en Service Manual Coffee Machine

EF 470
EF 471

Essenza
Contents

Preface _____________________________ 3 Electronic control board, wiring diagram -

Japan (100 V / 50-60 Hz) _____________ 23
Main Components __________________ 4 Descaling (1) _______________________ 24
Overview ___________________________ 4 Descaling (2) _______________________ 25
Overview of rating plates ______________ 5 Measuring flow rate _________________ 26
Water circuit _________________________ 6 Checking for leaks and pump
Technical data _______________________ 7 pressure (1) ________________________ 27
Checking for leaks and pump
Operation ___________________________ 8 pressure (2) ________________________ 28
Preparation _________________________ 8 Measuring coffee temperature ________ 29
Fill water system _____________________ 9 Daily care and final cleaning __________ 30
Making coffee ______________________ 10
Empty water system _________________ 11 Spare Parts ________________________ 31
Coffee machine status _______________ 12 Repair accessories __________________ 31
Spare parts EF 470 __________________ 32
Troubleshooting___________________ 13 Spare parts EF 471 __________________ 34
Checking the machine on receipt ______ 13
Notes ______________________________ 36
Repair _____________________________ 15
General disassembly ________________ 15
Replacing thermoblock _______________ 16
Replacing NTC _____________________ 17
Replacing pump ____________________ 18
Replacing electronic control board with
button prints ________________________ 19
Replacing compact brewing unit (CBU) _ 20
Electronic control board, wiring diagram -
Europe (230V / 50 Hz) _______________ 21
Electronic control board, wiring diagram -
USA (UL, 120 V / 60 Hz) _____________ 22

Service Manual EF 470 / EF 471 2 Version 1.1 en

Preface

The purpose of this Service Manual is to

provide the service personnel with all
necessary information with regards to correct
handling, maintenance and repair of the coffee
machines EF 470 and EF 471.

This manual should be used by the

technicians as a valuable aid to guarantee the
permanent readiness for use of the machine.
In order to take full advantage of all the
functions, it is absolutely necessary to follow
the instructions in this manual.

Please keep this manual together with the

corresponding service documentation. This
way you are assured to have the necessary
information.

For fast access to information directly from the

PC or MAC monitor, this manual is also
available on CD-ROM. The required utility
(Adobe Acrobat), also on this CD-ROM, runs
on PC and MAC computers.

Service Manual EF 470 / EF 471 3 Version 1.1 en

Main Components

Overview
1) Closing handle
2) Cover 1
3) Compact brewing unit (CBU)
4) Capsule inlet 5 4 3 2
5) Side panel
6) On/Off button
7) Coffee outlet
8) Coffee button, back lighted 6
9) Container for used capsules
10) Drip grid
11) Drip tray 18
12) Lower chassis
13) Thermoblock TB 2003 7
14) Electronic control board
15) Pump CP4-SP C2 8
16) Water tank connector 10 9
17) Upper chassis
18) Water tank

11

17
12

13 14 15 16

Service Manual EF 470 / EF 471 4 Version 1.1 en

Main Components

Overview of rating plates

The rating plate NESPRESSO Type C90 MAGIMIX M100
- can be found at the underside of the coffee
HOUSEHOLD COFFEE MAKER ref 11238
machine,
120V 1260W
- may be of varying design, depending on 220-240V 1260W 50Hz
60Hz A.C.only Fabriqué en Suisse
the brand, LISTED 39C5 FR.6

- carries the following information:

0042699
MADE IN SWITZERLAND

0042728
• Machine type 0529 0074 7002 6100 018 0529 0064 7105 5100 011
• Voltage and power rating
• Approval seal(s)
• Data matrix Typ: KOENIG Capri 03161 Turmix TX100
• Serial number 220-240V~ 1260W 50Hz TURMIX AG, 8645 Jona, Switzerland

• Bar code (Krups) MADE IN SWITZERLAND 220-240V~ 1260W 50Hz

KOENIG APPARATE AG ZÜRICH 17105 MADE IN SWITZERLAND 17105

Serial number codification

Example: 0529 0074 7002 6100 018

0040133

0040624
0529 0044 7105 1100 014 0529 0084 7005 3100 019
05290 production date: 290th day of year 2005
07 machine partner codification
MADE IN EUROPE TYPE XN 2006
470 machine type 220-240V~ 1260W 50/60Hz
02 voltage / mains plug version Type EN 90.R
6 color version 220-240V~ 50/60Hz 1260W

