ARRETT HACK

hologruhs |John'.'hcldon
1/c
HANDPLANE
|ccl
|!111 !T
Photographs by John S. Sheldon
r n
.....-...
J1unton

I
)||:n||ess|s
1999 by The Taunton Press, Inc.
All rights reserved.
Printed in the United States of America
10 9 8 7 6 5 4 3 2 1
The Handplane Book was originally published in hardcover
1997 by The Taunton Press, Inc.
The Taunton Press, Inc., 63 South Main Street, PO Box 5506,
Newtown, CT 06470-5506
e-mail: [email protected]
Distributed by Publishers Group West.
Library of Congress Cataloging-in-Publication Data
Hack, Garrett.
The hand plane book / Garrett Hack.
p. cm.
"A Fine woodworking book" -Tp. verso.
Includes bibliographical references and index.
ISBN 1-56158-155-0 hardcover
ISBN 1-56158-317-0 softcover
1. Planes (Hand tools).
T186.H33 1997
684'.082 -dc21
About Your Safet
2. Woodwork. I. Title.
97-7943
CIP
Working wood is inherently dangerous. Using hand or power tools improperly or
ignoring standard safety practices can lead to permanent injury or even death.
Don't try to perform operations you learn about here (or elsewhere) unless you're
certain they are safe for you. If something about an operation doesn't feel right,
don't do it. Look for another way. We want you to enjoy the craft, so please keep
safety foremost in your mind whenever you're in the shop.
To Helen and Vinny who saw the possibilities,
Ned who encouraged me, and
Hope who has kept me tuned and planing true
ACKNOWLEDGMENTS
No one can hope to bring together a book
like this without help. Vry few of us will
ever own all of the planes discussed within
these pages; the range and numbers of
diferent ones are simply too vast. Some are
so scarce and expensive that they are
beyond the means of most of us. Luckily,
there's no shortage of people who love and
collect planes willing to share them. I'm
appreciative of all those who ofered their
tools, books, and insights into the different
tpes of planes and how they're used.
Equally important were the people who gave
advice or encouragement along the way.
Helen Albert, for her insights and
encouragement from the beginning
Jonathan Binzen
M. S. Carter, a special collector of
miniature planes
Violinmaker Jonathan Cooper
Auctioneer Richard Crane, who's seen
more tools than most of us ever will
Michael Dunbar, a chairmaker
knowledgeable about all hand tools
Deborah Federhen, Curator of
Collections, Bennington Museum,
Bennington, Vermont
Jay Gaynor of the Colonial Williamsburg
Foundation, Williamsburg, Virginia, who
together with Joseph Hutchins made
planes as art
Barbara Hamblett, Polly Mitchell, and
the Shelburne Museum, Shelburne,
Vermont
Gerry and Jane Haviland, eternal springs
of encouragement
Bill Hildebrandt
Ted Ingraham, a plane maker and
savant of 18th-century woodworking
skills and tools
Tool historian and collector Paul
Kebabian
Vincent Laurence, a wonderful friend
and teacher
Leonard Lee
Tom Lie-Nielsen and the crew of
Lie-Nielsen Toolworks, Warren, Maine,
redefining how fine new planes can be
John Lively, who challenged and
encouraged my ideas
Noel Perrin, for his insights about all
things besides tools
Jack Playne
Violinmaker David Polstein
Cooper Ron Raiselis and the Strawbery
Banke Museum, Portsmouth, New
Hampshire
Mark and Jane Rees, writers and lovers of
old woodworking tools
Gordon Riesdel
Plane maker Leon Robbins
Ken Roberts
Photographer John Sheldon, for his
enthusiasm, spirit, and creativity
Richard Starr, inspiring kids to use
hand tools
Charles Stirling, of Bristol Design,
Bristol, England
Plane maker JeffWarshafsky, ever
curious about the fine points of planes
and planing
Caroline and Bill Wilkins, astute
collectors and gracious hosts
Windsor Precision Museum, Windsor,
Vermont
Dean Zoerheide, for his workingman's
appreciation of planes
And for my support at The Taunton Press:
Peter Chapman
Jim Chiavelli
Rick Peters
Joanne Renna
Carol Singer
CONTENTS
o Introduction
O N E + What Is a P
l
ane?
T WO TZ History of P
l
anes
T H R E E Zo P
l
ane Mechanics
F O U R O Tuning a P
l
ane
F I V E 1+ How to P
l
ane
S I X Z P
l
anes for Truing and Sizing Stock
S E V E N TZ P
l
anes for Joinery
E I G H T TOZ P
l
anes for Surfacing
N I N E T1 Scrapers
T E N To+ P
l
anes for Shaping
ELE V E N ZT Specia
l
ty P
l
anes
T WE LV E ZZo Contemporary P
l
ane Makers
T H I R T E E N Z+Z Buying P
l
anes
ZOo Bib
l
iography
Zb Index
INTRODUCTION
A man who wants to work must attach value t the best tools.
Handplanes have become such an
integral part of my furniture making
that I cannot imagine working without
them. This isn't to cling to some
romantic image of the past-I'm still a
practical Yankee with a shop full of
machines. The simple truth is that a
plane works better and more efficiently
than a machine in many situations.
What machine can fit a drawer as well
as a plane, one thin and thoughtful
shaving at a time?
Learning to use planes can improve
your craftsmanship. No tool matches the
clarity and polish of a surface cut with a
plane. No machine leaves a better glue
surface or cuts such a tight-fitting joint.
There are so many varieties of planes
panel raisers, molding planes, and
chamfer planes to name but a few-that
using them can't help but encourage you
to work in new ways or add interesting
details. And if that isn't enough, planes
are a lot more plea sura ble to use than
machines and will make your shop a
quieter and cleaner place to work.
Learning to tune and use planes isn't
difficult. Any woodworker has the
skills but maybe not all of the necessary
information. No planes I've ever bought
came with an owner's manual, although
it would be nice if they had. Maybe
then my first attempts wouldn't have
been so frustrating-the plane ending up
so thoroughly clogged that it did more
damage than good. Few books were
helpful; they focused more on the history
of planes than on offering practical
information for the contemporary wood
worker. So I've set out to remedy that.
I like to think of this book as a plane
owner's manual. It explains the basics
of how a plane cuts and describes how
to tune, sharpen, and adjust a plane to
work better than you ever thought
possible. Every type of plane you'll ever
likely need is discussed, along with
planing techniques for each, from
holding the plane to clamping the work
and troubleshooting problems. I've also
included the especially useful
information that ordinary manuals
never seem to discuss, such as how to
read the grain of a board and plane
figured wood, how to decide which
planes are essential for your shop, and
how to know where to look and what
to look for when buying them.
-Goethe
Specific planes and techniques are
introduced as you might use them in
building a piece of furniture. The planes
are grouped according to the work they
do: truing and preparing stock, cutting
joinery, smoothing surfaces, and cutting
moldings or other shaped decoration.
The range runs from essential bench
planes to such oddities as a spill plane,
where producing a useful shaving-not
an improved surface-is the intent.
The final chapters offer a different
perspective on planes. Here are the
plane-making techniques of a handful
of contemporary craftsmen, advice
from an auctioneer 30 years in the tool
business, and the stories of a few
incurable collectors.
Planes were once one of the most
important tools in a carpenter's chest,
making possible a whole range of
techniques difficult or impossible with
other tools. They are no less relevant
today. Use this book as a guide and no
matter what you know about planes, it
will help you gain greater confidence and
skill and experience greater pleasure
working wood.
3
WHAT I S A PLANE?
Many woodworking operations which we take for grnted would be
impossibly laborious without Planes. A worker with the right Plane for a
particular task has only to concentrate on holding it in the correct attitude
in contact with the workpiece, and he can then push away freely until the
task is completed.
-R. A. Salaman, Dictionar of Woodworking Tools, 1975
I f you'd looked inside the tool chest
of an 18th- century colonial joiner, you'd
have found chisels, gouges, a bit stock
and bits, handsaws, hammers, squares,
gimlets, a hand adz, and an assortment
of planes. Some of the tools were
imported from England, while others
were made lo cally. Planes for spe cial
tasks were bought from other joiners
who produ ced them as a sideline to their
furniture work, or from skilled
commer cial plane makers. A stout
smoothing plane, a long jointer, and
many of the molding planes the joiner
likely cut himself from yellow birch and
beech and fitted with thi ck imported
cast-steel irons. Essentially, these were
wooden tools for working the resour ces
of a land ri ch in timber, for creating the
wooden essentials for the settler, villager,
and town dweller alike-from buildings
to bridges, wagons to hay forks, barrels to
sap buckets, furniture to spoons.
Before the development of the planers
and table saws common in most shops
today, everything was made by hand.
The concept of a plane i s a si mpl e one-a chisel wedged i nto a solid
body-but the tool takes many di fferent forms. Shown here are a Norri s
panel pl ane wi th steel si des and sole and rosewood i nfi l l , used for
t rui ng edges and flatteni ng surfaces, and rare Norri s wooden mol di ng
pl anes wi th shaped sol es and si ngl e i rons.
When a colonial joiner built a case of
drawers, for example, he first marked out
all the different parts on the boards and
sawed them apart with a handsaw. The
real work began in earnest with planing
the parts to size, leveling and smoothing
ea ch surface, and working each part
down to uniform thi ckness. For t
h
is he
would have pulled from his chest a heavy
ja ck plane-a stock of beech a little over a
foot long fitted with a double plane iron
and an open, curved handle at the rear.
It was a tool little changed from that
familiar to a Roman joiner, nor much
different from one likely made of cast
iron instead of wood found in a wood
working shop today.
It is hard to imagine truing and
dimensioning the case and drawer parts
by hand without using planes. Leveling
5
An 1 8th-century
j oi ner' s tool chest
woul d have hel d an
assortment of
pl anes, i ncl udi ng
many mol di ng
pl anes, a j ack pl ane,
and a coffi n-shaped
smoother, as wel l as
chi sel s, bi t brace
and bi ts, and
measuri ng tool s.
and smoothing can be done with a hand
adz and chisels, in much the same way
that a large chisel or slick is used, but
such work requires great skill controlling
the cuts, and a lot of energy besides.
Even in skilled hands it's easy to gouge
the surface and leave the parts uneven
enough to make joining or fitting them
closely together difficult. Wedge the
same chisel iron in a block of wood at a
pitch of say 45 , and you've given the
craftsman a plane-a tool that allows him
great flexibility to control the cut while
focusing his energy on driving the tool.
The simplest of planes has a flat "sole" or
base with the cutting iron projecting
through it. By tapping on the plane body
or iron its depth can be adjusted to take
6 C H A P T E R O N E
an aggressive cut to level the surface
quickly or to take a finer cut for final
smoothing. The straight and flat sole
guides and controls the cutting of the
iron so that high spots are planed off
progressively lower until the plane takes
a continuous shaving from end to end
and creates the plane the name of the
tool suggests.
Classes of Planes
Planes can be broadly grouped according
to the work they perform: truing and
sizing stock, cutting and fitting joints,
finishing or smoothing surfaces, and
shaping. An 1 8th-century joiner had
specific planes in his tool chest for each
of these different planing tasks. Although
he did not have the variety of planes
common a century later, each of his tools
was general enough to do the work
needed; if it was not, he cut a new plane
or reshaped an old one.
The need for a greater variety of
planes evolved with the gradual
specialization and separation of the
different woodworking professions. The
joiner who completed the interior
woodworking of a building needed more
specialized planes than the carpenter
who cut the frame-molding planes for
shaping trim and crown moldings, sash
and door planes for building windows
and doors, and grooving and panel
raising planes for wainscoting. Within
each trade, planes evolved to satisfy the
particular demands of both the craft and
the craftsman. Coopers took the jack
plane and curved it into a more practical
topping plane, so it could better follow
the top of a barrel when leveling the ends
of the staves. Similarly, stairbuilders
shortened and altered molding planes to
follow the tight curves of handrails. Up
until nearly a century ago many hundred
styles and types of planes were in daily
use. Basic planes such as the jack were
used throughout the woodworking
trades. Others were so specific
coachmaking tools, for example-that
the exact function of some of them has
unfortunately been lost with the passing
of the coachmaker's craft.
BENCH PLANES FOR
TRUING AND SIZING
Of all the work that planes perform, the
most basic of truing and sizing stock falls
to a class of planes called bench planes.
As their name suggests, these planes are
used mainly at a bench for planing stock
held with clamps, dogs, or within a vise.
For an 18th-century woodworker, these
were the most important planes he
owned, used throughout the working
day from leveling and thicknessing parts
to jointing edges and initially smoothing
surfaces. Bench planes are no less useful
today, although with readily available
dimensioned lumber and woodworking
machinery common in nearly every
shop, they are used less for the rough
sizing of parts and more for final
dimensioning, jointing, and fitting.
Early bench planes, made from well
seasoned stocks of quartersawn beech,
yellow birch, or more rarely dense
tropical hardwoods, vary in length from
the 7-in.- to 9-in.-Iong smooth plane to
the 26-in. to 30-in. jointer plane.
Between them are at least two more
sizes: a 14-in. to 1 6-in. jack plane and a
trying or fore plane somewhat shorter
than the jointer. The sizes and styles vary
widely due to regional differences and
each plane maker's preferences. The
longer the plane, the truer or straighter
the surface the plane cuts; a jointer is a
better choice for truing long board edges
than the shorter jack. Bench planes have
flat soles and an iron bedded at an angle
of 45 to 50 to it, the steeper angle
being preferred for harder woods. A
handle or tote of many forms behind
the iron allows a firm hold on the tool to
deliver power to it through the cut. (For
more on the anatomy of bench planes,
see Chapter 3. )
Toward the end of the 1 9th century
wooden bench planes began to give way
to cast-iron planes patented by Leonard
Bailey and others (see the top photo on
p. 8). Making such cast-iron planes
demanded a whole new method of
manufacture and an understanding of
casting technology that once developed
.
.
M .
Sargent & CO.'s Bench Planes.
These wooden
bench planes sold
by Sargent & Co. " Ieneva n Planes.-Not "arranted.
.
600, Smooth Single Iron, 2, 2 2\ Irn $0
601, 2% " 2) "

60S, Smot 2, 2 u 2 u
609, Jnc 2, 2% " 2} "
610, Fore, 2
%,
2
X"
2% " 140
61 JOintr, u 2, 2%" 2 " ,j 24 26 Ic 50
611, " 2X, 2%" 2 " " 28 ,, 30 " 1 60
Sargent & CO.'S "U. S." Bench Planes.-walTnted.

of New Haven,
Connecti cut, are
typi cal of the various
sizes and styles
avai l abl e from
commercial pl ane
makers j ust over
1 00 years ago.
W H A T I S A P L A N E ? 7
Transi ti onal pl anes
have mostl y wooden
bodi es ( usual l y
beech) and cast-iron
parts, combi ni ng
t he smooth pl ani ng
of a wooden sole
and the adjustabi l ity
of a cast-i ron pl ane.
8 C H A P T E R O N E
The appeal of earl y cast-iron pl anes, such
as the #5 bench pl ane by Leonard Bai l ey (at
rear) and an Engl i sh smoothi ng pl ane
attri buted to Marpl es, was that they had l ong
weari ng sol es that stayed true and adj usters
that made i t easy to set the depth of the i ron.
led to the production of vast numbers
of inexpensive planes. These planes
have popular features such as an easy
mechanical adjuster for iron alignment
and depth, and flat, long-wearing soles
that are sometimes grooved or
corrugated for reduced friction. Even
though some woodworkers still prefer
the feel of a wooden plane, cast-iron
planes far outlast their wooden cousins
whose soles need periodic reflattening
due to hard use and changing seasons.
Bailey and others patented another
style of bench plane, a combination
wooden-soled and cast-iron plane meant
to satisfy craftsmen who were not so
willing to part with their all-wood
planes. These so-called "transitional"
planes (see the bottom photo at left)
combine the feel of a traditional wood
plane with the mechanical advantages of
a cast-iron plane-easy adjustment of the
cutting iron and a movable frog. It's
natural to think that wood-bottomed
planes were a stage in the evolution of
the cast-iron plane and were transitional
in this way, but they were made right
along with all-cast-iron planes for almost
75 years. Their appeal was their
availability in a wide selection of sizes for
about half the cost of an all-cast-iron
plane and their ability to hold up to
rough use. Since the plane's sole is still
wood, it is worn down by use and needs
regular reflattening. Nevertheless,
transitional planes have appealed to
many generations of craftsmen who
appreciate the subtle feel of a wood plane
for varied bench-planing work.
Among the many desi gns of pl anes for cutti ng and fi tti ng joi nts are a
Stanley #90A bul l nose rabbet pl ane (at rear), one of the rarest of
pl anes, and a Sargent #1508%" Lady bug" bul l nose fi I I i ster rabbet
pl ane with fence and depth gauge.
Combi nati on pl anes evolved from pl ow pl anes to perform a variety of
tasks, i ncl udi ng cutti ng dadoes, rabbets, grooves, and tongues. These
two early desi gns are a Stanley #46 with skewed cutters (at rear) and
a Si egl ey combi nati on pl ane.
PLANES FOR CUTTING
AND FITTING JOINERY
Once the stock is prepared, a second
group of planes is brought to the work to
cut and adjust the joinery that fits the
parts together. Except for the long bench
planes, which could be included in this
group for shooting straight edges for edge
joining, joinery planes tend to be smaller
and specialized. These planes include
rabbet, dado, and fillister planes for
cutting rabbets and wide grooves or
dadoes (see the photo above); plow and
grooving planes for cutting grooves in the
edges of boards; dovetail planes for
cutting sliding-dovetail joints; shoulder
and bullnose planes for finely adjusting
joints; and low-angle planes for trimming
miters and end grain. Combination
planes often combine the joint-cutting
functions of a number of these planes.
For work across the grain, the iron is
bedded at 20 or less, with the bevel
upwards; other joinery planes have irons
bedded at 45 (with the bevel down),
similar to bench planes, or steeper still.
Some of these planes are designed to cut
cross-grain with the help of sharpened
spurs or nickers ahead of the iron to slice
the fibers cleanly.
An 1 8th-century craftsman had to
make do with only a few of these
specialized joinery planes; he would
likely have had a few sizes of dado planes,
a fillister or large rabbet plane, and a
plow plane. With the development of
more complex planes and their expanded
industrial production by such makers as
Stanley, a craftsman could afford to buy
any number of specialized cast-iron
planes for cutting and fitting joints. It
wasn't that the new planes could cut
more complex joints, but they were
easier to use and worked more accurately
than their wooden counterparts.
As with bench planes, shapers,
routers, and similar woodworking
machines have largely replaced many of
these tools in the woodworking trades.
Sadly, too, strong traditional joints have
given way to the more quickly machine
cut biscuit or dowel joint. Stilt some of
these joinery planes are just as useful
today to fine-tune joints cut by hand or
with a machine.
PLANES
FOR SMOOTHING
Among the most useful tools in any
contemporary shop are the third class of
planes: those used for the final leveling
and smoothing of surfaces. Because they
are no different in design and are used in
a similar way at the bench, smoothing
W H A T I S A P L A N E 7 9
Engl i sh smoothi ng
pl anes ar e among
the most beauti ful
pl anes ever made,
and they work as
well as they l ook.
Shown here are an
A6 Norri s (at rear)
from the famous
company of T. Norri s
of London and a
smoot hi ng pl ane
by Spi ers of Ayr,
Scotl and, the first
commercial maker
of such pl anes.
Scrapers are versa
ti l e tools that can
smooth surfaces
that are diffi cul t to
pl ane. The si mpl est
scraper is a pi ece
of sawbl ade, but
easi er to use are
handl ed scrapers
such as the ram' s
head scraper at
rear, a spokeshave
type scraper in the
foreground, and a
smal l , speci al ly
made tool for scrap
i ng a convex profi l e.
planes are sometimes included with the
bench planes. How they do differ is in
the way they are tuned and in the degree
to which smoothing planes have evolved
on their own to suit their specific
purpose-to such beautiful tools as
1 0 C H A P T E R O N E
dovetailed steel, brass, and rosewood
Norris planes capable of smoothing the
most difficult woods (see the photo at
top). Whether of wood, metal, or some
combination, smoothing planes tend to
be small and heavy, with a tight mouth
and a finely set iron. Since they are used
for the final leveling of a surface already
worked on by other planes, their small
size is an advantage for easy maneuvering
as their weight helps them hug the
surface. A light cut, a heavy iron, and the
overall massiveness of the plane result in
chatter-free smoothing cuts and a
polished surface.
Scrapers and scraper planes, versatile
smoothing tools that complement
smoothing planes, are included in this
third class. Although they look and work
slightly differently from planes with a
chisel-like iron, they are essentially plane
tools. With a thin steel iron held at a
high angle to the surface, scrapers can
cut or scrape fine shavings from wildly
figured or difficult wood-often better
than any other tool. Shape the iron, and
scrapers can "scratch" shallow profiles
similar to a molding plane along straight
or curved edges. Substitute a toothed
iron, and this tool is useful for roughing
veneers for a good glue bond or for
aggressive leveling of very difficult woods.
Because they are so useful, scrapers are
found in many forms throughout the
woodworking trades.
PLANES FOR SHAPING
A final group of planes shape surfaces or
edges. These tools are as varied as
molding planes that cut the wood with
shaped irons and corresponding shaped
soles (see the top photo on the facing
page), panel-raising and chamfering
planes with straight irons held at an
angle to the work with the aid of a
shaped sole, and compass planes with
curved soles and straight or curved irons.
Shaping planes could be further divided
into those that shape decoration
(molding planes) and those that work
curved surfaces (compass planes).
Categorizing some of these planes is
hard because nearly all of them do more
than just cut shapes. For example, a
compass plane shapes the surface and
can also leave it as smooth as if finished
with a smoothing plane. This points out
the basic difficulty of trying to put
planes neatly into grou ps; many will do
varied work depending upon how they
are tuned and in whose hands they are
used. Some just don't fit neatly into any
group. Where would Stanley's Universal
Plane #55 fit in these categories, "a
planing mill within itself" capable of
cutting joints, moldings, truing and
shaping edges, plowing grooves, and
more besides? Or how about an ice plane
(see the bottom photo at right)?
Of the many types of planes in
production and in use up until the
middle of this century, very few are still
being made today. Even the best
woodworking catalogs list at most a
couple of dozen planes, compared to the
many hundreds in all sizes and types that
Stanley Tools and others once offered.
With few new, quality planes available,
one might well believe that planes are
steadily and slowly passing from the
woodworking trades. To an extent this
is true. With the simultaneous
development and marketing of routers,
shapers, jointers, and every imaginable
woodworking machine, planes are used
less often for the tedious and strenuous
tasks many were designed for.
Yes, gone are the days when each
craftsman made many of his own
wooden planes and a fancy inlaid tool
chest to store them in as a rite of passage
and learning the joinery trade. As
artifacts of our culture, some of these
handmade tools-beautifully made
boxwood and brass plows, fillisters, and
complex molding planes-are better left
to be admired and studied by collectors
and historians. That still leaves a wealth
of usable planes of every description.
To find out the real story about the
vitality of these tools today, go to any tool
auction and you'll be amazed at how
eagerly sought out are planes once
common 50 or more years ago. Planes
that once sold for a few dollars can now
bring a hundred times as much. Or use
one of Lie-Nielsen's new planes, recast
and better engineered versions of earlier
One mi ght have
found a stack of
mol di ng pl anes wi th
matched pai rs of
hol lows and rounds
l i ke thi s for sal e at
a tool deal er a
century or more
ago. The sal es on
the outsi de were
vi si bl e, and as l ong
as the stack was
even, chances were
good that each ti er
was a matched pai r.
Thi s odd tool l ooks
and works l i ke a
pl ane, except that it
shaves ice rather
than wood ( maybe
for the first sl ush
dr i nks?). The i ron
is sharpl y toothed
l i ke a saw, and the
body i s made of
al umi num to
prevent rusti ng.
Stanley planes, and try to resist its
beauty and smooth cutting. Better yet,
talk with any good craftsman and
chances are he has a toolbox full of
favorite planes that he can't imagine
working without.
W H A T I S A P L A N E) 1 1
HISTORY OF PLANES
The invention of the Plane was the most important advance in the histor
of woodworking tools in the last two thousand years.
-R. A. Salaman, Dictionary of Woodworking Tools, 1975
Early in my adventure with planes it
was easy to appreciate the wide range of
work that planes could do, but they were
still just some of the many tools I used
during the course of a day. It wasn't until
I started using a noble old Scottish
smoothing plane, a heavy and beautiful
Spiers of steel, rosewood, and bronze,
that I became really curious about the
history of these tools and planes in
general. Here was a plane so different
from my Bailey smoothing planes that
clearly embodied the exceptional skill of
its maker of over a century ago. Into the
worn and polished wood was stamped
the maker's name along with the name
of the craftsman who had owned and
used this plane. Why did this tool work
so well, and where did the design come
from? What was the inspiration of the
plane maker that combined his skills,
knowledge, and artistry in this plane?
Who were the craftsmen who used such
tools when other furniture makers chose
cast-iron "Bailey-pattern" planes?
This earl y-1 5th-cent ury i l l umi nati on from the Bedford Book of Hours,
enti tl ed "Bui l di ng t he Ark, " shows medieval tool s, i ncl udi ng pl anes, at
work. ( Photo used by permi ssi on of The Bri ti sh Li brary, London )
Understanding how planes have
evolved will deepen your appreciation
of these tools and offer much insight
into the creativity of the toolmakers
who made them, the craftsmen who
used them, and the society that shaped
them both.
Early Toolmaking
Man the toolmaker has always been
trying to improve his tools. Ever since
prehistoric man chipped a crude cutting
edge from a hunk of flint, he had a tool
to scrape wood or work other materials.
The next logical step was to shape a
handle and lash it to the sharpened
flint with strips of animal hide and he
had an ax. Every advance created better
tools that extended the natural motion
of his anns, hands, or body. However
1 3
sophisticated the hand tools of later
ages, they don't deviate from this very
simple purpose.
The further development of tools was
limited only by the materials they were
made of-how difficult the material was
to work and how durable the finished
tool. A handled stone hammer was a big
improvement over a stone held in the
hand, but it wasn't until man learned
how to smelt copper, and later bronze
from copper and tin ore, that toolmaking
could make the next leap forward.
Copper was easily freed from the ore and
could be worked into useful cutting
tools, but bronze was more useful still.
Bronze is a hard metal that melts easily,
can be cast in many forms, and can be
sharpened to hold a better edge than
any copper tool. It was during the
Bronze Age that some of the basic
carpenter's tools evolved: the ax, chisel,
adz, and saw.
Most of the tools familiar to us today
did not develop until the discovery of
ways to smelt iron from hematite ore
ushered in the Iron Age some 3, 000
years ago. Here was a material far more
available than bronze, a material that
could be hammered and shaped, that
held a good edge, and that could be easily
resharpened. But iron is a complex metal
that doesn't yield its secrets easily.
Smelting the ore results in a weak iron
full of impurities. Only by repeatedly
heating and hammering the metal can
these impurities be worked out and
"wrought" (meaning worked) iron be
made. Each time wrought iron is heated
in a charcoal fire and hammered, it
absorbs some carbon and gradually
becomes steel, which is much better for
toolmaking. Steel in this form is tough
but unfortunately too brittle. It wasn't
until sometime during the Roman era
that two processes were discovered that
allowed the forging of truly useful tool
steel: quenching and tempering.
1 4 C H A P T E R T W O
Possible Evolution of the Plane
EGYPTIAN ADZ
WEDGED ADZ
ROMAN PLANE
One theory (proposed by historian J. M. Greber)
is that the plane evolved from the adz-from a
tool pulled to one pushed. The key to the
change was wedging the iron securely in a
stock that controlled the cutting action and
angling the beveled iron away from the
direction of the stroke.
Quenching, rapidly cooling the red hot
metal in water or oil, hardens the steel.
Tempering, reheating the steel to a low
temperature, softens this hardness
enough to create tough cutting edges
that are not too brittle and likely to crack
or chip in use.
The known origins of the plane follow
this understanding of turning iron into
tool steel. The earliest discovered planes
are Roman, but it is possible that the
plane was a tool known to earlier
cultures (see the drawing on the facing
page). What is strange is how fully
formed the plane is when it appears,
without any clear antecedent. Yet well
over 1, 000 years before, Egyptians were
building furniture as sophisticated as
that of any age since, with dovetails,
mortise-and-tenon joints, inlays of ivory
and gold, veneers, frames and inset
panels, and decorative moldings. Was all
of this fitting and smoothing done
entirely with saws, chisels, adzes, rasps,
and sanding stones? We know that the
Egyptians had bronze chisels with
hammer-hardened cutting edges, which
could have been held in some sort of
wood body and used like a plane, but to
date no such tools or pictures of them
have been found to establish that
Egyptians might have invented the plane.
The First Planes
The earliest known planes, dating from
AD. 79, were found preserved in the ash
at Pompeii. Enough similar Roman
planes and plane irons have been
unearthed elsewhere to give us a good
idea of how these tools looked and
worked. The simplest of these tools are
made entirely of wood with an iron
cutter wedged against a cross-bar-very
much like any basic wooden plane made
even today. Some surviving Roman
planes have bodies made of wood
partially covered over with iron and
riveted together, forming the sole and
the sides of the body (see the photo
above). A simple handhold is cut into the
wood at the rear. The Roman plane
maker was probably well aware of the
long-wearing sole and overall durability
of an iron-clad plane that more than
Earl y pl anes, such
as thi s Roman
carpenter' s pl ane
dati ng from the late
4th century, united
a steel sole (and
often si des) with a
wooden body (whi ch
has not survived on
thi s pl ane). ( Photo
copyri ght Readi ng
Museum, Readi ng,
Engl and. Al l ri ghts
reserved. )
justified the added trouble to make it.
Another form of Roman plane is all
wood except for iron plates reinforcing
the sides of the plane at the throat.
It's amazing how little these early
planes have changed from the tools used
by a carpenter today. A modern plane is
more likely to be made of cast iron, the
steel in the iron is tougher and holds an
edge better, and the iron can be adjusted
more easily than in the earlier tools, but
the basic concept has not changed. The
concept is a simple one-a tool with a
cutting iron wedged in a plane body that
allows good control of the cutting action.
Little is known about how planes
were used or what they looked like from
Roman times through the Middle Ages
and into the early Renaissance. Since
hardly any planes have survived, what we
do know comes from secondary sources
such as carvings, stained-glass windows,
and illuminated manuscripts. In one
such illumination, Building the Ark (see
the photo on p. 1 2), we see that planes
are in common use and little changed
from Roman prototypes. From other
H I S T O R Y O F P L A N E S 1 5
'Iy
;0 ..

! bl'- . .
c
"

'
J., 10"

Jb,'I'
Engravi ngs from works such as Deni s Di derot's Encyclopedie give an i dea of the types of pl anes in use
i n the 1 8th century.
sources we know that planes had evolved
in a range of sizes, and specialty planes
such as molding and rabbet planes had
begun to appear. Wood was used to build
nearly everything from ships to military
machinery, and planes must have been
important tools throughout this period.
One of the greatest impediments to
change in tool design and methods of
working was the power of the guilds,
which began to form among artisans and
merchants during the Middle Ages.
Guilds grew out of the gradual division
and specialization within the wood
working trades, into such groups as
1 6 C H A P T E R T WO
carpenters, furniture makers, ship
wrights, and wagonmakers. Guilds
regulated every aspect of each craft, from
the training of apprentices to establishing
wages and prices for finished goods, and
they guarded trade secrets and working
methods as well. Apprentices copied
masters in what became an inflexible
system, discouraging innovation and
stifling the evolution of new tools and
ideas. It's no wonder, then, that the basic
tools and ways of working wood
remained essentially unchanged until
the strength of the guilds waned in the
early 1 8th century.
We do have a glimpse into guilds, the
woodworking trades, and the range of
planes in use at the time through Joseph
Moxon's Mechanick Exercises, or The
Doctrine of Handy-Works, published in
London in 1678. It is the original "how
to" book, but written more for the
curious gentleman than for the workman
trying to learn the trade of house
carpenter, joiner, or turner. Nevertheless,
it is one of the first books to illustrate the
tools in use for these trades and to
explain how to set up and use bench,
rabbet, plow, and molding planes. We
can learn even more from two books
published about a century later: Denis
Diderot's Encclopedie and Andre-Jacob
Roubo's L'rt du Menuisier (The Skill of
the Cabinetmaker) Diderot describes
nearly every trade, and includes
extensive engravings of their shops, tools,
and methods. All three books give clear
insight into woodworking tools and
methods before great changes took place
in the 19th century.
Through these books and other
sources, we know of at least two subtle
changes in plane design that had
occurred: The iron was wedged into
place in tapered grooves (or abutments)
cut into the sides of the body rather than
against a cross-bar, and handles were
evolving to designs common today.
Wedging the iron in tapered grooves
with a more thinly shaped wedge-a
method still used for most wooden
planes-reduced the plane's tendency to
clog. Subtle changes in the throat shape
helped the plane work better, too.
Whereas Roman planes had a handle
formed in the plane body and later
ones had a simple rear handle, handles
were gradually evolving to the more
upright open or closed tote we know
today. For a more positive and comfort
able grip, Continental craftsmen added
an upright handle in the shape of a horn
to the toe of the plane. Over time this
became the sculpted, rounded cow's
horn still common on German and
Austrian planes (see the photo below)
Continental craftsman were also apt to
decorate their tools with personal
touches-carved or stamped initials and
dates, punched or chip-carved designs,
and gracefully carved throats. Meanwhile
English planes, which would later
influence American tools, maintained
simple, restrained lines.
These two horn
planes show the
upri ght handl e and
decorative detai l i ng
characteristic of
European pl anes.
HIS T O R Y O F P L A N E S 1 7
The Development
of Modern Planes
Many changes occurred within the
woodworking trades and society in both
England and America during the last
half of the 17th century into the
18th century, and with these changes
began the evolution of modern wood
working tools.
One of the most far-reaching changes
was the gradual specialization and
sophistication of the woodworking
trades. This happened first in England
and later in the Colonies due to a
growing population, changing tastes,
increased wealth, and demand for all
types of goods. The changes in building
tastes illustrate this quite clearly. As
houses in America followed the
sophisticated English Georgian style, the
hewn house frame was covered with
paneling and trim. No longer were just
the skills of a carpenter required, whose
work was now confined to erecting the
frame and the sheathing, but also the
talents of a joiner completing the
interior. Besides the basic tools of the
carpenter, the interior finish required
planes to cut fielded panels, to plow
grooves for these panels, to cut crown
and other moldings of all sizes, and to
build window sash and doors. The
cabinetmaker who built the furnishings
needed special planes, too, as tastes
changed from heavy, simple solid-wood
furniture to sophisticated inlaid and
veneered furniture of exotic or wildly
figured woods.
It is possible that one early
specialization within the woodworking
trades was plane making, although there
is no evidence of this until about 1700.
Thomas Granford of London was the
first plane maker known to "sign" his
work. This was a profound change that
has had an effect right up until the
1 8 C H A P T E R T WO
Stampi ng pl ane i rons with the maker's mark was an early form of
adverti si ng. "Warranted Cast Steel , " stamped on these two i rons,
was known for its superi or qual i ty and i ts abi l i ty to hol d a keen edge.
present, that of separation between the
plane maker and the plane user. Before
this time, individual craftsmen made
their own planes as the need arose, with
the irons coming from a local blacksmith
or from small specialized manufacturers.
It was fairly simple work for a craftsman
to fashion a new bench plane as the work
demanded. As it was, wooden planes
needed to be regularly replaced, because
they lasted only so long under hard use.
Whether due to normal wear or regular
reflattening of the sole, the mouth of the
plane eventually grew too wide and the
plane worked poorly.
Another change hastened the shift
from each craftsman making his own
planes to specialized makers: the need
for more complex tools and more tools
in general. As the work of a joiner
demanded planes to cut moldings, raise
panels, and the like, he increasingly
turned to individual plane makers with
the tools and ability to make them.
Whereas a jack plane was easily made,
complex molding planes and plow planes
took skills and tools not easily acquired.
As the population grew and with it the
demand for more goods of greater
variety, more craftsmen were needed for
the work. Since this was well before
industrialization, this meant a growing
need for planes and woodworking tools.
Specialized plane makers moved to fill
this market, eventually leading to the
gradual conformity of sizes and shapes
of planes.
Paralleling the trade of specialized
plane maker was the ironworker who
made plane irons, files, and other edge
tools. Since the late Middle Ages,
Sheffield, England, had become an
important center in the steel-making
trade, due in large part to its experienced
smiths and plentiful river power to
turn water wheels and grindstones.
Importing Swedish iron because of its
purity, small manufacturers forged an
array of superior-quality plane irons and
edge tools in many shapes and sizes.
Benjamin Huntsman's process of making
crucible cast steel further improved the
quality of edge tools from 1742 onward,
to the end that Sheffield irons were
regularly exported throughout the world
(see the sidebar on p. 45) . Throughout
the 1 9th century many types of
Sheffield-made plane irons and steel
plane parts made to the highest standards
were offered for sale through the catalogs
of American plane makers. Even as late
as 1939, Stanley proudly states in its
catalog of that year that its irons are
stamped from the "best English steel."
The i ntroducti on
of the doubl e i ron,
as on thi s unusual
mol di ng pl ane for
heavy work, was a
major devel opment
i n the history of
pl ane desi gn.
Blacksmithing skills and an
understanding of iron arrived in the
Colonies with English immigrants, but
it was a long time before domestically
forged irons could equal those of
Sheffield. Wrought iron was made from
naturally occurring bog iron as early as
17 19, but it was unsuitable for cutting
edges. To make a good plane iron, a steel
edge, most likely imported from
Sheffield, was forge-welded to the
wrought-iron blank. Early plane irons
show this distinct weld line between the
different materials. When the cutting
edge was worn down by use and
sharpening, a blacksmith would "steal"
it, or weld on a new one.
H I S T O R Y O F P L A N E S 1 9
Through all of this time, each trade
used a greater variety of planes, but the
basic physics of the tools was essentially
unchanged from centuries earlier.
Sometime late in the 1 8th century came
a major improvement that did change
plane design-the introduction of the
double iron (see the photo on p. 19).
A slightly curved cap iron screwed to the
cutting iron greatly improves the plane's
ability to cut difficult wood. Not only
is the double iron heavier, more rigid,
and more stable, but the cap iron also
supports the cutting edge and helps curl
the shavings and breaks them as they
are planed. This simple mechanical
advantage reduces tea rout and leaves a
smoother surfaces. Many specialized
planes had a single iron, but most of the
hardest working bench planes were
fitted with double irons, costing roughly
twice that of a single iron.
EARLY PLANE MAKING
IN AMERICA
Before plane making became a
specialized trade in America early in
the 1 8th century, most tools were
imported from England or arrived with
immigrants. What tools the colonial
craftsman didn't buy from England he
made himself and most likely fitted
Early wooden-plane makers bol dl y stamped thei r names and towns
into the toe of thei r planes. Shown here (from left) are a Ni chol son
pl ow pl ane with a fence riveted to the arms, a Chel or panel rai ser, a
Ni chol son crown mol der, and ( i n the foreground) a si mpl e round.
20 C H A P T E R T WO
with imported irons. England offered
a greater variety of tools, and as some
craftsmen felt, superior quality, too.
Planes of all sizes and shapes were
imported, along with plane irons and
plane parts: fillister and plow plane
depth stops, iron soles for smoothing
planes, and plow skates. With close
trading ties and a shared history,
English tools set the pattern for and
influenced American tools well into the
19th century. It wasn't until the Civil
War that this changed significantly,
although even today English tools still
have a special appeal.
The earliest plane makers in America
worked either in or close to coastal towns
important as trading or population
centers. The Colonies lagged behind
England in the specialization of the
plane maker for a number of reasons.
There was less demand for the tools from
a smaller population, good tools could
be easily imported, and craftsmen were
initially concerned more with creating
the necessities of life rather than
decorative furniture or fancy buildings,
which required specialized tools.
Deacon Francis Nicholson, working in
Wrentham, Massachusetts, from about
1 728 to1 753, is the first documented
colonial plane maker. Many Nicholson
planes, along with those of his son
John, his black slave Cesar Chelor, and
a handful of others, have survived.
Except for slight differences in length
and wedge finials, and the use of yellow
birch instead of the more usual beech,
they could easily be confused with
contemporary English planes.
One of the few ways we can follow the
development of the plane-making trade
in America is through the name that
each maker stamped into the toe of his
planes (see the photo at left). Some
makers included their town in a form of
early advertising. By studying census

records, probates, indenture agreements,
and the like, we can date individual
makers. Some makers immigrated from
Europe and continued working, giving
us insight into differences between the
plane-making trade here and in England.
The irony of studying any planes is that
the ones that have survived are the ones
that were less used for some reason;
planes well used wore out and usually
did not survive.
As the population grew and colonial
society matured, changing tastes once
again give us insight into the demand for
specific planes and their gradual
evolution. One way that changing tastes
were popularized was through
architecture books, both those for the
craftsman and those for wealthy
gentlemen builders. Two of the most
important were Batty Langley's The City
and Country Builder's and Workman's
Treasury of Designs, initially published in
`
1740, and Thomas Chippendale's The
Gentleman and Cabinet-Maker's Director
of 1 754. With such books, carpenters
and joiners could learn rules for
proportion and common classical
moldings. As references, they guided the
craftsman in selecting or making
appropriate molding planes in accord
with prevailing international tastes. Such
books also served the needs of molding
plane makers, allowing them to keep
abreast of changing architectural styles
and produce planes that cut moldings in
the latest fashion.
The Federal style was the first wholly
American style. With advances in
movable-type printing presses and the
plummeting price for paper, information
about the new style was easily dispersed
through design books and penny
magazines. In 1806, Asher Benjamin
published the first original American
Thi s page from an earl y bui l der' s manual
shows layout l i nes for Greci an mol di ng
profiles that were to become the basi c
mol di ng forms.
work on architecture, his American
Builder 's Companion. The changes in
molding styles he proposed were as
different as the new Federal style.
Typical molding profiles before
then were based on Roman prototypes
and arcs of circles. Benjamin's moldings
were based on quite different Grecian
models-the soft and subtle curves of
parabolas, ellipses, and hyperbolas (see
the illustration at left). His book explains
simple mechanical methods for laying
out the new ovolos, astragals, and ogees
that were to become the basic molding
forms right into the 20th century.
Now carpenters and furniture makers
needed a whole new set of molding
planes in the latest style, which a
growing number of plane makers readily
supplied. While these were sweeping
changes, it was nothing like what would
occur with industrialization and the
development of the cast-iron plane later
in the century.
The Golden Age
of Planes
By the end of the 18th century the
I ndustrial Revolution was well under way
in England. Even so, with a surplus of
labor and lingering effects of the strong
guilds, hand methods of work persisted.
English sawyers effectively resisted
powered sawmills long after they were a
common sight in America, turning out
millions of board feet of lumber,
shingles, and clapboards from its vast
forests. Industrialization was quickly
H [ S T O R Y 0 F P L A N E S 21
The Woods pl ani ng
machi ne ( c. 1 830)
was one of the earl i
est water-powered
machi nes used to
pl ane stock flat. The
heavy wood frame
supports a ci rcul ar
cutterhead wi th two
gouge-l i ke steel
cutters set into the
outer ri m. (The
machi ne shown here
i s housed i n the
Wi ndsor Preci si on
Museum, Wi ndsor,
Vermont . )
22 C H A P T E R T WO
embraced here by a society independent
of guilds, with a strong entrepreneurial
spirit and a shortage oflabor. Imagina
tions were captured by the possibilities
of machines. It was just a matter of time
before turbines (and sound hydraulic
principles) would be applied to textile
manufacturing and eventually to
woodworking machines of all types.
The development of machines
brought far-reaching changes to the
woodworking trades in village and city
alike. With a growing population and
demand for all types of wooden goods
came the incentive to develop machines
to speed production and take over
some of the laborious tasks. Work once
done entirely by hand was now done
by machine. It wasn't long before
whole shops were mechanized, planing
wood, cutting moldings, or building
sashes, doors, and blinds. Along with
industrialization came a better
transportation network and the end of
the largely self-sufficient community.
Rather than heralding the end of
hand tools, initially mechanization only
increased the demand. Hand tools were
needed to build machines made largely
of wood, and they still had a flexibility
that machines lacked. Ironically, plane
makers were among the first to see the
possibilities of the machine, as a way to
increase their production and create
new and varied tools. Planers sped up
the milling of wooden plane stocks
that could then be further worked
upon with circular saws and mortisers.
Once industrialization was under way,
fascination with the machine and
machine processes drove tool design
forward. As the century progressed,
toolmakers turned their attention to
new materials and to creating the
new tools needed by craftsmen relying
on machines.
CAST- IRON PLANES
Cast iron was one of the new materials
toolmakers turned their attention to.
While not exactly new-the Greeks and
people of India had used cast iron-it
wasn't until the mid-19th century that it
was used for planes and other tools. Cast
iron is simply molten iron with some
impurities and a carbon content between
2% and 5% that is poured into a mold to
cool. Its advantages for making planes are
obvious: The plane body is stable, the
sole is long-wearing, the throat stays
consistent, and each plane is identical
and inexpensive.
Hazard Knowles was the first to try
casting planes. Interestingly, his 1 827
patent was the first significant plane
patent in America, and it was for a cast
iron plane that wouldn't be popularly
accepted for another 50 years. Many
other makers experimented with casting
planes, either as complete planes or in
combination with wood as in later
transitional types; initially, none could
make planes in sufficient quantities or
economically enough to compete with
wooden planes. It wasn't until past mid
century that the man we associate most
with cast-iron planes, Leonard Bailey,
got started. It took the huge advances in
production technology spurred by the
Civil War to finally establish cast-iron
planes as a superior alternative to wood.
The necessity of making armaments
during the Civil War accelerated the
development of machines, machine
processes, and the technology associated
with interchangeable parts. These
developments required factories. Making
cast-iron planes required the same
organized production system to turn
out large numbers of identical parts.
Leonard Bailey started making cast-iron
planes with Stanley in 1869. In the 1 870
catalog Stanley offered an impressive line
of 28 different sizes and types, both cast
iron and wood-bottomed. Even though
Pocket catal ogs were one of Stanl ey' s many ways of adverti si ng i ts tools. Made for
carpenters and woodworkers to carry in thei r tool boxes, catalogs were for handy reference
or to t humb through duri ng breaks when dreami ng about future purchases.
such planes were unknown to most
craftsmen and the wooden-plane business
was firmly established, by the end of the
century Stanley was selling millions.
Leonard Bailey was one of the
brilliant inventive minds behind the
success of cast-iron planes. It was from
firsthand experience as a cabinetmaker
that he was interested in improving his
tools. From his first patent in 1 855 to
1869 when Bailey, Chaney and Company
was bought by Stanley Rule and Level,
Bailey experimented with and improved
many designs for bench planes and
scrapers. He invented such things as the
depth adjuster and the lever cap still
common on planes today. In fact, the
design of the "Bailey-pattern" bench
plane has remained essentially
unchanged for well over a century.
The agreement between Stanley and
Bailey didn't last. In 1875 Bailey broke
away and started making a line of planes
under the trade name "Victor." What
followed was years of disagreement
between them, as Stanley continued to
get larger (typically by buying up
competitors such as Victor) and Bailey
finally gave up making planes.
What did last was Bailey's
contribution to cast-iron planes and
Stanley's incredible success with them.
Success was not immediate though. For
one thing, the planes were expensive
H I S T O R Y 0 F P L A N E S 23
compared with wooden ones. In 1 870,
the first year they were offered, # 5 bench
planes sold for $7. 50 each; a premium
wooden jack was closer to $ 1 . 50. As
production increased, the next year the
price dropped to $6.00, and by 1 892
the same plane was $ 3. 75. Stanley
aggressively marketed its planes through
pocket catalogs, trade magazines, store
displays, and exhibitions. The advantages
of the planes were so compelling that
sales gradually rose. In the words of a
contemporary catalog, "Increased sales
meant increased production, increased
production meant better facilities, better
facilities meant better goods and lower
prices . . . " and the promise of factory
production of cast-iron planes was
fulfilled. The demise of the wooden
plane was just a matter of time.
THE DEMISE
OF WOODEN PLANES
Wooden planes were in peak production
when Stanley first started producing
cast-iron planes. But during the last
quarter of the 1 9th century three
influences drastically cut the demand for
wooden planes: the success of cast-iron
planes, a gradual decrease in the need for
handwork with the increasing availability
and variety of woodworking machines,
and the consolidation of the wooden
plane industry into a few large makers.
Once they became readily available
and inexpensive enough to compete with
wooden planes, cast-iron planes soon
won out. They were simply easier to use
and adjust; they stayed true and needed
little sole maintenance. Wooden planes
couldn't compete with the incredible
variety of cast-iron planes that Stanley
and others introduced year after year.
Why carry a toolbox full of wooden
molding planes when a Stanley #55
combination plane could do it all and
24 C H A P T E R T WO
then some? Meanwhile, molding and
milling machines reduced the demand
for the work wooden planes usually did.
The final blow to wooden planes was
the demise of the small maker who
could no longer compete against a few
large manufacturers. Only major
toolmakers such as Ohio Tool, Auburn
Tool, and Chapin-Stevens could afford
the factories and large-scale production
necessary to make wooden planes
economically. Auburn even competed by
using prison labor1 By World War I there
were few buyers left for wooden planes.
The bright side is that wooden planes
never disappeared entirely. They persisted
longer in England, again because of the
conservatism of the trades and a
surplus of labor. That is why English
molding planes can be found that cut
Victorian moldings, whereas in this
country such moldings were typically
machine made. European makers such
as Primus and E. C. E. never stopped
making wooden planes either, although
there seem to be fewer and fewer
available in woodworking catalogs these
days. Old wooden planes can still be
found at any flea market or auction or
from tool dealers. So many were made
that there is likely to be a good supply
for a long time to come.
Whereas few wooden pl anes are sti l l made in Ameri ca, Conti nental European plane makers
cont i nue to produce them, such as thi s Pri mus pl ane made of pear wi th a l i gnum-vitae sol e and
uni que adjusters.
In the i mmediate post-World War II peri od, economi cs drove the
market to low-cost and l ow-qual i ty tool s. Shown here (from rear) are
a cast-al umi num Sargent #600 with "4-Edge Bl ade"; a Stanley " Handy
man" in the famous two-tone colors, also with a repl aceabl e " Ready
Edge Bl ade"; and a Mi l lers Fal l s #8900 of tradi ti onal desi gn with dark
pai nted knobs and tote to resembl e the rosewood once common.
Two uni que 20th-century pl anes are a Surform (c. 1 956), thought by
some to be the onl y modern advance i n pl ane technol ogy, and, i n the
foreground, a razor pl ane that uses a di sposabl e razor bl ade as a
cutter, el i mi nati ng the need for sharpeni ng.
From the Golden
Age of Planes
to the Present
Stanley dominated the market in the
Golden Age of planes, from 1 870 up to
World War II. It's hard to convey the
incredible range of planes Stanley made,
literally hundreds, and many that no one
else did, such as curved rabbet planes,
dovetail planes, and beltmaker's planes.
Stanley's Bed Rock line of bench planes
was the best on the market. Other
manufacturers such as Sargent, Union
Tool, and Millers Falls competed with
their own lines of cast-iron planes, either
of their own innovation or patterned
after expired Stanley patents. Only
Sargent came close to Stanley in the
variety of planes it offered, and they
were every bit as well made, too. But it
was inevitable that the demand for
planes would diminish. Other than in
a few specialized trades, a craftsman
using hand tools just couldn't compete
economically with machine-produced
products.
Stanley continued to offer many of
its planes right up until World War II,
even though by then the market was
much smaller. It hung on because it still
aggressively marketed its tools, not only
in America but now throughout the
world. In England, Stanley competed
with Edward Preston, a maker of fine
quality cast-iron tools, and later Record.
In the United States, demand had
persisted beyond the turn of the century
because the population was still growing
and moving westward. Carpenters
building the housing still needed a few
basic planes. Only a few specialized
trades-furniture makers, stairbuilders,
and others-used any more than these.
Building had become a process of
assembling component parts
dimensioned lumber of all sorts and
sizes, machine-made moldings, doors,
and windows. Stationary powered shop
tools were readily available, and by
World War II, portable electric wood
working machines, too. By mid-century
only a few of the basic bench planes were
in demand and thus economically viable
to keep producing. Our long history of
working with hand tools, while not
entirely over, was vastly different from
even a few generations before.
H I S T O R Y 0 F P L A N E S 25
Mi l l ers Falls smooth
ing pl anes i ncl ude
(at rear) a del uxe
#209 of c. 1 940
vi ntage and a "Buck
Rodgers" #709 with
1 950s' streaml i ned
styl i ng, pol i shed
chromed parts,
Teni te plastic
handl es, and sol i d
pl ane physi cs.
Even if the demand for planes was
diminishing, Stanley, Sargent, and
others kept on making them. The planes
were mostly the standard bench-plane
sizes, block planes, and a few specialty
planes such as rabbet planes. Generally
the quality was poor. To keep costs down,
castings were rough, the parts were
poorly finished, and the handles were
plastic or stained wood. These weren't
tools for craftsmen, but for the newly
expanding "do-it-yourself" market.
Stanley even called one of its line of
planes "Handyman" (see the photo at
left on p. 25) . To make some of these
26 C H A P T E R T W O
planes even easier to use, Stanley revived
the old idea of a disposable blade. No
sharpening was necessary-you just had
to put in another "Ready-Edge Blade."
How frustrating it must have been to do
good work with some of these tools.
In amongst these postwar planes there
actually were some good ideas. The most
novel is the "Surform," which is part rasp
and part plane (see the photo at right on
p. 25) . Hundreds of hardened teeth
"plane" the surface in any direction,
without clogging. Then there are the
"Buck Rodgers" smoothing planes made
by Millers Falls, so thoroughly imbued
with 1 950s' style: red Tenite handles,
chrome-nickel finish, streamlined
shaping, and oversized adjuster wheel
(see the photo above). Clearly they were
styled by a talented industrial designer,
but they look as though they work
wonderfully, too.
Although these postwar planes might
look similar to those of the past, they are
as different as the societies that created
them. Hand tools are cultural artifacts
that broadly reflect society overall.
Planes of over a century ago, especially
wooden ones, tell us much about the
inventiveness, skills, and artistic sense of
their makers. The craftsmen who used
the tools valued these skills and the
plane maker's artistry; perhaps this is
what I love about my oid Spiers
smoothing plane. Most new planes no
longer show the special care and talent of
an individual maker, expressing instead
our emphasis on production, uniformity,
and affordability.
If not long ago beautiful planes of all
descriptions could be bought by every
type of craftsman for any imaginable
need, it was because demand created a
supply of good tools. After the turn of
the century demand gradually lessened,
until by World War II portable wood
working tools dominated the market for
new tools. If many of the planes made
since have plastic handles, are poorly
machined and poorly finished, it's only
because until recently this is what the
market was willing to pay for. Those
craftsmen who wanted good tools sought
out the best old tools. They often still do.
While today the demand for planes is
not staggering, it is by no means
insignificant. Every craftsman needs at
least a few planes, and not everyone has
the skills or desire to restore old ones.
Only a handful of makers are still
making a line of common bench planes,
nearly all of which resemble Leonard
Bailey's planes of the 1 870s. While there
is also some demand for more specialized
planes, modern manufacturing methods
often require higher production runs,
exceeding the limited demand.
Fortunately, a number of Renaissance
plane makers have tooled up. For
example, Tom Lie-Nielsen of Warren,
Maine, makes high-quality cast-iron
and manganese-bronze planes based
on Stanley patterns (see Chapter 1 2).
But he doesn't just make copies; he has
re-engineered and improved upon the
originals. In fact, isn't this what plane
makers since the Romans have been
doing all along?
Lie-Ni el sen' s bronze # 1 bench pl ane ( i n the foreground) i s one of
the best-qual i ty pl anes made today. The pl ane at rear is a basi c
contemporary Russi an pl ane of the same si ze with a si ngl e i ron,
more l i ke an early cast-i ron pl ane of more than a century ago.
Modern Stanl ey
pl anes i ncl ude
(from rear) an RB 1 0
rabbet pl ane si mi l ar
to the ori gi nal # 1 0
with a repl aceabl e
edge i ron; a #9Y2A
bl ock pl ane; and a
very new RB5 chi sel
and bl ock pl ane,
al so wi th a replace
abl e edge i ron.
Wood i s no l onger
used on any of
these pl anes.
[ [ [ S T O R Y O F P L A N E S 27
PLANE MEC HANICS
The amount of force required to work each plane is dependent on the angle
and relation of the edge, on the hardness of the material, and the
magnitude of the shaving but the required force is in addition greatly
influenced by the degree in which the shaving is bent for its removal in the
most perfect manner
-Charles Holtzapfel, Turing and Mechanical Manipulation, 1875
I t sounds like a child's joke: What has
a toe, a heel, and a sole, two cheeks, a
mouth, and a frog in its throat? And it's
sliding across the bench toward you
All trades have specific names for things,
and, in thinking about the parts of a
plane, I wonder why many of these
names correspond to parts of our bodies.
Is there any connection between these
anatomical names and the beautiful
heads carved in the throats of early
European planes? I believe we relate
names to parts of our bodies because we
can readily understand them. If I told
you a plane had a toe, a heel, and a sole
and you had never seen one before, most
likely you could imagine a tool shaped
like your foot and right away know
which end was the toe and which the
heel. Even if you already know where
the heel of a plane is, take a minute or
two to familiarize yourself with the parts
of a plane (shown in the drawings on
pp. 30-31 ). Speaking the same language
will help to avoid misunderstandings in
this chapter, which explains how the
different parts relate to the functioning
Shavi ngs are as different as the tools that produce them. Shown here
are transl ucent, gossamer-thi n smoothi ng-pl ane shavi ngs and coarse
scrub-pl ane shavi ngs, barely curl ed and l ooki ng al most as if they were
gouged from the surface.
of a plane, and in later chapters on
tuning and using planes.
Although they have similar parts,
planes come in lots of shapes, styles, and
sizes, are made of different materials,
and have an iron held in various
configurations. Yet one thing planes all
share is the same basic cutting dynamics.
If a plane is essentially an iron secured in
a plane body, then its performance is a
function of certain physical
characteristics: the mass of the plane,
how the iron is secured, how sharp it is,
its pitch or angle to the sole and bevel
angle, the width of the throat opening,
the depth of the cut, and how the plane
is oriented to the cut. Naturally these
factors are all interrelated. For example,
you will see later how skewing the plane
has the same effect as lowering the pitch
of the iron, giving a better cut. This
29
Par ts of a Wood en Plane
Throat
Toe
chapter explains how each of these
characteristics affects a plane's
performance, which will not only help
you understand better how a plane cuts,
but also help you choose the right plane
for the job and tune it to do the best
work possible.
Plane Anatomy
There are three general classes of planes,
each with a somewhat different
anatomy. What distinguishes them are
the materials their plane bodies are made
from: wood, metal (often cast iron), or
some combination of the two, as in
30 C H A P T E R T H R E E
Sal e
transitional planes. The drawings above
and on the facing page show the parts of
a simple bench plane in both wood and
cast iron.
WOODEN PLANES
The wood-bodied plane has a one-piece
body or stock, which is cut into to create
a throat, a mouth, a bed for the iron, and
slots in the cheeks to wedge the iron in
place. On such a plane there is usually a
single handle or tote (to the English, a
"toat") securely mortised or fastened in
the rear of the body. This is usually the
only handle on wooden bench planes,
although earlier planes had a "grip" just
Handl e
or tote
Handl e slot
Heel
Body or stock
back from the toe. On better-quality
traditional wooden bench planes there is
a small button let into the top of the
body at the toe, called a striking button
or start, which is hit to free the iron and
wedge, or to adjust the cutting depth
rather than hitting and marring the
plane stock. Starts can be boxwood,
ebony, or steel-tough materials that can
take the pounding. Some newer wooden
planes have a start set into the end grain
at the heel. Altogether, the wooden
bench plane is a simple design that has
changed little over the past two millennia.
The iron on the bench plane shown in
the drawing is a double iron made up of
Par ts of a Cast - I r on Plane
Lever cap
Cap i ron
Lever-cap
screw
a cap iron bolted to the cutting iron; the
two irons are held in place with a wooden
wedge let into tapered slots cut into the
throat cheeks. Over the years many
wedge designs have been tried to hold
the iron securely in place and allow the
smooth escape of the shavings. Before
about 1760 wooden bench planes would
I ron
Lateral adjustment lever
Body
Rear handl e
or tote
Throat adjustment screw
Throat
have had a single thick iron, as some still
do, wedged in a similar way as the double
iron. Eastern planes use a variation of
this wedging system; they have very thick
and short single irons wedged into place
against a cross-bar, sometimes with
either a wooden or steel wedge that does
some of the same work as a cap iron.
CAST- IRON PLANES
Cast-iron bench planes might look
different from their wooden counter
parts, but the parts are basically the
same. The one-piece cast-iron body has
sides machined square with the sole, a
mouth and a throat that the shavings
pass through, a rear handle and a front
P L A N E M E C H A N I C S 31
knob bolted on, and machined faces
where the frog attaches. The frog, a
separate casting machined to mate with
the plane body and screwed to it, forms
the bed for the cutting iron. Except for
the very earliest bench-plane designs,
most frogs have some sort of adjustment
screw to shift the frog's position. Besides
the cost savings to cast and machine the
plane body and frog separately, an
adjustable frog allows the throat opening
to be fine-tuned by moving the frog
forward or backward.
Often the difference in performance
between one cast-iron plane and another
is directly related to how positively the
frog mates with the plane body to
support and stabilize the iron (see the
sidebar on p. 47). The iron in the cast
iron bench plane shown in the drawing
on p. 31 is also a double iron, but it's
much thinner than those common in
wooden planes. Whereas double irons
perform better in hard-working bench
planes, single irons are usual in other
metal planes such as block and shoulder
planes making light, accurate cuts.
Whether the iron is single or double, a
lever cap locks the iron down against the
frog through a screw that allows for
variable tension.
There is one small but very important
difference between a cast-iron bench
plane and a wooden bench plane: Most
cast-iron bench planes have an adjuster
that regulates the depth of the cut and
the alignment of the iron, whereas few
wooden planes do. We have a stroke of
genius by Leonard Bailey to thank for
this detail (see the sidebar at right). On
the back of the frog are two adjusters.
One is a steel lever with its lower end
engaged in a slot in the iron that pivots
side to side and brings the iron into
alignment with the sole. This is the so
called lateral adjustment. Cutting depth
is adjusted through two parts: an adjuster
32 C H A P T E R T H R E E
P L A N E - I R O N A D J U S T E R S
I
n the middle of the
19th century, with a
growing interest in machines,
invention, and cast-iron
planes, there was a parallel
interest in ways to adjust the
iron more easily. The earliest
adjuster designs were
developed on wooden planes,
most naturally because these
were the planes in daily use.
Lateral adjustment wasn't
difficult-the iron could be
tapped to either side to align
it-but depth adjustment was
trickier and took more care
and a light touch.
Part of the challenge with
wooden planes was coming up
with a design that could move
the iron while it was wedged
in place. Some ideas worked
by first unwedging the iron;
more successful designs
devised new ways to hold the
iron that still allowed it to
slide up and down. Many
designs used some sort of
threaded adjuster attached to
both the plane body and the
iron. While many of these
early adjusters worked, they
seem awkward compared with
the ease of modern adjusters.
With the birth of cast-iron
planes came inventive ideas
for adjusting their irons. One
of the earliest, a Leonard
Bailey design, used a lever
behind the iron with a small
nib that engaged with a plate
riveted to the iron; rocking the
lever raised and lowered the
iron. From here it wasn't a big
leap to an adjuster similar to
ones still commonly used on
block planes, with a wheel
mounted on a vertical post
that raised and lowered a lever
or pin engaged with the iron.
Stanley competitors Union
Tool, Chaplin, Sargent, and
others came up with their
own versions with large gears,
levers that swing laterally
under the iron, or a means to
move the iron assembly on a
carriage via a threaded rod.
By the end of the century
most cast-iron bench planes
were using a version of the
simple and successful Bailey
adjuster that we know today.
Adjuster invention still
goes on today. Primus wooden
planes (see the photo on p. 24)
use an adjuster that looks
simple enough and works well,
but it's almost too complicated
to describe. More interesting
is that they feel their planes
need an adjuster to compete in
the marketplace today.
Earl y adj usters for wooden pl anes l ook awkward to modern eyes.
Shown here are Gl adwi n' s 1 858 patent smoothi ng pl ane (at rear),
whi ch has a brass l ever cam that l ocks and unl ocks the doubl e i ron,
and Worral l ' s patent bl ock pl ane, whi ch adjusts wi th a screw at the
heel of the pl ane.
Sargent' s VBM (Very Best Made) "auto-set" adj uster has a knurl ed nut
that adj usts the depth of the cut and a l arge lever for lateral al i gnment.
Many i nnovative approaches were tri ed for adjusti ng the i rons of cast
i ron pl anes. On Chapl i n' s i mproved patent bench pl anes a large
ni ckel -pl ated lever moves the "saddl e" that hol ds the iron i n or out.
Uni on Tool ' s verti cal post adjuster is somewhat sl ower to adjust than a
Bai l ey pl ane adjuster, but it is extremel y positi ve.
P L A N E M E C H A N I C S 33
A steel toe pl ate
fitted to the toe of a
shop made wooden
smoot hi ng pl ane
makes the throat
adjustabl e for the
fi nest work and
keeps the sol e from
weari ng.
Transi ti onal pl anes are part wooden pl ane and part cast i ron. Thi s
expl oded vi ew shows the number of parts that make up one pl ane,
each i denti cal and i nterchangeabl e wi th parts on si mi l ar pl anes.
34 C H A P T E R T H R E E
wheel mounted on a horizontal post on
the back of the frog and a V-shaped fork
captured by the adjuster wheel. The
adjuster fork passes through the frog and
engages with the cap iron; as the adjuster
pivots, it moves the iron in or out. Some
block planes have a modification of this
same system, with the adjuster wheel
mounted on a vertical threaded post set
into the plane's sole.
Some wooden and cast-iron planes,
a low-angle block plane being one, have
another adjustable feature that's very
useful for refining the cut of the plane:
an adjustable throat regulated by a
movable part of the sole ahead of the
iron (see the top photo at left)' It's handy
to be able to adjust the throat for
different planing jobs-a wide opening
for coarse work and planing thick
shavings and a tightly set opening for
fine work and thin shavings. The
advantage of the movable sole is the ease
with which adjustments can be made; by
backing off a nut or screw on the top of
the plane you can loosen the sole piece
and slide it forward or backward. For
cast-iron planes without an adjustable
throat, the alternative is to loosen and
move the frog, which often entails
removing the iron first. At one time cast
iron toe plates, for an adjustable throat,
or complete iron soles could be bought
separately and fitted to a shopmade
wooden smoothing plane.
TRANSITIONAL PLANES
Although not all that different from
wooden or metal bench planes,
transitional planes have a unique
anatomy. They combine the beech plane
body of a wooden plane with the upper
half of a cast-iron plane. Often they are
mistakenly thought to be transitional in
the sense that they mark a step in the
evolution from older wood-bodied
planes to newer cast-iron planes. In fact,
metal and wood have been combined in
planes since the time of the Romans
(see the photo on p. 1 5). Stanley offered
transitional planes the same year it
started selling Bailey cast-iron bench
planes, recognizing that some craftsmen
preferred the lower cost and sweet
action of a wood sole, along with the
convenience of a metal plane's depth
and lateral adjustment.
The wood body of a transitional plane
is thinner than that of an all-wood bench
plane, but with the same throat and rear
handle. The iron casting that forms the
upper half of the plane contains the
same working parts as a metal bench
plane: a similar frog, mechanisms for
lateral and depth adjustment of the iron,
a lever cap, a double iron, and a front
knob. These planes are preferred by
some for their lightness and easy planing,
but they share the same limitations as
all-wood planes. The sole naturally wears
over time and can warp out of true with
seasonal humidity changes. Early versions
had another problem: The frog screwed
right into the wooden body and would
work loose over time and no longer
support the iron rigidly. A later improve
ment screwed the frog into threaded
bushings set into the plane body.
MATERIALS
Wood has always been an important
material used in plane making, whether
the plane is all wood, primarily cast iron,
or somewhere between the two as in
transitional planes. Beech is the most
common wood, used in all types of
wooden bench and molding planes
because of its stability, toughness, and
density. Some early American plane
makers made planes of yellow birch, a
wood similar to beech, for probably no
other reason than to be different and
distinguish their planes from English
prototypes. More rare are beautiful planes
of apple, boxwood, or bird's-eye maple.
Dense tropical woods make stunni ng and l ong-weari ng pl anes.
Ebony pl anes, such as thi s low-angl e Engl i sh miter pl ane, are relati vel y
uncommon.
These transi ti onal
pl anes were made
by the Gage Tool
Company, of
Vi nel and, New
Jersey, whi ch was
eventually bought
by Stanl ey. Beech
was the standard
wood ( background),
but for a smal l
premi um, appl e
was substituted for
a l onger-weari ng,
more beauti ful pl ane
(foreground) . The
knob and handl e
are rosewood.
P L A N E M E C H A N I C S 35
School boy pl anes were made to be nearly
i ndestructi bl e, either wi th thi ck casti ngs
or made from pressed steel or mal l eabl e
cast i ron.
36 C H A P T E R T H R E E
In coastal towns and colonial
shipbuilding centers, lignum vitae was
the preferred wood for bench planes,
most likely because tropical woods were
regularly shipped to the Colonies
through trade with Central and South
America and the West Indies. Such a
hard and dense wood (the only one that
doesn't float) makes good tools that
stand up to heavy use and wear. Other
exotic tropical woods are also found in
planes: Rosewood, cocobolo, and ebony
have been used for knobs, handles,
fences, and entire planes, such as the
high-end plow planes. These tools are
often further decorated with ivory, brass,
or even silver details. Rosewood, ebony,
and beech have been commonly used to
"infi1l" or stuff within the metal sole and
sides of expensive British and American
wood-and-metal planes (see the photo
on p. 42).
Boxwood i s a hard, long-wearing
wood that has been used in many ways in
plane making. Imported from Turkey or
cut from hedges, boxwood works fairly
easily and is so fine grained that it almost
appears to have none. Small and
expensive specialty planes are sometimes
made entirely of boxwood, although its
chief use has been for the parts of
molding planes or plow-plane fences
subject to hard wear. What has become
known as "boxing" is inlaying boxwood
(or lignum vitae or other hard tropical
wood) where maximum wear occurs
down the length of the sole of molding
planes or where the profile is particularly
fine and fragile. Boxing styles are as
variable as the personalities of the
makers, yet all are replaceable or
repairable when needed. (Boxing is
explained further in Chapter 10, )
Nearly any dense hardwood will make
a good plane body, but for dimensional
stability it is important that it be straight
grained and quartersawn. Look at any
wooden plane and you'll usually find the
growth rings parallel with the sole and
the sides showing quartersawn figure.
Usually the plane blank is oriented so
that the grain gently rises from the heel
to the toe, so that in use the fibers are
smoothed down rather than worked
against (see the drawing on p. 30). Since
many plane makers believed that the
hardest part of the tree is closest to the
bark, this side of the body became the
sole. Sometimes the green plane blanks
were boiled for a day or longer to speed
the seasoning process and bring out the
rich color of the wood. At the very least
the blanks were seasoned for many
years (sometimes as long as eight years).
Seasoning the stock, choosing the right
blank for a particular plane, and
orienting it properly have all been
important parts of the wooden-plane
maker's craft.
Whereas wooden-plane makers had a
variety of woods to choose from, metal
plane makers have historically used only
a few materials. Once the technology of
cast iron had been sufficiently mastered,
it became (and still is) the most common
material for metal planes. The chief
virtues of cast iron are its workability, its
adaptability to many applications, and
its low cost. It has another nice quality
cast iron is porous enough to absorb wax
into the sole for considerably easier
planing. If you've ever dropped a cast-
iron plane you know very well its main
limitation-its brittleness. Drop-forged
and pressed-steel plane bodies are more
durable alternatives to cast iron and
good choices for schoolboy planes and
carpenter's block planes subjected to
rough use (see the photo on the facing
page). Another limitation of cast iron is
that it rusts. To overcome this, Stanley
produced a few lightweight aluminum
planes for a short time between the wars,
but they never became popular.
The sole and sides of early British
smoothing, miter, and panel planes (mid
length bench planes) are made from steel
or gunmetal plates ingeniously and nearly
Stanl ey exper i mented with al umi num for onl y a few years, maki ng pl anes of thi s material
quite unusual and uncommon. Shown here are a Stanley #45, #78, and bl ock pl ane.
invisibly dovetailed together. Rosewood,
ebony, or beech fills the interior space and
forms the throat, bed, front knob, and
handle, with a gunmetal lever cap and
tightening screw. Gunmetal is a
common name for any brasslike alloy, be
it brass, bronze, or true gun metal, so
named for its original use for casting
cannons. Gunmetal is a beautiful bronze
alloy of copper and tin in the ratio of 8: 1
that's harder than iron and is easily cast
and worked. Unfortunately, brass soles
can leave smudges on the planed surface,
so for this reason and added wear
resistance a thin steel sole is often
soldered on. Manganese bronze, an alloy
containing almost no tin but a high
proportion of zinc, has become the
material of choice for many contemporary
specialty plane makers. It has the same
beauty and easy workability as gunmetal,
as well as the nice advantage of weighing
slightly more than cast iron. Since
bronze is not a porous metal, bronze
soles need frequent waxing for smooth,
easy planing.
HANDLE STYLES
Not only does the plane maker have a
wide range of materials to choose from,
but he also has the freedom to shape the
parts to suit his comfort or aesthetic. As
a way to grasp the plane, to direct force to
it, and to steer it, handles are one such
element that takes many forms. They're
as individual as each craftsman or plane
maker, ranging from the functional to
the beautifully sculptural.
The simplest "handle" is nothing
more than a comfortably shaped plane
body that affords a grasp. Wooden
smoothing and block planes are held this
way, as are metal block planes with the
Stanley "Hand-y" feature-oval recesses
milled in the plane's sides for a finger
hold (as shown in the photo of the block
plane at left). Small one-handed planes
P L A N E M E C H A N I C S 37
The si mpl est " handl e" is a comfortabl y shaped pl ane body. The Li ttl e
Vi ctor (foreground) and the Stanl ey #1 01 % (center) are hel d by two
or t hree fi ngers al one. The owner-made handl e added to the Stanl ey
# 1 01 bul l nose pl ane ( rear) provides a pl ace to rest the pal m for
added control .
Hammacher Schl emmer vi ol i nmaker' s pl anes, shown here i n a fitted
case, have detachabl e tail handl es that screw i nto the frog. The tool i n
the background i s a peg shaper, whi ch works l i ke a tapered penci l
sharpener or spoke poi nter.
have rounded knobs, "squirrel tail"
handles, or pistol grips. My favorite block
plane, a Stanley #9%, has a rosewood
ball- tail handle, just comforta ble enough
to grasp and to use the plane one-handed,
or to help balance the other hand on the
front knob. To hold the smallest block
planes, a squirrel-tail handle is the best,
which as a Stanley catalog notes, "just
fits nicely into the palm of the hand."
Pistol-grip handles allow a lot of control
steering the cut, either with one or two
hands, as is common with coachmaker's
planes (see the top photo on p. 217).
Some violinmaker's planes have one
further handle variation-a rou nded palm
grip on a rod that extends well behind
the heel of the plane (see the photo at
right above).
38 C H A P T E R T H R E E
Of all planes, bench planes are the
hardest working and most in need of a
stout handle or a means of getting a firm
grip. An early handle on wooden planes,
if you can even call it that, was no more
than a rounded support behind the
blade that one's hand would stop behind
to push the plane. The other hand woul d
just grab the front stock of the plane. On
later cast-iron planes a low or high knob
was bolted on near the toe for a more
comfortable and surer grip. Gradually
the rear handle became longer and
higher, eventually evolving to the shapely
and comfortable open tote we know
today. For greater strength, the same
style tote is "closed" in what is also
known as a I"handle.
Cast-iron handles, formed as part of
the plane body as in cast-iron plow
planes and the Stanley #45 and #55, are
almost always closed. This gives the tool
good balance, an important attribute of
any handle, and greater strength to
survive hard use. Besides strength
considerations, whether a plane has an
open or closed handle is a matter of
personal choice, assuming there is
adequate room behind the iron for either
style. I don't know if 1 9th-century
craftsmen had small hands or if I have
large hands, but I never seem to be able
to fit more than three or four fingers
comfortably around either style of
handle. This might be an actual
advantage; the odd finger comes in
handy for adjusting the iron's depth on
the fly, and laid along the side of the
plane it gives an added bit of control.
If you look closely at an old cast-iron
bench plane tote, you can't help but be
struck by its beautiful, sculptural shape.
You might also notice that the tote cants
forward toward the throat of the plane.
This subtlety gives an added measure of
control by not only directing the plane
forward but also pressing it downward
into the cut.
Where once these totes and knobs
were commonly rosewood, walnut, or
coco bolo (or aluminum or hard rubber
for replacing broken handles in school
shops), today you'll find beech, stained
maple, or plastic. None of the latter
materials have quite the same feel or
beauty as richly grained rosewood
polished smooth over time, certainly not
plastic, as durable as it is. Furthermore,
plastic handles come one size fits all and
they aren't so easily shaped to fit one's
hand. Whatever your plane handles are
made of, don't be afraid to shape them
for a better fit or to smooth the edges for
comfort. More will be said about tuning
handles in Chapter 4.
The Physics
of Planing
Planes are more than just a collection of
parts fitted together. Clearly some planes
work a whole lot better than others.
Why is this? Why can one plane curl up
shaving after shaving from obstinate
curly maple and leave a surface with an
almost polished smoothness, where
another plane chatters and clogs after a
few uneven planing strokes? Certainly
it's a matter of tuning and a certain
harmony among the parts, a sharp iron,
choosing the right plane for the work,
and knowing how to use it. But it's more
than this. Some planes just have physics
in their favor.
CHIP FORMATION
The dynamics of the cut is fairly basic
physics. The plane's cutting iron contacts
the wood, driving a shaving into the
throat that curls and breaks against the
cutting edge of the iron (and against the
cap iron, too, if the plane has one). Every
part of the plane in contact with the
shaving affects the physics: the sharpness
of the iron, the size and smoothness of
the throat opening, the pitch of the iron,
and its bevel angle. Understanding
some of the subtle aspects of this physics
will really help in fine-tuning your
planes, or it might inspire you to build
a "better" plane.
A plane iron is really no different
from a chisel; the plane body supports
the iron in a way that allows good control
of the cutting action. Imagine driving a
chisel into a block of wood along the
grain: Not only will the fibers be cut, but
some splitting will occur as well. Areas
where the grain splits out (otherwise
The cl osed " 0"
handl e of t hi s rare
Mi l l er' s I mproved
Joi ner' s plow pl ane,
i n gun metal with
beauti ful fl oral
decorati on, is
formed as part of
the cast i ng.
P L A N E M E C H A N I C S 39
Cutti ng D ynam i c s
FI NE THROAT, FI NE SHAVI NG
Primary
bevel
angl e
Pitch
of iron
The front of the throat
pushes down on the
shaving as the iron
levers it up.
WI DE THROAT, COARSE SHAVI NG
Iron Support too far
ahead of cut
The front of the throat cannot support the shaving,
so some splitting and tea rout occurs.
known as tea rout) are rough; cut areas
are considerably smoother. The physics
of a plane is simply an attempt to control
the splitting in favor of cutting for a
smooth final surface.
The quality of the cut is affected
by the hardness of the material or its
resistance to being cut, the cutting angle
or pitch that the cutting edge makes
with the surface, the direction of the
wood grain, and the thickness of the
shaving. If this same chisel had an acute
edge similar to a knife, the wood was
straight grained and easily worked, and a
fine rather than a coarse shaving was cut,
40 C H A P T E R T H R E E
then very little splitting would occur and
the resulting surface would be quite
smooth. Working with the grain, any
splitting ahead of the cut would be above
the final cut surface and be of minor
significance. Also, less force is needed to
cut with an iron with a thin edge profile.
In theory, this is how a low-angle plane
or spokeshave works.
The problem comes in cutting
anything other than well-behaved woods
with the grain, which is where a plane
has distinct advantages over a chisel.
Forcing the shaving into the throat of the
plane causes it to be curled and
repeatedly broken in a levering action
Fi ne shavi ng
Coarse shavi ng
that limits potential tearout. The
drawing above shows the cutting edge
lifting a chip, forcing it upwards, and
breaking it against the forward part of
the throat as this part of the sole exerts
downward pressure. Some splitting is
bound to happen when planing against
the grain; the best you can do is keep the
tea rout as fine as possible. A sharp iron,
cutting a thin shaving, and a tight throat
will all help. This makes it easier to
understand why a wide throat (caused
by wear or inattention) often does not
give good performance-the chip is
supported too far ahead of the cut and
too much splitting goes on. Of course,
T h e Ph ysi c s of S ke w i ng the C u t
STRAI GHT CUT
SKEW CUT
Force
Small force at right
angles helps shear the
fibers.
for rough work and planing thick
shavings, a wider throat is necessary.
Effectively curling and breaking the
shaving depends on more than just the
width of the throat, but also on the
inclination of the iron to the sole, or
pitch, and the presence or absence of a
cap iron. For hard or figured woods a
steeper pitch is necessary for good
results. The steeper the pitch, the more
abruptly the shaving is curled and,
assuming the fibers are pressed
downward by the front of the throat,
splitting out ahead of the cut is less
likely. But the pitch of the iron has a
dramatic effect on the force required to
drive the plane; the steeper the pitch, the
more force needed. This can be more
easily understood by comparing the force
needed to cut a shaving with a knife edge
at a low angle to the surface (a thin
wedge at 25 pitch) to the force needed
to cut with a chisel held at a high angle to
the surface (a thick wedge at 45 or
higher pitch).
A cap iron (also known as a chip
breaker) presents a steeper angle than
the pitch of the cutting iron and helps
curl and break the shaving, but at the
cost of slightly greater resistance. The
closer the cap iron is set to the cutting
edge, the more effective the cap iron.
Most important is that the leading edge
of the cap iron lie completely flat against
the cutting iron to help stabilize it and
not allow any shavings to lodge between
the two and clog the smooth escape of
new shavings.
SKEWING THE IRON
Skewing the cut is one way to have your
cake and eat it too, so to speak-good
performance and reduced cutting force.
Rotating or skewing the plane at either a
Pitch
- ----- -
Effective
pi tch
/
/
Skewing the iron
lowers the
effective pitch.
slight or great angle noticeably improves
the cutting dynamics. Three things
happen: The effective cutting angle is
lowered, the iron presents a smaller
profile to the cut so there is less
resistance, and a slicing force is added to
the cut (see the drawing above).
Skewing is an incredibly effective
strategy, especially for beginning a stroke
smoothly. Skewing in one direction will
often make a very noticeable difference
over cutting the opposite way, especially
in areas of swirled figure or knots.
Increasing the skew of the plane can
sometimes help, too, although with too
much skew the plane is making only a
narrow cut. At this angle the dynamics
can also be so different that with some
woods you start to get some tea rout. The
key is to experiment.
P L A N E M E C H A N I C S 41
Characteristics
that Affect Plane
Performance
Once you've grasped the basic physics,
you can better understand the
characteristics of each plane that affect
the way it cuts. Moreover, these
characteristics are all interrelated: It
doesn't matter what the pitch of the iron
is if the iron can't hold a good edge, or
how good the edge is if the iron vibrates
and chatters under cutting pressure.
Subtle changes in the plane's physical
characteristics-using a heavier iron, a
different bevel angle, or adding a
microbevel-will often make a noticeable
difference in performance. Being aware
of the contribution of each of these
factors will make it easier to understand
how to tune planes, give you greater
insight into ways to alter any plane, and
help you decide which plane to buy for a
specific need. One of the easiest factors
to understand is how the mass of the
plane affects the way it cuts.
MASS
When it comes to the plane's mass, all
things being equal, a heavier plane is
more stable, better able to support the
iron and dampen cutting vibration, and
able to cut a lot more smoothly. Taken to
the extreme, we would all want planes
about as heavy as we could comfortably
lift, cast from pure kryptonite or some
other incredibly dense space-age
material. Such planes might work
amazingly well, but we'd get pretty tired
after a few minutes. What's important is
to balance adequate mass for good
functioning with how the plane feels
during extended use.
Where the mass is balanced within
the plane is every bit as important as
how heavy it is. I am really conscious of a
42 C H A P T E R T r I R E E
Thi s beauti ful Engl i sh shoul der pl ane has a gunmetal body i nfi l l ed with mahogany, whi ch adds
mass to the pl ane for superi or performance.
plane's balance when raising it with one
hand at the end of the stroke (as the
other hand clears the throat of shavings).
A casting heavier toward the toe, or a
tote further to the heel, and the balance
doesn't feel right. After a century of
refinement, Bailey-pattern cast-iron
bench planes strike the right balance
between weight, where the weight is
distributed, and the placement of the
tote and knob. Although much lighter
overall, most wood-bodied planes have
the same fine balance gained by
generations of refinement.
The mass of the plane relates directly
to its inertial stability-its ability to
maintain momentum as grain changes
resist the cut. A plane cuts more
smoothly with continuous and
consistent speed, which explains why
the longer bench planes perform well,
often just because they are heavier. A low
center of gravity is another nice virtue, to
help the plane hug the surface.
Mass has historically been added to
planes in many ways. One way is to cut
the plane body from naturally heavy
materials, such as dense tropical hard
woods (see the bottom photo on p. 35) .
Using cast iron, steel, or manganese
bronze can make a plane heavier still.
Thicker castings can add even more mass
and still keep the center of gravity low.
But the best way to add mass is the oldest
and the most time-consuming
construction method that yields planes
beautiful to look at and use: infilling a
cast-iron, steel, or gunmetal body with
rosewood or some other heavy and dense
wood (see the photo above). Some of the
earliest Roman planes were made in this
way, as are traditional British miter,
shoulder, smoothing, and panel planes.
Overall they're about double the weight
of similar wood-bodied planes and, other
things being equal, perform twice as
well, too.
A heavy cap iron and lever cap add
little to the overall weight of a plane, but
because they are right at the heart of the
cutting action, their contribution can be
important. A beefier cap iron is more
likely to be rigid and better able to
support the iron, especially the thin
irons common on most bench planes.
Similarly, a heavy lever cap or wedge is
better able to help resist the same
stresses as it locks down the iron.
SMOOTH AND
CORRUGATED SOLES
Although less massive than cast-iron
planes, wood-bodied planes have always
had a natural advantage with their sweet
action of wood upon wood. With a bit of
wax on their soles, they work with an
ease that is quite wonderful-I' m sure it's
a factor in their enduring appeal. Waxing
the sole of cast-iron planes (except for
jointers or planes cutting surfaces to be
glued) gives nearly the same satisfying
feel . Many early cast-iron plane makers,
being the tinkerers they were, felt they
had to try ways to reduce the friction on
the sole even more to make the work less
tiring and their planes more competitive
with wooden planes.
One of the earliest ideas was to inlay
dovetailed strips of rosewood down the
length of the sole (as shown in the top
photo at right). One innovative maker
milled zigzags down the sole's length,
another cast large holes in the sole, and
still another cast his name in a pattern of
raised letters (see the bottom photo at
right). Stanley tried corrugations, long
grooves milled down the sole that started
and stopped just shy of the heel, throat,
Corrugated sol es coul d serve as adverti si ng, too, as on thi s mi d- 1 870s
pl ane by the Bai l ey Tool Company of Woonsocket, Rhode I sl and.
Thi s company was started by Sel den Bailey, not t he better-known
Leonard Bai l ey.
Each of these t hree
early patented cast
i ron pl anes has a
different sole desi gn
to reduce fri cti on:
from the back,
Steer' s rosewood
strips dovetai l ed
i nto the sol e;
Rodi er' s wavy
corrugati ons; and
Bi rdsi l l ' s smooth
pl ane wi th dri l l ed
hol es.
P L A N E M E e l I A N I C S 43
A Japanese l ami nated i ron and cap iron ( bottom) is consi derabl y
more massive than the standard Stanl ey thi n iron (center) and the
thi cker i ron typical of ol d wooden bench pl anes (top).
and toe. Such planes were sold with the
idea that they might work better in
pitchy woods and the corrugated sole
would eliminate any "suction" increasing
friction. Another amusing explanation
was that the corrugations were meant to
hold wax and thus would constantly
rewax the sole under use.
I've never had much use for corrugated
soles and find them no different in use
than a smooth sole. Moreover, small
surfaces being planed can sometimes
fall into the corrugations. Others must
have agreed with me; corrugated planes
are far less common, even though new
they cost no more than smooth soles.
Because of their rarity, corrugated planes
44 C H A P T E R T H R E E
sell for a premium today. Perhaps their
only advantage is the ease with which the
sole can be lapped flat.
PLANE IRONS
A more massive plane iron has the same
positive effect on performance as greater
overall mass of the plane body. In most
bench planes, it's easy to substitute a
heavier iron for a difference that will
amaze you. Eastern planes take this
concept to the extreme; the wooden
plane body is relatively light with a short
massive iron-quite the opposite of
traditional Western bench planes.
Since the iron is taking the full force
of the cut, its ability to remain stable has
a direct effect on the way the plane feels
while cutting and on the quality of the
cut surface. Driving the iron into the cut
changes the pressure on the cutting edge,
which can cause it to distort and vibrate.
Changes in the grain direction in figured
woods, the naturally variable grain in any
board, the size of the shaving, or working
the plane at a skew all affect the pressure
upon the iron. Of course, a dull iron
increases the pressure, too. The thicker
the iron, the stiffer it is and the better
able it is to resist flexing and vibrating.
The invention of the double iron was
a major advance in the evolution of the
plane. The curved end of the cap iron
not only helps curl the shaving better
than a single iron alone, but the cap iron
also supports the cutting edge. In the
days when plane irons were commonly
thick and heavy, a cap iron was less
important because the iron was rigid
enough on its own. But when Bailey and
Stanley introduced a very thin iron
(presumably because it was easier to
grind and hone), a well-fitting cap iron
became very important for best results.
Before thin irons became standard
issue, two versions of a thick iron were
common: parallel or gauged irons and
tapered irons. As the name implies, a
parallel iron is of equal thickness from
end to end. Today's thin irons are
parallel, too, but only about one-third
the thickness of the older irons. Tapered
irons have a distinct taper from a thick
cutting edge to a thinner top end.
Functionally, there is no difference
between parallel irons and tapered irons.
There is one subtle difference, however;
over the decades of grinding and honing
the tapered iron gets shorter and the
cutting edge advances into a thinner
section of the iron. This has the same
effect as gradually widening the throat.
Japanese irons are typically tapered
and, as with older Western irons, are
made by forge-welding a steel cutting
edge to a wrought-iron or mild-steel
blank. Both materials are heated red hot
and hammered together at the anvil.
Originally this method in the West was
born out of economy, because quality
edge steel was usually imported and thus
more expensive and less available than
native wrought iron. But there is an
added advantage to laminated blades.
The wrought iron has a natural ability
to dampen cutting vibration and makes
for a stronger iron by supporting the
harder and more brittle cutting edge.
Because of the support the mild steel
gives, laminated irons can be harder
(Rc62 on the Rockwell hardness scale)
than irons of high-arbon cast steel
(Rc58-60) or a modern alloy, and hold a
better edge as a result.
The hardness of the cutting edge has a
major effect on its durability, how easily
it can be sharpened, and its optimum
bevel profile-certainly very important
characteristics. Hardness is always a
balance between a hard, long-lasting edge
that is also brittle and likely to chip
when forced into a knot or particularly
unyielding grain, and a softer edge that
has the necessary strength but doesn't
sharpen quite as keenly and dulls more
quickly with use. The harder the steel,
the larger the bevel angle necessary to
support the cutting edge. Honing a
steeper microbevel or honing a back
bevel are two ways to create a more
durable edge and improve performance
(see Chapter 4).
How do you go about choosing a good
plane iron if you need one? Fortunately,
few of us will wear out an iron in our
working lifetime; if we do, it will
probably be a common size for a bench
plane. Certainly there are irons available
in many modern steel alloys, each with
slightly different working characteristics.
With modern steelmaking processes and
sophisticated means of hardening and
tempering, plane irons have probably
T H E Q UA L I T Y O F A N I R O N
T
he search for the ideal
steel for plane irons has
been a difficult one. Iron is a
very complex material. Even
though smelting iron and
forging it into tools has been
known for 3,000 years, it
wasn't until the 1 8th century
that steelmaking was
mastered. Only a little over a
century ago with the invention
of the Bessemer process was
steel finally available in both
large quantities and consistent
quality.
Two problems plagued
early attempts at smelting iron
and refining it into steel:
getting rid of the natural
impurities in the iron and
achieving the high heat
necessary for making steel.
Also necessary is a carbon
content between 0. 5% and
1 . 5%, which gives the steel the
magical ability to be hardened
and tempered. But as the
carbon content drops, higher
and higher temperatures are
needed, requiring sophisti
cated furnaces and vessels to
contain the molten iron.
Cast steel, a superior tool
steel, was first made in 1 742
by Benjamin Huntsman, a
clockmaker searching for a
method of making steel for
springs of absolute regularity.
He took pieces of blister steel
(Swedish iron low in
impurities heated in charcoal
to absorb some carbon),
melted them in a clay crucible,
and cast the steel into bars.
This steel had a more
consistent structure, perfect
for forging into edge tools.
Initially only small amounts
could be made at a time, so it
was expensive. Because of this,
many early plane irons and
edge tools have a noticeable
weld line where an edge of
cast steel was forged to a
wrought-iron blank. As the
cast-steel-making process
improved, costs came down.
Later irons were entirely cast
steel and were so stamped to
mark them as of high quality.
There is no equal to cast
steel for its ability to take and
hold a keen edge. A modern
plane iron is almost certainly a
steel alloy-some combination
of carbon steel and a small
percentage of tungsten,
vanadium, chromium, or any
of a half-dozen other
elements. Alloying elements
are added for many reasons: to
increase the steel's hardness
and hardening ability, wear
and shock resistance, tensile
strength, or resistance to
corrosion. It is an incredibly
complex and subtle process,
where slight changes in
composition affect the quality
of the finished steel. Add to
this the uncertainty of the
hardening, quenching, and
tempering of the iron and you
can easily see why the quality
of an iron is often a matter
of luck.
P L A N E M E C H A N I C S 45
Cutti ng Geometr y f or Benc h Pl anes
( Bevel Down)
Cutting angl e
or pi tch
45 Common pi tch
Cl earance angl e
(pi tch mi nus
bevel angl e)
30 effective bevel
I ron
become more consistent, but no better
than a good cast-steel iron of one
hundred or more years ago.
Plane-iron metallurgy must involve an
element of magic. Some irons are just
excellent-they sharpen easily and hold a
keen edge. Other irons range from
adequate to useless. Two irons that look
identical might sharpen and hold an
edge quite differently. This is due in part
to the differences in the way an iron is
made today-whether it is stamped out
of a sheet of steel or carefully hammered
and forged by craftsmen who worked a
lifetime to learn this subtle art. I always
look for older cast-steel irons (usually
stamped "warranted cast steel"), and
the thicker the better (see the photo on
46 C H A P T E R T H R E E

