SCALE

engineering108.com
 SCALES

DIMENSIONS OF LARGE OBJECTS MUST BE REDUCED TO ACCOMMODATE

ON STANDARD SIZE DRAWING SHEET. THIS REDUCTION CREATES A SCALE FOR FULL SIZE SCALE
OF THAT REDUCTION RATIO, WHICH IS GENERALLY A FRACTION.. R.F.=1 OR ( 1:1 )
SUCH A SCALE IS CALLED REDUCING SCALE MEANS DRAWING
& OBJECT ARE OF
AND
SAME SIZE.
THAT RATIO IS CALLED REPRESENTATIVE FACTOR.
Other RFs are described
as
SIMILARLY IN CASE OF TINY OBJECTS DIMENSIONS MUST BE INCREASED 1:10, 1:100,
FOR ABOVE PURPOSE. HENCE THIS SCALE IS CALLED ENLARGING SCALE. 1:1000, 1:1,00,000
HERE THE RATIO CALLED REPRESENTATIVE FACTOR IS MORE THAN UNITY.
USE FOLLOWING FORMULAS FOR THE CALCULATIONS IN THIS TOPIC.

DIMENSION OF DRAWING
A REPRESENTATIVE FACTOR (R.F.) =
DIMENSION OF OBJECT
LENGTH OF DRAWING
=
ACTUAL LENGTH
AREA OF DRAWING
=
V ACTUAL AREA
VOLUME AS PER DRWG.
=3
V ACTUAL VOLUME

B LENGTH OF SCALE = R.F. X MAX. LENGTH TO BE MEASURED.

engineering108.com
 BE FRIENDLY WITH THESE UNITS.

1 KILOMETRE = 10 HECTOMETRES
1 HECTOMETRE= 10 DECAMETRES
1 DECAMETRE = 10 METRES
1 METRE = 10 DECIMETRES
1 DECIMETRE = 10 CENTIMETRES
1 CENTIMETRE = 10 MILIMETRES

TYPES OF SCALES:
1. PLAIN SCALES ( FOR DIMENSIONS UP TO SINGLE DECIMAL)
2. DIAGONAL SCALES ( FOR DIMENSIONS UP TO TWO DECIMALS)
3. VERNIER SCALES ( FOR DIMENSIONS UP TO TWO DECIMALS)
4. SCALE OF CORDS ( FOR MEASURING/CONSTRUCTING ANGLES)

engineering108.com
 PLAIN SCALE:- This type of scale represents two units or a unit and it’s sub-division.

PROBLEM NO.1:- Draw a scale 1 cm = 1m to read decimeters, to measure maximum distance of 6 m.

Show on it a distance of 4 m and 6 dm.

CONSTRUCTION:- DIMENSION OF DRAWING

a) Calculate R.F.=
DIMENSION OF OBJECT PLAIN SCALE
R.F.= 1cm/ 1m = 1/100
Length of scale = R.F. X max. distance
= 1/100 X 600 cm
= 6 cms
b) Draw a line 6 cm long and divide it in 6 equal parts. Each part will represent larger division unit.
c) Sub divide the first part which will represent second unit or fraction of first unit.
d) Place ( 0 ) at the end of first unit. Number the units on right side of Zero and subdivisions
on left-hand side of Zero. Take height of scale 5 to 10 mm for getting a look of scale.
e) After construction of scale mention it’s RF and name of scale as shown.
f) Show the distance 4 m 6 dm on it as shown.

4 M 6 DM

10 0 1 2 3 4 5 METERS
DECIMETERS
R.F. = 1/100
PLANE SCALE SHOWING METERS AND DECIMETERS.
engineering108.com
PROBLEM NO.2:- In a map a 36 km distance is shown by a line 45 cms long. Calculate the R.F. and construct
a plain scale to read kilometers and hectometers, for max. 12 km. Show a distance of 8.3 km on it.