0040541
1 production site
MADE IN SWITZERLAND
0001 incremental number per production day P = 19 bar

0042829
8 checksum number 0529 0014 7105 1100 011
XN200610/1M0-4205
Ser.Nr. 54213 S300075
0529 0054 7005 6100 019

Service Manual EF 470 / EF 471 5 Version 1.1 en

Main Components

Water circuit
1) Water tank
2) Water tank valve and connector
3) Pump
4) Thermoblock
5) Compact brewing unit (CBU)
6) Coffee outlet
5

6
1

4 3

Service Manual EF 470 / EF 471 6 Version 1.1 en

Main Components

Technical data Mains Power consumption

EUR 230V / 50 Hz (at all voltages and frequencies)
EF 470 USA /CAN 120 V / 60 Hz Thermoblock 1’200 W
mm JAP 100 V / 50-60 Hz Pump 60 W
291

Approvals SEV, CENELEC, CE-conform,

UL, CUL, MITI Ratings
255 mm Preheating 8.5 Wh
Cable length ~1,5 m
1 small cup (55 ml) 6.5 Wh
1 large cup (110 ml) 10 Wh
Stand-by mode 9.5 Wh
Pump data (machine on) (in 1 hour)
Pump pressure Stand-by mode 0.45 Wh
166
mm - max. permissible 17,5 bar ±1,5 bar (machine off) (in 1 hour)
- during coffee preparation 9 -13 bar
(depending on brand of coffee)
EF 471 mm Various data
291
Flow performance 120-240 ml/min. at 12 bar Pre-heating time approx. 50 s

Safety temperature (thermal cut-off) 167° C

254 mm Capacities Coffee temperature at outlet 86° C ± 3° C
Water tank 0.9 l
Drip tray approx. 100 ml Weight of machine approx. 3 kg
Capsule container 10 - 14 pcs. (without water)

166
mm

Service Manual EF 470 / EF 471 7 Version 1.1 en

Operation

Preparation
1. Fill tank with water. 1
2. Insert water tank in coffee machine.
3. Switch on machine by pressing the On/Off
button. 3
4. Position receptacle with a capacity of
min.100 ml under coffee outlet.

) Do not insert a capsule yet.

2
5. Wait until machine is ready (coffee button 4
is lighted).
6. Press coffee button to rinse coffee outlet.
7. Press coffee button again when
receptacle is filled.

5 6 7

Service Manual EF 470 / EF 471 8 Version 1.1 en

Operation

Fill water system

If the coffee machine cannot pump water 2 5 4
although there is water in the tank, the water
circuit may be empty.

Procedure to fill water system:

1. Perform steps 1 to 5 for preparation (see
page 8).
2. Open closing handle in vertical position. 3
3. Press coffee button.
4. Press and hold closing handle to rear end
position.
5. Observe capsule inlet for appearing
water.
6. Press down closing handle immediately
when first droplets are visible.
7. Press coffee button again to stop water 6
flow.

Service Manual EF 470 / EF 471 9 Version 1.1 en

Operation

Making coffee
1 3
1. Open closing handle.
2. Insert capsule.
3. Press down closing handle completely. 2
4. Position cup under coffee outlet.
5. Press coffee button.
6. Press button again to stop coffee flow
when cup is full.
7. Briefly open closing handle after coffee 4 5
preparation and eject capsule into capsule
container.

Service Manual EF 470 / EF 471 10 Version 1.1 en

Operation

Empty water system

5
After operation, residual water remains in the
water circuit.
1
This residual water can be removed
- before a longer period of non-use,
- for frost protection, 2
- before repair and following shipping. 4
3

1. Empty water tank. 3x

2. Press and hold On/Off button.
3. Simultaneously press coffee button three
times.
4. Release On/Off button.
The coffee button starts blinking fast and
the pump begins to empty the water
system. 6
5. Open closing handle and hold it in opened
position.
6. After coffee button stops blinking, press
down closing handle completely.
7. Empty drip tray.
7

) After this procedure the machine is

blocked for approx. 10 minutes (till
thermoblock temperature < 100° C).

