-Auth Period: control the Re-authentication time interval, available
number is 1~65535.
Quiet Period: When authentication failed, Switch will wait for a period and
try to communicate with radius server again.
Tx period: the time interval of authentication request.
Supplicant Timeout: the timeout for the client authenticating
Sever Timeout: The timeout for server response for authenticating.

Once you finish configuring the settings, click on Apply to apply your
configuration.
Click Initialize Selected to set the authorize state of selected port to
initialize status.
Click Reauthenticate Selected to send EAP Request to supplicant to
request reauthentication.
Click Default Selected to reset the configurable 802.1x parameters of
selected port to the default values.

4.10.3.3 802.1X Port Status

Here user can observe the port status for Port control status, Authorize
Status, Authorized Supplicant and Oper Control Direction each port.

4.10.4 CLI Commands of the Security

Command Lines of the Security configuration

Feature Command Line

Port Security
Add MAC Switch(config)# mac-address-table static 0012.7701.0101 vlan 1
interface fa1
mac-address-table unicast static set ok!

113
Port Security Switch(config)# interface fa1
Switch(config-if)# switchport port-security
Disables new MAC addresses learning and aging activities!

Note: Rule: Add the static MAC, VLAN and Port binding first,
then enable the port security to stop new MAC learning.
Disable Port Security Switch(config-if)# no switchport port-security
Enable new MAC addresses learning and aging activities!
Display Switch# show mac-address-table static
Destination Address Address Type Vlan
Destination Port
------------------- --------------- ------- ------------------------
0012.7701.0101 Static 1 fa1
IP Security
IP Security Switch(config)# ip security
Set ip security enable ok.
Switch(config)# ip security host 192.168.10.33
Add ip security host 192.168.10.33 ok.
Display Switch# show ip security
ip security is enabled
ip security host:
192.168.10.33
802.1x
enable Switch(config)# dot1x system-auth-control
Switch(config)#
diable Switch(config)# no dot1x system-auth-control
Switch(config)#
authentic-method Switch(config)# dot1x authentic-method
local Use the local username database for authentication
radius Use the Remote Authentication Dial-In User
Service (RADIUS) servers for authentication
Switch(config)# dot1x authentic-method radius
Switch(config)#
radius server-ip Switch(config)# dot1x radius
Switch(config)# dot1x radius server-ip 192.168.10.120 key
1234

RADIUS Server Port number NOT given. (default=1812)

RADIUS Accounting Port number NOT given. (default=1813)
RADIUS Server IP : 192.168.10.120
RADIUS Server Key : 1234
RADIUS Server Port : 1812
RADIUS Accounting Port : 1813
Switch(config)#
radius server-ip Switch(config)# dot1x radius
Switch(config)# dot1x radius server-ip 192.168.10.120 key
1234

RADIUS Server Port number NOT given. (default=1812)

RADIUS Accounting Port number NOT given. (default=1813)
RADIUS Server IP : 192.168.10.120
RADIUS Server Key : 1234
RADIUS Server Port : 1812
RADIUS Accounting Port : 1813
Switch(config)#

114
radius Switch(config)# dot1x radius secondary-server-ip
secondary-server-ip 192.168.10.250 key 5678

Port number NOT given. (default=1812)

RADIUS Accounting Port number NOT given. (default=1813)
Secondary RADIUS Server IP : 192.168.10.250
Secondary RADIUS Server Key : 5678
Secondary RADIUS Server Port : 1812
Secondary RADIUS Accounting Port : 1813
User name/password Switch(config)# dot1x username korenix passwd korenix vlan
for authentication 1

115
 4.11 Warning
JetNet 4508/4508f provides several types of Warning features for you to
remote monitor the status of end devices or the change of your network.
The features include Fault Relay, System Log and SMTP E-mail Alert.
Following commands are included in this group:
4.11.1 Fault Relay
4.11.2 Event Selection
4.11.3 Syslog Configuration
4.11.4 SMTP Configuration
4.11.5 CLI Commands

4.11.1 Fault Relay

The JetNet 4508 and JetNet 4508f provides 1 alarm relay output , also
known as Digital Output. The relay (DO) contact is energized from normal
and will form a close circuit under system fault conditions.The fault
conditions include power failure, Ethernet port link fault, Ring topology
change, Ping Failure, DI state change or ping remote IP address failure.
From the firmware version 1.1a, the fault relay supports multiple event relay
binding function. That means fault realy not only support one event only, it
can be assigned multiple event. The condition or term described as
following.

Term conditction description

Power DC1
Detect power input status. If one of
Power Power DC2
condiction occurred, relay triggered.
Any
Port Link Port number Monitoring port link down event
Ring Ring failure If ring topology changed
IP Address: remote device’s IP If target IP does not reply ping request, then
Ping
address. relay active.
Ping target device and trigger relay to
IP address: remote device’s address emulate power reset for remote device, if
Ping Reset Reset Time: duration of output open. remote system crash.
Hodl Time: duration of Ping hold time. Note: once perform Ping reset, the relay
output will form a short circuit.
On period: duration of relay output
short (close). Relay continuous perform On/Off behavior
Dry Output
Off period: duration of relay output with different duration.
open.

116
 DI number Relay trigger when DI states change to Hi
DI
(JetNet 4508 supports 1 DI) or Low

The Fault relay configuration UI has shown as below:

Relay 1: Show current relay state

On Period (Sec): Type the period time to turn on Relay Output. Available
range of a period is 0-65535 second seconds.
Off Period (Sec): Type the period time to turn off Relay Output. Available
range of a period is 0-65535 seconds.
Hold Time (Sec): Type the hold time to halts the ping packet.

117
4.11.2 Event Selection
Event Types can be divided into two basic groups: System Events and Port
Events. System Events are related to the overall function of the switch,
whereas Port Events related to the activity of specific ports

System Event Warning Event is sent when…..

Device Cold Start Power is cut off and then reconnected.
Device Warm Start Reboot the device by CLI or Web UI.
Power 1 Failure Power 1 is failure.
Power 2 Failure Power 2 is failure.
Authentication failure An incorrect password, SNMP Community String is
entered.
Time Synchronize Accessing to NTP Server is failure.
Failure
Fault Relay The DO/Fault Relay is on.
Super Ring Topology Master of Super Ring has changed or backup path is
Changes activated.
DI1 Change The Digital Input#1 status is changed.
Port Event Warning Event is sent when…..
Link-Up The port is connected to another device
Link-Down The port is disconnected (e.g. the cable is pulled out,
or the opposing devices turns down)
Both The link status changed.

118
 Sample of JetNet 5010G

Once you finish configuring the settings, click on Apply to apply your
configuration.

