YASKAWA AC Drive-V1000

Compact Vector Control Drive

Installation & Start-Up Manual
Type: CIMR-VU Receiving 1
Models: 200 V Class, Three-Phase Input: 0.1 to 18.5 kW
200 V Class, Single-Phase Input: 0.1 to 3.0 kW Mechanical
400 V Class, Three-Phase Input: 0.2 to 18.5 kW Installation 2
To properly use the product, read this manual thoroughly Electrical
and retain for easy reference, inspection, and maintenance. Installation 3
Ensure the end user receives this manual.
Start-Up Programming
& Operation 4
Troubleshooting 5
Periodic Inspection
& Maintenance 6
Peripheral Devices
& Options 7
Specifications A
Parameter List B
Network
Communications C
Standards
Compliance D

MANUAL NO. TOEP C710606 22A

2 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 Table of
Contents
i. PREFACE & GENERAL SAFETY ................................ 11
i.1 Preface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Applicable Documentation . . . . . . . . . . . . . . . . . . . . . . . . . 12
Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Terms and Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . 13
i.2 General Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Supplemental Safety Information . . . . . . . . . . . . . . . . . . . . 14
Safety Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Drive Label Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Warranty Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Quick Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

1. RECEIVING ................................................................... 23
1.1 Section Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
1.2 Model Number and Nameplate Check . . . . . . . . . 25
Nameplate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
1.3 Drive Models and Enclosure Types . . . . . . . . . . . 28

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 3
 1.4 Component Names . . . . . . . . . . . . . . . . . . . . . . . . 30
IP20/Open-Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
IP20/NEMA Type 1 Enclosure . . . . . . . . . . . . . . . . . . . . . . 32
Front Views . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

2. MECHANICAL INSTALLATION ................................... 37

2.1 Section Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
2.2 Mechanical Installation . . . . . . . . . . . . . . . . . . . . . 41
Installation Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Installation Orientation and Spacing . . . . . . . . . . . . . . . . . . 42
Removing and Attaching the Protective Covers . . . . . . . . . 44
Exterior and Mounting Dimensions . . . . . . . . . . . . . . . . . . 44

3. ELECTRICAL INSTALLATION..................................... 51
3.1 Section Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
3.2 Standard Connection Diagram . . . . . . . . . . . . . . . 55
3.3 Main Circuit Connection Diagram . . . . . . . . . . . . 58
Single-Phase 200 V Class (CIMR-V BA0001 ~ 0012) . . . 58
Three-Phase 200 V Class (CIMR-V 2A0001 ~ 0069)
Three-Phase 400 V Class (CIMR-V 4A0001 ~ 0038) . . . 58
3.4 Terminal Block Configuration. . . . . . . . . . . . . . . . 59
3.5 Protective Covers . . . . . . . . . . . . . . . . . . . . . . . . . 60
IP20/Open-Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
IP20/NEMA Type 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
3.6 Main Circuit Wiring . . . . . . . . . . . . . . . . . . . . . . . . 63
Main Circuit Terminal Functions . . . . . . . . . . . . . . . . . . . . . 63
Wire Gauges and Tightening Torque . . . . . . . . . . . . . . . . . 63
Main Circuit Terminal Power Supply and Motor Wiring . . . 66
3.7 Control Circuit Wiring . . . . . . . . . . . . . . . . . . . . . . 69
Control Circuit Terminal Block Functions . . . . . . . . . . . . . . 70
Removable Terminal Block Configuration . . . . . . . . . . . . . 72

4 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 Wiring Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
3.8 I/O Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Sinking/Sourcing Mode Switch . . . . . . . . . . . . . . . . . . . . . 77
3.9 Main Frequency Reference . . . . . . . . . . . . . . . . . . 79
Terminal A2 Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
3.10 MEMOBUS/Modbus Termination. . . . . . . . . . . . . 81
3.11 Braking Resistor . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
3.12 Wiring Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . 84

4. START-UP PROGRAMMING & OPERATION ............. 87

4.1 Section Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
4.2 Using the Digital LED Operator . . . . . . . . . . . . . . . 91
Keys, Displays, and LEDs . . . . . . . . . . . . . . . . . . . . . . . . . 91
Digital Text Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
LED Screen Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
LO/RE LED and RUN LED Indications . . . . . . . . . . . . . . . 94
Menu Structure for Digital LED Operator . . . . . . . . . . . . . 96
4.3 The Drive and Programming Modes . . . . . . . . . . . 97
Navigating the Drive and Programming Modes . . . . . . . . 98
Changing Parameter Settings or Values . . . . . . . . . . . . . 102
Verifying Parameter Changes: Verify Menu . . . . . . . . . . 102
Switching Between LOCAL and REMOTE . . . . . . . . . . . 103
Parameters Available in the Setup Group . . . . . . . . . . . . 104
4.4 Start-up Flowcharts . . . . . . . . . . . . . . . . . . . . . . . 106
Flowchart A: Basic Start-Up and Motor Tuning . . . . . . . . 107
Subchart A1: Simple Motor Set-Up with
Energy Savings or Speed Search using V/f Mode . . . . . 108
Subchart A2: High Performance Operation
Using Open Loop Vector Motor Control . . . . . . . . . . . . . 109
Subchart A3: Operation with Permanent Magnet Motors 110

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 5
 4.5 Application Presets . . . . . . . . . . . . . . . . . . . . . . . 111
Application Preset Function (APPL) . . . . . . . . . . . . . . . . . 111
Application Presets: A1-06 . . . . . . . . . . . . . . . . . . . . . . . . 111
User Parameters: A2-01 to A2-32 . . . . . . . . . . . . . . . . . . 120
User Parameter Automatic Selection: A2-33 . . . . . . . . . . 120
4.6 Basic Drive Setup Adjustments . . . . . . . . . . . . . 122
Control Mode Selection: A1-02 . . . . . . . . . . . . . . . . . . . . 122
Initialize Parameter Values: A1-03 . . . . . . . . . . . . . . . . . . 122
Application Presets: A1-06 . . . . . . . . . . . . . . . . . . . . . . . . 123
DWEZ Function Selection: A1-07 . . . . . . . . . . . . . . . . . . . 124
Frequency Reference Source: b1-01 . . . . . . . . . . . . . . . . 124
Run Command Input Selection: b1-02 . . . . . . . . . . . . . . . 127
Stopping Method Selection: b1-03 . . . . . . . . . . . . . . . . . . 129
Acceleration/Deceleration: C1-01 to C1-11 . . . . . . . . . . . 132
Drive Duty Mode and Carrier Frequency Selection:
C6-01 and C6-02 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
Drive Input Voltage Setting: E1-01 . . . . . . . . . . . . . . . . . . 138
V/f Pattern Selection: E1-03 . . . . . . . . . . . . . . . . . . . . . . . 139
Motor Parameters: E2-01 through E2-12
(Manually Entering Parameter Settings) . . . . . . . . . . . . . 142
Digital Outputs H2-01 to H2-03 . . . . . . . . . . . . . . . . . . . . 144
Analog Outputs: H4-01 to H4-03 . . . . . . . . . . . . . . . . . . . 144
Motor Protection: L1-01 and L1-02 . . . . . . . . . . . . . . . . . . 146
Drive Status Monitors: U1-01 to U6-19 . . . . . . . . . . . . . . 150
4.7 Test Run . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
Powering Up the Drive and Operation Status Display . . . 153
Auto-Tuning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
No-Load Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
Operating with the Load Connected . . . . . . . . . . . . . . . . . 163
Verifying Parameter Settings and Backing Up Changes . 163
Jog Operation: FJOG/RJOG . . . . . . . . . . . . . . . . . . . . . . 166
Multi-Step Speed Operation (4-Step Speed) . . . . . . . . . . 168
4.8 Test Run Checklist. . . . . . . . . . . . . . . . . . . . . . . . 171

6 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 5. TROUBLESHOOTING ................................................ 173
5.1 Section Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174
5.2 Motor Performance Fine Tuning . . . . . . . . . . . . . 177
V/f Motor Control Method Tuning . . . . . . . . . . . . . . . . . . 177
Open Loop Vector (OLV) Motor Control Method Tuning 178
Motor Hunting and Oscillation Control Parameters . . . . . 180
5.3 Drive Alarms, Faults, and Errors . . . . . . . . . . . . . 181
Types of Alarms, Faults, and Errors . . . . . . . . . . . . . . . . 181
Alarm and Error Displays . . . . . . . . . . . . . . . . . . . . . . . . 182
5.4 Fault Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . 187
Fault Displays, Causes, and Possible Solutions . . . . . . . 187
5.5 Alarm Detection . . . . . . . . . . . . . . . . . . . . . . . . . . 206
Alarm Codes, Causes, and Possible Solutions . . . . . . . . 206
5.6 Operator Programming Errors. . . . . . . . . . . . . . . 217
oPE Codes, Causes, and Possible Solutions . . . . . . . . . 217
5.7 Auto-Tuning Fault Detection . . . . . . . . . . . . . . . . 222
Auto-Tuning Codes, Causes, and Possible Solutions . . 222
5.8 Diagnosing and Resetting Faults . . . . . . . . . . . . 226
Fault Occurs Simultaneously with Power Loss . . . . . . . . 226
If the drive still has power after a fault occurs . . . . . . . . . 226
Viewing Fault Trace Data after Fault . . . . . . . . . . . . . . . 227
Fault Reset Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . 227
5.9 Troubleshooting without Fault Display . . . . . . . 228
Cannot Change Parameter Settings . . . . . . . . . . . . . . . . 228
Motor Does Not Rotate Properly after Pressing
RUN Button or After Entering External Run Command . 228

6. PERIODIC INSPECTION & MAINTENANCE .......... 243

6.1 Section Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . 244

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 7
 6.2 Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 247
Recommended Daily Inspection . . . . . . . . . . . . . . . . . . . . 248
Recommended Periodic Inspection . . . . . . . . . . . . . . . . . 249
6.3 Periodic Maintenance . . . . . . . . . . . . . . . . . . . . . 252
Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 252
6.4 Drive Cooling Fans . . . . . . . . . . . . . . . . . . . . . . . 254
Cooling Fan Replacement . . . . . . . . . . . . . . . . . . . . . . . . 254
6.5 Drive Replacement. . . . . . . . . . . . . . . . . . . . . . . . 258
Serviceable Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 258
Terminal Board Overview . . . . . . . . . . . . . . . . . . . . . . . . . 258
Replacing the drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 259
Details on Terminal Board (TB) or Control Board
(CNT) Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 262

7. PERIPHERAL DEVICES & OPTIONS ....................... 265

7.1 Section Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . 266
7.2 Peripheral Devices. . . . . . . . . . . . . . . . . . . . . . . . 269
7.3 Connecting Peripheral Devices . . . . . . . . . . . . . 270
7.4 Installing Peripheral Devices . . . . . . . . . . . . . . . 271
Installing a Molded Case Circuit Breaker (MCCB) . . . . . . 271
Installing a Leakage Breaker . . . . . . . . . . . . . . . . . . . . . . 272
Installing a Magnetic Contactor . . . . . . . . . . . . . . . . . . . . 272
Connecting an AC or DC Reactor . . . . . . . . . . . . . . . . . . 273
Connecting a Surge Protector . . . . . . . . . . . . . . . . . . . . . 274
Connecting a Noise Filter . . . . . . . . . . . . . . . . . . . . . . . . . 274
EMC Filter Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 278
Installing a Motor Thermal Overload (OL)
Relay on the Drive Output . . . . . . . . . . . . . . . . . . . . . . . . 282
7.5 Communication Options . . . . . . . . . . . . . . . . . . . 285
7.6 Connecting an Option Card . . . . . . . . . . . . . . . . 286
Verifying Option Card and Product Type . . . . . . . . . . . . . 286
Connecting the Option Card . . . . . . . . . . . . . . . . . . . . . . . 287

8 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 A. SPECIFICATIONS....................................................... 291
A.1 Heavy Duty and Normal Duty Ratings . . . . . . . . 292
A.2 Single/Three-Phase 200 V Class Drive . . . . . . . . 293
A.3 Three-Phase 400 V Class Drives. . . . . . . . . . . . . 296
A.4 Drive Specifications . . . . . . . . . . . . . . . . . . . . . . . 298
A.5 Drive Watts Loss Data . . . . . . . . . . . . . . . . . . . . . 302
A.6 Drive Derating Data . . . . . . . . . . . . . . . . . . . . . . . 305
Carrier Frequency Derating . . . . . . . . . . . . . . . . . . . . . . 305
Temperature Derating . . . . . . . . . . . . . . . . . . . . . . . . . . . 305
Altitude Derating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 306

B. PARAMETER LIST ..................................................... 309

B.1 Parameter Groups . . . . . . . . . . . . . . . . . . . . . . . . 310
B.2 Parameter Table . . . . . . . . . . . . . . . . . . . . . . . . . . 311
A: Initialization Parameters . . . . . . . . . . . . . . . . . . . . . . . 311
b: Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 312
C: Tuning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 320
d: References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 325
E: Motor Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . 330
F: Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 336
H Parameters: Multi-Function Terminals . . . . . . . . . . . . 340
L: Protection Function . . . . . . . . . . . . . . . . . . . . . . . . . . . 352
n: Advanced Performance Set-Up . . . . . . . . . . . . . . . . . 366
o: Operator Related Parameters . . . . . . . . . . . . . . . . . . . 370
r: DWEZ Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . 373
T: Motor Tuning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 375
U: Monitors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 376
Control Mode Dependent Parameter Default Values . . . 387
V/f Pattern Default Values . . . . . . . . . . . . . . . . . . . . . . . . 389
Default Settings Determined by Drive Capacity
(o2-04) and ND/HD Selection (C6-01) . . . . . . . . . . . . . . 390
Parameters that Change with the Motor Code Selection 401

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 9
 C. NETWORK COMMUNICATIONS................................ 405
C.1 MEMOBUS/Modbus Basic Set-Up . . . . . . . . . . . 406
MEMOBUS/Modbus Communication Configuration . . . . . 406
Communication Specifications . . . . . . . . . . . . . . . . . . . . . 407
Communication Connection Terminal . . . . . . . . . . . . . . . 407
Communication Set-Up Procedure . . . . . . . . . . . . . . . . . . 409

D. STANDARDS COMPLIANCE ..................................... 413

D.1 Section Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . 414
D.2 European Standards . . . . . . . . . . . . . . . . . . . . . . 417
CE Low Voltage Directive Compliance . . . . . . . . . . . . . . . 417
EMC Guidelines Compliance . . . . . . . . . . . . . . . . . . . . . . 419
D.3 UL Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . 425
UL Standards Compliance . . . . . . . . . . . . . . . . . . . . . . . . 425
Drive Motor Overload Protection . . . . . . . . . . . . . . . . . . . 428
D.4 Safe Disable Input Precautions . . . . . . . . . . . . . 431
Safe Disable Function Description . . . . . . . . . . . . . . . . . . 431
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 431
D.5 User Setting Table. . . . . . . . . . . . . . . . . . . . . . . . 433

INDEX .......................................................................... 443

10 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 i
Preface &
General Safety
This section provides safety messages pertinent to this product,
that, if not heeded, may result in fatality, personal injury, or
equipment damage. Yaskawa is not responsible for the
consequences of ignoring these instructions.

I.1 PREFACE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
I.2 GENERAL SAFETY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 11
i.1 Preface

i.1 Preface
Yaskawa manufactures products used as components in a wide variety of industrial systems
and equipment. The selection and application of Yaskawa products remain the responsibility
of the equipment manufacturer or end user. Yaskawa accepts no responsibility for the way its
products are incorporated into the final system design. Under no circumstances should any
Yaskawa product be incorporated into any product or design as the exclusive or sole safety
control. Without exception, all controls should be designed to detect faults dynamically and
fail safely under all circumstances. All systems or equipment designed to incorporate a
product manufactured by Yaskawa must be supplied to the end user with appropriate
warnings and instructions as to the safe use and operation of that part. Any warnings
provided by Yaskawa must be promptly provided to the end user. Yaskawa offers an express
warranty only as to the quality of its products in conforming to standards and specifications
published in the Yaskawa manual. NO OTHER WARRANTY, EXPRESS OR IMPLIED, IS
OFFERED. Yaskawa assumes no liability for any personal injury, property damage, losses,
or claims arising from misapplication of its products.

◆ Applicable Documentation
The following manuals are available for V1000 series drives:

V1000 Series AC Drive Installation & Start-Up Manual

Read this manual first.
This manual describes installation, wiring, operation procedures, functions,
troubleshooting, maintenance, and inspections to perform before operation.
STOP

V1000 Series AC Drive Technical Manual

Read this manual for detailed information about parameter usage. Contact a
V1000
Yaskawa representative to order this manual.
๟ᵄᢙᜰ઎
ᱜォㅒォㆬᛯ
಴ജ๟ᵄᢙ



(Hz)

(Hz)
V1000 Series AC Drive Quick Start Guide
಴ജ㔚ᵹ  (A)
಴ജ㔚࿶  (V)

This guide is packaged together with the product. It contains basic

ࡕ࠾࠲ 
ࡌ࡝ࡈࠔࠗ 
࠮࠶࠻ࠕ࠶ࡊ 
ࡄ࡜ࡔ࡯࠲⸳ቯ 
ࠝ࡯࠻࠴ࡘ࡯࠾ࡦࠣ 
information required to install and wire the drive. This guide provides basic
ෂ‫ޓ‬㒾 ߌ߇㧚ᗵ㔚ߩ߅ߘࠇ߇޽ࠅ߹ߔ‫ޕ‬
ᝪ߃ઃߌ‫ޔ‬ㆇォߩ೨ߦߪᔅߕขᛒ⺑᣿ᦠࠍ⺒߻ߎߣ‫ޕ‬
ㅢ㔚ਛ߅ࠃ߮㔚Ḯㆤᢿᓟ5 ಽએౝߪࡈࡠࡦ࠻ࠞࡃ࡯ࠍ
programming and simple set-up and adjustment. Refere to the V1000
ᄖߐߥ޿ߎߣ‫ޕ‬
400V ⚖ࠗࡦࡃ࡯࠲ߩ႐วߪ‫ޔ‬㔚Ḯߩਛᕈὐ߇ធ࿾
ߐࠇߡ޿ࠆߎߣࠍ⏕⹺ߔࠆߎߣ‫ޕ‬㧔‫ޓޓ‬ኻᔕ㧕
Technical Manual for complete descriptions of drive features and functions.

◆ Symbols
NOTE: indicates a supplement or precaution that does not cause drive damage.

TERMS Indicates a term or definition used in this manual.