Service Manual EF 470 / EF 471 11 Version 1.1 en

Operation

Coffee machine status Operating mode Coffee button LED signal

After pressing the On/Off button, an automatic
Off off
self test is performed to check if
- the NTC is connected,
- the NTC is short circuited, Heat up (coffee) blinking slow
- the thermoblock reaches the standby
temperature within 2 minutes in brewing
mode. Ready on

A detected failure is indicated by the

backlighted coffee button as well as the System too hot blinking fast
operating modes listed in the following table.

Brew coffee / rinse blinking slow

Heat up (descaling) blinking fast

Descaling ready blinking fast

Pump on (while descaling) blinking fast

Emptying water system blinking fast

Failure blinking three times fast

Service Manual EF 470 / EF 471 12 Version 1.1 en

Troubleshooting

Checking the machine on receipt

The receipt check enables you to rapidly Follow the check procedure.
locate faults on the machine and to initiate Repair any faults found and check if the
appropriate repair action. machine is operating perfectly.

Check procedure Symptoms Action / repair work Further action / repair work

YES - Replace parts if necessary

1.1 Parts of housing broken or damaged
1 Check appliance for visible NO - Go to point 1.2
damage YES - Replace mains cable
1.2 Mains cable damaged
NO - Plug machine to the mains and go to point 2.1
YES - Go to point 2.2
YES - Screw on closing handle screws at defined
2.1 Closing handle works correctly torque and block them with Loctite 241 (see page
NO - It is hard or impossible to close the closing handle
20) or replace CBU
2 Check mechanical elements NO - Replace the CBU
YES - Go to point 2.3
2.2 Is the capsule correctly ejected?
NO - Replace CBU
2.3 Is the capsule cage seal damaged? YES - Replace CBU
(feel with a finger if the seal is damaged) NO - Go to point 3
YES - Replace water tank
3 Fill water tank 3.1 Water tank is leaking
NO - Go to point 4
YES - Go to point b)
YES - a) Check if mains cable is functional
NO - Replace it
YES - Go to point c)
YES - b) Check if On/Off button is functional
NO - Replace it
YES - c) Check if pump is working (press coffee YES - Go to point f)
button) NO - Go to point d)
4 Press On/Off button to perform
4.1 Machine is not working (no function) YES - Go to point e)
automatic self test YES - d) Check if coffee button is functional
NO - Replace it
YES - e) Check if pump's fine wire fuse (128°C) is YES - Replace it
defective NO - Replace pump
YES - Replace it together with electronic control
YES - f) Check if thermoblock’s fine wire fuse (167°C)
board and if necessary the thermoblock
is defective
NO - Go to point g)

Service Manual EF 470 / EF 471 13 Version 1.1 en

Troubleshooting

Check procedure Symptoms Action / repair work Further action / repair work

YES - Replace electronic mainboard

4.1 Machine is not working (no function) YES - g) Check if electrical wires are functional
NO - Replace defective(s) wire(s)
- continued
4 Press On/Off button to perform NO - Go to point 4.2
automatic self test - continued YES - Check if thermoblock heating element is func- YES - Replace NTC
4.2 Backlighted coffee button blinks at irregular tional NO - Replace thermoblock
intervals
NO - Self test ok. Go to point 5
YES - Fill water circuit (see page 9)
YES - a) Water circuit is empty
NO - Go to point b)
YES - Replace CBU
5.1 No coffee outlet YES - b) Pyramid plate is clogged
NO - Go to point c)
5 Check coffee temperature while YES - c) Machine is blocked by scale YES - Descale machine (see page 24)
preparing a coffee (see page 29) NO - Go to point 5.2
YES - Descale the machine (see page 24)
5.2 Temperature is too low (less than 83°C)
NO - Go to point 5.3
YES - Change NTC
5.3 Temperature is too high (more than 89°C)
NO - Go to point 6
YES - Replace CBU
6.1 Leakage at extraction system
NO - Go to point 6.2
YES - Replace defective tube and seal
6.2 Leakage at tubes connection
6 Check for leaks and check flow NO - Go to point 6.3
rate (see pages 26, 27 and 28) YES - Descale machine (see page 24)
YES - Machine is scaled
NO - Replace pump
6.3 Flow rate out of range
Contact Nespresso Technical Correspondant for
NO - No trouble found during the check procedure.
further details in order to take decision.
YES - Descale machine (see page 24)
7 Descaling process (if needed) 7.1 Machine scaled
NO - Go to point 8
8 Final cleaning (see page 30)