4.11.3 SysLog Configuration

System Log is useful to provide system administrator locally or remotely
monitor switch events history. There are 2 System Log modes provided by
JetNet 4508 / 4508f, local mode and remote mode.
Local Mode: In this mode, JetNet 4508 / 4508f will print the occurred
events selected in the Event Selection page to System Log table of JetNet
Managed Switch. You can monitor the system logs in [Monitor and Diag] /
[Event Log] page.
Remote Mode: The remote mode is also known as Server mode in JetNet
series. In this mode, you should assign the IP address of the System Log
server. JetNet 4508 / 4508f will send the occurred events selected in Event
Selection page to System Log server you assigned.
Both: Above 2 modes can be enabled at the same time.

119
 Once you finish configuring the settings, click on Apply to apply your
configuration.

Note: When enabling Local or Both modes, you can monitor the system
logs in [Monitor and Diag] / [Event Log] page.

4.11.4 SMTP Configuration

JetNet 4508 / 4508f supports E-mail Warning feature. The switch will send
the occurred events to remote E-mail server. The receiver can then receive
notification by E-mail. The E-mail warning is conformed to SMTP standard.
This page allows you to enable E-mail Alert, assign the SMTP Server IP,
Sender E-mail, and Receiver E-mail. If SMTP server requests you to
authorize first, you can also set up the username and password in this
page.

120
 Field Description
SMTP Server IP Address Enter the IP address of the email Server
Authentication Click on check box to enable password
User Name Enter email Account name (Max.40 characters)
Password Enter the password of the email account
Confirm Password Re-type the password of the email account
You can set up to 4 email addresses to receive email alarm from JetNet
Rcpt E-mail Address 1 The first email address to receive email alert from
JetNet (Max. 40 characters)
Rcpt E-mail Address 2 The second email address to receive email alert from
JetNet (Max. 40 characters)
Rcpt E-mail Address 3 The third email address to receive email alert from
JetNet (Max. 40 characters)
Rcpt E-mail Address 4 The fourth email address to receive email alert from
JetNet (Max. 40 characters)

Once you finish configuring the settings, click on Apply to apply your
configuration.

4.11.5 CLI Commands

Command Lines of the Warning configuration

Feature Command Line

Relay Output
Relay Output Switch(config)# relay 1
di DI state
dry dry output
ping ping failure
port port link failure
power power failure
ring super ring failure

Note: Select Relay 1 or 2 first, and then select the event

types.
DI State Switch(config)# relay 1 di
<1-2> DI number
Switch(config)# relay 1 di 1
high high is abnormal
low low is abnormal
Switch(config)# relay 1 di 1 high
Dry Output Switch(config)# relay 1 dry
<0-4294967295> turn on period in second
Switch(config)# relay 1 dry 5
<0-4294967295> turn off period in second

121
 Switch(config)# relay 1 dry 5 5
Ping Failure Switch(config)# relay 1 ping 192.168.10.33
<cr>
reset reset a device
Switch(config)# relay 1 ping 192.168.10.33 reset
<1-65535> reset time
Switch(config)# relay 1 ping 192.168.10.33 reset 60
<0-65535> hold time to retry
Switch(config)# relay 1 ping 192.168.10.33 reset 60 60
Port Link Failure Switch(config)# relay 1 port
PORTLIST port list
Switch(config)# relay 1 port fa1-5
Power Failure Switch(config)# relay 1 power
<1-2> power id
Switch(config)# relay 1 power 1
Switch(config)# relay 1 power 2
Super Ring Failure Switch(config)# relay 1 ring
Disable Relay Switch(config)# no relay
<1-2> relay id
Switch(config)# no relay 1 (Relay_ID: 1 or 2)
<cr>
Display Switch# show relay 1
Relay Output Type : Port Link
Port : 1, 2, 3, 4,
Switch# show relay 2
Relay Output Type : Super Ring

Event Selection
Event Selection Switch(config)# warning-event
coldstart Switch cold start event
warmstart Switch warm start event
linkdown Switch link down event
linkup Switch link up event
all Switch all event
authentication Authentication failure event
di Switch di event
fault-relay Switch fault relay event
power Switch power failure event
super-ring Switch super ring topology change event
time-sync Switch time synchronize event
Ex: Cold Start event Switch(config)# warning-event coldstart
Set cold start event enable ok.
Ex: Link Up event Switch(config)# warning-event linkup
[IFNAME] Interface name, ex: fastethernet1 or fa8
Switch(config)# warning-event linkup fa5
Set fa5 link up event enable ok.
Display Switch# show warning-event
Warning Event:
Cold Start: Enabled
Warm Start: Disabled
Authentication Failure: Disabled
Link Down: fa4-5
Link Up: fa4-5
Power Failure:
Super Ring Topology Change: Disabled
Fault Relay: Disabled
Time synchronize Failure: Disable

122
 DI:DI1
Syslog Configuration
Local Mode Switch(config)# log syslog local
Server Mode Switch(config)# log syslog remote 192.168.10.33
Both Switch(config)# log syslog local
Switch(config)# log syslog remote 192.168.10.33
Disable Switch(config)# no log syslog local
SMTP Configuration
SMTP Enable Switch(config)# smtp-server enable email-alert
SMTP Email Alert set enable ok.
Sender mail Switch(config)# smtp-server server 192.168.10.100
ACCOUNT SMTP server mail account, ex: [email protected]
Switch(config)# smtp-server server 192.168.10.100
[email protected]
SMTP Email Alert set Server: 192.168.10.100, Account:
[email protected] ok.
Receiver mail Switch(config)# smtp-server receipt 1 [email protected]
SMTP Email Alert set receipt 1: [email protected] ok.
Authentication with Switch(config)# smtp-server authentication username admin
username and password admin
password SMTP Email Alert set authentication Username: admin, Password:
admin

Note: You can assign string to username and password.

Disable SMTP Switch(config)# no smtp-server enable email-alert
SMTP Email Alert set disable ok.
Disable Authentication Switch(config)# no smtp-server authentication
SMTP Email Alert set Authentication disable ok.
Dispaly Switch# sh smtp-server
SMTP Email Alert is Enabled
Server: 192.168.10.100, Account: [email protected]
Authentication: Enabled
Username: admin, Password: admin
SMTP Email Alert Receipt:
Receipt 1: [email protected]
Receipt 2:
Receipt 3:
Receipt 4:

123
4.12 Monitor and Diag
JetNet 4508 / 4508f provides several types of features for you to monitor
the status of the switch or diagnostic for you to check the problem when
encountering problems related to the switch. The features include MAC
Address Table, Port Statistics, Port Mirror, Event Log and Ping.
Following commands are included in this group:
4.12.1 MAC Address Table
4.12.2 Port Statistics
4.12.3 Port Mirror
4.12.4 Event Log
4.12.5 Topology Discovery
4.12.5 Ping
4.12.6 CLI Commands of the Monitor and Diag

