SRM-80A / E – SIGNAL ROUTER/MONITOR

Owner’s Manual

SRM-80A
SIGNAL ROUTER / MONITOR

ROUTER /
MONITOR SERIES

Downloaded from www.Manualslib.com manuals search engine

 SRM-80A / E – SIGNAL ROUTER/MONITOR

INTRODUCTION ABOUT THE SRM-80

The SRM-80A facilitates mixdown and dub-
Congratulations on your purchase bing between different media types without
tying up additional console channels. By con-
of a Furman Model SRM-80A Signal necting the control room outputs of your mixer,
Router/Monitor. Your SRM-80A will inputs and of up to three power amplifiers or
powered speakers, speaker outputs of one
make monitoring, mixdown, and dub- stereo power amplifier, and up to three pairs
of speakers, you will have a highly useful and
bing simpler and faster, thus helping sophisticated audio playback monitor system.
Multiple copies can be made simultaneously
you achieve professional results. through use of the SRM-80A’s four rotary

MO N ITOR LIN E OUTPU T A SPEAKER C OUTPU T

SYSTEM PO W ERE D SPEAKERS SPEAKER B OUTPU T PA SSIVE SPEAKERS
PA SSIVE SPEAKERS
SETUP 1

PO W ER AM PLIFIER
IN PU T OU TPU T

H EAD PH O N ES

MO N ITOR LIN E OUTPU T B

FROM SET SW ITC H
MO N ITOR LIN E OUTPU T A TO SPK-B/C
AM P(B)
TO “A” N
I OU TPU T
FROM “A” OUT
FROM “C ” OUT
OU TPU T IN PU T SRM -80A
TO “C ” N
I
OU TPU T IN PU T
TO SOURCE IN
D AT RECOR D ER
TO “B” N
I MIN ID ISC
FROM “B” OUT FROM “D ” OUT
OU TPU T IN PU T
TO “D ” N
I
OU TPU T IN PU T

C ASSE TTE RECOR D ER

SRM -RU
COM PA C T D ISC PLAYER
SOURCE MIXER -RECOR D ER -

Downloaded from www.Manualslib.com manuals search engine

 SRM-80A / E – SIGNAL ROUTER/MONITOR

STEP-BY-STEP GUIDE TO SET-UP USING SINGLE POWER AMP

● Please also refer to the “System Set-Up #1” drawing on the facing page.
● Cables needed:
2 Pair: Speaker to Binding Posts, the banana plug type (Speakers B, C)
1 Pair: 1/4” TRS Balanced to Monitor Line output “A” (Powered Speakers)
6 Pair: RCA I/O to Devices
2 Pair: 1/4” TRS Balanced to Device “A” L/R I/O
1 Pair: 1/4” TRS Balanced to “SOURCE” L/R Input
1 Pair: 1/4” TRS Balanced to Power Amp L/R Inputs
1 Pair: Power Amp Out to “FROM POWER AMP OUT” Binding Posts (banana plugs)
● Make sure SRM-80 and all other devices are switched “OFF” before making any cable connections.
● Decide which devices will be labeled “A”, “B”, “C”, and “D”. Device “A” should be any pro level balanced units,
such as a DAT machine. Label the Output Select Switch and the speaker pairs on the front panel tabs. Use
adhesive labels so you can relabel for different configurations.
● Mount the SRM-80 in your rack. Depending on your setup, it may be easier to cable all your gear before mount-
ing the SRM-80 in your rack. Otherwise, go ahead and mount it now.
● Set AMP/SPK - B/C Switch to SPK - B/C.
● Connect passive speaker cables to “SPEAKER C” and “SPEAKER B” Binding Posts.
● Connect Power Amp L/R Output cables to “FROM AMP OUTPUT” Binding Posts.
● If you have the optional SRM-RU remote unit, which we highly recommend, connect its 5-Pin
cable to “REMOTE.”
● Connect 1/4” TRS Balanced cables from your powered monitors to MONITOR LINE OUTPUT “A” L/R.
● Connect 1/4” TRS Balanced cables from MONITOR LINE OUTPUT “B” L/R to your power amp “IN” L/R.
● Connect RCA cables from “L/R In/Out” to devices “B”, “C”, and “D”, according to your setup plan.
● Connect 1/4” TRS Balanced cables from “A” L/R, I/O to device “A”
● Connect 1/4” TRS Balanced cables from “SOURCE” L/R to source device.
(e.g. mixing console stereo out or soundcard out).
● Set the Ground Lift Switch to the position that reduces any hum or buzz.
● Set the “0db / +4db” switch to the appropriate meter scale for the equipment being used.
● Power up your equipment, being sure to turn on your power amp last.
● Set “SPEAKER TRIM” controls at about 75%. After powering up the system, adjust levels as needed. To dial in
your speaker levels use broadband pink noise and sound level meter. The Alan Parsons/Stephen Court align-
ment CD is very good, and a decent meter can be had for about $40 at Radio Shack.
For using more than 1 pair of power speakers or multiple power amps see System Set-up #2 on the next page.