End of check procedure

Service Manual EF 470 / EF 471 14 Version 1.1 en

Repair

General disassembly

Tool:
- Oval screwdriver

) Empty water system if necessary

(see page 11).
5

 Unplug from the mains before

disassembling machine - appliance
33
must be isolated!

Procedure:
1. Remove water tank (33) and drip tray (8)
together with drip grid (7) and capsule 2
container (6).
2. Remove 2 screws (2) on the front side of 22 2
the machine.
3. Place machine on the repairing/service
holder device (see page 31).
4. Remove 6 screws (2) on the bottom of the
machine.
5 2
5. Swing out and remove both side panels
(5).
6. Remove lower chassis (22).
7+8+6
2

Service Manual EF 470 / EF 471 15 Version 1.1 en

Repair

Replacing thermoblock
Tools:
- Torx screwdrivers T10, T30
- Open-ended spanner 10 mm AF
- Torque wrench
Procedure:
1. Follow general disassembly (see page 15).
2. Remove 3 screws (2) and separate thermo-
block (40) with support (40) from chassis.
3. Remove screw M6 x 25 and separate
thermoblock from its support.
4. Remove screw (38) and separate fine wire
fuse (900) from thermoblock.
5. Remove electronic housing (28).
6. Unplug NTC connector from electronic
control board (28).
7. Remove NTC (43) from thermoblock. 28 M6 x 25
8. Remove clips (13) and hose connectors 38
(16, 26) from thermoblock. 16
9. Remove ground wire and electrical
13 40
connections from thermoblock.
10. Replace thermoblock and nut M6. 26
38
11. Assemble in reverse sequence.
39

)
40
Use a torque wrench (90 - 110 Ncm)
to tighten NTC temperature sensor 2
(43) with spring washer. 900 43

) Check that there is a clearance of

1-2 mm between thermoblock and
support after assemblage.
M6

Service Manual EF 470 / EF 471 16 Version 1.1 en

Repair

Replacing NTC

Tools:
- Torx screwdriver T10
- Open-ended spanner 10 mm AF
- Torque wrench

Procedure:
1. Follow general disassembly (see page 15).
2. Remove electronic housing (28).
3. Unplug NTC connector from electronic
control board (28).
4. Remove defective NTC temperature
sensor (43) from thermoblock (40) and
replace it with new one.
5. Assemble in reverse sequence.

) Re-use spring washer and tighten

new NTC temperature sensor (43)
with torque wrench (90 - 110 Ncm).

28

43
40

Service Manual EF 470 / EF 471 17 Version 1.1 en

Repair

Replacing pump

Tools:
- Torx screwdriver T10
- Long-nose pliers
- Blade screwdriver, no. 7

Procedure:
1. Follow general disassembly (see page 15).
2. Remove clip (14), hose (18) and o-ring
(15).
3. Remove angled hose (9).
4. Release pump (17) first from rubber strap
(12) at the side of the angled hose. 9
12
5. Remove electrical connections from pump.
6. Release pump from second rubber strap N
(12). T 128°C
7. Replace defective pump (17).
8. Attach new pump (17) to one rubber strap
with corner connector (20) first.
9. Plug in electrical connections on pump.
9

) Check for correct wiring of pump.

10. Attach pump to second rubber strap.
18
L 17
11. Insert new seal (15), mount hose (18) and 15
clamp (14).
14
12. Mount angled hose (9).

20

Service Manual EF 470 / EF 471 18 Version 1.1 en

Repair

Replacing electronic control board

with button prints

Tools:
- Torx screwdriver T10

 The service engineer must be

earthed using an earthing strap!

) Only touch button prints with

dedicated gloves to avoid oxydation.