4.12.1 MAC Address Table

JetNet 4508 / 4508f provides 8K entries in MAC Address Table. In this
page, users can change the Aging time, add Static Unicast MAC Address,
monitor the MAC address or sort them by different packet types and ports.
Click on Apply to change the value.
Aging Time (Sec)
Each switch fabric has limit size to write the learnt MAC address. To save
more entries for new MAC address, the switch fabric will age out non-used
MAC address entry per Aging Time timeout. The default Aging Time is 300
seconds. The Aging Time can be modified in this page.
Static Unicast MAC Address
In some applications, users may need to type in the static Unicast MAC
address to its MAC address table. In this page, you can type MAC Address
(format: xxxx.xxxx.xxxx), select its VID and Port ID, and then click on Add
to add it to MAC Address table.
MAC Address Table
In this MAC Address Table, you can see all the MAC Addresses learnt by
the switch fabric. The packet types include Management Unicast, Static
Unicast, Dynamic Unicast, Static Multicast and Dynamic Multicast. The
table allows users to sort the address by the packet types and port.
Packet Types: Management Unicast means MAC address of the switch.
It belongs to CPU port only. Static Unicast MAC address can be added
and deleted. Dynamic Unicast MAC is MAC address learnt by the switch
Fabric. Static Multicast can be added by CLI and can be deleted by Web
and CLI. Dynamic Multicast will appear after you enabled IGMP and the
switch learnt IGMP report.

124
 Click on Remove to remove the static Unicast/Multicast MAC address.
Click on Reload to refresh the table. New learnt Unicast/Multicast MAC
address will be updated to MAC address table.

(Sample of JetNet 5010G )

4.12.2 Port Statistics

In this page, you can view operation statistics for each port. The statistics
that can be viewed include Link Type, Link State, Rx Good, Rx Bad, Rx
Abort, Tx Good, Tx Bad and Collision. Rx means the received packet while
Tx means the transmitted packets.
Note: If you see many Bad, Abort or Collision counts increased, that may
mean your network cable is not connected well, the network performance of
the port is poor…etc. Please check your network cable, Network Interface
Card of the connected device, the network application, or reallocate the
network traffic…etc.
Click on Clear Selected to reinitialize the counts of the selected ports, and
Clear All to reinitialize the counts of all ports. Click on Reload to refresh the
counts.

125
 (sample of JetNet 5010G)
4.12.3 Port Mirroring

Port mirroring (also called port spanning) is a tool that allows you to mirror
the traffic from one or more ports onto another port, without disrupting the
flow of traffic on the original port. Any traffic that goes into or out of the
Source Port(s) will be duplicated at the Destination Port. This traffic can
then be analyzed at the Destination port using a monitoring device or
application. A network administrator will typically utilize this tool for
diagnostics, debugging, or fending off attacks.
Port Mirror Mode: Select Enable/Disable to enable/disable Port Mirror.
Source Port: This is also known as Monitor Port. These are the ports you
want to monitor. The traffic of all source/monitor ports will be copied to
destination/analysis ports. You can choose a single port, or any
combination of ports, but you can only monitor them in Rx or TX only. Click
on checkbox of the Port ID, RX, Tx or Both to select the source ports.
Destination Port: This is also known as Analysis Port. You can analyze
the traffic of all the monitored ports at this port without affecting the flow of
traffic on the port(s) being monitored. Only one RX/TX of the destination
port can be selected. A network administrator would typically connect a
LAN analyzer or Netxray device to this port.
Once you finish configuring the settings, click on Apply to apply the
settings.

126
 Sample of JetNet 5010G

4.12.4 Event Log

In the 4.10.3, we have introduced System Log feature. When System Log
Local mode is selected, JetNet 4508 / 4508f will record occurred events in
local log table. This page shows this log table. The entry includes the index,
occurred data and time and content of the events.
Click on Clear to clear the entries. Click on Reload to refresh the table.

127
4.12.5 Topology Discovery
JetNet JetNet 4508 / 4508f supports topology discovery or LLDP (IEEE
802.1AB Link Layer Discovery Protocol) function that can help user to
discovery multi-vendor’s network devices on same segment by NMS
system which supports LLDP function, for example Korenix JetView Pro
iNMS; With LLDP function, NMS can easier maintain the topology map,
display port ID, port description, system description, VLAN ID… Once the
link failure, the topology change events can be updated to the NMS as well.
The LLDP Port State can display the neighbor ID and IP leant from the
connected devices.

LLDP: Select Enable/Disable to enable/disable LLDP function.

LLDP Configuration: To configure the related timer of LLDP.
LLDP Timer: the interval time of each LLDP and counts in second; the
valid number is from 5 to 254, default is 30 seconds.

128
LLDP Hold time: The TTL (Time To Live) timer. The LLDP state will be
expired once the LLDP is not received by the hold time. The default is 120
seconds.
Local port: the current port number that linked with neighbor network
device.
Neighbor ID: the MAC address of neighbor device on the same network
segment.
Neighbor IP: the IP address of neighbor device on the same network
segment.
Neighbor VID: the VLAN ID of neighbor device on the same network
segment.

129
4.12.6 Ping Utility
This page provides Ping Utility for users to ping remote device and check
whether the device is alive or not. Type Target IP address of the target
device and click on Start to start the ping. After few seconds, you can see
the result in the Result field.

4.12.7 CLI Commands of the Monitor and Diag

Command Lines of the Monitor and Diag configuration

Feature Command Line

MAC Address Table
Ageing Time Switch(config)# mac-address-table aging-time 350
mac-address-table aging-time set ok!

Note: 350 is the new ageing timeout value.

Add Static Unicast MAC Switch(config)# mac-address-table static 0012.7701.0101
address vlan 1 interface fastethernet7
mac-address-table ucast static set ok!

Note: rule: mac-address-table static MAC_address VLAN

VID interface interface_name
Add Multicast MAC Switch(config)# mac-address-table multicast 0100.5e01.0101
address vlan 1 interface fa6-7
Adds an entry in the multicast table ok!