5 mi crobevel
A standard bevel
angle is 25 to 30 for
a fine and durable
edge. This leaves an
ample clearance
angle between 15
and 20, or more for
higher pitches.
25 main
bevel
A microbevel creates a more durable
cutting edge.
p. 1 8). Two of my favorite irons were
bought new on a whim at a hardware
store in Singapore for less than $3 There
is no easy answer as to where to find a
great iron, but you'll certainly know it
when you do.
Bedding the iron
Whether thick or thin, double or single,
all irons need to have stable support
from the plane body to cut well.
Supporting the iron is the function of
the bed or frog. On most planes the bed
is cut forward of center so that there's
more of the body mass behind and
supporting the iron. On wooden and
transitional planes the bed is cut right
into the wood body; cast-iron planes
have a separate frog cast and machined
and then screwed to the sole of the body
casting. The bed of wood-bodied and
transitional planes is cut at a consistent
angle right to the bottom of the sole,
which gives the iron support over its
whole length and helps dampen
vibration. Any problems occur when
the bed is not true or is warped in such a
way that the iron doesn't sit flat and get
full support.
Two-piece frogs have their own
advantages and disadvantages. I f the
casting and finishing are done well, the
bed is a true surface and will probably
stay flat. Before it is screwed firmly to
the sole, the frog can be slid forward or
backward to fine-tune the throat opening.
Better planes allow for adjustment of
the frog wi thou t removing the iro n,
which is a definite advantage. Any
weakness in the system comes from the
rigidity of the connection of the frog to
the sole. The larger the surface area
between the two parts, the more stable
the connection. This is clearly seen in the
difference between Stanley's Bailey line
of bench planes and the top-of-the-line
Bed Rocks (see the sidebar on the facing
page). Metal frogs have one further
drawback; the bed is not a consistent
angle right to the sole unless the frog is
set in one exact position, which works
counter to moving it to adjust the throat.
This problem is discussed further in
Chapter 4 (see pp. 57-61
Pitch and bevel angle of the iron
The pitch of the iron is the angle it
makes with the sole; the bevel angle is
the angle ground and honed into the
cutting edge of the iron (see the drawing
above). The two characteristics are
separate but related. The pitch is often a
given-some planes are high angle, some
are low angle, and most fall between the
two. The bevel angle is variable within
B E D R O C K P L A N E S V S . B A I L E Y P L A N E S
W
hen Stanley designed bench planes-they even
a new line of premium looked the same-except for
bench planes, they introduced one important improvement:
them with typical bravado, The frog of the Bed Rock was
declaring the Bed Rock "the greatly refined. Not only did
best plane ever made." And the new frog mate with the
they were right; Bed Rocks sole over a wider area milled to
were the best bench planes close tolerances, but it also
Stanley or any of its fitted into a groove machined
competitors ever made. to receive it. This eliminated
Although out of production distortion or potential
by World War II, today they misalignment between the
are eagerly sought after by parts and resulted in a frog
collectors and users alike. that was securely bedded to
Bed Rocks might have been provide rigid support to the
in production as early as 1 895, iron. The plane worked a lot
but they first show up as a better because of it.
new product in catalog #28 Bed Rocks soon had
( 1902). Initially there was another improvement.
little difference between the Initially the frog was secured
Bed Rock and Bailey line of to the plane with bolts, just as
Bed Rock pl anes were made i n a range of si zes from #602 to #608,
with flat or corrugated sol es.
it still is in the Bailey line. involved improvements to
With the bolts loosened, a bench planes that first
fine-threaded captured nut appeared in Bed Rocks. Still,
behind the frog adjusts the Bed Rocks were very similar
frog forward or backward. to Bailey planes; they shared
After 1 91 1 Bed Rocks used a some of the same parts and
more secure clamping system were about as heavy. To
with two pins through the further distinguish their Bed
frog into the sole. Each pin has Rock line, after 1 91 4 Stanley
a cone-shaped dimple in its squared off the tops of the
side. As the two screws with sides and used a higher front
tapered ends behind the frog knob. Numbered #602
engage with the dimples, the through #608 (a # 1 size was
pins are drawn tightly down. never made), Bed Rocks
By just backing out the screws, could be bought with flat or
the frog could be moved corrugated soles. The rarest
without first removing the of all is the #602C
iron as it would need to be in a (corrugated), but the other
Bailey plane. sizes can be found and are
Many of Stanley's patents well worth the search.
in the early 20th century
The Bed Rock frog ( l eft) was an i mprovement on the Bailey pattern
frog ( ri ght). It has a l arge, accurately mi l l ed bear i ng surface, a groove
to locate the frog, and two l arge pi ns to secure i t.
P L A N E M E C H A N I e S 47
S TA N L E Y S WE E T H E A RT T R A D E M A R K
B
ecause trademarks are
apt to change over time,
they are useful for both tool
collectors and historians as a
means of dating manufactur
ing or ownership changes. One
such trademark stamped on
some of my plane irons had
always piqued my curiosity: an
"S. W. " surrounded by a round
heart. Just above the heart is
the word "Stanley" outlined
by a rectangular box.
steel. Stanley Rule and Level
was manufacturing its well
known line of carpenter's
and mechanic's tools, rules,
and levels. Stanley Works
started using the heart on its
hardware line in 1 91 5 to
honor William Hart,
president of the company
from 1 884 to 1 91 5. It wasn't
until after the merger of the
two companies that the
combined trademark was
stamped on plane irons, and it
continued to be used until
1 934. Today some collectors
buy only tools made during
this brief period, creating
demand at the yearly sale of at
least one dealer where every
thing is Sweetheart vintage.
This is the so-called
"Sweetheart" trademark first
used in 1 920 to commemorate
the merger of the Stanley Rule
and Level Company into
Stanley Works. Stanley Works
was a huge manufacturing
company, producing a line of
goods from hardware to bulk The Sweetheart trademark, shown with the catal og announci ng the
acqui si ti on of Stanl ey Rule and Level by the larger Stanl ey Works.
limits, depending upon the hardness
and other characteristics of the iron, and
how the iron will be used. Generally the
more acute the bevel angle, the more
easily the iron will penetrate and cut,
but at the risk of a more fragile cutting
edge that can chip. The more blunt the
bevel, the stronger and more durable
the edge, but also the more resistance to
the cut. Depending on the bevel angle
and the pitch, some planes will cut
hardwood with excellent results, whereas
others will work softwoods more easily.
Small differences in either can be quite
noticeable.
48 C H A P T E R T H R E E
Most bench planes have a 45 pitch
(known as common pitch), which is a
compromise between good all-around
performance and relatively low cutting
resistance. The drawing on p. 46 shows
typical cutting angles at this pitch with
the bevel down and the iron sharpened
at 25 with a 5 microbevel. Lowering
the pitch has the advantage of easier
cutting (a finer edge "wedge"), but unless
the throat is very tight or the wood easily
cut, some splitting rather than all cutting
of the fibers is going to happen. For
highly figured or hard woods where
tearout is a concern, a higher pitch of
50 (York pitch), 55 (Middle pitch), or
60 (Half pitch) works noticeably better.
The higher pitch curls and breaks the
fibers more abruptly before they split.
For common-pitched bench planes, the
effective pitch or cutting angle can be
raised by honing a back bevel onto the
iron (see the top drawing on the facing
page). Unfortunately, a disadvantage of a
higher pitch is that the cutting edge will
also drag more and cut with a scraping
action that can heat and dull the iron
more quickly.
So far in this discussion we have been
looking at pitch and bevel angles for
cutting along the grain of the board. The
mechanics for cutting end grain are quite
different (see the bottom drawing on the
facing page). When cutting the ends of
the wood fibers, a low angle theoretically
works the best. Tearout is much less of a
problem, as is concern about curling the
shavings, because end-grain shavings are
naturally weak and break apart
themselves. The lower the cutting angle
and the lighter the cut, the more easily
the end-grain fibers will cut, rather than
deform and break. This is the physics of
low-angle planes. Commonly without a
cap iron and with the iron bevel up, low
angle planes work well for more than just
end grain, especially if they have an
adjustable throat.
The limiting factor with low-angle
planes is the bevel angle of the iron.
Again it comes down to edge durability
versus the easier cutting of a fine bevel.
Good irons can be beveled at 20 and
possibly even a few degrees less without
risk of chipping the edge. Assuming the
pitch of the body is a given, the only
other way to improve performance
further is to back-bevel the iron 5 or so.
This reduces the clearance angle and
further reduces the cutting angle, while
still keeping the overall bevel angle at 20 .
While back bevels are quite useful,
I find that I rarely hone my irons with
them. By the time I learned and
understood the technique, I had already
collected and tuned an assortment of
high-angle planes that worked extremely
well. I use scrapers often, too. With no
new bench planes available with a pitch
above 47Vzo, back bevels might make the
difference in some woods between a
smooth or torn-out surface. If I had a
limited number of planes to work with,
I would certainly back-bevel the iron on
a heavy smoothing plane and keep it
handy for when nothing else seemed
to work.
Bac k Bevels
Cutting
angl e
Clearance
angl e
Back-bevel
angl e
Effective
A 5 back bevel raises
the effective pitch 5;
the major bevel angle
remains unchanged.
C u tt i ng Geometr y f or Low- Ang le
B l oc k Pl anes ( Bevel U p )
Cutting angl e
Clearance
angle (equal
to the pitch
of the iron)
1 2 bed
angl e
32
cutting
angl e
A 20 pitch and 25 bevel
angle make the effective
cutting angle 45-no different
frm a bench plane.
For low-angle planes tuned to slice
end grain, a 12 bed angle and a
fine bevel of 20 give an effective
cutting angle of 32-a noticeable
difference.
P L A N E M E C H A N I C S 49
TUNING A PLANE
But before you come t use your planes, you must know how to grind, and
whet them, for they are not fitted when they are bought, but ever
Workman accomodates [ sic] them t this purpose, as if it be an hard wood
he is t work on, he grinds his basil t a more obtuse angle, than he would
do for soft wood.
-Joseph Moxon, Mechanick Exercises C3rd. edJ, 1703
Baning with a well-tuned plane can
be one of the most su blime pleasures
of working wood. And tuning a plane
isn't all that difficult. Anyone who
works with wood has the practical skills
necessary; what is often missing is the
information about what to do and how
to do it.
Every plane needs tuning sometime.
Just because a plane is new doesn't mean
that the sole is flat or that the parts were
properly adjusted into harmony at the
factory. You expect that the iron needs
sharpening, but when you start
checking, chances are you'll find other
parts that need tuning to achieve that
smooth performance you're striving
for. Just because a plane is old and well
used doesn't mean it's tuned either.
The craftsman who owned it before you
might not have known any more about
tuning than you do. And planes don't
stay in tune forever. If you're lucky, the
plane just needs a thorough cleaning and
its iron ground and honed. It's more
likely it will need a few hours of work
some rainy day.
Some planes are going to be a
challenge to tune-every aspect is going
to need attention. No matter what
Pike sharpeni ng stones, made by Pi ke Manufacturi ng Co. of Pi ke
Stati on, New Hampshi re, were desi gned to be carried i n a tackl e box
or tool box for touchi ng up pl ane i rons.
condition your plane is in, I suggest you
start at the beginning and check and
tune the parts as they are presented in
this chapter: Tighten and shape the
handles; check and flatten the sole if it
needs it; take the frog apart, flatten the
bed, and become familiar with adjusting
the throat by moving the frog; grind,
hone, and flatten the back of the iron;
and fit the cap iron and lever cap to the
iron. The work can be tedious, but none
of it is hard, and the results will last a
long time. Even a little thing like
smoothing a handle will be felt every
time you pick up your plane.
51
Tuning Handles
Tightening and shaping the handles i s a
good place to start tuning for a quick
sense of accomplishment. The handles
that usually need attention-the rear
tote and the front knob-are those on
Bailey and similar bench planes and
transitional planes. Nothing is worse
than a tote that wobbles around as you
try to steer the plane down a board.
The loosening problem arises from
the orientation of the tote's grain
(parallel to the sole). Although the grain
orientation does ensure a strong handle,
it makes it prone to loosening as the
wood shrinks. A steel rod within the tote
secures it to a boss cast into the plane's
body (see the photo at right). The
Handles that are cut as an extensi on of the i nfi l l , such as this beauti ful tote on a Norri s smooth
ing plane, never come l oose. I n the smal l er Engl i sh bul l nose rabbet plane i n the foreground,
t he wedge extends t o form a secure handl e.
52 C H A P T E R F 0 U R
Handl es on Bai l ey
type bench pl anes
are secured to the
body with threaded
rods. The easi est
way to ti ghten a
l oose tote or knob is
to shorten the rod or
to add a shi m under
the cap nut.
natural swelling and shrinking of the
wooden tote work against the rod in
much the same way that a wooden
handle eventually comes loose in a
hammer head. The most secure totes are
attached with an extra screw through
their base or have some other means of
alignment besides the threaded rod.
Fortunately, the remedy for a loose
tote is a simple and reasonably
permanent one. The steel rod is threaded
on both ends; one end screws into the
body, and the other has a cap nut that
screws down into a recess in the top of
the tote as it threads onto the rod. You
can try snugging up the nut, but chances
are this won't do the trick: Usually the
nut screws to the end of the threads and
the tote is still loose. Instead, I either
grind the steel rod 's in. or so shorter or
shim the nut with a small steel, brass, or
leather washer. If there is an additional
screw in the tote's base, tighten this up,
too. Should you ever need to repair a
cracked or broken handle, disassemble
the handle, clean the joint, and then glue
it together with epoxy.
The front knob rarely comes loose,
because the grain runs along its length in
a strong and stable way. If the knob
loosens and tightening the bolt that
secures it doesn't help, you could try
shortening the bolt slightly or shimming
under the nut as for the tote.
Loose handles are less of a problem
on wooden bench planes. The tote is
usually firmly mortised into the body
and secured with a screw, a bolt, or pegs.
Most wooden bench planes have no front
knob. One type of wooden plane you'll
never have a problem with is one where
the tote and body are cut from the same
stock, as on better molding planes,
tongue-and-groove planes, and British
smoothing planes where the tote is an
extension of the infill (see the bottom
photo on the facing page).
As part of the tuning process, I also
recommend shaping the handles to fit
your hand. Part of my love of old tools is
that the handles feel wonderful-I can't
resist the silky feel of polished rosewood
or beech, carefully shaped and finished.
The grip is so comfortable that I forget
about holding the plane and concentrate
instead on using it. New totes are much
squarer, rounded only ever so slightly.
There's little chance that you'll weaken
the tote or knob by shaping, so go at it
with a rasp, file, or scraper. On new
handles I always like to strip off the
varnish finish while I' m at it, but this is
a matter of personal taste. Round all the
edges until the handles feel just right,
and then wipe on a coat of tung oil or
paste wax.
Flattening the Sole
There i s no universal rule that planes
must have perfectly flat soles to work
well; in fact, there is a whole tradition
that believes just the opposite. Eastern
craftsmen regularly shape the soles of
their planes in a very shallow, wave-like
pattern with special scraping planes, by
relieving some of the wood between the
toe and throat and heel and throat. I am
less familiar with this tradition, but I do
know that relieving the sole doesn't
Check the flatness
of the sale wi th a
straig htedge.
affect the way the plane works and
makes truing the sole easier. The longer
the plane, the less critical it is to have it
flat along its entire length. What's
important is knowing where the sole
needs to be flat and true.
There are two aspects to the "flatness"
of the sole: its truth down the length and
across the width and any potential twist
or winding along the length. Before you
start lapping the sole, use a straightedge
and feeler gauge to test how flat the sole
really is. Hold the plane upside-down
up to a window or bright light with an
accurate straightedge against the sole and
sight along the joint between the two
(see the photo above). The faintest hair
of light is somewhere around 0.001 in.
well within acceptable tolerances. Where
there are larger gaps, try different
thickness feeler gauges to get an idea of
how much of the sole you'll need to lap
away. Also flip the straightedge end for
end and use the opposite edge to see if
there is any variation in your straightedge
that might be misleading you. On used
T U N I N G A P L A N E 53
Si ght across a pai r
of wi ndi ng sti cks to
detect any twist i n
t he sol e.
planes there's a good chance that the sole
is worn just ahead of the throat and at
the toe and heel. The area in front of the
throat wears from the friction of
pressing down the wood fibers as the
shaving is forced through the throat.
While a totally flat sole is not
absolutely necessar, having one without
any twist is a must. No plane will work
accurately if it rocks from side to side on
a twisted sole. Check the sole for twist by
sighting across a pair of winding sticks,
54 C H A P T E R F 0 U R
as shown in the photo above. (For more
on using winding sticks, see the sidebar
on p. 101. )
Even the soles of new planes need
tuning. One explanation I've heard for
the poorer quality and warped soles of
modern cast-iron planes is the use of
inferior cast iron-some of it recycled.
Others claim that the fresh castings need
to be "seasoned" just as wood does before
the sole is milled flat, and more care
could be taken with the milling, too.
Even with virgin cast iron, I' m sure that
at the height of Stanley production
some of its planes were sold without
totally true soles. It's easy enough to
check the sole as part of tuning each
plane, and every few years to check the
ones that see a lot of use. Cast iron, steel,
and bronze do wear, especially when
planing hardwoods.
CAST- IRON SOLES
Flattening a cast-iron sole can be tedious
work. One solution is to take your planes
to a machine shop, which is easier than
hand lapping but a lot riskier. The
biggest risk is that too much will be
taken off the sole and the whole plane
body will be cut unnecessarily thin
around the frog or the throat will be
widened. Since planes are not tools that
most machine shops are familiar with,
take extra care explaining what you
want, or better yet work with them.
A far safer (but slower) method is to
lap the sole on a lapping table, which can
be as simple as a few sheets of sandpaper
taped to a piece of plate glass , +in. thick
minimum) or a flat surface like the bed
of a jointer or a table-saw top. Silicon
carbide or aluminum-oxide sandpaper
works well. For a sole that needs a lot of
work, start with 80 grit and work up to
as fine a grit (at least 220) as your
patience will allow. Another alternative
is to use flexible sheets of diamond
a brasives (backed with pressure-sensitive
adhesive) stuck to a piece of plate glass or
a flat steel bed. These abrasives are
available in three grits: 200, 400, and
800. Some tool catalogs sell special steel
lapping plates for use with silicon
carbide powder, but these are expensive
and too short for any but smaller planes.
I most often lap plane soles on a piece
of scrap plate glass with silicon-carbide
powder and kerosene as a lubricant. It is
a little messy, but the abrasive cuts
quickly. The glass eventually does wear
hollow, so I either flip it over or get a
new piece. I've heard that a thin sheet of
hard plastic on top of the glass works
even better because the abrasive particles
get embedded in the plastic and are held
in place.
Before you start la pping, back off the
iron and tighten the frog. Don't remove
the iron and the frog because they
create stress on the sole that could affect
its flatness if they are taken out. When
lapping the sole (particularly on small
planes) be especially careful to keep the
plane perfectly flat on the lapping table,
with the pressure about in the middle of
the plane. I take a few strokes in one
direction and then rotate the plane end
for end and lap the sale an equal amount
in the same direction. With care, you can
work side to side too, first one way and
then the other, making sure you keep
even contact on the lapping table and
don't rock the plane. After a dozen or so
strokes the sale will clearly show the high
areas as lighter metal or contrast against
When l appi ng
the sal e of a pl ane,
keep the pl ane
fl at on the l appi ng
tabl e and the
pressure even.
A lapped sal e
shows consistent
l appi ng marks
(the dul l surfaces) .
especi al l y at the
cri ti cal areas of the
toe, heel , and j ust
ahead of the throat.
Thi s sale needs
more l appi ng, but
it's getti ng cl ose.
the uniform milling marks on the sole of
new or little used planes.
Keep lapping until the sale is either a
consistent color, or at least the areas of
the toe, heel, and in front of the throat
are lapped level. Check the sale often
with a true straightedge. The rougher the
work you expect to do with the plane,
the less perfect the sale needs to be down
its entire length, especially for the longer
bench planes. Don't worry about small,
low spots in the sole. The sales of small
T U N I N G A P L A N E 55
planes need to be flat, but flattening
them should be easier considering their

size. Take extra time with your smoothing

planes and with planes meant to cut
with a lot of accuracy, such as shoulder
planes and rabbet planes.
If you intend to use a block, miter, or
jack plane with shooting boards, take the
time to square either or both sides of the
plane body to the sole. Shooting boards
are jigs for holding the work in various
ways so that edges or miters can be
squared or trued (see Chapter 7). Since
the plane is used on its side and the sole
is vertical, having the sole and sides
perfectly square to one another will
ensure more accurate cuts. Check the
sides and sole for squareness first with a
square, and then lap each side favoring
the position that will bring the side and
sole into square with each other.
Fl atten the sol e of a wooden pl ane agai nst a l ong j oi nter hel d upsi de-down in a vi se.
While not the most enjoyable work,
flattening the sole is rewarding-your
plane will work better and with more
accuracy. Moreover, once a tool is put
into shape it will stay that way a long
time, perhaps for many years. It is good
rainy day work that you can start and
come back to as the spirit moves you.
WOODEN SOLES
The soles of wooden planes are far less
tedious to condition, which is
convenient considering that they need
attention more often. The fact that wood
is softer than cast iron and more easily
worn out of true is only part of the
reason. Seasonal humidity changes affect
the sole, as does moving the plane to a
different climate (as when importing
English tools) or even leaving the plane
lying in the hot sun.
Take a good look at any old wooden
bench plane and chances are you'll see
what happens after years of reflattening
56 C H A P T E R F 0 U R
the sole. Since the greatest wear takes
place ahead of the throat and the throat
is well forward of the center of the sole,
years of reflattening the sole cuts the toe
faster than the sole and the body becomes
wedge-shaped. Every shaving taken off
the sole also widens the throat and the
plane cuts more poorly, to the end that at
some point the plane either needs a new
sole or a new throat piece (explained in
Two ways to repair
a worn wooden
sol e are to i nlay a
throat pi ece (as on
the j oi nter at left) or
t o gl ue on a whol e
new sol e (as on the
smoother at ri ght) .
the section on adjusting the throat on
pp. 61 -62), or must be kept for only the
roughest of work.
Check the sole first with winding
sticks and a true straightedge to see if
you are dealing with a twisted sole as
well as one worn out of flatness. Make
sure the iron is wedged into place just
shy of the throat opening, so that the
pressure it exerts on the sole will be the
same as when the plane is in use. If it is
not, it could later cause the sole to bulge
out just underneath the iron.
The truest way to flatten the sole is
to push the plane across a jointer plane
clamped upside-down in a bench vise (see
the top photo on the facing page). Keep
checking the sole with a straightedge and
winding sticks. Small adjustments can be
made with a very finely set block plane
or a scraper. You could also use a lapping
table and sandpaper. The sole can be
scraped ever so slightly hollow in the area
just forward of the heel and shy of the
throat, and the same amount between
the throat and toe. Chamfering the
edges where the sole and sides meet will
eliminate a sharp edge that could
splinter or mar the planed surface if the
plane should accidentally be tilted onto
its edge while planing. The chamfered
edges will also feel better in your hand.
Some wooden planes are worth
repairing with a whole new sole when
they are worn to the point that the
throat is too wide or when some other
defect needs correcting. I've even done
this to worn molding planes when I
wanted a new sole profile (see p. 194).
Repairing a sole is not difficult. To add a
new sole, plane the old sole flat, with the
blade wedged in place as for truing it,
and then glue on a new sole at least
:
1
6 in. thick-even thicker is better.
Dense, oily woods like rosewood, ebony,
or cocobolo work very well; just take care
to plane the mating surfaces before
gluing for the best bond. Yellow glue or
epoxy works fine. Make the new sole
oversized in every dimension and later
true it to the original body and carefully
drill and chop out a tight throat opening.
Fine-tune the throat with the iron
wedged in place. Finally, chamfer all
around the edges of the new sole.
Adjusting the Frog
of Metal Planes
Early on i n the development of the cast
iron bench plane a wide variety of
different frog designs were proposed and
patented. Some frogs were cast integrally
with the plane body, others were a
separate casting fitted to the plane later
(see the photo below). Today you are
likely to come across either of two
adjustable frog designs: a Bailey frog
common in Stanley, Record, and most
bench planes, and a Bed Rock frog found
in Stanley's line of Bed Rock planes (see
the sidebar on p. 47).
Both frog designs are separate castings
with a bed milled flat and another
milled area on the frog's underside
where it mates with the sole. The Bailey
frog screws directly to a thickened part
of the sole casting. On planes made after
1 914, the frog can be adjusted forward
and backward with a fine-threaded
screw, once the hold-down screws are
loosened. Moving the frog fine-tunes the
throat opening, but the iron must be
removed first to expose the screws.
The first patented cast-iron pl ane, Hazard Knowl es' pl ane of 1 827 (at rear), had a frog cast
i ntegral l y with the body. Another early cast-iron pl ane, a Birdsi l l Hol l y smoothi ng pl ane of 1 852
(foreground) , had a frog added t o the pl ane and connected with the tote f or better support.
T U N I N G A P L A N E 57
A Bai l ey frog is
adjusted by
looseni ng the two
hol d-down screws
that secure it to the
sol e casti ng.
A Bed Rock
frog has a l arge,
accurately mi l l ed
beari ng surface
and fi ts withi n a
groove that keeps it
perfectly al i gned.
I t' s secured wi th an
i ngeni ous system of
two pi ns ti ghtened
wi th screws from
behi nd the frog.
58 C H A P T E R F 0 U R
Good cutting performance comes
from a well-secured frog. I've had only
one problem with a Bailey frog over the
years, but it was serious enough to make
the plane useless. A previous owner had
overtightened one of the screws that
secure the frog to the sole and stripped
some of the threads. It's easy to see how
this could happen, considering the
softness of cast iron and the shortness of
the screws. My solution was to cut the
threads slightly deeper with a bottom
tap, just enough to grab hold of with a
slightly longer screw. If this didn't work,
I was going to try tapping the hole one
size larger and use a bigger hold-down
screw. I mention this problem for the
lesson it tells-don't overtighten the
screws that secure the frog.
The Bed Rock frog is an improvement
over the Bailey design in three ways: The
frog bears on the sole with a larger milled
flat and thus is more stable; it fits within
a groove, which keeps it perfectly aligned
with the throat; and it is held to the sole
with two pins that have conical dimples
in their sides. Two screws with tapered
ends set in the sole behind the frog
secure it; as the screws engage in the
dimples the pins are drawn downward
and tightly lock the frog. The beauty of
this system is the ability to adjust the
frog without having to remove the iron
and the frog's strong positive connection
to the sole.
Before adjusting anything, remove the
frog and lightly lap or flat-file the bed
(the surface the iron lies on) to take out
any burrs and check that it is reasonably
true and flat. (You can also file the bed
with the frog in place, as shown in the
photo at left on the facing page. ) The
depth-adjuster lever and the screw that
holds the lever cap are in the way;
remove the screw and work around the
lever. Check that the areas where the
frog and sole mate are clean and free of
burrs, too. Reassemble the frog in the
plane and barely tighten the screws that
secure it.
At this point, I like to run a small,
fine file into the throat and check that
the bed angle of the sole at the back of
the throat is the same as the frog bed
angle. Adjust the frog by sliding it or
screwing the adjusting screw: backwards
opens the throat, forwards closes it. By
sighting down the bed and looking at the
throat opening or the sole at the back of
the throat, you can see if the frog is
File the frog fl at,
after fi rst removing
the l ever-cap screw.
Work i nto the throat
to true the bed to a
consistent angl e
ri ght to the sol e.
Si ght i nto the throat al ong the frog, checki ng that the frog and the
bevel of the sol e are al i gned. Use a smal l strai ghtedge i f necessary.
slightly tilted out of alignment. Get it as
straight as you can (parallel with the
front of the throat)' Holding the flat side
of a small straightedge against the bed
and into the throat will help (see the
photo at right above), or you can put the
iron back in and look at the throat
opening. Where you should set the frog
depends on the work you expect to do
the section that follows will help you
decide. Carefully tighten the hold-down
screws when everything is aligned.
Adjusting the Throat
If you have only a few planes, you could
be changing the throat opening of ten-a
narrow throat for fine work, a wider
throat for rough work and coarse
shavings. If, like me, you have the luxury
of owning several planes, you can set
each plane with a different throat
opening and choose the best plane for
the work: a smoothing plane with a
narrow throat, a jointer with a medium
throat, and a jack with a coarse throat.
T U N I N G A P L A N E 59
F i ne - Tuni ng th e Thr oat and th e F r og
BAILEY PLANES
Frog
Sal e
Gap behi nd
iron
Frog
Sal e
Bevel the front of
the throat for easy
escape of shavings.
The frog and the bevel
of the sale should be
in alignment.
Setting the frog too far
back leaves the iron
unsupported, causing
chatter.
Setting the frog too far
forward leaves the back
of the iron unsupported,
again causing chatter.
60 C H A P T E R F 0 U R
BED ROCK PLANES
The frog extends right to
the sale, giving excellent
support to the iron and
minimizing chatter.
WOODEN PLANES
Bed (one
continuous
sl ope to sal e)
The throat of most
wooden planes is
already beveled to help
keep the throat tight as
the sale is resurfaced.
With an adjustable toe piece, common
on block planes and some other specialty
planes (see the sidebar on p. 1 1 3), you
can have an even wider range of choices.
CAST-IRON PLANES
Setting the throat width on a cast-iron
plane does involve some trial and error,
given the unique shape of each throat
and the way the shavings curl within it.
Before you adjust anything, make sure
the front of the throat opening is straight
and bevel it slightly to help the shavings
pass smoothly out of the throat. With
the Bailey-type frog, remove the iron and
either slide the frog forward or backward,
or move it with the adjusting screw.
Retighten the screws and reassemble the
iron and lever cap.
Bed Rock frogs adjust in the same
way, with the added ease of not having to
remove the iron. For fine smoothing
work a throat opening just shy of Y64 in.
is good, for general bench work between
Y
3
Z in. and YI6 in. , and for rough work
wider still. One rule of thumb that
makes sense is to set the throat a little
wider than the thickness of the shaving
you expect to cut. The narrower the
throat, the better it is able to support
the chip as it is broken and curled and
the smoother the finish in difficult
grain. Just don't try to take too thick a
shaving with a fine throat-the plane
will quickly clog.
There is one more subtle difference
between the two types of frogs that you
should keep in mind when adjusting
them. The front edge of the Bed Rock
frog mates with a part of the sole
thinned down to receive it, whereas the
Bailey frog has a noticeable thickness of
sole under its front edge (see the drawing
on the facing page). If either frog is
moved too far back the iron will bed
against the beveled part of the sole and
not the entire frog. Moving the frog well
forward eliminates any support that the
back of the iron gets from the beveled
edge of the sole. Either way the iron does
not get adequate support, causing it to
cut unevenly, or "chatter." The design of
the Bed Rock frog allows for a greater
range of throat adjustment without
causing a problem.
WOODEN PLANES
In keeping with their simplicity, wooden
planes do not have an adjustable frog,
but the throat can easily be tightened.
The throat opens over time due to
flattening of the sole, wear, and the slow
thinning of a tapered iron. (The back
ward slope of the throat helps slow the
rate of opening.) To close the throat,
pack out the bed behind the iron with a
thin sheet of copper, leather, or even
To i nl ay a throat
piece, posi ti on the
patch on the sol e
and scri be around it
with a kni fe. Chi sel
or rout out the
recess to a depth
sl i ghtl y less than
the thi ckness of
the patch.
dense cardboard-whatever it takes to
shim the iron enough to tune the throat.
If you use a thick shim, the wedge might
need some careful adjustment with a
block plane.
When the throat is really worn or
has grown too big, another alternative is
to glue on a new sole (see p. 57) or to
cut out part of the sole and fit in a throat
piece (see the photo on p. 56). The
same type of throat piece (only movable)
is sometimes found on well-made
European smoothing planes. The beauty
of a throat piece is that it is replaceable
and it can be made out of a dense wood
that will hold up to the extra wear on
this part of the sole.
To fit in a throat piece, start by
cutting out a patch to inlay into the sole,
T U N I N G A P L A N E 61
an angle roughly equal to the bed angle.
lcan imagine that it takes some care to
fit the key precisely, but otherwise the
method is beautifully simple and allows
for continued reflatten ing of the sole
without widening the throat. I was lucky
enough to find such a throat repair on an
English miter plane-a plane that greatly
benefits from a tight throat (see the
photo below). I also have a Chinese plane
with a variation on this theme; it has a
steel dovetailed key fitted just ahead of
the iron where it will hold up to
maximum wear and keep the throat
consistently fine.
The new throat piece on t hi s l i gnum-vitae smoother is secured i n
pl ace wi th gl ue and screws.
Sharpening
with the throat edge as wide as the
throat and gently tapered toward the toe.
A thickness between '+ in. and 3/8 in.
works well. Square the edges with a block
plane, and then lay the piece into
position just ahead of the iron. Make
sure to position the patch close enough
to the iron so that when recutting the
throat some of the patch will be cut
away. Mark around the throat piece with
a fine knife (see the photo on p. 61 ), and
then chop and chisel a recess to the lines
slightly shallow of the thickness of the
patch. It is not vital that the fit be perfect,
because the patch will be held in place
with glue (and with countersunk screws,
too, if you prefer)' Back up the thin
patch with a scrap block when gluing
and clamping it in place. When the glue
has set, plane the patch down to the level
of the sole, either by passing the plane
over an upside-down jointer clamped in
a vise or by using a smaller plane.
To cut the throat, remove the iron and
enlarge the opening with a fine sawblade
or chisel. Keep paring it and checking
with the iron in place. Err on the side of
too tight and try the plane to get the best
62 C H A P T E R F 0 U R
opening. You can always enlarge the
throat slightly later.
In his book Japanese Woodworking
Tools (The Taunton Press, 1984), Toshio
Odate describes a Japanese method of
closing up the throat with a sliding
dovetail key. The key drives through the
body of the plane toward the iron and at
If you ever want to get a heated
discussion going among woodworkers,
just mention the subject of sharpening.
Everyone has an opinion on waterstones
versus oilstones, hollow grinding, micro
bevels, and every aspect of sharpening
technique. To some it almost borders on
religion. So I'll jump into the fray with
my opinions.
An i ngeni ous way to ti ghten the throat on a wooden pl ane i s with a wedge-shaped key let
i nto the body, as on t hi s Engl i sh miter pl ane. Anyti me the sole i s j oi nted flat, dri vi ng the key in
ti ghtens the throat sl i ghtl y.
The sharpening debate really heated
up about 20 years ago when natural
Japanese waterstones with their unique
sharpening abilities came on the market.
Now with new, synthetic waterstones,
which are less expensive and very
consistent, more and more woodworkers
are trying waterstones and liking the
results. Affordable diamond and ceramic
stones have recently added more
sharpening possibilities, with long
wearing surfaces of many grits that cut
quickly and stay flat. Still in the debate is
the more conservative crowd who
learned how to sharpen with oilstones,
like the results, and see no reason to
change. I have to admit to falling some
where between all of these camps-I like
the rapid cutting of waterstones, I use
diamond stones for some sharpening,
but I'm most comfortable on my
oilstones. Really it all comes down to
habit: We tend to stay with the stones
and techniques we learn first.
There is even more to the sharpening
debate besides stones. Nearly every tool
catalog would love to sell you machines
and jigs to make your sharpening quicker
and more accurate. You can buy
motorized grinders, some of them water
cooled, and a whole variety of grinding
wheels. You can sharpen with narrow
belt sanders and buffing wheels. And
there are sharpening jigs that support
the iron at a consistent bevel and gauges
to check the bevel angle. However, with
good sharpening technique, you can
get excellent results with a minimum
of gadgets.
Sharpening is one of the most basic
woodworking techniques. It affects the
way a tool cuts, the ease and accuracy
with which it works, and how safely it is
used. Naturally a sharp tool cuts with
less resistance; it's the dull tool that takes
more effort and is more prone to
slipping, causing you injury or ruining
your work. But sharpening takes time to
master-no matter how long you have
been at it there is always more to learn.
Understanding the processes of grinding,
shaping the iron, honing, polishing, and
flattening the back is only part of the
story. The hardest part is training your
hands, arms, and eyes to work together
efficiently and accurately. Relying on jigs
A water-l ubri cated treadl e gr i ndstone was the
father to modern hi gh-speed and smal l er
stoned versi ons.
or gauges is one way to train your eye and
get consistent results, but I feel that
ultimately your body is the best jig and
good results come from relying on
coordination and observation.
GRINDING THE BEVEL
The first step in sharpening any iron is
grinding a consistent bevel angle. The
fastest method is to use a motor-driven
grinding wheel-a useful tool in any
shop-though the bevel can also be cut
on coarse stones. My grinder is a simple
shopmade affair made from an old
washing-machine motor driving a pair
of wheels mounted on an arbor (see the
photo below). The wheels are 6-in.-dia.
60-grit and 1 20-grit aluminum oxide.
It isn't a fancy grinder, but it does every
thing I need. A step up would be a
II-hp Baldor grinder with a pair of 8-in.
The fastest and
most accurate way
to establ i sh the
bevel angl e i s to use
a motor-dri ven
gri nder. I n thi s no
fri l l s setup, the i ron
rests i n a si mpl e j i g
that is movable
backward or forward
to gri nd different
bevel angl es.
T U N I N G A P L A N E 63
B E N C H S T O N E S
Y
OU can spend a lot of
money in a hurry on
sharpening stones, but how do
you choose the ones best
suited to your skills and
needs? How are oilstones
different from waterstones?
What about synthetic water
stones, or for that matter all
man-made stones compared
to natural ones? To under
stand some of the immediate
differences between
sharpening stones, the best
place to start is to look at their
physical qualities.
Physical qualities
Of all the many hundreds of
naturally occurring stones,
only a handful combine the
five qualities that make them
really useful for sharpening:
the size of the particles, their
shape, hardness, and tough
ness, and the strength of the
bond that unites them. A
Japanese master craftsman
would add the more subtle
qualities of color and pattern
to this list.
Particle size: Most
desirable for consistent
sharpening abrasion is a stone
of uniform grit that's free of
larger particles (anomalies).
Natural waterstones have an
amazingly consistent particle
size, graded by the ancient
rivers that deposited them.
Shape: Sharp, angular
particles, natural or man-
64 C H A P T E R F 0 U R
Natural waterstones are quarri ed sedi mentary rock, each with sl i ght di fferences in hardness, grit si ze, and
col or. Despite thei r subtl e fl aws, natural stones are rare and can sel l for many thousands of dol l ars.
made, cut faster than ones
that are more rounded.
Hardness: Particles need to
be hard to abrade tough steel
and hold up to wear.
Toughness: Particles must
be tough enough to withstand
the pressure and forces
generated during sharpening.
Yet some particle breakdown
is desirable on finer stones to
polish the cutting surfaces.
Bond: The (glue" that holds
the particles together is one of
the most important qualities
of a stone. If the bond is too
strong, it doesn't allow the
particles to wear away and
expose a fresh surface; if the
bond is too weak, the stone
wears hollow more quickly.
Waterstones have a weak
bond; oilstones and ceramic
stones a strong bond.
No stone is going to be
perfect for all of your sharpen
ing needs. A coarse stone used
to hone out a nick or roughly
refine a bevel will have very
different characteristics from
a finishing stone used to
polish the edge. At the very
least, you'll need a few stones
of different grits: a coarse
stone, a medium stone, and a
finishing stone. Whether you
use oilstones, waterstones, or equal to natural stones at a
newer diamond and ceramic much lower cost. Some
stones is a matter of personal synthetic stones are made by
choice and budget. Try out as grinding up natural stones,
many as you can, because once mixing in some sort of binder
you settle on a system there is (clay for one), and firing it.
a good chance you will stick Others are made by fusing
with it for a long time. manufactured abrasives
together. The resulting bond
Waterstones between the particles is
At one time, all waterstones
intentionally weak, so the
were natural stones. Stones
cutting surface is constantly
were known and named
being renewed and the stone
depending upon the strata
cuts easily and rapidly. The
they were quarried from, each
drawback (for natural stones,
with slightly different
too) is a relatively soft stone
characteristics and sharpening
that wears rapidly and
abilities. Master blacksmiths,
requires more frequent
in a tradition that mixes
maintenance. Fortunately, this
science and spirituality, even
is not a difficult chore (see the
went so far as to specify which
sidebar on p. 70). A useful set
stones should be used to
of stones is 800x, 1 200x, and
sharpen their particular tools.
6000x. To see if you like water-
Natural stones are still being
stones, I suggest buying a
quarried in Japan, but the
couple of inexpensive
better ones have become very
combination stones with a
expensive-sometimes costing
different grit on each face.
many thousands of dollars
A lubricant is necessary
each. Are they worth it,
for any stone to wash away
compared to a good man-made
the worn abrasive and metal
waterstone? Although the
particles (called "swarf").
ones I've used gave no better
Using water as a lubricant
edge to my tools, they
with waterstones has its
certainly had a wonderful
advantages and disadvantages.
silky feel. Some believe that
Waterstones need to be soaked
the cutting action of natural
in water before they can be
stones sharpens Japanese tools
used, which can take a few
better than any others.
minutes. If you store your
Today, the better man-
stones in water, another
made waterstones are of a
option, you run the risk of
quality and consistency nearly
freezing (and ruining) them in
a cold shop. While I like their
fast cutting, waterstones are
messy. I've never been totally
comfortable with all that water
around my polished tools.
Oilstones
The main difference between
oilstones and waterstones is
the particle bond. Oilstones
are more tightly bonded and
stay flat longer, but they're
also more likely to glaze over
and cut slowly. Using a light
honing oil or kerosene as a
lubricant helps flush the
surface, but the stones still
need routine maintenance to
cut like new. I use a fine India
and hard black Arkansas more
than any other stones, for
honing a fine edge and the
back of the iron truly flat.
Oilstones come in a range of
grits both natural and man-
made-a good set would
include a coarse, medium, and
finishing stone.
Diamond and
ceramic stones
It's only in the last decade or
so that diamond stones have
shown up in woodworking
catalogs and caught on as an
alternative to waterstones or
oilstones. The beauty of
diamond stones is that they
work equally well for carbide
tools as for steel ones. To
resurface and flatten oil- or
waterstones they are
unequaled. The best diamond
stones are monocrystalline
diamonds bonded to a flat
base. They come in a range of
grits, but none that are truly
finishing stones for final
polishing. They can be used
dry or with water or kerosene.
You would think that as hard
as diamonds are that these
stones should last forever, but
in fact the diamonds can be
worn down quite easily with
too much honing pressure and
aggressive use.
The newest sharpening
stones are ceramic stones.
They are similar to man-made
waterstones, except that they
can be used dry and need no
soaking. They are extremely
hard wearing, they stay flat,
and they can be cleaned
under running water. So far,
they come in a small range of
grits useful only for finishing
an edge.
Ultimately it is more
important how you use and
maintain your stones than
which ones you choose. While
sharpening, keep the surface
well flushed with lubricant
and use only modest pressure.
Regularly check your stones
for flatness and maintain
them. Have a range of grits, no
matter if some are oilstones
and others something else,
and learn to use them all to
get the keenest edge in the
shortest time.
T U N 1 N G A P L A N E 65
wheels. One thing you do need is a jig for
holding the iron at a consistent angle to
the grinding wheel. The jig can be
shopmade, or you could spend quite a bit
for one with all the bells and whistles.
More important than how you get
there is that you achieve a proper bevel
angle. If you read Chapter 3 on bevel
angles, you'll realize that there is no
"right" bevel angle. Any bevel angle is a
compromise between the durability of
the edge, the work required of the plane,
the bed angle, whether the bevel is up or
down in the plane, and whether a back
bevel is used. You can get hopelessly
caught up in the science to try to arrive
at the best bevel, but within a modest
range of bevels most planes will work
just fine. You can fine-tune each plane
by experimenting with the bevel angle
every time you grind or hone.
For bench planes and bevel-down
irons, a bevel angle of 25 is a good place
to start. A good rule of thumb is to
make the length of the bevel twice the
thickness of the iron. Honing a 5 to 10
microbevel for an overall edge bevel of
30 to 35 gives the edge adequate
durability. For bevel-up planes (block
planes, low-angle planes, and some
spokeshaves), 20 to 25 is a safe bevel
angle. The more acute the bevel angle the
lower the cutting angle, which is what
you want in these planes. With modern
alloy irons, this angle could be reduced
5 or more. You could also save one plane
for working soft or easily worked woods
and bevel its iron even lower still.
Hollow grinding
The bevel cut by a small-diameter
grindstone is ground hollow, whereas the
bevel shaped with a stone is not (see the
drawing above). Whether to hollow
grind is part of the ongoing sharpening
66 C H A P T E R F 0 U R
G r i nd i ng a H ol l ow B eve l
Pl ane i ron
" . ' . - ,
Gri ndi ng wheel
Hol l ow bevel ,
Straight bevel
Hol l ow/straight bevel ..
, , \
'
debate. The advantage of hollow
grinding is the speed with which the
actual cutting bevel can be honed,
without having to remove metal across
the entire bevel. Every time you
resharpen, the hollow is slowly honed
away or grows so small that eventually
the bevel needs to be reground.
Woodworkers who don't hollow-grind
believe that the cutting edge is stronger
since it is fully supported by a bevel the
whole thickness of the iron. This is
certainly true if the hollow extends very
close to the cutting edge. In practice,
hollow grinding with an 8-in.-diameter
or larger grinding wheel and honing the
bevel 64 in. or more creates an edge
that's adequately strong. For Japanese or
A hOllow-ground edge tends to
be weak, but it is easy to hone.
A straight bevel has a strong edge,
but the entire bevel needs to be
honed when sharpening.
The best compromise: a strong
edge and a hollow grind for easier
honing.
other hard irons, a slight hollow grind
and then honing the bevel well back
from the cutting edge will give the iron
the necessary durability.
I always hollow-grind my plane irons,
but I make sure to leave a thin line of
polished steel where the bevel was last
honed. In this way, I maintain the shape
of the iron and use the grinder only to
remove enough steel to make the honing
process easier and quicker.
Shaping the iron
There's an old saying that a plane iron
writes its name on the wood. Its
signature depends a lot on how you
shape the length of the cutting edge:
I r on Pr of i l es
Straight i ron for j oi nti ng o r for
rabbet and dado planes
________-
0. 001 i n. )
Gently rounded iron for
pl ani ng sl i ght texture i nto
surface; best for smooth or
jack pl anes
____ -A ____ -
Check shape against
block of wood.
Strongl y profiled for scrub
pl anes or for rapid stock
removal with any pl ane
Sl i ghtl y rounded corners
for smoot hi ng planes or for
fi ni sh work with any pl ane
straight across, with a slight convex
profile, with a pronounced convex
profile, or with just the corners rounded
off (see the drawing at left). Why even
shape the iron at all you might ask?
The usual reasons are for aesthetics
(the planing marks make a nice pattern)
and for improved performance. A
pronounced convex profile is common
on scrub planes or jack planes used to
remove a lot of wood quickly. The iron
cuts like a wide gouge. A slightly convex
iron works well in a smoothing plane
since only part of the iron is cutting and
the strokes will blend together nicely
with the outer edges of the iron out of
contact with the wood. A convex iron
will chatter less because there is less
pressure upon it. Most of the time I
shape the iron by only slightly rounding
the corners, because this profile gives
me the benefits of a shaped iron but
with a maximum amount of the iron
cutting. Since more of the iron is cutting,
I resharpen less often than I would with
a more convex shape.
To shape a convex edge, I grind more
heavily on the outer edges of the iron,
gently pivoting it over the grinder in a
slight arc. This is where my simple
grinding jig works particularly well, by
keeping the iron oriented at a consistent
bevel to the stone while I arc it. After
grinding I hone a consistent shape.
Occasionally, I check the shape by
holding the iron against a straight block
of wood held up to the light. Only the
slightest curvature is necessary and it
need not be a perfect arc. While using
the iron, I can judge how I need to refine
the shape next time I resharpen, either
to give it a little more shape or to hone
some out of it.
FLATTENING THE BACK
OF THE IRON
Given that it forms half the cutting
edge, a flat back on the iron is every bit
as important as a well-honed bevel.
Unless you are regularly going to use
back bevels, the back of the iron must be
polished and flat; otherwise, the iron
will never be truly sharp. Of all the
many plane irons I've sharpened over the
years, I can remember only four that
came to me with backs properly flat.
Three were for new Lie-Nielsen planes,
obviously carefully finished with
modern technology, and the other was
for a plane bought from another
craftsman who had used it a great deal.
Every other iron has needed from a half
hour to many hours of lapping to get the
back flat and polished.
There is no question that this work
can be tedious. Of course, you could
send your irons to a machine shop and
get the backs surface-ground, but they
would still need some hand lapping.
Think of it in the same way as flattening
the sole of the plane; the results are well
worth the effort and, once done,
maintaining the iron is fairly simple.
I lap the back flat on the same
sharpening stones I use to hone the bevel
(see the top photo on p. 68). A large
diamond stone or a special lapping steel
sprinkled with silicon-carbide powder
also works well. More important than
what you use is that the lapping surface
be perfectly flat, or you will polish the
back but it will not be flat. This is where
I love my slow-wearing oilstones, which
tend to stay very flat with little routine
maintenance. The only way to find out
how flat the iron is, is to start lapping. If
it is really bad or slightly rust-pitted, I
start on a coarse waterstone that has
been recently trued. The area all behind
T U N I N G A P L A N E 67
Lappi ng the back of the i ron is every bi t as i mportant as honi ng the bevel. Lap unti l the back i s
consi stentl y pol i shed ( l i ke the i ron to the ri ght) and fi ni sh on a fi ne stone (such as the Arkansas
stone i n the background) .
Gri ndi ng the back of the i r on wi th a dr i l l and a smal l gri ndstone speeds up the process of
honi ng t he back. I t ' s an i dea si mi l ar t o hol low-gri ndi ng t he back of a Japanese pl ane i ron
(shown at l eft).
68 C H A P T E R F 0 U R
the cutting edge should finish to a
consistent polish.
There is one trick that helps speed
along the flattening process. Looking at
the hollowed backs of Japanese chisels
and plane irons, I got the idea that I
could do the same thing with a power
drill and a small grindstone. These
inexpensive stones come mounted on
an arbor and are sold in many hardware
stores. I use a 3/s-in. by 1 Yz-in. stone
chucked in a drill (see the bottom photo
at left). Lap the iron on an oilstone a
little first, and then grind the polished
spots (the high areas), staying away from
the cutting edge. I don't touch the dull
areas because they're not contacting the
oilstone yet. By grinding and honing I
eventually get a back polished and flat.
Often there are small grinding marks
left, but these will be gradually honed
out every time I resharpen.
HONING
Honing is all of the work done on bench
stones to refine the bevel and bring the
tool close to final sharpness. Whether
you use waterstones, oilstones, diamond
stones, or ceramic stones, the honing
process is the same. Of all the sharpening
techniques, honing probably causes the
most difficulty for the inexperienced. It
takes time to learn the process, and even
longer to develop a feel for the subtleties.
I have five stones that I use regularly.
Two are inexpensve waterstones that
have a coarse grit on one side and a fine
grit on the other (see the top photo on
the facing page). I use them for quickly
shaping an edge or for roughly flattening
the back of an iron. The stone I use
most often is a fine India oilstone with
kerosene as a lubricant. This is a man
made stone that cuts at a moderate speed
and wears slowly enough to stay true.
Nearly everything pas;es over this stone
during the sharpening process. For a
final polishing of the edge I use either a
hard black Arkansas (oilstone) or an
awase toishi (a natural waterstone). For
more about differences between stone
types, see pp. 64-65.
Nearly all experienced sharpeners
have a distinct style. It may be the way
they hold the iron, the speed of the
strokes, or the pattern they make across
the stone. The end results are no
different. Only two things are important
to bear in mind: Keep the iron at a
consistent angle to the stone, and use as
much of the stone as possible so as to
wear it evenly. My technique is to
lubricate the stone and then rock the
bevel upon it to feel the angle that is
closest to the ground bevel angle or the
old honing angle. One advantage of
hollow grinding is that it is easier to feel
the bevel angle because the bevel rests on
the cutting edge and the back of the
hollow grind. To hone a microbevet raise
the angle of the iron a few degrees.
When I feel the bevel is right I lock
my hands and, moving from my arms,
stroke up and down the stone in narrow
figure eights (see the bottom photo at
right). Light pressure is all that is needed
(and it will keep your stones flat longer).
Skewing the iron at about 20 feels
more comfortable to me than honing
straight up and down, except that the
leading edge gets cut faster and the iron
will hone out of square over time. I
compensate for this by increasing the
pressure on the trailing edge slightly.
After a dozen or so "eights" back and
forth, I take the iron off the stone, wipe
the edge, and look at it and feel it. If
there is a slight wire edge on the back, I
have cut a new edge. If not, I hone the
bevel further until I do. The next step
is to hone the back on the same stone.
It's really important to keep the iron flat
on the stone; one hand exerts pressure
on the iron against the stone, while the
Effective sharpeni ng demands usi ng a variety of stones, such as ( cl ockwi se from top) a hard
bl ack Arkansas fi ni shi ng stone, a medi um and fi ne I ndi a, and two-si ded water stones. A box
keeps each stone protected and hol ds the stone in place whi l e sharpeni ng.
Usi ng l i ght pressure
and with your arms
l ocked to mai ntai n
a consistent bevel
angl e, stroke the
iron up and down
the stone in narrow
fi gure ei ghts. Use
the enti re surface of
the stone.
T U N I N G A P L A N E 69
S T O N E M A I N T E N A N C E
S
ooner or lateyour bench
stones are gOIng to wear
unevenly or glaze over. Ten
minutes of maintenance will
restore the surface as flat and
sharp as when the stone was
new. My oilstones need
attention at most a half-dozen
times a year; my waterstones
about twice as often.
All stones can be renewed
with the same basic procedure
-the worn stone needs to be
lapped against a true and
abrasive surface with plenty of
lubricant. A cement block, a
coarse waterstone, a diamond
stone, or even a sidewalk
works well for waterstones.
I lap my oilstones on either a
diamond stone or at the same
plate-glass lapping table I set
up for truing plane soles (and
at the same time, too).
Ceramic stones can be lapped
on a diamond stone.
Lap the stone back and
forth with modest pressure
and check it with a straight
edge occasionally. It's just like
sharpening, the longer you
wait to tune up your stones,
the more effort it takes.
One way to renew the cutti ng surface and flatten oi l stones is to l ap
them on pl ate gl ass wi th si l i con-carbi de powder and kerosene, just as
for l appi ng a pl ane' s sol e.
other hand supports the free end (as
shown in the top photo on p. 68). Honing
the back up and down the stone works
the wire edge back onto the bevel.
Working alternately on the front and
back with decreasing pressure eventually
removes the wire edge and leaves a sharp
cutting edge. You know that you're done
when you hold the iron in a bright light
and don't see any reflected light from the
edge. A dull or wire edge will show as a
thin shiny line.
70 C H A P T E R F 0 U R
POLISHING
Polishing is a final honing on a very fine
stone that refines the edge to a mirror
finish. For polishing I use either a hard
black Arkansas or awase toishi, working
first the bevel and then the back in the
same manner as honing. A dozen strokes
on each surface is usually all it takes. The
feel of both of these stones is so smooth
that it hardly seems as though they are
cutting, yet the result is noticeable. Not
only is the edge sharper, but it will stay
sharper longer.
Another way to polish the edge is to
use a leather strop. An image of a barber
stropping the edge of a straight razor
probably comes to mind. For plane
irons you need a more rigid strop, made
by gluing a piece of smooth leather (as
opposed to a rough split face) to a wooden
block. The length and width of a large
bench stone is a good size. Rubbing a
fine abrasive compound into the leather
gives it the ability to polish. Polishing
compounds are available in a range of
grits; I recommend a fine grit such as
jeweler's rouge or tripoli.
The strop is used in a similar way to
honing on a benchstone, with the
important difference that the strokes
should all come toward you. Stropping
away from you will only dig the edge into
the leather. Strop the bevel a few times
and then the back of the iron, again
working toward you with every stroke.
Just as with a fine benchstone, if the
edge is not overly dulled you can bring it
back to sharpness on the strop alone.
For a more complete discussion of
sharpening technique and sharpening
stones, refer to Leonard Lee's The
Complete Guide t Sharpening (The
Taunton Press, 1 995).
Final Tuning
If you have followed the tuning
procedure to this point, you should have
a sharp, correctly beveled iron with a
polished back, a sole that is flat, handles
that are tight, and a throat that is
adjusted for the work you expect to do.
The plane would probably work fine as
is, far better than before you started
tuning, but there are a couple of final
things worth checking. What you haven't
tuned are the cap iron, the lever cap (or
wooden wedge) that secures the iron,
and the depth adjuster.
CAP IRONS
The cap iron performs at least two impor
tant functions right at the heart of the
cutting action of the plane. It su pports
and adds rigidity to the cutting iron,
which is especially important with a thin
iron. The cap iron also presents a steeper
"wedge" than the cutting iron and helps
break and curl the shavings in the throat,
thereby improving the plane's ability to
handle difficult woods. In order to do
either of these jobs, the cap iron must fit
the iron exactly so that no chips can
wedge between them. It must also be
properly set so that it supports the
cutting edge and helps curl the shavings.
When tuning the cap iron, think of
it in the same way as the cutting iron.
The leading edge needs to be sharp and
straight, and the top of the cap iron
should be polished in order to curl
shavings smoothly with little friction.
Fit the cap iron to the iron by first holding
them together with light pressure the
way they would mate in use. Looking
between them toward the cutting edge
you should see no light, but chances
are you will. Where there is light, a
shaving could wedge and clog the throat.
Besides that, the cap iron cannot fully
support the iron unless the two mate
along the entire edge. The back of the
iron should be flat, so it is the cap iron
that needs truing.
To true the cap iron, hone the mating
edge on a medium benchstone while
keeping the upper end of the cap iron
slightly lower than the stone, as shown in
the photo above. Working this way trues
the leading edge and hones a slight
Hone the undersi de
of the l eadi ng edge
of a cap iron on a
medi um-gri t stone,
keepi ng the other
end of the iron
sl i ghtl y l ower than
the surface of the
stone.
underbevel. Polish the top of the cap iron
with very fine sandpaper or steel wool,
and then wipe on a coat of paste wax to
help it work better and prevent rusting.
When you screw the cap iron and iron
together you should feel some pressure.
Sometimes you'll find that the bent part
of the cap iron has lost some of its spring
and it mates with the iron with little or
no pressure. In this case, the cap iron
simply needs a little more curvature.
I clamp the cap iron vertically in a vise,
with the point where the curve starts
right at the top of the jaws, and then hit
it a few times with a mallet (see the top
photo on p. 72). The steel is soft enough
to deform and hold the new shape, but
go easy. Check the way the iron and cap
iron mate and possibly rehone the
underside of the cap iron if necessary.
The final adjustment is setting the
cap iron to the iron (see the bottom
photo on p. 72). Ideally, the cap iron
should be as far from the cutting edge
as the thickness of the shavings you
expect to make. I set the cap iron and
cutting iron close to this position, just
T U N I N G A P L A N E 71
To put a l i ttl e more
spri ng into the
cap i ron, tap it ri ght
at the poi nt of
curvature whi l e it i s
hel d i n a vi se. Onl y
a sl i ght amount of
tensi on between
the i ron and the cap
is needed.
Adjust the cap i ron
just back from the
cutti ng edge for a
smoot hi ng pl ane
and fi ne shavi ngs
( l eft) or farther
back for coarse
work as in a scrub
pl ane ( ri ght) .
snug up the screw between them, and
then nudge the cap into final position
before tightening the screw fully.
LEVER CAPS
The standard Bailey or Stanley lever cap
usually needs little tuning, other than
keeping it polished, waxed, and set with
the proper tension against the double
72 C H A P T E R F O U R
iron. Polish it with fne sandpaper or
steel wool. As for tension, the lever cap
should release easily and lock down with
only modest pressure. Increase the
tension by turning the screw into the
bed that the lever cap locks over, or
decrease it by turning the screw out. If
the iron adjusts easily and stays set, the
pressure is right.
Block planes and other planes with a
single iron need their lever caps (or screw
caps in some cases) tuned further. In
these planes the lever cap does some of
the work of the cap iron, mostly
stabilizing the iron and assisting in
curling shavings. The end of the lever cap
should lie flat on the iron close to the
bevel. These lever caps are cast and then
chromed or painted, with little
machining done to them where they
mate with the iron. Flatten the
underside on a coarse stone as described
previously for a cap iron and shown in
the top photo on the facing page. Adjust
the tension against the iron in the same
way as for a bench-plane lever cap.
DEPTH ADJ USTERS
Depth adjusters usually need little
tuning, but a problem you may
occasionally encounter is backlash, or
play in the depth adjustment. As a result
of wear and generous manufacturing
tolerances, the Y"adjustment lever
doesn't always fit the brass adjuster
wheel tightly. On older planes with a cast
Y there is little you can do about it other
than keep the adjuster wheel set with
slight downward pressure on the iron.
By this I mean if I back the iron out for a
lighter cut, I then turn the adjuster the
opposite way (as if to lower the iron) the
quarter turn or whatever it takes to take
the backlash out. This ensures that the
iron will stay set.
On newer and inexpensive bench
planes the Y is soft steel and appears to
be made of two parts. Screw off the
adjuster wheel and slightly bend one arm
of the Y forward or backward. Trial-fit it
in the slot of the adjuster wheel to see if
it is a snug fit. For block planes, use a
vise or pliers to pinch the adjuster lever
where it captures the brass adjuster
wheel, as shown in the bottom photo on
the facing page.
WOODEN PLANES
If you've tuned your wooden plane with
the same techniques explained for a
metal plane, there's little else you need to
do. Part of the beauty of wooden planes
is their simplicity. Nevertheless, I would
check two final areas to eliminate any
possibility of their giving you trouble:
the bed and the wedge.
Just as with a metal plane, the bed for
the iron must be flat. One way to check
the bed is to put the iron in position and
see if it sits flat without rocking. If it
doesn't, looking at the bed surface might
give some clue as to high spots, which
will be worn to a slight polish or show
dark scrapes where the iron has rubbed
against the bed. Pare the high spots care
fully with a chisel, trying not to change
the bed angle, or better yet use a fine file.
Replace the iron to check your progress.
The iron need not touch over its entire
surface, but it should be fully supported.
The wedge might also need some
tuning. If the plane is well used, the
wedge has probably fitted itself to the
grooves in the plane's cheeks that secure
it. Ideally, with a light setting tap, the
wedge should seat in the grooves along
their entire length. Most important is
that the wedge is tight against the iron
(or against the cap iron in the case of
double irons) close to the bottom of the
throat. Tuning the wedge involves careful
cuts with a block plane or file, trial
fitting it as you go. Tune the thin end the
same way you would the cap on a block
plane and give it a light coating of wax.
If you have taken your plane through
all the tuning steps described here, you
are going to be well rewarded. By under
standing how the parts work together,
you'll be able to fine-tune the plane for
the work you want to do or troubleshoot
any problems. And beyond sharpening
the iron, your plane will need little
maintenance to work to its best potential.
To take out any backl ash or sl op in the depth adjuster on a bl ock
pl ane, pi nch the adjuster lever wi th a vi se or pl i ers unti l it j ust fi ts the
adjuster wheel .
Tune a bl ock-pl ane
l ever cap by flatten
i ng the undersi de of
the l eadi ng edge on
a coarse stone. The
top edge shoul d be
pol i shed smooth.
T U N I N G A P L A N E 73
HOW TO PLANE
A craftsman is one who understands his tools and his material and uses
them with skill and honest. does not matter whether his tool is a chisel or
a planing machine, it is the work that he does with it that counts.
-Thomas Hibben, The Carenter's Tool Chest, 1933
Er a plane to cut well, it takes more
than using the right tool for the job and
tuning it correctly. The way you adjust
the plane, how you hold it, how you
stand and balance your body through the
stroke, and how you control and pressure
the plane are all part of successful
planing technique. Learning how to
clamp or hold the work effectively and
read the grain are just as important and
can make all the difference between
frustration and satisfaction.
The characteristics of a good bench,
various clamping strategies, and ways to
adjust the plane ready for work can be
explained. How to hold the plane, how
to stand when planing, how to vary the
pressure upon the plane through each
planing stroke, and how to read the grain
of a board can also be taught to a point.
But to plane well ultimately takes an
awareness of the tool that cannot be
taught-it must be felt. Fortunately,
there is much pleasure in the learning,
especially if you have a sturdy bench to
get started on.
A good, sturdy workbench is essenti al for hol di ng the work whi l e
pl ani ng. The bench on the faci ng page has a l arge si de vi se with
doubl e wooden screws and a sl i di ng board jack with peg hol es for
hol di ng the ends of long boards.
Holding the Work
It's hard to imagine doing good work
without a sturdy bench, but it doesn't
need to be elaborate to work well. Some
days my bench serves as a desk and
drawing table. Often it is a place to lay
out parts, to mark joints, and to hold the
work while cutting the joints. When I'm
gluing up, its flat top is perfect for fitting
parts and clamping against. It's where I
hone and polish chisels and plane irons
and occasionally file a saw. And every
working day my bench becomes a jig to
hold anything from rough planks to an
assembled tabletop to small drawers as
I work upon them with planes.
If a bench is a holding jig, the vises,
dogs, holdfasts, and stops are what give it
versatility. The beauty of these devices is
75
Late-1 9th-century
catalogs, such
as thi s one from
Chas. A. Strel i nger
of Detroi t, offered

Il'


I

1:\

a wi de vari ety of
workbenches to
sui t the needs of
speci fi c trades and
pocketbooks.