Procedure:
1. Follow general disassembly (see page 15).
2. Detach prints of On/Off button (30) and
coffee button (29) from upper chassis (1).
3. Remove housing (28) from electronic
control board (28).
4. Unplug NTC connector and all wires from
electronic control board (28).
5. Remove 2 screws (23) and replace defect 28
electronic control board with button prints
(29, 30). 1
6. Assemble in reverse sequence. 23

) Check for correct wiring of electronic

control board (see pages 21, 22 or
23).
30

29

Service Manual EF 470 / EF 471 19 Version 1.1 en

Repair

Replacing compact brewing unit (CBU)

33
Tools:
- Torx screwdrivers T10, T20 23
- Blade screwdriver no. 4 2
- Oval screwdriver
- Long-nose pliers
- Torque wrench 36 34
Procedure:
1. Remove water tank (33) and drip tray (8)
35
together with drip grid (7) and capsule
container (6). 23
2. Place machine on the repairing/service 7+8+6 5
holder device (see page 31). 37 15
3. Remove 4 screws (2) on the bottom of the 23 36
14+32
machine.
4. Swing out and remove both side panels (5).
5. Remove 2 screws (36) and pull off closing
handle (37).
23
6. Remove 2 screws (23) at the front and 1
screw (23) at the back to detach cover (35). 3
7. Unlatch coffee outlet (3) from compact
brewing unit (34) with a blade screwdriver.
8. Remove 4 screws (23) and detach
compact brewing unit (34).
9. Remove clip (14) and hose (32) with o-ring
(15) from compact brewing unit (34).
10. Assemble new compact brewing unit
together with new coffee outlet (3) in
reverse sequence.
) Tighten new (EFR nr. 39256) closing
handle screws (36) with a torque of
450 N/cm.
Replace o-ring (15).

Service Manual EF 470 / EF 471 20 Version 1.1 en

Repair

Electronic control board, wiring

diagram - Europe (230V / 50 Hz) Electronic Main Board ON/OFF Print Coffee Button Print
1) Heat sink
2) Print for On/Off button
3) Print for coffee button with LED 1
3
4) NTC temperature sensor 2
5) Fine-wire fuse on thermoblock
6) Fine-wire fuse on pump

J5

J4
J3
Thermoblock
4
J7 J6 J1 J2
NTC T 167°C
5
L L N L
GND

Pump
T 128°C
6
Mains Plug
L N PE

Service Manual EF 470 / EF 471 21 Version 1.1 en

Repair

Electronic control board, wiring

diagram - USA (UL, 120 V / 60 Hz) Electronic Main Board ON/OFF Print Coffee Button Print
1) Heat sink
2) Print for On/Off button
3) Print for coffee button with LED 1
4) NTC temperature sensor 3
2
5) Fine-wire fuse on thermoblock

J5

J4
J3
Thermoblock
4 5
J7 J6 J1 J2
NTC T 167°C

L L N L

Pump
T 128°C

Mains Plug

Service Manual EF 470 / EF 471 22 Version 1.1 en

Repair

Electronic control board, wiring

diagram - Japan (100 V / 50-60 Hz) Electronic Main Board ON/OFF Print Coffee Button Print
1) Heat sink
2) Print for On/Off button
3) Print for coffee button with LED 1
3
4) NTC temperature sensor 2
5) Fine-wire fuse on thermoblock
6) Fine-wire fuse on pump

J5

J4
J3
Thermoblock
4
J7 J6 J1 J2
NTC T 167°C
5
L L N L

Pump
T 128°C
6
Mains Plug
L N

Service Manual EF 470 / EF 471 23 Version 1.1 en

Repair

Descaling (1)
2
 Only use Nespresso decalcifier -
never vinegar!
Decalcifier is aggressive to surfaces.

Preparation:
1. Switch off machine. 3
2. Eject capsule. Insert filter from descaling 1
kit in capsule inlet and close handle.
3. Empty drip tray and capsule container and
remove drip grid.
4. Re-insert drip tray and place a pot on it.

) Carefully read safety instructions on

decalcifier package.
5. Fill water tank with 0.1 l descaling fluid
5
and 0.5 l water. Re-insert water tank.
6. Press On/Off button and coffee button
simultaneously for at least 3 seconds to
switch on machine and start descaling
mode (fast blinking coffee button).
6
Descaling: 4
7. Press coffee button to start pump. 8 6 7
8. Let entire descaling solution pass through
coffee outlet.