Note: rule: mac-address-table multicast MAC_address

VLAN VID interface_list interface_name/range
Show MAC Address Switch# show mac-address-table
Table – All types
***** UNICAST MAC ADDRESS *****

130
 Destination Address Address Type Vlan Destination Port
------------------- --------------- ------- ------------------------
000f.b079.ca3b Dynamic 1 fa4
0012.7701.0386 Dynamic 1 fa7
0012.7710.0101 Static 1 fa7
0012.7710.0102 Static 1 fa7
0012.77ff.0100 Management 1

***** MULTICAST MAC ADDRESS *****

Vlan Mac Address COS Status Ports
---- --------------- ---- ------- --------------------------
1 0100.5e40.0800 0 fa6
1 0100.5e7f.fffa 0 fa4,fa6
Show MAC Address Switch# show mac-address-table dynamic
Table – Dynamic Learnt Destination Address Address Type Vlan Destination Port
MAC addresses ------------------- --------------- ------- ------------------------
000f.b079.ca3b Dynamic 1 fa4
0012.7701.0386 Dynamic 1 fa7
Show MAC Address Switch# show mac-address-table multicast
Table – Multicast MAC Vlan Mac Address COS Status Ports
addresses ---- --------------- ---- ------- --------------------------
1 0100.5e40.0800 0 fa6-7
1 0100.5e7f.fffa 0 fa4,fa6-7
Show MAC Address Switch# show mac-address-table static
Table – Static MAC Destination Address Address Type Vlan Destination Port
addresses ------------------- --------------- ------- ------------------------
0012.7710.0101 Static 1 fa7
0012.7710.0102 Static 1 fa7
Show Aging timeout Switch# show mac-address-table aging-time
time the mac-address-table aging-time is 300 sec.
Port Statistics
Port Statistics Switch# show rmon statistics fa4 (select interface)
Interface fastethernet4 is enable connected, which has
Inbound:
Good Octets: 178792, Bad Octets: 0
Unicast: 598, Broadcast: 1764, Multicast: 160
Pause: 0, Undersize: 0, Fragments: 0
Oversize: 0, Jabbers: 0, Disacrds: 0
Filtered: 0, RxError: 0, FCSError: 0
Outbound:
Good Octets: 330500
Unicast: 602, Broadcast: 1, Multicast: 2261
Pause: 0, Deferred: 0, Collisions: 0
SingleCollision: 0, MultipleCollision: 0
ExcessiveCollision: 0, LateCollision: 0
Filtered: 0, FCSError: 0
Number of frames received and transmitted with a length of:
64: 2388, 65to127: 142, 128to255: 11
256to511: 64, 512to1023: 10, 1024toMaxSize: 42
Port Mirroring
Enable Port Mirror Switch(config)# mirror en
Mirror set enable ok.
Disable Port Mirror Switch(config)# mirror disable
Mirror set disable ok.
Select Source Port Switch(config)# mirror source fa1-2
both Received and transmitted traffic
rx Received traffic

131
 tx Transmitted traffic
Switch(config)# mirror source fa1-2 both
Mirror source fa1-2 both set ok.

Note: Select source port list and TX/RX/Both mode.

Select Destination Port Switch(config)# mirror destination fa6 both
Mirror destination fa6 both set ok
Display Switch# show mirror
Mirror Status : Enabled
Ingress Monitor Destination Port : fa6
Egress Monitor Destination Port : fa6
Ingress Source Ports :fa1,fa2,
Egress Source Ports :fa1,fa2,
Event Log
Display Switch# show event-log
<1>Jan 1 02:50:47 snmpd[101]: Event: Link 4 Down.
<2>Jan 1 02:50:50 snmpd[101]: Event: Link 5 Up.
<3>Jan 1 02:50:51 snmpd[101]: Event: Link 5 Down.
<4>Jan 1 02:50:53 snmpd[101]: Event: Link 4 Up.
Ping
Ping IP Switch# ping 192.168.10.33
PING 192.168.10.33 (192.168.10.33): 56 data bytes
64 bytes from 192.168.10.33: icmp_seq=0 ttl=128 time=0.0 ms
64 bytes from 192.168.10.33: icmp_seq=1 ttl=128 time=0.0 ms
64 bytes from 192.168.10.33: icmp_seq=2 ttl=128 time=0.0 ms
64 bytes from 192.168.10.33: icmp_seq=3 ttl=128 time=0.0 ms
64 bytes from 192.168.10.33: icmp_seq=4 ttl=128 time=0.0 ms

--- 192.168.10.33 ping statistics ---

5 packets transmitted, 5 packets received, 0% packet loss
round-trip min/avg/max = 0.0/0.0/0.0 ms

132
4.13 Device Front Panel
Device Front Panel command allows you to see LED status of the switch.
You can see LED and link status of the Power, DO, DI, R.M. and Ports.

Feature Status
Power On: the DC power is on applying
Digital Output On: Dry Relay Output activated and the contact is formed a close
circuit.
Digital Input On: Digital Input is triggered to “High” level.
R.M.(Ring Master) Green on: Ring status normal. Yellow (Amber)on: Ring is abnormal
Fast Ethernet Green on: Port is link up.
Sys Green on: the system is ready for working.

Note: No CLI command for this feature.

133
4.14 Save to Flash
Save Configuration allows you to save any configuration you just made to
the Flash. Powering off the switch without clicking on Save Configuration
will cause loss of new settings. After selecting Save Configuration, click
on Save to Flash to save your new configuration.

Command Lines:

Feature Command Line

Save SWITCH# write
Building Configuration…
[OK]

Switch# copy running-config startup-config

Building Configuration...
[OK]

134
4.15 Logout
The switch provides 2 logout methods. The web connection will be logged
out if you don’t input any command after 30 seconds. The Logout command
allows you to manually logout the web connection. Click on Yes to logout,
No to go back the configuration page.

Command Lines:

Feature Command Line

Logout SWITCH> exit

SWITCH# exit

135
 5 Appendix
5.1 Product Specifications
Technology
Standard IEEE 802.3 10Base-T Ethernet
IEEE 802.3u 100Base-TX Fast Ethernet
IEEE 802.3u 100Base-FX Fast Ethernet (JetNet 4508f)
IEEE 802.3x Flow Control and Back-pressure
IEEE 802.1AB Link Layer Discovery Protocol (LLDP)
IEEE 802.1p Class of Service (CoS)
IEEE 802.1Q VLAN and GVRP
IEEE 802.1Q-in-Q and Private VLAN
IEEE 802.1D-2004 Rapid Spanning Tree Protocol (RSTP)
IEEE 802.1s Multiple Spanning Tree Protocol (MSTP)
IEEE 802.3ad Link Aggregation Protocol (LACP)
IEEE 802.1x Port Based Network Access Protocol
IEEE 1588 Precision Time Protocol (PTP)
System Performance
Switch Technology Store and Forward Technology with 32Gbps Switch Fabric.
System Throughput 26 Mega packets per second, 64 bytes packet size.
14,880 PPS for 10Base-T
148,800 PPS for 100Base-TX (PPS: Packet Per Second)
CPU performance 32 bits ARM-9E running at 180 MHz and performance up to
200MIPS; Embedded hardware based watchdog timer.
System Memory 8M bytes flash ROM, 64M bytes SDRAM.
Transfer packet size 64 bytes to 1522bytes (includes 1522 bytes VLAN Tag).
MAC Address 8K MAC address table.
Packet Buffer 1M bits shared memory for packet buffer.
Transfer performance 14,880pps for Ethernet and 148,800 for Fast Ethernet
Relay Alarm Dry Relay output with 1A /24V DC ability.
Digital Input (DI) One Digital Input with Photo Copular isolation
Digital Hi: DC 11V~30V
Digital Low: DC 10V~0V
System Management
Configuration and Supports 4 configuration and monitoring interfaces: RS-232 serial
monitoring interface console, Telnet, SNMP and Web Browser interface