CONSTRUCTION:-
a) Calculate R.F.
R.F.= 45 cm/ 36 km = 45/ 36 . 1000 . 100 = 1/ 80,000 PLAIN SCALE
Length of scale = R.F. max. distance
= 1/ 80000 12 km
= 15 cm
b) Draw a line 15 cm long and divide it in 12 equal parts. Each part will represent larger division unit.
c) Sub divide the first part which will represent second unit or fraction of first unit.
d) Place ( 0 ) at the end of first unit. Number the units on right side of Zero and subdivisions
on left-hand side of Zero. Take height of scale 5 to 10 mm for getting a look of scale.
e) After construction of scale mention it’s RF and name of scale as shown.
f) Show the distance 8.3 km on it as shown.

8KM 3HM

10 5 0 1 2 3 4 5 6 7 8 9 10 11
KILOMETERS
HECTOMETERS
R.F. = 1/80,000
PLANE SCALE SHOWING KILOMETERS AND HECTOMETERS
engineering108.com
 We have seen that the plain scales give only two dimensions, such
as a unit and it’s subunit or it’s fraction.

The diagonal scales give us three successive dimensions DIAGONAL

that is a unit, a subunit and a subdivision of a subunit. SCALE

The principle of construction of a diagonal scale is as follows.

Let the XY in figure be a subunit. X
Y
From Y draw a perpendicular YZ to a suitable height. 10’ 10
Join XZ. Divide YZ in to 10 equal parts. 9’ 9
Draw parallel lines to XY from all these divisions 8
8’
and number them as shown.
7
From geometry we know that similar triangles have 7’
their like sides proportional. 6’ 6

5’ 5
Consider two similar triangles XYZ and 7’ 7Z, 4
4’
we have 7Z / YZ = 7’7 / XY (each part being one unit)
3
Means 7’ 7 = 7 / 10. x X Y = 0.7 XY 3’
:. 2
2’
Similarly 1
1’
1’ – 1 = 0.1 XY
2’ – 2 = 0.2 XY Z
Thus, it is very clear that, the sides of small triangles,
which are parallel to divided lines, become progressively
shorter in length by 0.1 XY.

The solved examples ON NEXT PAGES will

make the principles of diagonal scales clear.
engineering108.com
 PROBLEM NO. 4 : The distance between Delhi and Agra is 200 km.
In a railway map it is represented by a line 5 cm long. Find it’s R.F.
Draw a diagonal scale to show single km. And maximum 600 km.
DIAGONAL
Indicate on it following distances. 1) 222 km 2) 336 km 3) 459 km 4) 569 km SCALE
SOLUTION STEPS: RF = 5 cm / 200 km = 1 / 40, 00, 000
Length of scale = 1 / 40, 00, 000 X 600 X 10 5 = 15 cm
Draw a line 15 cm long. It will represent 600 km.Divide it in six equal parts.( each will represent 100 km.)
Divide first division in ten equal parts. Each will represent 10 km.Draw a line upward from left end and
mark 10 parts on it of any distance. Name those parts 0 to 10 as shown.Join 9 th sub-division of horizontal scale
with 10th division of the vertical divisions. Then draw parallel lines to this line from remaining sub divisions and
complete diagonal scale.
569 km
459 km
336 km
222 km
10
9
8
7
6
KM

5
4
3
2
1
0
KM
100 50
0 100 200 300 400 500 KM
R.F. = 1 / 40,00,000

engineering108.com
DIAGONAL SCALE SHOWING KILOMETERS.
PROBLEM NO.5:. Draw a diagonal scale of R.F. 1: 2.5, showing centimeters
and millimeters and long enough to measure up to 20 centimeters. Show the distance 13.4 cm on it.

SOLUTION STEPS:
R.F. = 1 / 2.5 DIAGONAL
Length of scale = 1 / 2.5 X 20 cm. SCALE
= 8 cm.
1.Draw a line 8 cm long and divide it in to 4 equal parts.
(Each part will represent a length of 5 cm.)
2.Divide the first part into 5 equal divisions.
(Each will show 1 cm.)
3.At the left hand end of the line, draw a vertical line and
on it step-off 10 equal divisions of any length.
4.Complete the scale as explained in previous problems.
Show the distance 13.4 cm on it.

