• Terminal Blocks Explanation • 4 Blue LED Indicators Explanation TIMING CHART of MODES

DC+ DC 12V power supply + MO - the MODE OF THE TIMER. Set to between 1
DC 12V Programmable Input DC- DC 12V power supply - and 18 based on how you want the timer to work.
Mode 1-8 are self-starting upon power-on, while
Time Delay Relay Module CH1 3-30V high level voltage mode 9-18 require a high level pulse signal to MODE 4
trigger start-up and the high level need to be Off Delay &
Normally open, disconnected longer than 20ms.
SKU: U6030 NO when the timer off, short circuited On delay
T1 - FIRST TIME PERIOD DELAY. Based on the
mode selected, this is the delay from first receiv-
Output COM Common interface ing the input trigger pulse until the second action
happens. Look at the graphs in the next chapter
Normally closed, short circuited for further explanations.
NC with COM when the timer off, MODE 5
T2 - SECOND TIME PERIOD DELAY. Based on the Infinite Loop
mode selected, this is triggered by the completion
of the T1 delay. T2 determines the delay until the
of On Delay
• Press Buttons Explanation next action happens.
In Working Mode NX - NUMBER MULTIPLIER & DELAY CYCLE INDEX.
In the modes of 1 to 6 and 11 to 16, it’s used to
Default mode when powered on set the values of T1 and/or T2 to greater than
9999 seconds. The default value of NX is 0101. To MODE 6
Short press to enter power saving mode, determine the actual time delay, T1 is multiplied
This programmable multifunction time delay relay turn off the display, operate normally; Infinite Loop
module is designed for different kinds of control by the first two digits of NX. The resulting value is
SET the delay in seconds used by the timer. Similarly, of Off Delay
systems. It has 18 preset modes, users can program Long press to enter setting mode, the
one of the mode and its parameters to fit for their timer will stop operating and enter the the last two digits of NX are the multiplier for T2.
applications. The four keys are used for programming initial status. In the modes of finite loops (mode 7/8/17/18), NX
the relay module, the four segment LED display are is also the cycle index.
used for displaying the mode and timing information. SWI Long press to enter view mode.

SPECS • Press Buttons Explanation TIMING CHART of MODES TIMING CHART of MODES
Long press to set/cancel the function of
Working voltage DC 12V entering power saving mode automatically
Static current 5.5mA NUM+ if there is no any operation for 10s, the
display will flash twice if setting finished.
-30 -70 degrees (-20-60 Short Press SET to recover display briefly. MODE 1 MODE 7
Temperature limitation
degree recommended) On Delay Finite Loop
Long press to reset/recover the current of On Delay
DC 30V or AC 250V / DC NUM-
Load capacity mode and stop operating
28V or AC 125V
In View Mode
Load current 10A
SET Short press to switch the parameters
Max. frequency ≤5KHz
Long press to exit the view mode and MODE 2
Overall dimension 66*40*20mm SWI MODE 8
enter the working mode Off Delay
Finite Loop
Mounting hole pitch 59*33mm In Setting Mode of Off Delay
Short press to switch the setting parame-
ter, the corresponding LED will light;
WIRING & PART INSTRUCTION SET
Long press to save the parameters and
enter the working mode. MODE 3
Short press to switch the digits, the select- On Delay & MODE 9
ed digit will flash. Off Delay Self-locking
SWI Relay
Long press to set/cancel the decimal digits
when setting T1 or T2.
NUM+ Short press to increase the digit value.
NUM- Short press to decrease the digit value.
TIMING CHART of MODES TIMING CHART of MODES

MODE 10 MODE 16
Triggered On, Triggered
and Off Delay Infinite Loop
after the CH1 of Off Delay
signal disap- and On Delay
pearing

MODE 17
Triggered
MODE 11 finite Loop of
Triggered On On Delay and
Delay Off Delay

MODE 18
Triggered
MODE 12 finite Loop of
Triggered Off Off Delay and
Delay On Delay

TIMING CHART of MODES QUICK START GUIDE

Setting example: Delay on a light after 5s.
Step 1. Select the right working mode: Mode 1
MODE 13
Triggered On Step 2. Long press SET to enter Setting mode; (at
delay & Off this moment the segment LED display starts to
delay flash at the far right)
Step 3. Short press SET to select parameters of
MD; (at this moment the LED near MD turn on
constantly)
Step 4. Short press NUM+/NUM-, enter 0005, the
MODE 14 value of segment LED display, that means 5s.
Triggered Off Short press SWI to move cursor among 4 segment
Delay & On LED displays;
Delay Step 5. Long press SET to exit the Setting mode
and enter working mode.

MODE 15
Triggered CONTACT US
Infinite Loop
of On Delay If any problem, please feel free to contact us.
and Off Delay
Website: www.uctronics.com
Email: [email protected]