136
 The RS-232 and Telnet interfaces support Cisco like instructions
System upgrade/Backup Provides TFTP/Web interface for firmware upgrade and
configuration backup, restore
Telnet & Local Console Supports command line interface with Cisco like commands and
maximum 4 sessions; the telnet interface also supports SSH
SNMP Supports v1, v2c, V3 with SNMP trap function, trap station up to 4
and can be manually configured the trap server IP address
SNMP MIB MIBII, Bridge MIB, Ethernet-like MIB, VLAN MIB, IGMP MIB, Korenix
Private MIB
Korenix Utility Supports JetView and JetView Pro with IEEE 802.1AB Link Layer
Discovery Protocol for device finding and link topology discovery
Network Time Protocol Supports NTP protocol with daylight saving function and localize time
sync function.
Management IP Security IP address security to prevent unauthorized access
E-mail Warning 4 receipt E-mail accounts with mail server authentication
System Log Supports both Local or remote Server with authentication
Network Performance
IEEE 802.3x Flow control pause frame supports on 10/100bps with Full Duplex
and Back-pressure supports on 100 / 10Mbps Half Duplex only
Port Configuration Port link Speed, Link mode, current status and enable/disable
Port Trunk IEEE 802.3ad port aggregation and static port trunk; trunk member
up to 8 ports and maximum 4 trunk groups.
VLAN IEEE 802.1Q Tag VLAN with 256 VLAN Entries and provides 2K
GVRP entries
3 VLAN link modes- Trunk, Hybrid and Link access
IEEE 802.1 Q-in-Q Supports Double VLAN Tag function for implementing Metro Network
topologies.
Private VLAN The private VLAN supports isolated port access with the uplink port
in the switch.
Typically, each private VLAN contains many private ports and one
given uplink port; each private port is isolated with each other and
only communicates with the uplink port for the outgoing data and
incoming data to provide client port isolated feature.
Class of Service IEEE 802.1p class of service; per port 4 priority queues.
Traffic Prioritize Supports 4 physical queues, weighted run robin queuing (WRR
8:4:2:1) and Strict Priority scheme, which follows 802.1p COS tag
and IPv4 ToS/ Diffserv information to prioritize the traffic of your
industrial network.

137
IGMP Snooping IGMP Snooping v1/v2 /v3 for multicast filtering and IGMP Query
mode; also support unknown multicasting process forwarding
policies- drop, flooding and forward to router port.
Rate Control Ingress filtering for Broadcast, Multicast, Unknown DA or all packets.
Egress filtering for all packet types.
Port Mirroring Online traffic monitoring on multiple selected ports
Port Security Port security to assign authorized MAC to specific port
DHCP DHCP Client, DHCP Server with IP & MAC Address binding and
DHCP agent (option 82).
IEEE 802.1x with Port based network access control and also supports user
Radius Server authenticate by the radius account, password and key for the radius
Authentication server authentication.
Network Redundancy
Multiple Super Ring New generation Korenix Ring Redundancy Technology, Includes
(MSR) TM
Rapid Super Ring, Rapid Dual Homing, TrunkRing TM, MultiRing TM
and backward compatible with legacy Super Ring TM.
Rapid Dual Homing Multiple uplink paths to one or multiple upper switch
TM
(RDH)
TrunkRing TM Integrate port aggregate function in ring path to get higher
throughput ring architecture
TM
MultiRing Couple or multiple up to 16 Rapid Super Rings, JetNet 4508
supports up to 4 Fast Ethernet Ring in one Switch.
IEEE802.1d IEEE802.1D-2004 Rapid Spanning Tree Protocol. Compatible with
Rapid Spanning Tree Legacy Spanning Tree and IEEE 802.1w
IEEE802.1s Supports multiple RSTP deployed in a VLAN or multiple VLANs.
Multiple Spanning Tree IEEE802.1s MSTP, each MSTP instance can include one or more
VLANs.
Interface
Enclosure Port Fast Ethernet communication port: 8 x RJ-45
RS-232 console interface: RJ-45 connector
DI/DO port: 4-pin removable terminal block
Power port: 4-pin removable terminal block
Cables 10Base-T: 2-pairs UTP/STP Cat. 3, 4, 5 cable, EIA/TIA-568B
100-ohm (100m)
100 Base-TX: 2-pairs UTP/STP Cat. 5 cable, EIA/TIA-568B 100-ohm
(100m)
JetNet 4508f-m: multi-mode, 50~62.5/125um, 2KM
JetNet 4508f-s: single mode, 8~10/125um, 30KM

138
Fiber port JetNet 4508f-m
characteristics Wavelength:1310nm
Tx power: -20dBm ~ -14dBm
Rx sensitivity: -31dBm ~ 0dBm
Link Budget: 11dB
JetNet 4508f-s
Wavelength: 1310nm
Tx power: -15dBm ~ -8 dBm
Rx sensivity: -34dBm ~ 0 dBm
Link Budget:19dB
RS-232 serial interface Supports Cisco like command line interface for out-band
management
System Diagnostic LEDs
System Power status (Green): On ( power is on applying)
Digital Input (Green): On (Digital signal is detected)
Alarm Output (Red): On (Output conductor is formed as a close
circuit)
System (Green): On (the system is ready), Blinking (system is on
firmware upgrade progress)
Ring Status (Green/Yellow): Green on ( Ring status is normal), Green
Blinking ( wrong ring port connected), Yellow on (Ring Fail is
occurred), Yellow blinking (ring path broken occurred at this switch)
Ethernet port Link (Green On) / Activity (Green Blinking)
Power Requirements
System Power Redundant power input with polarity auto reverse protection
Input Range: DC 24V (10~60V DC)
Power System Type: Positive or Negative power source
Power Consumption JetNet 4508: 9 Watts / DC 24V
JetNet 4508f: 10Watts / DC 24V
Mechanical
Installation DIN Rail Mounting or Wall Mounting
Case Aluminum metal case with grade 31 protection
Dimension (mm) 55(W) x 149(H) x 131.2 (D) / with DIN Rail Clip
55(W) x 149(H) x 120.6(D) / without DIN Rail Clip
Weight JetNet 4508: 0.85kg
JetNet 4508f: 0.885Kg
Environmental
Operating Temperature -25~70℃ ( JetNet 4508), -10~70℃ (JetNet 4508f)

139
 -40℃~75 ℃ (JetNet 4508-w / JetNet 4508f-w)
Operating Humidity 0% ~ 90%, non-condensing
Storage Temperature -40℃ ~ 85 ℃
Hi-Pot Insulation AC 1.5KV for all ports and power
Regulatory
Approvals
EMC IEC 61000-6-2, IEC 61000-6-4, EN50121-4
EMI
FCC Class A, CE/ EN55022
Radiation, Conduction
EMS
IEC 61000-4-2, IEC 61000-4-3, IEC 61000-4-4, IEC 61000-4-5, IEC
61000-4-6, IEC 61000-4-8, IEC 61000-4-9
Vibration IEC60068-2-6 Note-2
Shock IEC60068-2-27 Note-2
Free Fall IEC60068-2-32 with package Note-3
Warranty Global 5 years
Note-2: pending
Note-3: Korenix’s internal testing
Note-4: For the latest version specification, please contact your sales window or distributor.