Service Manual EF 470 / EF 471 24 Version 1.1 en

Repair

Descaling (2)
9. Fill water tank again with descaling 12
solution from pot.
9
10. Repeat descaling procedure one more
time: Press coffee button and let entire
descaling solution run through.

Rinsing:
11. Empty pot.
12. Remove filter from capsule inlet. 11
10
13. Rinse water tank thoroughly and fill it with
fresh water.
14. Place pot on drip tray.
15. Press coffee button to start pump.
Let complete content of water tank run
through coffee outlet.
16. Switch off machine. 18
Descaling is completed. 13
17. Insert drip grid.
18. Clean machine.
16
17

14 15

Service Manual EF 470 / EF 471 25 Version 1.1 en

Repair

Measuring flow rate

2
Procedure: 1
1. Fill water tank.
2. Insert pressure plug in capsule inlet. 3
3. Press down closing handle lightly till
pressure plug fits in capsule cage.
4. Pull off holding device. The pressure plug
clamps itself to the capsule cage.
5. Position measuring beaker underneath
exit tube of pressure plug.
6. Switch on machine. Press coffee button
after heating-up.
7. Open valve fully till water begins to flow.
8. Close valve until 12 bar are indicated.

) The manometer must be observed

continuously and the pressure
regulated using the valve if
Notice:
- With a flow of < 60 ml the pump is defective
4
or there is a leak in the system.
necessary. With increasing
- Large fluctuations in the pressure gauge
temperature the pressure also
readings (± 4 bar) during measurement are 7
increases, if necessary readjust the
indicative of a defective pump.
pressure to 12 bar.
9. Perform measurement for approx. 30 sec.
10. There must be at least 60-120 ml water in 8 6
the measuring beaker.
6

Service Manual EF 470 / EF 471 26 Version 1.1 en

Repair

Checking for leaks and pump

pressure (1)
The following components are checked for 2 4
leaks: 3
- Compact brewing unit
- Connections
- Thermoblock
- Pump

Preparation (unplug machine from mains):

1. Remove right side panel (pump is visible).
2. Insert pressure plug in capsule inlet.
3. Press down closing handle lightly till 1
pressure plug fits in capsule cage.
4. Pull off holding device. The pressure plug
clamps itself to the capsule cage.
5. Position pot underneath exit tube of 6
pressure plug.
6. Fill water tank.
7. Connect mains cable.

 Dangerous voltage inside coffee

machine! - Do not touch any live part
while performing checks.
Hot, pressurized parts inside coffee
machine! - Do not touch any hot part 7
while performing checks. Wear
safety glasses during inspection. 5

Continued on next page.

Service Manual EF 470 / EF 471 27 Version 1.1 en

Repair

Checking for leaks and pump

pressure (2) 9

Procedure (continued):
8. Switch on machine. Press coffee button
after heating-up. 10
9. Open valve and leave water to run out for
approx. 10 s. 8
10. Fully close valve. The pressure will rise
rapidly initially and stabilise between 8
16 - 19 bar (check of pump pressure).

) The pressure will rise slowly due to

the temperature increase.
If the pressure exceeds 23 bar, the
machine has to be switched off and
pressure released through the
pressure valve.
11. Perform visual and acoustic checks on all
pressurized connections. 13

 The pump must not be in operation

for longer than 50 s without water
flow.
12
12. Switch off machine. 11
13. Open valve to empty pressure gauge.

Service Manual EF 470 / EF 471 28 Version 1.1 en

Repair

Measuring coffee temperature

Procedure:
1. Press On/Off button to switch on machine.
2. Position measuring beaker underneath 1
coffee outlet.
3. After warming up, press coffee button and
preheat coffee outlet for 10 s with hot 3
water.
4. Insert a capsule (Cosi is the most suitable).
5. Press coffee button.
2
6. Wait until 20 ml coffee has flown in the
measuring beaker.
7. Measure the coffee temperature approx.
5 - 10 mm below the outlet opening.