12 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 t
i.1 Preface

◆ Terms and Abbreviations

Preface & General Safety

Drive: Yaskawa V1000 Series Drive
TERMS PM motor: Synchronous motor (an abbreviation for IPM motor or SPM motor)
IPM motor: SSR1 Series
SPM motor: Pico motor (SMRA Series)

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 13
i.2 General Safety

i.2 General Safety

◆ Supplemental Safety Information

General Precautions
• The diagrams in this manual may be indicated without covers or safety shields to show details.
Restore covers or shields before operating the drive and run the drive according to the instructions
described in this manual.
• Any illustrations, photographs, or examples used in this manual are provided as examples only and
may not apply to all products to which this manual is applicable.
• The products and specifications described in this manual or the content and presentation of the
manual may be changed without notice to improve the product and/or the manual.
• When ordering a new copy of the manual due to damage or loss, contact your Yaskawa
representative or the nearest Yaskawa sales office and provide the manual number shown on the
front cover.
• If nameplate becomes worn or damaged, order a replacement from your Yaskawa representative or
the nearest Yaskawa sales office.

WARNING
Read and understand this manual before installing, operating or servicing
this drive. The drive must be installed according to this manual and local
codes.
The following conventions are used to indicate safety messages in this
manual. Failure to heed these messages could result in serious or possibly
even fatal injury or damage to the products or to related equipment and
systems.

DANGER
Indicates a hazardous situation, which, if not avoided, will result in
death or serious injury.

14 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 t
i.2 General Safety

\
WARNING

Preface & General Safety

Indicates a hazardous situation, which, if not avoided, could result in
death or serious injury.

WARNING! will also be indicated by a bold key word embedded in the text followed by an italicized safety
message.

CAUTION
Indicates a hazardous situation, which, if not avoided, could result in i
minor or moderate injury.

CAUTION! will also be indicated by a bold key word embedded in the text followed by an italicized safety
message.

NOTICE
Indicates a property damage message.

NOTICE: will also be indicated by a bold key word embedded in the text followed by an italicized safety
message.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 15
i.2 General Safety

◆ Safety Messages
DANGER
Heed the safety messages in this manual.
Failure to comply will result in death or serious injury.
The operating company is responsible for any injuries or equipment
damage resulting from failure to heed the warnings in this manual.

Electrical Shock Hazard

Do not connect or disconnect wiring while the power is on.
Failure to comply will result in death or serious injury.
Before servicing, disconnect all power to the equipment. The internal
capacitor remains charged even after the power supply is turned off. The
charge indicator LED will extinguish when the DC bus voltage is below 50
Vdc. To prevent electric shock, wait at least five minutes after all indicators
are OFF and measure the DC bus voltage level to confirm safe level.

WARNING
Sudden Movement Hazard
System may start unexpectedly upon application of power, resulting in
death or serious injury.
Clear all personnel from the drive, motor and machine area before applying
power. Secure covers, couplings, shaft keys and machine loads before
applying power to the drive.

When using DriveWorksEZ to create custom programming, the drive

I/O terminal functions change from factory settings and the drive will
not perform as outlined in this manual.
Unpredictable equipment operation may result in death or serious injury.
Take special note of custom I/O programming in the drive before
attempting to operate equipment.

16 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 t
i.2 General Safety

WARNING

Preface & General Safety

Electrical Shock Hazard
Do not attempt to modify or alter the drive in any way not explained in
this manual.
Failure to comply could result in death or serious injury.
Yaskawa is not responsible for any modification of the product made by the
user. This product must not be modified.

Do not allow unqualified personnel to use equipment. i

Failure to comply could result in death or serious injury.
Maintenance, inspection, and replacement of parts must be performed only
by authorized personnel familiar with installation, adjustment and
maintenance of AC drives.

Do not remove covers or touch circuit boards while the power is on.
Failure to comply could result in death or serious injury.

Fire Hazard
Do not use an improper voltage source.
Failure to comply could result in death or serious injury by fire.
Verify that the rated voltage of the drive matches the voltage of the
incoming power supply before applying power.

CAUTION
Crush Hazard
Do not carry the drive by the front cover.
Failure to comply may result in minor or moderate injury from the main
body of the drive falling.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 17
i.2 General Safety

NOTICE
Observe proper electrostatic discharge procedures (ESD) when
handling the drive and circuit boards.
Failure to comply may result in ESD damage to the drive circuitry.

Never connect or disconnect the motor from the drive while the drive
is outputting voltage.
Improper equipment sequencing could result in damage to the drive.

Do not perform a withstand voltage test on any part of the drive.

Failure to comply could result in damage to the sensitive devices within the
drive.

Do not operate damaged equipment.

Failure to comply could result in further damage to the equipment.
Do not connect or operate any equipment with visible damage or missing
parts.

Install adequate branch circuit short circuit protection per applicable

codes.
Failure to comply could result in damage to the drive.
The drive is suitable for circuits capable of delivering not more than 30,000
RMS symmetrical Amperes, 240 Vac maximum (200V Class) and 480 Vac
maximum (400V Class).

Do not expose the drive to halogen group disinfectants.

Failure to comply may cause damage to the electrical components in the
drive.
Do not pack the drive in wooden materials that have been fumigated or
sterilized.
Do not sterilize the entire package after the product is packed.

18 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 t
i.2 General Safety

◆ Drive Label Warnings

\
Always heed the warning information listed in Figure i.1 in the position shown in

Preface & General Safety

Figure i.2.
Figure i.1

WARNING Risk of electric shock.

Read manual before installing.
Wait 5 minutes for capacitor discharge after
disconnecting power supply.
To conform to requirements, make sure
to ground the supply neutral for 400V class.
i
Figure i.1 Warning Information
Figure i.2

STOP

V1000
๟ᵄᢙᜰ઎  (Hz)
ᱜォㅒォㆬᛯ 
಴ജ๟ᵄᢙ  (Hz)
಴ജ㔚ᵹ  (A)
಴ജ㔚࿶  (V)
ࡕ࠾࠲ 
ࡌ࡝ࡈࠔࠗ 
࠮࠶࠻ࠕ࠶ࡊ 
ࡄ࡜ࡔ࡯࠲⸳ቯ 
ࠝ࡯࠻࠴ࡘ࡯࠾ࡦࠣ 

ෂ‫ޓ‬㒾 ߌ߇㧚ᗵ㔚ߩ߅ߘࠇ߇޽ࠅ߹ߔ‫ޕ‬
ᝪ߃ઃߌ‫ޔ‬ㆇォߩ೨ߦߪᔅߕขᛒ⺑᣿ᦠࠍ⺒߻ߎߣ‫ޕ‬
ㅢ㔚ਛ߅ࠃ߮㔚Ḯㆤᢿᓟ5 ಽએౝߪࡈࡠࡦ࠻ࠞࡃ࡯ࠍ
ᄖߐߥ޿ߎߣ‫ޕ‬
Warning
400V ⚖ࠗࡦࡃ࡯࠲ߩ႐วߪ‫ޔ‬㔚Ḯߩਛᕈὐ߇ធ࿾
ߐࠇߡ޿ࠆߎߣࠍ⏕⹺ߔࠆߎߣ‫ޕ‬㧔‫ޓޓ‬ኻᔕ㧕 Display
Figure i.2 Warning Information Position

◆ Warranty Information
■ Restrictions
The V1000 was not designed or manufactured for use in devices or systems that may
directly affect or threaten human lives or health.
Customers who intend to use the product described in this manual for devices or systems
relating to transportation, health care, space aviation, atomic power, electric power, or in

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 19
i.2 General Safety

underwater applications must first contact their Yaskawa representatives or the nearest
Yaskawa sales office.
This product has been manufactured under strict quality-control guidelines. However, if this
product is to be installed in any location where failure of this product could involve or result
in a life-and-death situation or loss of human life or in a facility where failure may cause a
serious accident or physical injury, safety devices must be installed to minimize the
likelihood of any accident.

◆ Quick Reference
Easily Set Application-Specific Parameters

Preset parameter defaults are available for many applications. Refer to 2WOR
Application Presets on page 111

(CP %QPXG[QT

Run a Motor of One-Frame Larger Capacity

When using this drive for variable torque loads such as fans and pumps, a motor one frame size larger can be used.
Refer to Drive Duty Mode Selection: C6-01 on page 134

Know the Details of Safety Measures

The functions listed below affect the safe operation of the drive. Ensure that the settings fit the application
requirements prior to operation.
Operation of digital outputs during Auto-tuning. Rotational Auto-tuning allows for normal digital output
operation, while non-rotational Auto-tuning does not allow for normal digital output operation.
Safe operations. Run by power on. Parameter setting b1-17.
LOCAL/REMOTE key effective during stop in drive mode. Parameter o2-01.
LED operator stop key priority selection. Parameter o2-02.
Enter press required after changing the keypad frequency refrence. Parameter o2-05.
Operation interlock when program mode is selected. Parameter b1-08.

20 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 t
i.2 General Safety

\
Replace the Drive

Preface & General Safety

The removable terminal block with parameter backup function allows the
transfer of parameter settings after drive replacement. Refer to Replacing the
drive on page 259

Drive a Synchronous PM Motor

i
The V1000 drive can opertate synchronous PM motors. Refer to Subchart A3:
Operation with Permanent Magnet Motors on page 110.

Perform Auto-tuning
Automatic tuning sets motor parameters. Refer to Auto-Tuning on page 153

Check the Maintenance Period Using Drive Monitors

The maintenance period of fans and capacitors can be checked drive monitors. Refer to Performance Life Monitors
on page 252.

Drive or Motor Faults are Displayed on a Digital Operator

Refer to Fault Displays, Causes, and Possible Solutions on page 187 and Refer to Alarm Codes, Causes, and
Possible Solutions on page 206.

Standards Compliance

Refer to CE Low Voltage Directive Compliance on page 417 and Refer to UL

C UL US
Standards Compliance on page 425. R

LISTED

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 21
i.2 General Safety

22 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 1
Receiving
This chapter describes the proper inspections to perform after
receiving the drive and illustrates the different enclosure types
and components.

1.1 SECTION SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

1.2 MODEL NUMBER AND NAMEPLATE CHECK. . . . . . . . . 25
1.3 DRIVE MODELS AND ENCLOSURE TYPES . . . . . . . . . . 28
1.4 COMPONENT NAMES . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 23
1.1 Section Safety

1.1 Section Safety

CAUTION
Do not carry the drive by the front cover.
Failure to comply may cause the main body of the drive to fall, resulting in
minor or moderate injury.

NOTICE
Observe proper electrostatic discharge procedures (ESD) when
handling the drive and circuit boards.
Failure to comply may result in ESD damage to the drive circuitry.

A motor connected to a PWM drive may operate at a higher

temperature than a utility-fed motor and the operating speed range
may reduce motor cooling capacity.
Ensure that the motor is suitable for inverter duty and/or the motor service
factor is adequate to accommodate the additional heating with the intended
operating conditions.

24 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 1.2 Model Number and Nameplate Check

1.2 Model Number and Nameplate Check

Please perform the following tasks after receiving the drive:
• Inspect the drive for damage.

Receiving
If the drive appears damaged upon receipt, contact the shipper immediately.
• Verify receipt of the correct model by checking the information on the nameplate.
• If you have received the wrong model or the drive does not function properly, contact
your supplier.
1
◆ Nameplate
Figure 1.1

Normal Duty Amps/Heavy Duty Amps

AC drive model %+/487#(##4'8#

Input specifications #%2*8*\#
Output specifications #%2*8*\##

Lot number Software version
Serial number
Enclosure Type

+056#..#6+10%#6')14;++ PASS

#UUGODNGFKP75# RoHS

Figure 1.1 Nameplate Information

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 25
1.2 Model Number and Nameplate Check

CIMR- V U 2 A 0001 B A A
Drive V1000 Customized Voltage Design
No. No.
Series Specifications Class Revision
A Standard model A IP00 Order
No. Region
Code B IP20
U USA
F IP20
A Japan
Environmental
No.
C Europe Specification *
A Standard
No. Voltage Class M Humidity- and
B 1-phase, 200-240 Vac dust-resistant
N Oil-resistant
2 3-phase, 200-240 Vac S Vibration-resistant
4 3-phase, 380-480 Vac

Single-Phase 200 V

Normal Duty Heavy Duty

Max. Motor Rated Output Max. Motor Rated Output
No. No.
Capacity kW Current A Capacity kW Current A
0001 0.2 1.2 0001 0.1 0.8
0002 0.4 1.9 0002 0.2 1.6
0003 0.75 3.3 0003 0.4 3
0006 1.1 6 0006 0.75 5
0010 2.2 9.6 0010 1.5 8
0012 3.0 12 0012 2.2 11

Three-Phase 200 V

Normal Duty Heavy Duty

Max. Motor Rated Output Max. Motor Rated Output
No. No.
Capacity kW Current A Capacity kW Current A
0001 0.2 1.2 0001 0.1 0.8
0002 0.4 1.9 0002 0.2 1.6
0004 0.75 3.5 0004 0.4 3

26 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 1.2 Model Number and Nameplate Check

Normal Duty Heavy Duty

0006 1.1 6 0006 0.75 5
0010 2.2 9.6 0010 1.5 8
0012 3.0 12 0012 2.2 11

Receiving
0020 5.5 19.6 0020 3.7 17.5
0030 7.5 30 0030 5.5 25
0040 11 40 0040 7.5 33
0056 15 56 0056 11 47
0069 18.5 69 0069 15 60 1
Three-Phase 400 V

Normal Duty Heavy Duty

Max. Motor Rated Output Max. Motor Rated Output
No. No.
Capacity kW Current A Capacity kW Current A
0001 0.4 1.2 0001 0.2 1.2
0002 0.75 2.1 0002 0.4 1.8
0003 1.5 4.1 0003 0.75 3.4
0004 2.2 5.4 0004 1.5 4.8
0005 3.0 6.9 0005 2.2 5.5
0007 3.7 8.8 0007 3.0 7.2
0011 5.5 11.1 0011 3.7 9.2
0018 7.5 17.5 0018 5.5 14.8
0023 11 23 0023 7.5 18
0031 15 31 0031 11 24
0038 18.5 38 0038 15 31

* Drives with these specifications do not guarantee complete protection for the specified
environmental condition.
Note: Refer to Component Names on page 30 for differences regarding enclosure protection types and
component descriptions.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 27
1.3 Drive Models and Enclosure Types

1.3 Drive Models and Enclosure Types

The following table describes drive enclosures and models.
Table 1.1 Drive Models and Enclosure Types

Enclosure Type
Voltage Class IP20/Open-Chassis IP20/ NEMA Type1)
CIMR-V CIMR-V
BA0001B BA0001F
BA0002B BA0002F
Single-Phase BA0003B BA0003F
200 V Class BA0006B BA0006F
BA0010B BA0010F
BA0012B BA0012F
2A0001B 2A0001F
2A0002B 2A0002F
2A0004B 2A0004F
2A0006B 2A0006F
2A0010B 2A0010F
2A0012B 2A0012F
Three-Phase
2A0020B 2A0020F
200 V Class
2A0030B 2A0030F
2A0040B 2A0040F
2A0056B 2A0056F
2A0069B 2A0069F
4A0001B 4A0001F
4A0002B 4A0002F
4A0004B 4A0004F
4A0005B 4A0005F
4A0007B 4A0007F
Three-Phase
4A0009B 4A0009F
200 V Class
4A0011B 4A0011F
4A0018B 4A0018F
4A0023B 4A0023F
4A0031B 4A0031F
4A0038B 4A0038F

28 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 1.3 Drive Models and Enclosure Types

• Two types of enclosures are offered for V1000 drives.

TERMS • IP20/Open-Chassis models are often placed inside a large enclosure panel where the front of the
drive is covered to prevent someone from accidentally touching charged components.
• IP20/NEMA Type 1 models mount to an indoor wall and not inside a large enclosure panel.

Receiving
1

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 29
1.4 Component Names

1.4 Component Names

This section illustrates the drive components as they are mentioned in this manual.
Note: For a detailed description of digital operator functions, refer to XREF digital operator. The
digital LED operator is not removable.
Note: The number of drive cooling fans varies depending on drive model.