140
5.2 Korenix Private MIB
Korenix provides many standard MIBs for users to configure or monitor
the switch’s configuration by SNMP. But, since some commands can’t be
found in standard MIB, Korenix provides Private MIB to meet up the need.
Compile the private MIB file by your SNMP tool. You can then use it.
Private MIB tree is the same as the web tree. This is easier to understand
and use. If you are not familiar with standard MIB, you can directly use
private MIB to manage /monitor the switch, no need to learn or find where
the OIDs of the commands are MIB can be found in product CD or
downloaded from Korenix Web site with the latest version firmware
release.
The path of the JetNet 4508f is 1.3.6.1.4.1.24062.2.2.18 and JetNet 4508
is 1.3.6.1.4.24062.2.2.17 as figures below.

The JetNet 4508/4508f ‘s private MIB supports various of MIB entries, which
are system basic setting, port configuration, network redundancy, VLAN, traffic
priority,multicasting, snmp, security, system warning, monitoring and
configuration saving. User can monitoring and configures JetNet 4508/JetNet
4508f by SNMP MIB browser tools and through those MIB entries to achieve
remote management.
The Private MIB includes 12 major entries for system configuration and
monitoring as below listing:

System information: read only

Basic Setting MIB entry: read and write
Port Configuration MIB entry: Read and Write
Network redundancy MIB entry: Read and Write
Vlan MIB entry: Read and Write

141
Traffic prioritization MIB entry: Read and Write
Multicast Filtering MIB entry: Read and Write
SNMP MIB entry: Read and write
Security MIB entry: Read and write
Warning MIB entry: Read and write
Monitor and Diag: Read and write
Save MIB entry: write only

5.3 Modbus TCP protocol

The Modbus TCP is very similar to Modbus RTU, but transmists data within
TCP/IP Data packets. It was developed in 1979 for industrial automatic
communication system and have becomes a standard protocol for industrial
communication for the transfer discrete analogi I/O devices or PLC systems. It
defines a simple protocol data unit independent of the underlying data link
layer. The modbus TCP packet includes 3 parts - MBAP header, function code
and data payload, the MBAP header is used on TCP/IP header to identify the
Modbus application Data Unit and provides some differences compared to the
MODBUS RTU application data unit used on serial line. The MBAP header
also includes unit indentifier to recognize and communicate between multiple
independent modbus end units.

The modbus devices communicate using a master (client) /slave (server)

architecture, only one device can initiate transaction and the others respond to
the master/client. The other devices (slave/server) respond by supplying the
requested data to the master/client, or by taking the action requested in the
query. The slave/server can be any peripheral device (DSC unit, PLC unit,
142
Volt/Current Transducer, network communication switch) which process
information and sends the output data to the master using modbus TCP
protocol. Korenix JetNet Switch operating as slave/server devices, while a
typical master/client device is host computer running appropriate application
software, like as SCADA / HMI system. The transction architecture like as the
drawing following.

There are three most common Modbus versions, Modbus ASCII, Modbus RTU
and Modbus TCP. Ethernet based device, Industrial Ethernet Switch for
example, supports Modbus TCP that it can be polled through Ethernet. Thus
the Modbus TCP master can read or write the Modbus registers provided by
the Industrial Ethernet Switch.
The JetNet Managed DIN-Rail Ethernet Switch has implement modbud/TCP
register in the firmware. Those register mapping to some of Ethernet Switchs’
operating information, includes decription, IP address, power status, interface
status, interface information and inbound/outbound packet statistics. With the
register supports, user can read the information through their own Modbus
TCP based progress/ display/ monitor applications and monitor the status of
the switch easily.
The configuration of Modbus/TCP only present in CLI management mode and
the no extra user interface for Web configuration.

5.3.1 Modbus Function Code

The Modbus TCP device uses a subset of the standard Modbus TCP function
code to access device-dependent information. Modbus TCP function code is
defined as below.
FC Name Usage

143
 01 Read Coils Read the state of a digital output
02 Read Input Status Read the state of a digital input
Read holding register in 16-bits register
03 Read Holding Register
format
04 Read Input Registers Read data in 16-bits register format
Write data to force a digital output
05 Write Coil
ON/OFF
06 Write Single Register Write data in 16-bits register format
Write data to force multiple consecutive
15 Force Multiple Coils
coils

The JetNet device supports the function code 04, which name is Read Input
Registers. With this support, the remove SCADA or other Modbus TCP
application can poll the information of the device and monitor the major status
of the switch.

5.3.2 Error Checking

The utilization of the error checking will help eliminate errors caused by noise
in the communication link. In Modbus TCP mode, messages include an
error-checking field that is based on a Cyclical Redundancy Check (CRC)
method. The CRC filed checks the contents of the entire message. It applied
regardless of any parity check method used for the individual BYTE acters of
the message. The CRC value is calculated by the transmitting device, which
appends the CRC to the message. The receiving device recalculates a CRC
during receipt of the message, and compares the calculated value to the actual
value it received in the CRC filed.

5.3.3 Exception Response

If an error occurs, the slave sends an exception response message to master
consisting of the slave address, function code, exception response code and
error check field. In an exception response, the slave sets the high-order bit
(MSB) of the response function code to one. The exception response codes
are listed below.
Code Name Descriptions
01 Illegal Function The message function received is not
allowable action.
02 Illegal Data Address The address referenced in the data field is
not valid.

144
03 Illegal Data Value The value referenced at the addressed
device location is no within range.
04 Slave Device Failure An unrecoverable error occurred while the
slave was attempting to perform the
requested action.
05 Acknowledge The slave has accepted the request and
processing it, but a long duration of time will
be required to do so.
06 Slave Device Busy The slave is engaged in processing a
long-duration program command.
07 Negative The slave cannot perform the program
function received in the query.
Acknowledge
08 Memory Parity Error The slave attempted to read extended
memory, but detected a parity error in the
memory.