) Coffee temperature should be

approx. 86 °C ± 3 °C (187 °F ± 5.4 °F). 4

5
6

Service Manual EF 470 / EF 471 29 Version 1.1 en

Repair

Daily care and final cleaning

1
Procedure: 2
1. Eject capsule.
2) Empty capsule container.
3) Empty water tank and drip tray.
4) Clean water tank and drip tray.
5) Fill tank with fresh water.
6) Reassemble coffe machine.
7) Press On/Off button.
8) Press coffee button and rinse coffe outlet
for 10 s.
9. Clean coffee machine.

5
7 9

4
8

Service Manual EF 470 / EF 471 30 Version 1.1 en

Spare Parts

Repair accessories

Pos. EFR nr. Component

1 * Pressure gauge
2 * Repairing/service holder device A (for EF 470)
2 * Repairing/service holder device B (for EF 471)
3 0004872 Special screwdriver with oval bit
4 0004878 Oval bit for screwdriver

* Only available through Nespresso. Please contact the Nespresso club.

1

0004878

0004872

Service Manual EF 470 / EF 471 31 Version 1.1 en

Spare Parts

Spare parts EF 470 Pos. EFR nr. Component

1 39166 Upper chassis EF 470
3 3 2 1 36 37 36 2 24863 Safety screw 3,0 x 12 KST/PT
23
3 40686 Coffee outlet & front ring EF 470 (package)
5 39378 Side panel EF 470 titanium
35
5 39148 Side panel EF 470 ivory
23
5 42614 Side panel EF 470 orange
34
6 39170 Capsule container EF 470
33 7 39150 Drip grid EF 470
23 8 40477 Drip tray EF 470 printed : "Turmix"
5 15 8 40478 Drip tray EF 470 printed : "Krups"
32 8 40479 Drip tray EF 470 printed : "Nespresso"
9 39197 Hose water tank / pump
14
6 10 40691 Water tank connector assembled
31
11 39195 Pump attachment
30 12 39196 Pump fixation
29 13 37384 Clip D=5mm
7 14 5470 Clip to tube 770
15 24374 O-ring 3,4 x 1,9 silicon
8
16 37454 Angle connection for hoses
9 17 41029 Pump 230V
10
38 17 42530 Pump 120V
38 17 41030 Pump 100V
39
11
18 39199 Hose pump / thermoblock
12 5 19 1565 O-ring 5,28 x 1,78 EPDM
13
14 28 20 36613 Angle connection for pump
23 21 13299 Elastic stop
15
16
27 22 39164 Lower chassis EF 470
15
15 23 16052 Screw 3,0 x 12 Torx 10
14 24 1053 Strain relief screwed
17
26 25 39369 Power cord Cebec 1,3m
11
13 25 39266 Power cord SEV 1,3m
18
15 25 40535 Power cord Israel 1,3m
12 15 19 14 20 21 2 40 22 2 21 23 24 41 42 43 25
25 39368 Power cord GB 1,3m

Service Manual EF 470 / EF 471 32 Version 1.1 en

Spare Parts

Spare parts EF 470 (continued) Pos. EFR nr. Component

25 42135 Power cord UL1,3m
3 3 2 1 36 37 36 25 39271 Power cord Japan1,3m
23
26 38412 Angle connection for hoses
27 39188 Electronic base
35
28 40688 Electronic set 230V
23
28 40689 Electronic set 120V
34
28 40690 Electronic set 100V
33 29 39153 "Coffee" button EF 470
23 30 39152 "ON-OFF" button EF 470
5 15 31 26392 Silicon hose
32 32 39198 Hose thermoblock / CBU
33 39142 Water tank EF 470
14
6 34 40685 Compact brewing unit (CBU)
31
35 39168 Cover EF 470
30 36 39256 Screw M4 x 25 Torx 20
29 37 39162 Closing handle EF 470
7 38 19799 Screw M4 x 8 Torx 20
39 21542 Thermal cutoff clip
8
40 41436 Thermoblock complete 230V
9 40 41434 Thermoblock complete 120V
10
38 40 41435 Thermoblock complete 100V
38 41 40180 Bushing insulator electrical
39
11
42 5245 Spring washer M5
12 5 43 40190 Temperature sensor 737
13
14 28 900 6328 Strand wire white 100mm
23 900 39263 Strand wire black 100mm
15
16
27 900 39264 Thermal cutoff 167°C
15
15 900 40606 Bushing insulator electrical
14 900 39630 Strand wire yellow/green 220mm
17
26
11
13
18
15
12 15 19 14 20 21 2 40 22 2 21 23 24 41 42 43 25

