V6.

太空盔耗材⼲燥盒系列使⽤说明书
Creality Space Pi Filament Dryer User Manual
包装清单
Package List

太空盔耗材⼲燥盒x1 电源线x1
Creality Space Pi Filament Dryer x1 Power Cable x1

铁氟⻰管×1 说明书x1
PTFE Tube x1 User Manual x1

1
产品简介
Product Introduction

实时湿度 Real-time Humidity

实时温度
Real-time Temperature

⼲燥温度
Drying Temperature

⼲燥材料
Drying Material

⼲燥时间 (hours)
Drying Time (hours)

设置按键 上调按键 下调按键 ⼯作按键

Setting Up Down Play

温馨提示：
1. 产品在潮湿环境放置后，⾸次开机⼯作可能会产⽣异味或烟雾，属于正常现象。

2. 实时温度及实时湿度仅作为⼲燥盒内部环境参考，不可替代温湿度传感器。

3. 停⽌⼲燥后，由于⻛扇停⽌转动且⼲燥盒内留有余温，短时间湿度数值上升是缓慢的，属正
常情况；开盖后，约在30分钟内能看到湿度数值上升。

Kindly Reminder:
1. When the product is placed in a humid environment, there may be some odor
or smoke in first use, which is normal.
2. The real-time temperature and humidity are only for reference for the
environment inside the dryer, which cannot be a substitute for data given by the
temperature and humidity sensor.
3.After stopping drying, due to the fan ceasing to spin and residual heat
remaining in the dryer, the slow increase in humidity levels shortly afterwards is
normal; upon opening the lid, an increase in humidity levels can be observed
within approximately 30 minutes.

2
产品参数
Product Parameters

产品系列 太空盔耗材⼲燥盒系列
Product Series Creality Space Pi Filament Dryer

适⽤范围 1kg耗材
Scope Of Application 1kg Filament

额定电压 UK/GB/EUR/AUS/BRA/CHL/ARG 220-240V~50/60Hz

Rated Voltage US/JPN 100-120V~50/60Hz

⼯作温度
45~70°C
Working Temperature

⼯作时间
0~48H
Working Time

调节⽅式 触屏调节
Adjustment Mode Touch Control

操作指南
Operation Guide

1.开机 Power On
打开背部电源开关 ⻓按⼯作按键0.5s
Switch on the back power supply Long press “Play” 0.5s

2.关机 Power Off

⻓按⼯作按键0.5s 关闭背部电源开关
Long press “Play” 0.5s Switch off the back power supply

3.切换温度单位 Switch Temperature Units

⻓按设置按键 三⻆图标出现屏幕左侧 单击设置按键直到三⻆图标出现在
“PV”左侧 单击上调按键/下调按键
Long Press “Setting” A triangle icon displayed on the left side of the
screen Click “Setting” till the triangle icon moves to the left of
“PV” Click “Up” / “Down” to switch

3
4.修改⼲燥温度 Modify Drying Temperature
⻓按设置按键 三⻆图标出现屏幕左侧 单击设置按键直到三⻆图标出现在
“SV”左侧 单击上调按键/下调按键
Long Press “Setting” A triangle icon displayed on the left side of the
screen Click “Setting” till the triangle icon moves to the left of
“SV” Click “Up” / “Down” to modify

5.修改⼲燥材料 Change Drying Material

⻓按设置按键 三⻆图标出现屏幕左侧 单击设置按键直到三⻆图标出现在
“Material”左侧 单击上调按键/下调按键
Long Press “Setting” A triangle icon displayed on the left side of the
screen Click “Setting” till the triangle icon moves to the left of
“Material” Click “Up” / “Down” to change

6.修改⼲燥时间 Modify Drying Time

⻓按设置按键 三⻆图标出现屏幕左侧 单击设置按键直到三⻆图标出现在
“Time”左侧 单击上调按键/下调按键
Long Press “Setting” A triangle icon displayed on the left side of the
screen Click “Setting” till the triangle icon moves to the left of
“Time” Click “Up” / “Down” to modify

7.耗材推荐⼲燥温度及时间
Recommended Drying Temperatures For
Different Filaments
Display Material Temperature Time
PLA 50°C 4-8h
PLA-CF 50°C 4-8h
TPU 55°C 4-8h
PP 55°C 4-8h
ABS 65°C 8-12h
ASA 65°C 8-12h
PETG 60°C 4-8h
PETG-CF 60°C 4-8h
PC 65°C 8-12h
PA 65°C ≧12h
PA-CF 65°C ≧12h
PET 60°C 4-8h

当设置⼲燥温度⾼于60°C时，请注意外壳表⾯烫⼿
Please be aware that the outer shell may be hot to touch when the
drying temperature is set above 60°C
4
铁氟⻰管使⽤说明
Instructions For Use Of PTFE Tube

1. 把耗材卷放⼊⼲燥盒内，将耗材丝按照图示⽅向穿过⼲燥盒上⽅的出丝孔。
Place the filament roll into the dryer, and feed the filament through
the filament outlet on the top of the dryer as shown in the diagram.

出丝孔
Filament Outlet

2. 将耗材丝穿进铁氟⻰管直到耗材丝漏出⼀段⻓度，随后将铁氟⻰管前端插
进⼲燥盒上⽅的出丝孔内并保证插⼊⼀定的⻓度。
Thread the filament into the PTFE tube until a length of filament
protrudes, then insert the front end of the PTFE tube into the
filament outlet on the top of the dryer, ensuring a certain length
is inserted.

铁氟⻰管
PTFE Tube

5
安全使⽤注意事项
Attentions For Safe Use

1、产品电源线及插座有损伤或有⽔接触时，切勿使⽤。
Please don’t use this product when its power cord and socket are
damaged or in contact with water.

2、⻓时间不使⽤本产品时，请切断电源，避免发⽣突发性⽕灾。
When not in use for a long time, please power off it to avoid
unexpected fire.

3、请勿在潮湿环境中使⽤本产品。
Please never use this product under wet conditions.

4、请勿让⼉童玩耍本产品。
Please keep this product out of the reach of children.

5、本产品若有故障发⽣时，请先将电源关闭，并将电源插头从插座中拔出，
不可继续使⽤，并与本公司售后服务⼈员联系，切勿⾃⾏更换⾮原⼚零件或⾃
⾏拆卸维修。
In case of any failure, please power off this product and then unplug
it instead of using continuously; then, contact our after-sales service
personnel, rather than replacing its parts with non-original ones or
dismantling it for repair.

6、请按照产品铭牌要求的标准电压进⾏供电，否则会有⼯作异常的可能。
Please supply power according to the standard voltage required on
the product nameplate, otherwise there may be a possibility of
abnormal operation.

售后联系⽅式
After-sales Information

E-mail: [email protected]

6
SHENZHEN CREALITY 3D TECHNOLOGY CO.,LTD.
Official Website: www.creality.com
Business Tel: +86 755-8523 4565 E-mail: [email protected]
Company Address: 18th Floor, JinXiuHongDu Building,
Meilong Road, Xinniu Community, Minzhi Street, Longhua
District, Shenzhen City, China.