◆ IP20/Open-Chassis
■ Single-phase AC200 V CIMR-V BA0001B ~ 00003B
Three-phase AC200 V CIMR-V 2A0001B ~ 0006B
Figure 1.2

A
L
B
K

J
C
I
H

E
G F

A – Fan cover G – Front cover screw

B – Mounting hole H – Front cover
C – Heatsink I – Comm port
Refer to Network Communications
on page 405
D – Optional 24 V DC power supply J – LED operator
connector cover Refer to Using the Digital LED
Operator on page 91
E – Terminal board K – Drive case
Refer to Table 3.6 on page 70
F – Terminal cover L – Cooling fan
Refer to Drive Cooling Fans on
page 254

Figure 1.2 Exploded View of IP20/Open-Chassis Type Components

Three-Phase AC200 V CIMR-V 2A0006B

30 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 1.4 Component Names

■ Single-Phase AC200 V CIMR-V BA0006B ~ 0012B

Three-Phase AC200 V CIMR-V 2A0010B ~ 0020B
Three-Phase AC400 V CIMR-V 4A0001B ~ 0011B
Figure 1.3

Receiving
A

B 1
L
K
C
J
I
H
D
E

F
G
A – Fan cover H –
Front cover
B – Mounting hole I –
Terminal cover
C – Heatsink J –
Bottom cover
D – Optional 24 V DC power supply K –
LED operator
connector cover Refer to Using the Digital LED
Operator on page 91
E – Comm port L – Case
Refer to Network Communications
on page 405
F – Terminal board M – Cooling fan
Refer to Table 3.6 on page 70 Refer to Drive Cooling Fans on
page 254
G – Front cover screw

Figure 1.3 Exploded view of IP20/Open-Chassis Type Components

Three-Phase AC200 V CIMR-V 2A0012B

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 31
1.4 Component Names

◆ IP20/NEMA Type 1 Enclosure

■ Single-phase AC200 V CIMR-V BA0001F ~ 0003F
Three-phase AC200 V CIMR-V 2A0001F ~ 0006F
Figure 1.4

A
O
B
N
M
L
C
K

J
D
E
F
I G

A – Fan cover I – Front cover screws

B – Mounting hole J – Front cover
C – Heatsink K – Comm port
Refer to Network Communications
on page 405
D – Optional 24 V DC power supply L – LED operator
connector cover Refer to Using the Digital LED
Operator on page 91
E – Terminal board M – Case
Refer to Table 3.6 on page 70
F – Bottom cover screws N – Top cover
G – Rubber bushing O – Cooling fan
Refer to Drive Cooling Fans on
page 254
H – Bottom front cover

Figure 1.4 Exploded View of IP20/NEMA Type 1 Components

Three-phase AC200 V CIMR-V 2A00062F

32 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 1.4 Component Names

■ Single-phase AC200 V CIMR-V BA0006F ~ 0012F

Three-phase AC200 V CIMR-V 2A0010F ~ 0020F
Three-phase AC400 V CIMR-V 4A0001F ~ 0011F
Figure 1.5

Receiving
P

N O B
M 1
L C
K
J
D
E
F

I G
H
A – Fan cover I – Front cover screws
B – Mounting hole J – Front cover
C – Heatsink K – Terminal cover
D – Cable cover L – Comm port
Refer to Network Communications
on page 405
E – Terminal board M – LED operator
Refer to Table 3.6 on page 70 Refer to Using the Digital LED
Operator on page 91
F – Cover screws N – Case
G – Rubber bushing O – Top cover
H – Bottom cover P – Cooling fan
Refer to Drive Cooling Fans on
page 254

Figure 1.5 Exploded view of IP20/NEMA Type 1 Components

Three-phase AC200 V CIMR-V 2A0012F

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 33
1.4 Component Names

■ Three-phase AC200 V CIMR-V 2A0030F ~ 0069F

Three-phase AC400 V CIMR-V 4A00018F ~ 0038F
Figure 1.6

L
K C

J D
I
E
H
G

A – Fan cover G – Front cover

B – Cooling fan H – Terminal board
Refer to Drive Cooling Fans on Refer to Table 3.6 on page 70
page 254
C – Mounting Hole I – Terminal cover
D – Heatsink J – Comm port
Refer to Network Communications
on page 405
E – Cable cover K – LED operator
Refer to Using the Digital LED
Operator on page 91
F – Front cover screws L – Case

Figure 1.6 Exploded view of IP20/NEMA Type 1 Components

Three-phase AC400 V CIMR-V 4A0018F

34 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 1.4 Component Names

◆ Front Views
Figure 1.7

CIMR-V 2A0006B CIMR-V 2A0012B

Receiving
A
I
I A B
H 1
H B
C
C
D D
G G
E
E
F
F
A – Terminal board connector F – Ground terminal
B – DIP switch S1 G – Terminal cover
Refer to Terminal A2 Switch on
page 79
C – DIP switch S3 H – Option card connector
Refer to Sinking/Sourcing Mode Refer to Connecting the Option
Switch on page 77 Card on page 287
D – Control circuit terminal I – DIP switch S2
Refer to Control Circuit Wiring on Refer to MEMOBUS/Modbus
page 69 Termination on page 81
E – Main circuit terminal
Refer to Wiring the Main Circuit Terminal on page 68

Figure 1.7 Front Views of Drives

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 35
1.4 Component Names

36 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 2
Mechanical
Installation
This chapter explains how to properly mount and install the
drive.

2.1 SECTION SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

2.2 MECHANICAL INSTALLATION. . . . . . . . . . . . . . . . . . . . . 41

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 37
2.1 Section Safety

2.1 Section Safety

WARNING
Fire Hazard
Provide sufficient cooling when installing the drive inside an enclosed
panel or cabinet.
Failure to comply could result in overheating and fire.
When multiple drives are placed inside the same enclosure panel, install
proper cooling to ensure air entering the enclosure does not exceed 40 °C.

CAUTION
Crush Hazard
Do not carry the drive by the front cover.
Failure to comply may result in minor or moderate injury from the main
body of the drive falling.

NOTICE
Observe proper electrostatic discharge (ESD) procedures when
handling the drive.
Failure to comply could result in ESD damage to the drive circuitry.

It may be difficult to perform maintenance on the cooling fans of

drives installed in a vertical row inside an enclosure.
Ensure adequate spacing at the top of the drive to perform cooling fan
replacement when required.

38 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 2.1 Section Safety

NOTICE
Operating the drive in the low-speed range diminishes the cooling

Mechanical Installation
effects, increases motor temperature, and may lead to motor damage
by overheating.
Reduce the motor torque in the low-speed range whenever using a non-
Yaskawa motor. If 100% torque is required continuously at low speed,
consider using a special drive or vector motor. Select a motor that is
compatible with the required load torque and operating speed range.

Do not operate motors above the maximum rated RPM. 2

Failure to comply may lead to bearing or other mechanical motor failures.

The speed range for continuous operation differs according to the

lubrication method and motor manufacturer.
If the motor is to be operated at a speed higher than 60 Hz, consult with the
manufacturer.
Continuously operating an oil-lubricated motor in the low-speed range may
result in burning.

When the input voltage is 480 V or higher or the wiring distance is

greater than 100 meters, pay special attention to the motor insulation
voltage or use a drive-rated motor.
Failure to comply could lead to motor winding failure.

Motor vibration may increase when operating a machine in variable-

speed mode, if that machine previously operated at a constant speed.
Install vibration-proof rubber on the motor base or use the frequency jump
function to skip a frequency resonating the machine.

The motor may require more acceleration torque with drive operation
than with a commercial power supply.
Set a proper V/f pattern by checking the load torque characteristics of the
machine to be used with the motor.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 39
2.1 Section Safety

NOTICE
The rated input current of submersible motors is higher than the rated
input current of standard motors.
Select an appropriate drive according to its rated output current. When the
distance between the motor and drive is long, use a cable thick enough to
connect the motor to the drive to prevent motor torque reduction.

When an using an explosion-proof motor, it must be subject to an

explosion-proof test in conjunction with the drive.
This is also applicable when an existing explosion-proof motor is to be
operated with the drive. Since the drive itself is not explosion-proof,
always install it in a safe place.

Do not use a drive for a single phase motor.

Replace the motor with a three phase motor.

If an oil-lubricated gearbox or speed reducer is used in the power

transmission mechanism, oil lubrication will be affected when the
motor operates only in the low speed range.
The power transmission mechanism will make noise and experience
problems with service life and durability if the motor is operated at a speed
higher than 60 Hz.

40 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 2.2 Mechanical Installation

2.2 Mechanical Installation

This section outlines specifications, procedures, and environment for proper mechanical

Mechanical Installation
installation of the drive.

◆ Installation Environment
To help prolong the optimum performance life of the drive, install the drive in the proper
environment. The table below provides description of the appropriate environment for the
drive.
Table 2.1 Installation Environment
2
Environment Conditions
Installation Area Indoors
-10 C to +40 C (IP20/NEMA Type 1)
-10 C to +50 C (IP20/Open-Chassis)
Ambient Drive reliability improves in enviroments without wide temperature fluctuations.
Temperature When using an enclosure panel, install a cooling fan or air conditioner in the area to ensure
that the air temperature inside the enclosure does not exceed the specified levels.
Do not allow ice to develop on the drive.
Humidity 95% RH or less and free of condensation
Storage Temperature -20 C to +60 C
• Install the drive in an area free from:
• oil mist and dust
• metal shavings, oil, water or other foreign materials
• radioactive materials
Surrounding Area • combustible materials (e.g., wood)
• harmful gases and liquids
• excessive vibration
• chlorides
• direct sunlight.
Altitude 1000 m or lower
10 to 20 Hz at 9.8 m/s2
Vibration
20 to 55 Hz at 5.9 m/s2
Orientation Install the drive vertically to maintain maximum cooling effects.

NOTICE: Prevent foreign matter such as metal shavings or wire clippings from falling into the drive during
installation and project construction. Failure to comply could result in damage to the drive. Place a
temporary cover over the top of the drive during installation. Remove the temporary cover before start-up, as
the cover will reduce ventilation and cause the drive to overheat.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 41
2.2 Mechanical Installation

◆ Installation Orientation and Spacing

Install the drive upright as illustrated in Figure 2.1 to maintain proper cooling.
Figure 2.1

A B B

A – Correct B – Incorrect

Figure 2.1 Correct Installation Orientation

■ Single Drive Installation

To maintain sufficient space for airflow and wiring, refer to Figure 2.2. Install the heatsink
against a closed surface to avoid diverting cooling air around the heatsink.
Figure 2.2

Side Clearance Top/Bottom Clearance

A A
C

A – 30 mm minimum C – 100 mm minimum

B – Airflow direction D –

Figure 2.2 Correct Installation Spacing

Note: IP20/NEMA Type 1 and IP20/Open-Chassis models require the same amount of space above
and below the drive for installation.

42 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 2.2 Mechanical Installation

■ Multiple Drive Installation

When installing multiple drives into the same enclosure panel, mount the drives according to
Figure 2.2. When mounting drives with a minimum side-by-side clearance of 2 mm

Mechanical Installation
according to Figure 2.3, derating must be considered and parameter L8-35 must be set.
Refer to Parameter List on page 309.
Figure 2.3

A B 2 mm B
C

2
D

A – Line up the tops of the drives. C – 100 mm minimum

B – 30 mm minimum D – Airflow direction

Figure 2.3 Space Between Drives (Side-by-Side Mounting)

Note: When installing drives of different sizes into the same enclosure panel, the tops of the drives
should line up. Leave space between the top and bottom of stacked drives for cooling fan
replacement if required. Using this method, it is possible to replace the cooling fans later.

NOTICE: When drives with IP20/NEMA Type 1 enclosures are mounted side-by-side, the top covers of all
drives must be removed as shown in the figure below.
Figure 2.4

Figure 2.4 IP20/NEMA 1 Side-by-Side Mounting in Enclosure

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 43
2.2 Mechanical Installation

◆ Removing and Attaching the Protective Covers

Refer to Electrical Installation on page 51, for information regarding the removal and
reattachment of protective covers.

◆ Exterior and Mounting Dimensions

The table below matches each drive model with its appropriate drawing.
Table 2.2 Drive Models and Types

Drive Model CIMR-V

Protective Design Single-Phase Three-Phase Three-Phase Page
200 V Class 200 V Class 400 V Class
2 0001B
B 0001B
2 0002B
B 0002B – 45
2 0004B
B 0003B
2 0006B
4 0001B
4 0002B
B 0006B 2 0010B 4 0004B
IP20/Open-Chassis B 0010B 2 0012B 4 0005B 46
B 0012B 2 0020B 4 0007B
4 0009B
4 0011B
2 0030B 4 0018B
2 0040B 4 0023B
– 49
2 0056B 4 0031B
2 0069B 4 0038B
2 0001F
B 0001F
2 0002F
B 0002F – 47
2 0004F
B 0003F
2 0006F
4 0001F
4 0002F
B 0006F 2 0010F 4 0004F
IP20/NEMA Type 1 B 0010F 2 0012F 4 0005F 48
B 0012F 2 0020F 4 0007F
4 0009F
4 0011F
2 0030F 4 0018F
2 0040F 4 0023F
– 49
2 0056F 4 0031F
2 0069F 4 0038F

Note: For information on the amount of heat generated by the drive and appropriate cooling methods,
refer to Specifications on page 291.

44 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 2.2 Mechanical Installation

■ IP20/Open-Chassis Drives
Table 2.3 IP20/Open-Chassis (without an EMC filter)

Mechanical Installation
W1 2-M4 t1

H1
H
2

D1
H2

W
D

Dimensions (in)
Drive Model
Voltage Class CIMR-V Weight
W1 H1 W H D t1 H2 D1
(lb)
BA0001B 2.20 4.65 2.68 5.04 2.99 0.12 0.20 0.26 1.3
Single-Phase
BA0002B 2.20 4.65 2.68 5.04 2.99 0.12 0.20 0.26 1.3
200 V Class
BA0003B 2.20 4.65 2.68 5.04 4.65 0.20 0.20 1.52 2.2
2A0001B 3.78 4.65 4.25 5.04 5.08 0.12 0.20 2.28 1.3
Three-Phase 2A0002B 3.78 4.65 4.25 5.04 5.41 0.12 0.20 2.28 1.3
200 V Class 2A0004B 5.04 4.65 5.51 5.04 5.63 0.12 0.20 2.56 2.0
2A0006B 3.78 4.65 4.25 5.04 5.08 0.12 0.20 2.28 2.4

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 45
2.2 Mechanical Installation

Table 2.4 IP20/Open-Chassis (without an EMC filter)

W1 4-M4

H1
H

t1
D1
H2

W
D

Dimensions (in)
Drive Model
Voltage Class CIMR-V Weight
W1 H1 W H D t1 H2 D1 (lb)
BA0006B 3.78 4.65 4.25 5.04 5.41 0.20 0.20 2.28 3.7
Single-Phase
BA0010B 3.78 4.65 4.25 5.04 6.06 0.20 0.20 2.28 4.0
200 V Class
BA0012B 5.04 4.65 5.51 5.04 6.42 0.20 0.20 2.56 5.3
2A0010B 3.78 4.65 4.25 5.04 5.08 0.20 0.20 2.28 3.7
Three-Phase
2A0012B 3.78 4.65 4.25 5.04 5.41 0.20 0.20 2.28 3.7
200 V Class
2A0020B 5.04 4.65 5.51 5.04 5.63 0.20 0.20 2.56 5.3
4A0001B 3.78 4.65 4.25 5.04 3.19 0.20 0.20 0.39 2.2
4A0002B 3.78 4.65 4.25 5.04 3.90 0.20 0.20 1.10 2.6
4A0004B 3.78 4.65 4.25 5.04 5.41 0.20 0.20 2.28 3.7
Three-Phase
4A0005B 3.78 4.65 4.25 5.04 6.06 0.20 0.20 2.28 3.7
400 V Class
4A0007B 3.78 4.65 4.25 5.04 6.06 0.20 0.20 2.28 3.7
4A0009B 3.78 4.65 4.25 5.04 6.06 0.20 0.20 2.28 3.7
4A0011B 5.04 4.65 5.51 5.04 5.63 0.20 0.20 2.56 5.3

46 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 2.2 Mechanical Installation

■ IP20/NEMA Type 1 Drives

Table 2.5 IP20/NEMA Type 1 (without an EMC filter)

Mechanical Installation
W1 2-M4 t1

H6
H2
H1
H
H4
H5
2

D1
W D
H3

Dimensions (in)
Drive Model
Voltage Class CIMR-V Weight
W1 H2 W H1 D t1 H5 D1 H H4 H3 H6 (lb)
BA0001F 2.20 4.65 2.68 5.10 2.99 0.12 0.20 0.26 5.89 0.79 0.16 0.06 1.5
Single-Phase
BA0002F 2.20 4.65 2.68 5.10 2.99 0.12 0.20 0.26 5.89 0.79 0.16 0.06 1.8
200 V Class
BA0003F 2.20 4.65 2.68 5.10 4.65 0.20 0.20 1.54 5.89 0.79 0.16 0.06 2.4
2A0001F 2.20 4.65 2.68 5.10 2.99 0.12 0.20 0.26 5.89 0.79 0.16 0.06 3.8
Three-Phase 2A0002F 2.20 4.65 2.68 5.10 2.99 0.12 0.20 0.26 5.89 0.79 0.16 0.06 3.8
200 V Class 2A0004F 2.20 4.65 2.68 5.10 4.25 0.20 0.20 1.54 5.89 0.79 0.16 0.06 2.2
2A0006F 2.20 4.65 2.68 5.10 5.04 0.20 0.20 2.32 5.89 0.79 0.16 0.06 3.7

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 47
2.2 Mechanical Installation

Table 2.6 IP20/NEMA Type 1 (without an EMC filter)

W1 4-M4 t1

H6
H2
H1
H
H5
H4

D1
D
H3

Dimensions (in)
Drive Model
Voltage Class CIMR-V Weight
W1 H2 W H1 D t1 H5 D1 H H4 H3 H6 (lb)
BA0006F 3.78 4.65 4.25 5.10 5.41 0.20 0.20 2.28 5.89 0.79 0.16 0.06 3.8
Single-Phase
BA0010F 3.78 4.65 4.25 5.10 6.06 0.20 0.20 2.28 5.89 0.79 0.16 0.06 3.8
200 V Class
BA0012F 5.04 4.65 5.51 5.24 6.42 0.20 0.20 2.56 6.02 0.79 0.19 0.20 5.3
2A0010F 3.78 4.65 4.25 5.10 5.08 0.20 0.20 2.28 5.89 0.79 0.16 0.06 3.3
Three-Phase
2A0012F 3.78 4.65 4.25 5.10 5.41 0.20 0.20 2.28 5.89 0.79 0.16 0.06 3.5
200 V Class
2A0020F 5.04 4.65 5.51 5.24 5.63 0.20 0.20 2.56 6.02 0.79 0.19 0.20 5.3
4A0001F 3.78 4.65 4.25 5.10 3.19 0.20 0.20 0.39 5.89 0.79 0.16 0.06 2.2
4A0002F 3.78 4.65 4.25 5.10 3.90 0.20 0.20 1.10 5.89 0.79 0.16 0.06 2.7
4A0004F 3.78 4.65 4.25 5.10 5.41 0.20 0.20 2.28 5.89 0.79 0.16 0.06 3.5
Three-Phase
4A0005F 3.78 4.65 4.25 5.10 6.06 0.20 0.20 2.28 5.89 0.79 0.16 0.06 3.8
400 V Class
4A0007F 3.78 4.65 4.25 5.10 6.06 0.20 0.20 2.28 5.89 0.79 0.16 0.06 3.8
4A0009F 3.78 4.65 4.25 5.10 6.06 0.20 0.20 2.28 5.89 0.79 0.16 0.06 3.8
4A0011F 5.04 4.65 5.51 5.24 5.63 0.20 0.20 2.56 6.02 0.79 0.19 0.20 5.3

48 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 2.2 Mechanical Installation

Table 2.7 IP20/NEMA Type 1 (without an EMC filter)

W1 4-d

Mechanical Installation
H6
H2
H1
H
2

t1
H4
H5

W D1
H3

Dimensions (in)
Drive Model
Voltage Class CIMR-V Weight
W1 H2 W H1 D t1 H5 D1 H H4 H3 H6 d (lb)
2A0030B 4.80 9.76 5.51 9.76 5.51 0.20 0.51 2.17 10.00 0.51 0.24 0.06 4.80 8.38
Three-Phase 2A0040B 4.80 9.76 5.51 9.76 5.51 0.20 0.51 2.17 10.00 0.51 0.24 0.06 4.80 8.38
200 V Class 2A0056B 6.30 11.18 7.09 11.18 6.42 0.20 0.51 2.95 11.42 0.59 0.24 0.06 6.30 12.13
2A0069B 7.56 13.23 8.66 13.23 7.36 0.20 0.87 3.07 13.78 0.59 0.28 0.06 7.56 20.28
4A0018B 4.80 9.76 5.51 9.76 5.51 0.20 0.51 2.17 10.00 0.51 0.24 0.06 4.80 8.38
Three-Phase 4A0023B 4.80 9.76 5.51 9.76 5.51 0.20 0.51 2.17 10.00 0.51 0.24 0.06 4.80 8.38
400 V Class 4A0031B 6.30 11.18 7.09 11.18 5.63 0.20 0.51 2.17 11.42 0.59 0.24 0.06 6.30 11.46
4A0038B 6.30 11.18 7.09 11.18 6.42 0.20 0.51 2.95 11.42 0.51 0.24 0.06 6.30 12.13

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 49
2.2 Mechanical Installation

50 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 3
Electrical
Installation
This chapter explains proper procedures for wiring the control
circuit terminals, motor and power supply.