IUlat\UI.

t
nU'I'I" 1.... TIl',' III' put
' <tht-1 j,III

'

that they can work together or separately

to hold pieces of various shapes or sizes.
I rely mainly on the side and end vises,
because they adjust quickly, hold
positively, and give me a lot of clamping
options. It's the large or oddly shaped
piece that calls for more creative
clamping, but with a sturdy bench and
knowledge of the holding devices
available, anything is possible.
BENCHES
Benches come in many shapes, sizes,
types, and heights. They are as personal
as each craftsman, from the bench
maker designing and building the bench
to the bench-user fine-tuning each
aspect to suit his way of working.
Variations in bench design are most
often the result of the different work
performed upon them and the specific
traditions they evolved from. Joiners and
76 C H A P T E R F I V E
carpenters building parts of houses
needed flat surfaces and ways to clamp
wide and long parts. Cabinetmakers
needed a smaller bench and vises that
could hold irregularly shaped work.
Similarly, other trades adapted bench
designs to suit their needs.
Bench designs have changed very
slowly. A Roman workbench of well over
2,000 years ago wouldn't look a bit out
of place in a modern shop. It resembles
the basic bench found in many
production shops, built of a wide single
plank (more likely laminated solid wood
or plywood today), through-mortised
legs, and without any vise or clamping
device except for possibly a bench stop to
stop the work against. With the later
addition of an L-shaped, forged iron
holdfast (see p. 82), long boards could be
held along the bench top for edge
jointing. Eventually side or end vises
ill
II

were added to hold the work better, and
workbenches were built longer and
heavier and sometimes with drawers or a
shelf under the top as well. By the late
17th or early 1 8th century, workbenches
were little different from those typically
found in shops today.
Bench height
When woodworking was done entirely
by hand, workbenches were lower than
most are today. Planing on a low bench
puts more power into the stroke,
through the natural gravity of more of
the body driving the plane. Whereas
today's benches typically range in height
from about 34 in. to 38 in. or more, a
bench of a few centuries ago would have
been less than 30 in. high. Today's higher
bench is understandable considering
how much less physically demanding the
work is and that a bench is just as often
used for routing or cutting joints with a
chisel, where strength is less important
than getting the work higher and closer
to your eyes for better control.
There is no perfect bench height;
any height is going to be a compromise
between the many ways the bench will
be used. How tall you are and the kinds
of work you are likely to do can help
establish an optimum height. Like many
craftsmen, I have a bench that is modeled
on the bench that I learned on: an Ulmia
bench with a single side vise, an end
vise, and a row of dog holes along the
length. I copied the height too-34 '.in.
Considering that I am just under 6 ft.
tall and planing and other varied bench
work feels comfortable, this height is
ideal. If you're setting about building a
bench and are unsure of the best height,
you might want to build it an inch or
two lower, especially if you are shorter
than I am and expect to plane a lot by
hand. It would then be a simple matter
of fine-tuning the height with a board or
2-in. plank under each leg (or between
the top and base), which could be
secured with screws when you reach a
height that feels right. In the same way,
the height of a commercial bench can be
fine-tuned to your height and needs.
No bench is a perfect height for all
work. Sometimes I need to surface or
plane an edge on a piece of furniture
clamped 2 ft. or more above the bench
surface. Rather than lay the work on the
bench and work less efficiently and
accurately with a plane on its side (if I
even can), I prefer to clamp the work
upright. Even though it is awkward to
work at this height and use the plane
with any force, I can take a light cut with
a pass or two. When I need to plane
extensively at this height, I pull out a
h in. or 20 in. sawhorse to stand upon.
A higher sawhorse works too, and at
times I even stand on the bench itself.
,. us .
The si mpl est bench is part sawhorse, part fl at benchtop. Addi ng a
bench stop and an L-shaped hol dfast greatl y i ncreases its versati l ity.
( From Di derot' s Encyclopedie. )

H O W T O P L A N E 77
Benches don' t have to be el aborate to work wel l . Thi s basi c bench has everythi ng you need
to hold the work: a l arge, qui ck-acti ng si de vise, a flat top surface, and an adjustabl e stop
projecti ng through the top to pl ane agai nst,
A si de vi se wi th two
large wooden
screws is i deal for
cl ampi ng wi de
boards upri ght for
pl ani ng end grai n,
78 C H A P T E R F [ V E
SIDE VISES
If your bench has only one vise, chances
are that it is a side vise of some kind. A
side vise is the least expensive vise option
and the one most easily built or bolted
on. Side vises are usually mounted at the
left-hand corner of the bench, parallel
with the front edge and with the jaw(s)
flush with the bench top. In its simplest
form this vise is nothing more than a
wooden jaw with the clamping action
coming from a large wood or steel screw.
A small side vise opens about 8 in.; larger
ones 1 2 in. or more. It's a useful vise for
clamping work of modest size, short
boards, or irregular curved shapes.
There are many variations of the side
vise that add versatility or more clamping
strength. The leg vise is one such design
that originated in the 1 8th century. The
movable jaw usually extends right to the
floor to give the vise more stability, and
sometimes reaches 6 in, or so above the
benchtop. The result is a rugged vise
useful for chair makers clamping curved
parts while shaping them or for wheel
wrights fitting the spokes to a partially
completed wheel.
Another side-vise variation has
double screws through the jaw, which
not only allows great clamping pressure,
but also the ability to clamp work
between the screws (see the bottom
photo at left). This vise is as handy for
clamping a board upright to plane the
end grain as it is for clamping a tapered
leg. The double screws also overcome a
problem of the single-screw vise: It's easy
to strain a single screw by clamping too
heavily and racking the jaw.
Modern steel side vises such as the
popular Record ED series (shown in the
top photo at left) have design features
that combine some of these ideas. To
overcome the jaw-racking problem of a
single screw, steel side vises have two
steel rods parallel with the screw to help
guide the jaws. Steel vises are also
available with double screws or with a
quick-action screw. The quick action
allows you to turn the screw part of a
turn (or pull a lever) and slide the jaw
freely in or out. While this is a handy
feature, these vises are more expensive
and more likely to wear out if stressed by
heavy clamping pressure. On any metal
vise, adding a bigger piece of hardwood
to the movable jaw will spread the
clamping pressure over a wider area,
making it less likely to damage the work
and easier to clamp larger pieces.
END VISES
An end vise is the real workhorse of any
bench. With dog holes spaced down the
length of my bench, I can clamp work on
the bench surface as short as a few inches
or as long as 7 ft.-boards, tabletops,
doors, or round parts. My end vise is
based on the Ulmia design, constructed
from purchased steel mounting hardware
and a large steel bench screw (see the
photo at top). Turning the screw in or
out moves a section of the right end of
the bench with a wooden bench pin or
dog in any of four dog holes. The work is
clamped between this dog and another
in a dog hole somewhere along the
length of the bench. The movable jaw
also creates a small but powerful vise
within the thickness of the bench. Lined
with thick leather, this is a stout vise for
holding curved chair parts or narrow
boards vertically. The entire end vise
might look simple enough, yet it took me
An end vise and a
row of dog hol es
down the l ength of
the bench are useful
for hol di ng work
fl at on the bench
surface. Bui l t i nto
the bench, the
movabl e jaw al so
makes a powerful
vise for cl ampi ng
such t hi ngs as
curved chai r parts.
A large end vise
wi th two bench
dogs and a doubl e
row of hol es down
the bench can
cl amp l arge or
oddl y shaped parts
securely. The pl ane
on the bench is
an experi mental
Stanl ey bl ock pl ane.
as long to build and fit as the entire rest
of the bench.
The real versatility of an end vise is the
way the dogs can be positioned to hold
irregularly sha ped work, or any work for
that matter. The dogs clamp the work
piece between two points and near the
H O W T O P L A N E 79
bench edge so that it is easy to position
your body over the work and apply force
to the plane. To hold very large work
such as a tabletop securely, I often use an
additional clamp somewhere along the
bench, out of the way at the back edge if
possible. Some benches overcome this
problem by having two rows of dogs and
an end vise more like an extended side
vise with double screws and double dogs
(see the bottom photo on p. 79).
If you don't have an end vise, it's
useful to have a side vise with a bench
dog in the movable jaw that can be
pushed up or down. This is a common
feature on many cast-iron vises, as shown
in the top photo at right. Mounted in the
usual position as an end vise (on the
right-hand side, parallel with the end)
and used in the same way, a dogged side
vise can clamp long boards or parts along
the bench top against another dog
mortised into the bench top. With the
addition of a hold fast or clamps you can
probably get by, though it's still not as
useful or powerful as an end vise for a
wide variety of clamping jobs.
With both an end vise and a side vise,
your bench will be as versatile a clamping
jig as your imagination allows. While it
would be impossible to explain all of the
many ways you could clamp something
with these two vises, some of the typical
ways that work for me can be seen in the
"shop" photos throughout the book.
Choosing the best clamping method
depends on the amount of stability
desired, the effort involved with
clamping and unclamping, and personal
choice. Most of the best methods use
bench dogs or stops of some kind for
their sheer ease and simplicity.
DOGS AND STOPS
A bench dog is a wood or metal pin that
slides into a dog hole or mortise in the
bench. Traditional dogs are square in
cross section, measuring an inch or so on
80 C H A P T E R F I V E
each side. Today they are just as likely to
be round and fit into easily drilled round
holes. A small friction spring of some
type keeps the dog at any position above
the bench surface or pushed out of the
way below the bench top. Dogs are
typically used in pairs-one fixed in an
end vise and the other movable into any
A si de vise wi th a
pop-up bench dog
can serve as a
versati l e end vi se.
Wooden bench
dogs are si mpl e to
make and replace
and are less l i kel y to
damage a pl ane
i ron than ones of
steel or brass. An
ash str i p set i nto a
saw kerf or screwed
on creates a spri ng
to hol d the dog
i n posi ti on.
dog hole along the bench surface. The
photo above shows some simple wooden
designs with an ash spring either screwed
on or glued into a kerf.
Metal bench dogs have never appealed
to me-I see only the potential of running
onto one with a newly sharpened iron.
When planing thin stock the tops of the
dogs are close to the surface being
planed, so close that occasionally my
wooden ones will get an end-grain
shaving or two taken off. Metal dogs stay
sharp and square long after a wooden
dog is worn, but, then, it only takes a few
minutes to make a new pair of wooden
dogs. If you insist on using metal dogs,
choose softer brass over steel.
Bench stops look and work similarly
to dogs, except that they are more often
set in one position on the bench and are
used alone. One form is a 1 Vz-in. by
2 Vz-in. aluminum plate set flush with
the benchtop that can be flipped up to
provide a secure stop to butt the work to
and plane against. A toothed edge helps
hold the work securely. Another form is
forged like a bench dog with a flaring,
toothed top. Using either type stop can
be a very efficient way to hold narrow
boards when planing them, since no
vises need to be screwed in or out. My
bench doesn't happen to have a special
stop; when I want to plane against a
single stable point I use either of my
wooden dogs or shape one specially to fit
the work. A small brad set into the dog
II t \

(with the head nipped off) helps hold

the work from slipping side to side.
There is another type of bench dog
worth knowing about for turning any
plank into a bench for quick planing jobs
on the job site. These dogs are shaped in
a variety of ways, but usually with three
Bench stops, such as these from an earl y
Hammacher Schl emmer catal og, morti se
into the benchtop and can be pushed up as
needed. Teeth hel p hol d the work.
pointed legs-something like a trivet (see
the photo below). Driving two legs into
the plank stabilizes the third leg, which
can be used like a stop, or another dog can
be driven in to hold the other end of the
board, too. These dogs are light, compact,
and very handy.
WEDGING STOPS
AND J IGS
Holding the end of a board on top of a
bench to edge-joint it or plane upon it in
some way poses a challenge that has
sparked much creativity. Some designs
hold the end by wedging it into a jig that
has become known as a wedging stop.
The most versatile ones adjust to a range
of board thicknesses. Why use a wedging
stop when a side vise would be more
positive and maybe even easier to use?
The beauty of a wedging stop is its
Forged-i ron bench
dogs can turn a
pl ank i nto a qui ck
pl ani ng bench.
H O W T O P L A N E 8 1
We d g i ng S t op s
In this simple design, the board is held in
place by a V-notch cut into a block.
Stop
In this li esign, the board is
held in place by a loose,
stepped wedge.
End view
simplicity; the work needs only to be
jammed into the stop to be adequately
held. Wedging stops work best for
planing small parts of a uniform size
where the support of a flat bench helps,
for planing irregular shapes where the
stop can be cut to ft the work, or for
use as a temporary stop on the job site
easily cut and nailed to a plank. To hold
specially shaped parts such as delicate
window muntins when planing against
a stop, a useful addition is a planing
jig to fit the individual pieces into.
Used together or alone, either a wedging
stop or a jig can make some planing
work easier.
82 C H A P T E R F I V E
The simplest wedging stop is no more
than a block with a V-notch cut into it.
The board end is jammed into the V to
hold it. Another variation uses a stepped
wedge both to stop and clamp the end.
Many versions were made from cast iron,
most of which can be reproduced just as
well in wood. The drawing above shows
two very practical designs. The variations
are endless, limited only by your specific
needs and imagination.
HOLDFASTS
A holdfast is a hefty L-shaped steel
forging that's useful for holding work on
top of the bench (or along an edge in
place of a board jack). One end wedges
into a hole drilled through the bench top
and the other holds against the work (see
the top photo on the facing page). The
beauty of holdfasts lies in their ability to
be adjusted easily and to hold oddly
shaped objects. A solid hit with a mallet
sets the holdfast; a hit to its back releases
it. Inserting a small block of wood under
the clamping face will protect the work
surface and can be shaped to fit it. The
only limitation to a holdfast is that it can
be used only where there is a hole drilled
to receive it, which is not always exactly
where it might be needed. Nevertheless,
as a "third hand" holdfasts are very
useful to help hold large surfaces such
as tabletops.
Hol dfasts work as thei r name i mpl i es, with a l ong reach, secure hol d,
and qui ck rel ease. Al l they requi re i s a hol e through the benchtop.
A modern reincarnation of the
traditional hold fast looks like half a
clamp set perpendicular to the
benchtop. While it might be versatile
and useful, it has the same limitations as
a forged holdfast-it is movable only to a
point. A short bar clamp securing the
work somewhere along a bench edge can
be just as useful.
CLAMPING BOARDS
FOR EDGE JOINTING
Short boards are fairly easy to clamp in
a side vise. I have an old cast-iron side
vise with a jaw about 5 in. deep that can
hold boards (or thicker planks and
wider parts, too) up to about 4 ft. long.
The advantage of using a side vise rather
than just the top of the bench with a
stop is that the side vise holds the work
securely regardless of whether the
bottom side is shaped, rough, or uneven.
The jaws merely clamp the work in
position. A side vise has the added
benefits of holding a board more rigidly
on edge than you would be able to on top
of a bench and at a good working height.
Short boards up to
about 4 ft. l ong can
be cl amped in a
si de vi se. The
stronger the vise
and the larger the
jaws, the l onger the
board i t can hol d
securely.
H O W T O P L A N E 83
Long boards can
be secured usi ng
both a si de vise and
a bl ock of wood
cl amped i n the end
vise. A second
bl ock of wood
cl amped mi dway
between the vi ses
supports narrow
and fl exi bl e stock
for the most accurate
joi nted surface.
Longer boards are hard to clamp
securely in a side vise alone. One
solution is to use both the side vise and
the end vise. I clamp a short board low
down in the jaws of my end vise, so that
it sticks out perpendicular to the front
edge of my bench 4 in. or so and forms a
rest for one end of the board (see the
photo above). The other end of the board
is clamped in the side vise. Clamped in
this way, the edge of the bench lends
support and the side vise holds the board
in position. If the board is so narrow that
it might deflect from the planing
pressure, an additional block or two
clamped to the face of the bench will
further support the board. The same
thing can be done with a short bar clamp
securing the board right to the edge of
the bench, but this method requires
extra clamping and unclamping for every
piece. Between the two vises I can
comfortably joint boards about ] ] ft.
long, although if I were working such
long lengths regularly, I would build a
longer bench.
If you joint wide boards regularly, it's
a good idea to incorporate a board jack
into your bench (see the photo on p. 74)
or build a portable one. A board jack is a
84 C H A P T E R F I V E
board mounted on the side of the bench
(some of them slide down the bench to
accommodate boards of different
lengths), with spaced holes to hold a
stout peg at various heights off the floor.
One end of the board to be jointed rests
on the peg; the other end is held in the
side vise (see the drawing below). A
board jack is an adjustable version of the
holding method I use with a block
Using a Boar d Jac k
clamped into the jaws of the end vise.
The simplest board jack need be no more
than a row of peg holes down the leg near
the end vise or a few larger holes for a
holdfast. A porta ble board jack resembles
a stairs cut into a board supported
vertically on a base of some kind.
So far I haven't gotten around to
building either a fixed or portable board
jack. This has meant using extra
Si de
vise
Adjustable peg holds
the board at the desired
height for planing.

--. -- -
- --
creativity when planing the edge of a
wide tabletop or jointing a wide board.
What works is to clamp one end in the
side vise and prop the other end on
either a short piece of plank resting flat
on the floor or a lO-in. or 20-in. high
sawhorse. Naturally I choose a height
that puts the edge I am working on
parallel with and slightly above the
bench surface. A bar clamp at the tail
vise end helps stabilize the work if I
need it. It's a simple solution, but sturdy
and effective.
Adjusting the Plane
for Work
You've got the work clamped in place at a
good working height. Your plane is
tuned, the iron sharp, and you're ready
to start curling up those long-awaited
shavings. But before you put the plane to
the wood, hold on just a half-minute and
check that the throat is not too tight or
wide for the work you want to do, that
the depth of the iron is set properly, and
that the iron is parallel with the sole. It
doesn't take much time working with a
plane before these adjustments become
second nature-a glance at the throat and
a light touch with a finger to feel the
iron's depth and alignment in about as
much time as it takes to pick up the
plane and bring it to the work.
THROAT OPENING
Chapters 3 and 4 explain in detail how
the throat opening affects the physics of
the cut and how to adjust the opening
properly. The truth is that unless you
are trying to use only a few planes for all
of your planing work, the throats will
rarely need to be adjusted. With a
handful of planes tuned and at the ready,
you'll quickly learn which one works
best for what you are trying to do. The
throats should range from wide for
planing coarse shavings and removing
wood quickly, to very narrow for light
polishing cuts.
The problem you are most likely to
encounter is clogging, which occurs
when the throat is tight and you try to
take too heavy a cut. For day-to-day work,
set the throat on your bench planes
(except smoothing planes) between
'.:in. and '.in. An opening this wide
is a fine compromise between good
performance and being able to cut
shavings of different thickness. Moreover,
the deeper the iron is set, the more
throat width it takes up. Set the throat
slightly wider on a plane you expect to
use just for rough work and really
hogging off wood quickly. A little tea rout
and roughness of the surface are to be
expected, and at least the plane won't
clog because the throat is too small. For
smoothing planes and other planes
(shoulder, bullnose) tuned to cut a fine
shaving, a fine throat is a must to cut
with a lot of accuracy and leave a
polished surface. Set these throats as
fine as you can-just shy of
'
+in.
Occasionally I do change the throat
width on my few adjustable-throat block
planes. Used on end grain a modest
throat is fine, but using the same plane
to level the transition between stile and
rail on a door, for example, I want the
throat tight. The only other time I would
change the throat opening would be if I
were about to joint a number of curly
maple boards. The little time it takes to
move the frog and tighten the throat on
my Stanley Bed Rock #607 prevents a lot
of frustration.
IRON DEPTH
Once the throat opening is checked, next
adjust the iron's depth for the work you
expect to do. Cast-iron planes couldn't
be easier to use when it comes to making
this adjustment; I'm sure it was a factor
in their immediate acceptance and
popularity over wooden planes. A half
turn on the adjuster wheel and the iron
is set deeper, or it can be backed out just
as easily with a half turn the opposite
way. The rotary motion of the adjuster
wheel pushes or pulls the Y-adjustment
Adjust the depth of
the iron in a wooden
pl ane by tapping on
the toe for a deeper
cut or on the heel
for a fi ner cut. Hi t
the strike button i f
there i s one.
H O W T O P L A N E 85
Movi ng the adjuster
ri ght or left on a
Bai l ey-pattern bench
pl ane ti l ts the i ron to
al i gn it paral l el wi th
the sol e. Look for
an even gl i nt of
the iron or feel for
its al i gnment wi th
a fi nger.
To adjust lateral
al i gnment on a
wooden pl ane, tap
on ei ther si de of the
iron to al i gn it wi th
the sol e. Here, the
author feel s the
al i gnment wi th hi s
thumb as he taps
the i ron.
lever that in turns slides the iron in or
out. The only aspect that is slightly
confusing is that on most bench planes
turning the adjuster wheel in backs out
the iron. Turning the wheel out deepens
the cut. Start with the iron set for a light
cut and make sure to take any backlash
out of the adjuster so there is slight down
ward pressure on the iron (see p. 72).
Once you have made a shaving or two
and seen how the wood behaves, you can
always deepen the cut.
86 C H A P T E R F I V E
Adjusting the iron's depth in wooden
planes takes a little more practice to
develop a feel for what's happening-it is
more akin to tuning a fine instrument
than the purely mechanical adjustment
of a metal plane. (Of course, some
modern wooden planes and all transi
tional planes have an adjuster similar to
cast-iron planes and are adjusted the
same way. ) For all-wood planes, tapping
on the toe sets the iron for a deeper cut;
tapping on the heel raises the iron for a
finer cut (and will eventually release
the iron and wedge if hit ha rd enough).
If there's a strike button on the heel, hit
it there (see the photo on p. 85). On
better-quality, long bench planes there is
also a strike on the top of the toe end of
the plane. Tapping this strike also
lightens the cut. One school of thought
maintains that all adjustments should be
made with a wooden mallet and the iron
shouldn't be hit at all, but a good look
at any well-used plane will show that this
is not always the case. I use light blows
with a smooth-faced hammer (as the
Japanese do) to tap the iron lower for a
more aggressive cut.
Unfortunately, adjusting the iron
depth in a wooden plane is not quite as
simple as a few taps here or there.
Lightening the cut of the iron also
releases some of the pressure of the
wedge, which will need to be tapped
back snug (don't drive it too hard or you
may distort the plane body or crack out
the cheeks). Yet in setting the wedge, the
iron is often set slightly deeper as well.
Once you've gotten used to the feel of the
way the plane reacts to being tapped, it's
really no more difficult than adjusting a
metal plane.
LATERAL ALIGNMENT
Setting the iron parallel with the sole
the lateral alignment-is just as
important as setting the iron's depth.
If the iron isn't parallel, one side will cut
more deeply and either gouge the surface
or, in the case of jointing an edge, cut the
edge with a slight bevel. It's easy enough
to sight down the sole from the toe and
see how parallel the exposed edge of
the iron and the sole are, and if need be
make an adjustment. In the early
development of the cast-iron plane there
was no simple way to adjust the iron
laterally, save for just pushing it one way
or the other. After 1 885, Stanley's Bailey
line of bench planes had a lever for
lateral adjustment of the iron.
On cast-iron bench planes the lateral
adjustment lever is behind the iron and
attached to the frog. Moving it right or
left rocks the iron slightly. The problem
is that on some planes the lever tilts the
iron exactly the way you predict it
should, and on others the iron moves in
the opposite direction. On bench planes,
moving the lever to the right (sighting
along the sole from the toe with the
plane upside-down) generally withdraws
the right corner of the iron. Moving the
lever to the left withdraws the left corner
of the iron (see the top photo on the
facing page). This is the opposite of what
intuition tells you to expect. On other
bench planes and many block planes
everything is reversed. It sounds more
confusing than it is. Eventually you'll not
even look at the iron, but feel its depth at
a few places with your finger and make
minor adjustments of the lateral adjuster
without even thinking.
or skiing than football. To plane well
demands aligning yourself in a
comfortable stance and balancing your
body through the stroke, all the while
applying pressure to and controlling the
plane. Such a thing really can't be taught
any more than you can teach a person to
be a good skier by explaining the way to
balance and move your body over your
skis. Explaining the dynamics of the
technique is a good first step, with
sensitivity and true understanding of it
coming through time. For the less
experienced, your first plane strokes will
feel awkward. For the more experienced,
perhaps being conscious of the way you
balance your body and direct force to the
plane will make the work less tiring and
more rewarding. As with any skill, it
takes time to develop a feel for the
subtleties of the tool.
To adjust the iron laterally in a wooden
plane, tap the iron to one side or the
other, as shown in the bottom photo on
the facing page. In this case, the iron does
adjust the way you might expect-tapping
the iron to the right lowers the right
corner. Bear in mind that adjusting the
lateral alignment might change the iron's
depth setting, so give it one last check
before starting to plane.
Planing Technique
Learning how to plane comfortably and
efficiently is no different than learning
how to master any physical activity
except that planing is more like Tai Chi
R E A D I N G T H E G R A I N
I
wish there were some easily headed toward the cut surface, If you've used a machine to
followed rules for reading rather than down into the surface a board before hand-
the grain of a board and wood, which would be the planing, it's a lot easier to tell
knowing the best way to plane case when planing against the which way to plane. My
it, but unfortunately there grain. Unfortunately, few normal procedure is first to
will always be a fair measure of woods are straight-grained, and run a surface over a jointer
guesswork involved. I can look on most boards the grain rises after looking at the grain and
at the grain lines on the and falls in such a way that picking an orientation. If the
surface of a board and inspect somewhere along its surface first pass leaves a smooth
the two edges and feel you're apt to be planing surface, I'll mark an arrow on
confident that I'm going to be against the grain. What makes the wood and go on to the
planing "with the grain" but things even more difficult is planer. If not, I'll try the
quickly come to find out that irregular grain (which appears opposite direction. Sometimes
things aren't what they appear as figure), imperfections (such it's a toss-up between the two,
to be when I get deep tearouts. as knots), and the naturally in which case I know I'll be
The ideal technique is to inconsistent structure of some cautious when hand-planing
plane the wood fibers in the woods (such as roey, curly, or later. The machining arrow
direction that they appear to ribbon striped). The best you stays on the surface or edge
rise in front of the plane. Any can hope for is to make a good right up until I remove it with
splitting out of the fibers is guess and start in cautiously. a plane.
On any board, look at
adjacent surfaces (a face and
an edge) to get a better idea of
how the grain is oriented. The
more consistent the grain lines
on both, the more likely the
planing will be smooth and
easy. Watch out for swirled or
circular grain lines; these lines
indicate the rising and falling
grain around such areas as
knots. Some boards have
broad U-shaped, grain lines:
plane into the Us as if the
grain were a topographical
map and you were working up
a valley. Look at all four edges
if need be and start with a
light cut.
H O W T O P L A N E 87
A comfortabl e,
relaxed stance whi l e
pl ani ng, wi th your
shoul der over the
work, al l ows you to
del iver power and
control to the pl ane.
Hol d the pl ane with a relaxed but fi rm gri p, graspi ng the front knob
wi th a few fi ngers and the rear tote wi th as many fi ngers as fi t around
it comfortabl y. Use your i ndex fi nger to adjust the depth of the i ron
on the fly.
88 C H A P T E R F I V E
The most important part of the
planing stance is that it feel comfortable
and natural. Assuming that you are
about to joint a board clamped to the
bench planing from right to left, a good
stance would be with your legs apart as
wide as a stride, with your right foot
back and left foot forward (see the photo
at left)' This stance puts your shoulder
over the work and, if the bench is a good
height, your upper body in position to be
able to deliver to the plane the power
and control necessary. Flexing the knees
gives you the balance to rock backward
when starting the cut and also to lean
forward to finish the stroke.
The way you hold the plane should
be comfortable, too-a tight grip is tiring.
I grab the front knob on bench planes
between the thumb and first one or two
fingers of my left hand. The high front
knob common on later Bailey-type planes
is especially comfortable. This grip leaves
two fingers free to wrap around the
plane's side to guide the plane along the
board for extra control when jointing
(more on this in Chapter 6). I grip the
rear tote with my thumb and three
fingers, leaving my pinkie or index finger
to lie along the plane's right side. This
grip gives a little added control and is
more comfortable than trying to jam all
of my fingers around the tote. While
holding the plane I can use my index
finger to rotate the depth adjuster if I
want to make an adjustment on the fly
(see the photo at left)' Wooden planes
and unhandled planes are held in
basically the same way, with the right
hand at the heel and the left hand at the
toe. Position your hands and fingers in
whatever way feels most comfortable so
that you can apply pressure to the plane
and control its direction easily, too.
Feeling a natural start and ending to
the plane stroke is the hardest part of
planing technique to master. It's very
Start the cut by
bal anci ng the pl ane
wi th the i ron ready
to cut. All of the
pressure is at the
front of the pl ane;
the rear hand onl y
hel ps bal ance the
pl ane at the start of
the cut.
Pressure the pl ane evenl y t hrough the cut, usi ng both hands for
bal ance and control .
End the cut by shifti ng the pressure toward the heel to avoi d roundi ng
over the end.
easy to tip the plane down at either end
and cut more deeply so that before long
you have a jointed edge with a slight
curve, not one that's truly straight.
Think of the sole in front of the iron as
guiding the beginning of the cut. At the
start of the cut I position the plane on
the board with the iron just about to
make contact (see the photo at top). My
left hand on the front knob exerts firm
pressure downward, as my right hand
merely supports the heel of the plane.
Holding the plane at a slight skew feels
more comfortable and helps the cutting
dynamics by slicing the iron into the cut.
As the plane starts to cut, I gradually
shift pressure from the front knob to the
rear tote so that by the time the sole is
fully supported the pressure is equal (see
the photo above left), By then the plane
has a certain momentum that I try to
maintain through the entire cut, not fast
but steady. For long boards I have to take
a step or two forward, still keeping my
shoulder positioned over the work and
the pressure even. It takes a bit of
practice to keep the plane steady as you
H O W T O P L A N E 89
R A Z E E P L A N E S
R
azee planes are
interesting wooden
planes that have a unique
design. Part of the plane stock
is cut away and lowered at the
rear where the tote is joined
(and sometimes at the front
knob as well). This design
gives the plane better balance
and control by lowering its
center of gravity and by
aligning the pushing force
right behind the iron and
close to the cutting action.
The razee style has always
been associated with the jack
plane and longer ship planes,
made of tropical hardwoods
and usually narrower than
conventional bench planes.
Although ship carpenters
didn't invent the form, they
took the name from the
description of a ship with an
upper deck removed. Razee
planes were also used in trade
schools, where a slightly
lighter and easier-to-control
plane presumably helped
students learn planing
technique. Although not rare,
razee planes are not common
either. The reason for this is
more likely their higher cost
(for fitting the tote into the
step in the stock) than their
lack of appeal and usefulness.
Razee handl es lower the pl ane' s center of gravity and del i ver the force
of your hand ri ght to the cutti ng acti on of the pl ane.
90 C H A P T E R F I V E
move your body forward, but with a
heavy jointer the mass of the plane helps
a lot. If for some reason the plane clogs
with shavings or it feels as though greater
force is needed to drive the plane, stop.
Chances are the iron is set too deeply.
Reading the troubleshooting section on
the facing page might help, or recheck
the tuning as explained in Chapter 4.
The cut should feel smooth and
continuous from end to end.
Ending the cut is the reverse of
starting it: You need to shift the pressure
toward the heel as the sole extends
beyond the end of the board. By the time
the iron stops cutting, all the pressure
should be on the heel. Sometimes just
before this point I take my hand off the
front knob and let the mass and
momentum of the plane finish the cut
(see the bottom right photo on p. 89).
Try to avoid the mistake of keeping
pressure on the toe and cutting more
heavily at the end of the stroke. A long
plane and the design of the iron forward
of center help avoid this, but it is still
easy to round over the end of the cut.
A natural tendency at this point is to
slide the plane back before picking it up
to start another stroke. Don't, because it
will unnecessarily dull the iron. Always
pick up the plane at the end of the
stroke. Even the heaviest plane can be
picked up one-handed if the balance is
right. Ending the stroke is a good time to
clear the throat of any shavings to
prevent clogging. Very shortly, picking
up the plane to start another stroke and
clearing it of shavings will become
second nature.
If you're done planing or are pausing
to sight the planed edge, always lay the
plane on its side on the bench or rest the
toe on a thin scrap of wood so that the
cutting edge is off the bench. It's far too
easy to nick or dull the iron by carelessly
setting it on the end of a steel rule or a
bit of hardware lying on your bench.
SKEWING
I've always found that it feels natural to
hold the plane at a skew or an angle to
the direction of the stroke while planing
along (as shown in the bottom photo on
p. 88). It's a good habit to get into,
because skewing can noticeably improve
the cut. The physical reasons for this are
explained in Chapter 3: Skewing lowers
the effective cutting angle of the iron,
provides additional slicing force, and
reduces resistance to the cut. The more
extreme the skew, the easier and better
the cut will often be; but the width of
the cut will be a lot smaller, too.
Except when using molding planes
or a jointer gauge (see pp. 108-1O9), I
always keep the plane at a slight skew
when I'm planing. I even skew a jointer
plane, although with this long plane I
have to be aware of keeping the entire
length of the sole supported on the
work. Around knots and unruly figure,
skewing the plane one way or the other
never fails to yield a smoother surface.
When planing a tabletop or any large
surface, skewing helps me smooth
transitions at glue joints and areas where
the grain is inconsistent. I think of
skewing much the same way my
workhorse thinks about hills; when he's
given a choice he'd much rather skew
around a hill than climb straight up it.
TROUBLESHOOTING
No matter how well you learn planing
technique, at some time you are likely to
encounter annoying problems. Three
common problems are uneven cutting
or "chatter," a clogged throat, and a
misaligned iron that leaves distinct
ridges. There are simple solutions for all
three problems.
Chatter
Chatter shows up as ripples in the
surface where the plane iron stuttered
and didn't cut smoothly. It can often be
as easily felt or heard as seen. Very often
chatter will occur at the start of a cut,
before the plane is firmly supported on
the surface. The uneven cutting is caused
by the buildup of pressure against the
iron to the point that it starts to vibrate.
As the iron springs forward and back,
the cutting depth is raised or lowered
slightly, enough to leave distinct parallel
cuts in the surface.
The key to reducing chatter is to
reduce some of the pressure on the iron,
or give it more support. The simplest
solution is to use a thicker, more stable
iron. Alternatively, you can skew the cut
to reduce pressure on the iron, or take a
lighter cut. To make sure the iron is
getting adequate support, check some of
the tuning: Is the bed flat and even, is
the cap iron fitted to the iron, is the frog
adjusted too far forward so that the iron
has little support near the cutting edge?
It may be a combination of things. If you
reread the tuning sections in Chapter 4,
you should be able to solve any one of
these problems.
Clogging
Clogging can sometimes be a problem
even with the best tuned planes.
Shavings bind up so tightly in the throat
that the plane no longer cuts. The most
obvious cause is that the throat is too
tight. The solution is to open the throat
or back off the cap iron a '.-in. or so.
Nothing clogs up a plane faster than a
dull iron. To compensate you take a
deeper cut because the plane doesn't
seem to be cutting, and then you're done
for. Clogging can be caused by a poor fit
of the cap iron to the iron, which allows
some shavings to get under it and others
to build up. The cap iron should be
smooth and waxed. The wedge in a
wooden plane might be somehow
blocking the free escape of the shavings.
Bevel the front edge of the throat
forward slightly to give the shavings extra
room. A lighter cut always helps, but just
expect that sometimes clogging is going
to be a problem.
A lot of the clogging problem can be
eliminated by clearing the throat of large
shavings at the end of each stroke. Often
this means nothing more than pulling
out the end of a long curl. Why else do
you think the upper edges of the throat
on wooden planes are chamfered?-to
make it easier to get your fingers in to
pull out the shavings.
Iron misalignment
Slight lateral misalignment of the iron is
rarely much of a problem, but it can be
an annoyance and is something to be
aware of. If the iron isn't parallel with
the sole, one side cuts more deeply and
leaves pronounced ridges. If I'm rough
surfacing a board, a little unevenness
isn't a problem. But for a final smoothing
I want the iron parallel to the sole. I
usually feel the depth of the iron
projecting from the sole in a few places
before starting in, and, if need be, make
slight adjustments. By watching the
thickness and width of the shavings
while planing, I can make further
adjustments as necessary. Ideally, I want
to see a shaving of consistent thickness
curling nearly the width of the throat.
Learning to use a plane takes practice.
With the work held securely on a bench,
the plane tuned and adjusted, it's just a
matter of time before planing becomes
a natural extension of your body
motion. In time, you'll find yourself
concentrating more on feeling the way
the plane cuts, on the beauty of the
surface, and on the texture and smell of
the shavings.
H O W T O P L A N E 91
PLANES F OR TRUING
AND S IZ ING S TOCK
Crftsmanship is a combination of knowledge on how to use tools and
of skill with the hands.
-Stanley Rule and Level, How to Work with Tools and Wood, 1 927
No planes are more useful or used
more often than planes for truing and
sizing stock, commonly known as bench
planes. Before the development of wood
working machinery and its adoption in
almost every shop, bench planes did
much of the work that we rely on table
saws, thickness planers, and jointers for
today. With machines taking over the
hardest tasks of working rough stock to
dimension, bench planes are more often
used today to refine parts at the bench.
Even in a shop full of power machinery,
it's hard to imagine not having a bench
plane or two in your toolkit.
Types of
Bench Planes
When most of us think of bench planes
we think of Stanley cast-iron planes, or
more exactly Bailey-pattern bench
planes, since it was Leonard Bailey who
patented most of the ideas over 1 25 years
ago (see Chapter 2). But for all of the
hundreds of years before Stanley and
others perfected cast-iron planes, bench
planes were made of wood (see the photos
on p. 94) and more rarely of joined steel
plates with wood infill. Most craftsmen
had at least three bench planes: a jack
This lid from a j oi ner' s chest, probably made i n London c. 1 790, depi cts
the maker at hi s bench and shows off hi s consi derabl e i nl ay ski l l s and
col l ecti on of bench pl anes. ( Photo courtesy Col oni al Wi l l i amsburg. )
plane for rough-dimensioning work, a
jointer or try plane for shooting edges
and accurately flattening panels, and a
smoothing plane for finishing surfaces.
They were the hardest working planes he
owned. Although some modern-day
craftsmen still prefer to use wooden
planes, many more feel that cast iron and
steel are superior materials for making
bench planes.
93
We wi l l probabl y
never know why the
maker of thi s frui t
wood French try
pl ane carved a fox
head into the pl ane
body, as wel l as
hi s i niti al s and date
( " M S. 1 834") , but
it i s typi cal of early
European pl anes.
Ori ental bench pl anes have thi ck i rons and white-oak bodi es. Noti ce the sl i di ng dovetai l ed
" key" to ti ghten the throat on the pl ane shown upsi de-down.
94 C H A P T E R S I X
STANLEY
BENCH PLANES
Stanley cast-iron bench planes range
in size from the smallest # 1 to a #8
jointer, and also include scrub planes
(see pp. 97-99) and block planes (see
pp. 1 10- 1 1 9). Besides these sizes there
are a few odd sizes, a #4
1
/2, a #5 \2, and a
#5 '+.Then there are some specialty
planes that could easily be included in
this group, such as the # 10, # 10 \2, and
# 1 01/4 bench rabbet planes. For the sake
of simplicity these rabbet planes are
included in Chapter 7; this chapter
focuses primarily on the basic bench
planes used to surface and size stock.
Stanley was by no means the only
manufacturer of bench planes, but it's a
measure of Stanley's dominance of the
market that its numbering system has
almost become the standard. Lots of
other manufacturers made bench planes
(some were even made by Stanley and
sold under other names), but no matter
what their catalog numbers, we still
think of them as #4s or #6s, and so on.
To avoid confusion, I'll stick with the
Stanley numbering system.
Despite their obvious differences in
size, Bailey bench planes are nearly
identical to one another in design (see
the chart on p. 96 for a comparison of
sizes). Of all these planes, the # 1 is the
least usable and the most highly sought
after. To me, it's a curiosity-a miniature
bench plane without any lateral
adjustment. Certainly it can be used to
dimension parts, but the sole is short
and the handles so tiny that using it is
more awkward than using a block plane
the same size. One story why Stanley
and its competitors made such small
planes was for schoolboys and for use in
woodworking schools. The # ] might
have been made for small hands and fine
work, but I suspect its popularity then or
now has more to do with our fascination
The Stanl ey #1
(atop the box) i s the
smal lest and most
rare of the bench
pl anes. Competitors
such as the Uni on
Manufacturi ng Co.,
of New Bri tai n,
Connecti cut, made
a si mi l ar-sized pl ane,
a #0 (foreground) .
The Stanley #4%
i n the background
gi ves a sense of
thei r ti ny size.
Three early cast-i ron
bench pl anes
i ncl ude (from rear)
a Chal l enge joi nter
sol d by Tower and
Lyon, patented 1 883
with an i nteresting
depth adjuster, and
a #5 and a #4 Vi ctor,
a l i ne of pl anes
ori gi nal l y made by
Leonard Bai l ey
and l ater bought
by Stanl ey.
P L A N E S F O R T R U I N G A N D S r Z I N G S T o e K 95
Bai le y Cast- I r on Benc h Pl anes
SIZE* NAME I RON WIDTH LENGTH WEI GHT
(in.) (in.) (lb. )
# 1 Smoot hi ng 1 1/4 5
1
/2 1 1/
8
#2 Smoothi ng 1 % 7 2 %
#3 Smoothi ng 1 % 8 3%
#4 Smoothi ng 2 9 3%
#41/2 Smoothi ng 2% 1 0 4%
#5 Jack 2 1 4 4%
# 514 Juni or jack 1 % 1 1 1/2 3%
#51/2 Jack 2 1/4 to 2% 1 5 6%
#6 Fore 2% 1 8 7 %
#7 Joi nter 2% 22 8%
#8 Joi nter 2% 24 9%
#9 Cabi netmaker's 2 1 0 4%
bl ock pl ane ( 81/4 after 1 936)
#40 Scrub 1 1/4 91/
2
2 %
#401/
2
Scrub 1 % 1 01/2 2 %
*Bench planes with corrugated soles (available for all but #1) have the letter C
after the number (e.g., #2C, #3C).
Adapted from Sellens, The Stanl ey Pl ane (1975).
96 C I I A P T E R S I X
with anything miniature. Certainly
someone interested in actually using a
#1 won't pay the nearly $ 1,000 they can
trade for.
I know there are some who would
disagree with me, but I fnd the #`and
#
3
bench planes equally small and only
somewhat useful. I'm sure there is fine
work they are well suited for-leveling
the top edges of small drawers, for
example-but I find that it's just as easy
to have a #
4
tuned for this work and a lot
more besides. For me, the #
4
is the
perfect size; it fits my hand, the sole is
long enough to do accurate work, it has
enough heft to plane well, yet I can use it
one-handed if need be. It's my "odd-job"
plane, used for trimming parts to size,
cutting tapers or bevels, shooting small
edge joints, or performing any of the
varied planing work in my day.
There are four more common sizes of
bench plane, each progressively longer
and heavier: a #:jack, a #6 fore, and
#
7
and #cjointer planes. The odd-sized
#
4
'.,#: '.,and #: '+ are just what you
would expect, intermediate sizes. Which
one of any of these planes you choose
depends upon the work you want to do
and which one has the heft and feel that
most appeals to you. Often it is as much
a matter of habit as which one fits the
work. Some craftsmen tell me they use
a #7 for everything. Such a long plane
can do accurate work, but I find it too
heavy for odd jobs at the bench. Instead,
I use both a #
7
and a #cfor jointing
long edges and planing surfaces that I
want very flat. I rarely use a #6, but use a
#:almost as much as a #
4
, for jointing
Thi s assortment of bench pl anes is typical
of the range of sizes once avai l abl e, from the
smal lest #1 to a #8 joi nter.
short edges, planing end-grain edges
(as on a tabletop), and fitting drawers
to their openings.
There are no hard-and-fast rules
about which planes to use, but the
design of each evolved for certain kinds
of work. Use the plane that fits the scale
of the work and use longer planes for
greater accuracy. This goes for anything
from shooting an edge joint to flattening
a surface.
SCRUB PLANES
Scrub planes are the hardest working of
the bench planes. Not so long ago they
were part of the basic toolkit of any
woodworker, used for roughing parts to
size before refining them with other
bench planes. You could think of a scrub
plane as the plane equivalent of a
thickness planer. Where parts could be
left rough, such as the underside of
drawer bottoms and case backs, you'll
often see the strong parallel corrugations
left by a scrub plane.
Three things distinguish a scrub plane
from other bench planes: The throat is
very large to pass coarse shavings, the
iron has a very pronounced curvature
or camber across the width of the edge,
and the iron is usually only a single
thick iron without a cap iron. All three
characteristics help the plane cut
aggressively without clogging, but with
little refinement of the surface. This is
called "hogging." With a cambered
cutting edge, the iron cuts like a large
gouge; in fact, the finished surface is apt
to be rough and looked gouged. A single
iron is easiest to set up and use, although
with a minimum of tuning a double iron
works fine, too. The slightly rougher
surface you get with a single iron is less
important than the ability to remove
material quickly.
Scrub planes are used far less today
than they once were. I use one when it's
easier than going to the bandsaw or table
saw, for hogging off wood when cutting a
tapered part, for beveling the underside
of a drawer bottom, or for thicknessing
the odd board that's too wide for my
planer. A scrub plane is also useful when
gathering materials for a project, for
choosing boards with consistent quality,
Common bench
pl anes such as the
#2, #3, and #4
shown here (from
rear) have i denti cal
adjusters, rear
handl es, lever caps,
and body shapi ng.
Scrub pl anes are
the hardest-worki ng
bench pl anes.
Shown here (from
rear) are a Stanley
#340 furring pl ane
wi th mi ni mal sal e for
"cl eani ng" rough
boards; a Sargent
# 1 62 wi th two
i rons and cast-iron
handl es for a sure
gri p; and Ohi o
Tool's #040, whi ch
i s nearl y i denti cal to
a Stanl ey #40.
grain, or color. With a scrub plane and a
minimum amount of planing through
the roughsawn or weathered surface, I
can get a good idea about the character of
a board before sending it over the jointer
and planer.
P L A N E S F O R T R U I N G A N D S I Z I N G S T O e K 97
Scru b planes can be found on the
used tool market, often priced quite
reasonably. They are apt to be worn, but
nothing that a little tuning can't remedy.
Lie-Nielsen makes a new cast-iron
version of the original Stanley #40 and
replacement irons, too. You might
consider making your own scru b plane
from either a worn wooden smoothing
plane or a tired #3 or #4 bench plane.
Wooden-soled transitional planes work
well, too. I have a couple of old wooden
smoothers that have throats so wide that
refashioning them as scrub planes is
about all they are useful for. A cast-iron
bench plane will work well as long as
the throat is opened wide and the iron
is cambered.
Tuning and using scrub planes
Scrub planes need a lot less tuning than
most planes. Tearout and surface
roughness are to be expected, so save the
time you'd spend tuning a scrub plane
for your smoothing or jointer planes.
Stick to the basics: Make sure the
handles are tight (you'll be applying a lot
of force to the plane and will want a good
grip), check that the sole is within the
ballpark of flatness in the important
areas, camber the edge of the iron, and
tune the screw cap so that it holds the
iron snugly in place. This is basic tuning
covered in Chapter 4.
If you are going to tune a # 4 or si mi la r
bench plane as a scrub plane, think
about it as a dedicated plane used for this
Ol d and worn wooden or transi ti onal pl anes can be tuned as scrub
pl anes by wi deni ng the throat and camberi ng the i ron.
98 C H A P T E R S J X
Camberi ng the iron al lows the scrub pl ane
to make deep gougi ng cuts. I f the pl ane has
a cap i ron, it can be set wel l back from the
cutt i ng edge (as shown) or ground to the
same camber as the i ron.
purpose only. Opening the throat wide
enough to work well as a scrub plane and
cambering the iron will make your plane
useless for more refined work. Start by
moving the frog well back to open up the
throat (refer to pp. 59-62 for more
detailed information on adjusting the
throat). You'll need a throat at least
'
s in.
wide-Yl6 in. wide would be even better.
When moving the frog, be aware of one
thing: The iron still needs to be bedded
well along its entire length. Move the frog
so the iron just beds against the beveled
sole. If the throat is still not wide enough,
file the front of the throat opening.
Cambering or shaping the iron is very
important to get good results. The iron's
shape concentrates the cutting energy
over a small arc, so it can cut more deeply
than a straight iron cutting along its
entire width. How much camber is a
matter of choice-the more you have, the
easier the tool will cut, but the smaller
the width of each "gouging" cut. You'll
need to resharpen more often too, since
less of the edge is cutting. A good
compromise is about Yl6 in. relief either
side of the center of the iron (see the
photo above and the drawing on p. 67).
I rough out the shape on the grinder, by
moving the iron in an arc over the wheel.
Drawing a reference line on the back of
the iron with a felt-tipped pen helps you
grind a more accurate shape, although
it's not vital that it be perfect. If the
plane has a double iron, the cap iron can
either be roughly ground to the same
camber as the iron, or be moved back
from the cutting edge, which will help
open the throat further, too.
Stanley made what they called a
furring plane (#340) that gives an idea of
how unimportant a long flat sole is to a
scrub plane. This tool (shown in the
bottom photo on p. 97) has a sole that's
flat for only about an inch either side of
the throat opening, with the rest of the
sole so relieved that the plane barely even
rests on it. The tiny sole lets the plane
follow the surface, cleaning off saw
marks and the like rather than cutting it
flat and true. I would lap the sole of a
scrub plane only if it really needed it,
otherwise consider the plane tuned and
ready for work.
Few planes are easier to use than
scrub planes. The very nature of the
work they do is so rough that a lot less
care is necessary when planing. I use a
scrub plane for two different techniques:
for removing mill saw marks or wood
quickly to leave a finished and somewhat
smoothed surface, or for hogging a
surface flat enough to be more easily
refined and smoothed by other bench
planes (see the photo at right). The two
techniques are different in so far as for
the former I leave parallel plane marks
with the grain, and for the latter plane
marks in any direction, as long as the
surface is nearly flat and true. Using a
scrub plane is covered in more detail in
the section on flattening stock below.
U sing Bench Planes
The flat soles of bench planes cut true
flat surfaces or, geometrically speaking,
planes. Whether it's flattening a surface,
shooting an edge straight, cutting a
consistent bevel, or cutting a straight
end-grain edge, bench planes are the
tools for the work. Some of this work
demands careful tuning, some less so.
But bear one qualification in mind: The
tuning should fit the work you expect to
do with the plane. Jack planes (#5) used
for general work are one step above scrub
planes and need only a modest amount
more tuning. On the other hand, a #5
used as a jointer for short surfaces should
be well tuned. A jointer (# 7, #8) or fore
plane (#6) used for accurate work also
needs careful tuning. It's always better to
err on the side of doing a more complete
tuning rather than the minimum, since
this makes any tool more versatile.
Chapter 4 describes tuning bench planes
in detail.
You can get by with only three or four
well-tuned bench planes, a #4, a #5, a #7
or #8, and a low-angle block plane. It's no
surprise that these are the most common
sizes available on the used tool market
(or new from any of the few remaining
cast-iron plane makers), as generations of
A scrub pl ane i s
used on the
di agonal to hog a
panel flat before
fi nal smoothi ng wi th
other bench pl anes.
The surface i s l eft
wi th pl ane marks
that l ook gouged,
and the shavi ngs
are coarse and
roughly broken.
craftsmen have found that they vary just
enough in length and heft to work well
for a wide range of bench work. You
won't use each one every day, but in the
course of a week or month you will use
them for everyhing from flattening
rough stock to thicknessing it, leveling
glued-up panels, and jointing long-grain
and end-grain edges.
FLATTENING STOCK
Hardly any board dries flat across its
width and straight along its length.
Instead, due to the very nature of wood
and sawing a log into boards, most of
those boards will warp in some way. The
three most common defects are twist,
cup, and bow (see the drawing on p. 100).
Twist is what the name suggests, a
gradual twist of the board's face down its
length. Cup is a warping across the
width of the board, and bow down its
length. Fortunately, these are just the
sort of problems bench planes were
designed to resolve.
P L A N E S F O R T R U I N G A N D S I Z I N G S T O e K 99
Bow, C u p , and Tw i st
BOW DOWN
LENGTH
Use a long
straightedge to
measure bow.
TWIST DOWN
LENGTH
Check twist by sighting
across winding sticks.
Let's say I want to flatten a board a
few feet long and 14 in. wide that has all
three of these defects. First, I saw the
board close to final dimension so I'm not
planing wood that will just be waste
,
later. The most secure way to hold the
board is clamped between dogs on a
bench (for more on holding the work, see
Chapter 5). Chances are good that it
might rock or otherwise not lie steady,
which can be remedied by tucking a few
wedges under the board at the high spots
(see the photo on the facing page).
Checking the warp with winding sticks
and a straightedge gives me a good idea
of where wood needs to come off (see
the sidebar on the facing page).
1 00 C H A P T E R S I X
,
,
,
,
,
CUP ACROSS
WIDTH
Check for cup with a
straightedge held
across the width.
There is no rule of thumb for which
plane to start with, either a scrub plane
or one of the longer bench planes tuned
with a slightly cambered iron. If the
board is quite warped, I start surfacing
by hogging off the high spots with a
scrub plane. Think of a scrub plane as
one step above a hatchet and a jack plane
as one step above that. No matter what
plane I start with, the technique is the
same: I plane on the diagonal, with the
plane at a skew. Planing diagonally end to
end cuts out the twist and cup by
working more heavily on the corners that
are high.
While flattening the surface, I find it
useful to turn the board end for end at
least once. Planing diagonally in the
opposite direction evens out a natural
tendency to pressure the plane to cut
more heavily in a certain direction or at
the beginning or ending of a stroke.
I stop occasionally and sight along the
surface for a quick check on my progress.
You can use straightedges and winding
sticks, but, to save time, it's really good
practice to train your eye to see the plane
your tools are cutting. You'll still need to
check with winding sticks for final
accuracy.
Planing across the grain at a skew is
efficient for another reason: It lessens the
tearout likely when cutting along the
grain. With the iron set for a hefty cut,
the throat wide to pass large shavings,
and the iron less than perfectly sharp (as
it will quickly become with this hard
cutting), it's easy to imagine that the
plane won't cut perfectly smoothly along
the grain. The aim is to cut a flat surface,
with some roughness to be expected,
especially if you start with a scrub plane.
The planes that follow will refine and
smooth the surface.
As the surface gets flatter, I lighten
up on the cuts. Once the bulk of the
waste is removed, it's also a good time to
resharpen or switch to a plane with a
finer throat and less cambered iron.
Sometimes a slightly rough but flat
surface is all that I need, say for the
underside of a drawer bottom. In this
case, I leave a smoother surface by
overlapping the final strokes across the
width and planing with the grain from
end to end.
For a very true panel, it's best to
finish with a long plane. With the plane
set for a light cut and slightly skewed, I
continue to plane on the diagonal, as
shown in the top photo on p. 102. The
final strokes should be down the length
of the panel to leave a surface ready for
final polishing with a well-tuned
smoothing plane and scraper. I like to
delay finish-planing the parts until just
M A K I N G A N D U S I N G WI N D I N G S T I C K S
A
pair of winding sticks is
one of those shopmade
tools that you can either lavish
time and attention on making
or grab out of the scrap pile.
I've seen them made of
boxwood with laminated
edges of holly and ebony, or of
just two pieces of plywood.
Either works well.
Traditional winding sticks
(or "winking" sticks, as they're
sometimes known) are made
from a stable wood such as
mahogany, rosewood, or teak,
about 2 ft. long, 2 in. wide,
and tapered in cross section
with a wide base. Laminating
contrasting woods to the top
edges makes it easier to read
one edge against another,
although you can simply run a
dark pencil line along the top
edge of one for contrast. More
important is that each stick
have top and bottom edges
parallel with each other and
that the sticks are not warped.
It doesn't matter if the sticks
are different heights.
The way winding sticks
work is simple enough. One
stick is laid across one end of a
surface, the other stick across
the other end. Sighting across
their top edges shows any
twist or winding (hence the
name). If the top edges are
parallel, then the surface is
"out of winding," or not
twisted. The farther they are
out of parallel, the more twist
there is. Long sticks
accentuate any winding and
make it easier to see.
Considering their simplicity
and accuracy, winding sticks
are a quick way to check the
flatness of plane soles, boards,
or glued-up panels.
Si ghti ng across the top edges of
a pair of wi ndi ng sticks reveal s
any twi st or wi ndi ng i n a roughly
flattened panel .
P L A N E S F O R T R U I N G A N D S I Z I N G S T O C K 1 0 1
A l ong joi nter i s
used to bri ng the
board to flatness,
removi ng the scrub
or jack pl ane marks
before a fi nal pol i sh
wi th a smoothi ng
pl ane.
To pl ane a board
to consistent t hi ck
ness, first scri be
around al l four
edges wi th a mark
i ng gauge, usi ng
the fl attened face
of the board as a
reference surface.
1 02 C H A P T E R S I X
before assembly and after all fitting and
joinery are completed (with the potential
for dings and other mishaps). Techniques
used for final smoothing are covered in
Chapter 8.
THICKNESSING STOCK
Once one face is flattened it becomes a
reference surface for thicknessing the
reverse face. To thickness the 14-in.
rough board that was flattened in the
previous step, set a marking gauge to the
desired thickness and, bearing against
the true face, scribe around all four edges
of the board, as shown in the bottom
photo at left. (It's easier to see the line if
all four edges are smoothed with a plane
beforehand.) By planing right up to these
reference lines the board will finish to a
consistent thickness and be as flat as the
face first trued.
The flattening technique is the same
as for the face already completed, except
that it should be easier knowing where
you need to end up. Start with a scrub
plane if you like or with a longer bench
plane. Either way, work the surface at the
diagonal and stop just shy of the reference
lines. I like to plane the lines away with a
finely set jointer, held at a slight skew
and planing down the length of the
board with overlapping strokes. A final
once-over with a smoothing plane will
take off so little wood that the thickness
should be virtually unchanged. With
two true faces and consistent thickness,
the next step is to joint parallel edges
and ends.
JOINTING SQUARE
EDGES
Only occasionally do I joint roughsawn
(as opposed to table-sawn) edges with a
plane, rather than go straight to the
jointer. In my small shop it's usually those
boards longer than about 9 ft. or the
ones too heavy or awkward to pass over
the jointer. More commonly, I use a plane
to refine edges that have already been
straightened with a jointer or table saw,
say for trimming straight parts to size or
for edge-gluing boards for wider parts.
Jointing technique is harder to master
than flattening, mostly because it takes
time to learn how to balance the plane
on an edge where it is only partially
supported-quite different from having
the entire sole resting flat on a board
when surfacing it. And if the forces on
the plane through the stroke are not even,
it's more likely that you'll cut a crown or
high point along the edge by cutting the
ends more heavily. Fortunately, there are
a few tricks that will help.
To joint short boards, I hold them in a
side vise. Longer boards can be clamped
along the front face of the bench with
one end held in the side vise and the
other supported in some way. I use a
short board clamped in the jaws of my
end vise, but a portable board jack or one
fixed to the bench works well, too (see
pp. 83-85). However you hold the board,
set the edge you are going to joint at a
comfortable height, get it as stable as you
can, and orient it so that you are cutting
with the grain.
Choose a plane that fits the work
you're doing. The longer the plane, the
easier it is to get a straight edge, but with
more weight to balance and control. For
Worki ng the surface
on the di agonal ,
pl ane just to the
gauge l i nes.
edges under a few feet long I use a #5 or
#6; any longer than that a # 7 or #8. The
better the tuning for any of these planes,
the finer shaving you can cut and the
better the jointed edge.
The key to getting good results is to
concentrate on each stroke. Initially
flattening a surface is very different in
Whi l e j oi nti ng an
edge, use your
front hand to steady
the plane, wi th
your t humb agai nst
the front knob and
your fi ngers
wrapped around the
sol e agai nst the
board face.
P L A N E S F O R T R U I N G A N D S [ Z [ N G S T O e K 1 03
1 8 T H - C E N T U RY S T O C K P R E P A R AT I O N
T
oday we take it for
granted that you can buy
materials thicknessed and
planed smooth by machine, in
whatever dimension or
quantity you desire. But the
amount of labor it once took
to work roughsawn boards to
finished dimension was
enormous. Just think of the
thousands of feet of planed
lumber in a building: for trim
and moldings inside and out,
windows, doors, floors,
wainscoting, stairs, cupboards,
and clapboards. And the only
machine the 18th-century
carpenter had was himself.
While the work took
considerable energy, the tools
and skills of the carpenter
made the work as effcient as
possible. Benches were low so
that the whole upper body
could apply force to the plane.
Holding devices were simple
a toothed stop at one end of
the bench and a large forged
holdfast. The planes were
simple, too: wooden jack or
fore planes, jointers, and
smooth planes.
Flattening and thicknessing
a rough board was a straight
forward process. First, one face
was flattened and smoothed.
Any warp or twist was planed
out with a jack or fore plane
(so named because it was used
"before")' With a wide throat,
a convex shape to the edge of
the iron, and sometimes even
a sole with the same convex
shape, the plane could cut
quickly and take coarse
shavings. A jointer, with its
long sole and square iron,
refined and trued the surface.
A smooth plane gave a final
polishing.
Once one face was flattened,
the carpenter used a jointer to
shoot one edge straight. He
then used that edge to guide a
panel gauge in marking the
opposite edge parallel and to
the board width. This second
edge was either ripped with a
saw, chopped close to the line
with a hatchet, or hogged
straight with a jack plane and
then trued with a jointer.
Often the carpenter stopped
here, with a board surfaced on
one side and cut to width. For
boards exposed on one side
only, to plane the back only
added unnecessary labor.
To cut a board of consistent
thickness, the carpenter used
a marking gauge set to the
desired thickness and, guiding
it against the flat face, scribed
a line along each edge. With
the same jack and jointer, he
cut the back to this line. In a
day a man could plane perhaps
300 surface feet.
An 1 8th-century carpenter' s bench was low, enabl i ng the carpenter to
del iver opt i mum power to the pl ane. ( From The Little Book of Early
American Crafts and Trades; courtesy Dover Publ i cati ons. )
this way-strokes can stop and start
where they will as long as wood is
coming off where needed. To joint
accurately you need to think about both
balancing the plane and pressuring it
evenly, especially at the start and end of
the stroke (see pp. 88-90). Long even
strokes give the best results.
I hold the front knob in a particular
way to give me extra control guiding the
plane. Instead of grabbing the knob with
a few fingers as for flattening, I wrap my
fingers around the side of the plane and
rest my thumb either against or around
the front knob (see the bottom photo on
p. 103). My fingers under the sole act
like a fence to steady the plane. At the
end of the stroke I can still pick up the
plane with both hands or take most of
the weight with the rear handle.
There are other things to concentrate
on that will help. Think about keeping
the plane at right angles to the face of the
board. When you become sensitive to it,
you can actually feel when the plane is
tilted a few degrees to one side or the
other. Watching the shaving will help,
1 04 C H A P T E R S I X
Turni ng the j oi nter around and pl ani ng backwards takes out any
crown at the starti ng end of the board.
To j oi nt boards for edge gl ui ng, lay them out i n order, mark the j oi nts,
and then j oi nt each edge.
too. If the iron cuts more deeply on one
side than the other, the shaving will be
more opaque along that side. The thinner
edge of the shaving might be frayed. If
the shaving is inconsistent across its
width, either the iron is out of parallel
with the sole or the plane is tilted and
cutting more heavily on one side.
With the first few jointing strokes, the
shaving will come out in pieces as the
high spots are planed off. On a really
rough edge, I set the iron quite deep and
hog away-sometimes even using a scrub
plane to start. Jointing an edge off the
jointer or table saw, I start with a light
cut to see how the grain behaves. In
either case, use the entire width of the
iron (not just the center) by shifting the
plane right or left with each stroke; it
will mean fewer sharpenings. Stop
occasionally to check that the edge is
square by holding a square against the
face of the board and across the edge.
Sighting down the length of the edge
will give a good idea of your progress,
too. One thing to watch out for is if the
edge is crowned-even the longest plane
will follow it somewhat. On the other
hand, a plane will eventually cut a
hollowed edge straight.
To straighten crowned edges, think of
it as taking off the high spots one shaving
at a time. Start the cut in from the end,
plane along, and lift off the plane before
reaching the other end. Look down the
edge and keep on cutting partial strokes
where the edge is high and eventually the
crown wi be gone or will be a lot smaller.
Sometimes it's still hard to straighten
a crown at the starting end of the cut.
Even on the longest jointer the length of
sole in front of the iron is only 8 in.
hardly enough to guide the plane straight
when the edge is gently crowned. At the
end of the stroke the entire sole is
guiding the plane straight, so it's easier to
cut away a crown there. The solution is
to plane the starting end the same way;
turn the plane around, start the cut a
plane length or so from the end, and pull
it toward you, as shown in the top photo
at left. Used this way the whole sole is
guiding the cut and cutting off the
crown. You'll be planing against the
grain, but with a light cut any tea rout
should be very fine. Repeat this a few
times, and then plane the edge along its
entire length to straighten it completely.
Jointing boards
for gluing edge to edge
Of all the edge jointing I do, more than
half of it is for fitting butt joints for edge
gluing. It has always amazed me how
often I hear of other woodworkers gluing
up edge joints right off of a machine. I've
never had the same success. Gluing two
P L A N E S F O R T R U I N G A N D S I Z I N G S T O C K 1 05
boards edge to edge jointed on even a
sharp jointer can be risky. Under a
magnifying glass the machined surface is
a pattern of fine ripples. Two such
surfaces put together will never mate
well, because they touch only along the
tops of the ripples. It's even worse when
the jointer is slightly dull-the wood
fibers are beaten down or so abraded
that they become a poor glue surface.
And, as accurate as I like to think my
jointer is, the edges it cuts are never truly
When edge-joi nt i ng two boards, check the dry joi nt with a strai ghtedge
and l ook for gaps between them.
To j oi nt boards i n pai rs, fol d the boards together, l i ne up the edges to
be j oi nted, and cl amp securely.
1 06 C H A P T E R S I X
straight. It's no wonder then that gluing
up machine-jointed edges takes a lot of
clamps and glue.
Run a jointer plane over the edges
before gluing and the story is very
different. The edge will be flat and
straight (or you can plane in a slight
hollow if you like, as explained on p. IOn
The cleanly cut fibers will give the best
glue surface there is. The joint will go
together more easily, and it will be strong
and as invisible as it can possibly be.
Better yet, such joints will stay together
long after the limited glue bond of the
machined edges has failed.
Edge-jointing boards meant to be
glued to each other is more difficult than
merely jointing an edge straight. Mating
edges must be straight and square along
their entire length. There are several
ways to joint them. One method is to
joint the two edges together as they are
held side by side in a vise. Special
shooting boards or jigs can also help. I
prefer to joint each edge singly and, if
need be, adjust it slightly to fit its mate.
I begin by laying out the sequence of
boards for the best grain match (or for
other criteria such as color) and mark
each joint. Then I joint the edges of each
butt joint in order. For the sake of clarity
the edges of each joint can be identified
as A and AI , B and BI , and so on (see the
bottom photo on p. 105). Once A is
jointed and laid aside, I put AI in the vise
and shoot it straight. Keeping AI in the
vise, I turn A upside-down onto it as if
gluing them together. I check for two
things: that there are no gaps between
the boards (particularly at the ends) and
that their faces lie in the same plane. If
there are any gaps in the joint, I take
another shaving or two from A I (still in
the vise) until the two edges mate
perfectly. To check that the faces lie in
the same plane, I hold a straightedge
across the width of both boards resting
S U R F AC I N G G L U E D - U P P A N E L S
M
aking wider panels
from edge-glued boards
is probably the most common
woodworking joint there is,
used for everything from case
sides to tabletops. Thickness
planers that can flatten such
wide panels are expensive.
The two or three planes it
takes to do the work by hand
can be bought for under
$200-and you'll have them
for a lot of other work besides.
depend on being aware of the
direction that you machined
the individual boards initially.
I always mark each surface
with an arrow, indicating the
direction it passed through
the planer or over the jointer,
and try to align all the arrows
in the glued-up panel. If I then
plane against the arrows, I get
the least tearout.
The iron needs only a
very slight camber or none at
all; I generally relieve only
the corners. Work in an over
lapping pattern along the
panel and be aware of trying to
cut to a consistent depth so
the overall thickness doesn't
change. Stop when the surface
is covered with an even
pattern of planing marks. If
it's easier, draw some random
pencil scribbles on the surface
No matter how carefully
the joints were made and
assembled, there's bound to
be slight variation between
each. Start surfacing with a
long jointer for the truest
finished surface, using the
same diagonal technique
described on p. 100 and
cutting with the grain as
much as possible. Use a light
cut to avoid tearout, or you
risk having to plane the whole
surface lower. The best results
to plane away. Use a smoothing Surface a gl ued-up panel by fl atteni ng out the transi ti ons between
plane and a very fine cut for pi eces. Pl ane on the di agonal just as with a wi de board.
the final finish.
edge to edge (see the top photo on the
facing page). If they do not lie in the same
plane, I'll apply slightly more pressure to
the plane or tip it to cut a minute bevel
to adjust the edge of AI and tip its face
into alignment. The better the dry joint
is, the easier they will go together with
glue and the stronger the joint. And so it
goes down the row of joints.
Some woodworkers like to hollow
joint the edge slightly. The theory is that
a slight hollow between the pieces will
create more pressure upon the ends as
the hollow is clamped together. The
pressure helps keep the joint together as
the end grain gains and loses moisture,
potentially cracking open the same way
the end of a board seasons and checks.
I use hollow jointing for long edge joints.
The technique requires one extra step:
I take an extra shaving or two off the
center of the board and then make one
more pass from end to end. With A and
AI edge to edge, the hollow appears as
the faintest hair of light between them.
It might sound tedious or a matter of
chance to joint edges singly, but it's
surprisingly easy when you get the feel
for it. An alternative is to shoot the edges
in pairs, as shown in the bottom photo
on the facing page. The theory is that as
long as the edge is straight, any minute
bevel planed into the edges will balance
out. This technique works best for
jointing short boards (under about 4 ftJ
and thin stock, for such things as drawer
bottoms. The dou ble thickness of the
two boards together gives that much
more support to the plane's sole. Fold
the two boards together, clamp them in
the side vise, making sure the edges are
P L A N E S F O R T R U I N G A N D S 1 Z J N G S T O e K 1 07
Shooting Boar d s
f or Ed g e J Ointing
Two straight-edged boards cl amped
i nto si de vise
Boards to be edge-joi nted
Ramped shooti ng board for short
boards or thi n stock
Stop
Use plane on side.
tight to one another, joint the edges
straight, and trial-fit them. Check for
gaps and that the faces lie in the same
plane as described previously.
Another alternative is to use some
sort of jig or shooting board. A shooting
board is a good aid for getting a feel for
jointing or for jointing really thin pieces;
otherwise, I find that it's more trouble
setting everything up than it's worth.
1 08 C H A P T E R S I X
Plane at slight skew.
Temporary stop to
support stock
The simplest setup is to clamp two
boards together as in the method
described previously, but slightly above
and sandwiched between another pair of
shooting boards with true edges. Plane
down until the plane just starts to ride
on the edges of the shooting boards and
stop before cutting into them. The
drawing above shows this setup and
another shooting board useful for
shooting the edges of small, thin pieces.
JOINTING BEVELED
EDGES
There is no doubt that cutting a lot of
boards to a consistent bevel is faster on a
table saw or jointer than with a plane.
But for one or two bevels, especially ones
cut on tapered pieces, it's easier to pick
up a plane than make a jig for holding
the work safely on a machine. And when
it comes to adjusting bevels, say for
coopered work, a plane has no equal.
A jointer gauge is a useful aid in
learning to guide and balance a plane
upon an edge, for shooting both straight
and beveled edges. I usually don't have
much time for jigs and gimmicks, but
this is one tool that is invaluable.
Essentially it's a guide that clamps to
either side of a Bailey-pattern bench
plane with an adjustable fence against
the sole (see the top photo on the facing
page). With the fence held against the
face of the board the plane is supported
to cut any bevel from 30 to 90 . It's not
a foolproof jig and it takes some skill to
use, but it's the best way I know to cut
bevels consistently with a plane. Mine
was made by E. C. Stearns Company and
dates from about the turn of the century.
There are fancier versions; Stanley made
a jointer gauge that was nickel-plated,
with a rosewood knob on the clamp to
the plane to allow more control. Although
I've never seen new ones for sale, jointer
gauges can be found at tool sales. It's also
easy enough to fashion a wooden version
to cut a specific bevel (see the bottom left
photo on the facing page).
I use two beveling techniques: cutting
a specific bevel on an edge or refining or
adjusting a bevel cut on a machine. For
either technique, a jointer gauge helps
you work easily and with more accuracy,
but it's not essential. To cut a bevel
without one, mark out the bevel angle on
the end grain at both ends to give you
reference lines to plane to. Use your
forward hand much like a jointer gauge
Stanley and others
made joi nter
gauges, adjustabl e
over a wi de arc of
bevel angl es, that
clamp on the si des
of #4 and l arger
bench pl anes for
shooti ng accurate
and consi stent
bevels.
A beveled block of wood cl amped to a bench pl ane serves as a
si mpl e joi nter gauge.
You can j oi nt a bevel freehand by usi ng your outstretched hand to
steady and ori ent the pl ane.
to steady the plane on the bevel (see the
bottom right photo above). To use a
jointer gauge, set the fence with a bevel
gauge to the desired angle and make sure
the fence is tight to the work. Just as
with edge jointing, it's very important to
think about each stroke, feel the position
of the plane, and watch the shavings to
see where the plane is actually cutting.
Refining a bevel means planing it
straight and true, free of machine marks,
and ready for gluing or other joinery. It's
awkward only because the plane is tipped
at an angle and it's harder to balance (a
jointer gauge helps); otherwise, the
strokes are the same as if shooting the
edge square. It's helpful to set a bevel
gauge to the angle and check often along
the edge. Where the bevel is low I'll make
a pencil line, so I can cut more heavily on
the opposite edge (saving the line) and
correct the bevel. An alternative is to
pressure the plane more heavily to cut the
high side or to adjust the lateral align
ment of the iron out of parallel. Either
way, I watch the shavings and finish with
a continuous pass from end to end.
P L A N E S F O R T R U I N G A N D S I Z I N G S T O e K 1 09
I nspi red by low
angl e British miter
pl anes, thi s rare
Stanl ey #9 cabi net
maker' s bl ock pl ane
has a bal l -tail handle
and a " hot dog" for
hol di ng the plane
when i t' s used on its
si de for shoot i ng
miters or pl ani ng
end grai n.
Planes
for Dimensioning
End Grain
When it comes to dimensioning end
grain, the techniques are basically the
same as for planing long grain. Even the
same bench planes can be used. What is
different is that end-grain fibers are a
lot more tenacious than long grain.
The physics of block planes, with their
low-pitched irons, can be a definite
advantage in cutting end grain easily.
1 1 0 C H A P T E R S I X
The first block plane that Stanley
offered (a #9 in 1 870) was squarish and
heavy, a little longer than a smoothing
plane, and with an iron bedded bevel up
at 200 (see the photo above). It was the
most expensive bench plane Stanley
offered, to be "used by Piano Forte
Makers, Cabinet Makers and kindred
trades, where an extra-fine Tool is
required in finishing hardwoods."
Stanley didn't advertise it to cut end
grain specifically, although the plane's
mass and low-pitched iron helped. The
design came from earlier British miter
planes made from a block of hard
wearing wood (see the bottom photo
on p. 35) or of the metal-and-wood
construction typical of these and other
high-quality British planes.
Within a few years Stanley came out
with a new line of block planes for
general-purpose work and some for
special tasks. The name "block" plane, so
the story goes, comes from the plane's
use to resurface the end-grain tops of
butcher blocks. Stanley offered the #64
specifically for surfacing butcher blocks.
It was a low-angle plane with a toothed
cutter for initial leveling and a straight
cutter for finishing the surface (see the
bottom photo on p. 1 17). For the cabinet
maker, Stanley made a similar plane, a
low-angle jack (#62). It was really just an
oversized block plane, much longer and
with larger handles to allow a good grip
while working stubborn end grain.
It wasn't very long before Stanley and
other manufacturers were offering a
wide range of block planes for use
throughout the woodworking trades.
The variety was huge-with adjustable
throats, very low bed angles, skewed
irons, ball-tail handles, fancy lever caps,
double ends (one end was for bullnose
work), and different sizes and qualities.
Today there are maybe h new block
planes available, all nearly the same as
the basic planes offered 100 years ago.
TUNING BLOCK PLANES
Three things set block planes apart from
other bench planes: They have a single
iron without a cap iron, the iron is
bedded at a low pitch, and the bevel of
the iron faces upward. Each characteristic
can improve the dynamics of cutting end
grain, which is quite different from
planing long grain. Long-grain cutting
curls up a shaving, cut (and split) from
the surface along the plane of the wood's
natural weakness. The steeper the angle
the iron makes with the surface, the
more abruptly the shaving is curled and
generally the smoother the surface the
plane cuts. Cap irons stiffen the iron and
accentuate this curling action. End grain,
by contrast, is best cut with an iron more
like a knife than with the wedging cut of
a higher pitched iron. The best end-grain
cut slices the end of each resilient fiber.
The lower the pitch of the iron and
the finer its bevel, the better it can cut
the fibers. Ideally zero pitch, cutting like
a chisel, would be best. But to make a
plane like this would be impossible; at
even a low pitch the thinly tapered bed
is fragile. As it is, end grain is tough to
cut and wears on the sole more than
long grain.
The lowest practical bed angle turns
out to be about 1 2 . Cutting with the
iron bevel up, the effective pitch (the
pitch of the actual cutting edge) is the
total of the bed angle and bevel angle,
something about 32 (see the drawing
on p. 49). Most block planes have a bed
angle closer to 20, which, interestingly,
makes their effective pitch not much
different from that of a jack or smooth
plane. It might look as though the iron is
cutting at a lot lower angle, but the
physics is actually quite similar. Herein
lies the crux of the tuning question:
Should you tune the plane to work like a
small smoothing plane-which it will do
very well-or take advantage of its low
bed angle and potential to shave end
Bl ock planes once came i n a vari ety of
qual i ti es and sizes from many manufacturers.
Shown here (from top) are pl anes from
Metal l i c Plane Co. of Auburn, New York,
c. 1 873; O. R. Chapl i n (with a corrugated sale
and adjustabl e throat), 1 888; Foss ( patent #3
wi th adjustabl e throat), c. 1 878; and Davis
Level Co. of Spri ngfi el d, Massachusetts, 1 892.
P L A N E S F O R T R U I N G A N D S I Z I N G S T O C K 1 1 1
A bl ock pl ane di sassembl ed shows its si ngl e i ron, adjuster, cam-l ocki ng lever cap, adjustabl e
toe pi ece and the knob that secures i t, and low bed angl e. Too Iow a bed angl e i s fragi l e, as
shown by the skewed bl ock pl ane i n the background whose bed has cracked away.
grain? But, before we get into this issue,
there are other characteristics of the
plane worth understanding.
Having a low bed angle means the
iron has to be used bevel up; if it were
down, the bevel would have to be smaller
than the bed angle and impossibly fine
and fragile. But this also means there is
no way to have an effective cap iron. For a
few reasons it really isn't needed anyway.
The low bedding angle puts the cutting
forces more in line with the iron (the
knife vs. the wedge again), and as a result
the iron is able to resist them without a
1 1 2 C H A P T E R S I X
cap iron. The lever cap (or screw cap)
that secures the iron helps to stabilize it,
too. Block planes can cut well without a
cap iron for one more reason: There is
little need to curl the shavings. End-grain
shavings are so weak that they break
apart easily. If you do cut a long end
grain shaving, you'll know your plane is
properly tuned.
The basic tuning is the same as for any
plane, described in Chapter 4. Take extra
care lapping the sole, because this is a
plane you'll want to get accurate work
from, and the sole is small anyway.
Smoothly bevel all around the edges of
the sole so there is no chance of any
burrs or sharp edges marring your work.
Then turn your attention to the lever
cap. This part of the plane is doing a few
jobs-securing the iron, stiffening it, and
supporting your palm at the rear of the
plane. To do the first two jobs it needs to
lie against the iron completely, just as a
cap iron would. Sand off any paint on
the underside where it mates with the
iron, and then lap it on a coarse stone by
holding the lever cap slightly below the
level of the stone along one side (see the
photo on p. 73). Polish the top edge so
the shavings will pass smoothly from
the throat. Anything more you do with
the lever cap won't really afect the
plane's performance, although you
might want to smooth the area where
your palm rests.
Next in importance is a smooth and
consistent bed for the iron. If you have
just bought a new Stanley or a Record
#912 or #6012, classic block planes that
are nearly unchanged from over a
century ago, the bed will probably need
some work. First, remove the lever-cap
retainer screw and the adjustable toe
piece if there is one, so neither is in the
way. With a small flat file, file the bed
flat right to the bottom of the sole (see
the photo at left on p. 59). Applying a
thin coating of wax to the bed helps the
iron adjust smoothly.
The way the iron is ground and honed
will really determine how your plane
performs. Ground at a normal 250 bevel,
with a bedding angle of 200 , the plane
will work like a small smoothing plane.
Hone a microbevel of another 50 (a 500
cutting angle) and it will work even
better for difficult grain. A 100 micro
bevel (a 550 cutting angle) will give you
about the best performance you can
expect with long grain, but you're way
off the mark to plane end grain easily.
A DJ U S TA B L E T H R OAT S
T
he width of the throat has
a major effect on the way
a plane cuts, yet adjusting the
throat opening is not always
quick and easy. On most
bench planes you first have to
remove the iron and lever cap,
and then loosen the frog and
slide it forward or backward.
#4 in size), the #9 miter plane,
and a few other specialty
planes. A few modern wooden
planes have the same feature.
For real ease and versatility
in throat adjustment, nothing
beats the few planes manu
factured with a separate toe
piece. By loosening a screw or
the front knob, a piece of the
sole (or the entire sole) ahead
of the iron can be moved
forward or backward. In a
matter of seconds, the throat
can be widened from as thin
as a hair to as coarse as a jack
plane. This is the design
Stanley and others used for a
modest number of planes:
block planes, a low-angle jack,
a bench rabbet (similar to the
Given the benefits, you
might wonder why more
planes are not made with an
easily adjustable throat. One
reason is that milling the toe
piece, the recess for it, and the
front knob that secures it
takes careful manufacture,
adding to the cost. Another
reason this design doesn't suit
all planes is that it makes them
more fragile. No longer is the
plane one solid casting, but a
milled-down main casting and
a thin attached toe piece. And,
finally, not all planes need that
much range of adjustment or
need to be adjusted all that
often. They are tuned for
certain work and are used for
just that.
The adjustabl e toe pi ece i s secured to the pl ane body
with a knurl ed knob.
To cut end grain you want the lowest
cutting angle. Choose a plane with a bed
angle of 1 2 , hone the bevel to 20 , and
then hone a back bevel of 5 . The
effective cutting angle is 3r-quite a bit
lower than a bench plane. The overall
bevel angle is 25 and sturdy enough to
plane hardwood end grain. But you
could get a little more from the plane if
you regularly planed only softwoods. A
1 5 bevel and 5 back bevel yield a
cutting angle of only 2r. Work this
plane on the skew and you'll be amazed
at how easily it cuts and how smooth a
surface it leaves.
DIMENSIONING
END GRAIN
If the biggest challenge with block planes
is tuning them, actually using them is
easy. Most fit you r hand so comforta bly
and can do such a variety of small
planing jobs that a block plane will
quickly become the first plane you reach
for. I have three block planes at the ready
on my bench at all times. Two are about
a hundred years old, with adjustable
throats and castings beautifully designed
so they are comfortable in my hand for
long periods of planing. One is a Stanley
#9 Y2, the other a Sargent # 1 317
(basically the same plane only a little
longer) with a ball-tail handle that makes
the plane more comfortable to use two
handed (see the photo on p. 1 14). The
third plane is only a few years old; it's a
Lie-Nielsen low-angle bronze plane
based on an old Stanley design, which I
love for its compact beauty and the way
it can handle the work of a plane many
times its size and weight.
It would be difficult to list everything
these planes can do. Certainly they
square or bevel end-grain edges, or any
P L A N E S F O R T R U I N G A N D S I Z I N G S T O C K 1 1 3
Four of the author' s
favorite bl ock pl anes
i ncl ude (from top) a
l ow-angle Stanl ey
#60%, a Sargent
#1 31 7 wi th a bal l -tai l
handl e for a com
fortabl e two-handed
gri p, a Stanl ey #9%,
and a Lie-Ni el sen
bronze low-angl e
bl ock pl ane.
edge for that matter; cut miters,
chamfers, and bevels across or with the
grain; and true up joints such as rabbets
or the face of a tenon. The Stanley I have
tuned to work more like a small
smoothing plane, so I use it to level
transitions at joints (for example,
between stiles and rails on a door), to fair
curves, and to do the job wherever a
small plane seems to fit the work best.
1 1 4 C H A P T E R S I X
Squaring or trimming end-grain edges
is the work block planes do much of the
time. This might be in fitting a piece,
taking a shaving or two off its length, or
truing the edges of a glued-up panel such
as a small tabletop. The technique is easy
to learn, but as with any plane, it takes
sensitivity to the way the plane cuts. You
want a sharp iron for any planing task,
but especially for planing end grain. Use
a light cut, too; end grain is tough stuff.
Clamp end-grain edges upright in a
side or end vise to work on them most
comfortably. Keep the piece low in the
vise so that it's as well supported as
possible; end-grain planing takes a fair bit
of force. Large end-grain surfaces are
easier to plane, only because there is
more to rest the sale on. To plane small
surfaces like the end of a table leg, I often
just lay the item flat on my bench with
the end projecting beyond the edge. I can
then comfortably look down on the work
as I plane, and turn the leg to work from
all four sides.
One way to pl ane end grai n is with the workpi ece securel y cl amped i n
a vise, your rear pal m around the pl ane suppl yi ng t he force and t he
control , and your fi ngers i n front stabi l i zi ng the cut.
Cl amp a scrap bl ock to the workpi ece to prevent the end-grai n fi bers
from spl i tti ng out.
You can hold block planes with one or
two hands. Grasping the plane one
handed, I rest my palm against the lever
cap and wrap my fingers around the
sides for a firm grip. Holding a block
plane two-handed, I have the palm of one
hand against the round lever cap and
grab the toe with the thumb and index
finger of my other hand (see the photo at
left above). My free fingers on my front
hand help guide the cut and stabilize the
plane in the same way they do when
jointing a long-grain edge. The ball-tail
handle on the Sargent makes holding it
two-handed even more comfortable and
secure. With any block plane the control
and force come mostly from the rear
hand, although I steer with the front
hand, too. Both are keeping the plane
firmly engaged with the cut. More so
than with long-grain cuts, where the
curling shaving holds the edge of the iron
in the cut, end-grain cuts rely on firm
and consistent pressure on the plane.
It's important not to overshoot the
edge as you plane, because the end grain
will split away quite easily. One strategy
to prevent splitting is to clamp a waste
block to the work to support the edge,
as shown in the photo at right above.
When I'm working quickly, I usually
don't want to take the time to go
through all this, so instead I chamfer the
edges and plane with a light cut. This
works fine on things like tenons, which
get a small chamfer anyway, but it isn't
always a detail I want. Another tactic is
to plane in from each edge, skew the
plane heavily, and go easily. With a light
cut at a skew I can often cut very close to
the edge.
A shooting board is a particularly
useful aid for truing the ends of parts. It
not only helps you cut a perfectly square
edge (or a beveled edge if you want), but
it also holds the work and supports the
P L A N E S F O R T R U I N G A N D S I Z I N G S T O C K 1 1 5
Sho oting B oar d
f o r End G r ain
Use plane on side.
A bench hook works
as a qui ck shooti ng
board. The Stanley
#9 was desi gned for
use as a shooti ng
pl ane, wi th si des
accurately mi l l ed
square wi th the sol e.
1 1 6 C H A P T E R S I X
Stop can be shaped to fit
molded edge.
end-grain fibers. The drawing at left
shows a simple ramped design for
planing square ends; another design for
planing beveled ends is included in
Chapter 7 (see the drawing on p. 143).
The photo below shows a bench hook
that works as a shooting board. Any of
these ideas can be customized to fit a
particular need, such as with a molded
stop to fit the molded profile on a door
stile. The technique is straightforward
hold the work firmly and guide the
plane along the fence. Block planes work
fine for this work, but they are small
and harder to hold lying on their side.
For long edges I prefer to use an old #9,
a #4, or a #5.
I f I'm planing a long end-grain edge,
on a tabletop, for example, I almost
always use a #4 or #5 (see the top photo
at right). The longer sole gives me the
same advantages on end grain as it does
when shooting long-grain edges-ease of
cutting and greater accuracy. But the
main reason I use a larger plane is for the
handles that give me a good grip. It's less
tiring using both hands to deliver the
necessary force to the plane, especially
when both have large handles to bear
against. The 45 pitch of the iron is
not a problem; in fact, I can cut more
continuously and smoothly with a
heavier bench plane than with a block
plane just because I can hold and push it
better. At that pitch the iron scrapes
somewhat as it cuts, so it dulls more
quickly, but it's still worth it.
The alternative is to use a low-angle
jack plane, a Stanley #62 (similar to the
#64 in the photo below), or Lie-Nielsen's
version, which is basically the same
plane. An original #62 is fairly rare and
sells for at least a few hundred dollars.
Shooti ng a l ong end-grain edge with a #5 or l onger bench pl ane
works wel l . A #5 cuts a true edge and i s easi er to hol d and use than a
smal l er bl ock pl ane.
The Stanl ey #64
low-angl e jack pl ane
shown at l eft was
desi gned for trui ng
butcher bl ocks. The
#62, a si mi l ar pl ane
for furni ture makers,
is sl i ghtl y shorter
wi th an adjustable
throat and rose
wood handl es.
P L A N E S F O R T R U I N G A N D S I Z I N G S T O C K 1 1 7
Three uni que pl anes for trui ng surfaces: (foreground) a Stanl ey #95 for tri mmi ng end grai n,
with its 90 fence cast i nto t he body; ( l eft) a Mi l l ers Fal l s skew bl ock pl ane ( nearly i denti cal t o a
Stanley # 1 40), with one whol e si de removable for rabbeti ng work; and ( ri ght) a Sargent rabbet
block pl ane #507 usef ul for rabbet work i n ti ght places.
1 1 8 C H A P T E R S I X
I owned and used one for a few years
and finally gave up on it. It worked no
better than my #5, despite its low-angle
physics and the comfortable handles. I
suspect the #62 is uncommon because it
was double the cost of smaller block
planes that readily served the needs of
most craftsmen.
SPECIALTY
END- GRAIN PLANES
I'll admit it, I have a fascination for odd
ball planes. A number were designed
specifically for cutting end grain. Some
I use once in a while for work I know
they do well. Sometimes I pick one up
just for the experience, to learn the range
of what it can do. Few planes came with
instruction manuals-certainly none of
these did-and it's not always obvious
how and where they should be used.
But what is certain is that they represent
part of the incredible variety of planes
once available, the fruit of some fertile
minds. Others must think there is value
to these planes, because a few of the old
patterns have reappeared in recent years,
cast in bronze, with thick irons and
smooth adjusters.
One of these planes is the Stanley
#95. It's a block plane with a skewed iron
and a 90 fence cast as part of the plane
body (see the photo on the facing page).
The low angle of the iron makes it handy
for cutting end grain, and in fact the
original purpose was for carpenters
trimming the ends of boards. The fence
holds the plane square to the cut, so it's a
snap to get square ends. The original
Stanley version has two holes in the body
to attach a beveled wooden fence with
screws, to guide the plane in cutting end
grain bevels. It's a little like a shooting
board and plane rolled into one.
Another curious plane is a low-angle
skewed rabbet, the Stanley # ] 40. The
design is like that of any other low-angle
block plane, except for two important
differences: The iron is strongly skewed,
and one whole side is removable so the
plane can be used for rabbeting. A new
model has an adjustable fence as well. In
theory, this should be an incredible tool,
but mine has always fallen well short of
expectations. The throat is very wide, so
it cuts poorly. This is less of a problem
with end grain, but a big problem when
I happen to want to plane long grain.
For cutting rabbets, I prefer the heft and
precision of a shoulder rabbet instead.
Maybe I just haven't found the best work
for this plane yet.
Sargent was one of Stanley's
competitors who made some unique
and very fine planes. Long before I knew
who Sargent was, or knew much about
planes for that matter, I was given a
Sargent rabbet block plane by an old
man who had built water-powered mills
and all types of heavy wooden buildings
throughout Vermont. This was one of
his favorite planes. What makes it so
handy is that the iron extends flush with
both sides of the plane. I use it one
handed, to clean up wide rabbets or to
work in tight places, and think of my oid
friend every time.
All of my bench planes have their own
stories. Parts of some of them I know
about the Sargent inherited from my
grandfather or about the new Record #5
discovered at a barn sale for $3. The rest
are old enough to have had a few lives
and the dings and scratches to prove it.
Who knows how many miles of edges
they've planed or thousands of board
feet they've surfaced. What I do know is
that there's always going to be a place for
them in any shop; a well-tuned plane is
too handy to be easily replaced by any
machine. They'll be just as valuable to
my children as they have been to me.
Meanwhile, I'm adding to their stories
every day.
P L A N E S F O R T R U I N G A N D S I Z I N G S T O C K 1 1 9
PLANES F OR J OINERY
Joiner, is an art manual, whereby several pieces of wood are so fitted and
join'd together by straight-line, squares, miters or any bevel, that they shall
seem one entire piece.
-Joseph Moxon, Mechanick Exercises C3rd. edJ, 1703
Good joinery i s basic to good work
work that will survive the wear and tear
of many years, and the stresses of wood
movement brought on by swings in
temperature and climate. I trust
traditional joints, mortise and tenons,
dovetails, rabbets, and dadoes that have
proved their strength over the centuries.
While it would be nice to cut them as
they were cut traditionally with chisel,
saw, and plane, today machines are more
likely to do most of the work. Yet when
you have only a few joints to cut, planes
can be an efficient alternative.
When it comes to fitting joints
precisely, no tools are more useful than
planes. Although I rarely cut a joint with
just a plane, I use many planes in fitting
joints, which allows me a flexibility
impossible with machines alone. No
longer must I design the perfect router
jig or table-saw setup to cut a complex
joint; instead, I can rough it out with
either machine and more quickly get to
where I enjoy being-working quietly
with hand tools. With a plane, I can
adjust the joint one shaving at a time,
make fewer mistakes, and do the best
work I'm able.
One of the most beauti ful j oi nt-cutti ng pl anes, a center-wheel plow
plane by Ohio Tool Company of solid boxwood wi th ivory tips, is used
for pl owi ng grooves of various wi dths. Turni ng the l arge brass center
wheel posi ti ons the fence.
Once you learn the skills and gain the
confidence, fitting joints is easy, fast, and
accurately done with planes. In an age
when every joint was cut by hand, the
sensitivity that generations of craftsmen
had for their tools slowly improved
them. The tools we have inherited are
every bit as energy- and time-eficient in
a shop today. Not only are planes the best
tools for cutting some joints and fitting
many, but they will encourage you to
work in ways or use details diffcult or
nearly impossible to create with
machines. And if that isn't enough,
you'll get a lot more satisfaction besides.
1 2 1
F u r ni tur e J oints
Rabbet
Dado
Stopped
dado
Case
mi ter
Planes
for Cutting Joints
No matter how complicated a joint
seems, it can be reduced to a few basic
elements, such as rabbets, dadoes,
grooves, and miters. A rabbet is a step cut
into the side of a board, cut either with
the grain or across the grain. A dado is a
groove of any width cut across the grain;
with the grain it's called a groove. A
miter is a joint between two angled
edges. Usually the sides of these joints
are at right angles to one another, but not
always. In the case of a joint like a sliding
dovetail, the sides are angled toward one
another. Rabbets and dadoes can be
tapered as well. It's easy to imagine that
there are nearly unlimited variations in
the ways these basic elements can be cut
1 22 C H A P T E R S E V E N
Matched boards or