13 .4 CM

10
9
8
7
6
MM

5
4
3
2
1
0
CM 5 4 3 2 1 0 5 10 15 CENTIMETRES

R.F. = 1 / 2.5
DIAGONAL SCALE SHOWING CENTIMETERS.
engineering108.com
 Vernier Scales:
These scales, like diagonal scales , are used to read to a very small unit with great accuracy.
It consists of two parts – a primary scale and a vernier. The primary scale is a plain scale fully
divided into minor divisions.
As it would be difficult to sub-divide the minor divisions in ordinary way, it is done with the help of the vernier.
The graduations on vernier are derived from those on the primary scale.
Figure to the right shows a part of a plain scale in
which length A-O represents 10 cm. If we divide A-O
into ten equal parts, each will be of 1 cm. Now it would B 9.9 7.7 5.5 3.3 1.1 0
not be easy to divide each of these parts into ten equal
divisions to get measurements in millimeters.
A 9 8 7 6 5 4 3 2 1 0
Now if we take a length BO equal to 10 + 1 = 11 such
equal parts, thus representing 11 cm, and divide it into
ten equal divisions, each of these divisions will
represent 11 / 10 – 1.1 cm.

The difference between one part of AO and one

division of BO will be equal 1.1 – 1.0 = 0.1 cm or 1
mm.
This difference is called Least Count of the scale.
Minimum this distance can be measured by this scale.
The upper scale BO is the vernier.The combination of
plain scale and the vernier is vernier scale.
engineering108.com
Example 1:
Draw a vernier scale of RF = 1 / 25 to read centimeters upto Vernier Scale
4 meters and on it, show lengths 2.39 m and 0.91 m

SOLUTION: CONSTRUCTION: ( vernier)

Length of scale = RF X max. Distance Take 11 parts of Dm length and divide it in 10 equal parts.
= 1 / 25 X 4 X 100 Each will show 0.11 m or 1.1 dm or 11 cm and construct a rectangle
= 16 cm Covering these parts of vernier.
CONSTRUCTION: ( Main scale)
Draw a line 16 cm long. TO MEASURE GIVEN LENGTHS:
Divide it in 4 equal parts. (1) For 2.39 m : Subtract 0.99 from 2.39 i.e. 2.39 - .99 = 1.4 m
( each will represent meter ) The distance between 0.99 ( left of Zero) and 1.4 (right of Zero) is 2.39 m
Sub-divide each part in 10 equal parts. (2) For 0.91 m : Subtract 0.11 from 0.91 i.e. 0.91 – 0.11 =0.80 m
( each will represent decimeter ) The distance between 0.11 and 0.80 (both left side of Zero) is 0.91 m
Name those properly.

2.39 m

0.91 m

1.1 .99 .77 .55 .33 .11 0

1.0 .9 .8 .7 .6 .5 .4 .3 .2 .1 0 1 1.4 2 3 METERS

METERS

engineering108.com
 Example 2: A map of size 500cm X 50cm wide represents an area of 6250 sq.Kms.
Construct a vernier scaleto measure kilometers, hectometers and decameters Vernier Scale
and long enough to measure upto 7 km. Indicate on it a) 5.33 km b) 59 decameters.
SOLUTION: CONSTRUCTION: ( Main scale) TO MEASURE GIVEN LENGTHS:
AREA OF DRAWING Draw a line 14 cm long. a) For 5.33 km :
RF = Divide it in 7 equal parts. Subtract 0.33 from 5.33
V ACTUAL AREA
i.e. 5.33 - 0.33 = 5.00
( each will represent km )
= 500 X 50 cm sq. Sub-divide each part in 10 equal parts. The distance between 33 dm
V 6250 km sq. ( left of Zero) and
( each will represent hectometer ) 5.00 (right of Zero) is 5.33 k m
= 2 / 105 Name those properly. (b) For 59 dm :
Subtract 0.99 from 0.59
Length of CONSTRUCTION: ( vernier) i.e. 0.59 – 0.99 = - 0.4 km
scale = RF X max. Distance ( - ve sign means left of Zero)
Take 11 parts of hectometer part length
= 2 / 105 X 7 kms The distance between 99 dm and
and divide it in 10 equal parts. - .4 km is 59 dm
= 14 cm Each will show 1.1 hm m or 11 dm and (both left side of Zero)
Covering in a rectangle complete scale.

