Scribd
Upload
304 views

Loop Telecom Configurado

The document provides instructions for configuring a LOOP-E E1 CSU/DSU device. It describes selecting the "O" option from the main menu to access the setup menu. From there it describes selecting the "DTE", "MAP", and "SYSTEM" setup groups and configuring various options like line coding, data rates, and IP addresses. It instructs to press escape after configuring each group and confirm saving changes when prompted. Finally, it describes storing the current configuration by selecting option "V" from the main menu.

Uploaded by

Karol Medrano
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
304 views

Loop Telecom Configurado

The document provides instructions for configuring a LOOP-E E1 CSU/DSU device. It describes selecting the "O" option from the main menu to access the setup menu. From there it describes selecting the "DTE", "MAP", and "SYSTEM" setup groups and configuring various options like line coding, data rates, and IP addresses. It instructs to press escape after configuring each group and confirm saving changes when prompted. Finally, it describes storing the current configuration by selecting option "V" from the main menu.

Uploaded by

Karol Medrano
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
You are on page 1/ 3

Debe hacerse un cable DB9-DB9 uno a uno, ingresar por hyperterminal session 9600 igual que los Router

Cisco, no tiene usuario ni contrasea, ya en el equipo debes igresar la lera "O" te lleva a otro men donde debes ingresar "S" o setup system, all se configura DTE, MAP, y SISTEM, dependiendo los requerimientos. >>SPACE bar to refresh or enter a command ===> oprima space bar LOOP-E E1 CSU/DSU V2.12.01 === Main Menu === DTE1: V.35 DTE2: NO EXIST [DISPLAY] [SETUP] 1 -> 1-Hour Perf./Stat. Report 2 -> 24-Hour Perf./Stat. Report A -> Line Availability C -> System Setup Display D -> System Description H -> Alarm History I -> System Status Q -> Alarm Queue 20:00:37 08/26/2010

[ACCESS] F -> Log Off [CLEAR & O -> Log On [CLEAR &

[CLEAR & RESET] [SETUP] and RESET] menu [SETUP] and RESET] menu

>>SPACE bar to refresh or enter a command ===> oprima O LOOP-E E1 CSU/DSU V2.12.01 === Main Menu === 20:00:37 08/26/2010 DTE1: V.35 DTE2: NO EXIST [DISPLAY] [SETUP] 1 -> 1-Hour Perf./Stat. Report K -> V.54 Setup 2 -> 24-Hour Perf./Stat. Report L -> Loopback Test A -> Line Availability M -> Alarm Setup C -> System Setup Display P -> Password Setup D -> System Description T -> Change Date and Time H -> Alarm History S -> System Setup I -> System Status V -> Store Current Configuration Q -> Alarm Queue R -> Retrieve Last Stored Configuration W -> Send Active DS0-MAP to Far-end N -> Synchronize Far-end System Time G -> Router Port Setup Menu [ACCESS] F -> Log Off [CLEAR & O -> Log On [CLEAR & [SETUP] and RESET] menu [SETUP] and RESET] menu [CLEAR & RESET] U -> Clear Alarm Y -> Clear Performance Data Z -> System Reset B -> Upgrade System Firmware X -> Alarm Cut-off

>>SPACE bar to refresh or enter a command ===>

Oprima s >> Select Type ? *LOCAL escoja local

FAR-END

>> Select Setup Group ? *DTE escoja DTE

MAP

SYSTEM

ESCOGE ESTAS OPCIONES === Local System Setup(DTE) === 20:02:14 08/26/2010 ARROW KEYS: CURSOR MOVE, TAB: ROLL OPTIONS LINE=CODE:HDB3 CRC:ON+E RAI:ON FDL:FDL IDLE:D5 FRAME:ON S-BIT:Sa4 (E1 ) DTE1 =<RATE> <CLOCK> <DATA> <INTERFACE> <RTS> <TTM> (DTE) 64K NORMAL NORMAL V.35 ACTIVE OFF CAS:OFF

<< Press ESC key to return to previous menu >> Dar Esc y decir Y cuando pida salvar > Select Setup Group ? *DTE Esoja MAP ESCOGE ESTAS OPCIONES === Local System Setup(MAP) === ARROW KEYS: CURSOR MOVE, TAB: ROLL OPTIONS DS0-MAP 20:04:25 08/26/2010 MAP SYSTEM

:ACTIVE MAP = MAP1 MAP1=[11111111iiiiiiiiiiiiiiiiiiiiiii] MAP2=[1111111111111111111111111111111] SWITCH TIME = MAP1 00:00-12:00 MAP2 12:00-00:00 (RATE) <MAP1> <MAP2> DTE1: 64K 8: 512K 31:1984K DTE2: 64K 0: 0K 0: 0K

<< Press ESC key to return to previous menu >> Dar Esc y decir Y cuando pida salvar >> Select Setup Group ? DTE Escoge SYSTEM ESCOGE ESTAS OPCIONES === Local System Setup(SYSTEM) === 20:05:29 08/26/2010 ARROW KEYS: CURSOR MOVE, TAB: ROLL OPTIONS [Clock Source Setup] MAST-CLOCK:LINE [Console Port Setup] 2nd-CLOCK:LINE CURR-CLOCK : INTERNAL-CLOCK MAP *SYSTEM

BAUD:9600 DATA:8-Bits STOP:1-Bit PAR:NONE XON-XOFF:OFF INTERF:TERMIAL [System Setup] Device Name : LOOP-E 1500-2S My IP Address : 000.000.000.000 Trap IP Address : 255.255.255.255 [Inband Loopback Timer Setup] Loopback Timer(sec): 00000000 [Frame Relay In-band Setup] DLCI: 100 LMI : ITU CIR : 64 T391: 10 N391: 006 N392: 3 Bc: 64 N393: 4 Be: 64 Community Name: public Subnet Mask : 000.000.000.000 Gateway IP : 000.000.000.000

<< Press ESC key to return to previous menu >> Dar Esc y decir Y cuando pida salvar >> Select Setup Group ? *DTE Esc >> Select Type ? *LOCAL Esc LOOP-E E1 CSU/DSU V2.12.01 === Main Menu === 20:06:46 08/26/2010 DTE1: V.35 DTE2: NO EXIST [DISPLAY] [SETUP] 1 -> 1-Hour Perf./Stat. Report K -> V.54 Setup 2 -> 24-Hour Perf./Stat. Report L -> Loopback Test A -> Line Availability M -> Alarm Setup C -> System Setup Display P -> Password Setup D -> System Description T -> Change Date and Time H -> Alarm History S -> System Setup I -> System Status V -> Store Current Configuration Q -> Alarm Queue R -> Retrieve Last Stored Configuration W -> Send Active DS0-MAP to Far-end N -> Synchronize Far-end System Time G -> Router Port Setup Menu [ACCESS] F -> Log Off [CLEAR & O -> Log On [CLEAR & [SETUP] and RESET] menu [SETUP] and RESET] menu [CLEAR & RESET] U -> Clear Alarm Y -> Clear Performance Data Z -> System Reset B -> Upgrade System Firmware X -> Alarm Cut-off FAR-END MAP SYSTEM

>>SPACE bar to refresh or enter a command ===> Escoge V >> Store Current Configuration ? [Y/N] Y password:loop

You might also like