or combined to create joints from the

simple to the complex. It's no wonder
then that there are numerous planes to
help cut them.
As Moxon states, joints are a way of
joining parts together to make a whole.
It's not quite so simple. As wood slowly
gains and loses moisture seasonally, it
expands and contracts as if it were still a
living material. Any joints that unite the
parts must be flexible enough to allow
this movement; otherwise, the joint will
eventually fail or something will crack
open. Rabbets, dadoes, and grooves are
three of the most basic joints that allow
parts to move yet still stay joined and
supporting one another. Miters can be
used to strengthen or conceal a joint.
There are at least a few steps to
cutting any of these joints and planes
for each step. First, the parts are
dimensioned and trued, which is the
work of bench planes. Once the joint is
designed and laid out, it's cut by
machine, hand tools, or both. Of the
many different planes that help with this
work, some more easily cut the actual
joint, others adjust it. And once the joint
is assembled and glued, any minor
differences at the transitions can be
smoothed with another set of planes or
scrapers. The first section of this chapter
discusses those planes that cut joints
most easily, the second those designed to
refine and fit them.
RABBET PLANES
Rabbet planes are among the most basic
joint-cutting planes. They all share one
distinct characteristic: The iron extends
flush with the sides of the plane body
(see the photo on the facing page).
Sometimes the iron is "rabbet-mouthed"
on only one side, although it's more
usual for it to be flush with the body on
both sides. The full-width iron allows
the plane to cut right up into the corner
of the rabbet. If the iron were not flush
with the side of the plane-for example,
if you tried to cut a rabbet with a bench
plane-it would cut only a shaving or two
before the sole to either side of the iron
contacted the wood and stopped the cut.
Some rabbet planes have another
characteristic that they share with their
cousins the dado planes: a nicker or
small knife-like cutter flush with the side
of the plane (see the photo on p. 1 24). Its
main purpose is to score the end grain
ahead of the iron, for cutting sharp
rabbets across the grain. Without the
nicker the iron would tear the fibers,
unless it was very sharp and the cut was
light. A sharp nicker also helps to guide
the plane and keep it engaged with the
cut. It's one more idea that originated in
an age of hand tools when craftsmen
needed to sink a sharp, square rabbet as
quickly and efficiently as possible.
Another common characteristic of
rabbet planes is a skewed iron. As
discussed in earlier chapters, skewing the
plane improves the cut with any plane.
In a rabbet plane confined to cutting
along a shoulder where the plane cannot
be skewed, skewing the iron gives the
same result. There are additional benefits
besides. As long as the plane is cutting
with the leading edge of the iron against
the shoulder of the rabbet, the sideways
pressure on the skewed iron helps keep
the plane tight into the corner. And by
slicing into the cut gradually, a skewed
iron is easier to get started.
A skewed iron not only improves the
cut but also makes ejecting the shavings
easier. With the leading edge of the iron
cutting along the shoulder, the shavings
curl out of the way. In some rabbet
planes (see the bottom photo on p. 125)
The iron of a rabbet
plane extends fl ush
wi th the si de, formi ng
a " rabbet mouth" for
worki ng r i ght up to
the shoul der of a
rabbet. Note the
unusual adjustabl e
t hroat on the pl ane
at center.
the shavings are ejected up through
the throat and out the top in what is
known as a bench throat (because it's
common to bench planes). For other
rabbet planes without a bench throat,
the shavings curled up along either side
of the iron spill out the sides of the
plane. Sometimes a bevel on the end of
the wedge helps direct the shavings. For
shallow rabbets ejecting the shavings is
usually no problem, but for deeper
rabbets the shavings can clog up or get
P L A N E S F O R J O I N E R Y 1 23
Ni ckers score the fi bers on cross grai n ahead of the i ron for a cl ean sharp rabbet. Shown here
are a Stanl ey "wheel " type ni cker with i ndivi dual spurs and a wooden rabbet wi th a knife-l ike
nicker dovetai l ed i nto the si de of the pl ane. The notch filed i nto the si de of the ni cker i s used to
adjust i ts depth.
lodged along the side of the plane. The
solution is both functional and elegant;
one side of the throat is opened up in a
snail-shaped escapement that widens
toward the outside, encouraging the
shavings to move that way (see the
photo above).
For the hundreds of years before cast
iron became the material of choice for
planes, most rabbet planes were made of
wood and had this distinctive throat
shape. Less common, and far more
expensive, were British rabbet (or
"rebate" in Britain) planes made by the
same makers and with the same methods
1 24 C H A P T E R S E V E N
as their better-known smoothing planes:
Spiers, Mathiesons, and Norrises of
joined steel soles and sides, with exotic
wood filling the space within.
The average carpenter or cabinetmaker
of the 18th and early 19th century had
only a few styles and sizes of wooden
rabbets to choose from. They were used
for a wide range of tasks, everything
from cutting rabbets to join boards for
wainscoting, wall sheathing, and cabinet
backs, to fitting or cutting tenons and
cutting rabbets in door and window
frames for securing glass or wooden
panels. As might be expected with such a
useful plane, each trade adapted the
rabbet to its particular needs. The
housewright and bridge builder had
heavy rabbet planes for fitting large
timbers and trimming tenons and
shoulders; the coachmaker had a
different set of smaller curved rabbets
that suited his work cutting rabbets for
curved doors, windows, and panels (see
the photos on p. 217).
As machines became more and more
sophisticated and capable of many of the
tasks formerly done by hand, the uses for
rabbet planes changed, too. A table saw
or shaper could cut any size rabbet far
more rapidly and accurately than any
plane. It was a familiar story for many
planes, yet rabbet planes were too useful
to disappear entirely. Instead, wooden
versions were replaced by cast iron, in
similar patterns and styles and, typical of
the inventive spirit of the last half of the
1 9th century, in many more designs
besides. If machines were doing the bulk
of the hard work, planes were still
necessary to refine the work. Eventually,
Stanley and other manufacturers offered
wide and narrow rabbets, bullnose
rabbets with the iron very close to the
toe of the plane for working in tight
places, low-angle and bench rabbets,
rabbet planes with single irons bevel up
and others with double irons, heavy
shoulder rabbets, and specialty rabbet
planes for coachmakers and others.
The very nature of cast iron lends
itself to a variety of rabbet-plane designs
that are difficult to make in wood. The
design of the rabbet mouth means that
at least one if not both sides of the plane
and sole are partially cut away. What
remains of the plane body has to be
strong enough to support the sole ahead
of the iron. Cutting away part of the sole,
sides, and bed for the iron in a wooden
plane can weaken it and make it more
prone to warping out of true. Cast-iron
rabbet planes could be light yet still
stable and strong, although generally
these planes are more fragile than similar
bench planes. And because the material
could be cast and worked so easily, a lot
of new designs were tried that would
have been impossible in wood (see the
photo at right).
It's an understatement to say that
there was once an enormous variety of
rabbet planes available. Although there
are subtle differences between each, they
are similar enough to be discussed in two
broad groups: those designed to cut a
rabbet, and those better suited to fine
tuning rabbets and other joints.
Shoulder rabbet planes-heavy, very fine
mouthed, and low angle-represent this
second group and are discussed later in
this chapter along with other planes that
adjust joints.
The use of cast
i ron al l owed rabbet
pl ane desi gns t hat
woul d have been
di ffi cul t or i mpos
si bl e to make with
wood al one. One
such desi gn i s thi s
extremel y rare
Stanl ey # 1 96, for
cutti ng a rabbet
al ong a curved edge.
The first group designed to cut
rabbets includes bench planes with
rabbet mouths, common wooden and
metal rabbets, and fillisters-rabbet
planes fitted with fences, depth stops,
and nickers. Stanley designs such as # 10,
# 1OV2, # 1OV4, #78, and #289 fall within
this group (as do combination planes like
the #45, #55, #46, and # 141 dealt with
in Chapter 10). Within this broad group
of rabbet planes there are unique
American styles and planes offered by
one manufacturer that are different
from another. For example, in 1872, at
the height and glory of wooden planes,
Bench-mouthed rabbet pl anes were
desi gned for cutti ng wide rabbets. The rare,
earl y Leonard Bai l ey's Victor #1 1 % (fore
ground) has a fence and depth stop (secured
wi th screw eyes); the equal l y scarce Stanley
# 1 0% has t i l t i ng handl es (to avoi d ski nni ng
your knuckl es i n ti ght spots) and two ni ckers.
P L A N E S F O R J 0 1 N E R Y 1 25
Common cast-i ron
rabbet pl anes
i ncl ude the #289
and #78 fi l i i sters
(foreground), with
depth stops, ni ckers,
and fences, and
the #10% and # 1 0
bench rabbet
pl anes for heavi er
rabbet i ng work.
Greenfield Tool Company, one of many
wooden plane manufacturers, offered
nearly 100 sizes and types of rabbet
planes and 38 different models of
fillisters, some with screw arms, some
with wedged arms, and one made of
ebony with ivory trim (and for 17 times
the price of a simple fillister).
1 26 C H A P T E R S E V E N
Tuning rabbet planes
There are enough subtleties between
rabbet-cutting planes that no general
explanation of tuning can adequately
cover them all. Some of the more
sophisticated planes clearly need special
tuning attention. Nevertheless, once you
understand the concept of tuning any
plane, and in this case a rabbet iron and
mouth, you'll know the basics for getting
any rabbet plane working well.
The key to tuning a rabbet plane is
to adjust the iron so that it is parallel
with the sole and just barely proud of the
side (see the photo at left on the facing
page). Fine-tuning the iron is one of
those things that's easier said than done.
Experiment with different settings to see
how far the iron should project to cut
well. To align the iron parallel with the
sole, tip it laterally to one side or the
other. Most irons can't be tilted much,
but there should be a small range of
motion. Check that the corner of the
cutting edge still projects beyond the
side; the rest of the iron should be back
behind the line of the side so that it
won't drag on the shoulder of the rabbet.
Most irons have a shape that makes this
easy; they narrow down in width about
1 in. or less from the cutting edge. Usually
the iron is also slightly wider than the
width of the sole, so that it's possible to
cut a rabbet the full width of the plane.
If by tilting the iron you still can't get
it parallel with the sole (and proud of the
side), the only remedy is to grind and
hone the edge. I do this mostly by eye,
grinding a little and checking with the
iron back in place. If it's really off (as
might be the case with a flea-market
plane I' m tuning for the first time), it
might take a few tries. The alternative is
to paint the back of the iron with layout
dye and scribe a fine line with a scratch
awl using the throat as a guide, and then
grind to this line. The cutting edge
should be straight across. Once the iron
is tuned, careful honing should keep
everything in alignment. I always check
before removing the iron for sharpening
to see if working a little more heavily on
one side or the other might improve it.
Skewed irons require an additional
tuning step: The back of the iron along
the shoulder side has to be beveled at
least as much as the skew angle and
preferably more (see photo at right
below). If the iron isn't beveled, the
shoulder corner of the edge can't project
beyond the side without the back of the
iron projecting even further. Actually,
beveling the iron can work to your
advantage. I bevel the side of the iron
slightly more than necessary and hone it
sharp, so that if I choose, it will scrape
the face of the shoulder ever so slightly as
the cutting edge sinks the rabbet.
The nicker should be sharpened along
with the iron. Nickers are of two types,
either an actual knife-like iron dovetailed
and wedged i nto the side of the plane or,
in the case of Stanley planes, a small
wheel with one, two, or three i ndividual
spurs (see the photo on p. 1 24). The
wheel is set into the side of the plane and
can be loosened and rotated to expose a
spur. The beauty of this design is that
one spur can be reserved for finish work,
another for roughing out, or no spur
used at all. The outside of the nicker or
spur should be aligned with the cutting
edge and should be razor-sharp. Hone
it on the inside edge only. If the corner
of the iron projects beyond the side
more than just a hair, the nicker or spur
wheel might have to be shimmed with a
washer or bent slightly (like the set in a
sawtooth).
The rest of the tuning steps are
similar to those for any plane: Check and
lap the sole; tighten the handles if there
are any; for double irons fit the cap iron
to the iron; hone the underside of the
To tune a rabbet pl ane, here a #78 f i I I i ster, adjust the i ron so that it is
paral l el with the sol e and j ust proud of the side.
To tune a skewed rabbet iron, the back of the i ron al ong the shoul der
edge shoul d be beveled at l east as much as the skew angl e.
P L A N E S F O R J O I N E R Y 1 27
Thi s Japanese
fi I I i ster has an
adjustabl e fence,
a hol l ow-ground
knife ni cker, and a
rosewood sol e to
hold up to hard use
and wear.
lever or screw cap so that the iron is held
snugly (or in wooden planes check that
the wedge holds the iron tightly against
the bed); and check that the bed for the
iron is flat and true. A light coating of
wax on the parts will make adjustments
smoother. (Look back at Chapter 4 if you
have any questions about this tuningJ
One word of caution: With your plane
sharp and ready for work, handle it
carefully because the iron is so exposed it
can really give you a nasty cut.
Cutting rabbets with the grain
The simplest rabbet to cut is along the
long-grain edge of a board. You can use a
basic wooden rabbet plane to cut this
joint, but it's easier and more accurate to
use a fillister.
The Stanley #289 and #78 cast-iron
fillisters are just two of about a dozen
fillisters that Stanley made. Both have
spurs, depth stops, and fences. The #289
i s slightly more versatile, with spurs on
both sides of the plane, a depth stop that
1 28 C H A P T E R S E V E N
fits either side, and a wide, heavily
skewed iron. The # 78 has a bullnose
position useful for working up tight to a
corner. Both are accurate planes useful
for all but the heaviest ra bbeting work.
For heavy work, the bench rabbet
planes # 10, # 10 12, and # 1 0 V4 are ideal.
They are called bench rabbets because
they are essentially the same mechani-
cally as the #4 and #5, with a double iron
at the same pitch, an adjuster, and a lever
cap. Of these only the # 10, a so-called
carriage-maker's rabbet, is common.
This plane is a favorite of timber framers
for truing the faces of tenons and over
sized joints. The # 10 V2 is just a smaller
version, and the # 1014 the same size as
the # 10, only far more rare and with the
handy feature that the knob and rear
handle can tip to one side or the other to
avoid the problem of scraping your
knuckles when working close to a wall or
in tight quarters (see the bottom photo
on p. 1 25) . I would use any of these three
for working large rabbets for something
like a door or large window frame.
To explain how to cut a rabbet along
the long-grain edge of a board, I'll use the
example of a #289, which is one of my
favorite rabbet planes. The fence makes
it easy to cut a rabbet of consistent
width, and the depth stop ensures a
uniform depth. The skewed iron helps
where the grain isn't totally consistent.
Planing with the grain the spur isn't
necessary, unless the grain is very
irregular. Even then the nicker can get in
the way by causing the plane to follow
the grain rather than the fence.
To cut a l ong-grain
rabbet with a #289,
keep the fence
pressed agai nst the
gui di ng edge and
pl ane unti l the depth
stop prevents
cutti ng any deeper.
With the iron tuned, planing the
rabbet is not difficult. I set the fence for
the width of the rabbet-the distance
between the cutting corner of the iron
and the face of the fence. The depth stop
is set measured from the cutting edge.
With the iron set for a modest cut and
using long, even strokes, I plane down
the length of the board. My right hand
supplies the force and orients the plane
square with the cut; my left hand applies
consistent pressure to the fence to keep
the plane cutting squarely into the
rabbet (see the bottom photo on the
facing page). The rabbet is cut when the
depth stop just touches the surface all
along the board, or, working without a
depth stop, when I've planed to a scribed
depth line.
There are three problems you might
encounter when cutting a rabbet. The
most common is that the inside corner
of the rabbet steps outward with each
cut, making the rabbet progressively
narrower, as shown in the drawing at
right. What's happening is that the iron
doesn't project far enough from the side
to cut right up to the shoulder. The
solution is to tap the iron farther out
until it cuts a clean corner. A second
problem might be that the rabbet is not
parallel with the outside edge of the
board (not a consistent width),
particularly at the ends. All this means is
that you're not being careful enough
about keeping the fence tight to the
guiding edge. There is less fence to guide
the plane at the start and end of the cut,
so be particularly careful there. The
third problem is that the rabbet is not
parallel with the surface of the board,
which is caused by tipping the plane off
plumb. I check this periodically while
cutting the rabbet, with a straightedge
on edge along the surface of the board
and extending over the rabbet.
Planing Rabbets:
Com mon Pr oble ms
PROBLEM
PROBLEM
Smal l steps at the
shoul der
SOLUTI ON
Tap the iron farther out
from the side.
Shoul der not paral l el with the edge
SOLUTION
Apply even pressure on the fence
throughout the cut.
Cutting the same rabbet with a #78
without a fence or with a wooden rabbet
plane involves a somewhat different
technique. First, I mark out the depth
and width of the rabbet with a marking
gauge or pencil. To guide the plane I
either tack a cleat onto the surface in line
PROBLEM
Rabbet not paral l el with
the face of the board
SOLUTION
Make sure that the
plane is not tipped out
of plumb.
with the shoulder of the rabbet, tack a
temporary fence onto the side of the
wooden rabbet, or start the cut by
tipping the plane onto the shoulder
corner of the cutting edge and use my
palm or fingers as a guide along the
P L A N E S F O R J 0 I N E R Y 1 29
A qui ck way to start the cut when usi ng a wooden rabbet pl ane i s to ti p the pl ane onto its
corner so that it cuts al ong the shoul der l i ne fi rst. The shoul der then gui des the rest of the cut.
Use a wooden fence
to gui de the pl ane
when cutti ng a
cross-grai n rabbet,
here for the tenons
and cont i nuous stub
tenon for j oi ni ng a
breadboard end.
Set the ni cker
sl i ghtl y l ower than
the i ron to score
the fi bers and cut
a clean shoul der.
1 30 C H A P T E R S E V E N
board edge (as shown in the top photo at
left). This last method might seem a
little crude, but it is surprisingly accurate
and quick. Even if the initial cut isn't
perfectly straight, after a few strokes it
will be close; to make it really straight
I turn the plane on its side and cut along
the shoulder to the line. With no fences
in the way this is easy to do.
All of the same problems can occur
with a wooden rabbet plane or a # 78 as
when using the fenced #289. With these
planes, the side of the plane is guiding
the cut, so it's even more important that
the iron be ever so slightly proud of the
side and the plane be held tight to the
shoulder. It seems that no matter how
careful I am the inside corner still has
a little bit of a step. To remedy this I
turn the plane on its side and plane the
shoulder a few times to bring it back
to square.
Cutting rabbets across the grain
Cutting a rabbet across the grain is
nearly the same technique as cutting one
with the grain. The main difference is
that you have to use a spur or nicker to
cut a sharp clean rabbet. The nicker need
not be set very deep, perhaps '.:in. for
softwoods and half that for hardwoods.
If you're cutting rabbets on adjoining
edges, always cut any end-grain rabbets
first, so that any chipping of the end
grain fbers at the ends of the cut can be
planed away when cutting the long-grain
rabbet. There are three different
methods to help reduce or avoid this
chipping. One is to cut a fine saw kerf a
few strokes deep into the shoulder line at
the end of the rabbet. Another is to
scribe along the entire shoulder line
(down the edges, too) with a marking
gauge or knife against a straightedge. The
third method is to draw the plane
backwards from the end of the cut a few
times. The nicker scores the shoulder
line when you pull the plane back.
You might run into any of the same
problems cutting a rabbet cross grain as
when cutting long grain. Because most
end-grain rabbets are relatively short, it's
easy to cut out of parallel with the edge.
One thing I find that helps is to
undercut the size of the rabbet slightly
and then true up the shoulder by using
the plane on its side and working from
the far end toward me. This puts the
tuned side of the plane (the one with the
iron adjusted perfectly) riding along the
bottom of the rabbet. And when you
work backwards like this there's no fear
of chipping the end grain. It's also the
same technique more fully explained for
shoulder planes later in this chapter (see
pp. 146- 148).
Cutting tenons
Cut a cross-grain rabbet on both sides of
a part and you've cut a tenon. These
might be tenons on parts as narrow as
window-sash muntins or as long as the
stub tenon along a wide tabletop for
joining on a breadboard end (see the
bottom photo on the facing page). On
parts that are awkward to bring to the
table saw (where I cut most tenons),
cutting the tenon with a rabbet plane is
about as fast as setting up a router. I
mark out the shoulder line on both faces
first and then set the fence on my #289
to cut just shy of the line. Scribing the
shoulder line with a knife or sawing into
it at the far end helps avoid chipping. I
cut close to the final depth on both faces
and finish the cut with a heavy shoulder
plane-the best tool for the job-working
up to the shoulder line and final depth.
Cutting a series of narrow tenons
(such as for window muntins) can be
done in a similar way if the parts are
ganged together on the benchtop. I
clamp the work between dogs at right
angles to the front of my bench and
line up the shoulder lines. I work the
The best pl anes for cutti ng stopped rabbets are of a bul l nose desi gn,
wi t h t he iron set close to the toe. At rear is a craftsman-made boxwood
and brass bul l nose pl ane; in the center, a shapel y Engl i sh bul l nose
wi th ebony wedge; and at bottom an E. Preston Engl i sh bul l nose
si mi l ar to a Stanley desi gn.
rabbet down on one side, cutting one
face and shoulder of the tenon, and then
flip the pieces and cut the other face
and shoulder.
Cutting a stopped rabbet
A stopped rabbet is a rabbet that is cut
along only part of an edge; it can be
stopped either along the grain or across
the grain. Stopped rabbets are used
where you don't want the rabbet to show
or as part of the joint design. The first
step in cutting a stopped rabbet is to
chisel away the corner of the stop and an
inch or two of the rabbet to create a place
for the toe of the plane to plane into.
I either use a marking gauge to lay out
the shoulder to chop to or plane right up
to the stop, in which case the plane (or
nicker) defines the shoulder. Once the
wood is removed from the corner, I can
plane right into it as I cut the rest of the
rabbet. A bullnose rabbet plane (such as
the # 78 or #90) is handy for cutting the
rabbet because the forward position of
P L A N E S F O R J O I N E R Y 1 31
Dado pl anes are
speci al i zed rabbet
planes wi th a ni cker
with doubl e spurs
for scori ng both
shoul ders of the
dado ahead of
the i ron.
Thi s experi mental Stanl ey dado pl ane, si mi l ar to the #239, cuts a
groove across the grai n, in t hi s case for an i nlay band. There are two
i rons; one acts as a ni cker and the other actual l y cuts the shavi ng.
1 32 C H A P T E R S E V E N
the iron lets the plane cut close into the
corner. Using a chisel plane (described
on pp. 148- 149) is another alternative for
working the rabbet into the corner.
DADO PLANES
A dado is a groove cut within the surface
of a board across the grain. It has two
shoulders and a flat bottom. It's the kind
of joint used for housing shelves into the
sides of a bookcase, for joining the back
into the sides of a drawer, or for inlaying
a band into a surface. A sliding dovetail
with sloping shoulders is also a dado.
Dado planes are specialized rabbet
planes. They look very similar to rabbet
planes, with a few small differences; the
most obvious is a variation of the nicker
design. On wooden dado planes the
nicker can be a separate iron wedged
ahead of the cutting iron, vertical or
canted slightly forward, with two knife
like spurs. The spurs are fled into the
outside edges of the nicker iron and align
with the outside edges of the cutting
iron. On cast-iron planes there are
separate nickers on either side of the
plane, also in line with the outer edges
of the iron. Dado planes usually have
depth stops and skewed irons to work
cross grain most easily. They do not
have fences, so the plane can be used any
where on a surface. Another common
characteristic is a working sole that's
narrower than the width of the plane
body; in the case of the #39 dado planes,
Stanley made soles varying from '+in.
to 1 in. wide (see the top photo on the
facing page).
Tuning and using dado planes
Dado planes need all of the same tuning
as skewed rabbet planes, with one
additional step: The nickers or spurs and
the cutting width of the iron need to be
adjusted to one another. The iron should
be set so that it's just peeking out from
either side of the plane and in line with
the nicker. In theory, the nickers score
the fibers ahead of the cut and the iron
lifts out the waste. Working cross grain,
as a dado plane normally would, it's not
important if the iron is slightly narrower
as long as the nicker is scoring the
desired width of the dado. The grain is
weak enough in this direction to break
away and leave a smooth-bottomed dado.
Sighting down the sole will give you an
idea of whether the nickers and iron are
aligned; actually using the plane tells you
a lot more.
If the iron cuts a dado that's wider
than the nicker, I very carefully spread
the nicker spurs apart. It's the same idea
as putting set into the teeth of a
handsaw. Hold the iron on its edge
against a hardwood block and lightly tap
the spurs out with a small faced
hammer. On the Stanley line of #39
dado planes, however, adjusting the
spurs is not possible. But because of the
ingenious way the spurs are set into the
sides at an angle, exposing more of them
widens the cut they take. This allows for
a small amount of adjustment. To cut a
clean-bottomed dado, set the spurs (or
nicker) to cut slightly deeper than the
iron. Once everything is adjusted it's
likely to stay that way for years, that is,
unless you decide to start cutting all of
your dadoes with planes.
Traditionally, dadoes are cut by
sawing the shoulders and chopping out
the waste. A plane is a lot handier to use
out in the middle of a wide board where
it's awkward to saw. The cut is started
much the same way as for cutting a cross
grain rabbet: along a tacked-on fence and
either by scoring the end of the cut with
a knife, by drawing the plane backwards
a time or two (against a fence), or by
sawing the ends of the shoulders. Once
the plane starts cutting it guides itself.
For a stopped dado, saw and chisel out
the corner as for a stopped rabbet. A
Stanl ey made a series of dado pl anes, with skewed i rons, depth stops, adjustabl e ni ckers, and
sol e wi dths from % i n. to 1 i n. ( #39%, #39%, and so on) . The si mpl e wooden rabbet pl ane i n
t he background has a ni cker i ron wedged ahead of t he mai n i ron.
These unusual
curved wooden
dado planes were
made for cutt i ng
dadoes of a
speci fi c radi us for
architectural work.
P L A N E S F O R J O I N E R Y 1 33
A tongue-and
groove j oi nt is cut
with a pai r of
wooden match
pl anes, each de
si gned for a specific
thi ckness of stock.
The pl ane on top
wi th a steel skate
cuts the groove;
the other plane cuts
the tongue.
Match pl anes came
i n a wi de variety of
styles and sizes.
Thi s
h
ard-worki ng
pai r has rear
handl es formed
from the pl ane stock
and steel " pl ated"
fences to resi st wear.
bullnose dado plane would be handy,
but I've never seen one. A router plane
(discussed later in this chapter) is a good
tool for working into the corner.
I use dado planes mostly for cleaning
up the bottom oflong dadoes cut with a
table saw or a router. If I want an
1 34 C H A P T E R S E V E N
accurate, smooth, and flat bottom, a
dado plane is the best tool for the job. I
use a narrower width plane so it fits
comfortably in the dado and I can see
what I am doing. I have no doubt that a
couple of dado planes of different widths
would be handy in any shop.
MATCH PLANES
A tongue and groove is used to join the
edges of two boards just as the name
suggests: A groove is cut near the middle
of one edge, and the mating edge is cut to
form a tongue to fit this groove. This
joint is used throughout the woodwork
ing trades whenever an airtight,
watertight, or simple and strong joint
between two boards is called for.
Popularly, the boards so joined are
known as matched boards and the planes
that cut the joint as match planes.
Wooden match planes usually come
as pairs tuned to each other for a tight fit
between the tongue and groove. Each
pair is made for a specific thickness,
from Y4-in. boards to 1 Y2-in. planks (or
larger). The lighter of these planes (as
shown in the top photo at left) resemble
rabbet and molding planes-they have no
handles and are side-mouthed. Match
planes for working thicker stock can have
large, adjustable screw or wedge arms, or
a heavy body and rear tote more like a
jack plane (see the bottom photo at left).
Somewhat less common are single
planes, so called double-ended match
planes, that look like a pair of tongue
and-groove planes joined together. They
have two irons-part of the sole cuts the
groove, another part the tongue.
On all match planes, steel plates are
used for the sole of the plane that cuts
the groove. A wooden sole alone would
likely break off in no time or wear
quickly. Fitting the plane with a steel
"skate," as it's known, allows the plane to
cut a deep and narrow groove, gives
stable support to the iron, holds up to
wear, and stays true. Steel is also used to
reinforce and reduce wear on the face of
the fence of both planes (so-called
"plated" planes).
The grooving iron is similar to the
iron on a plow plane, tapered and
thickened toward the cutting edge. On
better-quality planes the iron has a
small groove ground into its back where
it beds against the skate. In quite an
ingenious design that keeps the iron in
line with the skate, the bedding edge of
the skate is sharpened to seat into this
groove. The wedge then holds the iron
tightly in place.
The tonguing iron is the reverse of
the groove, with a long rectangular slot
cut out of the middle. The cutting
edges to either side of the slot cut the
surface to leave the tongue. Most
matched-plane irons are bedded at York
pitch (50) for a slight advantage when
cutting hardwoods.
Cast iron considerably simplified the
construction of match planes and
allowed for some innovative designs. The
skate could now be made as part of the
casting of the plane body, along with a
strong and long-wearing fence and a
comfortable handle. And instead of two
planes, an early Stanley pattern (#48 and
#49) has an ingenious swing fence and
two irons that cut both the tongue and
I nnovative cast-iron
match pl anes com
bi ne the functi ons of
two pl anes i n one,
From the top, a
Stanl ey # 1 48 doubl e
end match pl ane
wi th two i rons and
shared fence; a
Stanl ey #48 swi ng
fence match pl ane,
and an early Mi l l er' s
patent match pl ane,
also by Stanl ey, wi th
a bronze wash on
cast i ron,
groove (see the photo above). In one
position the irons cut the tongue. Swing
the fence 1 80 and lock it in position,
and one iron cuts the groove. A later
pattern is known as a double-end plane;
it resembles a pair of match planes
joined side-by-side and sharing a common
fence. Planing in one direction cuts the
tongue, planing in the other the groove.
The combination planes #45 and #55
also cut various tongues and grooves. (For
more on these planes, see pp. 202-204. )
P L A N E S F O R J O I N E R Y 1 35
Tuning and using
match planes
Match planes are rarely used today,
except in restoration work, though I'll
sometimes use them just to enjoy the feel
of cutting a tongue-and-groove joint by
hand. I have a pair of wooden match
planes that are the right size for joining
boards for cabinet backs. If ! have only a
few joints to make, it's just as quick to
joint the edges and cut the tongue and
groove with these planes as it is to set up
the table saw or router. I use them like
any other plane, with continuous strokes
and pressure against the fence that rides
against the face of the stock. Both sides
of the joint are cut relative to the face so
that any inconsistency in their thickness
will be less noticeable and at the back
side. With a fence and depth stop cut as
part of the sole, it's rather easy to match
boards with these planes. Tuning them is
a little bit more challenging.
There are two things to watch out for.
The irons have to match one another for
size, and they need to be accurately
positioned relative to the fence so that
the faces of the boards in the assembled
joint will be flush. The tongue and
groove should make a neat fit-so that
the joint can be "tapped together with
your hat" as the saying goes. A little loose
is better than too tight. Adjust the fit by
honing the irons: Honing the sides of the
grooving iron will make it cut a narrower
groove; widening the rectangular cutout
in the tongue-cutting iron will make it
cut a wider tongue. As for positioning
the irons, a little trial and error works as
One of the earliest metal combi nati on pl anes,
thi s Phi l l i ps patent pl ow pl ane is cast of
bronze, wi th a rosewood handl e and fence.
I t i ncl uded a set of i rons and ni ckers for
pl owi ng vari ous-sized grooves, dadoes,
rabbets, and matchi ng tongues.
1 36 C H A P T E R S E V E N
Thi s unusual match
pl ane by one of
Stanley's competi
tors, a Sargent VBM
( " Very Best Made" )
# 1 068, cuts the
tongue wi th one
sol e and, when the
pl ane i s turned over,
the groove with the
opposite sol e.
well as anything. I've tried cutting a scrap
of wood whose width equals the distance
from the board face to the groove or
tongue. I use it like a gauge to adjust the
irons away from or closer to the fence.
Trying both planes on a scrap to see how
the joint goes together is the best test.
This tuning might be a little fussy, but
once the irons are set, the only
maintenance they will need is a little
honing once in awhile.
PLOW PLANES
Plow planes are simply grooving planes
with various-sized irons to plow grooves
of specific widths. They are the earliest
combination planes, used for cutting
grooves for such things as securing panels
in a frame, holding drawer bottoms in
drawer sides, or roughing out the profile
of a large molding before refining it with
molding planes. Although they might do
basic work, as plows evolved they became
anything but simple.
Early plows are no different from the
grooving plane of a matched pair, with a
single-width iron, steel skate, and fence.
By replacing the fixed fence cut from the
sole with an adjustable fence, the plane
was more versatile and useful. Adapting
the plane to fit various-sized irons made
it more useful still. Most planes were
supplied with a standard set of eight
irons from Vs in. to /in. wide. Eventually
the fence was made as a separate piece
with two arms connecting and securing
it to the plane body. With a widely
adjustable fence, grooves could be
accurately cut parallel to an edge any
where within a board up to about a foot
wide. These fences are often lavishly
molded on the long-grain and end-grain
edges, both for decoration and for a more
comfortable handhold.
Although most wooden planes were
slowly improved from one generation to
the next, few tools caught the interest of
Screw-arm plows adjust slowly but posi ti vel y. A nut on either side of
the pl ane body l ocks the boxwood threads.
inventive minds as did the plow. It wasn't
so much the body of the plane that
attracted them-it was improved, too
but the fence and arms, which posed
unique challenges. How could they be
secured to the plane, be adjustable, and
be held so that the fence accurately
guided the plow? And how to make the
fence and arms easily adjustable and
parallel with the plane body?
Early on, British plane makers came
up with one solution and Continental
makers came up with another.
Continental makers secured the arms in
the plane body and slid the fence along
them, with wedges to hold the fence in
position. British makers took the
opposite approach and fixed the arms to
the fence, which could be adjusted
toward and away from the plane body as
a unit. To hold the fence parallel to the
body, the arms were wedged into place
with keys or secured with brass or wood
thumbscrews tightened down from the
top of the plane. Both designs were
prone to binding or not staying in
adjustment. Given our shared heritage
and the influence of British tools, it's not
surprising that American plane makers
initially followed British prototypes.
Every woodworker who used a plow
plane experienced the same frustration
P L A N E S F O R J 0 I N E R Y 1 37
of having to set and then hold the fence
once it was in position. To adjust the
fence meant either tapping on the fence
or the tips of the arms, which if done
enough damaged their ends. One
solution was to tip the arms with brass.
Another was to find an easier way to
adjust the arms. Many possibilities were
tried, including going back to
Continental designs of fixed arms.
Threading the arms (often fine-grained
boxwood) and locking them in place
with large nuts against the plane body
was one idea that worked well (see the
photo on p. 137). Adjustment was
positive but slow. Another solution was
to have sliding arms (or fixed arms) and
thread a third arm to screw the fence in
1 38 C H A P T E R S E V E N
and out with. On some designs threaded
rods were put inside the arms or they
were fitted with rack-and-pinion gears.
Arguably the best solution was one
of the last: the center-wheel plow made
by Ohio Tool and Sandusky Tool in the
last quarter of the 1 9th century (see the
photo on p. 1 20). The fence has three
arms, two for support and the center one
to adjust the fence with a large brass or
boxwood wheel-the center wheel. It
wasn't that simple, though. In order to
adjust the fence, the center-wheel arm
had to be threaded in opposite directions
to either side of the wheel. If it wasn't,
the center wheel would move in and out
but the fence would stay put.
While these designs were suitable for
a carpenter or a furniture maker,
coachmakers needed a tool that could
plow curved grooves. This took some real
invention. Two variations of the
coachmaker's plow were made. In one,
the body of the plane was radiused
(concave or convex), with a straight fence
for such work as plowing a groove in a
flat door for a curved panel. In another,
the fence was curved and the plane body
was quite short to plow along a radius
(for examples of both, see the top photo
on p. 21 8).
By the mid- l S70s the catalog of any of
the larger wooden-plane manufacturers
offered perhaps as many as 50 plows, of
different woods, qualities, and styles.
They ranged in price from a basic beech
plow selling for about $4.00 to ebony
and rosewood models with ivory or silver
tips for $25.00 or more. Clearly the
sheer numbers of plows available, all
doing the same basic work, gives some
idea of the degree to which these planes
captured the imagination of all wood
workers. The quality of a craftsman's
plow spoke of his status, so it's no
wonder that craftsmen traded up as
they could afford a fancier tool (even
though it worked no better)' In a final
act of acknowledgment, examples of the
finest plows were often given as
retirement gifts.
The concept and utility of the plow
plane did not disappear with the passing
of beautiful wooden planes. They might
Engl i sh cast-i ron pl ow pl anes are uncommon,
but none i s more unusual than thi s Howki ns
model C, made c. 1 920 and desi gned to cut
curved grooves, at angl es, or even wi th
dovetai l ed si des. So few were made that the
ori gi nal l abel and i nstructi ons were hand
wri tten at the factory.
not be made of the same beautiful
woods, but in terms of a practical tool
the plow lived on in cast-iron designs and
later in the combination plane. Stanley
made at least four different combination
planes that used between seven and ten
plow irons of various widths, including
the #45 and #55 (see the photos on
pgs. 184 and 203). And just as wooden
plows were beautiful beyond their
utilitarian needs, early cast-irons plows
were decorated with fancy filigree (see
the photo at right); the fences, skates,
and arms were gracefully curved or
ended in curves; and the planes were cast
of beautiful gunmetal or were nickel
plated. They couldn't help but catch the
eye and aspiration of any craftsman.
Tuning and using plow planes
I've used a plow plane but little-just
enough to get a feel for the tool. Unless
you want to do things in a traditional
18th-century manner, a router or a table
saw is a more efficient (though noisier)
alternative. Still, no tool quite symbolizes
planes and hand tools as does a finely
made and beautiful plow. The best are
functional sculpture, from the delicately
shaped and polished thumbscrews to the
ornately molded edges of the fence.
Despite what might look like a compli
cated plane, a plow is quite easy to use.
Three adjustments are necessary. The
fence needs to be set parallel to the plane
body and the required distance from the
iron; the iron must be set for the depth
of the cut; and the depth stop needs to
be set for the depth of the groove. The
width of the iron determines the size of
the groove. Odd-size grooves are cut with
two passes of a smaller iron (with a lot
more difficulty, since an iron the same
width as the groove hel ps the plane
track). The iron wedges into place as in
any wooden plane, but to make setting
Thi s Mi l l er's I mproved Joi ner' s pl ow pl ane by Stanl ey Rul e and
Level , 1 872, i s an extremel y rare earl y combi nati on pl ane. The
casti ngs were adorned wi th beauti ful floral decoration to i ncrease
the appeal .
i t easier i t has a "sneck," or small offset,
at its top (see the photo on p. 120).
Tapping upward on the sneck removes
the iron or reduces its cutting depth;
hitting downward on the end of the iron
sets it deeper. The iron can be set for a
coarse cut, since any roughness at the
bottom of the groove will I ikely be
hidden. The final adjustment is the
depth stop. Simpler plows have a wooden
stop held in a groove by either friction or
a thumbscrew; fancier versions have a
brass thumbscrew and a stop along
the skate.
Plows don't cut as smoothly as many
other planes. For one thing, although the
iron is supported well enough from
behind, the skate in front doesn't form
much of a throat. With a wider iron, the
skate in front does little or nothing. Still,
if the iron is sharp and the grain is not
too unruly, you can plow a satisfactory
groove. Keep steady pressure on the
fence, hold the plane square with the
work, and take continuous strokes. Not
surprisingly, it's a captivating tool.
P L A N E S F O R J 0 I N E R Y 1 39
DOVETAIL PLANES
For me, dovetail planes have some of the
same allure as plow planes. A number of
years ago I was at one of Richard Crane's
special fall auctions (see pp. 246-248).
I had my eye on a few tools-one of them
a Stanley #444 dovetail plane. It was
right about lunch time and the crowd
was getting fidgety when Richard started
the bidding. "Where to start this plane,
boys? Do I hear $ 100?'' Now this was a
plane I rarely saw come up for sale, but
when one did it sold for closer to four
figures than three. As a dedicated plane
user, I had always imagined that this
would be the tool for cutting sliding
1 40 C H A P T E R S E V E N
dovetails or accurate tapered ones.
When the bidding got up around $ 1 50
I jumped in, just about the time the few
bidders either paying attention or
interested dropped out. With hardly any
more bidding, the plane was mine.
The #444 is one of the most daring
and complicated planes that Stanley ever
made. No other manufacturer even
attempted to make such a plane, although
wooden versions were available (though
uncommon) for at least a few hundred
years before. Wooden dovetail planes
were more common in Europe, where
the joint they cut is known as a "French"
dovetail. My #444 is a beautiful tool, all
nickel-plated and nicely detailed and
finished. For reasons I now understand,
it has seen little if any wear. It has three
main parts-a main body, a square fence,
and a beveled fence-and four cutters. It
cuts a sliding dovetail '+ in. wide or
wider, and as deep as `1 in. Despite its
range, more than one craftsman has
disparagingly described it to me as a
"boat anchor." An expensive one at that.
Over the years I have owned it I've
used it a little and would have to agree
somewhat with these sentiments. It's an
awkward tool to use, no matter how
versatile. Just setting it up is a challenge
all those angled parts to align-to say
nothing of tuning everything into
harmony. Using a router for all of the
same work is a snap in comparison. But
what I have to keep in mind is that this
tool predates routers by quite a few years
and for a long time it was the best tool
for cutting a complicated and very useful
joint. Yet I suspect that even 75 or more
years ago craftsmen who had the #444
available chose to use other tools, or
make other joints. This is why they are
somewhat rare and few show much sign
of use. I don't expect my #444 to see
much wear in my lifetime either.
PLANES
FOR CUTTING MITERS
Miters are the angled cuts made along
edges to form a neat joint between parts,
to hide some part of the joinery (such as
a set of dovetails), to add to the joint's
strength, or to cover end grain. Miters are
of three basic types: frame miters, case
Stanl ey' s uni que dovetai l plane #444 cuts
sl i di ng dovetails of vari ous wi dths. Before the
days of mechani cal routers, i t was the best
tool to cut thi s di ffi cult j oi nt accurately, but it
requi red two separate fences and setups to
cut the mati ng parts.
M i te r J oi nts
FRAME MITER
miters, and edge miters (see the drawing
above). A frame miter is the typical
corner joint of a picture frame. A case
miter is cut along the end-grain edge, as
for a case of some kind or to join the ends
of boards for a blanket chest. Edge miters
are cut with the grain along an edge for
such things as coopered work. While any
of these miters can be cut freehand,
shooting boards greatly improve accuracy
and speed the work.
Frame miters
A frame miter is not particularly strong
without some other means, such as nails,
screws, or splines, to strengthen the
joint. And where the frame members are
wide, as on a door or window casing, the
miters will open and close as the
humidity levels change no matter how
well they are fit. Nevertheless, the frame
miter is a useful joint and in some cases
the only joint to unite parts neatly. In the
case of joining two parts with a molded
surface (a picture molding, for example),
a miter is the only practical way to join
the two and maintain a continuous flow
of the profile.
CASE MITER
M i te r Shooting Boar d
Workpi ece
Use plane on side.
Most miters are cut at 45, so the
parts join together and form a square
corner. A shooting board made at this
angle will suit most of your needs. For
odd-angled miters, working freehand
will probably suffice.
To cut a clean and sharp miter that
meets at 90 is quite a bit harder than it
EDGE MITER
45 fence
groove
might seem. I have a number of different
size shooting boards for mitering any
thing from small stops to secure glass in a
frame to wider moldings. Each is made
with a 45 fence, as shown in the
drawing above. The fence is actually two
fences in one, with two positions for the
P L A N E S F O R J O I N E R Y 1 41
M I T E R S H O O T I N G C L A M P S
A
miter shooting clamp is a
jig for trimming miters;
as the name suggests, it is part
shooting board and part
clamp. The two large jaws of
the clamp are cut at 45 ; one
is fixed and the other slides in
a slot, with a wooden screw
applying the clamping force.
With the work clamped
securely between the jaws,
their bevel orients the plane,
making it fairly easy to cut an
accurate miter. Miter shooting
clamps work best for frame
and case miters of modest size
or for cutting miters on any
parts with edges square enough
to be clamped securely.
In shops of a century ago,
when all miters were cut and
trued by hand, a miter
shooting clamp was a common
sight. While it might be nice
to have one, unless you are
going to be doing a large
amount of this sort of
mitering, such as making
picture frames for a living, I
would save the considerable
time needed to build such a
clamp and make simpler ones
that suit each situation. Old
miter clamps are not that
common or inexpensive
either. Another alternative is
to use a Stanley shoot board
and plane (see the sidebar
on p. 144).
A miter shooti ng cl amp gui des a pl ane to cut accurate mi ters on any
work that can be cl amped between the jaws.
work so that I can always plane toward
the long point of the miter for a clean
and accurate cut.
In planing miters with any shooting
board and a bench plane on its side, it's
important that the plane's sole and side
be perfectly square. The iron must be
parallel with the sole, too. The plane's
length is not that important, since most
miters are short, so tune up a #4 or #5
for the work or use a miter plane made
just for this purpose (see the photo on
p. 1 1 0).
1 42 C H A P T E R S E V E N
Actually cutting the miter is no
different than shooting an end-grain
edge-in fact, it's easier. The cut is
partially long grain, partially end grain.
I position the work to plane from the
inside of the miter toward the point,
supported against the fence so there is
little chance of splintering it as the plane
cuts by. IHm cutting the miter freehand,
I mark it out with a pencil line, saw close
to it, hold the part in a side vise with the
miter level, and plane toward the point,
as shown in the photo on the facing page.
Light cuts and a slight skew prevent
splintering. As I work, I check the miter
with a small square to make sure that the
edge is square to the face; as I get close to
the miter line, I check the angle with a
bevel square set to the desired angle.
Case miters
A case miter is cut where two end-grain
edges meet, as, for example, at the
corners of a box or crown molding. The
miter is typically 45, but with
something like a multisided box or an
irregular corner, it can be any angle. By
itsel( the miter is weak (just as a frame
miter is), but it can be strengthened with
nails, screws, wooden splines, or even a
set of hidden dovetails set into a mortise
cut into each miter. Shrinkage across the
grain is not a problem, because the grain
is oriented in the same direction for both
pieces and they move together.
To cut the neatest case miter, the
parts must be flat and accurately thick
nessed. Even if the parts are thicknessed
by machine, check for and plane out any
cup with a bench plane. (Otherwise, the
miter may be neat but the cup will be
noticeable against the mating piece at
the corner. ) If the parts are molded, cut
the profile before mitering. If you have
only a few miters to cut, you can cut
them freehand, although the wider the
piece the more difficult it is to do. If I am
cutting a number of miters, I build a
shooting board known as a donkey's ear
for the easiest and most consistent
results. This shooting board is
constructed so that the work rests at the
proper angle against a stop and is
oriented to the plane cutting on its side.
I've got one built at 45 that clamps into
my side vise (see the drawing below).
With a stop in the middle of the
shooting board I can hold the work on
either side and plane into the stop to
prevent splintering. For parts with
molded edges, the side with the
straightest profile bears against the stop.
If you have a lot of similar parts to cut,
the stop could even be profiled to a
mirror image of a molded part (see the
drawing on p. 1 1 6). I mark out and saw
the miter and then place it on the
shooting board slightly proud of the
edge. When the plane iron just contacts
the edge of the shooting board I stop.
Working freehand, I mark out the
miter carefully along the top and bottom
edges and both faces, saw the waste, and
then plane up to the line using light cuts.
I check the miter angle with a long
straightedge and a bevel gauge set to the
miter angle.
Donke y ' s - Ear
Shooting Boar d
Stop
Frame miters can
be pl aned qui ckl y
by cl ampi ng the
pi ece i n a vi se and
pl ani ng toward the
poi nt with a low
angl e bl ock pl ane.
Use plane on side.
Clamp shooting board in side
vise or between bench dogs.
P L A N E S F O R J O I N E R Y 1 43
S TA N L E Y # 5 2 S H O O T B OA R D A N D P L A N E
here there was a need
for a special tool, in
this case for cutting accurate
miters, Stanley was happy to
supply it. The Stanley #52
shoot board and plane was just
such a tool-a universal
shooting board and plane
adjustable for a wide range of
miters. In 1 91 5, when a #4
Bailey bench plane cost $2. 20
or the complete #45 $7.00,
the #52 cost $ 1 0.00. Even
today, these tools are relatively
rare and sell for a few times
the cost of a good chopsaw
their modern replacement.
The shoot board is a ribbed
casting, carefully made for
strength and lightness. The
plane, slightly longer than a
jack, rides in a wide groove
down the length of the shoot
board. The groove is adjust
able to allow for wear. The
plane has an accurately
machined side that rides in
this groove, a skew iron for a
shear cut, and a rear tote
comfortably angled for using
the plane on its side.
The real beauty of this tool
is the adjustable stop that
swivels like a table-saw miter
gauge and locks in any
Edge miters
position. It has two additional
features: a clamp for holding
the work and a sliding back
that can be adjusted right up
to the cut to support the work
and prevent splintering. For
irregularly shaped work a
custom wooden fence can be
made and attached to the
adjustable stop.
There is no doubt that this
is an expensive tool, especially
for a craftsman who doesn't
cut a lot of miters. Although it
would be time-consuming and
challenging to make as fine a
tool yourself, there are plans
and instructions available (see
Kingshott's Making and
Modifying Woodworking Tools,
listed in the bibliography).
A Stanley shoot
board and pl ane is
a very accurate tool
for cutting miters.
The heavily skewed
i ron gives a cl ean
sheari ng cut on
work hel d agai nst
a stop that adjusts
over a wi de range
of angl es.
Another alternative is to make
a hardwood version and attach
different fences to suit the
work. For the plane, you can
often find orphaned shoot
board planes at tool sales or
through old tool dealers. Some
of these planes are
manufactured, others are
craftsman made, but most are
priced quite reasonably.
An edge miter, the last of the three miter
types, is cut along the grain, for example,
where two stiles meet at the corner of a
case or where coopered parts are joined
together. It's a strong and stable joint
that doesn't require additional fastenings
such as splines, though driving a few
Ys-in.-Iong brads (with heads snipped
off) into the inside of the miter makes
aligning the joint easier when gluing.
A donkey's-ear shooting board can be
helpfu I for cutting an edge miter if the
parts are short. In this case, the piece
butts against a stop and is held along the
shooting board with clamps. If it's
important that the parts be finished to a
consistent width, I add a second stop
along the length of the shooting board to
1 44 C 1 A P T E R S E V E N
butt the opposite long edge against. The
stop should be parallel with the front
edge (or skewed for tapered parts).
If I'm cutting only a few miters or
parts that are too long for the shooting
board, I prefer to work freehand or with
a jointer gauge attached to the sole of my
#5 or #7 bench plane (see pp. 108-109).
This way, I can see the cut a lot better to
adjust the pressure on the plane to fine
tune the bevel, and I can save the time it
takes to make the jig. With some oddly
shaped parts this is often the only way to
cut a bevel easily. The jointing technique
was described in Chapter 6. Quite
simply, I mark out the bevel on the end
grain and plane close to it with a coarsely
set plane. I refine the bevel with a fine
cut, checking the angle occasionally with
a bevel gauge. The longer the edge, the
longer the plane I use.
Planes
for Adjusting Joints
Cutting strong joints involves more than
just sizing the parts and sawing,
chiseling, and planing them to fit. Take a
simple mortise and tenon, for example.
Your first thought might be that the
tenon is doing most of the work,
securing the joint from pulling apart and
giving it rigidity. Actually the shoulders
of the tenon and the face of the mortise
are doing every bit as much. Any stress
on the joint presses these parts together,
so they need to be large enough and mate
well to give the joint real strength. The
best way to fit these parts is with a sharp
shoulder plane and a block plane.
There is another aspect of good
joinery and fine work that I like to call
clarity. Not only do the parts of a joint
need to fit well internally, but what's
visible should be sharp and concise. This
isn't to say that transitions and edges
need be square, far from it, but that each
element should have distinct definition.
In just the same way that it's hard to get a
really good edge joint between two
boards straight off a jointer, joints with
the most clarity have shoulders and faces
cut with a sharp plane.
Just as there are planes designed to
cut joints, there is a whole range of
planes for fitting them. Sometimes one
plane can do both jobs, but more often a
tool is better suited to one task or the
other. Four joint-adjusting planes that I
use often are shoulder planes, chisel
planes, router planes, and side rabbet
planes. All of these planes work best
when they take light paring cuts.
Shoulder planes are heavy rabbet planes
with a fine mouth and an iron bedded at
a low angle. A chisel plane has its iron at
the toe of the plane to cut into a corner
or tight place. Router planes deepen a
groove or cut it to a consistent depth.
And, lastly, unusual side rabbet planes
cut along the shoulder line to widen or
adjust a dado or rabbet.
Stanley shoul der rabbet pl anes #90 (fore
ground) , #92, #93, and #94 (a #91 was never
made) are accurate and heavy pl anes, wi th
i rons bedded at a l ow angl e, adjustabl e
t hroats, handy mi l l ed depressi ons for a com
fortabl e gr i p, and chrome or ni ckel plati ng.
P L A N E S F O R J O I N E R Y 1 45
SHOULDER PLANES
Shoulder planes are among my favorite
planes. They are some of the most
beautiful shop tools ever produced,
made from rich materials such as
gunmetal, rosewood, ebony, polished
steel, and nickel-plated cast iron. They
have a heft and size that feels good in my
hands. I use various sizes for truing the
shoulder of a tenon or rabbet (hence the
name shoulder plane), but they work
equally well wherever I need to make
fine and precise adjustments of a part
and require a rabbet mouth.
Shoulder planes look like any rabbet
plane, with a rabbet mouth and an iron
that peeks through the side. Traditionally,
they are metal planes, either wholly of
The tradi ti onal
Bri ti sh shoul der
pl ane at top has
gunmetal si des and
mahogany i nfi l l ,
combi ni ng beauty
and adequate mass
to work excepti on
ally wel l . The two
smal l er bul l nose
pl anes are solid
metal and have
shapel y wedges.
1 46 C H A P T E R S E V E N
cast iron or gunmetal or fabricated from
dovetailed-together steel plates with
exotic wood infill (see the photo below).
Generally, they are a lot smaller than
rabbet-cutting planes, although there are
some British shoulder planes that are
quite large. The sole and sides are
machined or lapped precisely square so
that the plane can be used on its side to
accurately shoot the shoulder while
guided along the tenon or the bottom of
the rabbet. A nicker isn't needed,
because these planes cut cleanly with
light paring cuts.
Most of the work of shoulder planes is
cross grain. For this, the iron is bedded at
about 200, with the bevel up as for block
planes. With the iron sharpened to a
bevel of 250 , shoulder planes have the
same basic cutting dynamics as a bench
plane. (I have one plane with an iron
beveled closer to 200 for softwood end
grain. ) The only difference is that in
this configuration the sole supports the
iron right to the cutting edge, preventing
the chatter more likely when cutting
tough end grain. Although not typical,
some planes have skewed irons. Some
shoulder planes have the iron close to the
toe of the plane, a design known as a
bullnose. I've got a Scottish plane by
Spiers that has both the bullnose and
normal position for the iron, as do the
new Clifton "three-in-one" planes made
in England.
The classic shoulder plane is the
British "stuffed" pattern (see the photo
on the facing page). These are heavy, fine
mouthed planes, carefully made to last
many, many generations. None of these
planes have adjusters. The most common
shoulder planes are the Stanley designs,
the #90, #92, #93, and #94 (a #91 was
never made for some reason). The #90 is
a bullnose rabbet, the #92 to #94
gradually larger versions of the same
plane (see the photo on p. 145). All have
adjusters. The Stanley cast-iron design is
basically similar to the British pattern.
Recently available are a few of the
beautiful and heavy Preston designs,
once made by Stanley's biggest English
competitor. And for those wanting the
challenge, kits can be bought to make
your own classic shoulder plane.
If I could own only one shoulder
plane, I would choose the #93. It's
simple to use, accurate, and the right size
for a wide range of work. A nicely
knurled knob on fine threads adjusts the
iron's depth easily, and the throat can be
brought up very fine. It has another nice
feature, which it shares with the #92 and
#94, namely that the whole front of the
plane is removable to convert the plane
to a small chisel plane. This gives me the
versatility of two planes in one.
Tuning shoulder planes
Shoulder planes are used for precise
work, and the more careful the tuning,
the better they will perform. These are
some of the planes worth spending all of
the time that you saved not completely
tuning your jack, scrub, or other coarse
cutting planes. But since shoulder
planes are made for fine work and are
more carefully manufactured and
finished because of it, most will need
only minor tuning.
All of the same characteristics that
make any precise plane cut well apply to
shoulder planes. Take special care with
three areas: the sole, which should be
flat and square with both sides of the
plane; the bed for the iron, which should
be flat; and the iron, which should be
carefully sharpened and parallel with the
sole. Before buying an old plane, check
Use a shoul der
pl ane, here a Spi ers
pl ane with rose
wood i nfi l l , to adjust
and true a tenon' s
shoul der.
that the sides are accurately machined
flat and square with the sole, because
lapping the three faces square with one
another is a real chore. None of this
tuning is different from that already
explained for rabbet planes in particular
and tuning in general in Chapter 4.
Using shoulder planes
I use shoulder planes by far the most for
fitting the shoulders of tenons, and
sometimes for sizing the tenon itself.
Considering how many tenons there are
in a set of cabinet doors or a table, this
can be quite a bit of work. And the fact
that even the slightest misfit of the joint
shows up as a dark gap at the shoulder
line makes these tools invaluable for
cutting strong and tight-fitting joints.
To adjust the shoulder of a joint I lay
the part flat on my bench, butted up
against either a bench hook or one of my
wooden bench dogs (see the photo
above). Even though I take paring cuts
and use the plane one-handed, it still
takes enough force that lcan do better
work if I help support the part against
P L A N E S F O R J O I N E R Y 1 47
something. I could just as easily clamp
the part, but I like to be able to pick it up
for trial fitting, to shift it to a new
position, or to pare it with a chisel. I lay
the plane on its side on the tenon and
plane along the shoulder line. All of the
same problems can occur as with a
rabbet plane, with the same solutions
(see p. 1 29). And planing by the end can
splinter out the fibers. To prevent
splintering I often stop just shy of the
end and pare the last '+in. with a chisel,
or flip the plane around and plane
toward me for a short distance.
A shoulder plane cuts a straight and
square shoulder. I use one after either
chopping the shoulder or cutting it with
a table saw. Neither method gets it quite
as true as a pass or two with a shoulder
plane. As I plane I can look down and see
any gaps between the sole and the
shoulder line. When the sole lies flat
along it over the whole length, I stop
planing. The only drawback is that it's
useful only for square shoulders or
where the angle between tenon and
shoulder is greater than 900
The beauty of these tools is that they
can cut just the thinnest of shavings in
fitting a joint. Don't think of them as
limited to cutting shoulders, though.
Anytime I need a small and precise
rabbet plane, this is the tool I reach for.
CHISEL PLANES
Chisel planes are unusual in that they
have no sole in front of the iron. They
look like a chisel iron held in the back
half of a plane body (see the top photo at
right). This design makes the tool
challenging to use because, with no sole
out front, the iron wants to dive into the
cut, making the plane hard to control.
Early chisel planes were simply
wooden bodies with a plane iron wedged
or screwed into place. I have a European
chisel plane that looks like a wooden
1 48 C H A P T E R S E V E N
Wi th the cutti ng edge ri ght at the toe, thi s craftsman-made wooden chi sel pl ane is i deal for
worki ng i nto tight corners or into areas i naccessi bl e with other pl anes.
Stanley made a
si ngl e-size chi sel
pl ane, a #97,for
" Pi ano Makers and
al l Cabi net Workers"
(center). Today,
Lie-Ni el sen makes
a smal l er version
i n cast bronze
(foreground) .
molding plane cut in half. Even the iron
is bedded at the same angle-a far too
steep 50. Stanley made a rather large
cast-iron pattern they called a "cabinet
maker's edge plane! (#97). The iron is at
a much lower angle ( 1 5 ), making it
more of a paring tool. But like a lot of
antique specialty planes, it's rare and
expensive. I had my eye on one for a long
time, but I couldn't justify spending that
much on a plane that might not earn its
keep, especially when a chisel by itself is
often just as handy. So when Lie-Nielsen
came out with two sizes of their version
of the #97 for a lot less money, I bought
the smaller one.
A chisel plane isn't a tool that you are
apt to use a lot, but there are times when
it's the only plane for the job. Even
though catalogs describe it as the perfect
tool for removing glue and for trimming
dovetails or plugs, I use it mostly for
cleaning into tight places, for such things
as stopped rabbets and chamfers. The
sole helps me to cut a smooth and
consistent surface right up to where the
cut ends-better than I can do with a
chisel. As long as I keep the cut light, tear
out is only a minor problem. The iron
has to be very sharp, too, so I wouldn't
recommend planing much glue.
Chisel planes need only the usual
tuning. Since they are essentially a form
of rabbet plane, they should be tuned
the same way. For the best control, the
iron should be parallel with the sole. To
adjust the cutting depth, I slowly lower
the iron, all the while trying the plane on
a scrap. When it starts to cut the finest
shaving, I start in. The only other trick is
to keep pressure well back from the
cutting edge, with your palm centered
over the knob at the heel of the plane. At
least in this position I'm able to balance
out most of the natural tendency of the
iron to dive into the wood and lift the
toe of the plane.
Router pl anes for worki ng i n grooves were often craftsman-made to suit some specifi c need,
so they can be found i n a wi de assortment of styles and materi al s. The si ngl e i ron cranked at
a ri ght angl e worked at a low cutti ng angl e for a smooth fi ni sh.
ROUTER PLANES
Today the motorized namesake of router
planes is far more likely to be used for
both cutting and fine-tuning grooves and
recesses. While I'm far from a purist and
not against routers, there are still a lot of
places where a router plane works
better-and certainly a lot more quietly.
I use one for deepening and smoothing
the bottom of grooves and shallow
mortises and for cutting a consistent
depth recess for an inlay.
It might not be the most politically
correct name, but one of the oldest
router patterns is known as an Old
Woman's Tooth (OWT). Like all routers,
the sole and bed of the plane have many
forms, but the iron is usually small and
square and it projects below the sole-
resembling an old hag's single tooth.
The iron can even have a slight flare
toward the cutting edge as a tooth does.
One trait all router planes share is a
throat open enough to see down into the
recess or groove that the iron is cutting.
Stanley and others perfected a cast-iron
design with two large knobs to grasp
and control the plane, a large throat
(sometimes open) to see into the work,
and a cutter that could be adjusted up
or down (# 71 and # 7l 12).
The Stanley router has a different iron
design from many traditional routers,
not like the iron in an OWT router, but
bent at right angles so that part of the
iron acts as a sole of sorts. Dynamically,
this orients the iron at a much lower
angle and gives a smoother finish
P L A N E S F O R J O I N E R Y 1 49
A Stanley router #71 % came with two different i rons, an adjuster to set thei r depth, and l arge
mapl e handles for a good gri p. The smal l er router, a Stanl ey #271, is an extremel y useful tool i n
t i ght pl aces.
because of it. For heavy work, the # 71 or
#71 ': is an excellent tool. Where router
planes surpass mechanical routers is in
working a convex or concave groove to a
consistent depth, in finishing the end of
a stopped dado or groove, or in working
in a tight place. My #71 ': came with an
additional beveled and sharply pointed
iron that works like a "V" snowplow and
cuts with little resistance. It's good for
cleaning into tight corners, whereas the
square iron is best for working long
grooves. The sole has two holes for
attaching a custom wooden sole-for
instance, one beveled or shaped to
support it against a molded workpiece.
I have a small router plane made by
Record (the Stanley #271 ) that is gem of
a tool. It has two iron positions, either
normal or bullnose, and an iron narrow
1 50 C H A P T E R S E V E N
enough to work in the smallest places.
I use it for stopped grooves for drawer
bottoms, case backs, or anywhere it fits
the work better or more comfortably
than my larger router plane.
None of these router planes are hard
to tune or to use. The only challenge is in
sharpening the bent irons. They can't be
ground or honed easily in the normal
way, so I end up bringing a fi ne slipstone
or the edge of a square stone to the iron.
Hone the "sole" or back of the iron as
you would a bench-plane iron. Take care
to work the heel a little more than the
cutting edge to create a slight relief angle;
otherwise, the iron will ride along on the
heel and won't cut. I always use a modest
to light cut, since any tea rout will likely
be hidden at the bottom of a groove. For
the neatest job deepening a groove, I cut
with a knife along the shoulder, using
the shoulder to guide the knife edge. It's
the same thing a nicker would do if there
was one.
SIDE RABBET PLANES
Side rabbets are as interesting, unusual,
and useful as the other joint-adjusting
planes. They almost always come in
"handed" pairs, that is, two planes, one
of which works left to right, the other
right to left. This way you can always be
working with the grain in any situation.
Even in patterns that are one plane,
there are two cutters facing in opposite
directions, or in the case of some English
patterns, coming out opposite sides of
the plane. Another unusual feature is
that the side of the plane usually guides
the cut (hence the name) and sometimes
even the side of the iron does the
cutting. These unusual traits let the
plane trim and widen grooves, dadoes,
and sliding dovetails or tune tight
molding profiles.
One of my favorite planes of this
group is the wooden version known as a
snipe bill. It looks like any other molding
plane with a profiled sole, except that
there is no throat and no iron projecting
through it. Instead, the iron is quite
vertical and peeks out from the side,
which acts as the sole. The narrow
curved point of the sole is reinforced
with boxwood and resembles the snipe
bill of the name. More common and
easier to tune and use are the Stanley
pattern #98 and #99 (a pair) or the #79,
a two-in-one plane. On any of the three,
the toe piece comes off for working right
into a corner or tight place. The # 79 is
available new, complete with a fence. My
only problem with this tool is that no
matter which direction I cut with it, one
of the irons is dragging and dulling. The
irons are hard enough to sharpen and
adjust as it is.
I'll use the #98 as an example to
explain tuning and adjusting the iron.
Si de rabbet pl anes cut al ong the shoul der of rabbets and dadoes to wi den them to fit other
parts. These two pl anes with crisscrossed iron patterns are by Stanl ey competi tors: The upri ght
pl ane in the background ( #81 ) is by Sargent of New Haven, Connecti cut; the other fanci er
versi on with adjustabl e i rons is by E. Preston of Bi rmi ngham, Engl and.
Si de rabbet pl anes
ei ther have two
i rons or come i n
"handed" pai rs,
such as the Stanley
#98 and #99 shown
here. Both pl anes
have depth stops
and a removable toe
pi ece for worki ng
i nto a corner.
The iron is angled across the side,
downward toward the throat. Two things
must happen at the throat: The cutting
edge must be parallel with the side
(acting as the sole), and the lower point
of the iron should barely peek out the
bottom (the true sole) of the plane. With
the iron slightly below the bottom, it acts
as a nicker for cross-grain planing. The
trick is to adjust everything together.
Tapping the iron deeper brings the point
further below the bottom, which isn't a
problem as long as it's not too far below.
If the iron is above the bottom, the
shoulder won't be cut its full depth. And
if the iron is not parallel with the side,
the shoulder will be cut at a bevel.
Trial and error seems to work as well
as anything. Sometimes I have to hone
the iron to bring everything into
adjustment. But once side rabbet planes
are tuned, they are the only planes that
can work in a narrow groove or dado and,
fine shaving after fine shaving, widen it
to fit a tenon. Since the sole is so narrow
and the plane short (at least the #98 and
#99 are), these planes can work in the
tightest places. With a light cut, they
work as well cross grain as with the grain.
Cutting strong, precise joints with any
of these planes takes patience, sometimes
creativity, and certainly an under
standing of the specific characteristics of
each tool. But it doesn't require a lot of
different planes. With a simple rabbet
plane, a shoulder rabbet (that separates
into a chisel and bullnose plane), a
narrow dado, a router, and a side rabbet
plane, you can cut and fit almost any
joint, with or without the help of
machines. When you see the clarity of
the joints cut with planes, you'll likely
want to add a few more planes to your
toolbox. Even if your shop is equipped
with all the latest machinery, there are
times when a plane and skilled hands are
still the best tools.
P L A N E S F O R J O I N E R Y 1 51
PLANES F OR S UR F ACING
Spiers planes . . . are not only a luxur but a necessity t every superior
woodworker No journeyman can be without one, and it is the ambition
of ever apprentice t possess one.
-c. 1930 catalog for Spiers planes, a competitor of Norris
Nothing really finishes the surface
of a board as well as a smoothing plane.
Not a planer, which mars the surface
with machine marks, nor a sander, which
leaves behind an abraded surface that's
smooth but without real clarity. To get
a surface that unveils the wood's figure,
its subtle depth of color, and its texture,
you have to shear the wood cleanly.
The heavy iron of a smoothing plane
provides this shearing cut as nothing else
can-leaving a surface that's smooth
and polished.
A lot of woodworkers probably think
that smooth-planing is tough work,
inefficient at best, grueling labor with
dubious reward at worst. But, in fact,
smoothing planes do their job quickly
and efficiently. In the time it takes to
change belts on your belt sander, you can
surface a few square feet of even highly
figured wood. In well-behaved wood, it
would be easy to surface a modest
tabletop in less than 10 minutes-about
as long as it takes sanding with a single
grit on a random-orbit sander. But, when
No tool can match a wel l -tuned smoothi ng pl ane for clarity, smooth
ness, and polish of the cut surface. The machi ne-pl aned surface
vi si bl e at rear mi ght appear smooth, but close inspection reveal s that
i t' s covered with a network of fi ne ri ppl es.
you are finished planing, you are done.
And, yes, you may have worked up a
sweat in the process.
There are many tools that will smooth
wood surfaces, but unfortunately no one
tool can efficiently handle all possible
situations. A well-tuned smoothing
plane comes close; it will perform much
of this work, smoothing every surface
from a large curly-maple tabletop to the
table leg. For challenging woods where
the grain is particularly prone to tearing
out or for veneered surfaces, even a
perfectly tuned smoothing plane has
limitations. In these situations, a scraper
is an alternative; it will smooth the most
difficult grain, though more slowly than
a plane. Whether held in a plane-like
body, a cabinet scraper, or by hand,
1 53
S U P E R- S U R F AC E R S
I
t's not totally correct to say that skewing is a useful
that no machine cuts a technique with a hand plane.
surface like a smoothing plane; Shearing the wood surface
there is one. Hitachi, Makita, by pushing the wood over a
and others make a machine fixed iron is not exactly a new
called a super-surfacer that idea. Coopers have been push-
cuts more like a plane than a ing barrel staves over long,
conventional rotary planer. inverted jointer planes for a
The wood is carried along on couple of hundred years or
a powered belt and forced more (see the photo on p. 21 2) .
against a heavy fixed knife that And a tool similar to the
shears the surface exactly like cooper's jointer has been used
a big inverted plane. The iron in Japan for a century to cut
is adjustable to cut on the thin, wide shavings for use as
skew-for all the same reasons wrapping paper. The physics
scrapers allow for a variable angle of
attack and a steep cutting angle. The
problem is that scrapers don't work well
in very soft woods. The best strategy is to
use both planes and scrapers to smooth
surfaces. In this chapter, I'll explain the
advantages and limitations of smoothing
planes, how to choose the right ones for
different surfaces, how to tune and
sharpen them for the best work, and how
to use them for the best results. Scrapers
are discussed at length in Chapter 9.
Smoothing Planes
of shearing the surface with a cut. A movable plate ahead of
heavy iron has been known the iron adjusts the throat-a
since the plane first appeared. fine throat for hardwoods and
In its modern, motor-driven a more open throat to reduce
form, the super-surfacer might clogging with softwoods. To
not look like a handplane, but cut the best surface the feed
in principle it works the same. rate should be high and the
On one model the iron is a iron very sharp, which really
lO-in.-Iong, 5/
1
6-in. -thick knife means surfacing only about
tipped with high-speed steel, 300 lineal feet between
bolted to a similarly shaped sharpenings. It's no wonder
knife that acts as a chip that this machine can nearly
breaker. The knife is held in a match the polished surface of
heav fixture that can be a handplane-the mechanics
rotated up to 60 to skew the of the cut are so similar.
If Icould imagine the perfect smoothing
plane, it would be only about 8 in. long,
widest at the iron and tapered at the
ends, and it would be heavy-very heavy,
as massive as if it were cast of pure lead.
The iron would be thicker and wider
than those of common bench planes,
and it would be firmly bedded against a
solid frog. What I'd really like is to be
able to adjust the iron's bedding angle,
Some of the most beauti ful and effective smoothi ng pl anes ever produced were made in Bri tai n
up unti l earl y i n thi s century. Both the A6 Norri s ( rear) and #6 Spi ers are massive, wi th thi ck
i rons and ti ght throats.
1 54 C H A P T E R E I G II T
Bai l ey-pattern smoothi ng pl anes i ncl ude the #2 and #3 (foreground) . The Bed Rocks #604 and
#604% at rear are i deal for smoothi ng al l but the most hi ghl y fi gured woods.
especially for nasty woods where a steeper
angle is more effective. My imaginary
plane would have a fine throat, so fine
that the thinnest of shavings could be
planed and not clog. So far, no such plane
exists, though some come close to my
ideal. British (Norris-type) smoothers, as
shown in the photo on the facing page,
combine the massiveness, thick iron, and
tight throat necessary for really effective
smoothing. Unfortunately, these antique
tools are so expensive and so rare that
most woodworkers will never even see
one, let alone have one to use. So most
of us have to make do with what we can
find. Fortunately, new and antique
smoothing planes are widely available
and can be easily tuned.
More so than any other class of planes,
smoothing-plane designs vary widely
from traditional wood-bodied smoothers,
to the Stanley bench planes # 1, #2, #3,
#4, and #4 Vz, to the highly evolved
designs of Norris planes. Until recently,
every furniture maker and carpenter
had at least one smoothing plane in his
tool chest, and since these planes were
often craftsman-made, it's natural that
many styles evolved due to personal
choice and regional differences. As a
result, smoothing planes differ in size,
materials, iron width, and ways they are
meant to be held. And there are other
planes, such as the longer bench planes
and low-angle block planes, which are
not even technically smoothing planes
but smooth nonetheless with good
results. Each type has advantages and
disadvantages.
CHARAC TERISTICS
OF SMOOTHING PLANES
Most smoothing planes are quite small,
commonly only from 7 in. to 10 in. long,
which is a real advantage for smoothing a
surface already flattened by longer bench
planes or machines. Smoothing planes
can also smooth surfaces that are not
absolutely flat. Their compact size makes
the plane comfortable to hold with both
hands and easy to control, and it
concentrates the forces of your upper
body, through your hands, close to the
cutting action of the iron.
Whatever their size or shape, the
best smoothing planes have one thing
in common: mass. They have a thick
massive iron, a heavy cap iron and lever
cap or wedge, and a heavy body-what
ever it takes to add weight to the plane.
Greater overall mass translates into
greater stability of the plane and better
support of the iron, which will chatter
less and give a smoother cut. A heavy
plane will also tend to maintain its
momentum through a stroke, especially
as the iron encounters contrary grain.
To imagine the difference mass can mean
to cutting quality, compare a lightweight
table saw to a much heavier cast-iron
machine. The heavy machine dampens
the cutting vibration more fully and
gives a far smoother cut. Adding blade
stabilizers improves the cut even more
and is analogous to using a thick iron in a
smoothing plane.
Plane makers have chosen many ways
to add mass to their planes to improve
performance. This partially accounts for
some of the many different plane designs
that have evolved. Traditional wood-
P L A N E S F O R S U R F A C I N G 1 55
One way that pl ane
makers add mass to
thei r smoothi ng
pl anes to i mprove
performance is to
cast them of heavy
bronze.
I n the mi d-1 920s, Stanl ey took the i dea of t hi n i rons one step further, with the devel opment of
qui ckl y repl aceabl e cutt i ng edges that i t named " ready edge" bl ades. Thi s #4 smoot hi ng pl ane
wi th "T l ever cap i s another i nnovative Stanl ey i dea.
1 56 C H A P T E R E I G I I T
bodied smoothers are made from the
heaviest and densest woods available,
such as rosewood, lignum vitae, and
ebony, which hold up well to the wear on
the sok too. For bench planes, heavier
castings add mass. The Stanley #4Yz is a
pound heavier (and an inch longer) than
the #4 and performs a lot better because
of it. At one time Stanley made a #4
1
/zH,
which was even heavier still and meant
to appeal to British craftsmen used to
the mass of Norris and similar planes.
The greater mass of longer bench planes
accounts for why they often work well
at smoothing.
Contemporary plane maker Tom
Lie-Nielsen increases the weight of his
planes by casting them of a bronze alloy
heavier than traditional cast iron (see
pp. 236-239). Heaviest of all smoothing
planes, British smoothers have a heavy
steel or cast-iron body, and the space
within it is "stuffed" or infilled with a
dense hardwood, such as rosewood,
ebony, or beech. These massive planes
are slightly smaller than a Stanley #4,
but they weigh nearly twice as much and
work a lot better, too.
The best and quickest way to add
mass and improve the performance of an
ordinary bench plane is to replace its
thin iron with a thicker one. It will
chatter less and give a smoother cut (as
explained further in Chapter 4). Old
irons on traditional planes are always
quite thick. It wasn't until the
development of the Stanley-Bailey bench
planes that thin irons became standard,
presumably because sharpening them
was easier. These thin irons are simply
too thin to resist the high stresses of
smoothing all but soft and more easily
worked woods (which the planes were
really designed for)' Under great cutting
pressure the thin iron deflects and
vibrates or chatters. No amount of
tuning or adjustment can really prevent
this problem in difficult woods.
To work efficiently, a smoothing
plane should cut a shaving nearly the
width of the iron, without chattering or
hesitating as the grain direction changes.
Only a thick iron that is well bedded
against a solid frog is able to do this.
Equally important is seating and locking
the iron securely close to the throat of
the plane where vibration originates; a
stout lever cap or wedge provides the
necessary locking force.
In all other ways, smoothing planes
are similar to other bench planes, with
the iron bedded at a common pitch of
450 Since the mechanics of the cut are
really no different from jointing or other
planing operations, this bed angle is a
good compromise. A steeper angle would
be an advantage only in very hard or
figured wood, where the iron would
begin to act more like a scraper. But this
comes at the cost of dulling the iron
more quickly and creating greater
resistance to its cutting the wood fibers.
I have a Chinese smoothing plane with a
bed angle of 580 that for many years has
been my plane of last resort when
smoothing particularly challenging
bird's-eye maple or some other densely
figured hardwood. Even if you can't
change the bed angle of your plane, you
can alter the effective cutting angle with
microbevels and back bevels, which are
explained fully in Chapter 3.
CHOOSING
THE RIGHT PLANE
Hardly a surface leaves my shop that is
not touched by a plane. Most of this
work is smoothing, for which I turn to
any of perhaps seven planes: a #4 and a
#604 Y2 bench plane, a lignum-vitae
coffin-shaped smoother, a high-angle
Chinese rosewood smoother, a low-angle
block plane, and my favorites, two Norris
rosewood and cast-steel heavyweights.
While each plane performs slightly
Tradi ti onal wood-bodied smoothers feel wonderful in your hands, are easy to tune, and can
work excepti onal l y wel l . From rear are a l i gnum-vitae, coffi n-shaped smoother; a smal l but
heavy ebony smoother; and a di sti nctive cocobol o pl ane by James Krenov.
differently-some handle difficult woods
better than others-they have all proved
to be dependable and consistent as I have
come to understand how and when to
use each of them.
No one plane is going to do it all.
Two different craftsmen could easily get
different results from the same plane
depending upon the way it is tuned,
held, and used. I recommend that you
experiment for yourself, try different
planes, and don't be discouraged if your
new Record #4 isn't the perfect
smoother you imagined-maybe it just
needs a good tuning.
Wood-bodied smoothers
Wood-bodied smoothing planes include
traditional coffin-shaped smoothers
made of hard tropical wood (lignum
vitae, rosewood, ebony), as well as
transitional planes with a wood body
(usually beech) and metal frog and iron
adjuster. Old wooden smoothers almost
always have a thick iron and cap iron that
are sometimes bedded at a steep angle
an advantage in hardwoods. The wooden
body can easily be cut to bed the iron
more completely against the frog, to add
a throat piece to tighten the throat, or to
flatten the sole. Traditional smoothers
P L A N E S F O R S U R F A C I N G 1 57
Eastern wood
smoothers are
si mpl e, low-profi l e
pl anes with t hree
basic parts: an i ron,
a sub-bl ade, and a
wooden body
( usual l y dense whi te
oak). A heavy i ron
and stabl e l ow
center of gravity
hel p them cut
smoothl y and
consi stently.
are comfortable to hold and use and
generally work well for any size surface.
To some craftsmen, nothing matches the
feel of a wooden plane planing wood.
Transitional planes closely resemble cast
iron bench planes and have the same
limitations: The iron is too thin and will
tend to chatter when overstressed, and
overall the plane is a little light.
1 58 C H A P T E R E I G H T
Eastern smoothing planes
Eastern smoothers, distant cousins of
traditional smoothing planes, have a
solid-wood body (usually white oak,
rosewood, or a similar hardwood) and
work extremely well. The iron is short,
thick, and massive; the sub-blade (or cap
iron), if there is one, wedges against the
iron rather than screwing to it (see the
plane in the foreground in the photo
above); and the throat is fine. The low
profile and lack of handles make for a
low center of gravity and wood-hugging
stability.
These planes are commonly available
with a bed angle of 40 (better for soft
woods), 45, or 47 ': (better for hard
woods) and with enough variation in size
and style to be extremely versatile in all
smoothing situations. The sole and iron
of any of these Eastern planes demand
special tuning and sharpening with
special tools-to some as much tradition
as science. Toshio Odate's lapanese
Woodworking Tools: Their Trdition, Spirit
and Use (The Taunton Press, 1984) is
an excellent source of information on
this subject.
Bench planes
All of the bench planes from # 1 through
#41/Z are called smoothing planes, but
some give better results and are easier to
use than others. The larger sizes are
widely available, either used or new. For
general bench work it is hard to beat a #4
with a thick replacement iron. It adjusts
easily, is comfortable to hold, and will
handle most well-behaved woods. A
#4Yz is more useful as a smoother,
because it is wider and heavier. It works
well for any size surface, but less so for
dificult woods. I find that the smaller
sizes are too small to smooth anything
but the smallest surfaces efficiently or to
hold comfortably for very long.
Longer bench planes, such as a #5 or
#5 Yz, are useful for special smoothing
work. I use one where I want a very flat
and smooth surface, for example, to
smooth the underside of a small case of
drawers and a desk top so that they will
mate together well. Some craftsmen
prefer to smooth with a #7, which might
not be the most eficient tool for the
work, but the large mass of the plane
helps it do a good job. The performance
of any of the bench planes can be
improved by replacing the standard thin
iron with a thicker one.
British smoothers
Undoubtedly the most handsome and
consistent in smoothing many different
woods, British smoothing planes
combine massiveness, a thick iron and
cap iron, a stout lever cap locking the
iron, and a tight throat-all of the virtues
of a good smoothing plane. Early planes
of this type had a steel sole with rose
wood or ebony infilling and no means to
adjust the iron, other than tapping it as
one would a wood-bodied plane. Norris
improved the design by adding a threaded
adjuster to control the depth and lateral
E A S T E R N P L A N E I R O N S
E
astern plane makers have
taken the idea of a heavy
plane iron one step further
than any of our Western
designs. In some of the many
variations of their smoothing
planes, a short and extremely
massive laminated iron is
secured by a sub-blade or cap
iron and solidly bedded in an
oak or hardwood plane body.
These irons are easily four or
more times thicker than a
standard Stanley bench-plane
iron and double that of the
very heavy irons of Norris
type smoothing planes.
Thickening the plane iron
is the simplest way to reduce
cutting vibration or chatter
and get a smooth finishing
cut. Similar irons are common
in other Eastern tools such
as spokeshaves, and even
their chisels have the same
distinctive short, thick form.
The short length of Eastern
plane irons is a further advan
tage when they are set into an
oak plane body quite low
compared to its width. With
the heavy iron in place, the
plane has a low center of
gravity that hugs the wood
surface. The performance of
one plane I own (shown in
the photo below) is further
enhanced by a very fine throat
formed between the iron and
a dovetailed steel insert driven
into the body just ahead of the
iron. The combination of a
heavy iron, fine throat, and a
sol id body makes this an
extremely effective plane for
all smoothing work.
An Eastern pl ane iron (foreground) is consi derabl y thi cker than a
standard Stanl ey bench-pl ane i ron.
P L A N E S F O R S U R F A C I N G 1 59
Bl ock pl anes are usef ul for smoothi ng smal l surfaces and worki ng in ti ght places. Shown here
(from top) are a Leonard Bai l ey Vi ctor #1 2Y2 wi th a decorative front and depth-adj usti ng knob
and two Engl i sh pl anes by Marpl es.
Rel i evi ng the outer
edges of a smooth
i ng plane sol e wi th
a fi ne fi l e hel ps to
prevent marri ng the
fi ni shed surface with
a sharp edge.
1 60 C H A P T E R E I G H T
alignment of the iron (see the photo on
p. 1 69). British smoothers are easy to
adjust, hold, and control for the best
smoothing work; they are ideal, except
that they are getting rare and are incredi
bly expensive. Fortunately, new Norris
type planes are available. (For more on
British smoothers, see pp. 167- 169. )
Block planes
Block planes might not be considered
smoothing planes, but they are useful for
truing small surfaces and handy for
working in tight places. I use a Sargent
# 1 31 7 with an adjustable throat and a
ball-tail handle for smoothing transitions,
such as where stile and rail meet on a
door, or for smoothing gently convex
surfaces (see the photo on p. 166).
Bedding the iron at a low angle creates a
shear cut with little resistance, but the
low angle can also become a problem
where the grain direction changes, the
iron tends to lift and tear out the fibers.
A microbevel on the iron and a very fine
throat help.
Tuning
Smoothing Planes
To do the best possible work, smoothing
planes have to be tuned carefully.
Whether they're old Stanleys or new
planes right out of the box, they all need
the same step-by-step attention. This is
the basic tuning explained and
illustrated more fully in Chapter 4.
Considering the work expected of a
smoothing plane, I am particularly
careful about flattening the sole,
adjusting the throat, and checking that
the iron is well bedded against the frog
and that the cap iron lies flat against the
iron close to the cutting edge. And just as
scrub and jointer planes have different
cutting edge profiles, smoothing planes
can have a shaped iron, too.
FLATTENING THE SOLE
To smooth well, the plane's sole must be
really flat. A plane with a distorted sole
is hard to get started smoothly in a cut,
since it will rock. The distorted sole also
makes it hard to end the cut neatly.
Through the cutting stroke, any rocking
can either disengage the iron slightly or
cause it to cut more deeply and leave a
gouged surface. The sole of most
smoothing planes is relatively small
anyway, so flattening it is no great chore.
Wooden-soled planes can be trued with
another plane, such as a jointer. Metal
soled smoothers can be lapped on a
lapping table of abrasive paper laid end
to end on a piece of plate glass or with
silicon-carbide powder and kerosene on
the same glass surface. For more
explanation of flattening the sole, refer
to pp. 5 3-57.
The flattened sole should be smooth
and polished, with no burrs that could
mar a finished wood surface. On used
planes it's common to have a few deep
scratches or other sole defects, but these
are usually of no consequence as long as
the sole is still flat and smooth. I always
finish tuning the sole of smoothing
planes by relieving all of the outer edges
with a fine file to eliminate any chance
of a sharp edge gouging the wood (see
the bottom photo on the facing page).
Lightly sanding the sole with 320-grit or
finer silicon-carbide paper brings it to a
smooth polish.
ADJUSTING
THE TH ROAT
Not all smoothers allow for throat
adjustment, but it's an area to check and
fine-tune if necessary. The throat should
be set as tight as possible-as wide as the
thickness of four sheets of office paper is
ideal for a light finish cut and slightly
wider for heavier smoothing cuts. The
throat opening noticeably affects the
These three pl anes tuned for smoothi ng have flat soles and throats to sui t the work. The
l i gnum-vitae smoother wi th an added throat pl ate ( l eft) and the #4 (center) have medi um
throats for prel i mi nary smoothi ng and general bench work. The Norris at ri ght has a very narrow
throat for the fi nest smoothi ng cuts.
plane's performance. As the chip is cut
from the surface it is forced through the
throat and curled up against the iron
bevel and cap iron. The front of the
throat acts like a fulcrum, breaking the
chip and limiting the amount of tea rout
of the fibers ahead of the cut. A tight
throat is especially important in figured
or difficult woods where, as the grain
direction changes, the plane is often
cutting against the fibers.
Using a thick replacement iron is one
way to tighten the throat and get better
performance, whether the frog is adjust
able or not. If the frog is adjustable, such
as on all of the Stanley-pattern bench
planes, moving it forward tightens the
throat. But be aware that adjusting the
frog can sometimes cause another
problem, especially on cheaper, mass
produced planes not designed to have
tight throats. If the frog is moved too far
forward, the back of the iron near the
cutting edge will be left unsupported,
rather than bedding against a beveled
portion of the sole (see the drawing on
p. 60). This allows the iron to vibrate
and chatter more easily in the cut.
You could try shimming behind the
P L A N E S F O R S U R F A C I N G 1 61
iron as described below for wooden
planes, or keep your plane for general
bench work and find a better plane to
tune as a smoother.
Adjusting the throat on wooden
smoothers is easy. The throat can be
finely tuned by adding a throat piece just
ahead of the iron, by replacing the
existing throat piece with one slightly
larger (or sliding it toward the iron as on
some contemporary European planes),
or by shimming behind the iron. Leather,
thin sheet metal, or dense cardboard all
work well as shims; just make sure to
adjust the wedge to compensate for the
added thickness. For more help with
tuning the throat, see pp. 59-62.
TUNING THE CAP
IRON AND FROG
There are two final things to check
while tuning a smoothing plane: First,
that the cap iron lies flat against the iron
close to the cutting edge, and second,
that the iron is well bedded against the
frog. Tuning both of these parts is
important to give stability to the iron
under cutting pressure, which makes
for a smoother cut.
Screwed to the iron, the cap iron adds
mass, supports the cutting edge, and
curls and breaks the chips (that's why it's
also known as a chip breaker)-three
important functions right at the heart of
the cutting action of the plane. The
better the cap iron mates with the iron,
the more help it can give. Hone the
underside of the cap iron as described on
p. 71 and set it very close to the cutting
edge (see the bottom photo on p. 72).
Similarly, bedding the iron firmly against
a solid frog will dampen out cutting
vibration more effectively. I run a fine
file over the bedding surface to leave it
smooth and flat (see pp. 5 8-59). Before
finally putting your tuned smoother to
work, hone and shape the iron.
1 62 C H A P T E R E I G H T
SHAPING THE IRON
One of the beautiful characteristics of
wood planed by hand is the subtle
surface left behind by the iron. Since the
iron of a smoothing plane can be shaped
from modestly convex to square with
relieved corners, the texture it leaves on
the wood can vary from a wave-like
pattern across the grain to a smooth,
flat surface.
How do you decide the right iron
profile? Partly it's a matter of choice. The
surface the plane cuts is one more place
the craftsman leaves behind his signature
and another element of the design. A
noticeable surface texture that enhances
the robust design and oak grain of an
Arts and Crafts chest of drawers would
be inappropriate for a Federal mahogany
side table or some other high-style piece,
where surfaces just shy of perfectly
smooth are more suitable. There are also
practical mechanical reasons for shaping
the iron. In bench planes with a thin
iron, shaping the iron will make it cut a
smaller shaving, reducing the pressure
upon it and causing it to chatter less. The
strokes will also blend together more
easily with the outer edges of the iron
out of contact with the wood.
Since a smoothing plane should be
adjusted to take a very fine shaving,
only a very slight rounding of the iron is
really necessary. When I want to leave a
surface with a subtle but noticeable
planing pattern, I shape the iron ever so
sl ightly convex by working it over the
grinder in a slight arc, grinding more
heavily on the outer edges (see p. 67).
After grinding the iron, I hone it to a
final consistent shape. I check the profile
by holding the iron against a straight
block of wood held up to the light. The
arc doesn't have to be perfect.
Shape the i ron profi l e gentl y convex or rel i eve the corners on a benchstone after gri ndi ng the
i ron. Start with a coarse stone and use l i ght pressure to prevent gougi ng the stone.
Because my preference is for a barely
noticeable planing pattern, I usually
shape my smoothing plane irons with
only slightly relieved corners (see the
photo on the facing page). Using my
benchstones, I work these edges more
heavily each time I sharpen, making sure
they are as sharp as the rest of the iron so
they don't leave dull streaks. Relieving
the corners still lets me overlap the
planing strokes and not leave a distinct
edge that would mar the smooth finish.
While planing, I check the width of the
shaving as it curls in the throat to judge
whether I need to alter the iron shape
when I resharpen, by concentrating a
little more on the middle of the iron or
on the outer edges. A shaving nearly the
full width of the throat is ideal to
smooth most efficiently.
Smoothing
Technique
To illustrate basic smoothing technique,
I'll use the example of finish-planing a
cherry dining table top. By the time I get
to this step, the top has been cut to finish
dimension and any joinery such as
breadboard ends or underside bevels has
been completed. If it was important that
the top be very flat, I would have
flattened it first with a longer bench
plane, a #5 or #6, which would likely
have left a surface with many planing
marks. There could be some grain
tearout where there is some figure in the
boards. For the final planing I start in
with my #4 smooth bench plane. This
particular plane has a thick replacement
iron with the corners only very slightly
relieved and a modest throat, since I also
use this plane for other bench work.
Holding the plane skewed to the
surface-60 or so-and taking a light
cut, I stroke down and across the top,
and, as best as I can guess, with the grain.
To smooth a large tabl etop, the author skews his smoother sl i ghtl y ( here, a #604Y2 Bed Rock)
and pl anes paral l el strokes down the l ength of the top. He keeps a t i n of paste wax handy to
l ubri cate the pl ane' s sal e.
Figuring out grain direction is not
truly a guess. Any milling or planing I
have done up to this point has given me
clues and shown me possible trouble
spots. To make the final planing easier,
when I glue up the boards I take care to
orient the grain as consistently as I can
and mark it on them (see p. 107).
Holding the plane on the skew and
working across the grain rather than
directly down it gives me some advantage
around any trouble spots and helps level
out any variation along the glue joints
(unless the table has been previously
flattened with a longer plane). Where
the grain is contrary, I try planing it from
a different direction. I work until the
surface is leveled and fairly smooth and
any tearouts are very shallow. I think of
this step as "presurfacing," before a final
smoothing with a #604 Yz Bed Rock.
A #604 Yz is an excellent smoothing
plane for better behaved woods such as
cherry. I have this plane tuned as a
smoother only: The iron is sharpened
ever so slightly convex, and the throat is
tight. This plane has two further
advantages-a well-machined frog and
impressive heft. If this was a figured
maple tabletop or some other ornery
wood, the #604 Yz might not plane it
without some tearout. It would be worth
a try, but I might have to resort to
another plane for my final smoothing
pass (such as my high-angle Chinese
smoother or one of the Norrises) or
expect to use a scraper on the areas
where there are small tea routs.
Smoothing with two planes has some
advantages. The #4 does the bulk of the
work, leveling out the surface as it
exposes fresh wood on a top that could
P L A N E S F O R S U R F A C I N G 1 63
have picked up some dirt during
construction. The #604 Vz that follows is
set very fine with an iron tuned to leave a
smooth surface with a minimum of
planing texture. Each plane is tuned for
the work it needs to do; using them
together I work more efficiently and
need to resharpen fewer times. Moreover,
the #604Vz stays sharper longer, since it
is doing only a minimum of work, and
cuts a smoother surface as a result.
With the tabletop clamped on my
bench, I plane long parallel strokes down
it with the #6041/z following the
direction of the grain (see the photo on
p. 163). The technique is similar to the
stroke with other bench planes, but
there are some subtle differences. For
one, the strokes should be as continuous
as possible from edge to edge. An
incomplete stroke leaves a spot where the
iron stopped cutting that can be seen
and felt and will need to be planed over
again or scraped out later for the
smoothest surface. If I want to avoid a
spot of irregular grain or for some reason
not complete a stroke, gliding the plane
off the surface like a plane taking off
from a runway usually works.
Unfortunately, lowering the plane into
the cut somewhere out in the surface is
more difficult to do without leaving a
few little chatter marks (because the
plane and iron don't firmly engage with
the cut right away). On really long work
this sometimes cannot be avoided, but it
is always better to start at an edge and
skew the plane to work into the surface
or any areas of difficult grain.
Getting started smoothly in the cut is
the hardest part of smoothing technique
to master. Smoothing planes are small
with a minimal amount of sole in front
of the iron to balance and guide the
plane into the cut. A distorted sole
compounds the problem by having no
fat reference to start from. I balance the
plane on the edge of the workpiece with
1 64 C H A P T E R E I G H T
the iron just ready to make contact,
concentrate my hands and thoughts, and
forcibly start in. A slight skew helps a lot
in getting started. For long surfaces I
walk right along as I plane; otherwise, I
lean forward to keep the plane engaged
with the surface.
The small size of smoothing planes is
an advantage in maneuvering across the
surface, changing the skew as necessary,
or planing around difficult grain.
Holding the plane with your hands quite
close together, the natural pressure is as
much downward as controlling direction,
which helps keep the plane on the
surface and engaged with the cut. Wood
bodied smoothers have an advantage over
bench planes in hugging the surface. It's
natural to hold them low down on the
body, since there are usually no totes or
knobs. Holding the plane in this way
lowers its center of gravity and improves
its stability and performance. Smoothing
planes such as Norrises tend to hug the
surface due to their heavy weight alone.
Each smoothing cut creates long
shavings that need to be cleared from the
throat to avoid clogging and preventing
the iron from cutting smoothly and
evenly. Equally important, clearing the
plane after each stroke will help prevent
a piece of shaving getting caught on the
back of the throat, which will mar the
surface as it gets dragged along. Lightly
waxing the sole helps, and it also makes
each stroke easier by reducing friction.
I usually have a tin of soft paste wax
and a square of flannel near at hand on
my bench just for this purpose and use
them often.
Smoothi ng a tabl e with breadboard ( or batten) ends poses a chal l enge. Pl ane up to the end,
i ncreasi ng the skew i n the di rection of the grai n of the batten as you approach i t. Just past the
j oi nt l i ne, swivel the pl ane and fi ni sh the stroke al ong the batten.
It pays to stop and sharpen the iron
regularly. How often depends a lot on
the kind of wood you are smoothing and
how perfect you want the surface to be.
Hard, figured maple will dull the
sharpest of irons far faster than
mahogany, which means you'll need to
resharpen maybe twice as often or more.
Even with soft woods like white pine
that plane easily, the iron should still be
very sharp to shear the soft fibers cleanly
rather than beating them down and
smoothing them over. As the iron loses
its sharpness it takes more effort to
push the plane (a warning sign to
notice), the surface will not have quite
the polished smoothness (another sign),
and there is a greater chance that the
iron will drive under and tear out the
grain rather than cutting the fibers
cleanly. Whenever I push to finish
smoothing a surface and avoid one last
sharpening, inevitably I get a bad grain
tea rout just as I am nearly done. I have to
resharpen and rep lane, and waste more
time than if I had just resharpened the
iron sooner in the first place.
Smoothing work has a meditative
feeling: one thoughtful stroke after
another, clearing the plane of shavings,
drawing my hand over and feeling the
surface. With light cuts, there is the
freedom to keep working until the
surface has a satisfing polished
smoothness-besides, there is too much
pleasure to hurry the work. When I am
done planing, there may still be places
where the grain refuses to plane to a
consistent smoothness, but a scraper can
handily finish the work. For this modest
tabletop it might have taken only a half
hour to plane the top and bottom to a
polished smoothness, including
sharpening. After a little bit of scraping,
if it's needed, the top is ready for a coat
of finish. Even without it, the clarity of
the surfaces shines.
SMOOTHING CROSS
GRAIN SURFACES
If this tabletop had breadboard or batten
ends (see the photo on the facing page),
smoothing it would be more challenging
and take more time. Strokes can no
longer be started straight into the
surface, because of the cross-grain bread
board secured against the long grain of
the top, nor can a stroke be ended as
easily. The same situation happens in
smoothing transitions between stiles and
rails for drawers and doors (see the
drawing below) and in many other places
on furniture. By way of example, I will
explain how I go about smoothing the
stiles and rails for a frame-and-panel
door and smoothing the joints between
them after assembly.
S moothi ng a J oi nt
Only after the joints are cut and fit
and the door is ready for assembly will
I smooth the individual parts. This
technique is no different than with the
tabletop; I use the same two planes, #4
and #604\2 bench planes, and
continuous strokes. Using a smoothing
plane with a wide iron (the #604\2 has
an iron 2Ys in. wide vs. the #4's 2-in.
iron) is a real advantage in this kind of
work, because I can smooth stiles or rails
nearly the width of the iron in one pass.
To do this, the iron should be sharpened
mostly square with slightly relieved
corners. After smoothing each part, I
mark the grain direction on it at each
joint with a tiny pencil arrow so that
when I later smooth the transition at the
joint I will be planing with the grain as
much as possible.
Skew the plane up to the joint and then
change direction, always trying to plane with
the grain on both parts.

--
- ------
Small pencil arrows
marked on the
pieces before
assembly indicate
grain direction.
Rai l
Sti l e
P L A N E S F O R S U R F A C I N G 1 65
To smooth the joint after assembly,
I use either a block plane if the variation
is slight or a larger smoothing plane such
as the #604 '.when more wood needs
to be removed. The #604 '. is tuned for
normal smoothing; the block plane has
an adjustable throat set very fine and an
iron honed with slightly relieved corners.
My hands are a little large to use the
smaller bench planes comfortably, but a
# 2 or # 3 similarly tuned would also be
a good choice. The only real trick to the
technique is to plane the joint at a skew
and work in the direction of the grain for
both parts as much as possible. Some
times this is as easy as a cou pie of skewed
passes taking off the high spots.
Where the surfaces of the rail and stile
at the joint don't align as well, I plane
the higher surface closer to level first
before trying to smooth the joint. I lower
the higher part by taking smoothing cuts
straight along the grain, starting either
from an edge or at the joint. The final
passes to smooth the joint are at a skew,
either with the same smooth plane or
more often with a block plane with the
iron set for a very fine cut. Sometimes it
is still necessary to smooth small
variations at the joint with a sharp
scraper, which is explained further in
Chapter 9.
SMOOTHING
CURVED SURFACES
Smoothing curved surfaces with a flat
soled plane might not seem possible at
first, but it can be done. Gentle convex
curves such as the apron of a demilune
table can be smoothed with a block
plane, where its small sole is easier to
balance and control than a larger
smoothing plane. Very gentle curves
can be smoothed with a #4. For curves
A bl ock pl ane works wel l for smoot hi ng convex surfaces. The tri ck is to rock the pl ane, keepi ng
i t tangenti al to the surface and fi rml y engaged so that i t cuts cont i nuousl y wi thout chatteri ng.
1 66 C H A P T E R E I G H T
both concave and convex that have a
consistent radius, a compass plane
tuned as a smoothing plane is the right
tool (see the photo at left on p. 208).
While it's harder to smooth curved
surfaces than flat ones and get as good
results, at times I have no choice. I always
try to smooth the surfaces of parts first,
before steaming or laminating them into
curves, to minimize the need for any
later smoothing. But inevitably there are
small dings, stains, glue smears, or
irregularities that will need to be planed
out of the finished curved surface.
Smoothing the surface of a convex
curve with a block plane takes a
sensitivity to the way the plane is
cutting-quite different from the force
involved with pushing a smoother across
a flat surface. The iron must be set for a
very fine cut, since the amount of the
sole contacting the curve is small and the
convex surface actually pushes into the
throat somewhat. The throat should be
very tight. The trick is to balance the
plane on the portion of the sole right
ahead of the iron, while guiding the cut
tangentially to the surface. I start at an
edge whenever possible, although this is
less critical than with flat work, and rock
the plane as I guide it over the curved
surface (see the photo at left)' Rocking
the plane toward the heel or toe either
disengages the iron from the cut entirely
or lifts the iron enough that it takes a
lighter cut. This technique is useful to
begin or end the cut where only a small
area needs smoothing, for instance,
where there is a ding in the surface. It
takes balance and control to keep cutting
a continuous shaving without chattering,
all the time conforming to either a
constant or changing curve. No matter
how carefully I try to plane the surface
smooth, I almost always still need to
scrape out small irregularities or fair the
curve slightly with a hand-held scraper.
Smoothing with a compass plane
is similar to using a #4, but more
challenging. I find a compass plane
harder to use for smoothing to a final
finish than a block plane, except where
I want to finish with a truly consistent
curve. Where two curved parts need to
mate exactly would be such a case, or
where I need to cut a consistent curve on
the inside and outside of a part. A very
slightly convex iron and a fine cut im
prove its performance. Compass planes
are discussed further in Chapter 10.
The Ultimate
Smoothing Plane
If you were to seek out one tool for the
widest range of smoothing tasks, it
would have to be a heavy British
smoother like a Norris. British smoothers
represent the highest evolution of
smoothing planes and some of the most
beautiful tools ever produced. The
combination of a very thick iron |
'
in. )
and chip breaker, bedded against a high
and solid frog, a super-fine throat, and
a massive plane body adds up to a
smoothing plane that cuts smoothly and
consistently no matter how contrary the
grain. It's not that the surface it cuts is
more perfect than that of other good
smoothing planes, but it will smooth
woods to a polish few other planes can.
Add to this the allure of brass, steel, and
rosewood in a finely made tool and it is
easy to understand why these smoothing
planes have always been sought after by
craftsmen doing first-class work in hard
and figured woods.
Although Thomas Norris is the best
known maker of these heavy smoothing
planes, he was really only one of a handful
of such plane makers working in Britain
from the middle of the 19th century up
until World War II. Stewart Spiers of Ayr,
Dovetailed.
Improved Steel Smoothing PIne.
Round Si des.
Fitted wi th rosewood and gun metal lever.
I I 2
2 !
21" clltters
W0. 9 1 K '6 1 9/

1 9.' -
1 9/6 each
Wo. 9 2 1 /- 2 l !6 /
( Patent Adjustabl e)
21 /6

Extra Cutters to ft above 1 /6 1 /6 I i8 1 / 1 0

Wo.
W0. D
Dovetailed.
Improved Steel Smoothing Plane.
Round Si cle and Closed Handl e.
Fi tted wi th rosewood and gunmetal lever.
2
2
2
t
23/-
.3/ 23/6
24/-
2./-
24/6
2-" cutters
24/- each
25/ -