59 dm 5.33 km
Decameters
99 77 55 33 11

90 70 50 30 10

10 0 1 2 3 4 5 6
HECTOMETERS
KILOMETERS

engineering108.com
 800 900
700
600 SCALE OF CORDS
500

400

300

200

100

00 A O
0 10 20 30 40 50 60 70 80 90

CONSTRUCTION:
1. DRAW SECTOR OF A CIRCLE OF 900 WITH ‘OA’ RADIUS.
( ‘OA’ ANY CONVINIENT DISTANCE )
2. DIVIDE THIS ANGLE IN NINE EQUAL PARTS OF 10 0 EACH.
3. NAME AS SHOWN FROM END ‘A’ UPWARDS.
4. FROM ‘A’ AS CENTER, WITH CORDS OF EACH ANGLE AS RADIUS
DRAW ARCS DOWNWARDS UP TO ‘AO’ LINE OR IT’S EXTENSION
AND FORM A SCALE WITH PROPER LABELING AS SHOWN.

AS CORD LENGTHS ARE USED TO MEASURE & CONSTRUCT

DIFERENT ANGLES IT IS CALLED SCALE OF CORDS.
engineering108.com
 PROBLEM 1: Construct any triangle and measure it’s angles by using scale of cords.
CONSTRUCTION:
First prepare Scale of Cords for the problem.
800 900
Then construct a triangle of given sides. ( You are supposed to measure angles x, y and z) 700
To measure angle at x: 600
Take O-A distance in compass from cords scale and mark it on lower side of triangle 500
as shown from corner x. Name O & A as shown. Then O as center, O-A radius 400
draw an arc upto upper adjacent side.Name the point B.
Take A-B cord in compass and place on scale of cords from Zero. 300
It will give value of angle at x
To measure angle at y: 200
Repeat same process from O1. Draw arc with radius O1A1. 100
Place Cord A1B1 on scale and get angle at y. A O

0
80 9
To measure angle at z: 00
0 10 20 30 40 50 60 70 80 90
Subtract the SUM of these two angles from 180 0 to get angle at z.
70
60

B1
z
50
0
10

40

B
20

30

SCALE OF CORDS
30

20
40

550 300
10

y x
50

O1 A1 A O
60
70
80
90

Angle at z = 180 – ( 55 + 30 ) = 95 0 engineering108.com

PROBLEM 2: Construct 250 and 1150 angles with a horizontal line , by using scale of cord
CONSTRUCTION:
First prepare Scale of Cords for the problem.
800 900
Then Draw a horizontal line. Mark point O on it. 70 0

To construct 250 angle at O. 600

Take O-A distance in compass from cords scale and mark it on on the line drawn, from O 500
Name O & A as shown. Then O as center, O-A radius draw an arc upward.. 400
Take cord length of 250 angle from scale of cords in compass and
from A cut the arc at point B.Join B with O. The angle AOB is thus 25 0 300
To construct 1150 angle at O.
200
This scale can measure or construct angles upto 900 only directly.
Hence Subtract 1150 from 1800.We get 750 angle , 100
which can be constructed with this scale. A O
Extend previous arc of OA radius and taking cord length of 75 0 in compass cut this arc 00
at B1 with A as center. Join B1 with O. Now angle AOB1 is 750 and angle COB1 is 1150. 0 10 20 30 40 50 60 70 80 90

B B1
SCALE OF CORDS

0
10
0

20
10

30
20

250

40
A O
30

50
750
1150
60
40

70
50

80

C
A O
90
60
70 8

To construct 1150 angle at O.

To construct 250 angle at O.
0 90

engineering108.com
 Thank You

For more tutorials on engineering subjects visit is at engineering108.com

engineering108.com