3.1 SECTION SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

3.2 STANDARD CONNECTION DIAGRAM. . . . . . . . . . . . . . . 55
3.3 MAIN CIRCUIT CONNECTION DIAGRAM . . . . . . . . . . . . 58
3.4 TERMINAL BLOCK CONFIGURATION. . . . . . . . . . . . . . . 59
3.5 PROTECTIVE COVERS . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
3.6 MAIN CIRCUIT WIRING . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
3.6 MAIN CIRCUIT WIRING . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
3.8 I/O CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
3.9 MAIN FREQUENCY REFERENCE . . . . . . . . . . . . . . . . . . 79
3.10 MEMOBUS/MODBUS TERMINATION. . . . . . . . . . . . . . . 81
3.11 BRAKING RESISTOR . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 51
3.1 Section Safety

3.1 Section Safety

DANGER
Electrical Shock Hazard
Do not connect or disconnect wiring while the power is on.
Failure to comply will result in death or serious injury.

WARNING
Electrical Shock Hazard
Do not operate equipment with covers removed.
Failure to comply could result in death or serious injury.
The diagrams in this section may show drives without covers or safety
shields to show details. Be sure to reinstall covers or shields before
operating the drives and run the drives according to the instructions
described in this manual.

Always ground the motor-side grounding terminal.

Improper equipment grounding could result in death or serious injury by
contacting the motor case.

Do not perform work on the drive while wearing loose clothing,

jewelry or without eye protection.
Failure to comply could result in death or serious injury.
Remove all metal objects such as watches and rings, secure loose clothing,
and wear eye protection before beginning work on the drive.

Do not remove covers or touch circuit boards while the power is on.
Failure to comply could result in death or serious injury.

52 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 3.1 Section Safety

WARNING
Do not allow unqualified personnel to perform work on the drive.
Failure to comply could result in death or serious injury.
Installation, maintenance, inspection, and servicing must be performed

Electrical Installation
only by authorized personnel familiar with installation, adjustment, and
maintenance of AC drives.

Do not touch any terminals before the capacitors have fully

discharged.
Failure to comply could result in death or serious injury.
Before wiring terminals, disconnect all power to the equipment. The 3
internal capacitor remains charged even after the power supply is turned
off. The charge indicator LED will extinguish when the DC bus voltage is
below 50 Vdc. To prevent electric shock, wait at least five minutes after all
indicators are off and measure the DC bus voltage level to confirm safe
level.

Fire Hazard
Tighten all terminal screws to the specified tightening torque.
Loose electrical connections could result in death or serious injury by fire
due to overheating of electrical connections.

Do not use improper combustible materials.

Failure to comply could result in death or serious injury by fire.
Attach the drive to metal or other noncombustible material.

Do not use an improper voltage source.

Failure to comply could result in death or serious injury by fire.
Verify that the rated voltage of the drive matches the voltage of the
incoming power supply before applying power.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 53
3.1 Section Safety

NOTICE
Observe proper electrostatic discharge procedures (ESD) when
handling the drive and circuit boards.
Failure to comply may result in ESD damage to the drive circuitry.

Never connect or disconnect the motor from the drive while the drive
is outputting voltage.
Improper equipment sequencing could result in damage to the drive.

Do not use unshielded cable for control wiring.

Failure to comply may cause electrical interference resulting in poor
system performance. Use shielded, twisted-pair wires and ground the
shield to the ground terminal of the drive.

Check all the wiring to ensure that all connections are correct after
installing the drive and connecting any other devices.
Failure to comply could result in damage to the drive

Do not modify the drive circuitry.

Failure to comply could result in damage to the drive and will void
warranty.
Yaskawa is not responsible for any modification of the product made by the
user. This product must not be modified.

54 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 3.2 Standard Connection Diagram

3.2 Standard Connection Diagram

Connect the drive and peripheral devices as shown in Figure 3.1. It is possible to run the
drive via the digital operator without connecting digital I/O wiring. This section does not
discuss drive operation; Refer to Start-Up Programming & Operation on page 87 for
instructions on operating the drive.

Electrical Installation
NOTICE: Inadequate branch short circuit protection could result in damage to the drive. Install adequate
branch circuit short circuit protection per applicable codes. The drive is suitable for circuits capable of
delivering not more than 18,000 RMS symmetrical amperes, 240 Vac maximum (200 V Class) and 480 Vac
maximum (400 V Class).

NOTICE: When the input voltage is 480 V or higher or the wiring distance is greater than 100 meters, pay
special attention to the motor insulation voltage or use an inverter duty motor. Failure to comply could lead
to motor insulation breakdown.

NOTICE: Do not connect the AC control circuit ground to the drive enclosure. Improper drive grounding can
cause the control circuit to malfunction. 3
NOTICE: The minimum load for the multi-function relay output MA-MB-MC is 10 mA. If a circuit requires less
than 10 mA, connect it to a photocoupler output (P1, P2, PC). Improper application of peripheral devices
could result in damage to the photocoupler output of the drive.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 55
3.2 Standard Connection Diagram

Figure 3.1

_
Terminals +1, +2, , B1, and B2
are for connecting options.
DC reactor
(option) *1 *2
Thermal relay
Never connect power supply
lines to these terminals. (option) Braking resistor Motor
2 MCCB
*3 Jumper (option)
Cooling fan
For single phase 200 V r1 FU
r1
power supply, use
+2 +1 - B1 B2 FV
R/L1 and S/L2. s1 s1 M
FW
1 MCCB MC
t1
V1000 t1

Three phase R/L1 R/L1 U

power supply S/L2 U/T1
S/L2 Main circuit V
200 to 240 V V/T2 M
T/L3 T/L3 W
Control circuit W/T3
*4
Forward run/stop S1
2 MCCB THRX OFF ON MC
Ground
SA Reverse run/stop S2 10 Ω or less (400 V class)
MC Option card 100 Ω or less (200 V class)
THRX External fault S3 connector

Thermal relay for SA Fault reset S4 DIP switch S1 Digital output

motor cooling fan Multi-step V I 250 Vac, 10 mA to 1 A
TRX speed 1 30 Vdc, 10 mA to 1 A
main/aux switch S5 (default setting)
MC SA Multi-step
TRX speed 2 S6
MC MA
Fault relay Jog reference MA Fault
S7
Digital inputs +24 V 8 mA MB Digital output
(default setting) 24 V 5 ~ 48 Vdc
2 to 50 mA
*5 Sink MC (default setting)
DIP
switch S3 Source
SC
P1 During Run
Shield ground 0V (photocoupler 1)
terminal

P2 Frequency agree
(photocoupler 2)
Pulse train input
RP
(max. 32 kHz) PC Photocoupler
Setting power supply output common
+V
2 kΩ +10.5 max. 20 mA
MP
*6
Pulse train output
Main speed A1 0 to +10 V (20 kΩ) 0 to 32 kHz
frequency A2 0 to +10 V (20 kΩ) Analog monitor
AM
reference. (0)4 to 20 mA (250 Ω) + output
Multi-function AM
AC 0 to +10 Vdc
programmable AC - (2 mA)

Termination Comm.
DIP Monitor
resistor connector
switch output
Safety switch 120 Ω, 1/2 W
S2 R+
Safe Disable HC
*7
Input R-
Jumper
H1 S+ MEMOBUS/
S- Modbus comm.
RS-485/422
IG

Cable shield ground

shielded line twisted-pair shielded line

main circuit terminal control terminal

Figure 3.1 Drive Standard Connection Diagram

56 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 3.2 Standard Connection Diagram

* 1. Remove the jumper when installing an optional DC reactor.

* 2. The MC on the input side of the main circuit should open when the thermal relay is triggered.
* 3. Self-cooled motors do not require separate cooling fan motor wiring.
* 4. Connected using sequence input signal (S1 to S7) from NPN transistor; Default: sink mode ( 0 V com)
* 5. Use only a +24 V internal power supply in sinking mode; the source mode requires an external power
supply. Refer to I/O Connections on page 77.
* 6. Monitor outputs work with devices such as analog frequency meters, ammeters, voltmeters and
wattmeters; they are intended for use as a feedback-type of signal.

Electrical Installation
* 7. Disconnect the wire jumper between HC and H1 when utilizing the safety input.

WARNING! Sudden Movement Hazard. Do not close the wiring for the control circuit unless the
multifunction input terminal parameter is properly set (S5 for 3-wire; H1-05 = “0”). Improper sequencing of
run/stop circuitry could result in death or serious injury from moving equipment.

WARNING! Sudden Movement Hazard. Ensure start/stop and safety circuits are wired properly and in the
correct state before energizing the drive. Failure to comply could result in death or serious injury from
moving equipment. When programmed for 3-wire control, a momentary closure on terminal S1 may cause
the drive to start.

WARNING! When 3-Wire sequence is used, set the drive to 3-Wire sequence before wiring the control 3
terminals and ensure parameter b1-17 is set to 0 (drive does not accept a run command at power up
(default)). If the drive is wired for 3-Wire sequence but set up for 2-Wire sequence (default) and if parameter
b1-17 is set to 1 (drive accepts a Run command at power up), the motor will rotate in reverse direction at
power up of the drive and may cause injury.

WARNING! When the application preset funcion is executed (or A1-06 is set to any value other than 0) the
drive I/O terminal funcitons change. This may cause unexpected operation and potential damage to
equipment or injury.

Figure 3.2 illustrates an example of a 3-wire sequence.

Figure 3.2

Drive
Stop relay (N.C.) Run relay (N.O.)
S1
Run command (run on momentary close)
S2
Stop command (stop on momentary open)
S5 Foward/reverse command
(multi-function input: H1-05 = 0)
SC
Sequence input common

Figure 3.2 3-Wire Sequence

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 57
3.3 Main Circuit Connection Diagram

3.3 Main Circuit Connection Diagram

Refer to Figure 3.3 and Figure 3.4 for standard drive connection diagrams. Connections
may vary based on drive capacity. The main circuit DC power supply powers the control
circuit.
NOTICE: Do not use the negative DC bus terminal “-” as a ground terminal. This terminal is at high voltage
DC potential. Improper wiring connections could result in damage to the drive.

◆ Single-Phase 200 V Class (CIMR-V BA0001 ~ 0012)

Figure 3.3

DC reactor
(option) Braking Resistor
Jumper Unit (option)

㧗2 㧗1 B1 B2

R/L1 Drive
U/T1
V/T2 Motor
S/L2 W/T3
Single-phase
㧙
200 Vac

Figure 3.3 Connecting Main Circuit Terminals

NOTICE: Do not connect T/L3 terminal when using single-phase power supply input. Incorrect wiring may
damage the drive.

◆ Three-Phase 200 V Class (CIMR-V 2A0001 ~ 0069)

Three-Phase 400 V Class (CIMR-V 4A0001 ~ 0038)
Figure 3.4

DC reactor Braking
(option) Resistor Unit
Jumper (option)

㧗2 㧗1 B1 B2
R/L1 Drive U/T1
S/L2 V/T2 Motor
T/L3 W/T3
Three phase 200 Vac
㧙
(400 Vac)

Figure 3.4 Connecting Main Circuit Terminals

58 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 3.4 Terminal Block Configuration

3.4 Terminal Block Configuration

The figures in this section provide quick reference detailed illustrations of the main and
control circuit terminal block configurations.
Figure 3.5

Electrical Installation
Models CIMR-V BA0006, 0010, 0012 Models CIMR-V BA0001,
CIMR-V 2A0010, 0012, 0020, 0040, 0002, 0003
0056, 0069 CIMR-V 2A0001, 0002,
CIMR-V 4A0001, 0002, 0004, 0005, 0004, 0006
0007, 0009, 0011, 0023, 0031, 0038 3

Figure 3.5 Main Circuit Terminal Block Configurations

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 59
3.5 Protective Covers

3.5 Protective Covers

Follow the procedure below to remove the protective covers before wiring the drive and to
reattach the covers after wiring is complete.

◆ IP20/Open-Chassis
■ Removing the Protective Covers

Figure 3.6
1. Loosen the screw that locks the front cover in place to remove.

Figure 3.6 Remove the Front Cover on an IP20/Open-Chassis Drive

2. Apply pressure to the tabs on each side of the terminal cover. Pull the terminal cover
away from the drive while pushing in on the tabs to pull the cover free.
Figure 3.7

Figure 3.7 Remove the Terminal Cover on an IP20/Open-Chassis Drive

■ Reattaching the Protective Covers

Properly connect all wiring and route power wiring away from control signal wiring.
Reattach all protective covers when wiring is complete. Apply only a small amount of
pressure to lock the cover back into place.

60 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 3.5 Protective Covers

Figure 3.8

Electrical Installation
Figure 3.8 Reattach the Protective Covers on an IP20/Open-Chassis Drive

◆ IP20/NEMA Type 1
■ Removing the Protective Covers on an IP20/NEMA Type 1 design
3
Figure 3.9
1. Loosen the screw on the front cover to remove the front cover.

Figure 3.9 Remove the Front Cover on an IP20/NEMA Type 1 Drive

2. Loosen the screw on the terminal cover (Figure 3.10, B) to remove the terminal
Figure 3.10
cover and expose the conduit bracket (Figure 3.10, A).

A
B
Figure 3.10 Remove the Terminal Cover on an IP20/NEMA Type 1 Drive

3. Loosen two screws attaching the conduit bracket (Figure 3.11, A) to remove.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 61
3.5 Protective Covers

Figure 3.11

A
Figure 3.11 Remove the Conduit Bracket on an IP20/Open-Chassis Drive

■ Reattaching the Protective Covers

Pass power wiring and control signal wiring through the exit holes on the bottom of the
conduit bracket of the drive. Place power wiring and control signal wiring in separate
conduits. Properly connect all wiring after installing the drive and connecting other devices.
Reattach all protective covers when wiring is complete.
Figure 3.12

A – Pass power wiring and control signal wiring through different

exit holes at the bottom of the drive.

Figure 3.12 Reattach the Protective Covers and

Conduit Bracket on an IP20/NEMA Type 1 Drive

62 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 3.6 Main Circuit Wiring

3.6 Main Circuit Wiring

This section describes the functions, specifications, and procedures required to safely and
properly wire the main circuit of the drive.
NOTICE: Do not solder the ends of wire connections to the drive. Soldered wiring connections can loosen
over time. Improper wiring practices could result in drive malfunction due to loose terminal connections.

Electrical Installation
◆ Main Circuit Terminal Functions
Table 3.1 Main Circuit Terminal Functions

Terminal Type Function Reference

R/L1 Connects line power to the drive.
Main circuit power
S/L2 Drives with single phase 200 V input power use terminals R/L1 58
T/L3
supply input
and S/L2 only (T/L3 must not be used). 3
U/T1
V/T2 Drive output Connects to the motor. 67
W/T3
B1 Available for connecting a braking resistor or the braking resistor
Braking resistor 82
B2 unit option.
+1 DC reactor These terminals are shorted at shipment. Remove the shorting bar
274
+2 connection between +1 and +2 when connecting to this terminal.
+1 DC power supply
For connecting a DC power supply. -
– input
Grounding Terminal
Ground For 200 V class: 100 Ω or less 67
(2 terminals) For 400 V class: 10 Ω or less

◆ Wire Gauges and Tightening Torque

Select the appropriate wires and crimp terminals from Table 3.2 through Table 3.5.
Note: 1. Wire gauge recommendations based on drive continuous current ratings using 75°C 600 Vac vinyl-
sheathed wire assuming ambient temperature within 30°C and wiring distance less than 100 m.
2. Terminals +1, +2, –, B1 and B2 are for connecting optional devices such as a DC reactor or braking
resistor. Do not connect other non-specified devices to these terminals.
• Consider the amount of voltage drop when selecting wire gauges.
Increase the wire gauge when the voltage drop is greater than 2% of motor rated voltage.
Ensure the wire gauge is suitable for the terminal block. Use the following formula to
calculate the amount of voltage drop:
• Line drop voltage (V) = 3 x wire resistance (Ω/km) x wire length (m) x current (A) x10-3

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 63
3.6 Main Circuit Wiring

• Refer to instruction manual TOBPC72060000 for braking unit or braking resistor unit
wire gauges.
• Refer to Standards Compliance on page 413 for information on UL compliance.
■ Single-Phase 200 V Class
Table 3.2 Wire Gauge and Torque Specifications

Model Screw Tightening Applicable Recommended Line

CIMR- Terminal Size Torque Gauge Gauge Type
V BA N•m (lb.in.) mm2 (AWG) mm2 (AWG)
0001 R/L1, S/L2, U/T1, V/T2, W/ 0.8 to 1.0 0.75 to 2.0 2
0002 M3.5 Note: 1.
T3, –, +1, +2, B1, B2, (7.1 to 8.9) (18 to 14) (14)
0003
R/L1, S/L2, U/T1, V/T2, W/ 1.2 to 1.5 2.0 to 5.5 2
0006 M4 Note: 1.
T3, –, +1, +2, B1, B2, (10.6 to 13.3) (14 to 10) (14)
R/L1, S/L2, U/T1, V/T2, W/ 1.2 to 1.5 2.0 to 5.5 3.5
M4 Note: 1.
T3, (10.6 to 13.3) (14 to 10) (12)
0010
1.2 to 1.5 2.0 to 5.5 5.5
–, +1, +2, B1, B2, M4 Note: 1.
(10.6 to 13.3) (14 to 10) (10)
R/L1, S/L2, U/T1, V/T2, W/ 1.2 to 1.5 2.0 to 5.5 5.5
0012 M4 Note: 1.
T3, –, +1, +2, B1, B2, (10.6 to 13.3) (14 to 10) (10)