( Patent Adjlstable)
Extra Cutters to fi t above f/6 1/8 1 / 1 0 2/-
No. 6, with paral lel sides, same price .as No. 5.
No. A6 "
No. A5.
(Patent Adjustable)
J
Thomas Norris and Sons of London offered over a dozen smoot hi ng pl anes, wi th different
shapes, styl es of tote, and material (steel, gunmetal , or mal l eabl e i ron) and, after 1914, with or
wi thout t hei r patented adjuster.
P L A N E S F O R S U R F A C [ N G 1 67
Early mi ter pl anes, such as thi s one by Spi ers
of Ayr, Scotl and, i nspi red the desi gn of heavy
British smoothi ng pl anes with dovetai l ed
together steel pl ates and rosewood i nfi l l .
Scotland, was building similar planes to
a superior level of craftsmanship some
20 years before Thomas Norris and Sons
of London got started (around 1 860), as
were smaller makers such as Slater of
Clerkenwell and Mathieson of Glasgow.
For the most part, these were small
family-run businesses producing a
limited number of styles and planes,
mostly by hand.
Just as common as the planes by these
makers are the individually made planes
of similar design and construction made
by the craftsman who used them. Some
were made from bought castings, others
were cast in the foundries then common
in many industries in Britain (probably
during lunch hour and using a borrowed
smoothing plane as a pattern). Irons, cap
irons, Norris patented adjusters, and
even screw caps marked "Norris London"
could be bought to complete the plane.
The evolution of the heavy smoothing
plane was a departure from the wood
bodied planes in common use. The new
smoothing planes had steel soles, to hold
up to hard wear and last longer, and,
because of their construction, far greater
mass. The design was derived both from
Roman planes with steel soles and sides
and most directly from earlier miter
planes (see the photo above). The new
design evolved to three patterns: a
rounded coffin shape similar to
traditional wood smoothers, a parallel
sided pattern, and a square-toed body
with tapering sides to the heel. Some
planes had open totes like Bailey-pattern
bench planes developed later, some had
closed totes, and some resembled the
1 68 C H A P T E R E I G H T
shape of simple wood smoothers with no
tote at all.
The design of these planes came
about in response to the need for a tool
that could handle imported tropical
woods such as rosewood and ebony that
were increasingly popular with a rich
middle class. Easily worked native woods
were also in short supply. Even though
a new heavy smoothing plane cost a
craftsman between two and three weeks'
pay, the planes were eagerly sought after
by the rising numbers of craftsman
filling the demand for the best work.
For those who couldn't afford one,
less expensive wooden planes were still
an option.
By the turn of the 20th century, the
market for the highest-quality tools was
in decline. Industrialization was so
pervasive that it was able to satisfy
everyone's demand for furniture, and
what demand there was for hand tools,
too. Hand craftsmanship was no longer
affordable, except by the wealthy.
Stanley, meanwhile, was still growing
and capturing a larger and larger share of
the world tool market with its line ofless
expensive woodworking tools.
Norris was in a special position at the
turn of the century. It was still producing
high-end planes in a wide variety of
styles-shoulder, rabbet, panel, jointer,
and miter planes-whereas the other
family businesses (such as Spiers) had
lost interest or died. Only Norris was
left making the best planes. As the
competition with cheaper Bailey bench
planes increased, Norris responded by
producing a line oflower-quality smooth
ing planes with annealed iron bodies,
stained beech in place of rosewood, and
a less precise adjuster. Although these
planes hardly compare to those of a few
decades earlier, Norris is still the best
remembered of the plane makers during
Britain's Golden Age of tools-not
because the company made the best
planes (Spiers' are every bit as good), but
in part because Norris was the last maker
of these beautiful planes.
The name Norris has become
synonymous with British smoothers for
another reason: In 1913 Norris patented
an adjuster that controlled the depth of
cut and lateral alignment. Before then,
the iron was set in the same manner as
other wooden planes, by tapping on the
iron, heel, or toe of the plane body.
Norris's adjuster is a single shaft with a
knurled knob that engages with the iron
by capturing the head of the bolt
securing the cap iron to the iron (see the
photo below). Rotating the adjuster shaft
side to side adjusts lateral alignment, and
screwing the shaft in and out on a fine
thread adjusts the depth of cut.
The adjuster was a definite improve
ment over the nonadjusting planes of
other makers. It made the plane easier to
use, even though it doesn't adjust the
iron as smoothly as you might expect for
such a fine tool. Its shortcomings are
slight; the adjuster is a little sloppy and
will not adjust smoothly if the lever cap
is tight. Yet, Norris planes sell at a
premium in large part because of the
adjuster, where similar fine planes
without one can sell for half as much.
Apart from the fine work these
smoothing planes are capable of, there is
at least one more reason to own one
they are a good investment. In this
modern age of planned obsolescence,
how many tools can you buy, use in your
work throughout your lifetime, and
every year have them grow in value?
As some of the premier antique wood
working tools, Norris smoothing planes
and those of similar makers are among
the best such investments, but they are
not easy to find and are costly when they
are. Early planes with a maker's mark are
the most valuable, especially ones with
the least amount of wear and original
irons. Users can often find planes passed
over by collectors that have or might
need minor or cosmetic repairs or a
replacement iron. There is also a wide
variety of craftsman-made unmarked
planes, mostly without adjusters, that
will give a lifetime of service. Chapter 1 3
has more to say about investing in
antique planes.
I am fortunate to own two Norris
smoothing planes and similar planes
made by the Scottish makers Spiers and
Mathieson. It's easy to appreciate the
beauty of these planes and their ability
to smooth the most ornery of woods. But
my feelings are deeper than that. More
than with any other tools I own, I feel a
connection with the craftsman who
carefully hand-built each plane as much
as 100 years ago and with the kindred
souls who have used these planes in their
craft for the many years before me.
Boldly stamped into the wooden parts
are their names: S. Simon, G. Harrison,
L. Roberts. I don't feel any need to
add mine.
Taken together, these planes inspire
a reverence I rarely feel for the mass
produced factory tools of today. They
represent the evolution of a tool that is as
functional today as when it was first
made; any further improvements would
be slight at best. Some of the tools
Stanley Rule and Level produced early in
this century, such as Bed Rock bench
planes or the #45 combination plane, are
the same sorts of tools-they simply work
well for what they were designed for.
Even though most of these tools are no
longer being made, we are fortunate that
there still are at least a few dedicated
makers of modern Norris-type planes,
trying to add their own improvements to
the originals. Whether it is a classic old
tool or a modern Norris, for serious
smoothing work there are very few tools
that are as pleasurable to use, or that
work nearly as well. You'll never regret
having one.
The Norri s adjuster
mechani sm consi sts
of a si ngl e shaft with
a knurl ed knob that
engages wi th the
iron by capturi ng
the head of the bol t
that secures the cap
i ron to the i ron.
P L A N E S F O R S U R F A C I N G 1 69
S CRAPERS
One of the most useful of hand-tools is the steel cabinet-scraper . . . . Properly
sharpened and held correctly the scraper should be capable of taking long
shavings of tissue thinness from even the most refrctory of timbers, and it
is therefore invaluable for the last fine finishing.
-Ernest Joyce, The Encclopedia of Furniture Making, 1 978
Scrapers and smoothing planes are
like a pair of workhorses; alone, each is
capable of a wide variety of work,
together, they can do much more. Some
woods are either just too wildly figured
or have a grain structure (such as roey
grain) that makes them difficult to plane
smoothly. A scraper can handle these
woods easily and leave a smooth surface.
Other woods, such as softwoods, are
difficult if not impossible to scrape, but
they can often be planed quite easily.
For smoothing any surface, there are
no better tools than a team of scraper
and plane.
Scrapers are planes, so what's so
different about them that they can curl
up shavings and leave a smooth surface
that other planes tear out? The biggest
difference is in the cutting edge of the
scraper-how it's sharpened and shaped
to cut a fine shaving when held at a high
angle to the surface. The unique cutting
edge has a tiny hook, or "burr," worked
onto it, quite different from the beveled
and honed knife-like cutting edge of a
plane iron. It's created with a burnisher
or other piece of hard steel by rubbing
along the honed edge and deforming
the metal.
Scrapers as si mpl e as they are usef ul : a European toot hi ng pl ane
(at rear) and a craftsman-made spokeshave-type scraper wi th ivory
wear plate ahead of the i ron. Two mi ni ature pl anes, one ivory the other
beech, si t atop the spokeshave-type scraper.
While it might be simple enough to
describe, creating an edge that cuts well
is probably the hardest thing to learn
about scrapers. It can be very frustrating
to feel you are doing all of the sharpening
correctly but still end up with a scraper
that works poorly. It's too bad that this
prevents many craftsmen from either
using scrapers altogether or not to their
fullest potential. Yes, there are some
tricks to sharpening and rolling the burr,
but once you learn the technique and
finally use a sharp scraper, you'll find it a
tool impossible to get along without.
1 71
Si mpl e hand-hel d
scrapers come i n a
variety of si zes and
qualities and can be
filed to any shape.
Stori ng them i n a
slotted bl ock of
wood ( or i ndi vi dual
sheaths) protects
the fine cutt i ng
edges.
Hol ders make a scraper l ess ti ri ng to use and gi ve better control . From the top, a Stanl ey # 1 2
wi th two large handl es for heavy work; a si mpl e Stanl ey #80 cabi net scraper readi l y avai l abl e
new or used; a ni ckel ed Stanl ey #81 wi th rosewood sol e; and a craftsman-made scrapi ng
spokeshave of ebony wi th brass throat pi ece.
1 72 C H A P T E R N I N E
Types of Scrapers
At first, you might not think of scrapers
as planes at all. There is no question
about some-those scrapers fixed in a
plane body that look and are used just
like smoothing planes. Another form
looks more like a heavy spokeshave;
although held differently than many
planes, these scrapers still have the plane
characteristics of soles, handles, and a
way to fix the blade. (I think of scraper
cutters as "blades" rather than irons
since they are usually thinner and of a
softer temper.)
Also included in this group are
scratch molders, profiled scraper blades
held in a stock (often wood) that helps
guide the cut. (Making and using scratch
tools is explained in Chapter 10. ) But
what about the most basic and most
useful of the scraper tools, a piece of flat
thin steel held in your hands alone? In
this case, the heel of your hands and your
fingers both guide the cut and support
the scraper just like the sole and frog of a
plane. Except for the blade, your hands
are the plane.
HAND SCRAPERS
Scrapers are ancient tools. The simplest
scraper is nothing more than a shard of
window glass or a piece of steel cut from
an old saw. Handsaw steel is perfect,
being just flexible enough and of the
right temper to be able to roll up a good
burr edge and stay sharp. Some
flexibility is desirable, so you can bend
the scraper to concentrate the cutting
force in a smaller area, say to scrape out a
scratch or imperfection. Today, modern
scrapers of this type, no longer cut from
handsaws, can be bought from any
woodworking catalog in a variety of sizes,
shapes, and qualities (such as hardness).
Most common and useful for flat
surfaces are square-edged scrapers
measuring about 3 in. by 6 in. Shaped
scrapers such as "gooseneck," concave,
and convex scrapers or ones filed to a
specific profile are useful for scraping
moldings, curved parts, or bowls.
For versatility and quick scraping jobs,
nothing beats a simple hand scraper.
I use ones of different thicknesses and
flexibilities for everything from scraping
glue or removing an old finish to
smoothing small imperfections or areas
of irregular grain on tabletops after
smooth planing. Hand scrapers have only
one unpleasant drawback; aggressive
scraping can create enough heat from the
friction to cause you to really take notice
The steel is so thin that it can heat up
quickly, right at the point where your
thumbs are making firm contact.
CA BINET SCRA PERS
The same type blade, or one slightly
thicker, can be used more easily when
held in a holder of some kind. Different
holders give different advantages, but
they all help to keep the blade oriented
to the cut, avoid the burning thumbs
problem, give an added measure of
control, and are less tiring. Holders with
a flat sole help to scrape a level plane, just
as a flat sole does on a bench plane. Any
holder helps you scrape more aggressively.
A holder can be a simple handle with
a scraper blade clamped at one end, a
tool similar to a spokeshave for light
scraping of curved surfaces, or a heavier
cast-iron holder with two handles in line
with the blade for scraping large surfaces
(see the bottom photo on the facing
page). All these designs are known as
cabinet scrapers. Not included in this
group, but as a separate scraper type, are
holders that look and work like bench
planes. Some of the simpler holders are
made of wood or have wooden soles
added to a cast-iron body for the same
reasons some craftsmen prefer wooden
A chai r devi l wi l l scrape compl ex shapes, such as the conti nuous back rail on thi s Wi ndsor
chai r, a task nearl y i mpossi bl e wi th other pl anes. The tool on the bench i s a fl at-sol ed scraper.
planes-smooth operation. The variety in
these tools is tremendolls, from the
craftsman-made scraper for a specific
job to common cast-iron cabinet scrapers
by Stanley and others. Interestingly, the
first design that Leonard Bailey patented
(in 1 855), and one of the earliest metal
planes, was a variable-pitched heavy
cabinet scraper of this type, with large
rosewood handles. Stanley eventually
produced this scraper (the # ] 2) for
nearly the next 1 00 years.
Of this second type of scraper I most
often use a Stanley #80 cabinet scraper
for leveling modest surfaces that are
difficult to plane smoothly; the flat sole
and side handles give a controlled cut
with less effort than with a hand-held
scraper. The flat sole helps me scrape out
a ding or tearout without dishing the
surface. The blade is beveled rather than
square like a hand scraper, so it is easier
to roll up a larger burr and scrape more
aggressively. It's particularly useful for
veneered surfaces, where there's just too
much risk of tearing out the thin veneer
with a smoothing plane. Although the
#80 works well on open surfaces, the
handles get in the way when working in
tight places or up against a vertical edge.
I also use a few specialty scrapers of this
type, such as a "chair devil" similar to a
spokeshave (see the photo above), for
working curved surfaces or small areas
more easily scraped than planed.
SCRA PER PLANES
A third type of scraper is the most plane
like; in fact, these tools all look like
planes. Some have the same front knob,
rear handle, flat sole, and general shape
S e R A P E R S 1 73
Si mi l ar to the bench pl anes they resembl e, scraper pl anes have fl at
sol es and strong handl es. Shown here are three rare Stanley desi gns:
from the top, a #87, a #85 wi th t i l ti ng handl es, and a #21 2 that i s used
one-handed.
Ori ental scrapi ng pl anes have thi ck i rons wedged into l ow hardwood
bodi es. The two smal l er planes are used to flatten the soles of l onger
bench pl anes.
of a cast-iron smoothing plane. Others
have similar characteristics and a rabbet
mouth and handles that tilt to one side
or the other for working in close to a
vertical surface (see the photo at left
above). Three of the rarest Stanley tools
are scraping planes: the # 1 2 Y4, #85, and
#21 2. Recently, Veritas introduced a
scraper-plane insert that fits into a cast
iron bench plane such as a #4 or #5 to
convert it to a scraping plane.
Wooden scraper planes look exactly
like bench planes with thick irons and
wedges and differ only in that the scraper
blade is set at a much higher pitch
sometimes nearly vertical (see the photo
at right above). Toothing planes are one
such type, with a finely serrated blade
like saw teeth that can scrape a surface
aggressively to create a good glue surface
1 74 C H A P T E R N I N E
when veneering or to level a highly
figured board. (For more on toothing
planes, see the sidebar on p. ] 8] J
All of the scraper planes are used like
planes, for the final level ing and
smoothing of surfaces. They are the
most comfortable to use for long periods
of scraping, and their large soles flatten a
surface accurately, just as a long bench
plane does. They use thick beveled irons,
sometimes serrated like a toothing plane,
that are better able to resist the heavy
cutting pressure and not chatter. Since
scraper planes cut slowly but carefully,
I use them to smooth large surfaces after
first doing as much as I can with a
smoothing plane. No matter what tools
I start with, I finish with a simple hand
scraper on the particularly difficult areas.
Cutting Dynamics
Whether a scraper i s held in your hands,
in a cabinet scraper, or in a plane-like
body, the way it cuts is much the same.
Scrapers have two distinct cutting
advantages that give them versatility and
the abil ity to work woods that other
planes can't. One is that the cutting
action of a scraper is like that of a high
angle plane iron, with all of the same
dynamic advantages. The other is that
the hook rolled onto the cutting edge
controls both the depth of the cut and
the size of the shaving. At best, scrapers
cut like a finely set and well-tuned plane,
curling up transparent shavings. They
can just as easily be tuned to scrape paint
and do other rough work. Even though
sharpening and shaping the edge takes
learning a specific technique, a
sharpened scraper is a tool that nearly
anyone can use with good results over a
wide range of conditions.
Using a scraper at a high angle or
pitch curls the shavings so abruptly that
tearout and splitting are less likely,
especially if the cut is light. Scrapers cut
over a range of pitches, depending upon
the size and shape of the burr, but
generally the pitch is about 60 or more
(see the drawing below). A normal
bench plane iron is closer to 45 , and
even though ] 5 might not seem like a
big difference, it actually is. The extreme
case is a scraper used without any burr
formed into the edge at all but just
sharpened and honed perfectly square
(like the traditional piece of glass). In
this case, the tool can be used almost
vertically for the finest shavings, very
light cuts, and utmost control.
The unique shape of the hooked edge
has just as much effect on how a scraper
cuts as does its pitch. The burr is rolled
onto the edge with a burnisher held
against it at anywhere from square to the
edge to about 1 5 . Burnishing different
angles creates different burr shapes. The
heavier the pressure with the burnisher,
the more the steel is deformed and the
larger the burr. Whereas a plane uses
the depth of the iron and the width of
the throat to control the size of the
shavings, the size of the burr and the
pressure upon the cutting edge do the
same for scrapers.
All of the advantages that make
scrapers well suited for working
hardwoods make them generally less
useful for softwoods. Softwood fibers are
usually more smoothly cut with an iron
at a lower pitch, because they offer less
resistance. High angles tend to lift the
soft fibers rather than cut them. While
it's not impossible to scrape pine or
basswood, for example, only a scraper
carefully sharpened with a very fine burr
will work, and even then the surface isn't
as smoothly cut as with a plane. Part of
the problem is that usual scraper
technique is to flex the blade slightly and
concentrate the cutting force along a
small area of the edge, making it even
more likely that the soft fibers will be
pressed down and deformed rather than
cut. Fortunately where scrapers are
needed most-for smoothing difficult
hardwoods-they also work the best.
Tuning Sera pers
Sharpening a scraper blade i s the most
dificult part oflearning to use scrapers,
but it's really not all that different from
sharpening a plane iron. Understanding
what the edge should look like and how a
scraper cuts helps a lot in learning to
sharpen. As with a plane iron, there are
S c r ape r Pitch and E d g e
The small burr worked onto the edge of
a scraper curls up a shaving and limits
the depth of cut.
many possible ways to create the cutting
edge, each yielding different results.
An edge suitable for smoothing inlaid
veneers is very different from one that's
best for leveling a tabletop. Ultimately,
the most satisfying results come from
trying some of the variations to create
slightly different edges and see how they
work for you.
All scraper blades are sharpened in
essentially the same way. Thin blades
have edges that are most often square
with the sides and a burr rolled to either
side; thicker blades as are common in
cabinet scrapers or scraper planes are
beveled at 45 or less with a single burr
rolled toward the back. A very fine
cutting edge can be produced with no
burr at all, but most scrapers do have a
burr of some kind. Toothing planes need
none because the serrated iron cuts well
without it. To simplify the explanation
of tuning technique, I'll focus on the
Pitch angle vares
from 60 to 90.
)
S e R A P E R S 1 75
process of tuning a scraper with square
edges. Tuning a scraper with a beveled
edge is in essence the same, with only a
few small variations in honing and in
rolling up the bevel Csee pp. 180- 1 81 ) .
JOINTING THE EDGE
Before you roll on a burr, the cutting
edge needs to be carefully honed and
prepared. You can roll up an edge on a
scraper blade without any preparation
and it will still cut, but it will not be
truly sharp, it will be finely serrated and
Worki ng at a sl i ght
skew, fi l e the edge
of a scraper square
i n a machi nist's vise
fitted with wooden
jaw protectors. Use
the bl ocks of wood
l i ke a shooti ng
board to fi l e square
to the si des and
strai ght al ong the
edge.
1 76 C H A P T E R N J N E
leave scratches on the surface, and it
will dull quickly, too. Take the same
blade and hone the sides and edge as
perfectly as a plane iron bevel and back,
and then roll up a fine burr and the
scraper will cut extremely fine shavings,
leave a polished surface, and have a much
longer lasting edge. It lasts longer because
more of the edge is working (rather than
just the tips of the serrations that break
away). The smoothly prepared edge
has one more advantage: The edge can
be quickly burnished down and rolled
up again and be nearly as sharp as it
was originally.
I start preparing the edge by filing it
square and straight. To do this I clamp
the blade lightly in a machinist's vise
(between wooden blocks is best), with
the edge I'm filing just above the jaws.
You could use a woodworking bench side
or end vise, but I prefer to keep metal
filings well away from anywhere I' m
using planes. For a file I use a very fine
lO-in.-Iongj eweler's file. It leaves a
smooth cut, but jointing with a fine mill
bastard file and stoning the edge just
slightly more will give the same results.
I file with the length of the file along the
edge, at a slight skew, and use the top of
the jaws as a reference to file straight and
very square with the sides (see the photo
at left)'
I find that it's easiest and fastest to
work freehand, but you can joint the
edge with any of a number of jigs. I have
an old commercial cast-iron saw jointer
that holds a file at right angles to a fence
that rides along the side of the scraper
(see the top left photo on the facing
page). New versions are available, too.
A simple jointing jig (see the top right
photo on the facing page) is nothing
more than a wide kerf cut in the side of a
hardwood block to fit a file snugly
(adding a screw or two in from the top
will lock it in place). Holding the side of
the block along the scraper's side and
working up and down the edge files it
square and true. Whatever method you
use, the important thing is to get a nice
square edge. I like to file a straight edge,
because it can be more quickly honed,
but a slight camber works fine, too.
Ideally, it's nice to keep the tiny
serrations left by the file parallel with
the edge for the smoothest final edge,
but with careful honing this is less
important.
An ol d cast-i ron handsaw j oi nter fitted wi th a short, fi ne fi l e works wel l
for j oi nti ng a scraper bl ade.
A si mpl e j oi nti ng tool can be made by cutti ng a sl ot i n a bl ock of hard
wood to hold a file snugly.
HONING THE EDGE
Honing technique is similar to jointing,
except that the edge of the scraper is
refined with a benchstone instead of a
file. Similar sorts of jigs and techniques
work, too. Keep one thing in mind,
though; scrapers are thin and hard
enough that they can easily wear a groove
in a soft stone (such as a waterstone).
This isn't good for your stone, nor will it
hone a square edge. If the scraper does
work into a groove, it will tend to round
the edge and negate all your efforts.
My preferred honing method is quick
and easy. Holding the scraper upright, I
work it back and forth down the length
of the stone and slowly from one side to
the other (see the photo at right). It's
something like a sawing stroke using all
of the stone. The only trick is to keep
the blade square with the stone. Nearly
as easy is to run the edge of the scraper
against the side of the stone while
supporting it flat on a block of wood
alongside. Varying the thickness of the
block will ensure working different areas
of the side of the stone. I hone until the
To hone the edge of a scraper, hol d it upri ght and "saw" on the face of the stone, worki ng back
and forth and sl owl y si de to si de to avoi d scori ng the stone.
edge appears polished and feels very
sharp. Just as important is honing the
flat sides, because, as with a plane iron,
they form half of the cutting edge. I hone
the sides flat on the face of the stone,
working one side and then the other,
shifting my fingers and the pressure
often. I finish with a few strokes with the
blade on edge to remove any wire edge.
At this point, try out your honed
scraper on a block of maple or cherry to
see what difference rolling up a burr in
S C R A P E R S 1 77
Burni shers for worki ng the bur r on the cutt i ng edge of a scraper need
to be hard and smoot h. The two shown here are made from ol d files
careful l y ground and pol i shed; the tri angul ar burni sher i s best for
strai ght edges, the oval for curves.
D r aw i ng t he Bur r
Flat bl ock
of wood
To draw out the burr and work
harden the edge, strop along
the face of the scraper near the
edge, keeping the burisher fat
against the face.
1 78 C H A P T E R N I N E
Scraper
Burni sher
Work-harden and draw the steel al ong the edge before turni ng the
burr. Lubri cate the burni sher wi th a drop or two of oi l , and work it flat
al ong the side near the edge back and forth a few ti mes.
the next step makes. As is, the edge
should turn up a nice fine shaving, but it
will cut much less aggressively and dull
more quickly than a scraper with a burr,
and you'll need to hold the tool at a high
pitch for it to cut. (If the scraper works
up a fine dust, it's not sharp and requires
further honing.) I sometimes use a
scraper without a burr with very light
pressure for careful smoothing around
inlays or at joints where the grain meets
at right angles.
ROLLING UP THE BURR
So far this sharpening technique is
straightforward and should pose no
problems to anyone familiar with
sharpening planes. What is a little tricky
though, is rolling up the burr. This is
where most of the confusion about
scrapers lies. I suspect that some of the
poor results with scrapers are due to not
preparing the edge well to begin with
and then having to use a lot of pressure
to roll up a burr. Such a burr won't last
long or cut as well as it could. Another
fault is rolling up a burr at too acute an
angle to the sides, or in other words
farther off square from the edge. This
sort of burr might actually curl so much
that the scraper practically needs to be
horizontal to cut well. By then you're
dragging your knuckles, too.
A third common fault is to roll up the
burr with the wrong tool or with
excessive pressure. The metal deforms
and tears, forming a hook useful only for
rough work. The best burr is rolled up
with light pressure at a consistent angle
with a smoothly polished burnisher. A
fine burr will cut wonderfully, it will
last just as long as a larger burr, and it
can be worked down and rolled up again
without going through the entire
resharpening process.
A burnisher is a useful woodworking
tool for a lot of tasks, but it's essential
for getting the best results with a scraper.
I have two that I made from old files by
carefully grinding off the teeth,
smoothing the edges, and polishing the
surfaces. One is softly triangular, the
other oval (see the photo at left on the
facing page). The handles are simple
hardwood turnings. The alternative is to
use the back of a chisel, gouge, or awl,
but I prefer the predictability of using a
burnisher. There are a number of
burnishers and burnishing tools
available through some of the better
woodworking catalogs meant just for
rolling the burr onto scrapers.
A burnisher works well for two
reasons: It's harder than the scraper steel
and can deform it, and it's the right
shape. Scrapers do come in a range of
hardnesses. The harder the steel, the
longer the edge lasts, but also the harder
the tool needed to roll a burr edge on it.
The burnisher's shape spreads out the
pressure against the edge, gently
deforming it, but hopefully not so much
that the burr is rough and broken. With
light pressure this is less likely to happen.
I use the triangular burnisher for straight
edges and the oval one for turning the
edge on curved scrapers, because it more
easily follows their shape.
To begin rolling the burr, support the
scraper on a flat block of wood, lubricate
it with a drop or two of oil, and strop the
sides with the burnisher (see the photo
at right on the facing page). The idea
here is to keep the burnisher flat against
the side and work back and forth a few
times on each side close to the cutting
edge. This ever so slightly {draws" the
metal that will be the burr and work
hardens the edge slightly so that the
hook lasts longer. If there is an old burr
already there, this method will roll it
down in preparation for reshaping it.
Any wire edges left over from honing
and filing are also smoothed out.
Holding the scraper in your hand, roll
up the burr by wiping the burnisher
against the edge three or four times (see
the photo above). The first stroke should
be nearly 90 to the edge, and each
successive stroke should be at a slightly
To turn the burr
al ong the edge of a
hand scraper, start
with the burni sher
square wi th the
edge, take a stroke,
l ower it a degree or
two, stroke agai n,
and stroke a thi rd
ti me, fi ni shi ng some
where between 75
and 85.
more acute angle (as shown in the
drawing on p. 1 80). The pressure should
be moderate. Slightly more pressure is
needed with the oval burnisher than
with the point of the triangular one, only
because the pressure of the triangular
one is more concentrated. The idea is to
deform the edge into the burr, but slowly
enough that the steel doesn't have
microscopic tears. Until you get a feel for
rolling up the edge an oval burnisher will
give the best results, because its
roundness shapes the metal smoothly.
Changing the angle of the strokes and
building up the burr slowly helps, too.
I repeat this process on the three
remaining sides of the scraper.
The burr on the edge should be quite
noticeable, and it should feel sharp.
The size of the burr is a function of the
pressure used and the angle the
burnisher makes with the edge. A final
angle of about 85 leaves a fine, sharp
burr. Don't use an angle any lower than
about 75 , because it will create a
cutting edge that has to be tilted well
forward to cut. Tilt the scraper to feel the
angle at which your edge cuts best.
S e R A P E R S 1 79
Rol l i n g U p the Bur r
BEVEL-EDGED SCRAPER
Using modest and
consistent pressure, wipe
the burisher along the bevel
(1) and then move it toward
the horizontal (2, 3).
To. turn the bur r
on a bevel -edged
scraper, work from
the beveled si de,
stroki ng repeatedly
with modest
pressure. Stop
with the burni sher
between 1 0 and
1 5 from square
with the edge.
1 80 C H A P T E R N I N E
2
3
SQUARE-EDGED SCRAPER
Using light, consistent
pressure, wipe the burisher
along the edge at 90 (1)
and then at progressively
lower angles (2, 3).
The greater the angle of
the last stroke, the higher
the pitch when using the
scraper.
BEVEL-EDGED
S CRAPERS
Part of the beauty of hand-held scrapers
is that the angle of attack, or pitch, can
be changed quickly and easily. The
heavier bevel-edged blades common in
cabinet scrapers and scraper planes are
adjustable over a much smaller range of
pitches, or in some cases aren't
adjustable at all. So while they are
sharpened in a similar way to the lighter
scrapers, to get the best results means a
little trial and error to get a hooked
edge that fits the tool's pitch. What this
really means is paying attention to the
angle the burnisher makes with the
cutting edge.
The preparation is very similar to the
method I have already described for
square-edged scrapers, except that the
blade is filed and honed at a bevel. Any
of these blades can be sharpened square,
with the advantage of having an extra
edge on both sides. The reason they are
beveled is so that an aggressive burr can
be rolled on more easily, in that just the
metal of the bevel needs to be deformed.
The bevel also creates an ample relief
angle. A bevel angle between 30 and
45 works fine. Sharpen the bevel the
same way as for a plane iron and relieve
the corners so there is no chance of
digging them into the finished surface.
To create the cutting edge, first work
harden the back with a few light strokes
as for a hand scraper. Use a drop or two
of oil. Then, with the burnisher resting
on the bevel, stroke along the edge. Work
lightly a few more times back and forth,
each time with the burnisher more
square with the edge (see the photo at
left). Finish with the burnisher at an
angle of between 10 and 1 5 for a burr
of the right shape and angle. Since these
blades are used for more aggressive
leveling of surfaces, I always work on a
noticeably larger burr, with an extra
stroke or two or with slightly more
pressure than on a hand scraper.
RESHARPENING
Depending on what I am doing and how
sharp I need my scraper to be, I can often
roll down the burr and reshape it at least
once. It's never as sharp the second or
third time, but it does save going
through filing and honing the edge again.
Thicker bevel-edged blades never
resharpen as successfully, because the
burr is usually larger and deforming the
metal to roll it down and back up again
tends to dull the edge considerably.
Curved scrapers are sharpened in a
similar manner. I have a large variety of
different-radius scrapers made from old
sawblades, some with beveled edges and
some without. The challenge is to hone a
sharp edge and then work the burnisher
along it at somewhat of a consistent
angle. I usually end up just sharpening
the area I happen to need, say to fit
within a cove molding. Round files and
small slipstones help to shape and hone
both inside and outside curves. I work
the burr edge on with a round burnisher
using light pressure.
To resharpen I roll the burr down
with the burnisher, in exactly the same
way I work-harden and draw the edge
originally-by stroking close to the edge
with the burnisher flat against the side.
The burr edge is then rolled up. The
T O O T H I N G P L A N E S
T
oothing planes are a
special type of scraper
plane, with a heavy, serrated
iron (much thicker than
common scraper blades)
bedded at nearly a vertical
pitch (see the photo on p. 170).
The serrations cut like the tiny
teeth of a fine handsaw scraped
across the surface. Irons vary
in coarseness, with 20 to
more than 30 teeth per inch.
Thinner toothing blades were
once available for cabinet
scrapers and scraper planes
and can sometimes be found
on the used tool market.
gave a better glue bond. With
modern glues little if any
toothing of veneers is done.
I don't use a toothing plane
much, but sometimes it's the
only tool for the job. I think of
it as the scrub plane of the
scraper family, used to level a
surface quickly no matter how
difficult the wood. It leaves a
rough surface, but one easily
smoothed with other tools.
Since the depth of the cut is
not dependent on the size of
the burr-there is none-the
iron can be set quite aggressive
ly. Sharpen and hone the bevel
like any plane iron (there's
no need to flatten the back).
lighter the burr, the more easily it can be
rolled down and back up a third time.
After that it's back to filing and repeating
the preparation, which only gets easier as
the sides hone to a smooth polish.
FINAL TUNING
Once you have a feel for rolling on the
unique burr edge, the rest of tuning
scraper tools is a snap. With a hand-held
scraper, sharpening the blade is the
complete tuning. The soles of cabinet
scrapers and scraper planes should be
lapped if they are hollow or warped,
which is not a big job considering their
size. The throat needs no attention, since
the quality of the shaving does not depend
on its size as it most definitely does in,
Originally toothing planes
had two uses: to level
particularly ornery surfaces
and to "tooth" veneers and the
grounds they are glued to. The
idea was that a rough surface
It cuts unique shavings
something between coarse
sawdust and tiny shavings.
Toothi ng bl ades, fi nely serrated l i ke saw teeth, have tradi ti onal ly
been used in scrapers for roughi ng the surfaces of the veneer and
ground for a better gl ue bond, but they are al so useful for level i ng
hi ghl y fi gured and ornery woods.
S C R A P E R S 1 8 1
say, a smoothing plane. Any handles
should be tight and comfortably shaped.
As for the bed that supports the
blade, it's much less important that it be
flat in a scraping tool than in a bench
plane. This isn't to say that a scraper
won't chatter; in fact, it will do so quite
easily. But to cut the best surface, the cut
should be light, so there is less pressure
upon the blade than there is with a
plane. There is another reason that the
bed is less important: On some scraper
holders there is a screw behind the blade
to flex it into a curve away from the bed.
Flexing the blade serves two purposes. It
directs the cutting force into a narrower
arc of the blade, and changes the depth
of the cut. The arc stiffens the blade
somewhat, too.
U sing Sera pers
There are no great differences between
how each of the three types of scraper
tools are used or for what types of
surfaces. Naturally, a cabinet scraper or a
scraper plane with a flat sole and stout
handles is easier to use for smoothing a
large surface, where the tool holds and
guides the blade. Although a hand-held
scraper leaves just as polished a surface, it
takes longer and might leave you with
hot thumbs.
I hold a hand scraper between fingers
and thumb at both ends and flex the
blade to concentrate the cut. This puts
the pressure right where it's needed, but
unfortunately also gives my thumbs
good contact with the steel right at the
point where the most heat is generated
by friction. Some craftsmen prefer using
a cabinet scraper or scraper plane just to
avoid this problem. Light pressure with a
hand scraper and pausing occasionally
works for me, or if I plan on doing a lot
1 82 C H A P T E R N I N E
of scraping I wear the leather "thumbs"
cut from an old pair of workgloves.
I use a hand scraper with long push
(and sometimes pull) strokes that glide
into and out of the cut. My palms guide
the cut, and my locked wrists keep the
pitch consistent. The beauty of scrapers
To use a hand
scraper, hol d it
between your fi ngers
and t humbs and
fl ex the bl ade for
ward into a sl i ght
arc. Ti p the bl ade i n
the di rection of the
cut, and push with
even strokes that
gl i de into and out of
the cut.
To set the cutting
depth of a cabi net
scraper, rest the
tool on a piece of
paper j ust ahead
of the throat, sl i de
the bl ade i n, and
secure i t. Turn the
t humbscrew to
tensi on the bl ade
and to i ncrease the
depth of cut.
is that they can be worked in any
direction, but they will leave the most
polished surface cutting with the grain.
Avoid pressing too hard at the start of
the cut, which can leave the surface with
tiny dents. If chatter is a problem-and it
almost never is with a hand scraper-
work the area from different angles and
try pitching the blade differently. Using
the tool upright is usually more
aggressive than tipping it forward. Try to
use the entire length of the edge before
resharpening. For working into a corner
I hold the scraper in one hand and pull it
toward me with my palm still acting as a
sole. Rarely do I sharpen the two short
edges of the scra per, so that if need be I
can use either edge to guide the cut
without cutting with it, too. Breaking
these edges with a file makes the scraper
more comfortable to hold.
On cabinet scrapers and scraper
planes the blade depth, and on some
tools the pitch, needs to be set before
using them. Adjustments are made the
same way in both tools. Initially, I set the
depth by slipping the blade into its
holder with the cabinet scraper or plane
lying sole down on the bench (as if it
were being used), with a piece of note
paper under the sole ahead of the blade
(see the bottom photo on the facing
page). The paper is just thick enough
that once the blade is secured by the
hold-down screw, it projects below the
sole about the thickness of the paper and
parallel with the sole. This might seem
like too little, but it's actually about
right. If the blade is not parallel with the
sole, adjust it by tapping it with a
wooden mallet just as if adjusting the
iron of a wooden plane. On the Stanley
#80 the depth is further adjusted by
turning the thumbscrew behind the
blade. Turning it in presses the blade
into an arc and increases the depth of
cut. If you find you need to keep
increasing the depth of the cut and the
scraper is chattering and cutting poorly,
the blade probably just needs
resharpening.
Changi ng the bl ade' s pitch in a scraper pl ane (such as the Stanl ey # 1 1 2 shown here) also
adjusts the depth of the cut. Ti ghteni ng one nut whi l e releasi ng the other tips the bl ade forward
(for a deeper cut) or backward (for a l i ghter cut).
The pitch of the blade holder is
adjusted with a threaded rod through a
post behind it and two locking nuts (see
the photo above). Since few of these tools
also have a thumbscrew for tensioning
the blade, changing the pitch is a way to
adjust the cutting depth. First set the
pitch high (60 to 80 ) and fix the blade
in the holder with a piece of paper under
the front of the sole. Refine the pitch by
loosening one nut and tightening the
other to tip the blade forward or
backward. Tipping the blade forward
deepens the cut; tipping it back lightens
the cut.
Scraper planes or cabinet scrapers are
used in the same way as hand scrapers,
with long strokes and mostly with the
grain. Sometimes it's more comfortable
to pull the scraper. The blade is held at a
consistent pitch and the sole guides the
cut, so all you need to do is supply the
power and direct the tool. While scraper
planes and cabinet scrapers are capable
of leveling large surfaces fairly quickly
(though more slowly than a plane), they
are finishing tools best for smoothing not
hogging. A small amount of hand
scraping is usually all it takes to bring the
surface to a final polish.
At least one or two members of the
scraper family should be within an arm's
reach of any bench. Whether you use
one for scraping glue or for smoothing
wild-burled veneers to a polish, no tools
have quite the range and flexibility of
scrapers. If you get frustrated trying to
get the sharpening right, burnish lightly
and keep trying. It will be worth it when
you realize how versatile and useful
scrapers are.
S C R A P E R S 1 83
PLANES F OR S H APING
A carpenter stands in need of a great variety of tools, such as saws, planes,
chisels, hammers, awls, gimlets, &c. Common workmen are obliged to find
their own tools, a set of which is worth from ten t twenty pounds, or even
more. But for diferent kinds of moldings, for beads, and fanc work, the
master carpenter supplies his men with the necessar implements.
-The Book of Trdes, or Librr of the Useful Arts, 1 807
Of the many hundreds of different
types of planes, more shape the surface
in some way than leave it a flat plane.
Whereas a few bench planes suffced the
1 8th- and 1 9th-century joiner, it took
dozens of planes to cut the moldings to
complete the interior and exterior trim
for a house. Planes shaped everything
from round-head windows, to the
moldings run on their casings, to wide
roof cornices. The tools fit the work and
changed along with the tastes and styles
that demanded them.
When molding machines came along,
and later combination planes like the
Stanley #5 5 (see the photo on the faCing
page), molding planes could have
become obsolete. Certainly demand fell
off, and eventually all the surviving
makers closed shop. Still, molding planes
are in many shops today; I use a variety in
the course of a year. Why use them, in a
modern shop equipped with shapers and
routers, or when stock moldings can be
bought at any lumberyard? The same
question could be asked about any of the
other shaping planes-panel raisers,
The Stanley #55, known as "a pl ani ng mi l l withi n i tsel f, " was the most
complete combi nati on pl ane ever sol d. It coul d cut mol di ngs, rabbets,
dadoes, tongue and grooves, beads, chamfers, and much more.
Al most 1 00 i rons of different profiles were avai l abl e.
chamfer planes, spokeshaves, and
compass planes.
With the exception of spokeshaves,
I don't use any of these shaping planes as
much as bench or joinery planes. But
even in this age of "time is money," there
are times when they are the best and
most efficient tools for the work. With
the right jigs and cutters a router or
shaper can do a lot, but making those jigs
takes time. I can take out a beading plane
and run it along the edge of three casing
boards in less time than it takes to chuck
up a router, set up a router table, make a
1 85
trial pass or two, and sand the router beads
smooth. I can cut the same bead as easily
well away from the edge-something a
router cannot do. Moreover, the plane
cut quirk (the small groove between the
bead and the flat) is finer and sharper,
the bead as smooth as if polished. Of
course, it takes a tuned plane to get such
results, but once it is tuned, I can cut
many hundred feet of moldings before at
most the iron needs a light honing.
There are also aesthetic reasons for
using planes. Machine-cut details look
like what they are-uniform and exact.
Details cut with a plane, guided by hand
and eye, have individuality. Shapes have
the slightest variation that can be seen
and felt. To me, they are more beautiful
because they aren't machine-perfect. I
want to see the work of a craftsman's
hands and sharp hand tools in my
furniture, not the product of machines.
Shaping planes offer nearly unlimited
design possibilities. In the case of
molding planes, I think of the basic
shapes as words that can be used to write
sonnets, haiku, or exclamations. These
moldings can be bolder and more shapely
than the machine-cut alternatives,
worked by cutters designed around the
limitations of grinding carbide. The
design possibilities and the ease of using
shaping planes might encourage you to
work in new ways, to shape a table edge,
or to add a curve where you might not
have. Such details are functional and
beautiful. If this isn't reason enough to
use these planes, there is one more-they
are some of the most beautiful tools of
the plane maker's art.
Hol lows and rounds came in matched pai rs,
as many as 24 di fferent si zes. They are sti l l
the most useful pl anes f or shapi ng a wi de
vari ety of mol di ng profi l es, used ei ther al one
or i n combi nati on wi th other mol di ng pl anes.
1 86 C H A P T E R T E N
Molding Planes
Molding planes are the first planes to
come to mind when you think about
shaping wood. Hollows, rounds, ogees,
reverse ogees, astragals, beads-there is
almost an endless number of shapes. A
carpenter of a hundred years ago would
S.oNDUSKY TOOL COMI'ANY'S
[:: J

*

--
t : :
I . :
`
t'.I . """ ,
Ci `
[ :
have had dozens of different profiles,
and bought new ones as moldings
changed to suit the fashion of the day.
Each is beautiful, with a shapely wedge,
a golden beech body, and decorative
chamfers run on the edges.
Most molding planes (or molding
tools, as they were first known) have a
Most mol di ng
pl anes have a
si ngl e i ron, a si mpl e
wooden wedge, a
rectangul ar body,
and a side escape
ment throat. Both
the planes shown
here cut the same
compl ex shape (a
Greci an ogee).
NEW CATAUE.
c

)


. :
'
J

\
. ''

/
single iron, bedded at a slightly higher
pitch than a bench plane. They were
designed for working straight-grained
softwoods; cabinetmaker's planes for
working hardwood need a higher pitch
still. Usually the iron is not skewed,
although this feature is more common
on English planes. Some specialty
molding planes have double irons. Most
have simple rectangular bodies, a
handhold rabbeted out of the body, and
a tapered throat cut into the side where
the shavings are ejected. Wider molding
planes, such as cornice planes, pump
planes, and other specialty planes, often
have a bench mouth similar to a jack or
try plane.
Hollows and rounds are the most
basic molding planes, and in many ways
they are still the most useful. As the
names suggest, hollows have soles that
are hollow or concave across their width;
rounds have convex soles. Once you
could buy them individually or in sets
with as many as 24 numbered pairs.
Each cuts a specific radius and an arc of
about 60. Every manufacturer had his
own numbering system, which was not
consistent throughout the trade but was
nevertheless useful as a rough way to
compare sizes. Those who couldn't
afford the luxury of all 24 pairs, or didn't
have the space to carry them, got by with
a set of 9 even- or odd-numbered pairs.
While a craftsman might be able to
buy all of the hollows and rounds, there
is no such thing as a complete set of
molding planes. Beyond the basic shapes
there's a nearly endless variety of profiles
for specific purposes. Still, looking
through makers' catalogs at the height of
molding-plane manufacture, there is
surprising uniformity in the shapes.
Hundreds of sizes and profles were
available, which could then be combined
with one another to suit a particular
need or cut larger complex moldings.
Different trades used different
shapes, sizes, and styles of molding
planes. The house carpenter and joiner
needed the greatest variety for all manner
of architectural trim; a furniture maker
needed far fewer molding planes. Ship
builders needed, among others, large
hollows known as spar planes for shaping
masts and spars. Handle makers used
simple hollowing planes called forkstaff
Thi s unusual
whal ebone mol di ng
pl ane ( a round)
was possi bl y made
aboard a whal i ng
shi p duri ng the
1 8th or earl y 1 9th
century.
Mi ni ature mol di ng
pl anes such as
thi s pai r were
craftsman-made for
some speci al work,
perhaps for mol di ng
the fi ne mul l i ons of
a fanl i ght wi ndow.
The pl anes are
mi rror i mages of
each other, or
" handed, " t o work
with the grai n i n any
di recti on.
planes to shape handles. Large-handled
rounds cut pump logs for early water
systems. Stairbuilders used wide and
often complex handrailing planes and
nosing planes for the edge of each step.
So it was with coachmaker, casemaker,
and sashmaker, all needing different
types and profiles of molding planes.
P L A N E S F O R S H A P I N G 1 87
It wasn't until about 1 800, when the
first broadsides and catalogs appeared,
that molding planes evolved to a
standard length and style. Except for
using yellow birch instead of beech, early
American planes closely followed
English patterns. With a body as long as
l OYz in. , boldly chamfered edges, and
graceful and rounded wedge finials, the
details spoke of a tool made by hand by a
craftsman proud of his work. Later
planes are not only a standard 9 Yz in.
long, but also show a gradual conformity
of details: edges broken by the barest
chamfers, rectangular proportions, and
wedge finials more elliptical and flatter.
Although still made largely by hand
(some by prison labor), machines milled
out the stock. Details were simplified,
as factories emphasized production
over quality.
The shortening of molding planes
reflects much about the evolution of
plane making. One theory is that a joiner
could fit more planes into his chest if
they were shorter. While this is no doubt
the reason that some old planes have
been trimmed shorter, a more plausible
explanation is that the expansion of
plane making gradually improved the
tools as they became more consistent.
If a slightly shorter plane worked just as
well and took less material to make, why
make it any longer than the work
demanded? And while the decorative
wedge finial and chamfers on the plane
body are handsome, in a competitive
market, why spend the extra time on
details unnecessary to the function of
the plane?
The peak of the wooden molding
plane came between 1 870 and 1 880.
Machinery was replacing hand-cut
moldings, both within individual shops
and with specialized mills cutting
nothing but stock moldings. With more
dependable and cheaper transportation,
it became economical to ship millwork
1 88 C H A P T E R T E N
over a larger area. New combination
planes such as the Stanley #45 and
later the #55 further cut into the market
for molding planes. One patent
application for a combination plane
touted all the benefits of its design and
its "special advantage for carpenters in
smaller cities, away from the planing
mills" Stanley advertised the #55 as a
"planing mill within itself," capable of
the work of literally dozens of individual
molding planes.
No commercial molding-plane
makers are working today, unless you
include the few craftsmen making a
small number of specialty planes (see
Chapter 1 2). Luckily for us, the legacy of
all those past plane makers and years of
manufacturing is a nearly endless supply
of usable and inexpensive old planes.
Pick up a few, tune them as I describe
later in this section, and try cutting some
simple moldings. You'll be surprised how
easily the planes work and how enjoyable
they can be to use.
CUTTING
SIMPLE MOLDINGS
The most useful molding planes are the
basic shapes of hollows, rounds, and
beads. A variety of sizes of these planes
will fill the molding needs of most of us.
Add a few specific profiles, such as an
ogee, scotia, or ovolo, and you have a far
wider range of choices. Each can be used
alone to cut a complete profile or in
combination with hollows, rounds, and a
rabbet plane, to cut a cove and scotia
molding, for example. Many molding
planes have an integral fence and depth
stop cut into the sole to make them
easier to use and the work more
consistent.
There is a little more to it than just
holding the plane against the guiding
edge of the work and planing away. Many
of these planes have a characteristic
known as "spring," or the angle that the
plane is held off of vertical in use. Spring
angles are different for different sole
profiles and not all molding planes need
Some mol di ng
profiles are cut at an
angl e to the sol e, or
"sprung, " for a more
consi stent throat.
Often the spri ng l i ne
i s scri bed on the
toe or heel . I n use,
the pl ane i s hel d
agai nst the edge
wi th the spri ng l i ne
verti cal .
spring, but for two reasons spring is
important. If you imagine a shaped
molding profile without spring, where
the profile is cut deepest into the sole
the throat will be quite open (since it
tapers wider). Tearout is more likely as a
result. Springing the profile places it
more horizontal with the sole with a
more consistent mouth. Since the plane
is held at the spring angle (canted away
from the edge), it has a further advantage
of making it easier to pressure the
plane evenly against the guiding edge of
the board.
It's usually easy to determine the
spring angle by looking at the heel (or
sometimes the toe) of the plane. There
you'll see the scribed profile the plane
was made to and a long spring line (see
the photo on the facing page). Hold the
plane with the spring line vertical. Rock
the plane slightly side to side and you can
feel that the shoulder of the fence also
helps hold it at the right angle. Plane
away until the profile is complete or the
depth stop prevents further cutting.
CUTTING WIDE OR
COMPLEX MOLDINGS
An 1 8th- or 19th-century joiner lucky
enough to own a large cornice plane
could cut a large and complex molding
with one plane. Since such planes were
expensive (about as much as six pairs
of hollows and rounds) and they are not
all that common today, I imagine that
most joiners owned few if any wide
cornice planes. Those successful enough
to own one used it to cut the largest
molding of the roof trim or a bold
molding at the juncture of wall and
ceiling in a formal room.
To cut the hundred or more feet of
crown molding needed for a modest
house took considerable effort. After
cutting just a few feet with such a plane,
I can understand why molding
machinery was so quickly adopted. For
A corni ce pl ane, wi th its unusual l y wi de i ron and wedge and front handl es, can cut a crown
mol di ng. The al ternative is to use a series of narrower pl anes.
one, it takes a great amount of force to
cut the full width of an iron 5 in. or so
wide. This is why some cornice planes
have a pair of handles attached to the toe
(see the photo above), so that someone
(usually an apprentice) could pull, while
the master pushed from behind and
steered. Planes without handles have a
hole for a rope, again to be pulled by
someone or possibly to be wound around
some sort of waterwheel.
Another reason cornice planes are not
easy to use is that sharpening and tuning
them is difficult. To cut well the iron of
any molding plane must follow the sole
exactly. The wider the iron and the more
shapely the sole, the harder this is.
Seasonal swelling and shrinking of the
plane stock made matters worse. As a
result, a cornice plane would have been
used for the final few passes to refine a
shape roughed out with a plow plane,
rounds, hollows, and whatever else fit
the profile.
I use essentially this technique to
make complex moldings of any width,
only without the benefit of cornice
planes. I rough out the molding with a
router, shaper, or table saw and cut it to a
final profile with basic molding planes.
For very large profiles, which are most
difficult to cut with any method,
another solution is to make the molding
up in parts. This is exactly what an
18th-century joiner would have done.
P L A N E S F O R S H A P I N G 1 89
D r af t i ng a C r own Mol d i ng
Roof boards
Rough framing
supports cmwn. \
Crown

Dimensions of
stock = 4'/i n.
by 1 % i n.
Fasci a
Soffit
After roughi ng out
the mol di ng profi l e
with a tabl e saw, the
author fai rs the
curves and bri ngs
it to fi nal shape with
mol di ng pl anes.
1 90 C H A P T E R T E N
mol di ng
X

Separate
mol di ng
Waste with saw.
The first step in cutting a large
crown molding is to draft it out full
size to establish stock dimensions
and where wood will be cut away.
I start by designing the molding to
fit the space, its height and horizontal
projection, and draft it out full scale.
As an example, let's say I am making a
4 Y2-in.-wide cornice molding for the first
element in a roof-trim soffit (as shown in
the drawing at left). Once I establish the
profile, I make a wooden pattern of it
out of thin hardwood. This pattern will
be used to trace out the profile on each
end of the stock, and later the mirror
image made from it, to check the
molding profile.
One reason stock moldings look so
flat is that they are cut into thin stock,
obviously to save money. Bolder profiles
require thicker stock, usually 6/4 or 8/4,
with the added benefit of being a more
durable molding. Using my original full
scale profile drawing, I figure the best
orientation of the stock to remove the
least amount of material. This then
establishes the stock width and the
bevels on each edge.
The first step in cutting the profile is
to mill the stock to dimension and cut
the bevels. It's important that the stock
be accurately dimensioned, because all
future cuts are parallel with one edge
or the other. I rough out the profile
with a router, shaper, or table saw. An
18th-century craftsman would have
plowed grooves to specific depths across
the profile, to guide later cuts with
hollows and rounds. The same thing can
be done with a table saw and dado head
to "waste" the entire profile. This works
fine for any molding, but it's tedious and
takes careful setup. For a 6-ft. length, it
might very well be the quickest method.
A shaper or router also takes time to set
up and often requires special fences or
jigs, but these tools have the advantage of
roughing out the profile on many feet
more completely and consistently.
Combinations of tools sometimes
work best. I often start on the table saw
cutting the flats that make the transition
between curves. Using a large cove cutter
and many passes on the shaper might be
the next step. A router is best for smaller
details. For this particular profile I use a
table saw, cutting obliquely across the
blade as for cove cutting. This method
wastes away the most material quickly.
The trick is to cut a small amount at a
time-especially for the last pass-and to
be very careful to keep all of the pieces
oriented in the same way.
With the profile roughed out, I use
planes to bring it to final shape. Start
with the largest section of the profile, in
this case the wide concave curve forming
half of the ogee form. Round planes are
the tools for this work. Since the radius
changes, a few different planes are
needed. Rarely will I have a plane that
fits the profile exactly, nor is it really
important that it does. Start with a
round with a slightly tighter radius and
plane from end to end, using the
machine marks and profile line on the
ends of the stock as a guide. Try to plane
away the machine marks (or grooves
from a dado head or plow plane)
consistently, from end to end. For the
final pass and the fairest curve, use a
round with the widest radius that fits
(see the photo on the facing pagel
A mirror image of the wooden
template comes in handy at this point.
By holding it against the profile I can see
where I need to keep planing. This is
most important where pieces are going
to be mitered together, where consistency
is necessary. Small variations down the
length of a single piece only add to the
molding's appeal. The convex part of the
profile is faired in the same way, with
hollows of various sizes or with a block
plane. On other moldings with curves
joining into flats, a rabbet plane or side
rabbet might be needed. I finish with a
shaped scraper and light sanding to fair
the molding to a smooth profile.
BEADS, REEDS,
AND FLUTES
Beads are among the simplest of molding
profiles, yet they are beautiful and
incredibly useful. They are one of the
few profiles that Shakers, known for
their simplicity of design, used
throughout their architecture and
furniture. Some beading planes cut what
The compl eted
corni ce on the
author' s shop was
made i n two pi eces
and shaped enti rel y
wi th mol di ng pl anes.
is known as a side bead: a bead cut on the
edge of a board, flush or slightly below
the surface and separated from it by a
small square-bottomed groove known as
a quirk. A center bead plane cuts a
similar bead anywhere in a surface away
from an edge. A quirk to either side
defines it. Commonly beads are semi
circular, but there are planes that cut
Bead s, Ree d s, and Flutes
SI DE BEAD CENTER BEAD
Depth stop Boxing
ui rk
Cuts a bead
along an edge.
Cuts a bead
anywhere in a
surface.
REED FLUTE
Mul ti pl e reeds Multi pl e flutes
P L A N E S F O R S H A P I N G 1 91
A complete set of hi gh-qual i ty si de bead pl anes such as thi s one by E. Preston cuts beads from
Y i n. to 1 in. wi de or larger. The l i ght-col ored wood set i nto the narrow part of the sol e that rides
i n the qui r k i s tough boxwood capabl e of hol di ng up to the wear.
pointed gothic beads or elliptical torus
beads. The shape of the quirk varies, too,
from a sharp groove to a wide bevel.
There is a third type of bead, known
as a cockbead, which is proud or above
the surface. Although there is a plane
(called a "cockbead plane") that will cut
the bead and the surface around it, for
exampk to cockbead the edges of a
drawer, it's highly unlikely you'll use
such a tool. It's far easier to cut the beads
with a side bead plane, separate them
from the stock, and let them into a
rabbet cut along the edges of the drawer.
Any of these beads can also be cut with
a scratch stock, as explained later in
this chapter.
1 92 C H A P T E R T E N
Reeds are multiple beads. Just as with
beads, they can be cut along an edge or
away from the edge. Each reed is defined
with a distinct quirk. The mirror images
of reeds are flutes, rounded grooves cut
into the surface. Both reeds and flutes
are high-style details found on table legs
and ornate columns and pilasters. Beads,
on the other hand, show up on the
simplest country furniture, as well as on
high-style Chippendale designs.
The numbering marked on the heel
of a bead plane notes the size of the bead,
usually including the quirk. But as with
rounds, hollows, and other molding
planes, dimensions are not standard. I
have a range of side beads, from 'sin. to
1 14 in. The smaller beads find the most
use, to soften an edge and give it
definition, to create a shadow line, to
hide the joint between parts, or even as a
convenient way to hide a nail-by driving
it into the quirk. I use center bead planes
far less often, partly for reasons of taste.
What they are useful for is fairing the
shape of a side bead or reed for some
reason cut against the grain and slightly
irregular because of it. Since center
bead planes have no fence, they can be
used in any direction. To cut a center
bead requires clamping or tacking on a
temporary fence.
Cuting a bead
A well-tuned side bead plane is easy to
use. The plane has a fence and a depth
stop cut into the sole, so it's just a matter
of keeping pressure on the fence and
guiding the plane evenly. I like to finish
plane the guiding edge straight and true
first and have the top surface smoothed
close to final dimension. It's also easier
and neater to bead the stock before
cutting any joints. Besides the necessary
tuning (see pp. 1 94- 1 95), three other
things help to cut a sharp bead.
One is to increase the depth of the
fence by screwing on an extra piece.
Most planes have too shallow a fence to
begin with, and what's there might be
worn. Nothing is more frustrating than
having a plane jump out of the cut and
plow a new quirk across the finished
surface of your work. The simplest of
added fences will help steady the plane,
and add greatly to your peace of mind.
The second way to improve the cut is
to chamfer the edge of the board before
cutting the bead. A light bevel is all that
is necessary; the side bead plane will cut
it away completely as it cuts the bead. As
it is, the dynamics of an iron cutting
around the two sides of a hemisphere
(the bead) is quite challenging. Along
these sides the cut is more of a scraping
action-nearly as polished a cut, but
slower than the cutting action of the rest
of the iron. The bevel helps the plane get
seated in the cut more easily and
removes some of the wood along the side
of the bead that's hardest to cut.
The third aid to cutting a sharp bead
has to do with technique-a technique
useful with any molding plane. I don't
always use this method, but it's helpful
when I need an accurate profile from
end to end. Rather than starting from
the front end and planing down the
length, start at the finishing end about a
plane's length in. Hold the plane against
the edge and cut toward the end. Back
up a little more and plane to the end
again. Keep on backing up and planing
forward. The reason this technique helps
is that more of the plane is engaged with
the cut and guiding the plane. Working
in the usual manner, the shortest and
likely most worn part of the plane, the
toe, is guiding the cut.
As with any woodworking process,
when cutting beads it's nice to have an
inch or more of extra stock on each end
to allow for slight irregularities. This is
especially true with any molding profile
mitered together or made in parts and
meant to appear continuous.
Cutting reeds and futes
Cutting a reed is quite similar to cutting
a side bead. The simplest design is a
series of reeds run along an edge. While
To cut a decorative flute, the curved stopped end i s first cut out wi th a gouge and then the fl ute
i s cut al ong penci l layout l i nes. The fl uti ng pl ane cuts strai ghter as i t cuts deeper and stops
when the depth stop cut into the sole contacts the surface.
I suppose it would be possible to cut
them with side bead and center bead
planes, ingenious reeding planes make it
far easier. The sole of the plane has two
or more round grooves (flutes) running
down the length.
There are different designs, but all
have some means to cut one or more
reeds by running the plane along an edge
or a fence and then moving the plane
over. The previously cut reed now guides
the plane to cut another parallel reed.
The difficulty is working accurately,
because slight irregularities in the first
reed affect later cuts and can be quite
noticeable.
Some fluting planes work on the same
principle of the first flute guiding the
plane to cut subsequent flutes. Other
fluting planes have arms and a fence as a
plow does, to guide the plane along an
edge as the iron cuts out in the surface.
The simplest fluting plane looks like a
round plane with depth stops to either
side of the iron.
Part of the difficulty of cutting flutes
(and sometimes reeds, too) is that they
are often stopped shy of the end of the
work. To create a place for the plane to
cut into, the rounded end of the flute
has to be cut out first with a gouge. It's
the same idea as a stopped dado or
rabbet (see p. 1 31 ). I cut the flute either
by guiding the plane against a fence or
working freehand, following pencil
layout lines (see the photo at left)'
Working freehand is actually quite easy
to do. As the plane cuts more deeply it
straightens out any wobbles. By tipping
the plane right or left I can cut more to
one side or the other to center the flute.
I continue until the plane stops cutting
or until the flute is a consistent width
and depth.
P L A N E S F O R S H A P I N G 1 93
New l i fe for two ol d si de bead pl anes. The bottom one has a new sol e,
boxi ng, and fence; the top one new boxi ng, fence, and a prof i l e
shaped wi t h a scratch stock. A frugal woodworker of a century ago
woul d have readi l y shaped an ol d pl ane to fi t hi s needs.
I n a wel l -tuned plane, the i ron shoul d exactly paral l el the shape of the
sol e (si ghti ng down from the toe).
TUNING
MOLDING PLANES
No molding profile is going to be easy
to cut without a well-tuned plane. The
tuning is not diffcult, but it can be
tedious. The sole must be straight and a
consistent profile, any boxing (the box
wood strips let into the sole) must be
complete, the wedge must be snug
enough to hold the iron tightly, and the
iron must have the same shape as the
sole and be sharp along the entire profile.
The results are worth it-a plane set and
ready to cut any number of feet of
molding and requiring only minimal
maintenance from then on.
Little can be done about a plane
twisted in some way-except to avoid
buying such a tool to begin with. The
1 94 C H A P T E R T E N
same is true with a worn sole profile.
I have sharpened up the profile with
scrapers filed to the shape, but it takes
time, and you risk opening the throat if
you cut too much. At one time a crafts
man could send back his hardest-working
molding planes to get the sole recut or a
new iron fitted. Since we can't today, buy
planes with good soles if you can.
That said, I have taken a worn plane,
cut off the sole completely, added a new
one, and shaped it (see the left photo
above). It might seem like a drastic
measure, but if the body, wedge, and
iron are good, recutting the sole is a
modest amount of work for a desirable
or needed profile. Adding a sole has the
further advantage of tightening the
throat. Be careful when picking a plane
to do this to that it's not a valuable
1 8th-century tool (the price will be a
good indicator) but a common shape
produced by the thousands. Shape the
new sole with hollows, rounds, other
molding profiles, or a scratch stock
ground to shape. (For more advice on
shaping wooden molding planes, see the
feature on Ted Ingraham in Chapter 1 2. )
Quite often an otherwise good plane
will be missing a piece of boxing. Boxing,
usually fine-grained Turkish boxwood,
was added to planes to reinforce the sole
at points of greatest wear. Some boxing
with sliding dovetails or tongues is as
complicated as any of the most complex
joinery and is obviously not easy to
repair. Stick to repairing simple strip
boxing glued into a groove cut into the
sole, the same maintenance a past
craftsman would have done. Fine boxing,
as along the quirk of bead planes, is
strongest set into the groove with the
grain oriented at an angle of about 45 to
the sole. The wear is then against both
end grain and side grain, and the boxing
will be less likely to split out. Rosewood
or any very hard and tough wood also
works well. I cut angled pieces off of a
piece of stock as thick as the groove is
wide and glue them in place one at a time.
For thicker boxing, a simple long-grain
strip set into the groove works fine. Shape
the new boxing to fit the sole profile
with other planes or a scratch stock.
Wedges rarely need much work. Since
they are small and often improperly hit
against to free the iron, they're likely
worn but usable. Make a new wedge if
necessary, using the old one as a pattern.
The wedge should hold the iron snugly
for at least the first third of the iron.
Adjust it with a block plane if necessary.
It's best if the tip has a smooth bevel to
help eject shavings from the throat.
Use shaped sl i p
stones to hone the
profi l e of a mol di ng
pl ane iron. To work
i nto di ffi cul t shapes,
reshape a sl i pstone
against a di amond
stone (shown at
far ri ght) .
The real work of tuning molding
planes is shaping the iron to match the
sole and sharpening it. This is far easier
with a simple profile like a round than
with a complex shape, even though the
process is the same. The ideal end result
is an iron that, when viewed down the
plane from the toe, exactly parallels the
sole's shape (see the photo at right on the
facing page). If you have bought wisely,
this might be as easy as honing the back
and maybe the edge slightly.
I use three methods to shape the iron.
For irons that are only slightly off, trial
and error honing off the high spots
works. For irons further out of adjust
ment, I wedge the iron in place with the
lowest point just flush with the sole.
Then, with well-oiled slipstones and
using the sole as a guide, I hone off all
the high spots until the iron's profile
exactly matches the sole's. Naturally the
iron is now very dull. Working on a
grinder with a narrow stone (often using
the corners of the stone), I grind the
bevel freehand as much as I can and
finish it with slipstones. As with any
iron, the back should be polished. The
third method works best for really
misshapen irons or where I've recut a
new sole. In this case I take the temper
out of the iron, file it to shape (using the
sole as a guide or a line scribed onto the
back of the iron), and then reharden and
temper it. This takes some skill, a
propane torch, and a pail of water.
The tricky part about sharpening the
iron once it's shaped is honing along a
profiled bevel. Various shaped slipstones
make the job easier (see the photo
below). When I need to, I custom-shape
one against a diamond stone. Pay special
attention to any parts of the iron's profile
that cut even slightly horizontal, for
example, along the two sides of a bead.
As I explained previously, the dynamics
of these cuts are partly scraping, partly
cutting. For a smooth finish, keep these
edges sharp and beveled well back.
BUYING
MOLDING PLANES
Tuning will be a lot easier if you carefully
pick the planes you buy; it's really no
different than buying other old tools.
Luckily many thousands of molding
planes survive. There are enough around
that some collectors specialize in specific
makers, or planes from a certain area, or
even certain types of molding planes
such as cornice planes. Eighteenth
century planes with clear maker's marks
command the most money, sometimes
as much as many thousands of dollars for
an individual plane. Leave these to the
collectors and historians. For a fraction
of what one of these planes costs, you
can buy all of the perfectly usable
molding planes you'll ever need.
As with other planes, there is a big
difference in the quality of the tools
available. Some planes are too worn or
P L A N E S F O R S H A P I N G 1 95
worm-eaten to use, while others look as
fresh as the day they were made. Profiles
seldom used or that passed out of
fashion can look brand new. The most
useful profiles, the ones you want, were
made by the thousands and are
inexpensive. Skip any by fancy makers
(unless you're a collector); you'll pay
extra just for the name, and the plane
won't be any better than one made by
one of the larger manufactures such as
Auburn, Ohio, or Sandusky Tool
Company. Fine English planes can often
be bought quite reasonably from dealers
more interested in American makers.
American planes with skewed irons
are not common (by contrast, English
molders with skewed irons are),
probably because of their higher cost
new-as much as a third more. They are
no harder to tune and they work better,
so I always look for them. Check that
the body and sole are true, not kinked,
twisted, or badly worn in any way. Only
a plane with an unusual profile would
be worth trying to straighten, and even
then with no guarantee of success. I
always sight down the sole looking for
irregularities. Check for missing boxing.
Some boxing can be easily replaced,
some with a lot more difficulty.
Ideally what you are looking for is a
plane that a craftsman tuned, used, and
stored away idle for all the years since.
The iron will be shaped to the sole, maybe
even sharp, too. Such a plane tunes
quickly and is worth the little more it
might cost. Take any plane apart and look
at the condition of the iron, bed, and
wedge. A little surface rust on the iron is
to be expected, just avoid one so rusty it's
pitted. An iron can be hard to replace,
but a broken or missing wedge isn't.
Chapter 13 delves further into the
subject of buying old planes, where to
find them, cleaning them to use, and
where a weakness to "buy just one more"
for use or pleasure can lead. Collect a
sampling of hollows, rounds, and side
beads first, and then add other profiles as
you find or need them. I store many of
mine in a deep drawer, just as they would
be in the bottom of a carpenter's chest
(see the photo at right on p. 255). Of ten
used profiles sit on a shelf in my tool
cabinet where I can see the shape of
each. I don't think it's important to back
the wedge off slightly before storing a
plane away. Don't drive the wedge too
snugly and the plane will be ready to go
whenever you need it.
Scratch Stocks
Scratch stocks are an alternative to
molding planes and are as versatile and
useful molding tools as you could ask for.
A scratch stock is a scraper, a piece of
steel filed and honed to some profile and
AStanl ey #66Universal beader is a good general -purpose hol der for
scratch tools. Wi th different-shaped cutters and fences it can cut a
wi de variety of mol di ng profiles, such as the tri pl e reed shown here.
A#69hand beader, shown here cutti ng doubl e reeds, is one of the
rarest Stanley tools.
1 96 C H A P T E R T E N
held in a simple wooden guide. These
tools have two advantages over molding
planes: They are quick to make to suit a
specific need, and because they are
scrapers, they work figured or hard
woods well. Their only disadvantages are
that they cut slowly and have a very short
sole to guide the cut.
Stanley made two versions of scratch
tools, the #66 Universal beader and the
#69 single-handed beader-a very rare
tool today. The #66 came with eight
cutters and two fences, for straight or
curved work; the #69 had seven cutters.
A new set of cutters can be bought for
either. A Windsor beader is another
beading or reeding tool.
The advantage of any of these tools is
the ease with which a new cutter can be
shaped, clamped in place, and put to use.
Yet, just as useful is a homemade version.
I make the cutters out of pieces of old
heavy hacksaw blades or any good steel
about as thick as a handsaw with the
same springy temper. The guide is
nothing more than an L-shaped or
rectangular scrap of hardwood, with a
slot sawn in it. The cutter is firmly held
by a couple of small bolts that clamp it in
the slot, or if it is small enough, by
friction alone. The holder is as flexible as
the work required. I have made curved
ones to bead around a round window
and straight ones for cutting along a
table edge. If you can imagine the way
the cutter should be held against the
work, making the holder is easy.
Shaping and sharpening the cutter is
not difficult either. If the steel is not too
hard, I file it to shape and hone it with
slipstones. It's not easy on the file, but it
is quick. For harder cutters, I have to
grind the profile with a narrow-faced
grindstone (shaped with a diamond
dresser, if necessary), and then hone it to
final shape. For either method, both
faces of the cutter should be stoned to a
polish. Sharpen it like a cabinet scraper
with a perfectly square edge and no burr.
To use a scratch stock, I tip it in the
direction of the cut and use the fence to
guide the tool along. Push or pull. It
should cut cleanly, curling up fine
shavings. I prefer my wooden scratch
stocks over the #66 beader because I can
rock the cutter to the optimum cutting
angle and I like the longer fence.
Working the profile on the ends of parts
is a little more difficult than with a
plane, so leave some extra stock here.
I keep cutting until the profile is
complete, or until the tool stops cutting
because the built-in depth stop in the
holder hits on the surface. No matter
how careful you are, the profile will need
a small amount of fairing with a piece of
sandpaper. When you consider what
these tools are capable of doing, it's a
small price to pay.
Two types of Wi ndsor beaders. The one at rear has a cutter wheel with
different cutter prof i l es fi l ed i nto the ci rcumference; the one i n the front
takes i ndi vi dual cutters. Both have adjustabl e fences.
Homemade scratch stocks for cutti ng detai l s such as a smal l bead
can be as si mpl e as a shaped piece of hacksaw driven into a saw kerf
in a wooden bl ock. An old marki ng gauge also works wel l .
P L A N E S F O R S H A P I N G 1 97
An earl y panel
rai si ng pl ane with
si ngl e i ron, wedged
ni cker, and open
tote. The iron is
heavily skewed to
gi ve the best fi ni sh
on end-grain bevels.
The stocky Engl i sh panel -rai si ng pl ane In the background has a rabbet mouth and a sl i di ng
fence to al l ow for cutting bevels of different wi dths. The Ameri can pl ane i n the foreground l ooks
no di fferent from a jack pl ane with a skewed i ron.
1 98 C H A P T E R T E N
Panel Raisers
With shapers and routers and a wide
variety of panel-raising bits, there are few
of us today who still use another type of
shaping plane, a panel raiser. It's a shame
really, because these are beautiful tools
and a pleasure to use. An 18th-century
joiner would have used one for cutting
raised panels for everything from
beautifully proportioned wainscoting to
doors and the deep jambs of splayed
windows.
A raised or fielded panel is a harmony
of beauty and function. By cutting a
beveled edge all the way around the
panel, the center section is left
prominent and fielded or raised. By
beveling the edges, the panel fits neatly
into grooves run on the stiles and rails.
For strength, most of the panel is still
full thickness. Most important, the panel
can shrink or swell with the seasons, yet
it's firmly held and it gives rigidity to the
overall structure of stiles and rails. Used
for doors and paneling, raised panels
have a function and beauty that is
unsurpassed.
Panel-raisi ng planes look like jack
planes with a heavily skewed iron (to
work the end-grain edges of the panel
more smoothly), a tote, an integral fence
and depth stop cut into the sole, and
usually a single nicker. English planes are
shorter and more massive, with a sliding
fence attached to the sole (see the
bottom photo at left). This feature allows
them to cut bevels of various widths,
whereas American planes cut a specific
width. Both planes are a variation of the
rabbet plane, in that the iron extends to
an edge of the sole to cut the shoulder of
the panel.
Since panel raisers cut relative to the
face of the board, the same plane can be
used to field panels on boards of
different thicknesses. Those with a
pronounced wedge-shaped body cross
section cut without spring, others cut
perpendicular to the bevel. An
interesting feature of both is that they
don't cut a square shoulder on the bevel,
but a greater angle. Although a slight
fillet or angle here is attractive, the main
reason is that the same plane can field
panels in thin or thick stock and not
undercut the shoulder, which would
look awkward. The soles on some of
these planes are also convex or shaped so
that the bevel is cut a more uniform
thickness where it slides into the groove.
Both features show the ingenuity of the
1 8th-century cabinetmaker trying to
make his tools and efforts more efficient.
Panel-raising planes are tuned like
any bench plane, with the addition of a
nicker to sharpen. The leading edge of
the iron that cuts the shoulder has to be
beveled back and sharpened, and set
slightly proud of the side, just like a
skewed rabbet plane (see p. 1 27). I relieve
this corner of the iron ever so slightly.
To raise a panel, first dimension the
stock and smooth-plane the surface.
Then with a marking gauge set to the
groove width and using the back as a
reference surface, scribe around all four
edges. This line defines a depth to cut
the bevels to. Cut the end-grain bevels
first, so that any tearout can be planed
out when working the long-grain bevels.
Tap the nicker down so that it just scores
the fibers, hold the plane tight to the
guiding edge, and plane along. Take the
last few passes with a very l ight cut for
the smoothest finish. Cut the long-grain
bevels the same way, without the nicker.
I finish by using a block plane at the
corners to fine-tune a sharp miter
between bevels.
Chamfer Planes
Chamfers can be a detail hardly noticed
or an obvious design feature. Certainly a
wide stopped chamfer with decorative
lamb's-tongue transitions doesn't go
unseen, nor does one inlaid or fluted.
But a fine chamfer run on the edge of a
table apron blends in with the play of
light, shadows, and wood grain. Run
your hand or knee against the same edge
without a chamfer, and it will be sharp
Chamfe r s
FLAT CHAMFER
STOPPED CHAMFERS
FANCY CHAMFERS
. . Quarter-round
.. chamfer (convex
or concave)
and uncomfortable. Just the slightest
chamfer softens and protects the edge.
The simplest chamfer is a small bevel
cut into the edge, usually at 45 . When
it runs from end to end, a bench plane
can cut it as well as any tool. While not
strictly a chamfer, a slightly rounded
arris cut with a roundover plane is
beautiful and just as functional. The
most elaborate chamfers are wide, some
times even with details such as flutes or
reeds cut into the surface. Any chamfers
Pl ai n stopped chamfer
Curved stopped
chamfer
P L A N E S F O R S H A P J N G 1 99
The author' s hand
becomes a j i g to
support and ori ent
the pl ane when
cutti ng a consi stent
chamfer al ong a
tabl e edge.
Chamfer pl anes have a sol e i n the shape of a deep r i ght-angl ed "V" to gui de the pl ane al ong
a square edge. I n the background i s a Stanl ey #72, behi nd it a separate front pi ece that hol ds
scratch cutters for detai l i ng wi de chamfers. The Japanese chamfer pl ane i n the foreground has
an adjustabl e-wi dth sole and a sl i di ng carri age for the i ron.
200 C H A P T E R T E N
can be stopped or ended, with any
number of decorative transitions at the
ends. A chisel and block plane will cut
any of these chamfers, but a chamfer
plane makes accurate work easier.
I cut chamfers on many edges of my
furniture, even if they are out of view
the inside edge of a rail that a hand will
touch when lifting the piece, every edge
of a drawer or door. Chamfers blunt the
edge, for comfort and to prevent chipping,
and to show wear less. I chamfer the
edges of panels or tenons to ease fitting
the parts together.
The simplest chamfer, a small bevel,
requires nothing more than a sharp
plane and careful control. If ! am
relieving the edge of a drawer side, I hold
a block plane at a skew at about 45 to
the edge and plane from end to end. I use
a roundover plane in the same situation.
To cut the same chamfer on the edge of a
table or around a frame is another story.
For this I want a very consistent bevel.
I use my hands as a jig to orient the plane
to the edge (as shown in the top photo
at left), or I use a chamfer plane or
chamfer shave.
All chamfer planes have the same
unusual feature of a sole in the shape of
a deep right-angled "Y" to guide the
plane along a square edge. The iron is
adjustable in different ways to cut a wide
or narrow chamfer. In the Stanley # 7 2,
the iron is held in a separate front that's
movable up or down to adjust the
width of the chamfer. In English planes,
the whole center section of the plane
with iron, wedge, and throat moves up
or down. In the case of Japanese
chamfer planes and the Stanley #65
chamfer spokeshave, the iron doesn't
move, but the Y-sole opens or closes to
cut chamfers of various widths. The
Japanese tool has one further refinement:
The iron is held in a "carriage" that slides
across the plane to allow using the full
width of the iron before resharpening.
Any of these chamfer planes work
best for cutting long consistent chamfers,
for example, on the posts of a pencil-post
bed. Even if you have never seen or made
such a form, imagine cutting four equal
chamfers on a tapering square. It's
possible with a jack plane-you'll still
need to use one to fair the chamfers
end to end-but easier with a chamfer
plane. Layout is easier, because only the
ends need to be marked, and the
chamfers are accurately beveled at 45
across the corner.
For the sake of simplicity, let's assume
that the chamfers do not stop at the bed
rail as they usually would, and save the
explanation of stopped chamfers for a
moment. I first cut the bulk of the waste
with a coarsely set jack plane. Then, with
the chamfer plane set to the width of the
chamfer at the top of the post, I true up
all four chamfers (see the bottom photo
at right). If the chamfers weren't tapered,
I could complete them with this setting
of the plane. Since they are, I reset the
plane and cut the last foot of the bigger
end to final depth. For long posts I work
another section in the middle, and for
that matter could keep working sections
up the post. It's quicker to complete a
few sections and fair the whole chamfer
with a long bench plane, using the
completed chamfers as a guide.
A stopped chamfer is a little fussier.
I lay out the stop and chisel the waste
close to the final depth for at least a few
inches. This creates a place for the toe of
the plane. For the # 72 there's a bullnose
front just for working tight into the stop.
Since I don't have this part Cit's very
scarce), I use a chisel plane or even a wide
chisel. But before cutting the chamfer to
In the stop chamfer pl ane by Joseph Lee ( 1 883) at left, hal f the sol e sl i des open or closes
to adjust the wi dth of the chamfer. In the E. Preston chamfer plane at ri ght, the whol e center
secti on of sol e, i ron, wedge, and throat moves to cut wi de or narrow chamfers.
Shapi ng wi de
chamfers on a bed
post i s rel ati vely
easy with a Stanley
#72 chamfer pl ane.
The author roughs
them out with a
bench pl ane, sets
the depth of the
#72, and pl anes
each chamfer.
P L A N E S F O R S H A P I N G 201
final dimension, I shape the transition at
the stop-a lamb's-tongue or a curved
stopped chamfer-so that if I happen to
cut into the chamfer I can clean it off
with a final plane pass. One of the
advantages of the chamfering spokeshave
is that it's easy to cut a sweeping end to
the chamfer, since the sole is short and
curved. This is a nice detail for the
underside of large floor-joist timbers
exposed in the ceiling below.
There is one more nice feature about
the # 72 chamfer plane; it has a separate
front that fits scratch cutters (see the
bottom photo on p. 200). This opens up
a lot of design possibilities, such as reeds,
flutes, or inlay lines cut into the chamfer
bevel. The plane is heavy, stable, and far
easier to use in this situation than a
wooden scratch stock.
Combination Planes
I f I were to offer you one plane that
could do all the work of the various
shaping planes, and cut rabbets, dadoes,
and grooves too, wouldn't you be
interested? No longer would you have to
lug a chest full of wooden molding
planes to the job (not that you do now),
but a single modest wooden box
containing a plane and an array of
interchangeable irons. This was one of
the appeals of the combination plane, a
single plane combining the work of
many. In its highest evolution, the
Stanley #55 was said to be able to do the
work of 93 different planes
The idea wasn't exactly new. The
earliest combination planes, from
sometime back in the 16th century,
were wooden plows with interchange
able irons for plowing grooves and
cutting rabbets. Right through the mid-
202 C H A P T E R T E N
1 9th century some clever minds were
still trying to improve the wooden plow,
while others were taken by the idea of a
cast-metal plane to replace it. It was no
different than efforts to develop
practical and economical cast-iron bench
planes. In 1 844, Elihu Dutcher of
Pownal, Vermont, came up with the first
cast-iron plow, which naturally
resembled its wooden relative. Others
followed over the next 50 or so years,
each with their own improvements and
capable of more and more of the work of
other planes-plows, fillisters, beading,
and matching planes.
"Among the many advantages
afforded by making these tools of metal
instead of wood are the following: They
are much less cumbersome, are more
durable, the parts are much more readily
and perfectly adjusted, they work better
and easier, because they never choke or
clog with shavings, and they can be sold
for less than one-half the cost of wooden
planes of the same variety." Despite this
sales pitch in one patent application,
some of the early combination planes
were cumbersome. Fale's patent plane of
1 885 required two soles for every cutter
profile, plus all the cutters and main
Wi th a combi nati on pl ane, one tool coul d do the work of many. To work as a hol low, round,
or nosi ng tool (for the front edges of stairs and wi ndow si l l s) , t he Stanley #45 needed speci al
bottoms, whi ch were sol d separatel y.
stock. Even though it weighed almost
20 lb., it was still advertised as requiring
"but small space in [ al carpenter's chest."
What was appealing was a metal tool not
prone to the swelling, shrinking, or
warping of wooden molding planes, and
taking one plane on the job not dozens.
As would be expected, Stanley
developed a number of combination
planes. The two most famous are the
#45, introduced in 1 884 (see the photo
above), and the even more sophisticated
#55, introduced in 1897 (see the photo
on p. 184). Although by no means
simple, the appeal of the #45 is its
simplicity and utility compared with the
#55. Many are still in use in shops
around the world. The #55 is appealing
for what it was, for what it could do,
more than for what it actually did. It's an
amazing tool, easily one of the highest
achievements of a plane maker's clever
ness, but it's not easy to use. Others
must have agreed; few #55s show much
wear-it's common to find a box of
cutters never touched to a stone. Still,
plenty were sold, just like fancy plows
and other status tools.
With an adjustable
fence, a Stanl ey #45
combi nati on pl ane
easi l y cuts a center
bead (or, wi th
multi pl e passes,
reeds). The wooden
center bead pl ane
i n the background
requi res setti ng a
gui di ng fence for
each bead or reed.
Combination planes appealed to
our predecessors in the same way that
Shopsmiths do to some of us today. It's
the same idea, a basic tool with a whole
range of interchangeable cutters and
functions. But like any tool that tries to
do everything, it ends up doing few
things really well. Take, for example,
setting up a #45 to cut a side bead. In
the few minutes it takes to adjust every
thing-the fence, the depth of the cutter,
the distance between the main stock
and sliding section, the alignment of
P L A N E S F O R S H A P [ N G 203
Three wooden
versions of a very
useful shapi ng tool .
At top, a shapel y
beech spokeshave,
the square tangs of
the i ron si mpl y
dri l l ed i nto the body
to hol d i t; mi ddl e, a
Stanl ey #85 box
wood razor-edge
spokeshave; and,
bottom, an owner
made si mpl e spoke
shave showi ng
typi cal wear ahead
of the mouth.
A strongly curved
shave, cal l ed a
travi sher by some,
i s one of the tool s
used for shapi ng
the concave sol i d
pl ank seat of a chai r
such as a Wi ndsor.
everything, and a trial pass to check the
settings-I could run 10 ft. of the same
bead with a wooden plane. Moreover,
because I work more often with hard
woods than straight-grained pine, the
bead produced by a molding plane is
more polished and the edges of the quirk
are smoother. The entire sole of the
wooden plane conforms to the shape of
204 C H A P T E R T E N
the bead and guides the cut, while the
modest throat helps to cut cleanly.
Neither the #45 nor #55 has a throat;
only two narrow runners guide the cut.
There are some things the #45 and
#55 can do well, such as cutting center
beads, flutes, and reeds easily (see the
photo on p. 203). Since the iron doesn't
have to conform to any sole profile (as
in a molding plane), sharpening it is
easier. And for when a special shape is
needed, it's simple enough to grind an
iron and go right to work. Still, even if
we owned one, I doubt many of us
would use a combination plane much,
considering all of the alternatives.
Spokeshaves
As the name suggests, spokeshaves were
once used to shape the spokes of wheels.
Whether some still are or not, furniture
makers, carpenters, and others have
gladly adopted these useful shaping
tools. I think of spokeshaves as small
planes held by shapely handles in line
with the edge of the iron. The handles
afford a lot of control of the tool, rocking
it to conform to the shape of a curve and
regulating the cutting depth.
As would be expected with a tool that
found use in many trades, there is wide
variety among the styles of spokeshaves,
their sizes, and the shapes of the handles
and soles. The simplest ones are wood,
usually beech, or for better ones boxwood
or a hard tropical wood (see the top
photo at left)' The iron is thin and knife
shaped, similar to a miniature drawknife,
from 1 'zin. to 5 in. long. The ends of
the iron are forged into square tangs and
bent at right angles to the cutting edge.
The tangs are held in place by friction in
holes drilled through the body, and the
iron is adjusted by tapping it or the
tangs-a simple but workable arrange
ment. Better wooden versions have
threaded tangs and thumbscrews for
adjustment, and bone or brass wear
plates let into the sole ahead of the
throat. Most wooden handles are straight
and gracefully shaped. Some, called
travishers, are almost semicircular, to
work the hollowed plank seats of chairs
(see the bottom photo at left).
Cast iron opened up a whole range
of new designs. Stanley made at least 20
different spokeshaves; other toolmakers
made many more. Cast-iron spokeshaves
look more like planes, with short flat
irons and a cap iron of sorts that clamps
the iron against the bed much like one
on a block plane. Handles range from
straight to gracefully up-curved. The
greatest variation is in the shape of the
soles: straight, concave, convex, and
rounded. Each style works a particular
shaped curve most easily.
Spokeshaves can be found everywhere
at flea markets and sales. They're cheap,
because so many lack maker's marks that
they don't seem to be that collectible.
The most common shape has a short flat
sole, but there are always other shapes in
any miscellaneous box lot of tools. Look
for a variety of shapes, even if you don't
happen to shape a lot of curves; you'll
find a use for them. And even if a shave
is a little rusty, tuning it is quick.