5.3.4 Modbus TCP register table

Word Address Data Type Description

System Information
0x0000 16 words Vender Name = “Korenix”
Word 0 Hi byte = ‘K’
Word 0 Lo byte = ‘o’
Word 1 Hi byte = ‘r’
Word 1 Lo byte = ‘e’
Word 2 Hi byte = ‘n’
Word 2 Lo byte = ‘I’
Word 2 Hi byte = ‘x’
Word 2 Lo byte = ‘\0’
(other words = 0)
0x0010 16 words Product Name = "JetNet5828G"
Word 0 Hi byte = ‘J’
Word 0 Lo byte = ‘e’
Word 1 Hi byte = ‘T’
Word 1 Lo byte = ‘N’
Word 2 Hi byte = ‘e’
Word 2 Lo byte = ‘t’
Word 3 Hi byte = ‘5’
Word 3 Lo byte = ‘8’
Word 4 Lo byte = ‘2’
Word 4 Hi byte = ‘8’

145
 Word 5 Lo byte = ‘G’
Word 5 Hi byte = ‘\0’
(other words = 0)
0x0020 128 words SNMP system name (string)
0x00A0 128 words SNMP system location (string)
0x0120 128 words SNMP system contact (string)
0x01A0 32 words SNMP system OID (string)
0x01C0 2 words System uptime (unsigned long)
0x01C2 to 0x01FF 60 words Reserved address space
0x0200 2 words hardware version
0x0202 2 words S/N information
0x0204 2 words CPLD version
0x0206 2 words Boot loader version
0x0208 2 words Firmware Version
Word 0 Hi byte = major
Word 0 Lo byte = minor
Word 1 Hi byte = reserved
Word 1 Lo byte = reserved
0x020A 2 words Firmware Release Date
Firmware was released on 2010-08-11 at 09
o’clock
Word 0 = 0x0B09
Word 1 = 0x0A08
0x020C 3 words Ethernet MAC Address
Ex: MAC = 01-02-03-04-05-06
Word 0 Hi byte = 0x01
Word 0 Lo byte = 0x02
Word 1 Hi byte = 0x03
Word 1 Lo byte = 0x04
Word 2 Hi byte = 0x05
Word 2 Lo byte = 0x06
0x020F to 0x2FF 241 words Reserved address space
0x0300 2 words IP address
Ex: IP = 192.168.10.1
Word 0 Hi byte = 0xC0
Word 0 Lo byte = 0xA8
Word 1 Hi byte = 0x0A
Word 1 Lo byte = 0x01

146
0x0302 2 words Subnet Mask
0x0304 2 words Default Gateway
0x0306 2 words DNS Server
0x0308 to 0x3FF 248 words Reserved address space (IPv6 or others)
0x0400 1 word AC1
0x0000:Off
0x0001:On
0xFFFF: unavailable
0x0401 1 word AC2
0x0000:Off
0x0001:On
0xFFFF: unavailable
0x0402 1 word DC1
0x0000:Off
0x0001:On
0xFFFF: unavailable
0x0403 1 word DC2
0x0000:Off
0x0001:On
0xFFFF: unavailable
0x0404 to 0x040F 12 words Reserved address space
0x0410 1 word DI1
0x0000:Off
0x0001:On
0xFFFF: unavailable
0x0411 1 word DI2
0x0000:Off
0x0001:On
0xFFFF: unavailable
0x0412 1 word DO1
0x0000:Off
0x0001:On
0xFFFF: unavailable
0x0413 1 word DO2
0x0000:Off
0x0001:On
0xFFFF: unavailable
0x0414 to 0x041F 12 words Reserved address space

147
0x0420 1 word RDY
0x0000:Off
0x0001:On
0x0421 1 word RM
0x0000:Off
0x0001:On
0x0422 1 word RF
0x0000:Off
0x0001:On
0x0423 1 word RS

Port Information (32 Ports)

0x1000 to 0x11FF 16 words Port Description
0x1200 to 1 word Administrative Status
0x121F 0x0000: disable
0x0001: enable
0x1220 to 1 word Operating Status
0x123F 0x0000: disable
0x0001: enable
0xFFFF: unavailable
0x1240 to 1 word Duplex
0x125F 0x0000: half
0x0001: full
0x0003: auto (half)
0x0004: auto (full)
0x0005: auto
0xFFFF: unavailable
0x1260 to 1 word Speed
0x127F 0x0001: 10
0x0002: 100
0x0003: 1000
0x0004: 2500
0x0005: 10000
0x0101: auto 10
0x0102: auto 100
0x0103: auto 1000
0x0104: auto 2500
0x0105: auto 10000

148
 0x0100: auto
0xFFFF: unavailable
0x1280 to 1 word Flow Control
0x129F 0x0000: off
0x0001: on
0xFFFF: unavailable
0x12A0 to 1 word Default Port VLAN ID
0x12BF 0x0001-0xFFFF
0x12C0 to 1 word Ingress Filtering
0x12DF 0x0000: disable
0x0001: enable
0x12E0 to 1 word Acceptable Frame Type
0x12FF 0x0000: all
0x0001: tagged frame only
0x1300 to 1 word Port Security
0x131F 0x0000: disable
0x0001: enable
0x1320 to 1 word Auto Negotiation
0x133F 0x0000: disable
0x0001: enable
0xFFFF: unavailable
0x1340 to 1 word Loopback Mode
0x135F 0x0000: none
0x0001: MAC
0x0002: PHY
0xFFFF: unavailable
0x1360 to 1 word STP Status
0x137F 0x0000: disabled
0x0001: blocking
0x0002: listening
0x0003: learning
0x0004: forwarding
0x1380 to 1 word Default CoS Value for untagged packets
0x139F
0x13A0 to 1 word MDIX
0x13BF 0x0000: disable
0x0001: enable
0x0002: auto

149
 0xFFFF: unavailable
0x13C0 to 1 word Medium mode
0x13DF 0x0000: copper
0x0001: fiber
0x0002: none
0xFFFF: unavailable
0x13E0 to 288 words Reserved address space
0x14FF
SFP Information (32 Ports)
0x1500 to 0x151F 1 word SFP Type
0x1520 to 0x153F 1 words Wave length
0x1540 to 0x157F 2 words Distance
0x1580 to 0x167F 8 words Vender
0x1680 to 384 words Reserved address space
0x17FF
SFP DDM Information (32 Ports)
0x1800 to 0x181F 1 words Temperature
0x1820 to 0x185F 2 words Alarm Temperature
0x1860 to 0x187F 1 words Tx power
0x1880 to 0x18BF 2 words Warning Tx power
0x18C0 to 0x18DF 1 words Rx power
0x18E0 to 0x191F 2 words Warning Rx power
0x1920 to 1760 words Reserved address space
0x1FFF
Inbound packet information
0x2000 to 2 words Good Octets
0x203F
0x2040 to 2 words Bad Octets
0x207F
0x2080 to 2 words Unicast
0x20BF
0x20C0 to 2 words Broadcast
0x20FF
0x2100 to 0x213F 2 words Multicast
0x2140 to 2 words Pause
0x217F
0x2180 to 2 words Undersize
0x21BF

