Scribd
Upload
43 views

Key programming

This document provides key programming instructions for the Rover 45 (1999-2006), including the need for a repair code found on the security card. It details the steps to program keys and synchronize the remote control, emphasizing caution during the process. Additionally, it includes instructions for replacing the button cell in the remote control.

Uploaded by

Nicoleta
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
43 views

Key programming

This document provides key programming instructions for the Rover 45 (1999-2006), including the need for a repair code found on the security card. It details the steps to program keys and synchronize the remote control, emphasizing caution during the process. Additionally, it includes instructions for replacing the button cell in the remote control.

Uploaded by

Nicoleta
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Page 1/2

ROVER 45 (RT)2.0 iDT 100 20T2N


1999 - 2006

Key programming
General
Before programming the key(s) a repair code is required
The repair code is recorded on the security card
Note: Never leave the security card in the vehicle

Programming keys
Procedure in case the remote control is lost or fails to operate

Turn the ignition off


Close the driver's door
Insert the key into the driver's door lock
Turn the key to the UNLOCK position the number of times indicated by the first digit of the code
Turn the key to the LOCK position the number of times indicated by the second digit of the code
Turn the key to the UNLOCK position the number of times indicated by the third digit of the code
Turn the key to the LOCK position the number of times indicated by the fourth digit of the code
Note: Ensure the key is fully returned to the centre position after each turn
The security indicator light will stop flashing
This indicates that the password has been correctly entered
Wait for 5 minutes
Within (X) minutes (X = 10)
The engine can be started

Programming remote control


Synchronize the transmission signal of the remote control
Use the key to unlock the door
Press the lock button (X) times (X = 5)
The remote controls are synchronized

Button cell
©HaynesPro B.V.renewal Powered by Haynes Pro 2015
Use a coin to remove the button cell cover
Insert a coin at the ring
Caution! Avoid damaging the seal between the two halves of the case
Remove the button cell
Page 2/2

ROVER 45 (RT)2.0 iDT 100 20T2N


1999 - 2006

Key programming
General
Caution! Do not touch the printed circuits
Beforeand
Press programming
hold each button
the key(s)
in turn
a repair
for at code
least is(X)
required
seconds
The repair
This will drain
codeany
is residual
recordedpower
on thefrom
security
the remote
card control
Note: Never
Install a newleave
button
the
cell
security
with the
card
positive
in theside
vehicle
facing upwards
Refit the cover keys
Programming
Procedure in case the remote control is lost or fails toB.V.
©HaynesPro operate

Turn the ignition off


Close the driver's door
Insert the key into the driver's door lock
Turn the key to the UNLOCK position the number of times indicated by the first digit of the code
Turn the key to the LOCK position the number of times indicated by the second digit of the code
Turn the key to the UNLOCK position the number of times indicated by the third digit of the code
Turn the key to the LOCK position the number of times indicated by the fourth digit of the code
Note: Ensure the key is fully returned to the centre position after each turn
The security indicator light will stop flashing
This indicates that the password has been correctly entered
Wait for 5 minutes
Within (X) minutes (X = 10)
The engine can be started

Programming remote control


Synchronize the transmission signal of the remote control
Use the key to unlock the door
Press the lock button (X) times (X = 5)
The remote controls are synchronized

Button cell
©HaynesPro B.V.renewal Powered by Haynes Pro 2015

You might also like