J
BAILEY'S I RON SPOKE SHAVES.
No. GO. No. 020.
Double Iron, Handle. Double Irn, Straight Handle.
Cutter 2> inehel, price, each, cent. Cutter :;i inch. price, cent.
AdjustableRaised Hadle.
AdjustbleSlr3ght
STEARNS' IRON SPOKE SHAVES.
No. :0. Dble Cuttr, I

Cutter :Ji inches,

Cutter indes, Adjust.1.hle Cap al Throat, pe,
GOODELL'S SPOKE SHAVE.
The circular shape hitool it towork in mae

irces thaOllwr
Shave. The angle of the knife is SlIch that it instead of of the
wood Either blade can be removed to in n'ampcd places.
<'"'nlS.

Cast iron al l owed
many new spoke
shave desi gns, with
graceful l y shaped
handl es and l ong
wearing sol es.
These three spokeshaves are typi cal of the desi gns by Engl i sh maker
E. Preston, with ornate casti ngs and comfortabl e and decorati ve
handl es, and made to ti ght manufacturi ng tol erances.
Ti ny patternmaker' s or model maker' s spokeshaves cast i n brass are
useful for fi ne work. With t hree di fferent sol e shapes-flat, concave,
and convex-thi s set can cut a variety of shapes.
P L A N E S F O R S H A P I N G 205
Many curves of di fferent radi us can be cut with these three spokeshaves: a Stanl ey #54 (at work),
a cast-i ron Mi l l ers Falls #1 ( l eft foreground) , and a rosewood and brass shave ( ri ght foreground) .
The #54 has the handy feature of an adjustabl e throat that al so changes the i ron' s cutt i ng depth.
There are only three things to be
concerned with in tuning a spokeshave:
the iron, the cap iron, and the sole.
Sharpen the iron as for a plane, at a bevel
of about 25 or slightly less, and polish
the back. It can be a little challenging
grinding and honing such a small iron.
One trick is to make a holder by cutting a
saw kerf in the end of a hardwood block;
then slip the iron into it, and either
clamp or wedge it in place. A wooden
clamp alone works well, too. Irons
curved across their width for concave or
convex shaves (for shaping round
206 C H A P T E R T E N
handles, for instance) are most difficult
to sharpen. I sharpen them with slip
stones as I would a molding-plane iron.
Hone the bottom of the cap iron and
polish and wax its top surface. As for the
sole, lap it on a benchstone or lapping
table, or shape it with a fine file. Except
for flat-soled spokeshaves, it's less
important than with a plane that the sole
be perfect. The sole still guides the cut,
but so does the way you hold and orient
the tool to the work.
Setting the depth of the iron can be
tricky. English makers Record and
Preston made designs with adjustable
irons, through one or two screws behind
the iron and engaged with it.
Unfortunately, I've never cared for the
feel of my adjustable Record shave, so
I've had to set my nonadjustable ones by
trial and error. I start with the iron barely
proud of the sole, tighten the cap screw
just snug, and then, with the handle of a
chisel, lightly tap the iron to a depth that
cuts well. Trying any shave on a scrap is
the best way to see how it cuts, but
especially ones with shaped soles that are
hard to set by feel alone. For spokeshaves
tuned for finish cuts, I set the iron
parallel with the sole. For rough-cutting
shaves, I keep one corner lower so as to
have a variety of cutting depths.
I have about eight spokeshaves. Each
works well for different shapes. My
favorite is a Stanley #54 (shown in the
photo at left), with the sole ahead of the
iron adjustable by a thumbscrew, to
tighten the throat and regulate the depth
of cut. If you were to have only one
spokeshave, this would be a good choice.
Then I have a range of straight, rounded,
and concave-soled shaves. All of these are
useful for curves of not too tight a radius.
If the curve is too tight, the sole can't
contact the wood and the spokeshave
doesn't cut. For tight curves, say for a
decoratively scalloped apron, I have two
shaves almost round in cross section, one
by Millers Falls and the other by
Cincinnati Tool. Look for either of these.
The irons are so round that both are a
little tricky to sharpen, and they are not
the easiest to use, but they will cut a
tight radius that no other shave will.
Shaping curved parts can be
challenging, because the grain is change
able. Use the spokeshave as you would a
plane, as much with the grain as you can
and at a slight skew if it feels comfortable
and works. Since most of my shaves have
a modest throat, a skew usually helps get
a smoother finish. Where skewing
distorts the cut, I slide the tool to the
right or left as I cut, which gives the same
sort of slicing cut as skewing. I usually
start with a light cut to get a feel for the
way the wood responds to the tool. Two
things control the cut: the depth of the
iron and the way you orient the tool.
Since the sole is so short, it's easy to rock
the tool forward to cut a little more
deeply or backward to lighten the cut.
Using a spokeshave isn't difficult, but
when you think about rocking the tool
while also following a curve, you can see
it might take a little time to develop a
feel for it.
Compass Planes
Whereas spokeshaves cut a wide variety
of shapes, compass planes have their
usefulness shaping curved work. Wooden
compass planes look like coffin-shaped
smoothing planes with a sweeping
convex sole (not a consistent arc, though),
and they work like bench planes. Some
have the clever addition of an adjustable
toe piece that has the effect of changing
the radius of the sole to cut a wider range
of curves. Metal versions show the same
ingenuity of a whole range of plane
Most wooden
compass pl anes
have convex soles,
though they are not
a consistent radi us
down thei r l ength.
The pl ane i n the
background i s one
of a set of t hree
ebony compass
pl anes, all with
different sole curva
tures. The pl ane i n
the foreground has
an adjustabl e toe
piece for changi ng
t he effective radi us
of the sol e.
designs only possible out of this material.
The two types Stanley made, the # 1 1 3
and # 20, can cut both convex and
concave surfaces. The sole is a band of
flexible steel, pushed or pulled into a
radius through a large screw (see the
photos on p. 208). All of the cutting
parts and frog are similar to ones in a
bench plane.
Partly because I have found them
frustrating to use and partly out of the
nature of my designs, I don't use a
compass plane much. A wheelwright
P L A N E S F O R S H A P I N G 207
Two versi ons of Stanl ey's # 1 1 3 compass pl ane. By turni ng the l arge
knob, the flexi bl e steel sol e i s pushed or pul l ed i nto a convex or
concave ci rcul ar radi us.
The Stanl ey #20 works wel l for fai ri ng the outsi de curve of a tabl etop
as long as i t's the arc of a circle. Varyi ng curves are better shaped
wi th spokeshaves.
shaping the felloes making up a wheel
or a carpenter making curved head
windows and doors would find one very
useful. Both of these uses point out
their main advantages over a spokeshave:
They can take heavy cuts and cut to a
consistent radius. Since the most consis
tent radius is an arc of a circle, this is
what the Stanley compass planes cut
best. Wooden compass planes can fair a
concave elliptical curve, but they're
frustrating to use, too.
Both planes clog far more quickly
than I would like. Part of the reason is
the dynamics of cutting a curve. Take the
case of cutting a convex shape with the
#20, perhaps the edge of a demilune
tabletop (see the photo at right above).
208 C H A P T E R T E N
Until the sole solidly guides the cut,
some of the time the plane is going to
be supported at the mouth, taking too
big a bite and clogging. As the curve is
faired, more of the sole supports the cut
and the plane cuts more consistently.
The trick is to creep up on the final curve
by starting with a tighter sole radius.
Keep the cut light and slowly adjust the
plane to widen the curvature to the final
arc. Fairing a concave shape is similarly
tricky. Either technique works best if the
curve is the arc of a circle. Compounding
the problem with a wooden compass
plane is that, in order to cut a tighter
radius, the iron must be driven further
out, leading to more tearout.
If compass planes can be some of the
more frustrating tools to use (even
though they're still the most efficient
and accurate tools for some work), most
shaping planes are no more difficult to
master than bench planes. Each has its
specific uses, a shape or detail it cuts
best. Depending upon the work you do,
you might get by with very few shaping
planes. For example, buying only a half
dozen molding planes, along with a
rabbet plane you likely already own, you
can make a surprising variety of moldings
or details that will add immeasurable
interest to your woodworking. Even with
the simplest of the shaping planes
scratch stocks and spokeshaves-and lots
of ingenuity and patience besides, you'll
be amazed at the incredible variety of
shapes and details you can cut.
P L A N E S O N T H E L AT H E
I
don't remember where I
learned the trick, but planes
are useful shaping tools on the
lathe. Since 1'm not as good
with a skew chisel as 1'd like to
be, I use a plane to cut gentle
curves, straights, or tapers.
I still rough out the shape with
a gouge and cut the details
with a skew, but keep a block
plane handy for any of the
longer cuts.
Actually planes have been
used on the lathe for some
time. About a hundred years
ago, when nearly everything
was packed in barrels,
production shops smoothed
the outsides of barrels on huge
lathes with planes. To fit the
barrel the planes had concave
soles and, on some, wide steel
rollers at the toe and heel. A
movable rod above the lathe
hooked into a stout ring at the
toe of the plane to help hold it
against the rotating barrel (see
the engraving below).
My lathe technique is not
too different. The cut is
similar to one with a skew, but
the mouth and toe of the
plane give me a much more
controlled cut, just as they do
No. I 6
Conbined Harrel LatHe and Sander
when planing a flat surface.
Set the iron for a light cut,
angle it at about a 45 skew,
and plane down the spindle.
Keep the cut toward the
center of the iron, so as to
avoid catching the corner, or
relieve the corner of the iron.
For shallow curves, rotate the
plane to follow the shape as
you would planing it off the
lathe. Use a greater skew with
more of the sole against the
wood for the most accurate
straight cuts. It's amazing how
the curls fly.
Pl anes were used
on a barrel lathe to
smooth the outsi de
of barrel s. The pl ane
(vi si bl e at the ri ght
end of the l athe) i s
attached to the lathe
by a movabl e rod.
(Courtesy Roger
Smi th, Patented
Transitional and
Metallic Planes in
America, Vol. II. )
P L A N E S F O R S H A P I N G 209
SPECIALTY PLANES
Here Wratten, coope lives and makes / Ox bows, trug-baskets and hay-rkes.
Sells shovels, both for flour and corn, / And shauls, and makes a good box-churn,
Ladles, dishes, spoons and skimmers, / Trenchers, too, for use at dinners.
I make and mend both tub and cask / And hoop ' em strong to make them last. . .
-Early- 1 9th-century cooper's sign from Hailsham, England
I n an age when everything was made by
hand, the cooper, carpenter, chairmaker,
coachmaker, and others fulfilled all of
the needs of the farm, village, and town.
With native materials and ancient skills
passed from generation to generation,
they made objects of beauty and utility.
As the sign quoted above amusingly
relates, the work was of infinite variety,
from cradles to coffins, milk pails to
barrels. Craftsmanship was valued;
craftsmen were respected members
of society.
Craftsmen combine a unique under
standing of their materials, methods,
and tools. Some of this is taught, some
learned, and some just intuitively known
from years of thoughtful observation.
Chairmakers know that pine makes a
stable and easily carved seat; ash, finely
shaped and strong spindles; oak, tightly
bent bow backs; and maple or birch,
strong legs easily shaped on a lathe. They
also know what tools to use for every
step in making a chair, and the easiest
and fastest way to go about it. Their
Cooperi ng i s one of many trades that adapted tools to its speci al
needs, i n thi s case to shape and smooth the si des of curvi ng
barrel s. The stoup pl anes at the back of the tabl e smooth the i nsi de;
the scraper shave i n the foreground, known as a " buzz, " shapes
the outsi de.
craftsmanship is the purest melding of
form, function, materials, and technique.
What tools chairmakers need they make,
or they refine traditional tools.
Where once many of these tools were
simply made of wood and reinforced
with iron at points of wear and stress,
industrialization spawned a huge array
of long-wearing cast-iron designs.
Some were old patterns recast in iron,
others were new tools that manufacturers
like Stanley were only too happy to
design, make, and sell. Along with
industrialization came the mechaniza
tion of most trades, changing them
forever. Certainly some trades prospered
Cpatternmaking for one), but for the
most part as machines did more of the
work, there was less demand for
traditional tools and the craftsmen
skilled in using them.
21 1
This chapter is about some of these
specialty or unusual planes, often used
by a single trade for a specific purpose.
Some are unusual because of the way
they work, such as cutting useful
shavings rather than a surface as most
planes do. Some push the limits of what
a plane is. Although some of the trades
that used them are nearly obsolete, all of
these planes once were, and many still
are, the best tools for certain work.
Cooper's Planes
Coopering i s an ancient trade, well
known to the Romans and mentioned
in the Bible. Before cardboard and
plastic, barrels, firkins, and hogsheads
were the universal containers. Beer,
whale oil, dry goods, fruits or nails, they
were all shipped in barrels easily rolled
along wharves or into wagons. The
village cooper used the same methods
and tools to make sap buckets, milk pails,
churns, water tubs, and more. Every
village needed a cooper. Although the
trade is much diminished today, coopers
are still at work fashioning tubs and
barrels for aging wine, whiskey, vinegar,
and hot tubbers.
To make a barrel takes a keen sense of
measuring by eye and knowing your
materials-how they will respond to the
shaping and steaming needed to bend
them into the characteristic bulging
shape. Each barrel is made to hold a
specific measure, liquid or dry, which
requires a certain number of staves of a
length, taper, and bevel to fit together
tightly. Making and fitting the hoops is a
challenge, too. Hardest to make are
watertight barrels, strongly bulging and
made of stout staves to withstand the
pressure of fermenting liquids and the
rigors of shipping. Less demanding are
coopered barrels for dry goods, or the
so-called "white coopering" of pails and
2 1 2 C H A P T E R E L E V E N
Ron Rai sel i s, the cooper at Strawbery Banke Museum i n Portsmouth, New Hampshi re, shapes
whi te-oak barrel staves on a l ong and heavy cast-iron j oi nter pl ane. Thi s i s the way coopers
have always done it, trusti ng t hei r hand and eye to get the taper and bevel ri ght.
churns. While some of the necessary
tools are familiar to the carpenter or
furniture maker-a jointer plane or
drawknife, for example-most fit the
needs of no other trade.
"Wet" coopers usually work with
green wood, preferably straight-grained
and split-out white oak. It bends well, is
tough, and resists rot. The cooper shapes
the staves with a drawknife and ax and
puts them aside to dry to reduce any
shrinkage that could open up the joints
later. By eye, he cuts the tapers and bevels
on each stave, pushing them over a long
jointer plane used upside down and with
the toe end raised on a small stand (see
the photo above) Although the plane
looks and works like a carpenter's jointer,
its great length (up to 6 ft. and more)
and heft make it easier to bring the work
to the tool. The taper of each stave
defines the eventual shape of the barrel;
the greater the taper toward the center,
the more pronounced the bulge and the
stronger the finished barrel.
The next step is to draw the staves
together at one end with temporary
hoops and place the barrel atop a blazing
..
(f bin (in Qttntr / lhb maW o(Q/
:u ortn IZehneh l (jcten5o(/
abwai/6ctma(fftM/fccfcl i jI0l
:ie Qttten "nb Wtinfd Ier / wdtn/
itrdltr madn I biccn "hb binbelt/
marcoubr t6ut man bel mir fl!chl
2ud macT id it lidlcr "I etu6c1
@cn tfancfurt /ttipis "hI iu&iS
a i; "
An earl y German etchi ng of a tradi ti onal
cooper at work shapi ng staves.
kindling fire built in a metal basket
called a cresset. The heat and moisture
in the wood (plus an extra swabbing of
the inside of the barreD soften and steam
the staves. The cooper dl ives on more
,
temporary wooden hoops to bring the
staves together in the shape of the
completed barrel. With a drawknife or
adz he then bevels a "chime" or chamfer
around the inside edges at both ends.
The chime helps the barrel take the abuse
of shipping without worry of breaking
away the short grain where the head
joins into a groove cut just below the
chime. The cooper then levels the top
and bottom of the barrel with a plane
resembling a curved jack called a topping
plane (see the top photo at right).
Next follow two tools that are unique
to coopers, a howel and a croze. The
howel is really no different from a
compass-soled plane attached to a large
curved fence that rides along the top of
the staves (see the photo above). The
howel cuts a smooth shallow hollow, to
With a toppi ng
pl ane, whi ch i s
nothi ng more than
a curved jack pl ane,
the cooper l evels
the tops of the
staves to create a
smooth surface to
gui de the next tools
( howel and croze) .
The howel cuts a
shal l ow hol l ow
around the i nsi de
edge top and
bottom; it is followed
by the croze (shown
i n the foreground) ,
whi ch cuts a narrow
groove to fit the
bevel ed barrel head.
Both tool s have
large round fences
that ri de on top of
the leveled staves.
give a level place to cut into with the
next tool-the croze that cuts a narrow
groove for the barrel head. The croze has
a similar wide fence that rides on the
ends of the staves, but with either a saw
tooth type cutter or two nickers and a
single tooth like a router plane. The head
S P E C I A L T Y P L A N E S 2 1 3
that fits into this groove is made up of
two or three boards doweled together
and smoothed with a large shave called a
swift. The cooper cuts the edges to a fine
bevel to fit snugly into the groove cut by
the croze.
Shaves are used to
smooth different
parts of the barrel .
From the top, a
l arge shave cal l ed a
swi ft, wi th a flat sol e
for fl atteni ng the
head; an i nshave,
used wi th a stoup
plane for smoothi ng
i nner surfaces; and
a l arge shave for
cutt i ng the bevel on
the head.
Vi ol i nmakers use
some of the smal l est
and most beauti ful
pl anes to hol l ow to
a gentl e curve the
i nsi de of the top
and back of a viol i n
and l arger stri nged
i nstruments.
2 1 4 C H A P T E R E L E V E N
Before setting the barrel head, the
cooper smooths the inside surface of
some barrels with a stoup plane and an
inside shave (or ins have). A stoup plane
has a convex sole in both directions to
work within the doubly curved staves
(see the photo on p. 210). The cooper
smooths the outside with a downright,
another large-handled shave, and a
similar scraping tool called a buzz. The
final step is to fit the head and drive on
wooden or steel hoops.
Making the barrel has taken a number
of planes similar but different from
those of other trades, each perfectly
adapted to a cooper's work shaping
curved surfaces. And if he has done his
work well, the barrel will hold the exact
amount of liquid and not leak.
Violinmaker's Planes
Although it's much more subtle, many
stringed instruments have the same
bulging shape as a barrel. Violins, cellos,
violas, and basses have it-and for the
same reasons that a barrel does. The
gently curved top and back give the
instrument strength with lightness.
The parts can be very thin (as thin as a
millimeter at the edges of the back in a
violin), yet require little internal bracing
and still be strong enough to hold up to
centuries of being played and handled.
Just as important, the thin, bowed
shape is flexible to give power to the
instrument's sound.
To shape the back and top, violin
makers use the smallest of planes-finger
planes. Many are less than 2 in. long,
with flat soles or soles curved in two
directions like the cooper's stoup plane.
They are finely made of gunmetal, with
curving sides and beautiful screw caps or
wedges. For hollowing against the grain,
or for planing a highly figured tiger
maple back, a violinmaker can replace a
straight iron with a toothed one.
To shape a back or front, violinmakers
cut a blank roughly to shape and refine
the outside with a gouge and straight
soled planes. They shape the inside with
the same gouge and tiny finger planes.
Where the top is a uniform thickness,
Smal l pl anes for shapi ng chai r seats ( here, resti ng on a pi ne seat for a
Wi ndsor chai r) have doubl y compassed soles to work i nto the hol l ow.
These two unusual shaves coul d be used to hol l ow a pl ank seat or
just as easi l y to shape a shovel or scoop.
the back tapers from thicker at the
middle toward a thin edge. Consistency
of the thickness is important for the tone
of the instrument. Small finger planes
just fit this work, accurately and
carefully hollowing the back and top.
Chairmaker's Planes
Chairmakers hollow plank seats with
larger versions of finger planes, with the
same doubly compassed soles. Many of
these planes are either craftsman-made
or modified to work a particularly
favored seat shape, from deeply hollowed
to one more shallow. Just as useful are
large shaves, often called travishers, with
strongly radiused irons and handles
curving away from the work to keep the
user's knuckles out of harm's way (see
the bottom photo at right). As with the
planes, a chairmaker needs a number of
travisher shapes to fit specific seat shapes.
To shape a seat, chairmakers start
with a thick plank (usually white pine or
basswood) cut roughly to shape. They
hollow the center and shape the edges
with shaves and planes, leaving a shape
that's both comfortable and practical.
The hollow is deeper toward the back to
give the sitter a slight backward cant, and
it's left thickest where strength is needed
to joint in legs, spindles, and rails.
Chairmakers have adapted one other
plane to their needs: a scraping spoke
shave known as a devil (see the photo on
p. 173). It's used to shape and smooth
spindles and the "bows" for rails and
arms. With a short sole shaped to fit the
circumference of the part and a bone or
brass insert ahead of the blade to counter
wear, it's the most practical tool for
smoothing curved parts. A devil can
follow complex shapes, such as the
continuous back rail on some Windsor
chairs-a task nearly impossible with
other planes.
Travi shers are shaves used to hollow and
shape a seat. They have upward-sweepi ng
handles to keep the chai rmaker' s knuckles
wel l out of the way.
S P E C I A L T Y P L A N E S 21 5
A large handrai l pl ane (at ri ght) shapes the si des of strai ght Qr gentl y
curvi ng sections of handrai l . An ogee, hol l ow, or cappi ng pl ane (at
l eft) cuts the rounded top profi l e.
Short-sol ed mol di ng pl anes shape the curved sections of the handrai l .
No matter how many shapes stai rmakers owned, for some stairs they
had to make speci al pl anes.
Stairmaker's Planes
In all of their ornate detail, stairs were
once one of the dominant architectural
features in a house; some still are. Stair
makers who build such stairs share a
similar problem with chairmakers who
fair curving chair rails-that of shaping a
continuous curved hand railing. Even the
simplest handrail has a decoratively
molded top and sides. Elegant handrails
have even more elaborate profiles and
curves that follow the turn and rise of
the steps between newel posts, around
landings, and between flights. More
complicated still are circular staircases
with curving handrails, requiring great
skill and a number of special tools.
Straight and gently curving sections of
handrail are molded with large handrail
molding planes (see the photo at left
2 1 6 C H A P T E R E L E V E N
above). A capping plane cuts the
rounded top profile, and another (or
others) profiles the sides. The trickiest
part is shaping more radically curved
sections-such as a sweep up to a newel
or the scroll that starts the railing at the
first step. Planes and spokeshaves are the
first tools used, to rough out the shape
and molded profiles. The stairmaker
refines the profile with shaped scrapers
and shaves or uses a number of short
soled molding planes (sometimes
custom-made for just that stairs).
Miniature finger planes are useful, too,
especially where the curve is tight.
Molding planes of all sorts are also
needed to build a flight of stairs. Nosing
planes (large hollows) cut the semi
circular shape on the edge of each tread.
Under each is another fine molding,
straight or curved to fit the tread. Newels
that aren't turned are often made from a
number of applied moldings and small
beveled panels. Any good joiner is likely
to own many of these planes. Even today
with routers and shapers, building a
gracefully curving stairs and handrail
takes a variety of special shaping planes.
Coachmaker' s Planes
Many trades were involved i n building
carriages and coaches, from the
wheelwright fashioning wheels to the
upholsterer fitting the seat cushions and
the blacksmith forging the iron axles and
fittings. The coachmaker built the
wooden coach body, curved in every
direction as much for elegance as
practicality-for strength and to
maximize the interior space suspended
between the wheels. Working with few
straight lines, coachmakers required a
number of short-soled and specialty
planes for cutting curved rabbets,
grooves, and moldings. Such tools were
useful in many other trades as well, such
as for a joiner fitting the interior of a
ship, a furniture maker cutting curved
moldings, or a sashmaker molding
shaped windows.
Just as each set of stairs is different
and poses specific challenges, so it was in
building coaches, carriages, sleighs, or
any one of the many designs of horse
drawn vehicles. Building large coaches
required the most skill. They had to be
strong to withstand the abuse of rough
roads, yet light enough to be able to be
moved easily by a team of horses. To the
strong frame the coachmaker fitted
panels, doors, and windows, often
curved in one or more directions.
A coach maker's planes had to have
short soles to work curves; there was less
need for the long, straight work that a
longer-soled plane could do. Many are
either very short, or the heel is cut away
into a beautiful and functional curved
"pistol grip" (see the top photo at right).
To cut moldings, rabbets, or grooves
around curves, the sole is often
compassed. To work into tight places,
some rabbet planes have a sole wider
than the rest of the body, known as a
T-rabbet (see the bottom photo at right).
This unusual design allows the plane to
be used on its side, much like a side
rabbet plane, to adjust a curved groove.
Coachmakers showed real invention
in their plows and routers for cutting
grooves along tight or changing curves.
The simplest tools are routers with large
handles and very short soles and fences.
Most have two irons, on opposite sides
of a fence, to work right-handed or left
handed with the grain. With shaped
irons, the same tools could mold along a
curving edge. Plow planes such as the
Acoach maker needed short-soled pl anes to work curved parts. The shape of the pl ane body
evolved to an el egant and functional pistol grip, al l owi ng one-handed control.
One of the few
coachmaker' s tool s
made of cast iron
rather than wood,
thi s T-rabbet pl ane
has a sol e wi der
than the body for
worki ng in ti ght
places or for use
on its si de to adj ust
a groove.
S P E e I A L T Y P L A N E S 2 1 7
To pl ow grooves for
panel s in curved
frames, a coach
maker' s pl ow pl ane
had to have a very
short skate and
fence. The top pl ow
has an adjustabl e
fence; the si mpl er
one bel ow it has a
fixed wooden fence.
I n the foreground
i s a smal l mol di ng
pl ane.
To save space i n a tool chest, pattern maker's pl anes often had i nterchangeabl e wooden sol es
and i rons to work the di fferent radi i common i n thei r work.
2 1 8 C H A P T E R E L E V E N
one in the rear of the top photo at left
have a very short skate and fence to
allow the plane to follow any curve.
Stanley used the same design idea in
the # 1 96 curved rabbet plane (see the
top photo on p. 1 25). A rare tool today,
this plane would have been useful to
the few coach makers still working by
the early 20th century. Coachmaking
has not disappeared quite yet. The tools
and skills survive with the few makers
left restoring and making coaches
and the wooden parts for some fine
horseless carriages.
Patternmaker's Planes
Pattern makers use some of the same
curved-soled planes as the coachmaker.
They were once some of the most highly
skilled craftsmen in every foundry,
producing the wooden patterns from
which each casting was made. Although
patternmaking is a disappearing art,
patternmakers are not yet all gone. For
example, there's a full-time patternmaker
at Lie-Nielsen Toolworks, designing and
making patterns of every plane and part
they cast (see pp. 237-238).
Patternmakers have to understand
their materials, both the wood for the
patterns and cast iron, bronze,
aluminum, or whatever the eventual
casting will be made of. Every metal
shrinks differently as it cools, which
means that the pattern has to be made
slightly larger to compensate. It's also the
patternmaker's job to design the pattern
so that it can be cast accurately and so
that it has all of the necessary details and
tolerances for later machining.
Patternmakers make their patterns
from a stable fine-grained wood such as
mahogany or cherry. To release the
pattern from the sand mold easily, they
shape every surface with a slight taper
known as draft. Where surfaces join at
right angles, they often fit small leather
or wood fillet strips to strengthen this
joint in the finished casting. Curved
sections they shape with spokeshaves,
planes with shaped soles, or finger planes
when necessary. To take up less space in
their tool chests, patternmakers use a
variation on the combination plane.
The plane has a cast-iron body and thin
interchangeable soles and irons, each
with a different curvature (see the
bottom photo on the facing page).
The most unusual patternmaker's
plane is a corebox plane (see the photo
above). While the name and appearance
of the tool might be familiar to some,
what it makes and how it does it are far
less obvious. Whether owner-made of
wood or either of the two versions
Stanley made of cast iron, corebox planes
have two wings that meet at a right angle
where the V-shaped iron projects.
To see such a plane you'd have no
idea that it is capable of cutting an exact
semicircular hollow of any diameter
Unusual in appear
ance and functi on,
a corebox pl ane
cuts a semi ci rcul ar
hol l ow, used for
formi ng cyl i ndri cal
cores for casti ng.
The l arge corebox i s
the bi ggest Stanl ey
made ( #57) , with
t hree extensi ons
and radi us rods.
In front is a smal l er
Stanley #56 (wi th
other pattern maker
tool s) .
(depending on the width of the wings).
It works on the principle that only a right
angle-the sole of the plane-can be
inscribed in a semicircle. Patternmakers
first plow two grooves with a plow the
exact diameter of the desired half-circle
and either parallel to each other or
diverging so as to cut a tapered hollow.
They waste what wood they can with
hollows or other planes and finish it to a
consistent shape with the corebox plane,
one pass after another across the whole
curve. The Bayley corebox plane (shown
S P E C I A L T Y P L A N E S 2 1 9
The Bayl ey corebox pl ane cuts a semi ci rcul ar hol l ow. The pl ane rides
along the top of the stock, and the cutter rotates a few degrees with
each pass.
Rounder planes work on the same pri nci pl e as a l athe, shavi ng a
pi ece of wood round as it is fed up through the mi ddl e. The l arge
rounder i n the foreground cuts onl y one di ameter; the more compl ex
"wi tchet" at rear i s adjustabl e and wi l l cut tapers and tenons.
in the photo at left above) works on a
similar principle, except that the plane
stays in the same position and the cutter
rotates a few degrees after each pass.
Why make such an accurate semi
circular hollow? By making a section
twice as long as needed, cutting it in half,
and joining the parts, the pattern maker
has an exact cylinder that is a mold for a
core (made from sand and a binder to
give it strength). Some castings, such as a
large sheave meant to slide onto a shaft,
are better cast with a hollow for the shaft
rather than solid. Casting it solid would
mean drilling a hole for the shaft
afterwards-not easy to do if it's a large
diameter. The solution is to make a
pattern of the sheave as mounted on a
220 C H A P T E R E L E V E N
short shaft, make a sand mold, remove
the pattern, and slip in a sand core the
size of the shaft. The core fits neatly into
the sand-mold impressions left by the
short wooden shaft. It's a simple and
elegant solution involving an unusual
hollowing plane.
Rounder Planes
Whereas the patternmaker's corebox
plane cuts a perfect semicircular hollow,
a rounder cuts a cylinder, such as for
ladder rungs, handles, or dowels. Not to
be confused with a round plane (the
mate to a hollow), rounders shave
around the outside of a bolt of wood like
a simple pencil sharpener. Dynamically,
it's a difficult cut, so they don't leave a
perfectly smooth surface.
The photo at right above shows two
versions of rounders. The simpler one is
nothing more than a tapered hole
drilled into a burly hunk of hardwood,
with two handles and an iron mounted
tangentially to the hole. It might have
been used to taper the ends oflarge
pump logs, joined together to form the
earliest water systems. Smaller versions
cut long handles or stails far more easily
than on a lathe. The idea is simple
enough that any craftsman can make his
own rounder, for such needs as cutting
dowels of any diameter on or off a lathe.
The rounder at rear in the photo,
known as a witchet, has more bells and
whistles. It's adjustable to cut different
diameters, the "sole" is plated to resist
wear, and it has two irons. The shorter
iron cuts into the end grain, the other
shaves the diameter. It's possible to cut
tapers by turning the handscrews and
changing the cutting diameter while
working down the length of the stock;
it's also possible to round the end into
a tenon.
Spoke Pointers
Spoke pointers work on the same pencil
sharpener principle as rounders, but
they are more acutely tapered and the
stock does not pass through the tool.
The name suggests their association with
wheelwrights and pointing the ends of
spokes. I find them useful for tapering
the end of any round part-dowels,
round tenons, or the small pins I drive in
to lock a mortise and tenon.
I have a number of sizes. The smallest
is an inexpensive pencil sharpener with
two sizes of holes. It will round pins or
dowels as small as 's in. diameter. Since
the iron is set at a very low angle and the
cut is a slight skew, it cuts fairly cleanly.
I also have two larger-diameter spoke
pointers with square drill shanks meant
to be used in a brace. These are handy for
pointing many parts consistently (by
counting the revolutions, for instance),
but it also means clamping up the parts
to have both hands free to run the brace.
It's quicker to hold the wood and screw
the spoke pointer around the top a few
times by hand. I set the irons in all of
them for a light cut and fine-tune by trial
and error.
Hollow Augers
Another variation of the rounder is a
hollow auger, a bit-brace-driven plane.
The cutting end looks like a miniature
plane with a sole, an iron, and a cap that
clamps it in place. It cuts round tenons
on the end of round or square parts, for

Spoke poi nters cut

a round taper on
the end of a spoke,
l adder rung, or
round tenon.
STEARNS' PATENT SPOKE POINTERS.
Nos. 1 and 2.
WITH GRADUATED ADJUSTABLE SHANK.
Price, each,
It U
such things as chair stretchers, ladder
rungs, and wheel spokes. As the hollow
auger cuts around the shoulder of the
tenon, the tenon feeds into the throat
and helps support and guide the tool.
There are many variations. Some cut one
size tenon only; others are adjustable
over a range of sizes. They can have two
irons or one.
Used i n a bi t brace,
this adjustabl e
hol l ow auger by
E. C. Stearns cuts
vari ous si zes of
round tenons to fi t
any morti se exactly.
The cutti ng end
l ooks and works l i ke
a smal l pl ane. I n
t he foreground is a
smal l spoke pointer.
I have an adjustable model made by
E. C. Stearns sometime in the last
quarter of the 1 9th century (see the
photo above). It's most useful whenever
I' m cutting many identical round
tenons, or when it's easier to bring the
brace and hollow auger to the work,
rather than turn the tenons on the
S P E e J A L T Y P L A N E S 221
One of the more unusual pl anes, a shoe-peg pl ane cuts uniform square-tapered poi nts on an
end-grai n bl ock, whi ch is later spl i t apart i nto hundreds of ti ny shoe pegs.
lathe-for long pieces, for example.
This model will cut tenons from '+ in.
to 1 % in. diameter to fit any mortise
exactly, but not always easily. The iron
is tricky to set-it must project just
enough to the side, as in a rabbet plane.
On this tool, the tenon feeds through
two V-shaped jaws that open and close to
accommodate different diameters. If the
iron projects too much, the tenon is
slightly undersized and it wobbles in the
guides; if it doesn't project enough, it's
too tight. It's typical of the shortcomings
of any tool meant to do everything.
222 C H A P T E R E L E V E N
Shoe-Peg Planes
Another unusual plane that cuts a
specific shape in end grain is a shoe-peg
plane, used for cutting small, square-
ta pered pegs. There was a time when
these small hardwood pegs were used to
attach heels and soles to shoes and boots.
Burlington, Vermont, was once the shoe
peg capital of the nation, where the
single largest factory cut as many as four
hundred bushels of shoe pegs daily
The shoe-peg plane by A. Gillet
shown in the photo above looks like a
jack plane with a removable fence. It's
such an unusual design that it would be
hard to say if it is typical of other shoe-
peg planes or if it's a recut bench plane.
The sole has 15 sharp V-grooves running
down its length, similar to a reeding
plane (though a reeding plane would
have 3 or 4 at most). The iron is toothed
like a saw but cuts only over about half of
the grooved sole.
A shoe-peg maker used this plane on
the end grain of a very straight grained
chunk of maple or birch, so that the
finished pegs could be split off easily and
consistently. First he ran the plane a few
times in one direction across the block,
using the fence or a temporary wooden
strip as a guide. By setting the plane over
and using the cut grooves as a guide (just
as with a reeding plane and explaining
why only part of the iron cuts), he cut
progressively over the whole width. He
then planed at right angles to the first
grooves in the same way, to leave the
block covered with evenly spaced square
tapered points. He split the pegs off in
strips with a chisel, and then into
individual pegs-each only about '
'
:in.
square with nicely pointed ends-ready
for driving into a heel.
Sashmaker's Planes
One of the few other planes designed
specifically for shaping end grain is a sash
coping plane. A sashmaker used one to
cope or profile the ends of each rail and
sash bar (or muntin) in a window, to
neatly fit the mirror-image profile cut on
the stiles. Coping is not possible with
every molding profile, but it's the fastest
and neatest way to join the molded edges
of stile and rail. To minimize tearout,
either the work is put into a special
saddle template with an end shaped like
the coping cut, or a number of rails and
muntins are clamped side by side and
coped together. There are a number of
different versions (and profiles that like
most planes conformed to prevailing
tastes), but all cut along the end grain in
the same way.
Sashmaking takes skill and a number
of other special molding planes. While
they don't look or cut any differently
from other wooden planes, the profiles
are specific to sashmaking. What they
better represent is how sashmakers
combined cutting functions to make
the most efficient planes possible. Take,
for example, cutting muntins, the thin
bars that divide the panes of glass. An
old method was to cut the putty rabbets
to hold the glass and putty, then mold
one side of the face and then the other
four cutting operations with two planes.
Eventually someone had the idea of
joining together a rabbet and molding
plane, a so-called stick-and-rabbet or
sash plane, to cut the molding and
rabbet at the same time (see the photo
at right). Cutting muntins this way
takes one plane and two cuts, and it's
a lot more accurate.
There are more reasons why sash
planes are efficient. Some versions have
a single body and two irons (easier to
sharpen and tune than a single wide
iron). Others are split, so that with shims
between the plane bodies or separated
by adjustable screws of some kind, the
same plane will work thicker stock. Only
the flat between molding and rabbet is
wider; the molding profile is the same
(so the same coping plane still works).
And since the plane references against
the outer edge of the molded profile,
any slight variation in the stock thickness
shows up as a wider putty rabbet, which
is easily planed down after the window
is assembled. This saves time in that the
stock doesn't need to be thicknessed
carefully or planed smoothly to start.
A minute saved here, or a tool that
worked more accurately, added up to
considerable time savings when
fashioning all the many windows for
a house.

I So

fc. .
.
'
,
1
:). . 2
4, 4 " . .

- z

!


;
1

j
i
l

! "
. II

_ _ l

- l
.

I'

'I

I

T
0

'