Downloaded from www.Manualslib.com manuals search engine

 SRM-80A / E – SIGNAL ROUTER/MONITOR

source select knobs labeled OUTPUT SE- B/C AMP/SPK Switch. Each monitor speaker
LECT A through OUTPUT SELECT D. output has its own front panel trim control, so
equal listening levels can be maintained de-
Monitoring any of these sources can be done spite differences in speaker efficiencies.
using the MONITOR SELECT knob, high-
power headphone amp and uniquely thought- The SRM-80A has balanced inputs for the
out speaker selection system that consists of SOURCE and A inputs, and balanced outputs
three balanced line level speaker outputs A, for channel A output and A, B, and C moni-
B, and C. All of these outputs are compatible tor line outputs. INPUTS B through D utilize
with powered monitors or passive speakers unbalanced RCA jacks. The SRM-80A allows
using a power amp. The unique feature is that easy signal routing between these dissimilar
the B and C outputs can be combined into one jacks.
output for use with 2 pairs of passive speakers
and only one power amp. See description of

MO N ITOR LIN E OUTPU T A

SYSTEM PO W ERE D SPEAKERS
MO N ITOR LIN E OUTPU T B PASSIVE SPEAKERS
SETUP 2 PO W ERE D SPEAKERS

PO W ER AM PLIFIER
MO N ITOR LIN E
OU TPU T B INP U T OU TPU T
MO N ITOR LIN E OUTPU T A

MO N ITOR LIN E H EAD PH O N ES

OU TPU T C
SET SW ITC H
TO AM P-B/C
TO “A” N
I
FROM “A” OUT FROM “C ” OUT
OU TPU T INP U T SRM -80A
TO “C ” N
I
OU TPU T INP U T
TO SOURCE IN
D AT RECOR D ER
TO "B" N
I MIN ID ISC
FROM “B” OUT FROM “D ” OUT
OU TPU T INP U T
TO “D ” N
I
OU TPU T INP U T

C ASSE TTE RECOR D ER SRM -RU

SOURCE MIXER COM PAC T D ISC PLAYER
-RECOR D ER -
3

Downloaded from www.Manualslib.com manuals search engine

 SRM-80A / E – SIGNAL ROUTER/MONITOR

The SRM-80A provides a high-resolution 40 messed up the stereo image! (Only the sends
LED x 2 bar graph meter to display the signal to the speakers are affected.) While radio air-
selected for listening. The meter displays a play is nearly always stereo these days, phas-
pre-fader signal for accurate monitoring of ing problems and odd panning arrangements
the signal going to tape or disc. This meter can show up in less than ideal listening envi-
has true VU ballistics, or can be switched to ronments, such as cars, and many locations in
Peak Program Mode via the front panel toggle nightclubs.
switch. The meter also features a slow re-
lease-time Peak Hold function to allow easy The SRM-80A also features a DIM switch to
verification of critical levels. allow an easy way to lower the level to the
speakers (but not the headphones) tempo-
The SRM-80A’s MONO SUM feature provides rarily without disturbing any level controls.
the ability to check for radio compatibility,
and is a good spot check to see how you’ve

