0% found this document useful (0 votes)
38 views3 pages

ADC VC726 Installation Guide

The installation guide for the Indoor/Outdoor Mini Bullet (ADC-VC726) camera outlines the necessary pre-setup checklist and steps to add the camera to an Alarm.com account. It includes troubleshooting tips for connectivity issues and instructions for resetting the camera to factory defaults if needed. Additional resources for training are also provided.

Uploaded by

rudi
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
38 views3 pages

ADC VC726 Installation Guide

The installation guide for the Indoor/Outdoor Mini Bullet (ADC-VC726) camera outlines the necessary pre-setup checklist and steps to add the camera to an Alarm.com account. It includes troubleshooting tips for connectivity issues and instructions for resetting the camera to factory defaults if needed. Additional resources for training are also provided.

Uploaded by

rudi
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Indoor/Outdoor Mini Bullet (ADC-VC726) - Installation Guide

Pre-setup checklist:
• ADC-VC726 camera (included)
• AC power adapter (required for non-PoE connections)
• Broadband (Cable, DSL or Fiber Optic) Internet connection with router
• A computer or mobile device with Internet access
• An Ethernet / Cat5 cable
• Login and Password for the Alarm.com account to which you will add the camera

Add the camera to an Alarm.com account

Complete these steps prior to installing the camera in its final location.
1. Connect the camera to the router via an Ethernet cable. For more information about connecting video devices
using PoE, see Connect a video device using Power-Over-Ethernet (PoE).
2. If the Ethernet connection does not provide power, connect the camera to the optional AC power adapter (sold
separately) and plug the adapter into a non-switched outlet.
3. Wait a few minutes for the camera to connect to the Internet.
4. Add the video device to the account using either MobileTech, or entering the following web
address: www.alarm.com/addcamera to access the Customer Website.
5. Follow the on-screen instructions to add and set up the video device. For more information about adding a camera
to an account, see Enroll the video device to the customer account.
6. Once the camera is enrolled on the account, power down the camera and install it in its final location using the
included hardware.

https://answers.alarm.com/ADC/Partner/Installation_and_Troubleshooting/Video_Devices/Indoor%2F%2FOutdoor_Mini_Bullet_ADC-VC7
Updated: Wed, 19 Jun 2019 01:30:58 GMT

1
Troubleshooting

If you have issues connecting the camera to the account, power cycle the camera and try again.

If issues persist, reset the camera to factory defaults by following these steps:
1. Disconnect the camera from the power supply.
2. Use the Hex Key to remove the water-tight door on the bottom of the camera and locate the Reset button.
3. Press and hold the Reset button while reconnecting power. Continue to hold the Reset button for 10 seconds.

Questions?

Visit: www.alarm.com/supportcenter

https://answers.alarm.com/ADC/Partner/Installation_and_Troubleshooting/Video_Devices/Indoor%2F%2FOutdoor_Mini_Bullet_ADC-VC7
Updated: Wed, 19 Jun 2019 01:30:58 GMT

2
Additional resources

Enroll in the Video as a Service 201 training course today! For more information on accessing Academy
Training, see How can I access Academy Training?.

https://answers.alarm.com/ADC/Partner/Installation_and_Troubleshooting/Video_Devices/Indoor%2F%2FOutdoor_Mini_Bullet_ADC-VC7
Updated: Wed, 19 Jun 2019 01:30:58 GMT

You might also like