1
e

. .. . . . . . . . . ".
. . . . . . ... . .. . . .
Sash copi ng pl anes shape the end grai n of rails and munti ns to neatly fi t the mi rror-i mage
profi l e cut on the stiles. Si nce these pl anes cut l yi ng on thei r si des, some i ngeni ous pl ane
makers added another pl ane body at r i ght angl es to the worki ng pl ane, for a handhol d.
Rather than use
separate mol di ng
and rabbet pl anes,
a sash maker' s sti ck
and-rabbet or sash
plane combi nes
the work of both.
It effi ci entl y and
accuratel y cuts the
mol ded profi l e and
putty rabbet at the
same t i me.
S P E e [ A L T Y P L A N E S 223
Pl anes whose
purpose i s to cut
shavi ngs rather
than a surface are
parti cul arl y unusual .
Aspi l l pl ane cuts
ti ghtl y twisted
shavi ngs, j ust ri ght
for l i ghti ng a pi pe or
candl e f r om the f i re
in the hearth.
Spill Planes
Taking a break from his work (since he is
working so efficiently), a sashmaker
might run a piece of scrap pine across his
spill plane. The long, tightly twisted
shavings called spills were just the thing
to light his pipe from the embers in the
fireplace. Such planes are not rare, but
they are very unusual in the plane world.
They're one of the few planes where the
shaving is the object, not the surface the
plane cuts.
224 C H A P T E R E L E V E N
Spill planes are all different. A few
commercial plane makers offered them
for sale, but most are simple enough to
be easily made by the owner. All that is
necessary is a sharply skewed iron and a
fence either to guide the scrap against or
to guide the plane. A common design
looks like a molding plane with a wedged
iron and side escapement throat (see the
photo above). Another I've seen has a
small, round exit hole for the shaving, to
help curl it all that more tightly.
Making a tight spill is trickier than it
might seem. Set properly, the skewed
iron does all the work, but it still takes a
slow and steady stroke. Cut too quickly
and you'll make a nice shaving, but it will
not be twisted much and will burn up
too quickly. Take too coarse a cut and the
shaving won't curl well either. Once you
have it, the spills are uniform and tight.
With matches so common today, we
forget how spills were once one way our
ancestors moved fire from hearth to
candle, lantern, or pipe.
Spelk Planes
There i s another plane whose purpose is
to make shavings-a spelk plane. There
are many variations, some of which have
different names, but they all work
basically the same. A spelk plane makes
shavings of a certain width or thickness,
for weaving baskets, bending into small
boxes, or if they are wide enough, for
bending into traditional round cheese
boxes. Shakers in Canterbury, New
Hampshire, used a spelk plane of sorts to
make the fine poplar strips the sisters
wove into the poplarware boxes they
were known for. Another variation is a
Japanese plane that shaves long, wide
shavings used for wrapping paper. The
super-surfacer planer evolved from this
spelk plane (see the sidebar on p. 1 54).
Some spelk planes resemble old
fashioned cabbage graters, with a
spokeshave-type iron mounted across the
heavy stock. The low angle of the iron
works well with the grain, cutting and
splitting the spelks (which are left
somewhat rough). The thickness of the
shaving is regulated by exposing more of
the iron and opening the throat. Driving
the plane over the stock or the stock over
the plane takes such force that most
planes have a number of handles for
additional hands. Cutting stock slightly
green is easiest.
Basketweavers and hatmakers use a
type of spelk plane for cutting flat strips
or for sizing them to a consistent
thickness. To produce uniform strips,
the stock is first scored with a knife or a
series of knives ganged together and then
passed through the spelk plane. Shaker
sisters used this method to make fine
poplar strips as narrow as 's in.
S p e l k Plane
Spelk emerges through the mouth at the
rear of the plane.
Blind Nailers
Falling somewhere between these
unusual shaving-making planes and
ordinary planes that leave smooth or
shaped surfaces is a blind-nailing plane.
Its name clearly identifies what it does
cutting a shaving from the surface to
hide a nail. It's how it does it that's
quite different from the way most other
planes work.
Stanley'S #96
bl i nd-nai l i ng pl ane
(or chi sel gauge)
i s as scarce as i t
i s uni que. It gui des
a narrow chi sel or
gouge to cut a
shavi ng that' s
perfect for hi di ng
a nai l when the
shavi ng i s gl ued
back i n pl ace.
For one thing, a blind nailer is
unusual in that it's small, only 2 '1 in.
long. For another, the plane's function is
to guide a small chisel (or a gouge) in
place of the small iron you might expect.
This is where it gets its other name: a
chisel gauge. Clamped on the end of a
chisel, it guides the cut to curl up a
shaving. The idea is then to back the tool
out and leave the shaving attached, drive
a nail under it, and glue it invisibly back
S P E e [ A L T Y P L A N E S 225
Thi s butt morti se pl ane by C. M. Rumbol d Co. has an unusual l y wi de throat. so the user can
see how the plane is cutting as it levels the bottom of hi nge mortises or si mi l ar recesses.
into place. Simple enough, but it still
takes a feel for the tool to get it right. Too
deep a cut and the shaving is brittle; too
shallow and it's hard to get the thin edges
glued back down. I prefer using a shallow
gouge, for a fine chip that's strong and
flexible. Blind nailers might seem like
funny little tools, but they're perfect for
what they do.
Butt Mortise Planes
A larger relative to the blind nailer, a
butt mortise plane works on the same
principle of a simple plane body
supporting a chisel iron. What's
unusual about a butt mortise plane is
226 C H A P T E R E L E V E N
that its throat is wider than the length
of the blind nailer-nearly 3 in. wide
No other planes but routers have such
wide throats.
The main use of a butt mortise plane
is to true the bottoms of mortises for
locks, hinges, an inlay recess, or perhaps
the background of a carving. The easiest
way to use it is first to score and chisel
the recess, remove most of the waste, and
then use the tool for a final smoothing
and leveling. In cutting a mortise for a
hinge, this eliminates the additional step
of marking out its depth. I set the depth
of the iron to the thickness of the leaf
held against the sole next to the iron.
With the same setting, all of the hinge
mortises are identical.
Another plane could make the same
cut, but here's where the unusually large
throat helps-you can see where you're
cutting. A router has an open throat for
the same reason and could be used with
care, but the sole is not the best shape to
work on the edge of a door easily. The
lack of a sole just ahead of the iron of a
butt mortise plane is unimportant, since
a perfectly smooth surface is not the
main object.
Interestingly, this was one of the few
useful plane designs that Stanley
made. Although wooden versions had
been around a long time, it wasn't until
the 1950s that C. M. Rumbold Co.
started making this design in cast iron,
not too many years after Stanley was
starting to cease production of some of
its specialty planes.
Table-Leaf Planes
As the name suggests, table-leaf planes
are used to cut the joint for a drop-leaf
table. While no different from other
molding planes in appearance or
function, table-leaf planes are one of a
number of unusual planes meant to be
used in pairs to cut a special joint. The
same sorts of planes were used by many
trades, such as the casement-sash maker
for the meeting joint of sashes, a case
maker cutting dustproof joints between
doors, or doors and frame, or a plane
maker cutting complex joints for
inlaying boxing.
Table-leaf planes are actually quite
simple, just a pair of fenced hollow and
round. At first glance, the joint they cut
doesn't seem all that complicated either,
but actually making a properly fitting
table-leaf joint is quite subtle. You can
use a matching pair of hollow and round
or scratch stocks, but it's easiest by far
with a well-tuned pair of table-leaf
planes. With large fences, it's easy to hold
the planes against the leaf and table to
cut a consistent and tight-fitting joint.
Tuning the irons to one another is then
the only tricky part.
What these and many other planes
like them represent to me is the way that
craftsmen adapt their tools to work more
accurately or more easily. Perhaps it's
adding a special fence and curving the
plane's sole as with a cooper's croze,
shortening a plane to work the complex
shapes and curves of a handrail, or
combining the functions of two tools
into one as with the sashmaker's sash
plane. The special demands of each trade
require unique tools. Some of these tools
are unusual because they are unfamiliar,
from a trade long diminished from a
Tabl e-leaf pl anes
are no different from
a matched pai r of
hol l ow and round,
with the si mpl e yet
very i mportant
addi ti on of fences to
guide the pl anes for
greater accuracy.
century ago. While none of us is likely to
use a shoe-peg or spelk plane, the
usefulness of their basic concept might
never be obsolete. As for the rest of the
planes in this chapter, many are still
useful today-maybe not every day, but
for those situations where no other tool
works quite as simply or as well.
S P E e I A L T Y P L A N E S 227
CONTEMPORARY
PLANE MAKERS
Of course the really good plane becomes an instrument, it becomes
something that you want to make music with.
-James Krenov, 1 996
Craftsmen have been making their
own planes for a very long time. In earlier
days, plane making was an extension of
the woodworking profession, and
fashioning a kit of tools was a natural rite
of passage from apprentice to journey
man. As commercial plane making
expanded to supply every type of
wooden plane imaginable and later
manufacturers like Stanley began to
produce an incredible variety of metal
planes for a modest cost, there was less
incentive for a craftsman to make all but
the most specialized tools. He simply
bought the planes he needed.
During the many years that Stanley
dominated the hand-tool market, many
competitors came out with their own
plane designs. Some of the tools were
excellent, every bit as good as what
Stanley was making. Yet every one of
these companies has since stopped
making planes, not because their
products were poor (Stanley's were
quite mediocre for many years after
World War II), but rather because, up
until quite recently, there has been a
declining market for all hand tools.
It was the same way in England, as some
of the finest toolmakers-Norris, Spiers,
Whi l e greatl y di mi ni shed from al most a century ago, pl ane maki ng
goes on. Anumber of smal l busi nesses l i ke Li e-Ni el sen Toolworks of
Warren, Mai ne, are maki ng beauti ful pl anes based on cl assi c desi gns
( here, the Bed Rock =604).
Preston, and others-closed up shop.
Woodworking machinery captured
imaginations; hand tools represented
hard and sweaty work.
Some of the romance of working with
one's hands for pleasure or income has
returned. I am certainly among those
craftsmen who have chosen to make a
living designing and building furniture
rather than, say, pursuing engineering or
law. Every one of us needs all types of
quality tools for our work. Up until
recently this has meant hunting for old
tools at flea markets, auctions, and tool
dealers. Simultaneously, collectors and
229
historians are just as interested in hand
tools and the technology they represent.
The result is pressure on the market for
the classic tools of Stanley, Norris, and
others. The rare tools get ever more
expensive and beyond the reach of most
of us. Luckily, some of those same
craftsmen have turned their energies to
redesigning and remaking some of these
classic tools.
This chapter tells the stories of five
of those plane makers. All of them have
been captivated by the romantic vision
of making beautiful hand tools as good
as or better than the originals. They got
started for different reasons. One maker
was frustrated trying to work with the
best tools he could find. Others just
relished the challenge. Some had to work
hard to establish their businesses, but all
found a market for their tools. There will
always be a demand for good tools.
At the very least, these stories will
offer insight into how metal and wooden
planes are made. While the subtleties of
the design, materials, or machinery
might be different, plane making has
changed very little over the years. I hope
that these stories might also inspire you
to make a plane or two for yourself. It
will give you a different perspective and
understanding of your tools. Cabinet
maker and plane maker James Krenov
shares this thought when he says that his
"first little attempt with [ making] a
plane that succeeded might have been
the turning point in my life, because it
opened up the fact that tools can be
better, that tools can be personal and
more intimate. Had I failed, I might have
just fallen back into the general pattern,
which doesn't mean I wouldn't have been
a cabinetmaker, but it might mean that
I would never be able to make music."
Plane-making techniques vary, but
almost none of them are beyond the
reach of anyone with curiosity and
230 C I-I A P T E R T W E L V E
modest skills. Anyone can make a
wooden plane. While casting bronze
planes would be difficult if not
impossible in a home shop, making the
pattern is not. Then it's just a question of
finding a foundry to do the casting and
taking it from there.
Ted Ingraham:
Wooden
Molding Planes
For a long time, wooden planes were
literally made by the millions. During the
years of peak production ( 1 870-1880),
catalogs such as Ohio Tool Company's
offered a dazzling array of nearly a
thousand different planes, from bench
planes to complex cornice planes to
simple hollows and rounds. Meanwhile
cast-iron planes, with their positive
adjusters and soles that stayed true over a
lifetime of work, were becoming more
competitive in terms of quality and
price. When cast-iron bench planes
finally came to dominate the market,
new combination planes (such as the
Stanley #55 and #45) further eroded the
market for wooden molding planes.
At one time a finish carpenter needed
a huge set of different molding planes-as
many as 60 different pairs-for cutting
specific moldings for everything from
window and door trim, to ornate crown
moldings, to small base moldings
completing the baseboards. As molding
machines and mill-cut moldings became
readily available, fewer moldings were
cut by hand with planes. Most houses
In the tradi ti on of past pl ane makers, Ted I ngraham stamps the toe of his wooden mol di ng
pl anes wi th a stamp he cut and fi l ed. Thi s pl ane cuts a l arge corni ce or crown mol di ng.
built today have generic millyard
moldings, if any, certainly none cut with
planes. But the need for molding planes
has not disappeared altogether. For
authentic moldings for restoration work
or building period houses, or as a way to
create any molding profile, wooden
molding planes are still the best tools.
Ted Ingraham started making
molding planes out of curiosity. Always
interested in the tools and methods of
the 18th-century woodworker and
restoring old houses at the time, it was
only natural that he would try his hand
at making planes. The success of the first
ones encouraged him to keep going.
Since then he has made dozens, including
many to cut specific moldings for his
period Georgian house. When I met him
he was taking careful measurements of a
very early square-armed plow plane, to
add to his growing log of planes to
reproduce someday. In his shop a few
months later he made a molding plane
and explained the process.
MAKING A WOODEN
MOLDING PLANE
The stock for the plane is a piece of
straight-grained, quartersawn yellow
birch. Birch was the choice of early
American plane makers, distinguishing
their work from English beech planes.
By the time plane making became a
commercial trade and the first catalogs
appeared, American makers had
switched to beech. Both woods are hard
wearing and stable and, as long as the
stock is well seasoned, make good planes.
Ted often starts with a hunk of firewood
cut into rough blanks and seasoned
upstairs in his shop. Earlier makers first
steamed the wood to speed the seasoning
(and enhance the color) and then set the
blanks aside for three years or more.
In some descriptions of plane making
great importance is put on cutting the
blank so that the sole is cut from the
wood closest to the bark. Years of
experience showed that this wood is
better able to hold up to wear and thus is
somewhat "harder." Just as important is
orienting the blank so that the grain
slopes toward the heel of the plane. In
use, the fibers will be smoothed down
and are less likely to catch and tear out,
damaging the sole or marring the work.
Few pieces of wood are perfect, and it's
here that Ted's experience is important
in knowing his material and the defects
that can be safely ignored.
Ted dimensions the blank (into the
plane stock) slightly longer than 10 in. by
3 V4 in. and slightly thicker than the
molding profile, in this case 1 Vz in. wide.
A first and important step is to
accurately square the stock-the long
grain edges and the ends. Accurate
layout, upon which all the cuts depend,
will then be much easier. The next step
is to cut the handhold, 1 ':in. deep and
one-third the width of the plane body.
Ted uses a fenced rabbet (a fillister) to
After di mensi oni ng
and squari ng the
stock, Ted cuts the
handhol d wi th a
f i I I i ster pl ane.
sink this wide rabbet accurately and
quickly (see the photo above).
Molding planes vary in width, but
they are cut to a uniform length and
height. Blanks can be made ahead of
time to speed large production runs, but
standardization also makes it easier
when cutting only one plane, because
the same jigs can be used to mark out all
the cuts for the throat, mouth, and
wedge mortise. Ted uses a pitchboard
(see the top photo on p. 233) laid along
side the stock to lay out the throat at a
bedding angle of 50, which is standard
for many molding planes. Carrying the
lines across the top of the plane he lays
out the wedge mortise in the center and
one-third the thickness of the handhold.
Depending upon the type of molding
plane he is making, he might also mark
out the sole for a fence cut into it. Even
though this plane will eventually cut a
reverse ogee, so far nothing distinguishes
it from another similarly sized plane
meant to cut an entirely different
molding profile.
C O N T E M P 0 R A R Y P L A N E M A K E R S 231
The mol di ng profile is scri bed on the toe and heel from a wooden tem
pl ate. For some profiles, the mol di ng i s "sprung" or angl ed for a more
consistent throat, as can be seen on the ol d mol di ng pl ane on the l eft.
Ted shapes the sol e profi l e to the layout l i nes with hol lows and rounds.
232 C H A P T E R T W E L V E .
The vari ous wooden templ ates shown in the foreground speed l ayout,
whil e the metal scrapers at rear are used to fine-tune the sol e profile
after it has been shaped wi th other mol di ng pl anes.
Commerci al pl ane makers shape the sol e with a "mother" or backi ng
pl ane with a mi rror-i mage sol e profi l e.
To lay out the profile for cutting the
sole, Ted uses a wooden template against
the toe and heel (see the top left photo
on the facing page). Interestingly, the
layout lines are not square with the sole,
but at an angle to it (known as the spring
angle). Springing the profile places it
more horizontal with the sole and gives a
more uniform throat opening, which
reduces the risk of tearout. (For more on
spring, see pp. 188-189. )
Commercial plane makers cut the
throat and wedge mortise next, and the
sole profile after that. Ted prefers to
profile the sole first, to make sure he gets
it right before any further cutting. He
cuts the sole profile with molding
planes, specifically hollows and rounds
(see the bottom left photo on the facing
page). Deep profiles are roughed out
with a plow plane by plowing one or
more grooves to a specific depth to guide
later cuts. The sole is finished with a
scraper ground to the molding profile.
Ted clamps the stock in a special jig that
holds it either upright or on its side for
the different cutting operations.
Plane makers doing production runs
of specific profiles use "mother" or
backing planes to cut the sole (see the
bottom right photo on the facing page).
They look like the same molding plane,
except that they have a mirror-image sole
profile. The new profile is shaped by
merely planing it on with the backing
plane. The same backing plane can be
used to create more complex molding
profiles by using it along with special
molding planes that add such details
as beads.
Once the sole is shaped, the mouth,
throat, and wedge mortise are cut next
(see the top photo at right). Using a fine
backsaw, Ted saws along the lines
defining the mouth and throat, stopping
just shy of the fence and base of the
handhold. With a fine chisel he chops
The mouth and t hroat of the plane are cut with a fine backsaw and then chopped out with a
chisel . The pi tch board in the background is for l ayi ng out the throat openi ng.
After defi ni ng the
wedge morti se and
then bori ng t hrough
to the throat, Ted
uses fl oats and
chi sel s to enl arge
the morti se and true
the bed.
C O N T E M P 0 R A R Y P L A N E M A K E R S 233
out the waste and deepens and refines
the throat. The wedge mortise is first
defined by chopping it about ':in. deep
and then boring through to the throat
with a small-diameter bit. To refine the
mortise Ted uses a narrow chisel and
floats (see the bottom photo on p. 233).
Fl oats are pl ane
maker' s tool s, a
cross between a
rasp and a chi sel ,
that cut smoothl y
and qui ckl y. Many
floats are made
from ol d fi l es.
The wedge for the
pl ane i s cut from a
pattern in a shape
di sti ncti ve for each
pl ane maker. The
iron is forged from a
bl ank cut from an
ol d ci rcul ar saw and
fi l ed to the sol e' s
profi l e.
234 C H A P T E R T W E LV E
Floats are special plane maker's tools that
are a cross between a rasp and a chisel
(see the top photo below). It's most
important that the bed line is true right
into the throat. Ted uses a pattern wedge
to check the dimensions and then to cut
a wedge for this plane.
For the iron, Ted cuts up a section of
an old heavy circular saw (sawmill sized).
He forges the blank into the distinctive
molding-plane iron shape, tapering
thinner away from the cutting edge and
with a long narrow tang (see the bottom
photo at left). He fits the iron to the
plane and checks that the wedge secures
it well close to the cutting edge. If
necessary, Ted improves the fit by
twisting the iron slightly or hollowing
the bed. The next step is to shape the
soft iron to the sole profile with a file.
After hardening and tempering it in the
forge, Ted hones and refines the iron to
the exact profile.
The plane is now finished, except for
chamfering the edges to soften the hand
hold and refine the plane's appearance
and rubbing on a coat of oil to protect it.
Each plane maker's style is distinctive in
the way he cuts the chamfers and details
the finial on the wedge. Where once
molding planes made by hand had
pronounced details, over time some of
these disappeared as planes became more
uniform and plane making turned into
an industry. Ted Ingraham's plane shows
those handmade details. With only an
occasional honing of the iron, it will last
for years and years.
Leon Robbins:
Specialty
Wooden Planes
Leon Robbins, of Bath, Maine, came to
making planes after a career selling
antique tools and restoring furniture.
"I took the challenge to make one," he
explained, "but it wasn't easy."
Traditional methods frustrated him:
"I burned every other plane. " A deeply
religious man, he prayed about it and
one day had a vision about a different
technique. Today, almost 20 years later,
he is making a living turning out a steady
run of traditional wooden planes:
compass hollows and travishers for
chairmakers, panel-raising planes,
dovetail planes, coachmaker's planes,
miniature planes, and bench planes.
Although he loved the challenge of
making the planes, selling them was
hard. He had some contacts from his
years dealing tools to craftsmen and
collectors. He tried ads and a tool
distributor. A colorful old-timer in an
unusual business, it was just a matter of
time before Yankee Magazine and others
found him. Today he sells mostly
through Garrett Wade, Woodcraft
Supply, and by word of mouth.
To see his shop you would never
expect it to be a plane "factory." Compact,
with machinery, tools, and jigs packed in
everywhere, it feels more like a shop on
one of the ships built nearby at the Bath
Iron Works. He has two low benches
opposite each other for shaping and fine
tuning planes, and an old swiveling
office chair he rolls between them. As we
talked, he pulled out planes, tools, and
jigs to explain his method.
Most of his planes have a bench
throat, the kind of throat cut into the
center of the plane and quite different
from the side escapement throat on most
molding planes. This type of throat
requires a different construction
technique. Leon's frustration early on
was in finding a way to cut a consistent
throat in a solid-hardwood plane body.
Today he laminates the body out of two
thin sides and two center pieces-one the
bed and rear of the plane, the other the
toe and throat. Working this way lets
him control the width of the throat
more exactly; since the sides are most
visible, he uses eye-catching curly or
bird's-eye maple for them.
Leon Robbi ns makes tradi ti onal wooden pl anes. Shown here (cl ockwi se from top left) are a
mi ni ature bench pl ane, a panel -rai si ng pl ane, an unusual mol di ng pl ane, a compass hol l owi ng
pl ane, a rabbet pl ane, and a coach maker' s pl ane.
The center pieces and sides are cut
out on the bandsaw with jigs and then
trial assembled. On large planes, gluing
the parts together in perfect alignment is
the challenge, because clamping pressure
inevitably makes one or more parts
lubricated with glue shift. To prevent
this shifting he drills and pins the parts
together dry with very small dowels,
using a wedge in the throat to keep
things aligned. The pins are cut off later
when the body is trimmed to size and
the sole is trued. Lately, he's been
making a lot of compass hollowing
planes for shaping chair seats, a design
worked out with the help of chairmaker
Michael Dunbar. Leon shapes the
complex soles of these planes on a
sanding jig chucked in the drill press. He
cuts and shapes the irons for many of his
planes from hardened tool stock that he
buys from a specialty supplier.
What started as a challenge has
turned into a business that's growing
every year. When Iwas visiting him he
was filling an order for 1 25 planes-far
more than he can comfortably make
alone. He tries and fine-tunes each plane
until he's satisfied. Only then does it
leave his shop. I left with a sense that
even greater than the financial security
the business has brought him was the
satisfaction of making good tools that
others appreciate.
C O N T E M P 0 R A R Y P L A N E M A K E R S 235
Lie-Nielsen
Toolworks:
Re-engineering
Metal Planes
Although their makers live fewer than
50 miles apart, there is a world of
difference between Leon Robbins' hand
made wooden planes and Tom Lie
Nielsen's elegant metal tools. While they
are both making traditional tools, Lie
Nielsen Toolworks is re-engineering and
remaking some of the best of Stanley's
classic designs. Tom Lie-Nielsen is clearly
interested in redefining our perceptions
of just how good a new tool can be.
Tom Lie-Nielsen's whole life prepared
him for making planes. Still, he never
expected to end up as the driving force
behind a small Maine company making
the best modern production planes. Full
of the energy of someone obviously in
love with his work (he never takes stairs
at any less than two or three steps at a
time), Tom gave me a tour of his modest
factory while explaining the steps
involved from idea to finished plane and
how he ended up a plane maker.
He grew up among the wooden boats
and old-timers of his father's boat shop
in Rockland, a town or two away from
Warren where he lives now. It was there
that he learned woodworking skills and,
in the shop's small machine shop, how to
machine and fabricate boat hardware.
Tom learned casting by pouring a huge
lead keel in the beach sand behind the
shop. When he finally left and headed to
New York, he took with him the most
important skills that would later serve
him as a plane maker-the ability to
design and make things with his hands.
His time in New York taught him
more-what woodworkers wanted in the
way of tools. He ended up at Garrett
Wade, selling tools and dealing with
customers. They would lament that
236 C H A P T E R T W E L V E
Lie-Ni el sen Toolworks is redesi gni ng cl assi c Stanl ey pl anes. Thi s versi on of the Bed Rock #604
has a heavy body cast from manganese bronze for beauty, durabi l ity, and good performance
and a heavy iron and preci si on-made parts throughout.
"they just don't make it like they used
to," to which Tom responded that "we
have the technology, they just don't
care." Stanley, who long dominated the
industry with innovative and well-made
woodworking hand tools, had basically
written off the market. Although the
company was regularly turning out
30, 000 planes a week, producing a few
thousand specialty ones a year didn't
interest Stanley. Tom saw that the
interest in working with one's hands and
woodworking in particular was growing.
There was another key to the
woodworking hand-tool market that
Tom quickly realized. Used tools were
plentiful, but for all but the most basic
planes (#4s, for example), the market
seemed specialized and mysterious to
the uninitiated. If they were to buy an
older tool, what was a fair price, would
the quality be okay, and would it be
usable? To buy new tools felt safer.
By the time Tom left Garrett Wade,
he understood the woodworking tool
market well enough to believe there was
a demand for quality tools. It also
brought him into contact with Ken
Wizner, the maker of a bronze version of
the Stanley #95 edge plane. Ken wasn't
that interested in plane making and was
never quite able to keep up with
demand, so he gladly sold the business to
Tom. When Tom brought out the skew
block plane the following year, he was
still a long way from where he is today,
but he was making planes.
Designing and making the skew block
plane was trial by fire. Manganese bronze
(an alloy of mostly copper and zinc with
trace amounts of manganese and other
elements) was used for the casting. It still
is for all of Lie-Nielsen's bronze planes,
because it is strong Cit won't crack if
dropped as cast iron will), it holds up to
wear well, it is heavy and doesn't rust,
and, maybe most important, it has a
beauty and warmth that are hard to
resist. After it was cast, machining the
skew block plane involved the challenges
of milling compound angles and holding
odd shapes. The first year he made only a
couple hundred planes and sold them all
through Garrett Wade. Gradually new
designs were added, as well as more
machinery and some employees.
A low-angle block plane and a jack
plane followed. All were specialty
designs, long since dropped by Stanley.
The Stanley # 1 was the next step,
because, as Tom tells it, "I wanted to
experience what goes into making bench
planes." The # 1 involved learning how to
make a large number of identical parts,
chip breakers, and handles, all nearly
miniature in size. From there the Bed
Rock bench planes #602, #604, and
#605 followed.
The dozen or so designs in production
today are all based on classic Stanley
patterns. A question that comes to mind
is what about the patents that Stanley
had on most of their tools and even
specific parts of some, such as adjusters
and lever caps? What Lie-Nielsen is
doing is no different than what other
manufacturers did a century ago. As
patents expired (they last only 14 years),
others readily borrowed the successful
designs. And while Lie-Nielsen's planes
are based on the same designs, the new
patterns are refined and re-engineered
beyond anything Stanley ever did. To
work better and more easily, plane bodies
are heavier, adjusters are designed into
planes that never had them, much
thicker irons are designed into every
plane, and all parts are machined and
polished to very high standards.
MAKING
BRONZE PLANES
To make cast-metal planes takes a
surprisingly modest amount of tooling
and technology. It shouldn't be
surprising, given that cast-metal planes
have been made for over 1 50 years, well
before Bridgeport vertical mills or
computer-driven machine tools were
invented. The steps involve casting the
body and body parts; machining the
throat, sale, sides of the body, and all of
the areas that mate with other parts;
machining and polishing the parts; and
assembling them all together. Although
it might not be high tech, making the
34 parts in a smooth plane, machining
them accurately, and assembling them in
a high-quality tool is challenging. To be
efficient at it and be able to produce
affordable tools makes it more
challenging still.
At Lie-Nielsen Toolworks, raw
materials literally come in the back door,
move through the various departments
as they are cast, machined, and finished,
and move out the front door as
completed planes. What I didn't expect
is how raw the materials actually are
ingots of bronze, brass and steel rods, flat
bar stock for the irons, and cherry planks
for the knobs and handles (see the photo
below). Of all the parts on the #604
bench plane, for instance, only two small
Phillips-head screws aren't made right on
the premises.
Well before the casting or milling
comes the careful designing of each tool.
This involves the skills of a patternmaker,
who makes a wooden pattern and mold
of the tool. The pattern is essentially a
wooden version of the plane; each part
requires a separate pattern. It's more
complicated than that, though, because
the hot metal shrinks as it cools. Some
To control qual i ty,
al most every part of
every pl ane is made
i n Lie-Ni el sen' s
smal l factory from
raw materi al s
i ngots of bronze,
brass, and steel
rods, flat bar stock
for the irons, and
cherry pl anks for
the knobs and
handl es.
C O N T E M P 0 R A R Y P L A N E M A K E R S 237
metals shrink more than others-cast
iron less than 1 % and bronze about 4%.
The wooden pattern has to account for
this shrinkage. Then there is something
called "draft," which is the taper built
into the parts so that the plastic pattern
made from the original can be more
easily removed from the sand when
making the sand mold for casting.
Beyond this, the patternmaker also has
to design the patter so that it can be
cast well and not leave thin sections
incomplete.
Plastic versions of the plane are cast
from the mold of the wooden pattern.
Depending upon their size, a number of
plastic planes are attached to what is
known as a matchboard, a 1 6-in.-square
wooden board. This is the pattern the
actual casting is made from. It's also the
patternmaker's job to lay out the path
that the molten metal takes. It enters
through a funnel-shaped sprue, flows
along the runner filling the cavity of
individual planes, and proceeds into gates
connecting the parts. Each casting also
has a riser, usually behind the thickest
part, that is a reservoir of molten metal
to help compensate for shrinkage.
Making the sand molds and casting
the metal is ancient technology. The
sand is a very special natural sand that
looks and feels like fine black loam. It has
to be fluffy to dissipate the air displaced
by the molten metal and moist enough
to hold its shape. The matchboard is
dusted with talc (to help release it from
the sand mold) and captured between
two halves of a mold that is filled with
sand and tightly tamped. Separating the
molds releases the matchboard and
leaves a void with exactly its shape,
complete with runners, gates, and risers.
The sprue is cut in, and the mold is
ready to be poured.
Depending upon the size of the plane,
only between a dozen and two dozen
planes are cast in one pour, in about six
238 C H A P T E R T W E L V E
molds. For smaller parts such as frogs
and lever caps, far more can be cast at a
time. The pour is a drama of intense
white heat and flowing molten metal.
The entire vessel holding the golden
liquid bronze glows a bright orange
when it's pulled from the furnace. There
are no flying sparks, only the quiet
concentration of two men pouring the
metal as consistently as possible. Just a
short while later the molds are knocked
apart and the process is started again.
From the time the individual planes
are cut apart until the plane is boxed and
shipped, every pair of eyes is checking for
quality. A slight pit in the casting, an
asymmetric shape, a surface not perfectly
milled-almost anything can send a plane
back to the foundry. The acceptable
castings are stress-relieved in an oven, for
Pl ane bodi es and
other parts are cast
in smal l batches i n
tradi ti onal sand
mol ds. The heavy
bars atop the mol ds
prevent the sand
from buckl i ng as
the molten metal f i l l s
the mol d.
As each rough cast
i ng passes through
the machi ne shop
gett i ng its body
mi l l ed to si ze, i ts
sole ground flat, and
its throat opened,
operators constantly
check tol erances
and qual ity.
just the same reasons that wood is
seasoned before it can be reliably milled
and worked.
From the foundry the planes pass
through the machine room. Using old
Bridgeport milling machines and a
handful of computer-controlled lathes
and vertical mills, all of the important
surfaces of the casting are machined. The
throat is opened, the bedding surface of
the frog is milled, the sole and sides are
surface-ground flat, and holes are drilled
for such things as frog screws and rods to
secure handles. A steady stream of lever
caps, adjuster yokes, frogs, and many
small parts is also moving through.
Plane irons are among the parts in
motion. Lie-Nielsen irons start out as bar
stock, which is cut to length, shaped, and
beveled. Their irons are good not because
they use the best steel (there are more
expensive alloys available), but because
they take great care with the next step
tempering. The irons are hardened in
small batches in a salt bath, a vat of
molten salt about 1 , 500 F, and
quenched in a S S-gal. barrel of water.
It's the same process as hardening steel
red hot with a fire, except that it's far
more predictable. From there the irons
go into an oven to draw the temper. The
hardening warps the irons slightly. They
are surface-ground flat, the edges are
trued, and the bevel is ground and,
finally, honed by hand.
All the while in the woodshop a crew
is turning knobs, shaping and sanding
handles, and stuffing the few planes that
require it. Another crew is grinding,
polishing, and hand-filing the completed
metal parts. In the machine shop, parts
such as lever caps are assembled. The last
step is bringing all the parts together and
assembling the finished plane.
By the time a Lie-Nielsen plane is
shipped, many eyes have looked at it
through the dozens of separate
operations that went into making the
parts. If one thing above all distinguishes
these planes, it's their high quality.
Everything about the way they are made
contributes to the quality-small
batches, manufacturing nearly every part
on every plane, and trying new
techniques to constantly improve the
finished prod uct. Very few of the best
tools wear out, except under the hardest
conditions and constant use. These are
some of the best tools, destined to last
many generations and give pleasure and
satisfaction to all who use them. To those
disappointed with the mediocre quality
of new tools, Lie-Nielsen planes prove
just how good a tool can be.
Jeff Warshafsky:
Modern Norris Planes
Jeff Warshafsky started making planes
out of frustration with both new and old
planes. While working with Ian Kirby
making furniture, he was introduced to a
Norris smoothing plane. It worked better
than any of his Record planes, but as he
told me, "I liked the plane, but not the
adjuster." Still, he went to buy one, they
were expensive, and "they all needed
work." So he set out to build his own and
improve on the original. Being
mechanically minded and an optimist
didn't hurt.
Luckily his brother, a manufacturing
engineer, guided him through the
difficult parts. Jeff made a mahogany
pattern and sent it off to have one iron
plane cast at a foundry. He milled all the
important surfaces on a small Bridgeport
machine while he thought about how to
redesign the adjuster. For the iron he
used a special alloy, cryogenically treated
to hold a keen edge (see the sidebar on
p. 240). Anyone familiar with Norris
planes, quite possibly the highest
evolution of the plane, will understand
something of the high standards Jeff
expected. Whether he succeeded or not
is a matter of opinion, but by then he
had the urge to keep making planes. "If
I'm interested," he thought, "then maybe
someone else is."
An ad in Fine Woodworking magazine
generated some sales. Jeff tried to sell the
idea to the larger tool catalogs with no
Reed Pl ane
Company made
four sizes of bench
pl anes. Shown
here are i ts heavy
bronze smoother
patterned after
si mi l ar Norri s
desi gns and a low
angl e bl ock pl ane.
C O N T E M P 0 R A R Y P L A N E M A K E R S 239
C RY O G E N I C S
I
f I told you that freezing
your plane irons is going to
make them take and hold an
edge a lot better, you might
not believe me. I'm not
exaggerating the results, but
there's a little more to it than
popping your tools in the
freezer. That is unless yours
happens to be set for -310 F.
Cryogenic tempering has
been done commercially since
the early 1980s. I first heard
To end up with a
fi ni shed pl ane free
of casti ng defects,
Jeff started wi th
oversized casti ngs
made from a wooden
pattern. After many
hours of mi l l i ng and
hand f i l i ng, the
pl ane body ( shown
i n the foreground)
was ready for i ts
wooden i nfi l l .
about it from a woodworker
friend who supercooled his
chisels with good results.
When I tried out the super-
cooled iron in a Reed Plane
Company's smoother, I was
convinced there was
something to it.
Cryogenics seems as much
magic as science. How else can
you explain a process that
gives musical instruments a
clearer tone or makes panty
hose last 6 months? Each simply, the edge lasts longer.
company has its own Microscopically, the austenite
technique, only adding to the component of the steel is
mystery. Essentially, for less converted to harder
than $2, you can have one of martensite. Easier to
your plane irons slowly cooled understand is to think of it as
to -310 F in liquid nitrogen. an extension of the heat-
It's held there for a day and tempering process, where
then warmed to 310F. What beneficial changes happen
you get back is an iron free of from a deeper " quenching."
stress, and while it's no harder,
it is permanently more
resistant to wear. Quite
the handwork making and fitting the
wood infill and adjuster, opening the
throat, and polishing everything. In the
end, he made a little over 1 00 planes
before Mahogany Masterpieces went out
of business. Jeff's life and interests
changed, too. He realized there was too
little profit to continue, but by then he
had the satisfaction of knowing he had
made many beautiful planes.
Jamestown
Tool Company:
Planes as Art
luck. It wasn't until he met Robert Major
of Mahogany Masterpieces that Reed
Plane Company really got going. Jeff
chose the name, by the way, because it
sounded quite fitting to a company
making English planes. Robert Major
wanted to sell Jeff's planes. He suggested
casting them from bronze, making
different sizes, and marketing them in
individually ftted mahogany boxes along
with shavings the plane had cut.
Jay Gaynor and Joseph Hutchins had a
similar romantic idea about making
English planes. Like JeffWarshafsky,
they had little experience. Joseph had
built some furniture and knew about
wooden planes and hand tools. Jay's
interest in tools was more as a historian,
as a curator of a tool collection. Not long
after they met they took over Jay's
basement, and, working evenings and
weekends with tools that were not
240 C H A P T E R T w E L V E
While it was exciting to be making
planes, it was demanding work. The
planes had to be perfect. Not so romantic
were the hours it took milling oversized
castings beyond possible casting defects,
particularly sophisticated, they built
planes as beautiful as any ever made.
As Joseph explained, "We attempted to
make tools as art in much the same way
that Spiers, Norris, and Mathieson did,
with shaped yokes and curving plane
sides beyond the functional." Over the
next three years they made about 50
planes in four patterns: a miter, thumb,
shoulder, and chariot plane.
Each described the adventure as
"diving into new things, learning
pattern making and all of the steps to
making a plane." There were a lot of new
techniques to learn. The first step was to
make a wooden pattern, based on planes
that they borrowed, and then urethane
castings of it (with glass beads to give the
body rigidity). A local foundry cast them
in bronze. They milled the inside
surfaces, sole, and sides, soldered on a
steel sole, and then began hours of hand
filing, fitting, and finishing. They had
help from some friends making guns
who advised them on finishing
techniques and how to inlay the wood
infill common on all of their planes.
What distinguishes Jamestown
planes is the care with which they were
finished. Finishing took as long as all of
the rest of the manufacturing. It's easy to
understand why. Every edge was shaped
with a file and sanding sticks and then
polished. Each tiny pit in the casting was
chiseled out, a small piece cut from scrap
from the same casting (each saved and
numbered in a box) was fit to it, and the
surface was peened over to make an
invisible repair. Screw slots were always
aligned parallel with the sole or with
each other (as seen on the chariot plane
in the bottom photo at right). This
meant using special fillister-head screws
and turning them in tight, marking the
screw slot, backing the screw out, milling
Jamestown Tool Company set out to make pl anes as art, as beauti ful as the tradi ti onal Bri ti sh
tools that served as patterns. They made four di fferent pl anes, i ncl udi ng the low-angl e miter
pl ane shown here. ( Photo courtesy of Jamestown Tool Company. )
it flat, filing a new screw slot, and finally
tightening it once again. Every detail was
important.
The final test for each plane was to
take an end-grain shaving from an oak
plank. The final test for Jamestown Tool
Company was that it was economically
unsuccessful. I dou bt that Jay and
Joseph ever really expected it to be. Far
more captivating was the romantic idea
of making planes patterned after some of
the most elegant tools ever made. Their
planes are a testimony to that vision.
Meeting these plane makers has
convinced me that making planes does
not have to be a dream. While there
might be a place for more small
companies like Lie-Nielsen Toolworks
making 10,000 or so planes a year, the
rewards can be just as satisfying making a
few planes for yourself. And who knows
where it might lead?
The careful al i gnment of the slots in the
screws that secure the adjustabl e throat
in thi s chari ot pl ane is typical of Jamestown
Tool Company' s attenti on to every detai l .
( Photo courtesy of Jamestown Tool Company. )
C O N T E M P O R A R Y P L A N E M A K E R S 241
B UY ING PLANES
Ifa tool appeals to me I keep it. After an it can always be sold tomorrow
or the day after!
-A collector commenting on the "squirrel syndrome"
Wen I think about buying planes,
my first thought is always of old tools.
Old tools appeal to many, but for
different reasons. Some, like myself, are
users. I like the feel of a tool worn by
some past craftsman-a tool rich with
history from an earlier age when hand
tools were deeply valued and each was
built with quality and care. Today, few of
the hundreds of different planes once
available are still being made, and sadly
most are not that good. Yet there is a
nearly endless variety of old planes to
discover, to tune for use, or to search
for-just for the pure fun.
Others love and collect old tools out
of curiosity. Some are attracted by the
beauty and variety of the tools alone.
Others feel a connection through the
tools to their trade and the working
methods once used. Tool historians and
others study tools to understand specific
trades, their traditions, and how tools
changed the work, and the work the
tools. As little as 30 years ago there were
few books about old tools, their makers,
and how they were used. Today, with
more collectors and more interest, our
knowledge has grown of how and why
many of these tools evolved.
Ol d tool s have a beauty and appeal that new tool s lack. Whi l e i t
woul d be hard to bui l d a boat wi th these tool s as the i nsi de l i d of one
of these boys' tool chests suggests, the tool s reflect the si mpl e beauty
of wooden hand tools.
Buying old tools to use is deeply
satisfing. One of the most astonishing
stories told to me recently by someone
selling new tools was how often he heard
people express fear about buying old
tools. Perhaps they imagine a fraternity
of dealers trying to get top dollar for
worn-out and less than usable tools. This
isn't entirely untrue; some of the most
expensive tools are a little worn out,
mostly because they've had long, hard
lives. But these aren't the tools you'll
want to collect to use anyway. Usable and
useful tools are to be found everywhere,
for prices often lower than new tools.
243
Every large flea market has someone sel l i ng tool s, or, in thi s case, the enti re fl ea market is tool s.
So many pl anes were made over the past 200years that you never know what mi ght turn up.
Bargai ni ng is part
of the fun at fl ea
markets.
244 C H A P T E R T H I R T E E N
This chapter is a guide to where to look
for good tools, what to look for and to
avoid, and where it can lead if you love
old tools a little too much.
Buying Planes to Use
When I first started collecting planes
over 25 years ago I asked Vern Ward,
one of the oldest and most respected
dealers, for some advice. By then I had
acquired the usual Stanley bench planes
and wanted to buy some of the more
specialized planes for my furniture work.
The market was still a little bit mysterious
to me; I wondered if I would pay too
much or get tools hard to tune and
actually use. His advice was to "( I 1 Buy
the best planes available. (2) Buy the
tools you love. (3) Look everywhere
from dealers, auctions, flea markets,
barn sales, wherever." It has turned out
to be sage advice.
Old planes are everywhere. Go to any
barn sale, flea market, or country
auction and you are bound to find at
least a few worn-out molding planes, or
quite likely a whole lot more. Most
common a re the planes that many trades
used: cast-iron bench and block planes,
and wooden planes like smoothers and
simple plows. Literally millions were
made through the 1 9th and mid-20th
centuries. Less common are planes for
specific tasks or trades, such as
coachmaker's, furniture maker's, or
cooper's planes. The most rare (and
expensive) are early planes, both wood
and metal, with early attempts at
patented or unpatented improvements,
or ones that were never made in large
numbers because they were very
specialized, proved unpopular, or were
expensive (the Stanley #9 block plane,
for example) The best planes of this last
category always fetch the highest prices.
Competing for all of these tools are
users, dealers, and collectors. Rarely is
there a pure distinction between them.
Dealers can be users and collectors, too.
Collectors become dealers when selling
off excess planes from their collection.
And a user can easily become a collector,
and then a dealer selling some of the
surplus. What hat any of them wears on
a particular day depends on the tool,
how much money they have in their
pocket, and how much discipline they
happen to have.
Where to look for planes depends
upon how much time, energy, and
money you happen to have. Common
and inexpensive planes can be found at
flea markets, yard and barn sales,
country auctions, and sometimes
antique shops selling things other than
tools. If you are looking for a #4 bench
plane, any of these sources will turn one
up at a reasonable price, but it will take
some energy and time. By just keeping
an eye out over the years I've found a
number of interesting planes where I
least expected. And while it's still
possible to find a rare tool for a bargain,
books and price guides have educated
more and more people to the value of
old tools.
For the less common and rare tools,
dealers and specialty auctions are the
best sources. This is the easiest and most
direct way to find the tools you're after,
but there are fewer bargains. Expect to
pay a price consistent with the market.
Buying from a dealer you get the benefit
of his advice and of establishing a
relationship that can mean other
desirable tools coming your way. Most
dealers will bargain or swap and keep
an eye out for tools you are looking for.
Some have tool lists they send out a
number of times a year for a fee.
Deal ers ar e a good source of al l tools, from
the common to the unusual , but expect to
pay the market pri ce. Thi s deal er speci al i zes
in mol di ng pl anes.
At any tool aucti on there's j ust as much of
the action i n the parki ng lot. Dealers and
"tai l gaters" sel l tool s from tabl es or ri ght out
of the back of thei r cars.
Some tool auctions include shows
that attract a wide array of dealers
showing some of their best tools and
hottest recent finds. This is the best
place to see and feel some of those planes
you have only seen in books and to talk
with other interested tool people. It's
why I jokingly refer to auctions as my
"continuing education} about tools. In
the parking lot there are often a huge
number of "tailgaters," either selling out
of the back of their car or from small
tables. The prices are competitive and
there are literally tons of planes to look
over. But it's at the auction that the real
excitement happens.
B U Y I N G P L A N E S 245
One of the fi rst
aucti oneers to
speci al i ze i n tools,
Ri chard Crane
attracts buyers and
sel l ers from as far
away as Engl and.
He has an annual
spri ng and fal l
show and sal e and
si x country tool
aucti ons i n hi s cow
barn i n Hi l l sboro,
New Hampshi re.
246 C H A P T E R T H I R T E E N
BUYING AT AUCTION
At most, something like $3 million
worth of tools pass hands every year at
auctions, through dealers, at flea
markets, and at similar venues. This is a
tiny part of the antiques market, barely
equal to the price of one Impressionist
oil painting. To understand all of the
players and forces coming together at a
tool auction, I talked with auctioneer
Richard Crane. Since the early 1 970s he
has been a major player in the tool
market, selling everything from box lots
of parts to the most expensive and rare
tools. Today he has an annual spring and
fall show and sale, and another half
dozen country auctions at his cow barn
in Hillsboro, New Hampshire. Dealers,
collectors, and users come from
throughout the United States and from
as far away as England to swap, sell, and
share stories.
Richard started selling tools almost by
accident. Some tools were in among the
lots at one of his country auctions, and as
it turned out he sold them for a high
price. Knowing a good thing when he
saw it, Richard found more tools to
auction, including some of his own.
When Lee Murray became a partner,
they auctioned off Lee's tool collection
(which filled a three-story barn) to avoid
any conflict of interest. It took buyers a
while to find them so far off the beaten
track, but they did. At auctions they sold
everything, or as Richard tells it, "If we
couldn't sell 'em, we gave 'em away"
That got people's attention. It wasn't
long before he specialized in tools and
gained a reputation for satisfied sellers
and buyers alike.
Tools come from all over. Lee Murray
travels to see collections the owner (or,
sadly, often the widow) would like to
sell. Rarely will dealers buy a large
collection, because of the large up-front
expense and the long time it might take
to sell it all. More tools come from
collectors trying to focus their collection
or to part with tools that no longer
interest them. The commission is a set
20%. Dealers with rare or special tools
put them up for auction in the hopes of
getting the best price, or use it as a place
to unload surplus tools anonymously.
And at any auction you'll find the tools
that are someone else's problem-maybe
just a bad buy, a tool with improper
parts, or a hardly noticeable repair;
whatever the reason, an auction is a sure
way to sell a tool quickly. Not knowing
what you are likely to find is part of the
fun of auctions, but it's also why the
advice "buyer beware" is often repeated.
Buying tools at an auction doesn't
need to be any riskier than buying from a
flea market or tool dealer, and it's far
more exciting. The only way to "know a
bargain when you see one," as Richard
describes it, is to educate yourself. He
suggests picking up a few books and
learning about the tools, and talking
with other collectors and dealers. At the
very least, before the sale carefully
inspect each tool you intend to bid on.
The more you know, the more likely
you'll get what you expect.
I was nervous and somewhat timid at
my first few auctions-most people are.
As with many things, there are certain
procedures, and each auctioneer has his
own style. Before every auction the tools
are arranged in numbered lots on long
tables. Most people look more than they
touch, so naturally at first I was reluctant
even to pick up many of the tools, for
fear of dropping something or damaging
it. One day I got up the courage to take a
plane apart to check its condition, to
check the frog, and to check for repairs
or cracks where they might be hidden.
Now I freely pick up and take apart
whatever tools interest me, even ones I
don't bid on.
At aucti ons you
never know who
mi ght be bi ddi ng
agai nst you-users,
deal ers, col l ectors,
and someti mes
even museums.
When it comes to bidding, it's a
matter of style and discipline. The surest
way to walk away satisfied (and not
kicking yourself for buying something
you don't really need for more than you
had hoped for) is to set limits at the
beginning. When I'm examining the
tools before the auction I write down the
most I'm willing to pay for each one that
interests me. Then I stick to it.
You're bidding against collectors,
users, dealers, even museums, each with
their own ideas about what a tool is
worth. A lot of things can affect what the
tools are worth on a given day. In
Richard's experience, "If the stock
market was up yesterday, I'll have a better
sale today (higher prices)." Collectors
always seem to have the most money to
spend. Two who want the same tool can
push the price to levels that will amaze