Input to Output Routing Switches

Balanced Buffers Connect any Input to any Output --EXCEPT-- A cannot send to A, B cannot send to B etc.
S Outputs
Source B A
1/4" TRS C 1/4" TRS
D Floating Bal. output Stage, 0dB gain
Input A Routing
Select B
1/4" TRS RCA
4 position
(4 switches)
Unbalanced Buffers C
Input B Monitor RCA
RCA Select
5 position
S
D
Input C RCA
A
RCA
B Headphone Volume Headphone
C and Amplifier (Front Panel,
Input D
RCA D +6dB gain 1/4" TRS)
+6 dB gain Amplifier Select Relays
Amp A
VU / PPM +6dB gain Speaker 1/4" TRS
0 VU = 0dBu
Meter Volume Control Amplifier VCA
0 VU = +4dBu and Mono Sum and floating
balanced
Mono Control output stage
Gain Control for Amp
Push button switches A vs B vs C and DIM
Amp B
Remote Control (Amplifier Select, Mono, Dim) Select Amp A vs Amp B/C 1/4" TRS
5 Pin DIN
Select Amp / Spkr B/C
Amplifier Level Trim Pots Amp C
1/4" TRS
Amp B/C Low level Relay
or
Speaker B/C Amp B Output
5 way post

To Speaker B
5 way post
To Speaker C
High level Relay 5 way post

Downloaded from www.Manualslib.com manuals search engine

 SRM-80A / E – SIGNAL ROUTER/MONITOR

OPTIONAL SRM-RU ring the panel when tightening the screws, use
nylon washers under the screw heads.
REMOTE CONTROL
The optional five-button SRM-RU allows re-
mote control of Speaker Selection, MONO and SAFETY INFORMATION
DIM. An LED indicator is provided for each WARNING (For domestic units only): Do not
button and a 10 foot cable is included. remove the third prong on the SRM-80A’s AC
plug. Never use a 3-prong to 2-prong AC plug
adapter to plug your SRM-80A into your wall
ABOUT THIS MANUAL socket. The unit requires that a safety ground
We want to make it easy for you to set up your be present for proper operation. Any attempt to
SRM-80A. Page Two of this manual tells you operate it without a safety ground is considered
how to do just that, step-by-step. Page four improper operation and could invalidate the
gives you detailed information on all of the warranty.
features, controls and connectors. You can
set up your SRM-80A first, and read about the
controls afterwards or even better, just resume FRONT PANEL CONTROLS
recording and mixing! OUTPUT SELECT A: Use this input/output for
balanced, pro level devices. This four-position
knob determines which signal is routed to the
INSTALLATION device plugged into the 1/4” “A” OUTPUTS on
The SRM-80A is intended for mounting in the SRM-80A’s rear panel. For example, if the
standard 19" equipment racks. To avoid mar- “A” OUTPUTS are used for a DAT machine, the

SW ITC H SETTIN
ING S FO R M U LTI
IC A SSE TTE D U BBING
C ASSE TTE C ASSE TTE C D PLAYER
REC O RD ER REC O RD ER D
INPUT -D INPUT -D INPUT -D INPUT -C C
INPUT -C INPUT -C INPUT - B INPUT - B B
INPUT - B INPUT -A INPUT -A INPUT -A A
SOU RCE
OUTPUT
SELEC T A OUTPUT
SELEC T B OUTPUT
SELEC T C OUTPUT
SELEC T D M O NITO R
SELEC T

SET OUTPUT SELEC T SW ITC H ES SET M O NITO R SELEC T SW ITC H

B AN D C TO INPUT -D .TH IS W ILL TO D TO LISTEN TO WH AT S I
ROUT TH E C D PLAYER TO BOT H BEIN
ING REC O RD ED TH ROU GH TH E
C ASSE TTE D EC KS C O NN EC TED TO SPEAKERS AN D H EAD PH O N ES
TH E B AN D C OUTPUT S

Downloaded from www.Manualslib.com manuals search engine

 SRM-80A / E – SIGNAL ROUTER/MONITOR

DAT can receive signals from device “Source”, stereo to monaural.

