Fingerprint Control

User Manual

Please read the instructions carefully before use

1. Introduction
It supports fingerprints and EM RFID card. The performance has been
greatly improved.
The product uses the precise electron circuit and good productive technology,
which is the metal structure machine of fingerprint & card access. It is
widely used in business organization, office, factory, housing district etc.
COM
The product uses remote controller or Admin fingerprints for programming,
support fingerprints and EM 125Khz card, easy to install and program.

2. Feature

Feature Description NC

Metal Shell Durable, anti-vandal

Ultra-low Power Long-lived, performance stable, standby current

Consumption is less than 30mA
Touch Sensor Fingerprint recognition is very fast
activated
Capacity 200 fingerprints & 500 cards (1000 fingerprints &
2000 cards can be selected)
Used as a Card Can be used as a card reader with Wiegand26
Reader output
Used as a Standalone Can connect external EM/Mifare/HID wiegand26
Controller card reader

3. Installation
Drill the hole according to the size of the product and fix the bottom shell with
the equipped screws. Thread the lead wire out of the outlet hole of the bottom
shell, connect the lead wire according to the function required, and wrap the
unused wires to avoid short circuit. After wire connected, fix the front shell to
the bottom shell and turn the screws well, installation is finished.
(see figure below)
1
Note: After all wires are connected, please check carefully whether they
are connected correctly, then turn on the electricity after confirmation.

LED
COM

Fingerprint
reader

NC

Infrared Remote Control Window

Installation drawing

4. Wiring

No. Color Function Description

1 Green D0 Wiegand Output D0
2 White D1 Wiegand Output D1
3 Grey Alarm Alarm Negative
4 Yellow Open Request to Exit Button
5 Brown D_IN Door Contact
6 Red +12V (+) 12VDC Positive Regulated Power Input
7 Black GND (-) Negative Regulated Power Input
8 Blue NO Relay NO
9 Purple COM COM
10 Orange NC Relay NC
11 Pink GND One Terminal of Factory Default Setting
12 Pink RESET The other Terminal of Factory Default Setting

2
5. Connection Diagram
5.1 Common Power Supply

COM

NC

5.2 Special Power Supply

COM

NC

3
7. Admin Operation
7.1 Enter into Programming Mode
Press * Admin Code # Factory default: 888888
Remark: All of steps below(7.2-7.9) must be done after entering into programming mode.

7.2 Revise Admin Code

Press 0 New Admin Code # New Admin Code #
Remark: Admin code is 6~8 digital No.
7.3 Add Users
7.3.1 Add Users Continuously
Press 1 User Fingerprint twice # or card # or the Card No (8 digit) # … #
Remark: 200 fingerprint users, ID is 3-200, 500 card users, ID is 1001-1500, ID is
produced automatically and automatic accumulation.
Note: Select 1000 fingerprints & 2000 cards, Fingerprint user ID is 3~1000, Card user
ID is 1001~3000,ID is produced automatically and automatic accumulation.
COM

7.3.2 Add Users by Appointed ID No

Press 1 ID No # User Fingerprint twice # or card # or Card No (8 digit) # … #
Remark: ID 1 is Admin Add Fingerprint, ID 2 is Admin
NC Delete Fingerprint, pressing
# in the process of operating means confirmation, the final # means closing setting
mode, pressing * means exiting programme mode.

7.3.3 Add Users by Admin Fingerprint or Admin Card

Press Admin Add Fingerprint or Admin Add Card , 1st User Fingerprint Twice
2nd User Fingerprint Twice or 1st card 2nd card or Admin Add Fingerprint
or Admin Add Card , exit programme mode.
7.4 Delete Users
7.4.1 Delete Users by Fingerprint/Card/Card No
Press 2 User Fingerprint twice # or card # or the Card No (8 digit) # … #

7.4.2 Delete Users by Appointed ID No

5
Press 2 ID No 1 # ID No 2 # ... #

7.4.3 Delete All Users

Press 20000 #
Remark: All of fingerprints and user will be deleted, but Admin Card won’t be deleted,
please use it prudently.
7.4.4 Delete Users by Admin Fingerprint or Admin Card
Press Admin Delete Fingerprint or Admin Delete Card, 1st User Fingerprint Twice
2nd User Fingerprint Twice … 1st card 2nd card ... Admin Delete Fingerprint or
Admin Delete Card , exit programme mode.