Service Manual EF 470 / EF 471 33 Version 1.1 en

Spare Parts

Spare parts EF 471 Pos. EFR nr. Component

1 39167 Upper chassis EF 471
3 3 2 1 36 37 36 2 24863 Safety screw 3,0 x 12 KST/PT
3 40687 Coffee outlet & front ring EF 471 (package)
5 39379 Side panel EF 471 silver
5 39157 Side panel EF 471 coral red
23
5 42613 Side panel EF 471 green
35 6 39171 Capsule container EF 471
5 23 7 39151 Drip grid EF 471
34 8 40480 Drip tray EF 471 printed : "Nespresso"
8 40481 Drip tray EF 471 printed : "Magimix"
8 40482 Drip tray EF 471 printed : "Koenig"
8 40483 Drip tray EF 471 printed : "DeLonghi"
33
9 39197 Hose water tank / pump
44
6
10 40691 Water tank connector assembled
15
32 11 39195 Pump attachment
7 12 39196 Pump fixation
14
31 13 37384 Clip D=5mm
8 30 14 5470 Clip to tube 770
29 15 24374 O-ring 3,4 x 1,9 silicon
9 16 37454 Angle connection for hoses
10
38 17 41029 Pump 230V
38
39 17 42530 Pump 120V
11 17 41030 Pump 100V
12 18 39199 Hose pump / thermoblock
5
13 28 19 1565 O-ring 5,28 x 1,78 EPDM
14
23
15 20 36613 Angle connection for pump
27
16 21 13299 Elastic stop
15
15 22 39165 Lower chassis EF 471
14
17
26
23 16052 Screw 3,0 x 12 Torx 10
11
13 24 1053 Strain relief screwed
18
15 25 39369 Power cord Cebec 1,3m
12
15 19 14 20 21 40 2 22 2 21 23 24 41 42 43 25 25 39266 Power cord SEV 1,3m
25 40535 Power cord Israel 1,3m

Service Manual EF 470 / EF 471 34 Version 1.1 en

Spare Parts

Spare parts EF 471 (continued) Pos. EFR nr. Component

25 39368 Power cord GB 1,3m
3 3 2 1 36 37 36 25 42135 Power cord UL 1,3m
25 39271 Power cord Japan 1,3m
26 38412 Angle connection for hoses
27 39188 Electronic base
23
28 40688 Electronic set 230V
35
28 40689 Electronic set 120V
5 23 28 40690 Electronic set 100V
34
29 39154 "Coffee" button EF 471
30 39155 "ON-OFF" button EF 471
31 26392 Silicon hose
33 32 39198 Hose thermoblock / CBU
44 33 39143 Water tank EF 471
6 15 34 40685 Compact brewing unit (CBU)
32
35 39169 Cover EF 471
7
14 36 39256 Screw M4 x 25 Torx 20
31
37 39163 Closing handle EF 471
8 30
38 19799 Screw M4 x 8 Torx 20
29
39 21542 Thermal cutoff clip
9
10 40 41436 Thermoblock complete 230V
38
38 40 41434 Thermoblock complete 120V
39
11 40 41435 Thermoblock complete 100V
12
5 41 40180 Bushing insulator electrical
13 28 42 5245 Spring washer M5
14
15
23 43 40190 Temperature sensor 737
27
16 44 18904 Screw 3,0 x 16 Torx 10
15
15 900 6328 Strand wire white 100mm
14
17
26 900 39263 Strand wire black 100mm
11
13 900 39264 Thermal cutoff 167°C
18
15 900 40606 Bushing insulator electrical
12
15 19 14 20 21 40 2 22 2 21 23 24 41 42 43 25 900 39630 Strand wire yellow/green 220mm

Service Manual EF 470 / EF 471 35 Version 1.1 en

Notes

Service Manual EF 470 / EF 471 36 Version 1.1 en