“B”, “C”, or “D” INPUTS depending on where
you position this knob. DIM: Attenuates the loudness of your speakers
by about 15 dB, without affecting the level of
OUTPUT SELECT B: This four-position knob the signals going to any of the stereo devices or
works like the output select “A” knob described headphones connected to the SRM-80A. This
above. For example, if the “B” RCA OUTPUTS is a very useful feature if you are interrupted
on the back panel are used for a cassette while monitoring, mixing, or dubbing.
recorder, the recorder can receive signals from
stereo device Source, “A”, “C”, or “D” INPUTS. MONITOR LEVEL: This high-resolution, 40 x 2
LED bar graph meter allows precise pre-fade
OUTPUT SELECT C: The SRM-80A’s “C” level calibration for all stereo devices con-
OUTPUTS can receive signals from device nected to the SRM-80A.
“Source”, “A”, “B”, or “D” INPUTS depending
on where you position this knob. For example, METER MODE: Located to the right of Mon-
if the “C” RCA OUTPUTS on the back panel itor Level Meter, this switch can be set for the
are used for a MiniDisc recorder, the re- meter to display AVG (VU) or Peak Mode.
corder can receive signals from stereo device SPEAKERS A, B, and C: Selects between
“Source”, “A”, “B”, or “D” INPUTS. amplifier / speaker outputs A, B, or C.
OUTPUT SELECT D: The SRM-80A’s “D” TRIM LEVELS: Adjusting these “Set Once”
OUTPUTS can receive signals from device controls allows you to set all three pairs of am-
“Source” “A”, “B”, or “C” INPUTS. For ex- plifiers/speakers to the same listening level.
ample, if the “D” RCA OUTPUTS on the back
panel are used for a CD player/recorder, the HEADPHONES: Plug your headphones in
recorder can receive signals from stereo de- here. The high-power headphone amp pro-
vice “Source”, “A”, “B”, or “C” INPUTS. vides excellent audio quality and can drive
low-impedance phones with ease. It may be
MONITOR SELECT: This five-position knob wise to disconnect your headphones to avoid
allows you to select which device you will hear damage when not in use.
through your speakers and headphones, the
main console or soundcard mix (Source), or HEADPHONE LEVEL: Adjusts the listening
the output of any devices “A” through “D”. level of the headphones.

LISTENING LEVEL: Controls the loudness

level you hear through your speakers. It does REAR PANEL CONTROLS AND
not affect the signal going to any of the stereo CONNECTIONS
devices connected to the SRM-80A. GROUND LIFT: Allows separation of chassis
ground from audio ground and can be used
MONO: Changes the sound you hear through
to reduce hum or buzz. Remember, never
your speakers (not in the Headphones) from
remove the third prong on the SRM-80A’s AC
6

Downloaded from www.Manualslib.com manuals search engine

 SRM-80A / E – SIGNAL ROUTER/MONITOR

plug. Never use a three-prong to two-prong B/C position: Only the “A” and “B” monitor
AC plug adapter to plug your SRM-80A into line outputs are used and the “B” amplifier’s
your wall socket. speaker outputs are connected to the “FROM
AMP (B) OUTPUT” binding posts. The B
ON/OFF: Controls power to unit. and C speaker outputs are combined to the
AMP-B/C & SPK-B/C SWITCH: When the B/C SPEAKER B output jacks. This is to be used
switch is in the AMP-B/C position: The input with a single power amp and 2 pairs of pas-
selected by the Monitor Select switch is routed sive speakers via the binding posts on rear
through the Monitor level control and sent to panel. Connect the SPEAKER B/POWER
the “A”, “B” or “C” monitor line outputs (as AMP IN jacks to the input of your power amp.
selected with the “A”, “B” or “C” pushbuttons). Connect the output of your power amp to the
B and C speaker outputs and output signals FROM AMP OUTPUT Binding posts. Connect
are separate for use as individual outputs with 1 pair of passive speakers to the SPEAKER
either powered speakers or passive speakers B binding posts and the other pair of passive
with a power amp. See Figure A. speakers to the SPEAKER C binding posts. To
select the associated amplifier / speaker press
When the AMP/SPK B/C switch is in the SPK- the “A”, “B,” or “C” speaker select buttons on
the front panel. See Figure B.