150
0x21C0 to 2 words Fragments
0x21FF
0x2200 to 2 words Oversize
0x223F
0x2240 to 2 words Jabbers
0x227F
0x2280 to 2 words Disacrds
0x22BF
0x22C0 to 2 words Filtered frames
0x22FF
0x2300 to 2 words RxError
0x233F
0x2340 to 2 words FCSError
0x237F
0x2380 to 0x23BF 2 words Collisions
0x23C0 to 0x23FF 2 words Dropped Frames
0x2400 to 0x243F 2 words Last Activated SysUpTime
0x2440 to 191 words Reserved address space
0x24FF
Outbound packet information
0x2500 to 2 words Good Octets
0x253F
0x2540 to 2 words Unicast
0x257F
0x2580 to 2 words Broadcast
0x25BF
0x25C0 to 2 words Multicast
0x25FF
0x2600 to 2 words Pause
0x263F
0x2640 to 2 words Deferred
0x267F
0x2680 to 2 words Collisions
0x26BF
0x26C0 to 2 words SingleCollision
0x26FF
0x2700 to 2 words MultipleCollision
0x273F

151
0x2740 to 2 words ExcessiveCollision
0x277F
0x2780 to 2 words LateCollision
0x27BF
0x27C0 to 2 words Filtered
0x27FF
0x2800 to 0x283F 2 words FCSError
0x2840 to 447 words Reserved address space
0x29FF
Number of frames received and transmitted with a length(in octets)
0x2A00 to 2 words 64
0x2A3F
0x2A40 to 2 words 65 to 127
0x2A7F
0x2A80 to 2 words 128 to 255
0x2ABF
0x2AC0 to 2 words 256 to 511
0x2AFF
0x2B00 to 2 words 512 to 1023
0x2B3F
0x2B40 to 2 words 1024 to maximum size
0x2B7F
Note: the modbus TCP client will return 0xFFFF to modbus master when
pulling reserved address.

5.3.5 CLI commands for Modbus TCP

The commands of Modbus TCP are listed as following table.
Feature Command & example
Enable Modbus TCP Switch(config)# modbus enable
Disable Modbus TCP Switch(config)# modbus disable
Set Modbus interval time Switch(config)# modbus idle-timeout
between request <200-10000> Timeout vlaue: 200-10000ms
Switch(config)# modbus idle-timeout 200 Æ set
interval request time out duration to 200ms.
Set modbus TCP master Switch(config)# modbus master
communicate session. <1-20> Max Modbus TCP Master
Switch(config)# modbus master 2 Æ set maximum

152
 modbus master up to 2; maximum support up to 20
modbus communicate sessions.
Set modbus TCP listening Switch(config)# modbus port
port port Listening Port
Switch(config)# modbus port 502 ; default modbus TCP
service port is 502.

153
 5.4 Revision History

Edition Date Modifications

V01 12-Nov,2010 New editting
V02 1-DEC,2010 Change power wiring diagram.
V03 8-DEC,2010 Modify:
1. RS LED description
2. Add explaination for the feature diagram of JN 5010G.
3. update exactly model name
4. Change the power wiring diagram with 10V dc input.
V04 20-DEC,2010 Change RJ-45 /DB-9 Console cable connector Pin assignment.
V1.0 23-Mar-2011 Modify:
1. Add port description for port 7, 8 in the feature.
2. Add limitation for JetNet 4508: port 7, 8 support 100Mbps
Auto-Negotiation only in chapter 4.3.1 Port Control , page
51.
V1.1 22-Aug,2011 Add new features:
1. V1.1 firmware supports multi-language function for Web
User Interface. ( English, simplified Chinese)
2. MSTP ( multiple Spanning Tree ) IEEE 802.1s
3. Private VLAN, IEEE 802.1Q double tag VLAN
4. Add ModBus TCP register table
5. Add ModBus TCP CLI commands
ModBus Dis/Enable, Modbus idle timeout, number of master,
Modbus TCP service port.
6. Change Daylight Saving setting method to week and
monthly basis.
7. Add Verification of Conformity cover for EN50121-4.
V1.11 11-OCT-2011 Add new cli command:
Daylight saving time.
V1.12 29-Nov,2011 Add multiple alarm relay function.
Add more Modbus TCP information: Function code, modbus
introduction, etc.
V1.13 27-Apr. 2012 Adjust model name from JetNet 4508/4508f V2 to JetNet
4508/4508f.

154
5.5 About Korenix
Less Time At Work! Fewer Budget on applications!
The Korenix business idea is to let you spend less time at work and fewer budget on
your applications. Do you really want to go through all the troubles but still end up with
low quality products and lousy services? Definitely not! This is why you need Korenix.
Korenix offers complete product selection that fulfills all your needs for applications. We
provide easier, faster, tailor-made services, and more reliable solutions. In Korenix,
there is no need to compromise. Korenix takes care of everything for you!

Fusion of Outstandings
You can end your searching here. Korenix Technology is your one-stop supply center
for industrial communications and networking products. Korenix Technology is
established by a group of professionals with more than 10 year experience in the arenas
of industrial control, data communications and industrial networking applications.
Korenix Technology is well-positioned to fulfill your needs and demands by providing a
great variety of tailor-made products and services. Korenix’s industrial-grade products
also come with quality services. No more searching, and no more worries. Korenix
Technology stands by you all the way through.

Core Strength---Competitive Price and Quality

With our work experience and in-depth know-how of industrial communications and
networking, Korenix Technology is able to combine Asia’s research / development ability
with competitive production cost and with quality service and support.

Global Sales Strategy

Korenix’s global sales strategy focuses on establishing and developing trustworthy
relationships with value added distributors and channel partners, and assisting OEM
distributors to promote their own brands. Korenix supplies products to match local
market requirements of design, quality, sales, marketing and customer services,
allowing Korenix and distributors to create and enjoy profits together.

Quality Services
KoreCARE--- KoreCARE is Korenix Technology’s global service center, where our
professional staffs are ready to solve your problems at any time and in real-time. All of
Korenix’s products have passed ISO-9000/EMI/CE/FCC/UL certifications, fully satisfying
your demands for product quality under critical industrial environments. Korenix global
service center’s e-mail is [email protected]

5 Years Warranty
Each of Korenix’s product line is designed, produced, and tested with high industrial
standard. Korenix warrants that the Product(s) shall be free from defects in materials
and workmanship for a period of five (5) years from the date of delivery provided that the
Product was properly installed and used. This warranty is voided if defects, malfunctions
or failures of the warranted Product are caused by damage resulting from force measure
(such as floods, fire, etc.), environmental and atmospheric disturbances, other external
forces such as power line disturbances, host computer malfunction, plugging the board
in under power, or incorrect cabling; or the warranted Product is misused, abused, or
operated, altered and repaired in an unauthorized or improper way

Business service : [email protected]

Customer service: [email protected]

155