■ Three-Phase 200 V Class

Table 3.3 Wire Gauge and Torque Specifications

Model Tightening Applicable Recommended

Screw Line
CIMR- Terminal Torque Gauge Gauge
Size Type
V 2A N•m (lb.in.) mm2 (AWG) mm2 (AWG)
0001
0002 R/L1, S/L2, T/L3, U/T1, V/T2, 0.8 to 1.0 0.75 to 2.0 2
M3.5 Note: 1.
0004 W/T3, –, +1, +2, B1, B2, (7.1 to 8.9) (18 to 14) (14)
0006
R/L1, S/L2, T/L3, U/T1, V/T2, 1.2 to 1.5 2.0 to 5.5 2
M4 Note: 1.
W/T3, –, +1, +2, B1, B2 (10.6 to 13.3) (14 to 10) (14)
0010
1.2 to 1.5 2.0 to 5.5 3.5
M4 Note: 1.
(10.6 to 13.3) (14 to 10) (12)
R/L1, S/L2, T/L3, U/T1, V/T2, 1.2 to 1.5 2.0 to 5.5 3.5
0012 M4 Note: 1.
W/T3, –, +1, +2, B1, B2, (10.6 to 13.3) (14 to 10) (12)
R/L1, S/L2, T/L3, U/T1, V/T2, 1.2 to 1.5 2.0 to 5.5 5.5
0020 M4 Note: 1.
W/T3, –, +1, +2, B1, B2, (10.6 to 13.3) (14 to 10) (10)

64 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 3.6 Main Circuit Wiring

Model Screw Tightening Applicable Recommended Line

CIMR- Terminal Size Torque Gauge Gauge Type
V 2A N•m (lb.in.) mm2 (AWG) mm2 (AWG)
R/L1,S/L2,T/L3,U/T1,V/ 2 to 2.5 5.5 to 14 8
M5 Note: 1.
T2,W/T3,-,+1,+2 (17.7 to 22.1) (10 to 6) (8)
1.2 to 1.5 2.0 to 5.5 5.5
0030 B1,B2 M4 Note: 1.
(10.6 to 13.3) (14 to 10) (10)

Electrical Installation
2 to 2.5 5.5 to 14 8
M5 Note: 1.
(17.7 to 22.1) (10 to 6) (8)
R/L1,S/L2,T/L3,U/T1,V/ 2 to 2.5 5.5 to 14 14
M5 Note: 1.
T2,W/T3,-,+1,+2 (17.7 to 22.1) (10 to 6) (6)
1.2 to 1.5 2.0 to 5.5 5.5
0040 B1,B2 M4 Note: 1.
(10.6 to 13.3) (14 to 10) (10)
2 to 2.5 5.5 to 14 8
M5 Note: 1.
(17.7 to 22.1) (10 to 6) (8)
R/L1,S/L2,T/L3,U/T1,V/
M6
4 to 6 14 to 22 22
Note: 1.
3
T2,W/T3,-,+1,+2 (35.4 to 53.1) (6 to 4) (4)
2 to 2.5 5.5 to 8 8
0056 B1,B2 M5 Note: 1.
(17.7 to 22.1) (10 to 8) (8)
4 to 6 14 to 22 22
M6 Note: 1.
(35.4 to 53.1) (6 to 4) (4)
R/L1,S/L2,T/L3,U/T1,V/ 9 to 11 8 to 38 38
M8 Note: 1.
T2,W/T3,-,+1,+2 (79.7 to 11.0) (8 to 2) (2)
2 to 2.5 8 to 14 14
0069 B1,B2 M5 Note: 1.
(17.7 to 22.1) (8 to 6) (6)
4 to 6 8 to 22 22
M6 Note: 1.
(35.4 to 53.1) (8 to 4) (4)

■ Three-Phase 400 V Class

Table 3.4 Wire Gauge and Torque Specifications

Model Tightening Applicable Recommended

CIMR- Screw Line
Terminal Torque Gauge Gauge
Size Type
V 4A N•m (lb.in.) mm2 (AWG) mm2 (AWG)
0001
0002 R/L1, S/L2, T/L3, U/T1, V/T2, 1.2 to 1.5 2.0 to 5.5 2
0004 M4 Note: 1.
W/T3, –, +1, +2, B1, B2, (10.6 to 13.3) (14 to 10) (14)
0005
0007
R/L1, S/L2, T/L3, U/T1, V/T2, 1.2 to 1.5 2.0 to 5.5 2
M4 Note: 1.
W/T3, –, +1, +2, B1, B2 (10.6 to 13.3) (14 to 10) (14)
0009
1.2 to 1.5 2.0 to 5.5 3.5
M4 Note: 1.
(10.6 to 13.3) (14 to 10) (12)

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 65
3.6 Main Circuit Wiring

Model Screw Tightening Applicable Recommended Line

CIMR- Terminal Size Torque Gauge Gauge Type
V 4A N•m (lb.in.) mm2 (AWG) mm2 (AWG)
R/L1, S/L2, T/L3, U/T1, V/T2, 1.2 to 1.5 2.0 to 5.5 2
M4 Note: 1.
W/T3, –, +1, +2, B1, B2 (10.6 to 13.3) (14 to 10) (14)
0011
1.2 to 1.5 2.0 to 5.5 3.5
M4 Note: 1.
(10.6 to 13.3) (14 to 10) (12)
R/L1,S/L2,T/L3,U/T1,V/ 1.2 to 1.5 2.0 to 5.5 5.5
M4 Note: 1.
T2,W/T3,-,+1,+2 (10.6 to 13.3) (14 to 10) (10)
1.2 to 1.5 2.0 to 5.5 5.5
0018 B1,B2 M4 Note: 1.
(10.6 to 13.3) (14 to 10) (10)
2 to 2.5 5.5 to 14 5.5
M5 Note: 1.
(17.7 to 22.1) (10 to 6) (10)
R/L1,S/L2,T/L3,U/T1,V/ 2 to 2.5 5.5 to 14 8
M5 Note: 1.
T2,W/T3,-,+1,+2 (17.7 to 22.1) (10 to 6) (8)
1.2 to 1.5 2.0 to 5.5 5.5
0023 B1,B2 M4 Note: 1.
(10.6 to 13.3) (14 to 10) (10)
2 to 2.5 5.5 to 14 5.5
M5 Note: 1.
(17.7 to 22.1) (10 to 6) (10)
R/L1,S/L2,T/L3,U/T1,V/ 2 to 2.5 5.5 to 14 8
M5 Note: 1.
T2,W/T3,-,+1,+2 (17.7 to 22.1) (10 to 6) (8)
2 to 2.5 5.5 to 8 8
0031 B1,B2 M5 Note: 1.
(17.7 to 22.1) (10 to 8) (8)
4 to 6 5.5 to 14 8
M6 Note: 1.
(35.4 to 53.1) (10 to 6) (8)
R/L1,S/L2,T/L3,U/T1,V/ 2 to 2.5 5.5 to 14 14
M5 Note: 1.
T2,W/T3,-,+1,+2 (17.7 to 22.1) (10 to 6) (6)
2 to 2.5 5.5 to 8 8
0038 B1,B2 M5 Note: 1.
(17.7 to 22.1) (10 to 8) (8)
4 to 6 5.5 to 14 8
M6 Note: 1.
(35.4 to 53.1) (10 to 6) (8)

◆ Main Circuit Terminal Power Supply and Motor Wiring

This section outlines the various steps, precautions, and checkpoints for wiring the main
circuit terminals and motor terminals.
NOTICE: When connecting the motor to the drive output terminals U/T1, V/T2, and W/T3, the phase order
for the drive and motor should match. Failure to comply with proper wiring practices may cause the motor to
run in reverse if the phase order is backward.

NOTICE: Do not connect phase-advancing capacitors or LC/RC noise filters to the output circuits. Improper
application of noise filters could result in damage to the drive.

NOTICE: Do not connect the AC power line to the output motor terminals of the drive. Failure to comply
could result in death or serious injury by fire as a result of drive damage from line voltage application to

66 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 3.6 Main Circuit Wiring

output terminals.

■ Cable Length Between Drive and Motor

When the cable length between the drive and the motor is too long (especially at low
frequency output), note that the cable voltage drop may cause reduced motor torque. Drive
output current will increase as the leakage current from the cable increases. An increase in
leakage current may trigger an overcurrent situation and weaken the accuracy of the current

Electrical Installation
detection.
Adjust the drive carrier frequency according to the following table. If the motor wiring
distance exceeds 100 m because of the system configuration, reduce the ground currents.
Refer to Carrier Frequency Selection: C6-02 on page 135.
Refer to Table 3.5 to set the carrier frequency to an appropriate level.
Table 3.5 Cable Length Between Drive and Motor

Cable Length 50 m or less 100 m or less Greater than 100 m 3

Carrier Frequency 15 kHz or less 5 kHz or less 2 kHz or less

Note: When setting carrier frequency, calculate the cable length as the total distance of wiring to all
connected motors when running multiple motors from a single drive.

■ Ground Wiring
Follow the precautions to wire the ground for one drive or a series of drives.
WARNING! Electrical Shock Hazard. Always use a ground wire that complies with technical standards on
electrical equipment and minimize the length of the ground wire. Improper equipment grounding may cause
dangerous electrical potentials on equipment chassis, which could result in death or serious injury.

WARNING! Electrical Shock Hazard. Be sure to ground the drive ground terminal. (200 V Class: Ground to
100 Ω or less, 400 V Class: Ground to 10 Ω or less). Improper equipment grounding could result in death or
serious injury by contacting ungrounded electrical equipment.

NOTICE: Do not share the ground wire with other devices such as welding machines or large-current
electrical equipment. Improper equipment grounding could result in drive or equipment malfunction due to
electrical interference.

NOTICE: When using more than one drive, ground multiple drives according to instructions. Improper
equipment grounding could result in abnormal operation of drive or equipment.

Refer to Figure 3.13 when using multiple drives. Do not loop the ground wire.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 67
3.6 Main Circuit Wiring

Figure 3.13

A A B

A – Correct B – Incorrect

Figure 3.13 Multiple Drive Wiring

■ Wiring the Main Circuit Terminal

WARNING! Electrical Shock Hazard. Shut off the power supply to the drive before wiring the main circuit
terminals. Failure to comply may result in death or serious injury.

Note: 1. A cover placed over the DC Bus and braking circuit terminals prior to shipment helps prevent
miswiring. Cut away covers as needed for terminals with a needle-nose pliers.

A – Protective Cover to Prevent Miswiring

2. The ground terminal screw on IP20/NEMA Type 1 holds the protective cover in place.
Main Circuit Connection Diagram
For drive main power circuit connections, refer to Figure 3.3 and Figure 3.4 on page 58.
WARNING! Fire Hazard. The braking resistor connection terminals are B1 and B2. Do not connect braking
resistors to any other terminals. Improper wiring connections could cause the braking resistor to overheat
and cause death or serious injury by fire. Failure to comply may result in damage to the braking circuit or
drive.

68 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 3.7 Control Circuit Wiring

3.7 Control Circuit Wiring

Figure 3.14

V1000
*1 Control circuit

Electrical Installation
Forward run/stop S1

Reverse run/stop S2
Option card
External fault S3 connector

Fault reset S4 DIP switch S1 Digital output

Multi-step V I 250 Vac, 10 mA to 1 A
speed 1 30 Vdc, 10 mA to 1 A
main/aux switch S5 (default setting)
Multi-step
speed 2 S6
MA Fault
Jog reference S7
+24 V 8 mA MB Digital output 3
24 V 5 ~ 48 Vdc
50 mA or less
*2
Digital inputs MC
(default setting) Sink (default setting)
DIP
switch S3 Source
SC
P1 During Run
Shield ground 0V (photocoupler 1)
terminal

P2 Frequency agree
(photocoupler 2)
Pulse train input
RP
(max. 32 kHz) PC Photocoupler
Setting power supply output common
+V
2 kΩ +10.5 max. 20 mA
MP Pulse train output
Main speed A1 0 to +10 V (20 kΩ) 0 to 32 kHz
frequency A2 0 to +10 V (20 kΩ) Analog monitor
AM
reference. (0)4 to 20 mA (250 Ω) + output
Multi-function AM
AC 0 to +10 Vdc
programmable AC - (2 mA)

Termination Comm.
DIP Monitor
resistor connector
switch output
Safety switch 120 Ω, 1/2 W
S2 R+
Safety HC
input R-
Jumper
H1 S+ MEMOBUS/
S- Modbus comm.
RS-485/422
IG

Cable shield ground

shielded line twisted-pair shielded line

main circuit terminal control terminal

Figure 3.14 Control Circuit Connection Diagram

* 1. Connected using sequence input signal (S1 to S7) from NPN transistor;Default:sink mode (0 V com)
* 2. Use only a +24 V internal power supply in sinking mode; the source mode requires an external power
supply. Refer to I/O Connections on page 77.

NOTICE: Do not solder the ends of wire connections to the drive. Soldered wire connections can loosen

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 69
3.7 Control Circuit Wiring

over time. Improper wiring practices could result in drive malfunction due to loose terminal connections.

◆ Control Circuit Terminal Block Functions

Drive parameters determine which functions apply to the multi-function digital inputs (S1 to
S7), multi-function digital outputs (MA, MB), multi-function pulse inputs and outputs (RP,
MP) and multi-function photocoupler outputs (P1, P2). The default is called out next to each
terminal. Refer to Figure 3.14 on page 69
WARNING! Sudden Movement Hazard. Always check the operation and wiring of control circuits after being
wired. Operating a drive with untested control circuits could result in death or serious injury.

WARNING! Confirm the drive I/O signals and external sequence before starting test run. Setting parameter
A1-06 may change the I/O terminal function automatically from the factory setting. Refer to Application
Presets on page 111. Failure to comply may result in death or serious injury.

NOTICE: Do not switch an input contactor more often than once every 30 minutes. Improper equipment
sequencing could shorten useful life of the drive electrolytic capacitors and circuit relays. Normally the drive
I/O should be used to stop and start the motor.

■ Input Terminals
Table 3.6 Control Circuit Input Terminals

Type No. Terminal Name (Function) Function (Signal Level) Default Setting

Multi-function input 1 (Closed: Forward

S1
run, Open: Stop)
Multi-function input 2 (Closed: Reverse
S2
run, Open: Stop)
Multi-function input 3 (External fault Photocoupler
S3 24 Vdc, 8 mA Note: Drive preset to sinking mode.
(N.O.))
Multi- When using source mode, set DIP switch S3 to allow
Function S4 Multi-function input 4 (Fault reset)
for a 24 Vdc (±10%) external power supply. Refer to
Digital Multi-function input 5 (Multi-step speed page 77.
Inputs S5
reference 1)
Multi-function input 6 (Multi-step speed
S6
reference 2)
S7 Multi-function input 7 (Jog reference)
Multi-function input common (Control
SC Sequence common
common)
HC Power supply for safety input command +24 Vdc (max 10 mA allowed)
Safety Open: Coast to stop safety input
Input H1 Safety input command Closed: Normal operation Note: Disconnect wire
jumper between HC and H1 when using safety input.

70 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 3.7 Control Circuit Wiring

Type No. Terminal Name (Function) Function (Signal Level) Default Setting

Response frequency: 0.5 to 32 kHz

(Duty Cycle: 30 to 70%)
Multi-function pulse train input (frequency
RP (High level voltage: 3.5 to 13.2 Vdc)
reference)
(Low level voltage: 0.0 to 0.8 Vdc)
(input impedance: 3 kΩ)

Electrical Installation
Main +V Analog input power supply +10.5 Vdc (max allowable current 20 mA)
Frequency
Multi-function analog input (frequency Input voltage 0 to +10 Vdc (20 kΩ) resolution 1/
Reference A1
reference) 1000
Input
Input voltage or input current (Selected by DIP
Multi-function analog input (frequency switch S1) 0 to +10 Vdc (20 kΩ) resolution: 1/1000
A2
reference) 4 to 20 mA (250 Ω) or 0 to 20 mA (250 Ω)
resolution: 1/500
AC Frequency reference common 0 Vdc 3
■ Output Terminals
Table 3.7 Control Circuit Output Terminals

Function (Signal Level)

Type No. Terminal Name (Function) Default Setting

MA N.O. (fault)
Multi-Function Digital output
MB N.C. output (fault)
Digital Output 30 Vdc, 10 mA to 1 A; 250 Vac, 10 mA to 1 A
MC Digital output common

Multi-Function P1 Photocoupler output 1 (during run)

Photocoupler P2 Photocoupler output 2 (Frequency agree) Photocoupler output 48 Vdc, 2 to 50 mA
Output PC Photocoupler output common
MP Pulse train output (input frequency) 32 kHz (max)
Monitor Output AM Analog monitor output 0 to 10 Vdc (2 mA or less) Resolution: 1/1000
AC Monitor common 0V

Connect a suppression diode as shown in Figure 3.15 when driving a reactive load such as a
relay coil. Ensure the diode rating is greater than the circuit voltage.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 71
3.7 Control Circuit Wiring

Figure 3.15

C
A D

A – External power, 48 V max. C – Coil

B – Suppression diode D – 50 mA or less

Figure 3.15 Connecting a Suppression Diode

■ Serial Communication Terminals

Table 3.8 Control Circuit Terminals: Serial Communications

Type No. Signal Name Function (Signal Level)

R+ Communications input (+)
MEMOBUS/Modbus
R- Communications input (-) RS-485/422 MEMOBUS/
MEMOBUS/ communication: Use a RS-485
Modbus communication
Modbus S+ Communications output (+) or RS-422 cable to connect the
protocol 115.2 kbps (max.)
Communication drive.
S- Communications output (-)
IG Shield ground 0V

◆ Removable Terminal Block Configuration

Figure 3.16

R+ R㧙 S+ S㧙 IG

P1 P2 PC A1 A2 +V AC AM AC MP

MA MB MC
R+ R㧙 S+ S㧙 IG S1 S2 S3 S4 S5 S6 S7 HC SC H1 RP

P1 P2 PC A1 A2 +V AC AM AC MP

MA MB MC
S1 S2 S3 S4 S5 S6 S7 HC SC H1 RP

Figure 3.16 Removable Control Circuit Terminal Block

(CIMR-VA ; CIMR-VU )

■ Wire Size and Torque Specifications

Select the appropriate wires and crimp terminals from Table 3.9. Crimp a ferrule to signal
wiring to improve wiring simplicity and reliability. Refer to Ferrule Terminal Types and
Sizes on page 73.