FIGURE A
C O NN EC TI
IO N S FO R 3 API
P IR S O F PO W ER ED
SPEA K ER S O R PA SS IV E SPEA K ER S WITH
AMP-B/C SPK-
B/C SWITCH IS
SEPA R A TE PO W ER A MP S
SET TO AMP-B/C
AMP-B/C SPEAKER C SPEAKER B
120 VAC INPUT 60 HZ MADE IN CHINA FROM AMP(B)

GROUND
ON OUTPUT REMOTE
USE MODEL
SRM-RU
L L
AMP-B/C ONLY
LIFT

L L L C B A CONNECT LINE OUTPUTS

5 WATTS R R R
SPK-B/C R R
A, B AND C TO THE INPU
SPK-B/C OFF
OF POWERED SPEAKERS
AVIS:N'OUVREZ PAS-RISQUE DE CHOC ELECTRIQUE CAUTION: TO PREVENT ELECTRIC SHOCK DO NOT REMOVE COVER. REFER SERVICING TO QUALIFIED PERSON
CONNECT TO POWERED MONITORS
OR POWER AMPLIFIERS INPUTS
OR POWER AMPLIFIERS.

SPEAKER C SPEAKER B INPUT FROM

OUTPUT IS OUTPUT IS AMP IS NOT
NOT USED NOT USED USED

FIGURE B
C O NN EC TI
IO N S FO R 2 API
P IR S O F PA SS IV E BOTH LINE OUTPUTS
AMP-B/C SPK-
B/C SWITCH IS
SPEA K ER WITH A SINGIN LE PO W ER A MP
ING B AND C WILL BE
PRESENT AT THE B
1/4" OUTPUTS.
SET TO SPK-B/C
AMP-B/C 120 VAC INPUT 60 HZ
ON
MADE IN CHINA SPEAKER C SPEAKER B FROM AMP(B)
OUTPUT REMOTE
GROUND USE MODEL
SRM-RU
L L
AMP-B/C ONLY
LIFT

L L L C B A
5 WATTS R R R CONNECT LINE OUTPUT
SPK-B/C R R A TO THE INPUTS OF
SPK-B/C OFF POWERED SPEAKERS
OR POWER AMPLIFIER.
CONNECT TO POWERED MONITORS
AVIS:N'OUVREZ PAS-RISQUE DE CHOC ELECTRIQUE CAUTION: TO PREVENT ELECTRIC SHOCK DO NOT REMOVE COVER. REFER SERVICING TO QUALIFIED PERSON OR POWER AMPLIFIERS INPUTS

NO SIGNAL WILL
CONNECT CONNECT CONNECT BE PRESENT AT
PASSIVE PASSIVE OUTPUT OF THE 1/4" LINE
SPEAKERS TO SPEAKERS TO AMPLIFIER TO OUTPUT C
SPEAKER C SPEAKER B THESE INPUTS
OUTPUTS OUTPUTS