7.5 Set Facility Code

Press 3 0~255 #
Remark: If used as a card reader, please set it. Facility code and ID No make up
virtual card No, data will be transmitted by wiegand26 when inputting fingerprint.
For example, if facility code is 255, fingerprint ID No is 3, then virtual card No is
255,00003. The function only applies to ID No of simulate 8 digit decimalism, and
the virtual card No is displayed on the machine with wiegand26 format.

7.6 Set Door Relay Time

Press 5 0~99s # Factory default: 5 seconds

7.7 Set Alarm Time

Press 9 0~3m # Factory default: 1 minute

7.8 Set Door Open Detection

7.8.1 Disable the function (Factory default setting)

Press 6 0 #

7.8.2 Enable the function

Press 6 1 #

When enable this function

6
7.8.2.1 If open the door normally,but don’t close it after 1 minute, the inside
Buzzer will alarm automatically, the alarm will stop after closing the door.
7.8.2.2 If the door is opened forcibly, or the door isn’t opened within 120 seconds
after lock is released, the inside Buzzer and outside alarm will be activated.
7.9 Set Security Mode

7.9.1 Normal Mode(Factory default setting)

Press 7 0 #

7.9.2 Locked Mode

Press 7 1 #
The device will be locked for 10 minutes if input 10times invalid fingerprints or
cards continuously within 10 minutes.

7.9.3 Alarm Mode

Press 7 2 #
Inside beep and outside alarm will be activated if input 10times invalid fingerprints
or cards continuously within 10 minutes.

8. User Operation

8.1 Open the Door by Fingerprint

Press User Fingerprint Valid fingerprint to open the door.

8.2 Open the Door by Card

Read User card Valid card to open the door.

8.3 Remove Alarm

Press Valid User Fingerprint or Card or Admin Fingerprint or Card or Admin Code
# ,then alarm is removed.

7
5.3 Used as a Card Reader

COM

NC

6. Reset to Factory Default

Power off, press the RESET key (SW14) continuously on the PCB, then power
on, release it until hearing short beeps twice.
Note: If Waterproof devices, power off, pink wire connects pink wire, then power
on, take apart it until hearing short beeps twice.
The LED turns orange, then read any two EM cards, the first one is Admin Add
Card, the second one is Admin Delete Card, old Admin cards are covered by
new one, or without setting Admin cards within 10 seconds, then the LED turns
red flash, it means factory default setting is successful.
Remark: Reset to factory default setting, the users’ information enrolled are still
retained.

4
COM
9. Sound and Light Indication

Operation Fingerprint
Status LED Color Sensor Buzzer
Reset to Factory Orange Off Short Ring twice
Default setting
Sleeping Mode Red Slow Off

Stand by Red Slow On

Valid Keys Long Ring once

Enter into
Programming Mode Red Off Long Ring once
Exit Programming Red Slow On Long Ring once
Mode
Wrong Operation Short Ring 3 times

Open the Door Green Off Long Ring once

Alarm Red Quick Off Alarm

10. Technical Specification

Operation Voltage DC+12V±10%
Idle Current ≤20mA
Standby Current ≤80mA
Card Reading Distance ≥2cm
Operating Temperature -20～+50℃
Operating Humidity 20%RH-95%RH
Resolution 450 DPI
Fingerprint Input Time <1S
Identification Time <1S
FAR <0.0000256%
FRR <0.0198%
Structure Zinc Alloy

8
11. Packing list

Article Model Quantity Remark

Fingerprint
Access Control 1
Infrared
Remote Control 1

Admin Card Add/Delete 2 Admin Delete Card

&Delete Card

User Manual 1

Security Screws 1 To fix the device to

( Φ3*7.5mm) the back cover
Special Screw Φ20mm×60mm 1
Driver
Self tapping Φ4mm×25mm Used for fixing
screws 4

Pastern stopper Φ6mm×28mm 4 Used for fixing