72 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 3.7 Control Circuit Wiring

Table 3.9 Wire Size and Torque Specifications (Same for All Models)

Bare Wire Terminal Ferrule-Type Terminal

Tightening Tightening Applicable
Screw Torque Applicable wire Recomm. wire size Recomm. Wire
Terminal Size
Torque
Type
Nxm (in-lbs) size mm2 mm2 mm2
mm2 (AWG) (AWG) (AWG)
(AWG)
Stranded: 0.25 to

Electrical Installation
MA, MB, 1.5 (24 to 16) 0.25 to 1.0
M3 0.5 to 0.6 4.4 to 5.3 0.75 (18) 0.5 (20)
MC Single: 0.25 to (24 to 18)
1.5 (24 to 16)
S1-S7, SC,
RP, +V, A1, Shielded
A2, AC, HC, Stranded: 0.25 to line, etc.
H1, P1, P2, 1.0 (24 to 18) 0.25 to 0.5
M2 0.22 to 0.25 1.9 to 2.2 0.75 (18) 0.5 (20)
PC, MP, Single: 0.25 to (24 to 20)
AM, AC,
S+, S-, R+,
1.5 (24 to 16)
3
R-, IG

■ Ferrule-Type Wire Terminations

Crimp a ferrule to signal wiring to improve wiring simplicity and reliability. Use
CRIMPFOX ZA-3, a crimping tool manufactured by PHOENIX CONTACT.
Figure 3.17

φd1
6 mm

φd2

Figure 3.17 Ferrule Dimensions

Table 3.10 Ferrule Terminal Types and Sizes

Size mm2 (AWG) Type L (mm) d1 (mm) d2 (mm) Manufacturer

0.25 (24) AI 0.25-6YE 10.5 0.8 2
0.34 (22) AI 0.34-6TQ 10.5 0.8 2
0.5 (20) AI 0.5-6WH 12 1.1 2.5 PHOENIX CONTACT
0.75 (18) A1 0.75-6GY 12 1.3 2.8
1.0 AI 1-6RD 12 1.5 3.0

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 73
3.7 Control Circuit Wiring

◆ Wiring Procedure
This section describes the proper procedures and preparations for wiring the terminal board.
WARNING! Electrical Shock Hazard. Do not remove covers or touch the circuit boards while the power is
on. Failure to comply could result in death or serious injury.

NOTICE: Separate control circuit wiring from main circuit wiring (terminals R/L1, S/L2, T/L3, B1, B2, U/T1,
V/T2, W/T3, -, +1, +2) and other high-power lines. Improper wiring practices could result in drive malfunction
due to electrical interference.

NOTICE: Separate wiring for digital output terminals MA, MB and MC from wiring to other control circuit
lines. Improper wiring practices could result in drive or equipment malfunction or nuisance trips.

NOTICE: Use a class 2 power supply (UL standard) when connecting to the control terminals. Improper
application of peripheral devices could result in drive performance degradation due to improper power
supply.

NOTICE: Insulate shields with tape or shrink tubing to prevent contact with other signal lines and
equipment. Improper wiring practices could result in drive or equipment malfunction due to short circuit.

NOTICE: Connect the shield of shielded cable to the appropriate ground terminal. Improper equipment
grounding could result in drive or equipment malfunction or nuisance trips.

Wire the terminal board using Figure 3.18 as a guide (control circuit terminal block). Be
sure to prepare the ends of the control circuit wiring as shown in Figure 3.19. Refer to Wire
Gauges and Tightening Torque on page 63 for tightening torque specifications.
NOTICE: Do not tighten screws beyond the specified tightening torque. Failure to comply may damage the
terminal block.

NOTICE: Use shielded twisted-pair cables as indicated to prevent operating faults. Improper wiring
practices could result in drive or equipment malfunction due to electrical interference.

74 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 3.7 Control Circuit Wiring

Figure 3.18

D
Preparing wire E
A terminal ends
B

Electrical Installation
C

A – Control terminal block D – Loosen screw to insert wire.

B – Avoid fraying wire strands when E – Blade depth of 0.4 mm or less
stripping insulation from wire. Blade width of 2.5 mm or less
Strip length 5.5 mm. 3
C – Single wire or stranded wire

Figure 3.18 Terminal Board Wiring Guide

Figure 3.19

A D
F C

E
B

A – Drive side D – Control device side

B – Connect shield to ground terminal E – Shield sheath
of drive. (Insulate with tape)
C – Insulation F – Shield

Figure 3.19 Preparing the Ends of Shielded Cables

When setting the frequency by analog reference from an external potentiometer, use shielded
twisted-pair wires and ground the shield of twisted-pair wires to the ground terminal of the
drive.
NOTICE: The analog signal lines between the drive and the operator station or peripheral equipment should
not exceed 50 meters when using an analog signal from a remote source to supply the frequency reference.
Failure to comply could result in poor system performance.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 75
3.7 Control Circuit Wiring

Figure 3.20

B
RP C
2k
+V D
G A1 E
A2 F

AC

A – Drive E – (A1) Main speed frequency

reference
0 to +10 Vdc (20 kΩ)
B – Ground terminal F – (A2) Multi-function analog input
(shield connection) 0 to +10 Vdc (20 kΩ) or
4 to 20 mA (250 Ω)/
0 to 20 mA (250 Ω)
C – (RP) Pulse train G – Frequency setting potentiometer
(maximum 32 kHz)
D – (+V) Frequency setting power source +10.5 Vdc maximum 20 mA

Figure 3.20 Wiring the Frequency Reference to the Control Circuit Terminals (External Reference)

76 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 3.8 I/O Connections

3.8 I/O Connections

◆ Sinking/Sourcing Mode Switch

Set the DIP switch S3 on the front of the drive to switch the digital input terminal logic
between sinking mode and sourcing mode; the drive is preset to sinking mode.

Electrical Installation
Table 3.11 Sinking/Sourcing Mode Setting

Set Value Details

SINK Sinking Mode (0 V common): factory setting
SOURCE Sourcing Mode (+24 V common)

Figure 3.21

DIP Switch S3 3
SINK

SOURCE

Figure 3.21 DIP Switch S3

■ Transistor Input Signal Using 0 V Common/Sink Mode

When controlling the digital inputs by NPN transistors (0 V common / sinking mode), set
the DIP switch S3 to SINK and use the internal 24 V power supply.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 77
3.8 I/O Connections

Figure 3.22

SINK

Shielded cable Drive

S1
Forward run/stop
S2
SOURCE Reverse run/stop
S3

Multi-function input
External fault N.O.
S4
Fault reset
S5
Multi-speed step 1
S6
Multi-speed step 2
S7
Jog reference
SINK
+24V
S3

SOURCE
SC

Figure 3.22 Sinking Mode: Sequence from NPN Transistor (0 V Common)

■ Transistor Input Signal Using +24 V Common/Source Mode

When controlling digital inputs by PNP transistors (+24 V common / sourcing mode), set the
DIP switch S3 to SOURCE and use an external 24 V power supply.
Figure 3.23

Shielded cable
Drive
SINK

Forward run / stop S1

Reverse run / stop S2

Multi-function input

External fault N.O. S3

SOURCE
External Fault rest S4
power supply
+24 V
Multi-step speed 1 S5

Multi-step speed 2 S6
Jog frequency S7

SINK
+24V
S3

SOURCE
SC

Figure 3.23 Source Mode: Sequence from PNP Transistor (+24 V Common)

78 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 3.9 Main Frequency Reference

3.9 Main Frequency Reference

◆ Terminal A2 Switch
The main frequency reference can either be a voltage or current signal input. For voltage
signals both analog inputs, A1 and A2, can be used, for current signals A2 must be used.

Electrical Installation
To use current input at terminal A2, set the DIP switch S1 to "I" (factory setting) and set
parameter H3-09 = “2” or “3” (4-20 mA or 0-20 mA). Set parameter
H3-10 = “0” (frequency reference).
Note: If Terminals A1 and A2 are both set for frequency reference (H3-02 = 0
and H3-10 = 0), the addition of both input values builds the frequency reference.
When using input A2 as voltage input, set the DIP switch S1 to “V” (left position) and
program parameter H3-09 to “0” (0 to +10 Vdc with lower limit) or “1” (0 to +10 Vdc
without lower limit).
3
Table 3.12 Frequency Reference Configurations

Voltage Input Current Input

Drive Drive

+10.5 V
+V +10.5 V
20 mA current
+V 20 mA current

0 to 10 V Main speed Main speed

2 kΩ A1 frequency reference 4 to 20 mA input A1 frequency reference
(voltage input) (voltage input)
or
Main speed 0 to 20 mA input Main speed
A2 frequency reference A2 frequency reference
(current input) (current input)

AC Frequency reference AC Frequency reference

common common

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 79
3.9 Main Frequency Reference

Figure 3.24

DIP Switch S1
V I

Figure 3.24 DIP Switch S1

Table 3.13 DIP Switch S1 Settings

Setting Value Description

V (left position) Voltage input (0 to 10 V)
I (right position) Current input (4 to 20 mA or 0 to 20 mA): factory setting

Table 3.14 Parameter H3-09 Details

Setting Default
No. Parameter Name Description Range Setting
Selects the signal level for terminal A2.
0: 0 to +10 V, unipolar input (negative frequency
reference values are zeroed)
Frequency ref. (current)
H3-09 1: 0 to +10 V, bipolar input (negative frequency 0 to 3 2
terminal A2 signal level selection
reference changes the direction)
2: 4 to 20 mA
3: 0 to 20 mA

80 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 3.10 MEMOBUS/Modbus Termination

3.10 MEMOBUS/Modbus Termination

DIP switch S2 controls the terminal resistance as shown in the Figure 3.25. The OFF
position is the default of the terminating resistor switch for MEMOBUS/Modbus
communications. Turn the terminal resistor switch ON when the drive is the last drive in a
series of slave drives.

Electrical Installation
Table 3.15 MEMOBUS/Modbus Switch Settings

S2 Position Description
ON Internal terminal resistance ON
OFF Internal terminal resistance OFF (no terminal resistance); default setting

Figure 3.25

DIP Switch S2 3
OFF ON

Figure 3.25 DIP Switch S2

Note: Refer to the MEMOBUS/Modbus communications manual for details on MEMOBUS/Modbus.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 81
3.11 Braking Resistor

3.11 Braking Resistor

Dynamic braking (DB) helps bring the motor to a smooth and rapid stop when working with
high inertia loads. As the drive lowers the frequency of a motor with high inertia connected,
regeneration occurs. This can cause an overvoltage situation when the regenerative energy
flows back into the DC bus capacitors. A braking resistor prevents these overvoltage faults.
NOTICE: Do not allow unqualified personnel to use the product. Failure to comply could result in damage to
the drive or braking circuit. Carefully review the braking resistor instruction manual when connecting a
braking option to the drive.

Note: The braking circuit must be sized properly in order to dissipate the power required to decelerate
the load in the desired time. Ensure that the braking circuit can dissipate the energy for the set
deceleration time prior to running the drive.
Use a thermal overload relay or an over-temperature contact to interrupt input power to the
drive in the event the braking resistor overheats.
In the event of a possible thermal overload, the relay will trigger the input contactor and
prevent the braking resistor from burning up.

◆ Installation
WARNING! Fire Hazard. The braking resistor connection terminals are B1 and B2. Do not connect a braking
resistor directly to any other terminals. Improper wiring connections could result in death or serious injury by
fire. Failure to comply may result in damage to the braking circuit or drive.

NOTICE: Connect braking resistors to the drive as shown in the I/O wiring examples. Improperly wiring
braking circuits could result in damage to the drive or equipment.

■ Installation Procedure
1. Disconnect all electrical power to the drive and wait at least five minutes before
servicing the drive and any connected components.
2. Remove drive front cover.
3. Use a voltmeter to verify that voltage is disconnected from incoming power
terminals and that the DC bus no longer holds a charge.

82 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 3.11 Braking Resistor

Figure 3.26

Thermal
relay Braking resistor

Power
supply MCCB MC
R/L1 B1 B2

S/L2 U/T1
T/L3 V/T2 Motor
W/T3
THRX OFF ON MC
Drive

Electrical Installation
SA
MC
THRX

SA
Thermal relay switch for
external braking resistor

MC TRX

SA
TRX
MA MC
Fault contact

Figure 3.26 Connecting a Braking Resistor

4. Follow maufacturer instructions to connect the resistor unit to the drive using proper
3
wire gauge according to local electrical codes.
Power leads for the remote mount resistors generate high levels of electrical noise;
group these signal leads separately.
5. Mount the resistor unit on a noncombustible surface. Maintain minimum side and
top clearances according to resistor manufacturer instructions.
WARNING! Fire Hazard. Do not use improper combustible materials. Failure to comply could result in death
or serious injury by fire. Attach the drive or braking resistors to metal or other noncombustible material.

6. Reinstall drive covers and resistor covers, if provided.

■ Adjustments
7. Set parameter L3-04 = “0” or “3” to disable stall prevention during deceleration.
Set parameter L8-01= “1” to enable overheat protection when using Yaskawa
heatsink mounted braking resistor. Set L8-01 = “0” for other braking resistor types.
Set parameter L3-04 = “3” to generate the shortest possible deceleration time.
Table 3.16 Braking Resistor Settings

Parameter Settings
0: Disabled. The drive will not provide overheat
L8-01: Internal Dynamic Braking Resistor Protection
protection. Supply separate means of overheat protection.
selection
1: Enabled. Braking Resistor is protected from overheat.
0: Stall prevention disabled.
L3-04: Stall Prevention During Deceleration <1>
3: Stall prevention enabled with a braking resistor. <2>

<1> Select either 0 or 3.

<2> This setting cannot be used in OLV control for PM motor.

■ Operation Check
8. Operate the system and verify the required deceleration rate is obtained during
dynamic braking or stopping.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 83
3.12 Wiring Checklist

3.12 Wiring Checklist

No. Item Page

Drive, peripherals, option cards

1 Check drive model number to ensure receipt of correct model. 25
Check for correct braking resistors, DC reactors, noise filters, and other peripheral
2 82
devices.
3 Check for correct option card model. 286
Installation area and physical setup
4 Ensure area surrounding the drive complies with specifications. 41
Power supply voltage, output voltage
The voltage from the power supply should fall within the input voltage specification
5 138
range of the drive.
25
6 The voltage rating for the motor should match the drive output specifications.
122
Main circuit wiring
7 Confirm proper branch circuit protection exists per National and Local codes. 55

8 Properly wire the power supply to drive terminals R/L1, S/L2 and T/L3. 58
Properly wire the drive and motor together.
The motor lines and drive output terminals R/T1, V/T2 and W/T3 should match in order
9 66
to produce the desired phase order. If the phase order is incorrect, the drive will rotate in
the opposite direction.
10 Use 600 Vac vinyl-sheathed wire for the power supply and motor lines. 63
Use the correct wire gauges for the main circuit. Refer to Table 3.2, Table 3.3, or
11 63
Table 3.4.
• When using comparatively long motor cable, calculate the amount of voltage drop.
Motor rated voltage (V) x 0.02 ≥ 63
-3
3 x voltage resistance (Ω/km) x cable length (m) x motor rated current (A) x 10

• If the cable between the drive and motor exceeds 500 m, adjust the carrier frequency 67
(C6-02) accordingly. 135
12 Properly ground the drive. Review page 67. 67
Tightly fasten all terminal screws (control circuit terminals, grounding terminals).
13 63
Refer to Table 3.2, Table 3.3 or Table 3.4.

84 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 3.12 Wiring Checklist

No. Item Page

Set up overload protection circuits when running multiple motors from a single drive.

Power supply Drive MC1 OL1

M1

Electrical Installation
MC2 OL2
14 M2

MCn OLn
Mn

MC1 - MCn ... magnetic contactor

O L 1 - OLn ... thermal relay
Note: Close MC1 through MCn before operating the drive.
If using a braking resistor or dynamic braking resistor unit, install a magnetic contactor.
3
15 Properly install the resistor, and ensure that overload protection shuts off the power 82
supply.
16 Verify phase advancing capacitors are NOT installed on the output side of the drive.
Control circuit wiring
17 Use twisted-pair cables for all drive control circuit wiring. 69

18 Ground the shields of shielded wiring to the GND terminal. 78

If using a 3-wire sequence, properly set parameters for multi-function contact input
19 57
terminals S1 through S7, and properly wire control circuits.
20 Properly wire any option cards. 287
Check for any other wiring mistakes.
21 -
Only use a multimeter to check wiring.
Properly fasten the control circuit terminal screws in the drive.
22 63
Refer to Table 3.2, Table 3.3 or Table 3.4.
23 Pick up all wire clippings.
Ensure that no frayed wires on the terminal block are touching other terminals or
24
connections.
25 Properly separate control circuit wiring and main circuit wiring.

26 Analog signal line wiring should not exceed 10 m.

27 All other wiring should be less than 50 m.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 85
3.12 Wiring Checklist

86 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 4
Start-Up Programming
& Operation
This chapter explains the functions of the LED operator and
how to program the drive for initial operation.

4.1 SECTION SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88

4.2 USING THE DIGITAL LED OPERATOR . . . . . . . . . . . . . . 91
4.4 START-UP FLOWCHARTS . . . . . . . . . . . . . . . . . . . . . . . . 97
4.6 BASIC DRIVE SETUP ADJUSTMENTS . . . . . . . . . . . . . 122
4.7 TEST RUN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
4.8 TEST RUN CHECKLIST. . . . . . . . . . . . . . . . . . . . . . . . . . 171

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 87
4.1 Section Safety

4.1 Section Safety

DANGER
Electrical Shock Hazard
Do not connect or disconnect wiring while the power is on.
Failure to comply will result in death or serious injury.

WARNING
Electrical Shock Hazard
Do not operate equipment with covers removed.
Failure to comply could result in death or serious injury.
The diagrams in this section may include drives without covers or safety
shields to illustrate details. Be sure to reinstall covers or shields before
operating the drives and run the drives according to the instructions
described in this manual.

Always ground the motor-side grounding terminal.

Improper equipment grounding could result in death or serious injury by
contacting the motor case.

Do not touch any terminals before the capacitors have fully

discharged.
Failure to comply could result in death or serious injury.
Before wiring terminals, disconnect all power to the equipment. The
internal capacitor remains charged even after the power supply is turned
off. The charge indicator LED will extinguish when the DC bus voltage is
below 50 Vdc. To prevent electric shock, wait at least five minutes after all
indicators are off and measure the DC bus voltage level to confirm safe
level.

88 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 4.1 Section Safety

WARNING
Do not allow unqualified personnel to perform work on the drive.
Failure to comply could result in death or serious injury.
Installation, maintenance, inspection, and servicing must be performed
only by authorized personnel familiar with installation, adjustment and

Start-Up Programming &

maintenance of AC drives.

Do not perform work on the drive while wearing loose clothing,

jewelry or without eye protection.
Failure to comply could result in death or serious injury.

Operation
Remove all metal objects such as watches and rings, secure loose clothing,
and wear eye protection before beginning work on the drive.

Do not remove covers or touch circuit boards while the power is on. 4
Failure to comply could result in death or serious injury.