Downloaded from www.Manualslib.com manuals search engine

 SRM-80A / E – SIGNAL ROUTER/MONITOR

SPEAKERS B AND C Binding posts: For use MONITOR LINE OUTPUTS TO SPEAKER “B”
with a single power amp. These left-right bind- /POWER AMP IN: When the AMP/SPK-B/C
ing posts are provided for speaker pairs “B” switch is in the AMP-B/C position use these
and “C”. You may connect only passive speak- Left and Right 1/4” phone jacks to connect
ers here. See figure B. a pair of powered speakers or a power amp
/ passive speakers. See figure A. When the
NOTE: If you’d like to use a pair of powered AMP/SPK-B/C switch is set to SPK-B/C both
speakers with your SRM-80A, do not connect B and C output signals will be present at these
them to the “B” or “C” binding posts. Set the jacks. The SRM-80A uses these jacks to send
AMP/SPK-B/C switch to the AMP- B/C position. either B or C output signals to your power
Now you may use “A”, “B”, or “C” amplifier / amp, and the power amp’s speaker output is
speaker line outputs for powered speakers. returned to the SRM-80A via the FROM AMP
FROM AMP OUTPUT: These Left-Right bind- OUTPUT binding posts mentioned above.
ing posts are provided to connect the Left From there, the SRM-80A sends the amplified
and Right speaker cables from the output of signal to the passive speakers connected to
your power amplifier when the AMP/SPK- the SRM-80A’s “B” and “C” speaker binding
B/C switch is set to SPK-B/C. The SRM-80A posts. See figure B.
routes these amplified output signals to either MONITOR LINE OUTPUTS TO SPEAKER “A”
Speaker pair “B” or “C”, depending on which /POWER AMP IN: Use these Left and Right
Speaker select button you press on the front 1/4” phone jacks to connect a pair of powered
panel or the SRM-RU remote unit. Be careful to speakers or a power amp / passive speakers.
connect the output of your power amp to these
binding posts only. The relay that does the INPUTS/OUTPUTS “B,” “C,” AND “D”: RCA
switching is rated at 8A/240 volts. See figure B. jacks for the inputs and outputs of an unbal-
anced device such as a cassette, CD player/
REMOTE: Accepts the cable for the optional recorder or MiniDisk.
SRM-RU remote control unit. You will need to
use a 5 pin din type cable a midi cable will not INPUTS/OUTPUTS “A”: Left-Right 1/4” TRS
work properly. jacks for the inputs and outputs of a balanced,
pro level device.
MONITOR LINE OUTPUTS TO SPEAKER “C”
/POWER AMP IN: Use these Left and Right SOURCE INPUTS: These 1/4” TRS jacks are
1/4” phone jacks to connect a pair of powered provided to connect your studio’s main mixer,
speakers or passive speakers with a power soundcard or multi-track recorder output to the
amp when the AMP/SPK-B/C switch is in the SRM-80A.
AMP-B/C position. If the switch is set to SPK-
B/C there will be no signal present. See figure LEVEL SELECT SWITCH: Selects +4dBu or
B. 0dBu = 0 indication.

Downloaded from www.Manualslib.com manuals search engine

 SRM-80A / E – SIGNAL ROUTER/MONITOR

THREE YEAR OTHER WARRANTIES, EXPRESS OR IM-

PLIED, INCLUDING BUT NOT LIMITED
LIMITED WARRANTY TO THE IMPLIED WARRANTIES OF MER-
Furman Sound, Inc., having its principal place CHANTABILITY AND FITNESS FOR A PAR-
of business at 1997 South McDowell Blvd., TICULAR PURPOSE. Manufacturer does not
Petaluma, CA 94954 (“Manufacturer”) war- warrant against damages or defects arising
rants its SRM-80A (the “Product”) as follows: out of improper or abnormal use of handling of
Manufacturer warrants to the original Pur- the Product; against defects or damages aris-
chaser of the Product that the Product sold ing from improper installation, against defects
hereunder will be free from defects in material in products or components not manufactured
and workmanship for a period of three years by Manufacturer, or against damages resulting
from the date of purchase. The Purchaser of from such non-Manufacturer made products
the product is allowed fifteen days from the or components. This warranty shall be can-
date of purchase to complete warranty regis- celable by Manufacturer at its sole discretion
tration by mail or on-line at the Furman web- if the product is modified in any way without
site. If the Product does not conform to this written authorization from Furman Sound. This
Limited Warranty during the warranty period warranty also does not apply to Products upon
(as herein above specified), Purchaser shall which repairs have been affected or attempted
notify Manufacturer in writing of the claimed by persons other than pursuant to written
defects. If the defects are of such type and authorization by Manufacturer.
nature as to be covered by this warranty, THIS WARRANTY IS EXCLUSIVE. The
Manufacturer shall authorize Purchaser to re- sole and exclusive obligation of Manufacturer
turn the Product to the Furman factory or to an shall be to repair or replace the defective
authorized Furman repair location. Warranty Product in the manner and for the period pro-
claims should be accompanied by a copy of vided above. Manufacturer shall not have any
the original purchase invoice showing the pur- other obligation with respect to the Products or
chase date; this is not necessary if the War- any part thereof, whether based on contract,
ranty Registration was completed either via tort, strict liability or otherwise. Under no cir-
the mailed in warranty card or on-line website cumstances, whether based on this Limited
registration. Shipping charges to the Furman Warranty or otherwise, shall Manufacturer be
factory or to an authorized repair location must liable for incidental, special, or consequen-
be prepaid by the Purchaser of the product. tial damages. Manufacturer’s employees or
Manufacturer shall, at its own expense, furnish representatives’ ORAL OR OTHER WRIT-
a replacement Product or, at Manufacturer’s TEN STATEMENTS DO NOT CONSTITUTE
option, repair the defective Product. Return WARRANTIES, shall not be relied upon by
shipping charges back to Purchaser will be Purchaser, and are not a part of the contract
paid by Manufacturer. for sale or this limited warranty. This Limited
THE FOREGOING IS IN LIEU OF ALL Warranty states the entire obligation of Manu-