you. At auctions that attract dealers
from different regions, their bids reflect
what tools sell for back home, or what a
B U Y I N G P L A N E S 247
collector they represent is willing to pay.
Usually, watching the dealers will give
you a sense for the market price. They
expect to make a profit by buying low
and marking it up one-third to one-half.
Don't worry about scratching your nose
and buying a $ 1 ,000 ivory-tipped center
wheel plow, get into the excitement and
bid on something.
There are two other ways to buy
planes at auctions: through a dealer who
will bid for you on specific items
(whether you are there or not), and from
special auctions conducted by mail and
phone bid only. Dealers bidding for you
charge a small commission and will
even ship the tools to you afterwards.
The risk is buying tools sight unseen. For
a mailphone auction there is a catalog
with descriptions and photos of all of the
lots. Then through an ingenious system
(obviously thought up by a tool dealer),
you can call in up until the last day to
check on your bids and raise them as
you like.
THE INFORMED BUYER
The key to success in buying old planes
(or any tools for that matter) is to
educate yourself. It's easy to read the
short descriptions in a new tool catalog
and get a fair idea of what you are
getting. You know the plane will be
complete and in working order, or at
least you can send it back if it's not.
While some dealers and auctioneers will
take back unsatisfactory tools, more than
likely once you buy a tool, it's yours.
Quite possibly it's this fear that deters
some from the old tool market. It's
understandable; after all, who wants to
spend $ ] 00 on a plane and find out that
it's missing important parts or is
unusable for some reason?
248 C H A P T E R T H I R T E E N
When plane hunting I always carry a
reprint of the classic Stanley catalog # 34,
originally printed in 1 91 5. Every tool is
described, along with exploded drawings,
descriptions of variations between model
numbers, finishes, and dimensions, and
often an explanation of how the tool is
used. Carpenters and others would have
had this catalog tucked into their tool
boxes to read during lunch-and
daydream about new tools. There are
many other such reprints and texts
about tools, some of which can be
bought from dealers who sell books
along with tools. The bibliography on
pp. 258-259 lists some ofthese, any of
which are well worth the investment.
Experience also helps. For a long time
before I bought any expensive planes, I
asked a lot of questions and looked a lot.
I still can't tell a Bed Rock #608 type 3
from a type 6, nor do I really care, but I
can recognize if a plane is complete and
if the parts are roughly the same vintage.
The more valuable the plane, the more
you need to know. Planes obviously vary
widely in quality and styles, but even the
same models changed over time. Usually
the price will reflect seemingly small
differences, such as an added 4 in. in
length, a certain style adjuster knob, or
a frog factory-painted orange. Most of
these subtleties mean more to collectors
than to users.
To further illustrate my point,
imagine that I've put two planes in front
of you that look identical. Both are basic,
inexpensive homeowner bench planes,
The key to success
in buyi ng old tool s
i s educati on and
experience. Ask
questi ons, read
books, or bri ng
al ong a copy of a
repri nted Stanl ey
catal og, so that
when l ooki ng
t hrough a box of
tool s you' l l know
what to l ook for and
what to avoi d.
with simple modern lines and painted
gray-blue. One is a Defiance #3 and the
other a late-series Victor # 1 103. If you
saw them at a flea market, you would
expect to pay no more than $20 for
either. That's what the Defiance is
worth; the Victor is worth more than
$ 1 , 000. There would be no way of
knowing how valuable it is without
experience and knowledge.
Dealers are another source of
information and help. While they are
ultimately trying to make a living (or
support their own tool collecting), it's to
their benefit to help you learn about the
tools. They want you to come back and
buy more someday. Don't expect a lot of
help on tuning and using planes; most
know more about their history,
subtleties, and scarcity.
Patience is another key to plane
buying satisfaction. For the most part,
these planes are manufactured items
(some of them by the millions), and
another is bound to turn up somewhere.
Even the rare tools show up regularly at
the bigger shows and sales. Part of the
thrill of collecting old tools is searching
for them and waiting for the right one
to come along-one that appeals to you,
is in good condition, and is at an afford
able price.
WHAT TO LOOK FOR
AND AVOID
As a user starting out you'll likely be
looking for the basic planes-common,
functional bench planes. There are so
many that you'll be able to choose just
what you want, risk less than what a new
tool would cost, and get a premium
plane. The next step is buying less
common and more expensive specialty
planes, such as shoulder rabbet planes,
dado planes, scraper planes, and compass
planes. The third step, should you take
it, is collecting some of the rare and
In your search for planes, you' re apt to find everythi ng from the common to the unusual , from
standard cast-i ron bench pl anes to these wooden cornice pl anes.
costly planes such as a Stanley #9 block
plane, a #52 shoot board and plane, or a
Norris A5 smoothing plane. By then
you're verging on being a collector. If
you know how to buy a good #4 bench
plane, then the next steps just take more
experience, knowledge, and patience.
The first test is to pick up the plane
and just feel it in your hands. Not only
will this give you a sense of its balance,
but also of how the tote and knob feel.
Are they smooth and polished, or do
they feel loose, rough or chipped, cracked
or repaired? Part of the beauty of older
planes is the beautifully shaped and
polished rosewood handles. While loose
handles are no problem (see pp. 5 2-53),
I wouldn't buy a plane with cracked,
chipped, or repaired handles if I had a
choice. Such planes will be less
expensive, but making or buying a new
tote or knob will take time and add to
the cost. And when it comes time to
resell, a repaired or replaced handle
devalues the plane.
Look the whole plane over. Does it
look complete? Bench planes are fairly
simple to evaluate, but when buying a
rabbet plane, for instance, empty
threaded holes will clue you to a missing
depth stop or fence. Do the parts look
natural together? Look for cracks and
chips, especially around the throat.
Grime coating a plane can conceal
cracks. Hearing a hollow ring when you
rap the body with your knuckle might
indicate a hidden crack. Chips devalue
the plane but, except for ones along the
throat, don't affect the performance.
However, chips along the sides that your
hands will rub against while using the
plane are uncomfortable.
Inspect the sole for wear and bad
scratches. Most used planes (and new
ones, too) are going to need some lapping
to polish and true the sole, so expect this.
B U Y I N G P L A N E S 249
P L A N E S T O B U Y F O R T H E S H O P
T
he planes listed here are useful in
nearly any woodshop for a wide
range of work. The Stanley numbers
refer to specific planes commonly
available or can be used to compare sizes
with planes by other manufacturers.
Many of these planes are available new.
All of them can be found in the used
tool market with a little luck and
patience.
The list is very flexible and should
be used as a guide only. What planes are
useful to you ultimately depends on the
kinds of work you do. Every craftsman
should have at least one of the first six
types; the rest can be bought as you
need them.
Bad scratches can be lapped out, but
they are rarely too deep to cause
problems. I try to carry a straightedge
with me to check the sole for flatness,
nevertheless. Often the seller will have a
square handy. Hold the plane up to the
light and sight under the straightedge as
250 C H A P T E R T I I I R T E E N
Block plane, a #60 Y2, #9 Y2, or Lie
Nielsen low angle
Smooth planes, #4 size for rough
smoothing and a heavy, finely made
plane such as a Norris-type Bed Rock
#604 or #60411 or a Lie-Nielsen #604
for finish smoothing
Jack plane, #5 size
Jointer, # 7 or #8 size
Rabbet plane, a basic bench rabbet
#78 or a heavier #289 with a skewed
iron
Hand-held scrapers, square and
"gooseneck"; and #80 cabinet scraper
(or similar handled scraper)
Router plane, #71 or #271
Two spokeshaves (straight and round
soled)
Shoulder rabbet plane, #93 or #92
(either also functions as a small chi sel
plane)
Bullnose rabbet plane, # 75, #90, or a
beautiful British example by Preston
or others
Bench rabbet plane, # 10 or # hY2
(smaller version of # 1 0 and more
scarce)
Narrow dado plane, #39Y4 or #39
3/8
or a wooden version
Chisel plane; the small Lie-Nielsen
version of the #97 is a wonderful tool
described in Chapter 4. The truer the
sole, the less work it will take to tune
the plane.
With the plane still assembled, move
the adjusters (if there are any) to see if
they work smoothly. Rotate the depth
adjuster through a wide range to feel for
Medium-diameter spoke pointer and
a simple pencil sharpener
Side rabbet plane, # 79, or #98
and #99
Miter plane or low-angle heavy plane
for shoot-board work
Scrub plane, or retuned smooth or jack
Various sizes of side bead planes
|'.-in. ,
1
/4 in. , /in., and 12 in. ), or #45
combination plane
Range of wooden molding planes,
hollows and rounds (three or four sizes
of each)
Beading tool, #66 with cutters
Compass plane, # 20 or # 1 1 3
Chamfer plane or shave, any pattern
Although I don't own one myself, many
craftsmen rave about the Lie-Nielsen
low-angle jack plane. They recommend
putting it near the top of the list.
Planes best for children
For the youngest kids, a finger plane
#201, # 1 01 , or # 100
Block plane, # 1 02 or Lie-Nielsen low
angle (basically the same plane)
Spokeshave or set of inexpensive small
bronze spokeshaves (three)
Bench plane, # 2 or # 3 size
any looseness or roughness from
damaged threads. It's rare that the cast
yoke capturing the brass adjuster wheel
is broken, but check it all the same. If the
plane looks good so far, take it apart.
First look at the frog and the setscrews
that secure it to the sole and, on planes
that have it, the screw that adjusts the
frog's position. It helps to have a
medium-sized flat-head screwdriver
handy. Rust covering the frog or screws
indicates the plane has been sitting in a
cellar or unheated garage long enough
that the screws might be frozen. Try
turning the frog adjustment screw first
to see if it's free. If you want to be very
thorough, check that the frog setscrews
are not frozen or stripped. If you get this
far, you might as well remove the frog
and inspect it. It will need a thorough
cleaning, but is it complete and
unchipped? Check that the screw that
holds the iron and lever cap in place is
free, not bent, and that the head is not
damaged.
What do the lever cap, cap iron, and
iron look like? Irons are replaceable and
often were. If there is less than about an
inch of iron left before the slot, it will
need to be replaced again before too long
if the plane is used a lot. The steel is
sometimes soft close to the slot, too.
Most irons will be discolored with a
slight amount of rust, but definitely
avoid an iron with a rusty back or one
that's noticeably pitted. Such an iron
will take hours of lapping and even then
not sharpen well. Neither the cap iron
nor the lever cap should be too rusty,
chipped, or deformed, but, like the
iron, these parts can be replaced if
need be (though not always easily or
inexpensively). The locking lever on the
lever cap should work smoothly. Check
that the screw that secures the cap iron
to the iron is not stripped and that the
slot in the head is not too badly worn.
I wouldn't worry about the cap iron
fitting the iron, since few craftsmen
either knew about or took the time for
this important tuning step.
Before you buy, i nspect the pl ane caref ul l y for cracks and mi smatched or mi ssi ng parts.
There are other subtle things to check
for that increase the plane's value. Is the
plane complete with original parts? This
is sometimes impossible to tell without a
lot of experience, because even at the
factory older parts were sometimes fitted
to the newest model. My Stanley catalog
helps here, but I also look for consistent
patinas and matching patent dates (if
any) on the iron and plane. Look at the
japanning, the black "paint" covering the
unmilled areas of the casting. Japanning
in fine condition adds to the plane's
value, although it in no way affects its
use. The finer the overall condition of
the plane, the higher its value now and in
the future.
Inspecting potential planes will take
some time, but it will further your
experience and help you end up with
some satisfying tools. While most
problems are repairable, you'll have to
weigh your skills, the amount of time
you want to invest in making the plane
right, and the di fference in price
between it and a perfect tool. The least
expensive tools can sometimes become
the most expensive.
If you like a tool, buy it. Among my
many regrets are the tools I for some
reason passed up. I can remember many
of them, including a mint-condition
Bed Rock #607 that was sold when I
returned from a brief walk to "think it
over." This isn't to say you should buy
everything you like; few of us have those
kinds of resources. But it's not always
true that a better tool will come along for
a better price. Except for the more
common Stanley planes, most tools are
different enough that some have more
appeal than others. Meanwhile you have
missed out on all of that time using and
enjoying the one you passed up.
B U Y I N G P L A N E S 251
REPAIRS AND
CLEANING
There's an ongoing debate among
collectors about cleaning and repairing
tools. One side feels that tools should be
left as found, with only the slightest
cleaning where really necessary. The
other side believes that tools should be
restored and cleaned to an as-used
condition, typical of a craftsman who
cared for his tools. One thing both
sides do agree on is that overcleaning
ruins a tool's historic, aesthetic, and
monetary value.
Since I am buying tools to use, I
naturally favor cleaning and repairing to
the point the tool is functional. As users,
we are less likely to buy rare or
historically significant tools (such as
early molding planes), both because they
are usually vastly more expensive and
because they are not always the best tools
for the work. For rare tools such as these,
I favor only the most necessary cleaning.
A complete cleaning runs the risk of
removing tool marks showing how the
plane was made and the beautiful patina
that only comes from years of handling
and use. Stick to working by hand, with
mild solvents and fine abrasives, and
you'll run little risk of overcleaning.
Cleaning a plane is part of its hidden
cost. I usually start by taking everything
apart. I clean wooden parts with very
fine steel wool (0000) and turpentine, or
kerosene for really thick grime. Usually
a thorough rubbing will clean off the
dirt and leave the patina, but sometimes
I have to lightly scrape a paint splotch or
dried-on glue. For a finish coating I use a
mixture of boiled linseed oil and beeswax
melted together (to the consistency of
warm butter), which I rub on and buff
off. Wooden planes finished with linseed
oil alone and stored in a damp place run
the risk of molding badly, since the oil
actually feeds the growth. A polish of
252 C H A P T E R T H I R T E E N
shellac is fine, but generally you shouldn't
use varnish.
I clean and finish metal parts that are
not too badly rusted the same way. A
slightly coarser steel wool removes more
serious rust. On parts such as the lever
cap and cap iron, I sand the working
edges with fine sandpaper such as 220
or higher. Fine wet-and-dry paper and
kerosene as a lubricant work well for a
final polish. Avoid overcleaning any brass
or gunmetal parts because it's easy to
leave the patina splotchy and remove any
protective varnish. A wipe of the linseed
oil and beeswax finish brightens any
japanning.
Repairing the boxing on a molding
plane or making other wood repairs can
be challenging, but it is rewarding,
especially if the tool is a bargain. Yet
metal repairs can quickly become beyond
the skills of the average craftsman. I
would avoid most tools that need such
repairs in the first place, but occasionally
you'll find a rare tool that's quite
Repai ri ng cast iron
takes experi ence
and great ski l l to
do wel l and can be
qui te costly as a
result. These three
repai rs are of vary
ing qual ity.
reasonable and worth repairing. It's very
tricky to weld cast iron, especially where
the material is old and thin. There are a
few specialists who do it; ask some of the
bigger dealers and collectors for
recommendations. When you figure in
that even the most basic repair can be
$ 1 00 or more, perhaps the plane isn't
such a bargain after all. And, remember,
even the most skillful repair is going to
devalue the plane somewhat and make it
harder to sell to someone other than
another user or impetuous collector.
Another downside is that it might not
work as well as it could. The alternative
is to keep looking and find a "parts"
plane to replace the damaged part.
Investing in Tools
When you spend hundreds of dollars on
individual planes, you can't help but
wonder about their value, say 10 or 20
years down the road. If you heed Vern
Ward's advice to "buy the best," you have
little to worry about. While some would
disagree about the value of buying tools
purely as an investment, historically the
high end of the market has grown
consistently. As users, we have another
distinct advantage to buying fine old
tools. What other things can you enjoy,
make a living with, and then sell for
considerably more than you paid?
When pressed about investing in
tools, auctioneer Richard Crane opines
that the value of tools has risen about
20% a year. Others think that this is far
too optimistic for all but the very best
and rarest items. Driving the market is
the underlying fact that there is a finite
number of old tools. For some of the
rarest of these, maybe only one or two
survive. As for the most common tools, a
Stanley #5, for example, there might be
millions still around. Prices are always
going to reflect the basic law of supply
and demand.
Richard likes to think of the tool
market as a stock market, with each type
of tool-levels, saws, planes, edge tools,
rules-as individual stocks. Some years
planes are hot, other years it could be
levels or saws. "Buy some of each," he
advises, "hedge your bet." The same
advice applies to any collection,
especially one where the investment
potential is even being considered. A
collection that's too narrowly focused,
say, one of shipbuilder's spar planes,
might be valuable to you (and costly to
acquire) but be worth far less auctioned
off all at once.
Prices reflect only what someone is
willing to pay. Auctions most specifically
establish values that day and sometimes
indicate where the market is headed.
Lots of factors drive the market and
establish prices, such as the number of
new and old collectors, their disposable
incomes, the quality of the tool-even
such factors as a tool's size. Larger tools
are not always so appealing because they
are hard to move and display. Subtle
things like an original box or a clear
maker's mark can increase the value of a
plane two times or more.
The reality is that for most of us tools
are not the best investment. It's hard to
make much money when the non-dealer
collector or user has to buy at retail and
sell at wholesale. The price has to
appreciate quite a bit just to break even.
The market is just too small and
specialized. But then there are the
stories-nearly every dealer has one-of a
flea market find that turns out to be
worth thousands. Richard Crane told me
of the " clunker" of a molding plane he
bought from a woman at a flea market
for $50. It turned out to be a signed
cornice plane worth $3, 800. I've heard
about yard-sale Stanley # 1 s bought for
$ 1 5 and early plow planes worth many
thousands bought for $300. Certainly
these kinds of tools can make you some
money, but it's more often due to
someone's knowledge of the tools and
labor in bringing it to market, not a true
"investment."
I still feel that tools are a worthwhile
investment for some. They might or
might not be growing in value as fast as a
CD, but the ones I own and use in my
work give me a different kind of pleasure
than money in the bank. It's the same
feeling expressed to me by another
friend and collector: "I often think that if
my addiction had been horse racing
instead of tools, I might easily have had
as good a time, but would have a whole
lot less to show for it. In that sense I
suppose you could argue that tools are a
good investment."
An ori gi nal box greatly i ncreases the val ue of any pl ane. To fi nd the ori gi nal box for a rare
pl ane, such as many of the ones shown here, is even more val uabl e.
B U Y I N G P L A N E S 253
A few of Scotty
Carter' s mi ni ature
pl anes are bench
pl anes, si mi l ar i n
every detai l t o ones
l i ke the brass-sol ed
smoother i n the
rear. The l arger of
these mi ght be a
sal esman' s sampl e.
Collecting Planes
Whether or not you call i t an investment,
it's still easy to buy a few planes, and
then a few more, and before you know it
you're collecting. Perhaps you're the user
who buys some planes to build that
Queen Anne highboy you've always
planned on making "someday." The
process can be so subtle that, before long,
planes fill every vacant space in your
shop. Some of us take Vern's advice to
"buy the tools you love" too far.
Every collector has his own stories
about how he got started, the first plane
he bought, or the rare ones he found in
unlikely places. Yet one of the funnier
quirks I discovered among collectors is
how many carefully follow every
movement of tools they would like to
own someday. More than one collector
discouraged me from photographing a
rare tool, saying it would only revive
interest and generate more phone calls.
Still, for the rarest of the rare tools, you
254 C H A P T E R T H I R T E E N
can bet that a number of people know
where they are and the chances of
getting them. Some wait years. Collecting
takes patience.
Collecting also takes judgment and
discipline. Few of us have the resources
to buy every plane we like, nor would
such a collection be very interesting.
Some of the finest collections I've seen
are modest, but they showed consistency
and judgment. The collection is an
extension of the collector's interest not
only in the tools but also in their history
and the society that created them. Most
never imagined where collecting a few
planes would lead.
SCOTTY CARTER,
COLLECTOR
It's fairly obvious at any tool show or
auction that nearly all the buyers and
sellers are men. Tools from the trades
have always appealed more to the
masculine half of the population,
probably because of man's long history
of designing, making, and working these
tools. In England there are a few woman
tool dealers, but here the few women
you'll notice are wives helping to run the
business and peddle the tools their
husbands are busily out buying and
swapping for. Scotty Carter stands out in
this crowd-as a dealer in high-end
English (and some American) tools, as a
long-term collector of miniature planes,
and as the white-haired grandmother
she is.
It was in her and her husband's shop
in Portsmouth, New Hampshire, that I
saw my first Norris plane many years
ago, long before I appreciated what they
were or could even afford one. I would go
down into her tool cellar and buy a few
English molding planes or carving tools.
She always stocked an incredible variety;
they were good tools and inexpensive.
She is still in the same shop, a restored
brick and granite grain-storage
warehouse overlooking the waterfront.
Since her husband, an avid and early
collector of New Hampshire tools, died
in 1983 she has run the business alone.
She still travels to England a cou pIe of
times a year to buy tools-finding a few
Norris smoothers or shoulder planes
among the more usual planes, chisels,
and saws.
With all of the beautiful tools passing
through her hands over the years, the
only ones she has been tempted to collect
are miniatures, planes no longer than an
inch or two, made from beautiful
materials and complete in every way.
Since she bought her first one in 1965
for $ 1 2, a tiny whale-shaped horn plane
lying on a blanket at the Amsterdam Flea
Market, she has collected perhaps two
dozen. "They're no different than other
antiques that appeal to you graphically or
for their form," she explains. And as
more than one collector has admitted,
"You don't know you are collecting until
one day you realize that you are."
S T O R I N G A N D D I S P L AY I N G P L A N E S
part of the joy of owning most simple shelves or even
and collecting fine tools is drawers can show off your
showing them to others. Even tools handsomely.
the most simple or basic tool As a user, I want the tools
can incite curiosity and I need accessible. I store large
interest. Many of the people planes on the wall right next
who visit my shop comment to my bench; a few are on
on how seldom they see a shelves, but most are arranged
craftsman at work, let alone in a bank of drawers just for
the variety and beauty of the planes. The smallest are
tools involved. And I have housed in shallow drawers
just a small and specialized with dividers. Medium-sized
collection. While glass planes and ones not needed
cabinets might be nice, the that often fill the center
Si mpl e shelves organi ze a col l ecti on of pl anes, keep them accessi bl e,
and show them off, too.
drawers. The large bottom surface rust. Wooden parts or
drawer is filled with molding whole planes can mold or be
planes on end just as they ruined by damp storage. Even
would have been in the a dry place exposed to big
bottom of a carpenter's tool swings in temperature, can be
chest. Everything stays dust- damaging. Metal cooled by a
free and organized. chill night will condense a fine
Dampness can ruin a good layer of moisture on it as the
plane. In a heated shop such as day heats up, causing rusting.
mine, rust is never a problem. The best place to store any
Other tools are not so lucky. tools is in a heated building or
It's common to find planes one massive enough to change
with pitted soles and irons, or temperature slowly.
at least covered with a layer of
Drawers are an alternative for dust-free and effi ci ent storage. They
need to be desi gned to take a l ot of wei ght and to fi t planes of various
di mensi ons.
Her complete collection is spread
on a piece of black velvet laid out in the
bottom of a low carton that once held
four six packs of some soft drink. The
display might not be elegant, but it's
obvious that she gets a great deal of
pleasure from each tool as she picks
them up to show to me. "They don't
show up anymore," she laments. She
remembers where she got each one or
the different dealers who gave her
certain special ones. With her warm
charm it's easy to imagine the friends
she has made dealing tools over the
years. Some planes are obviously usable,
molders made to shape some profile
such as curved window mullions (see the
bottom photo on p. 1 87). Others are tiny
bench planes for working in tight places,
and a few resemble salesman samples.
All are craftsman-made, needed for some
B U Y I N G P L A N E S 255
I ntri gui ng objects
onl y an i nch or
two l ong, these
mi ni ature pl anes
are beauti ful l y
made from beech
and boxwood.
fine work where no commercial planes
were available. As far as she knows, only
the English maker Edward Preston made
small planes, though they were larger
than most of these. Looking at them I
was awed by their precise workmanship
and felt the lure we all feel for small,
exquisite objects.
AN ADVANCED
STANLEY COLLECTOR
Scotty Carter's small planes would
disappear with hardly a trace into a
Houston collection I visited a couple of
months later. I had met this collector a
few years before at a tool show when I
was intrigued by the small number of
extremely rare (and expensive) Stanley
tools he was offering for sale-a hand
beader, #4 VzH, and a blind nailer. In a
thick southern accent, he described
himself as an advanced Stanley collector,
but this in no way prepared me for his
256 C H A P T E R T H I R T E E N
collection. What I found was a Texas
sized array of tools-planes, braces, rules
and measuring instruments, levels,
plumb bobs, tool parts, and related
memorabilia, such as trade signs, store
displays (many with original tools),
and catalogs.
The collection is mostly housed on
the top floor of a small office building
that at one time was used for grading
cotton samples from bales traded at the
nearby Cotton Exchange. Half the floor
is living space-a harmonious and
eclectic mix of pre-Columbian figures,
Thonet bentwood furniture, colorful
Art Deco lamps, modern Texas paintings,
religious icons, and glass cases filled with
small and special tool collections. The
other half of the floor includes a wood
working shop with a neat benchroom, a
small machine room, and a library
surrounded with old drugstore glass
cases filled with more planes and tools.
It didn't take long to realize the value
of this tool collection, both monetarily
and for its breadth and completeness.
Whole sections of shelves displayed
examples of highly sought # 2 bench
planes, showing the subtle changes in the
Stanley line and comparing them with
similar tools made by Ohio, Sargent,
Chaplin, and others. Some shelves held
one-of-a-kind Stanley prototypes or two
of the only three known examples of
certain tools. The same thoroughness
and rarity was represented in all parts of
the collection.
This collector (who requested
anonymity) grew up in Jackson,
Mississippi, into a very old family, the
son of a doctor and avid collector of
medical paraphernalia. It was from his
father that he inherited a passion for
collecting, or "shopping" as he now calls
it, and an awareness of tools and
woodworking. He remembers being a
typical boy, "drilling my father's auger
into the dirt and planing the sidewalk"
Gradually he started collecting good
tools for his own use-planes, levels,
rules, and whatever caught his eye-yet
with less discipline than he wishes he
had then or now.
He collected by buying from dealers,
from auctions throughout the United
States and England, from parking-lot
swap meets and flea markets every
where, all the while refining his high
speed shopping technique. From his
experience and careful study of the tools
he can recognize an overlooked part of a
scarce plane in a 50-cent box of rusty
screwdrivers and hardware. Looking for
highly sought after tools in original
boxes, he has gotten his foot in the door
and into the cellar shelves of more than
one hardware store by asking for level
bubbles. "But I had no discipline," he
freely admits, and he bought quantity
over condition. Often he would ask
himself if he already had four, why buy
A Texas-si zed col l ecti on of everyt hi ng from the common to one-of-a
ki nd tools. Housed in gl ass cases are exampl es of #2s made by Stanl ey
and i ts competitors, early and unusual bl ock pl anes, rare Sargent
pl anes, and col l ecti ons of other i nterest i ng woodworki ng tool s.
I n the same Texas col l ecti on are Bal i nese pl anes, many carved i n the
shape of humans and myt hi c ani mal s. Curi ously, i t' s rare to fi nd any
wi th i rons.
another. He summed up his passion by
quoting his wife: {the thrill of acquisition
and the boredom of possession."
Where a passion for collecting can
lead was evident when we visited the
cellar (or (concourse," as they elegantly
call it in Texas). A huge area was stacked
with row after row of boxes, all neatly
labeled and mentally catalogued. Only
about half were tools, the rest were the
results of his wife's passion for collecting.
It seems he became a bit of a legend at
one of the local flea markets when he
bought an entire truckload of chicken
boxes, those heavy waxed boxes and lids
for shipping iced chicken parts. Each box
contained a dozen or more planes of
every variety: Bed Rocks, Baileys, #45s
and #55s, Sargents, Gages, and many,
many others. We joked about what
would happen to the tool market if all of
these and the rest of his collection were
auctioned off all at once.
His collecting goes on, as he searches
for rare tools, parts and complete planes
in the original boxes, and examples of
Stanley's present tool production to keep
his collection current. At one time he
almost bought the famous Studley tool
chest now in the Smithsonian. As he
talks about subtle differences between
tools in his collection, it's obvious that
much time goes into studying and
thinking about them, how they work,
and how designs evolved. Often he offers
help to other tool historians doing a
{type study" of specific tools, freely
lending parts of his collection or catalogs
from his archives. As a woodworker, he
understands and appreciates the tools
from a different perspective, although he
uses few of them in his real passion
turning beautiful large bowls.
Upon leaving I pressed him for advice
to others getting started collecting or to
those already caught up in the passion.
{Collecting takes discipline and
judgment," he advised, although
admitting at the same time that he has
less than he would like. As for investing
in tools, {Stick with CDs or stocks and
bonds and use your earnings to buy
tools. Too many men convince their
wives what a great investment they're
making and guiltlessly go out and spend
more money on tools." Luckily for him,
his wife is just as passionate a collector
as he is.
B U Y I N G P L A N E S 257
B IB LIOGRAPHY
Allen, Sam. Plane Basics. New York: Sterling,
1993.
Basing, Patricia. Trades and Crfts in
Medieval Manuscripts. New York: New
Amsterdam, 1990.
Bealer, Alex W. Old Ways of Working Wood.
Barre, Mass. : Barre Publishers, 1972.
Blandford, Percy W. The Woodworker's Bible.
New York: Crown Publishers, 1984.
The Book ofTrades, or Librar ofthe Usefl
Arts. Jacob Johnson Publisher, 1807.
Reprinted as Little Book of Early American
Crfts and Trades, edited by Peter Stockman.
New York: Dover, 1976.
Chinn, Gary, and John Sainsbury. The
Garrett Wade Book ofWoodworking Tools.
New York: Gallery Press, 1979.
The Cutting Edge: An Exhibition ofShefeld
Tool. Sheffield, England: Ruskin Gallery,
1992.
Dunbar, Michael. Restoring Tuning and
Using Classic Woodworking Tools. New York:
Sterling, 1989.
Garvin, James L. Instruments ofChange:
New Hampshire Hand Tools and Their Makers
1800-1900. Catalog of exhibition at New
Hampshire Historical Society, December 20,
1984-May 30, 1985.
Gaynor, James, and Nancy Hagedorn. Tools:
Working Wood in Eighteenth-Centur America.
Williamsburg, Va. : Colonial Williamsburg
Foundation, 1993.
Goodman, W. L. British Planemakers frm
1 700. 3rd. ed., enlarged and revised by Jane
and Mark Rees. Mendham, N.J.: Astragal
Press, 1993.
-. The Histor of Woodworking Tools.
London: G. Bell and Sons, 1962.
258
Graham, Frank D. , and Thomas J. Emery.
Audels Carpenters and Builders Guide # 1.
New York: Audel, 1946.
Greber, JosefM. The History ofthe Wood
working Plane. Translated by Seth Burchard.
Zurich: 1956. Reprint, Albany, NY: Early
American Industries Association, 1991.
Hayward, Charles. Cabinet Makingfor
Beginners. New York: Drake, 1971.
-. Tools for Woodwork. New York: Drake,
1976.
Hazen, Edward. Popular Technolog; or
Professions and Trades. New York: Harper and
Brothers, 1846. Reprint, Albany, NY: Early
American Industries Association, 1981.
Henry, Bernard. Des Metiers et des Hommes au
Village. Paris: Seuil, 1978.
Hibben, Thomas. The Carenter's Tool Chest.
London: George Routledge and Sons, 1933.
Hoadley, R. Bruce. Undertanding Wood.
Newtown, Conn.: Taunton Press, 1980.
Holtzapffel, Charles. Turing and Mechanical
Manipulation. London: Holtzapffel & Co.,
1875.
Jenkins, J. Geraint. Traditional Country
Craftsmen. London: Routledge and Kegan
Paul, 1978.
Joyce, Ernest. The Encclopedia of Furiture
Making. New York: Drake, 1 978.
Kean, Herbert P., and Emil S. Pollak.
Collecting Antique Tools. Morristown, N.J.:
Astragal Press, 1990.
Kebabian, Paul B. "A Rarity: The Shoe Peg
Plane." Plane Talk 1 1 (#4, 1987): 52- 53.
Kebabian, Paul B., and Dudley Witney.
American Woodworking Tools. Boston: New
York Graphic Society, 1978.
Kebabian, Paul B., and William C. Lipke
Ceds.) Tools and Technologies-America's
Wooden Age. Robert Hull Fleming Museum,
University of Vermont, Burlington, Vt.,
1979.
Kingshott, Jim. Making and Modifing
Woodworking Tools. East Sussex, England:
Guild of Master Craftsmen Publications,
1992.
Landis, Scott. The Workbench Book.
Newtown, Conn.: Taunton Press, 1987.
-. The Workshop Book. Newtown, Conn.:
Taunton Press, 1991.
Lee, Leonard. The Complete Guide
Sharpening. Newtown, Conn.: Taunton Press,
1995.
Mercer, Henry C. Ancient Carpenters' Tools.
5th ed. New York: Horizon Press (for the
Bucks County Historical Society), 1975.
Mowat, Alexander and William. A Treatise on
Stairbuilding and Handrailing Barrow-in
Furness, England: 1900. Reprint, Fresno,
Calif. : Linden Publishing, 1985.
Moxon, Joseph. Mechanick Exercises: or the
Doctrine ofHandy-Works. 3rd ed., London:
1703. Reprint, Albany, NY: Early American
Industries Association, 1975.
Newlands, James. The Carpenter's and
Jointer's Assistant. Edinburgh and London:
Blackie & Sons, 1860.
Nicholson, Peter. New Carpenter's Guide.
Improved and enlarged edition. London:
Jones, 1826.
Odate, Toshio. Japanese Woodworking Tools:
Their Tradition, Spirit, and Use. Newtown,
Conn. : Taunton Press, 1984.
Proudfoot, Christopher, and Philip Walker.
Woodworking Tools. Oxford, England:
Phaidon, Christies Ltd., 1984.
Rees, Jane and Mark. Tools, A Guide for
Collectors. Suffolk, England: Roy Arnold,
Ipswich Book Co., 1996.
Rees, Mark. liThe Lid of a Cabinetmaker's
Tool Chest." Tools and Trdes 40 (Winter
1993).
Roberts, Kenneth D. Scottish and English
Metal Planes by Spiers and Norris. Fitzwilliam,
N.H.: Ken Roberts Publishing, 1991.
-. Some 19th Centur English
Woodworking Tools. Fitzwilliam, N.H.: Ken
Roberts Publishing, 1 980.
-. The Stanley Rule and Level Company's
Combination Planes. Fitzwilliam, N.H. : Ken
Roberts Publishing, 1975.
-. Wooden Planes in 19th Centur America
Volume I Fitzwilliam, N.H.: Ken Roberts
Publishing, 1983.
Sellens, Alvin. Dictionar ofAmerican Hand
Tools. Augusta, Kans. : Alvin Sellens, 1990.
-. The Stanley Plane: A Histor and
Descriptive Inventory. Albany, N.Y. : Early
American Industries Association, 1 975.
-. Woodworking Planes: A Descriptive
Register of Wooden Planes. Augusta, Kans.:
Alvin Sellens, 1978.
Sainsbury, John. Planecraft: A Woodworker's
Handbook. New York: Sterling, 1984.
Salaman, R. A. Dictionar of Woodworking
Tools. Newtown, Conn. : Taunton Press, 1990.
The Sargent Tool Catalog CoLection.
Foreword by Paul Weidenschilling.
Mendham, N.J.: Astragal Press, 1993.
Seymour, John. The Forgotten Crfts. New
York: Portland House, 1984.
Sloane, Eric. A Museum ofEarlyAmerican
Tools. New York: Funk and Wagnalls, 1964.
Smith, Roger K. Patented Trnsitional and
Metallic Planes in America 1827-1927 Athol,
Mass.: Roger Smith, 1981.
-. Patented Transitional and Metallic
Planes in America, Volume I Athol, Mass. :
Roger Smith, 1992.
Stanley Rule and Level Co. How to Work with
Tools and Wood. New Britain, Conn.: Stanley
Rule and Level, 1927.
Starr, Richard. Woodworking with Kids.
Newtown, Conn.: Taunton Press, 1982.
The Tool Chest ofBenjamin Seaton. Swanley,
England: Tool and Trades Historical Society,
1994.
Welsh, Peter C. Woodworking Tools
1600-1900. United States National Museum
Bulletin 241. Washington, D.C.: Smithsonian
Institution, 1966.
Whelan, John M. Making Trditional
Wooden Planes. Mendham, N.J. : Astragal
Press, 1996.
-. The Wooden Plane: Its History, Form,
and Function. Mendham, N.J.: Astragal Press,
1993.
Wildung, Frank H. Woodworking Tools at
Shelburne Museum. Shelburne, Vt. :
Shelburne Museum, 1957.
T O O L CATA L O G S
A N D P R I C E L I S T S
Hammacher, Schlemmer & Co. Tools for all
Trdes, and Supplies. Catalog #355. New
York, c. 1905.
Illustrated Catalgue and Invoice Price List.
Greenfield, Mass.: Greenfield Tool Co.,
1872. Reprint, Fitzwilliam, N.H.: Ken
Roberts Publishing, 1978.
Illustrted List ofPlanes, Plane Irons,,,.
Sandusky, Ohio: Sandusky Tool Co., 1877.
Reprint, Fitzwilliam, N. H. : Ken Roberts
Publishing, 1978.
Illustrated Supplement to the Catalog and
Invoice Price List ofBench Planes, Molding
Tools, &. Middletown, Conn.: Arrow
mammett Works, 1857. Reprint, Fitzwilliam,
N.H.: Ken Roberts Publishing, 1976.
Major, Robert. Masterpiece Tools. Suncook,
N. H. : Mahogany Masterpieces, 1984.
Orr and Lockett Hardware Co. Chicago, Ill.,
1898.
Stanley Rule and Level Co. Various price and
pocket catalogs from 1870-1915. New
Britain, Conn.
Chas. A. Strelinger. Detroit, Mich., 1895.
Tool Catalogue 1938. Alex Mathieson and
Sons, Ltd., Saracen Tool Works.
A. J. Wilkinson & Co. Wood-Workers'
Catalogue. Boston, c. 1888.
B I B L l O G R A P H Y 259
A
Aluminum: for planes, modern, 37
Auburn Tool Company: wooden
plane manufacture of, 24
Auctions, tool: buying at, 245-48
B
Bailey, Leonard:
bench planes by, 52
chart of, 96
#5, pictured, 8
block plane (# 1 2'12) by, 160
early planes of, 23
frog style of, 47
adjusting, 58, 60, 61
metal planes of, begun, 7
planes of, vs. Stanley Bed Rocks,
47
rabbet plane (# I I ::)by, 1 25
smoothing planes by, 95
transitional planes by, 8
Victor planes by, 23, 38, 95, 249
Bailey Tool Company: soles by, with
letter corrugations, 43
Barrel planes: for lathe use, 209
Bayley: corebox plane by, 21 9-20
Beading planes: SeeMolding planes:
beading.
Benches:
board jacks for, 84
dog holes in, 79
dogs for, 80-81
heights for, 76-77
stops for, wedging, 81 -82
types of, 76
Seea/soHoldfasts. Vises.
Bench hooks: for squaring end grain,
1 1 6
Bench planes:
aluminum, 25
basic, 99
eastern, 94
history of, 7-8
iron geometry for, 46-49
metal, 7-8
Stanley-Bailey, 94-97
miniature, 235, 254-56
rabbet, 1 25, 1 26
Russian, 27
260
INDEX
Stanley-Bailey, chart of, 96
transitional, 8, 34-35
tuning, 99
types of, 93-99
using, 99-109
Seea/soJack planes. Jointer
planes. Scrub planes. sea:ute
arts Smoothing planes. Stock
preparation.
Benchstones:
ceramic, 65
diamond, 65
maintenance of, 70
oil-, 65
physical characteristics of, 64
water-, 64-65
Seea/soSharpening.
Birdsill:
smoothing plane by, 57
soles by, with drilled holes, 43
Blind nailers: described, 225-26
Block planes:
aluminum, 37
discussed, I I O-l l
experimental Stanley, 37, 7 9
iron angles for, 49
lever caps for, setting, 72
low-angle, contemporary, 239
rabbet, 1 1 8, 1 1 9
schoolboy, 36, 37
skewed, 1 1 8, 1 19, 236-37
for smoothing, 160
for smoothing curves, 1 66-67
tuning, 1 1 1 - 1 3
using, 1 1 3-1 9
wooden, with screw iron adjuster,
33
Board jacks: for long boards, 84
Boxing:
defined, 36
replacing, 194-95
British planes:
block, for smoothing, 160
bullnose rabbet, 52, 1 31
cast-iron, early, 1 8, 1 9
smoothing, 9-10, 52, 1 54-55,
1 59-60
Bronze: for plane bodies, 37, 42
Bullnose planes:
pictured, 9, 38
Seea/soRabbet planes: bullnose.
Burnishers: using, 178-80
Butcher blocks: plane for, I I O-l l
c
Capping planes: described, 216
Cast iron:
for plane bodies, 23-24, 37, 42
warped, reasons for, 54
Chairmaker's planes:
discussed, 21 5
shopmade, contemporary, 235
Chamfer planes: discussed, 199-202
Chamfers: types of, 1 99-200
Chapin-Stevens: wooden-plane
manufacture of, 24
Chaplin |O. RJ
blade adjuster of, 32, 33
block plane by, I I I
Chariot plane: shopmade,
contemporary, 241
Chatter: problem of, 91
Chelor, Cesar: panel-raising plane
by, 20
Chisel planes: discussed, 148-49
Cincinnati Tool Company:
spokeshave by, round, 206
Clifton: three-in-one shoulder
planes by, 146
Coachmaker's planes:
discussed, 216-1 8
shop made, contemporary, 235
Combination planes:
aluminum, 37
discussed, 9, I I, 185, 202-204
influence of, 1 88
Compass planes:
for curves, 1 66-67
discussed, 207-208
hollowing, 235
Cooper's planes: 21 2- 14
Corebox planes: described, 21 9-20
Cornices: making, 1 89-91
Crozes: described, 21 3, 214
D
Dado planes:
discussed, 1 32-34
iron profile for, 67
Davis Level Company: block plane
by, I I I
Dogs: SeeBenches.
Dovetail planes: discussed, 140
Downrights: described, 214
E
E. C. E.: wooden-plane manufacture
of, 24
End grain:
F
planes for, 48-49, 1 1 9
planing, 1 l0-1 l , I I 3
sash-coping plane for, 222
squaring, I I4-1 9
Fillister planes:
defined, 1 25
Seea/soRabbet planes.
Finger planes: SeeViolinmaker's
planes.
Fore planes: SeeJointer planes.
Frogs:
adjusting, 57-59, 60, 162
Bed Rock vs. Bailey, 47
importance of, 32
integral, 46, 57
two-piece, 46
G
Gage Tool Company: transitional
planes by, 35
Gladwin: wooden-plane iron
adjuster by, 33
Grain: reading, 87
Grooving planes: SeePlow planes.
Gunmetal:
defined, 37
for plane bodies, 42-43
plow plane of, 39
H
Hammacher Schlemmer:
violinmaker's planes by, 38
Handles:
materials for, 39
repairing, 52
shaping, 53
styles of, 37-39
tightening, 52-53
Handrail planes: described, 216
Holdfasts: L-shaped, 76, 77, 82-83
Hollow augers: discussed, 221 -22
Hollow planes: SeeMolding planes:
hollows and rounds.
Honing: SeeSharpening.
Howels: described, 21 3
Howkins: plow plane by, model C,
1 38
I
Ice planes: mentioned, II
Ingraham, Ted: makes planes,
230-34
Inshaves: described, 214
Iron: SeeCast iron. Steel.
Irons:
J
adjusters for, 32-34
angles for, 46-49
back bevels on, 49
backs of, flattening, 67-68
cap irons for,
early, 19, 20
importance of, 43
setting, 41, 71 -72
tuning, 71 -72, 162
cast steel, 1 8-1 9
cryogenic process for, 240
depth adjusters of, tuning, 72, 73
depth of, adjusting, 85-86
described, 30-31
eastern vs. western 44 1 59
lateral alignment o, 8-87
for low-angle planes, 1 1 2- 1 3
making, 234
metallurgy of, 45-46
microbevels on, 1 1 2-1 3
of molding planes, fit of, 1 95
pitch of, 46-48
for match planes, 1 35
for wood hardness, 41
replaceable, 1 56
shaping, 162-63
shimming, 1 61 -62
single vs. double, 32
skewed, 1 27
skewing, effectiveness of, 41
tapered vs. parallel, 44-45
thick, importance of, 44, 1 56-57,
1 59
variability in, 46
welded, 44-45
of wooden planes,
beds for, truing, 73
wedges for, tuning, 73
Seea/soSharpening.
Jack planes:
discussed, 99
iron profile for, 67
low-angle, 1 1 1, 1 17
uses for, 93
wooden, 6, 7
Seea/soBench planes.
Jamestown Tool Company:
production process of, 240-41
Joinery:
adjusting, planes for, 145-51
basic, diagrammed, 1 22
planes for, 9
value of planes in, 1 21
Seea/sosec|]|c}o|ats.
Jointer gauges: discussed, 108-109
Jointer planes:
barrel, long cast-iron, 21 2
European, carved French, 94
uses for, 93
wooden, 7
Seea/soBench planes.
Jointing:
for beveled edges, 108-109
for edge gluing, 105-108
process of, 102-108
with shooting board, 108
techniques for, 87-90
Seea/soMiters: edge.
K
Knowles, Hazard: cast-iron plane by,
23, 57
Krenov, James: on making planes,
229, 230
L
Lathes: barrel, planes with, 209
Lee, Joseph: chamfer plane by, 201
Lie-Nielsen Toolworks:
bench plane (# I ) by, 27
block plane by, 1 14
chisel planes by, 148, 149
planes by, 228-29
production process of, 236-39
smoothing plane by, 1 56, 236
Low-angle planes: SeeBlock planes.
Miter planes.
M
Marples:
block planes by, 160
smoothing plane by, 8
Mass: and plane performance, 42-43
Match planes: discussed, 1 34-37
Metal: SeeAluminum. Bronze. Cast
iron. Gunmetal. Steel.
Metallic Plane Company: block
plane by, 1 1 1
Miller:
match plane by, 13 5
plow plane by, Improved Joiner,
39, 1 39
Seea/soStanley.
Millers Falls:
block plane by, skew, 1 1 8
postwar production of, 26
smoothing planes by, 25, 26
spokeshave by, radiused, 206
Miter planes:
low-angle, British, 35, 168
shopmade, contemporary, 241
using, 142
Miters:
case, 142-43
clamps for, 142
edge, 144-45
frame, 141-42, 143
planes for, 142, 143, 144, 145
types of, 140-41
Molding planes:
and architectural changes, 21
basic combinations of, 1 88
beading, 1 91 -93
boxing of, replacing, 194-95
buying, 195-96
carpenter's chest of, 6
complex moldings with, 1 89-91
cornice, 1 89, 249
fluting, 191, 1 93
hollows and rounds, I I, 186-87
makers of, contemporary, 229-35
making, 231-34
manufacture of, 1 88
miniature, 187
reeding, 191, 192, 193
short-soled, for curves, 216, 217
spring with, 1 88, 189, 233
tuning, 194-95
using, 1 88-89, 194
wedges of, repairing, 1 95
whalebone, 1 87
wooden, early, 20
Seea/soIrons. Scratch stocks.
Mortise planes: described, 226
Mortises: planes for, 226
N
Nicholson, Francis: planes by, 20
Norris (Thomas) and Sons:
molding planes by, 4
panel plane by, 4
planes after, 239-41
smoothing planes by, 10, 52, 154,
I SS, 161, 167-69
o
Ohio Tool Company:
p
plow planes by, center-wheel, 1 38
scrub plane (#40) by, 97
wooden-plane manufacture of, 24
Panel-raising planes:
discussed, 198-99
shopmade, contemporary, 235
wooden, early, 20
Patternmaker
'
s planes: discussed,
218-20
Peg shapers: described, 38
Phillips: plow plane by, 1 36
Plane makers:
consolidation of, 24
contemporary, 229-41
early, stamps of, 20-21
mechanization and, 22
Planes:
basic, for shop, 250
cast-iron, anatomy of, 31-32
classes of, 6-1 1
cleaning, 252
collecting, 254-57
European, 17
evolution of, from adz, 14
fences for, 108-109
history of, 5-8, 1 3-27
infilled, with dense wood, 42
as investments, 252-53
Japanese, design differences in
44-45
'
and mass, 42-43
mechanics of, 29-30
metal, 7-8
old, buying, 244-54
razee, described, 90
repairing, 252
storing, 255
transitional, 8, 34-35
wooden, 5-7
anatomy of, 30-31
iron adjustment on, 33
iron soles for, 34
toe plates for, 34
woods for, 35-37, 42
Seea/soFrogs. Handles. Irons.
Soles. sec|]|cge.Throats.
I N D E X 261
Planing:
and grain direction, 87
long boards, 84-85
physics of, 39-41
problems with, 91
skewing during, 91
techniques for, 87-91
Seea/soBenches. Jointing. Stock
preparation. Surfacing.
Planing machine: Woods, c. 1830,
22
Plow planes:
center-wheel, 1 20, 1 38
coachmaker's T-, 217- 1 8
discussed, 1 37-39
gunmetal, 39
wooden, early, 20
Preston, Edward:
chamfer plane by, 201
rabbet plane by, 1 31
side, 1 51
reputation of, 25
side bead planes by, set of, 1 92
spokeshaves by, 205
Primus:
blade adjuster of, 32
smoothing plane by, 24
R
Rabbet planes:
aluminum, 37
bench-mouthed, 1 25, 125, 1 26
British, 1 24
bullnose, 9, 52, 1 24, 1 31
coachmaker's T-, 21 7
for curved edge, 1 25
discussed, 1 22-26
fillister, 125, 1 26, 1 28
Japanese, 1 28
iron profile for, 67
nickers on, 1 22-23, 1 24, 1 27
sash making, 223
side, 1 45, 1 50-51
skewed, 1 23, 1 28
tuning, 1 26-28
using, 1 28-30
Seealso Block planes: rabbet,
skewed. Shoulder planes.
Rabbets:
across grain, 130-31
cutting, 1 28-30
stopped, 1 31 -32
Razor plane: pictured, 25
Record:
block plane (#60Yz) by, 1 1 2
router plane (#271 ) by, 1 50
Reed Plane Company: production
process of, 239-41
Robbins, Leon: makes planes, 234
Rodier: soles by, wavy corrugated,
43
262 I N D E X
Round planes: SeeMolding planes:
hollows and rounds.
Rounder planes: discussed, 220-21
Router planes: discussed, 149-50
Rule joints: planes for, 226-27
Rumbold (c. M.) Company:
mortise plane by, 226
s
Sandusky Tool Company: plow
plane by, 1 38
Sargent & Company:
bench planes by, wooden, 7
blade adjuster of, 32, 33
block planes by, 1 1 3, 1 14, 1 1 8,
] ] 9, 160
four-edge plane by, aluminum, 25
match plane by, 136
postwar production of, 26
rabbet planes by, 9, lSI
scrub plane (# 162) by, 97
Sashmaker's planes: discussed,
222-23
Scraper planes:
buzz (cooper's), 210- 1 1 , 2 14
discussed, 10, 1 72, 173-74
eastern, 1 74
tuning, 1 81 -82
using, 1 82-83
Seea/soScrapers. Toothing planes.
Scrapers:
bevel-edged, sharpening, 1 80-81
cabinet, 172, 1 73
chair-devil, 173, 21 5
curved, sharpening, 1 81
for difficult wood, 163
discussed, 10, 1 71 -72
dynamics of, 174-75
hand-held, 1 72-73, 1 82
jointers for, 176-77
sharpening, 1 75-81
vs. smoothing planes, IS 3-54
spokeshave-type, 1 70-71 , 1 72-73
square-edged, burnishing, 178-81
toothing, 170-71
Seealso Scraper planes.
Scratch stocks:
with chamfer plane, 202
discussed, 196-97
Scrub planes:
discussed, 97-98
iron profile for, 67
using, 98-99
Sharpening:
approaches to, 62-63
back flattening in, 67-68
bevels for,
grinding, 63-66
hollow, 66
honing,
stones for, 68-69
technique for, 69-70
iron profiles in, 67
polishing in, strop for, 70-71
Seealso Benchstones.
Shaves:
cooper's, 21 4
hollowing, 21 5
Seealso Spokeshaves. Swifts.
Travishers.
Shoe-peg planes: discussed, 222
Shooting boards:
donkey's ear, 143-44
for edge jointing, 108
for end grain, 1 16
for miters, 141-42
Stanley, with plane (#52), 144
Shooting clamps: for miters, 142
Shoulder planes:
British, 146, 147
bullnose, 146
discussed, 146-47
Stanley series, 1 45, 147
tuning, 147
using, 147-1 48
Siegley: combination plane by, 9
Skewing: technique of, 41 , 91
Smoothing planes:
block planes as, 1 1 1 - 1 2, 160
British, 10, 52, 1 54-55, 1 56,
1 59-60, 167-69
contemporary, 237, 239
discussed, 9-10, 94-97, 154-57
eastern, 1 57, 1 58, 1 59
iron profile for, 67
vs. scrapers, 153-54
tuning, 160-63
using, 93, 163-67
wooden, 6, 7, 33, 1 57-59
Seea/soScrapers. Surfacing.
Soles:
cast-iron, truing, 54-56
edges of, chamfering, 57
flattening, 53
interchangeable, 21 8- 1 9
90 t o side, ensuring, 56
shaping, 233
smooth vs. corrugated, 43-44
waxing, 164
wooden,
repairing, 56
replacing, 57
truing, 56-57
Seea/soThroats.
Spelk planes: described, 225
Spiers:
miter plane by, 168
shoulder plane by, 146, 1 47
smoothing plane (#6) by, 1 0, 1 54
Spill planes: discussed, 224
Spoke pointers:
discussed, 221
Seealso Peg shapers.
Spokeshaves:
adjustable, 206
cast-iron, 205-207
chamfer, described, 200
curved, 204
pattern maker's, brass, 205
radiused, pictured, 206
scraper, for barrels, 210
using, 206-207
wooden, 204
Seealso Swifts. Travishers.
Stairmaker's planes: discussed, 216
Stanley:
beaders by, 196, 197
Bed Rock planes by, 46, 47
frog style of, 47, 58, 60, 61
bench planes by, 94-97
contemporary versions of,
237-39
blind nailer (#96) by, 225-26
block planes by,
aluminum, 37
experimental, 37, 79
#9, pictured, 1 10, ] ] 6
#9Yz, 1 1 2, ] ] 3, 1 14
#9 Y2A, modern, 27
#60Yz, pictured, 1 14
#64, ] ] 0
#95, 1 1 8, 1 1 9
#1 01 '/z, 38
skew (# 140), ] ] 8, 1 1 9
bullnose plane ( # 1 01 ) by, 38
carriage-maker's plane ( # 10) by
1 26, 1 28
catalogs from, 23, 248
chamfer plane (#72) by, 200-202
chamfer spokeshave (#65) by,
200
chisel and block plane (#RB5) by,
27
chisel plane (#97) by, 148, 149
combination planes by,
#45, aluminum, 37
#45, discussed, 203-204
#46, pictured, 9
#55, discussed, I I , 1 84-85,
203-204
compass planes by, 207-208
corebox plane (#57) by, 21 9
dado planes by, 1 32, 1 33
dovetail plane (#444) by, 140
early planes by, 23
"Handyman," with ready-edge
blade, 25, 26
jack planes by, low-angle, I l l ,
] ]7- 1 9
jointer gauge by, 108-109
match planes by, 1 35
planes of, modern, 27
plow plane by, Miller, 39, 1 39
postwar production of, 26
rabbet planes by,
aluminum (#78), 37
bench (#10 series), 1 25, 1 26,
1 28
bullnose (#90A), 9
curved (# 196), 1 25, 21 8
fillister (# 78), 1 26, 1 27, 1 28
fillister (#289), 1 26, 1 28
modern (#RBlO), 27
side, 150-51
router planes by, 149-50
scraper planes by, 174, 1 83
scrapers by, 1 72, 1 73, 1 82, 1 83
scrub plane (#340) by, 97, 99
shoot board and plane (#52) by,
144
shoulder planes (#90 series) by,
145, 147
smoothing planes by,
#1 , 94-95
# 1 -#4)2, ISS, 1 56, 1 59
#2, #3, 97, 1 66
#4, 95, 97, 1 61 , 163-64, 165
#604, #604)2, ISS, 163-64,
165, 166
soles by, corrugated, 43-44
spokeshaves by, 204, 206
sweetheart trademark of, 48
Seea|soBailey.
TOOL CREDITS
Stearns (E. CJ: hollow auger by, 221
Steel:
American, early, 1 9
cast, 18-19, 45-46
cryogenic process for, 240
development of, 14-1 5
English, early, 18, 1 9
hardness of, and bevels, 45
metallurgy and, 45-46
for plane bodies, 37, 42
Seea|soCast iron.
Steer: soles by, inlaid rosewood, 43
Stock preparation:
18th-century, 104
flattening in, 99-102
planes for, 7-8
process of, 93- 1 19
thicknessing in, 102
Seea|soJointing. Surfacing.
Stoup planes: described, 210- 1 1, 214
Super-surfacers: action of, 154
Surfacing:
of cross grain, 164, 1 65
of curves, 166-67
of glued-up panels, 107, 163
planes for, 1 53-69
vs. scrapers, 1 53-54
of tabletops, 163-65
Surform planes: mentioned, 25, 26
Swifts: described, 214
T
Table-leaf planes: discussed, 226-27
Tenons: cutting, 1 31
Throats:
adjustable, lJ 3
for rabbet planes, 1 23
setting, 61, 1 61
adjusters for, 34
adjustments to, 85
bench, 1 23
checking, 59
metal, adjusting, 59-60, 1 61
rabbet, 1 23, 1 24
width for, and shavings, 40-41
wooden,
adjusting, 56, 59-60, 161, 162
dovetailed keys for, 62, 94
repairing, 56, 61 -62
shimming, 61
Tongue and groove: planes for,
1 34-37
Toothing planes: discussed, 174, 1 81
Topping planes: described, 21 3
Tower and Lyon: Challenge jointer
plane by, 95
Transitional planes: described, 8,
34-35
Travishers:
described, 21 5
pictured, 204
Try planes: SeeJointer planes.
Tuning:
importance of, 51
Seea|soseam/eartssec|]|ces
o]|anes
Jonathan Binzen (p. 157; Krenov plane)
u
Union Tool Company:
blade adjuster of, 32, 33
mentioned, 25
smoothing plane (#0) by, 95
Universal planes: SeeCombination
planes.
v
Victor planes: SeeBailey, Leonard.
Violinmaker's planes:
discussed, 214-1 5
ha ndles for, 38
Vises:
bench dogs in, integral, 80
end, 79-80
side-vise stand-in for, 80
leg, 78
side, 78
double-screw, 74, 78
for long boards, 83-84
steel, commercial, 79
Seea|soShooting clamps.
w
Winding sticks:
making, 101
using, 100, 101
Windsor: beaders by, 197
Witchets: SeeRounder planes.
Worrall: wooden-plane iron adjuster
by, 33
Many people and museums were kind
enough to lend me tools to photograph.
M. S. Carter (pgs. 4, 10 bottom, 11 top, 17,
35 bottom, 42, 56 bottom, 62 bottom, 146,
186, 187, 193, 198 top, 204 bottom, 245 left,
254, 256)
Ron Raiselis, Strawbery Banke Museum,
Portsmouth, N.H. (pgs. 210, 212, 213,
214 top)
The tools in the Jollowing photogrphs (and,
where noted, the photographs themselves)
are courtesy of
Jonathan Cooper (p. 214 bottom)
Michael Dunbar (pgs. 24, 34 top, 90, 173,
189, 198 bottom, 215 top left, bottom right)
Ted Ingraham (pgs. 74, 83 top, 193, 216 left,
223, 224, 255 left)
Jamestown Tool Company (p. 241, planes
and photos)
Paul Kebabian (pgs. 6, 20, 33 top left, 43
top, 57, 81 bottom, 137, 168, 2m top, 222,
227, 242)
Shelburne Museum, Shelburne, Vt. (pgs. 2,
94 bottom, 123, 132 top, 134 bottom, 142,
148 top, 149, 170, 174 right, 215 top right,
216 right, 217 top, 218 top, 220 right)
Roger Smith (p. 209; illustration from
Patented Trnsitional and Metallic Planes in
America, Vol. L
Windsor Precision Museum, Windsor, Vt.
(p. 22)
Dean Zoerheide (pgs. 8 bottom, 9 right, 18,
19, 33 bottom right, 36, 50, 1 33 bottom,
136 bottom, 204 top, 208 left)
I N 0 E X 263
P U B L I S HE R : James P. Chiavell i
ACQU I S I T I ONS E DI T OR : Rick Peters
P U B L I S HI NG COOR D I NATOR : Joanne Renna
E DI TO R : Peter Chapman
L AYOUT A RTI S T: Carol Singer
I L LU S T RATOR : Kathleen Rushton
T Y P E FA C E : Berling
PA P E R : Warren Patina Matte, 70 lb., neutral pH
P R I N T E R : Quebecor Printing/Kingsport, Kingsport, Tennessee