Fire Hazard
Tighten all terminal screws to the specified tightening torque.
Loose electrical connections could result in death or serious injury by fire
due to overheating of electrical connections.

Do not use an improper voltage source.

Failure to comply could result in death or serious injury by fire.
Verify that the rated voltage of the drive matches the voltage of the
incoming power supply before applying power.

Do not use improper combustible materials.

Failure to comply could result in death or serious injury by fire.
Attach the drive to metal or other noncombustible material.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 89
4.1 Section Safety

NOTICE
Observe proper electrostatic discharge procedures (ESD) when
handling the drive and circuit boards.
Failure to comply may result in ESD damage to the drive circuitry.

Never connect or disconnect the motor from the drive while the drive
is outputting voltage.
Improper equipment sequencing could result in damage to the drive.

Do not use unshielded cable for control wiring.

Failure to comply may cause electrical interference resulting in poor
system performance. Use shielded twisted-pair wires and ground the shield
to the ground terminal of the drive.

Do not allow unqualified personnel to use the product.

Failure to comply could result in damage to the drive or braking circuit.
Carefully review instruction manual TOBPC72060000 when connecting a
braking option to the drive.

Do not modify the drive circuitry.

Failure to comply could result in damage to the drive and will void
warranty.
Yaskawa is not responsible for any modification of the product made by the
user. This product must not be modified.

Check all the wiring to ensure that all connections are correct after
installing the drive and connecting any other devices.
Failure to comply could result in damage to the drive.

90 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 4.2 Using the Digital LED Operator

4.2 Using the Digital LED Operator

Use the LED operator to enter run and stop commands, display data, edit parameters, as well
as display fault and alarm information.

◆ Keys, Displays, and LEDs

Start-Up Programming &

12 13

Operation
1 11
5

4
2

15
3
14

STOP

7 8
10
4 6

STOP

V1000
Fref : (Hz)
FWD/REV Sel :
Fout : (Hz)
lout : (A)
Mon1 : (V)
Monitor :
Verify :
SetUpGuide :
Program :
Auto-Tuning :

WARNING Risk of electric shock.

Read manual before installing.
Wait 1 minute for capacitor discharge after
disconnecting power supply.
To conform to requirements, make sure to
ground the supply neutral for 400V class.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 91
4.2 Using the Digital LED Operator

Table 4.1 Keys and Displays on the LED Operator

No. Display Name Function

1 Data Display Area Displays the frequency reference, parameter number, etc.

2 ESC Key Returns to the previous menu.

Moves the cursor to the right.

3 RESET Key
Resets the drive to clear a fault situation.

4 RUN RUN Key Starts the drive.

5 Up Arrow Key Scrolls up to select parameter numbers, setting values, etc.

6 Down Arrow Key Scrolls down to select parameter numbers, setting values, etc.

Stops the drive.

STOP Note: Stop priority circuit. A fast-stop is available by pressing
the STOP key when the drive detects a danger even if the drive
7 STOP Key is running by a signal from the multi-function contact input
terminal (REMOTE is set). To avoid stoppage by using the
STOP key, set o2-02 (STOP Key Function Selection) to 0
(Disabled).
Selects all modes, parameters, settings, etc.
8 ENTER Key Selects a menu item to move from one display screen to the
next.
Switches drive control between the operator (LOCAL) and the
control circuit terminals (REMOTE).
Note: LOCAL/REMOTE key effective during stop in drive
9 LO/RE Selection Key mode. If the digital operator could change from REMOTE to
LOCAL by incorrect operation, set o2-01 (LOCAL/REMOTE
Key Function Selection) to “0” (disabled) to disable LOCAL/
REMOTE key.

10 RUN Light Lit while the drive is operating the motor.

11 LO/RE Light Lit while the operator (LOCAL) is selected to run the drive.

92 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 4.2 Using the Digital LED Operator

No. Display Name Function

12 ALM LED Light

13 REV REV LED Light

Refer to LED Screen Displays on page 94.
14 DRV LED Light

15 FOUT LED Light

Start-Up Programming &

◆ Digital Text Display
Text appears on the LED Operator as shown below. This section explains the meaning of

Operation
text as it appears on the display screen.

Lit Flashing
4

Table 4.2 Digital Text Display

Text LED Text LED Text LED Text LED

0 9 I R

1 A J S

2 B K T

3 C L U

4 D M V
<1>

5 E N W
<1>

6 F O X none

7 G P Y

8 H Q Z none
<1> Displayed in two digits.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 93
4.2 Using the Digital LED Operator

◆ LED Screen Displays

Display Lit Flashing Off
• When an alarm occurs
When the drive detects a alarm • OPE detected
Normal state (no fault or alarm)
or error • When a fault or error occurs
during Auto-Tuning

Motor is rotating in reverse — Motor is rotating forward

REV
Drive Mode
When DriveWorksEZ is used <1> Programming Mode
Auto-Tuning

Displays output frequency (Hz) — —

As
illustrated in
this manual
<1> Refer to the DriveWorksEZ instruction manual for further information.

◆ LO/RE LED and RUN LED Indications

LED Lit Flashing Flashing Quickly Off
When run command Run command is selected
is selected from LED — — from device other than LED
operator (LOCAL) operator (REMOTE)
• During deceleration to • During deceleration at
stop a fast-stop.
During run • When a run command • During deceleration During stop
is input and frequency • During stop by
reference is 0 interlock operation.

As shown

<1> For the difference between “flashing” and “flashing in short intervals” of the RUN LED, refer to Figure 4.2, RUN
LED and Drive Operation.

94 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 4.2 Using the Digital LED Operator

Figure 4.1

1s

ON ON
flashing

ON ON ON ON
quick

Start-Up Programming &

flashing
Figure 4.1 RUN LED Status and Meaning
Figure 4.2

drive output frequency

Operation
during stop RUN STOP RUN STOP
/ 6 Hz
0 Hz
frequency setting
RUN LED OFF ON ON OFF
4
Flashing
Figure 4.2 RUN LED and Drive Operation

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 95
4.2 Using the Digital LED Operator

◆ Menu Structure for Digital LED Operator

Figure 4.3

Description of Key Operations

:
Turn the power on

* :
*Pressing RUN will start the motor.
Forward Selection Reverse Selection
:
DRV light is on.

:
Output Frequency

Output Current

Note: “XX” characters are shown in this manual.

The drive will display the actual setting values.
Output Voltage

XX
Monitor Display

XX

XX XX XX
Verify Menu

XX XX XX
*Drive cannot operate the motor.

XX
DRV light is off.

Set Up Mode

XX XX XX

XX
Parameter Setting Mode

XX

Auto-Tuning

XX

Figure 4.3 Digital LED Operator Screen Structure

* “rEu” can be selected while LOCAL is set.

96 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 4.3 The Drive and Programming Modes

4.3 The Drive and Programming Modes

The drive functions are divided into two main groups accessible via the Digital LED
Operator:
Drive Mode: The Drive mode allows motor operation and parameter monitoring. Parameter
settings cannot be changed when accessing functions in the Drive Mode (Table 4.2).
Programming Mode: The Programming Mode allows access to setup/adjust, verify

Start-Up Programming &

parameters and Auto-Tuning. The drive prohibits changes in motor operation such as start/
stop when the Digital LED Operator is accessing a function in the Programming Mode.
Table 4.2 illustrates the different functions visible as the “Up arrow” is scrolled immediately
after powering up the drive.
Note: When b1-08 (Run Command Selection while in Programming Mode) is set to 1 (enabled), the

Operation
drive can run even if the mode is switched to the programming mode. When setting b1-08 to 0
(disabled), the mode cannot be switched to the programming mode while the drive is running.
Table 4.3 Summary ofModes

Mode Group Description Key Press LED Digital Operator Display

4
Frequency Reference Display
(Initial power-up state)

Forward/Reverse

Output Frequency Display

Drive Mode Functions (Motor
operation
and monitoring) Output Current Display

Output Voltage Reference

Monitor Display

Verify Function

Setup Group Parameters

Programming Mode
Functions
(Changing parameters)
All Parameters

Auto-Tuning

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 97
4.3 The Drive and Programming Modes

◆ Navigating the Drive and Programming Modes

The drive is set to operate in Drive Mode when it is first powered up. Switch between
display screens by using the and keys.

Frequency Reference

This display screen allows the user to monitor and set the frequency
reference while the drive is running. Refer to The Drive and
Power Up Programming Modes on page 97.
Note: The user can select items to display when the drive is first
STOP powered up by setting parameter o1-02.

Default Setting

: Motor rotates forward.

: Motor rotates in reverse.
Note: For applications that should not run in reverse (fans, pumps,
Forward/Reverse etc.), set parameter b1-04 = ”1” to prohibit the motor from rotating
in reverse. This sequence also puts the drive in LOCAL mode.
Switching to reverse:

The LED is lit when

LOCAL is selected

Drive Mode

Output Frequency Display

Monitors the frequency output by the drive.

Output Current Display

Monitors the output current of the drive.

98 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 4.3 The Drive and Programming Modes

Output Voltage Reference

(Default setting)
Scroll through o1-01 (User Monitor Selection) until the desired
contents appear. Refer to Parameter List on page 309

Drive Mode

Monitor Display

Start-Up Programming &

Monitor parameters (U-parameters) are displayed. Refer to
Drive Status Monitors: U1-01 to U6-19 on page 150.

Operation
Verify Function
Lists all parameters that have been edited or changed from default
settings. Refer to Verifying Parameter Changes: Verify Menu
on page 102.
4

Setup A select list of parameters necessary to get the drive operational

quickly. Refer to The Setup Group within the Programming
Mode on page 101. Note: Parameters to be displayed differ
depending on the setting of A1-06 (Application Preset). Refer to
Application Presets on page 111.
Programming
Mode

Parameter Setting
Allows the user to access and edit all parameter settings. Refer
to Parameter List on page 309.

Auto-Tuning
Motor parameters are calculated and set automatically. Refer to
Auto-Tuning on page 153.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 99
4.3 The Drive and Programming Modes

Frequency Reference
Drive Mode Returns to the frequency reference display screen.

■ Drive Mode Details

The following actions are possible in the Drive Mode:
• Run and stop the drive.
• Monitor the operation status of the drive (frequency reference, output frequency, output
current, output voltage, etc.).
• View information on an alarm.
• View a history of alarms that have occurred.

Note: Select "Drive Mode" when running. The mode can be switched to any mode (program mode,
etc.) other than drive mode while the drive is stopped. However, the drive cannot be operated in
other modes. Return the mode to "Drive Mode" after completing periodic inspection.
Figure 4.4 illustrates changing the default frequency reference of F 0.00 (0 Hz) to F 6.00 (6
Hz) while in Drive Mode. This example assumes the drive is set to LOCAL.
Figure 4.4

Frequency reference
display at power up

STOP
Press to select LOCAL Press to select the
digit to the right

Press until the frequency

reference becomes 6 Hz

Figure 4.4 Setting the Frequency Reference while in Drive Mode

Note: The drive will not accept a frequency reference set value unless the ENTER key is pressed after
the frequency reference is entered. This feature prevents accidental setting of the frequency
reference. By setting o2-05 (Frequency Reference Setting Method Selection) to 1 (Enabled), the
drive will accept the frequency reference while it is being adjusted on the digital operator.

100 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 4.3 The Drive and Programming Modes

■ Programming Mode Details

The following actions are possible in the programming mode:
• Verify Function: Verify parameter setting changes from original default values.
• Setup Group: Access a list of commonly used parameters to simplify setup.
• Parameter Setting Mode: Access and edit all parameter settings.
• Auto-Tuning: Automatically caluclates and sets motor parameters for Open Loop or PM
Vector control to optimize the drive for the motor characteristics.
The Setup Group within the Programming Mode

Start-Up Programming &

In Setup Group, the user can access the minimum group of parameters required to operate
the application.
Note: Setup Group parameters are listed in Appendix B, and indicated with the letter “S” in the Access
Level column.

Operation
Note: Pressing ENTER from APPL navigates to the Application Preset setting display. When the set
value is changed, the parameter is changed to the optimum value for each application. It is set to
0 (General-purpose) prior to shipment. Refer to Application Presets on page 111.
Figure 4.5 illustrates the keys to press to enter the Setup Group.
In this example, the source of the frequency reference is changed from the control circuit 4
terminals to the LED Operator (i.e., b1-01 is changed from 1 to 0).
Figure 4.5
appears when powered up


STOP Press until

appears

Parameter Display Control Circuit Terminal

Select digit
to edit

LED Operator Parameter Display

*1 Pressing ENTER from APPL navigates to the Application Preset setting display.
When the set value is changed, the parameter is changed to the optimum value for
each application. It is set to 0 (General-purpose) prior to shipment.
*2 Move to the right to change parameter settings. Scroll down to view and check
settings in the Setup Mode
*3 To return to the Top Menu, press . To view or edit other parameters,

press and .

Figure 4.5 Setup Group Example

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 101
4.3 The Drive and Programming Modes

◆ Changing Parameter Settings or Values

This example explains changing C1-01 (Acceleration Time 1) from 10.0 seconds (default) to
20.0 seconds.

Step Display/Result

1. Turn on the power to the drive. The initial display appears. ⇒

2. Press the key until the Setup Mode Screen appears. ⇒

3. Press the key to view the parameter setting display. ⇒

4. Scroll through parameters by pressing the key until C1-01

⇒
appears.

5. Press to view the current setting value (10.0 seconds).

⇒
(Number farthest to the left flashes)
6. Press until the desired number is selected. (“1” flashes) ⇒

7. Press the key and enter 0020.0. ⇒

8. Press and the drive will confirm the change. ⇒

9. The display automatically returns to the screen shown in Step 4. ⇒

10. Press the key until back at the initial display. ⇒

◆ Verifying Parameter Changes: Verify Menu

The Verify Menu lists edited parameters from the Programming Mode or as a result of Auto-
Tuning. The Verify Menu helps determine which settings have been changed, and is
particularly useful when replacing a drive. If no settings have been changed and all
parameters remain at the original default settings, then the Verify Menu will read .
The Verify menu also allows users to access and re-edit edited parameters.
Note: The Verify Menu will not display parameters from the A1 group (except for A1-02) even if those

102 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 4.3 The Drive and Programming Modes

parameters have been changed from default settings.

The example below is continued from page 102. Here, parameter C1-01 is accessed using
the Verify Menu and is changed again to 20.0 s.
To check the list of edited parameters:

Step Display/Result

Start-Up Programming &

1. Turn on the power to the drive. The initial display appears. ⇒

2. Press until the display reads, “Verify.” ⇒

Operation
Press to enter the list of parameters that have been edited
3. from their original default settings. ⇒

Scroll through the list by pressing the key.

4
4. Press the key until C1-01 appears. ⇒

5. Press the key to access the setting value.(number farthest ⇒

to the left flashes)

◆ Switching Between LOCAL and REMOTE

Entering the run command using the LED operator is referred to as LOCAL, while entering
the run command from an external device via the control circuit terminals or network option
card is referred to as Remote.
WARNING! Sudden Movement Hazard. The drive may start unexpectedly if the Run command is already
applied when switching from LOCAL mode to REMOTE mode when b1-07 = 1, resulting in death or serious
injury. Be sure all personnel are clear of rotating machinery and electrical connections prior to switching
between LOCAL mode and REMOTE mode.

There are three ways to switch between LOCAL and REMOTE.

Note: 1. After selecting LOCAL, LO/RE will remain lit.
2. The drive will not allow the user to switch between LOCAL and REMOTE during run.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 103
4.3 The Drive and Programming Modes

■ Using the LO/RE Key on the LED Operator

Step Display/Result

1. Turn on the power to the drive. The initial display appears. ⇒

Press . LO/RE will light up. The drive is now in Local.

2. To set the drive for REMOTE operation, press the key ⇒
STOP

again.

■ Using Input Terminals S1 through S7 to Switch between LO/RE

Switch between LOCAL and REMOTE using one of the digital input terminals S1 through
S7 (set the corresponding parameter H1-01 through H1-07 to “1”).
Follow the example below to set the digital input terminals.
Note: 1. For a list of digital input selections, Refer to Parameter List on page 309.
2. Setting a multi-function input terminal to a value of 1 disables the LO/RE key on the LED operator.

◆ Parameters Available in the Setup Group

■ Setup Mode (StUP)

Parameters used for this drive are classified into A to U. To simplify the drive setup,
frequently used parameters are selected and input into Setup Mode.

1. To set a parameter, the Setup Mode must be displayed first.

2. If the parameter setting is insufficient, set the parameters in the Parameter Setting
Mode.
Note: When parameter A1-02 (Control Method Selection) is changed, some parameter set values are
also changed automatically. Execute the A1-02 setting before Auto-tuning.
Table 4.4 lists parameters available in the Setup Group.
Note: This manual also explains other parameters not visible in the Setup Group (A1-06 = 0). Use the
“Par” menu in the Programming mode to access parameters not listed in the Setup Group. The
Setup Group parameters are shown in Table 4.4
Note: Display parameters depend on A1-06. Refer to Application Presets on page 111.

104 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 4.3 The Drive and Programming Modes

Table 4.4 Setup Group Parameters

Parameter Name Parameter Name

A1-02 Control Method Selection E1-01 Input Voltage Reference
b1-01 Frequency Reference Selection 1 E1-03 V/f Pattern Selection
b1-02 Run Command Selection 1 E1-04 Maximum Output Frequency (FMAX)
b1-03 Stop Method Selection E1-05 Maximum Voltage (VMAX)
C1-01 Acceleration Time 1 E1-06 Base Frequency (FA)

Start-Up Programming &

C1-02 Deceleration Time 1 E1-09 Minimum Output Frequency (FMIN)
C6-01 Duty Selection E1-13 Base Voltage (VBASE)
C6-02 Carrier Frequency Selection E2-01 Motor Rated Current
d1-01 Frequency Reference 1 E2-04 Number of Motor Poles

Operation
d1-02 Frequency Reference 2 E2-11 Motor Rate Capacity
d1-03 Frequency Reference 3 H4-02 Terminal FM Gain Setting
d1-04 Frequency Reference 4 L1-01 Motor Protection Function Selection
d1-17 Jog Frequency Reference L3-04 Stall Prevention Selection during Deceleration
4

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 105
4.4 Start-up Flowcharts

4.4 Start-up Flowcharts

The flowcharts in this section summarize basic steps required to start-up the drive. Use the
flowcharts to determine the most appropriate start-up method for a given application. The
charts are intended as a quick reference to help familiarize the user with start-up procedures.
Refer to Basic Drive Setup Adjustments on page 122 and perform all checks to ensure a
proper drive start-up.