Downloaded from www.Manualslib.com manuals search engine

 SRM-80A / E – SIGNAL ROUTER/MONITOR

facturer with respect to the Product. If any part

of this Limited Warranty is determined to be
void or illegal, the remainder shall remain in
full force and effect.

SERVICE
Before returning any equipment for repair,
please be sure that it is adequately packed
and cushioned against damage in shipment,
and that it is insured. We suggest that you
save the original packaging and use it to ship
the product for servicing. Please enclose a
note giving your name, address, phone num-
ber and a description of the problem. NOTE:
All equipment being returned for repair must
have a Return Authorization (R/A) Number. To
get an R/A Number, please call the Furman
Service Department, (707) 763-1010 ext. 120
or 121, between 8 a.m. and 5 p.m., U.S. Pa-
cific Time. Please display your R/A Number on
the front of all packages.

10

Downloaded from www.Manualslib.com manuals search engine

 SRM-80A / E – SIGNAL ROUTER/MONITOR

SRM-80A SPECIFICATIONS
OPERATING VOLTAGE Output Impedance: 56 ohms
90 to 140 VAC ("E" version 180 to 280 VAC)
THD + N: 0.001% with 750mW driv-
LINE IN/OUT ing a 150 ohm load.
Input Impedances:
Source 24 Kohms POWER AMP
A Input 24 Kohms Output Impedance: 50 ohms
B Input 40 Kohms
Connectors: 1/4” TRS balanced
C Input 40 Kohms
D Input 40 Kohms SPEAKER OUTPUT SWITCHING 8A/240V
Connectors: Power amp and speaker
Output Impedances:
connectors: 5-way binding
A Output 50 ohms
posts
To Power Amp 50 ohms
B,C,D Output: <50 ohms
METERS
Accuracy: ±0.5 dB
Sensitivity for 0 VU: 0 dBu (.775 Vrms)
or +4 dBu (1.23 Vrms) MECHANICAL
Dimensions: 1.75” H x 19” W x 6.625”
Max. Through Input Level: +21 dBu (8.7 Vrms) D. Weight: 6 lbs (2.7 kg)
NOTES
Max. Output Level: +27dBu (17.34Vrms) 0 dBu equals .775 Vrms
MONITOR OUTPUTS
Noise: <-95dBu, 20Hz to 20kHz.

THD + N: 0.003% maximum

Crosstalk: -83dB minimum @ 10kHz

Connectors: Balanced TRS input and

output jacks sends. RCA
jacks for “B”, “C”, and “D”
inputs and outputs.

HEADPHONE OUTPUT
Specifications subject to change without notice

Furman Sound, Inc.

1997 South McDowell Blvd.
Petaluma, California 94954-6919 USA
Phone: 707-763-1010
Fax: 707-763-1310
Web: www.furmansound.com
0003-082703-B
E-mail: [email protected]

Downloaded from www.Manualslib.com manuals search engine