Flowchart Subchart Objective Page

A Basic start-up procedure and motor tuning. 107
Simple motor set-up with Energy Savings or Speed Search using V/f
A-1 108
mode.
High-performance operation using Open Loop Vector (OLV) motor
A-2 109
control.
A-3 Operation with Permanent Magnet (PM) motors. 110
Set-up of drive using application specific selections. Refer to Application
- -
Presets on page 111

106 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 4.4 Start-up Flowcharts

◆ Flowchart A: Basic Start-Up and Motor Tuning

Figure 4.6, Flowchart A, describes basic start-up sequence for the drive and motor system.
This sequence varies slightly depending on application. Use drive default parameter settings
in simple applications that do not require high precision.
Figure 4.6

START

Install and wire the drive as explained in Chapters 1, 2 and 3

Start-Up Programming &

Apply main power on to the drive.
Adhere to safety messages concerning application of power

Application Presets
Yes
A1-06 used ?

Operation
TO
No
Set the control mode in parameter A1-02.
For information about the control modes refer to Section 4.5 Refer to section
4.4 Application
Macros

?
?
Set the basic parameters:
b1-01/02 for frequency reference and run command source selection
H1-,H2-,H3-,H4-,H6- for I/O terminal setting
)520
4
? d1- for multi-speed references if used
? C1- and C2- for accel./decel. and S-curve time settings
? C6-01 for heavy/normal duty mode selection
? L3-04 if braking options are used

0: V/f control Control Mode 5: Open Loop Vector for PM motors

A1-02 =

To To 2: Open Loop To
Flowchart A- Flowchart A- Vector control Flowchart A-
1 2 3

From Flowchart A-1, A-2, or A-3

Run the motor without load, check the rotation direction and operation. Verify, external signal
commands to the drive work as desired

Couple the load or machine to the motor. Run the machine and check it operates as desired

Fine tune parameters. Adjust application settings (PID, ...) if necessary

Check the machine operation and verify parameter settings.

Drive is ready to run the application

Figure 4.6 Basic Start-Up and Motor Tuning

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 107
4.4 Start-up Flowcharts

◆ Subchart A1: Simple Motor Set-Up with Energy Savings or

Speed Search using V/f Mode
Figure 4.7, Flowchart A1, describes simple motor set-up for V/f control. V/f Motor Control
is suited for the most basic applications such as fans or pumps. This procedure illustrates
using Energy Savings and Speed Estimation Speed Search. V/f control can be used where
rotational auto-tuning cannot be performed.
Figure 4.7

From
Flowchart
A

Set or verify the V/f pattern settings E1-.

Energy Savings
(b8-01=1)
or
Speed Estimation
NO Speed Search (b3-24=1)
enabled ? YES

Is the motor cable

longer than 50 m? Perform Rotational Auto-Tuning
for V/f Control
(T1-01 = 3)

YES
NO
Perform Stationary Auto-Tuning for
terminal resistance (T1-01 = 2)

Return to
Flowchart
A

Figure 4.7 Simple Motor Set-Up with Energy Savings or Speed Search Using V/f Mode

108 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 4.4 Start-up Flowcharts

◆ Subchart A2: High Performance Operation Using Open Loop

Vector Motor Control
Figure 4.8, Flowchart A2, uses Open Loop Vector Control for high-performance motor
operation. This is appropriate for applications requiring high starting torque, torque limits,
and improved speed regulation.
Figure 4.8

From

Start-Up Programming &

Flowchart
A

Operation
NO Possible for motor to
YES
rotate during tuning? *

Motor test report/ data

NO
*Rotational tuning should
be performed with the 4
sheet available? load disconnected

YES

Calculate necessary E2-

Enter the data from the motor data Perform Rotating Auto-
parameter data using the
sheet to E2- parameters. Tuning (T1-01 = 0)
nameplate information.

Is the motor cable

YES
longer than 50 m?

Perform Stationary Auto-Tuning for

NO terminal resistance (T1-01 = 2)

Return to
Flowchart
A

Figure 4.8 Flowchart A2: High Performance Operation

Using Open Loop Vector Motor Control

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 109
4.4 Start-up Flowcharts

◆ Subchart A3: Operation with Permanent Magnet Motors

Figure 4.9, Flowchart A3, illustrates tuning for PM motors in Open Loop Vector Control.
PM motors can be used for energy savings in reduced or variable torque applications.
Figure 4.9

From
Flowchart
A

Motorcode is known ?
For parameter E5-01 NO
(for Yaskawa PM motors)
YES Enter “FFFF” to parameter E5-
01

Set the motor code to Enter the motor data into

parameter E5-01 parameters E5-02 to E5-24

Return to
Flowchart
A

Figure 4.9 Operation with Permanent Magnet Motorsl

110 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 4.5 Application Presets

4.5 Application Presets

◆ Application Preset Function (APPL)

This drive incorporates a function to set the parameters automatically for the applications

Start-Up Programming &

that are frequently used. Using this Application Preset Function can set or run the drive
easily.

1: Water supply pump 2: Conveyor 3: Air supply/exhaust fan

Operation
4: AHU (HVAC) fan 5: Compressor 6: Hoist (elevator)
7: Cranes (traverse, traveling)

Note: For the details of these functions, Refer to Application Presets on page 111.
4
2WOR %QPXG[QT (CP

◆ Application Presets: A1-06

The drive features application presets to facilitate the set up of commonly used applications
such as a water supply pump, conveyor, exhaust fan, HVAC fan, compressor, hoist, and
crane. Selecting one of these presets automatically sets the required parameters to the
optimum values and changes the appropriate I/O terminal settings for that specific
application.
Verify all I/O signals and external sequences before operating the motor. Refer to Hoist
Application Preset Specifics on page 118 when selecting a hoist application.
Users are able to make further adjustments to these settings using the Setup Mode.

No. Parameter Name Setting Range Default

0: General-purpose (A2 parameters are not affected)
1: Water supply pump
2: Conveyor
3: Exhaust fan 0
A1-06 Applicaton Presets
4: HVAC fan <1>
5: Air compressor
6: Hoist
7: Crane (hoist, traverse)

<1> All general-purpose parameters are accessible when A1-06 = 0.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 111
4.5 Application Presets

WARNING! Confirm the drive I/O signals and external sequence before starting test run. Setting parameter
A1-06 may change the I/O terminal function automatically from the factory setting. Failure to comply may
result in death or serious injury.

Perform a 2-wire or 3-wire initialization (A1-03 = 2220 or 3330) on the drive before
selecting one of the application presets or before switching between application presets. The
initialization process should reset drive parameters before using an application preset.
Save user-edited parameters to a list by setting o2-03 to “1”. This allows for more immediate
access a specific list of relevant parameters and saves time scrolling through the parameter
menu items.
Set the parameter access level for Preferred Parameters (A1-01 = “1”) to display only the
setup parameters.
The parameters listed in the table below are unaffected by drive initialization:

No. Parameter Name

A1-02
Control Method Selection
<1>
C6-01 Duty Selection
E1-03 V/f Pattern Selection
E5-01 Motor Code Selection (for PM motors)
o2-04 Drive/kVA Selection

<1> The control method set to A1-02 is unaffected when performing a 2-wire or 3-wire intialization, but it
automatically changes according to the value set to parameter A1-06.

■ Related Parameters

No. Parameter Name Setting Range Default

0: Operation only
Access Level 1: User Parameters (access to a set of parameters selected by the 2
A1-01
Selection user) <1>
2: Advanced Access Level
0: No Initialize
1110: User Initialize (The user must first set user parameter values
and then store them using parameter o2-03)
A1-03 Initialize Parameters 2220: 2-Wire Initialization 0
3330: 3-Wire Initialization
4440: DriveWorksEZ Initialization
5550: OPE04 Error Reset
A2-02
User Parameters,
to b1-01 to o2-08 <1>
2 to 32
A2-32

112 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 4.5 Application Presets

No. Parameter Name Setting Range Default

0: Parameters A2-01 through A2-32 are reserved for the user to
User Parameter create a list of User Parameters. 1
A2-33
Automatic Selection 1: Save history of recently viewed parameters. Recently edited <2>
parameters will be saved to A2-17 through A2-32 for quick access.
0: No Change
User Parameter 1: Set Defaults - Saves current parameter settings as user
o2-03 0
Default Value initialization.
2: Clear All - Clears the currently saved user initialization.

Start-Up Programming &

<1> Default setting value is dependent on parameter A1-06, Application Selection
<2> Default setting value is dependent on parameter A1-06. This setting value is 0 when A1-06 = 0, and 1 when A1-06
does not = 0.

■ Application Presets

Operation
Below is a list of application presets and the values automatically assigned to the parameters
as a result of each preset:
Table 4.5 Water Supply Pump Application: Parameters and Settings

No. Parameter Name Optimum Setting

4
A1-02 Control Method Selection 0: V/f Control
b1-04 Reverse Operation Selection 1: Reverse prohibited
C1-01 Acceleration Time 1 1.0 s
C1-02 Deceleration Time 1 1.0 s
C6-01 Duty Rating 1: Normal Duty
E1-03 V/f Pattern Selection 0FH
E1-07 Mid Output Frequency (FB) 30.0
E1-08 Mid Output Frequency Voltage (VC) 50.0
L2-01 Momentary Power Loss Operation Selection 1: Enabled
L3-04 Stall Prevention Selection during Deceleration 1: Enabled

Table 4.6 Parameters Automatically Saved as Preferred (A2-01 to A2-16)

No. Parameter Name No. Parameter Name

b1-01 Frequency Reference Selection E1-08 Mid Output Frequency Voltage (VC)
b1-02 Run Command Selection E2-01 Motor Rated Current
Multi-Function Digital Input Terminal
b1-04 Reverse Operation Selection H1-05
S5 Function Selection
Multi-Function Digital Input Terminal
C1-01 Acceleration Time 1 H1-06
S6 Function Selection
Multi-Function Digital Input Terminal
C1-02 Deceleration Time 1 H1-07
S7 Function Selection

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 113
4.5 Application Presets

No. Parameter Name No. Parameter Name

E1-03 V/f Pattern Selection L5-01 Number of Auto Restart Attempts
E1-07 Mid Output Frequency (FB)

Table 4.7 Conveyor Application: Parameters and Settings

No. Parameter Name Optimum Setting

A1-02 Control Method Selection 0: V/f Control
C1-01 Acceleration Time 1 3.0 s
C1-02 Deceleration Time 1 3.0 s
C6-01 Duty Rating 0: Heavy Duty
L3-04 Stall Prevention Selection during Deceleration 1: Enabled

Table 4.8 Parameters Automatically Saved as Preferred (A2-01 to A2-16)

No. Parameter Name No. Parameter Name

A1-02 Control Method Selection C1-02 Deceleration Time 1
b1-01 Frequency Reference Selection E2-01 Motor Rated Current
Stall Prevention Selection during
b1-02 Run Command Selection L3-04
Deceleration
C1-01 Acceleration Time 1

Table 4.9 Exhaust Fan Application: Parameters and Settings

No. Parameter Name Optimum Setting

A1-02 Control Method Selection 0: V/f Control
b1-04 Reverse Operation Selection 1: Reverse Prohibited
C6-01 Duty Selection 1: Normal Duty
E1-03 V/f Pattern Selection 0FH
E1-07 Mid Output Frequency (FB) 30
E1-08 Mid Output Frequency Voltage (VC) 50
L2-01 Momentary Power Loss Operation Selection 1: Enabled
L3-04 Stall Prevention Selection during Deceleration 1: Enabled

Table 4.10 Parameters Automatically Saved as Preferred (A2-01 to A2-16)

No. Parameter Name No. Parameter Name

b1-01 Frequency Reference Selection E1-07 Mid Output Frequency (FB)
b1-02 Run Command Selection E1-08 Mid Output Frequency Voltage (VC)
b1-04 Reverse Operation Selection E2-01 Motor Rated Current

114 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 4.5 Application Presets

No. Parameter Name No. Parameter Name

Multi-Function Digital Input Terminal
b3-01 Speed Search Selection at Start H1-05
S5 Function Selection
Multi-Function Digital Input Terminal
C1-01 Acceleration Time 1 H1-06
S6 Function Selection
Multi-Function Digital Input Terminal
C1-02 Deceleration Time 1 H1-07
S7 Function Selection
E1-03 V/f Pattern Selection L5-01 Number of Auto Restart Attempts

Start-Up Programming &

Table 4.11 HVAC Fan Application: Parameters and Settings

No. Parameter Name Optimum Setting

A1-02 Control Method Selection 0: V/f Control

Operation
b1-04 Reverse Operation Selection 1: Reverse prohibited
C6-01 Duty Rating 1: Normal Duty
C6-02 Carrier Frequency Selection 3: 8.0 kHz
H2-03 Terminals P2 Function Selection (open-collector) 39: Watt Hour Pulse Output
2: CPU Power Active - Drive will 4
L2-01 Momentary Power Loss Operation Selection restart if power returns prior to
control power supply shut down.
L8-03 Overheat Pre-Alarm Operation Selection 4: Derated operation
2: Carrier frequency derating across
L8-38 Carrier Frequency Reduction
entire frequency range.

Table 4.12 Parameters Automatically Saved as Preferred (A2-01 to A2-16)

No. Parameter Name No. Parameter Name

b1-01 Frequency Reference Selection E1-03 V/f Pattern Selection
b1-02 Run Command Selection E1-04 Max Output Frequency (FMAX)
b1-04 Reverse Operation Selection E2-01 Motor Rated Current
C1-01 Acceleration Time 1 H3-11 Terminal A2 Gain Setting
Frequency Reference (Current)
C1-02 Deceleration Time 1 H3-12
Terminal A2 Input Bias
Momentary Power Loss Operation
C6-02 Carrier Frequency Selection L2-01
Selection
Overheat Pre-Alarm Operation
d2-01 Frequency Reference Upper Limit L8-03
Selection
d2-02 Frequency Reference Lower Limit o4-12 kWH Monitor Initial Value Selection

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 115
4.5 Application Presets

Table 4.13 Compressor Application: Parameters and Settings

No. Parameter Name Optimum Setting

A1-02 Control Method Selection 0: V/f Control
b1-04 Reverse Operation Selection 1: Reverse prohibited
C1-01 Acceleration Time 1 5.0 s
C1-02 Deceleration Time 1 5.0 s
C6-01 Duty Rating 0: Heavy Duty
E1-03 V/f Pattern Selection 0FH
L2-01 Momentary Power Loss Operation Selection 1: Enabled
L3-04 Stall Prevention Selection during Deceleration 1: Enabled

Table 4.14 Parameters Automatically Saved as Preferred (A2-01 to A2-16)

No. Parameter Name No. Parameter Name

b1-01 Frequency Reference Selection E1-03 V/f Pattern Selection
b1-02 Run Command Selection E1-07 Mid Output Frequency (FB)
b1-04 Reverse Operation Selection E1-08 Mid Output Frequency Voltage (VC)
C1-01 Acceleration Time 1 E2-01 Motor Rated Current
C1-02 Deceleration Time 1

Table 4.15 Crane Application (Hoist): Parameters and Settings

No. Parameter Name Optimum Setting

A1-02 Control Method Selection 2: Open Loop Vector Control
b1-01 Frequency Reference Selection 0: Operator
b6-01 Dwell Reference at Start 3.0 Hz
b6-02 Dwell Time at Start 0.3 s
C1-01 Acceleration Time 1 3.0 s
C1-02 Deceleration Time 1 3.0 s
C6-01 Duty Rating 0: Heavy Duty
C6-02 Carrier Frequency Selection 2: 5 kHz
d1-01 Frequency Reference 1 6.0 Hz
d1-02 Frequency Reference 2 30.0 Hz
d1-03 Frequency Reference 3 60.0 Hz
E1-03 V/f Pattern Selection 0FH
H2-02 Terminals P1 Function Selection (open-collector) 37: During frequency output
H2-03 Terminals P2 Function Selection (open-collector) 5: Frequency Detection 2 (FOUT)
L2-03 Momentary Power Loss Minimum Baseblock Time 0.3 s

116 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 4.5 Application Presets

No. Parameter Name Optimum Setting

Momentary Power Loss Voltage Recovery Ramp
L3-04 0: Disabled
Time
L4-01 Speed Agreement Detection Level 2.0 Hz
L4-02 Speed Agreement Detection Width 0.0 Hz
L6-01 Torque Detection Selection 1 8: UL3 at RUN -Fault
L6-02 Torque Detection Level 1 5%
L6-03 Torque Detection Time 1 0.5 s

Start-Up Programming &

L8-05 Input Phase Loss Protection Selection 1: Enabled
L8-07 Output Phase Loss Protection 1: Enabled
0: Derated when operating at 6 Hz or
L8-38 Carrier Frequency Reduction
less

Operation
L8-41 Current Alarm Selection 1: Enabled (alarm is output)

Note: A sequence to release the brake is needed when the multi-function output photocoupler P2-PC
closes. Refer to Hoist Application Preset Specifics on page 118 for more information.
Note: Perform Auto-Tuning after selecting the Hoist Application Preset.
Table 4.16 Parameters Automatically Saved as Preferred (A2-01 to A2-16) 4
No. Parameter Name No. Parameter Name
A1-02 Control Method Selection d1-02 Frequency Reference 2
b1-01 Frequency Reference Selection d1-03 Frequency Reference 3
b6-01 Dwell Reference at Start E1-08 Mid Output Frequency Voltage (VC)
Terminals MA, MB, and MC Function
b6-02 Dwell Time at Start H2-01
Selection
C1-01 Acceleration Time 1 L1-01 Motor Overload Protection Selection
C1-02 Deceleration Time 1 L4-01 Speed Agreement Detection Level
C6-02 Carrier Frequency Selection L6-02 Torque Detection Level 1
d1-01 Frequency Reference 1 L6-03 Torque Detection Time 1

Note: Read the instructions listed in Hoist Application Preset Specifics on page 118 when using Hoist
Application Preset.
Table 4.17 Crane Application (Travel): Parameters and Settings

No. Parameter Name Optimum Setting

A1-02 Control Mode 0: V/f Control
b1-01 Frequency Reference Selection 0: Operator
C1-01 Acceleration Time 1 3.0 s
C1-02 Deceleration Time 1 3.0 s
C6-01 Duty Cycle 0: Heavy Duty
C6-02 Carrier Frequency Selection 2: 5 kHz

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 117
4.5 Application Presets

No. Parameter Name Optimum Setting

d1-01 Frequency Reference 1 6.0 Hz
d1-02 Frequency Reference 2 30.0 Hz
d1-03 Frequency Reference 3 60.0 Hz
H1-05 Multi-Function Digital Input Terminal S5 Function 3: Multi-Step Speed 1
H1-06 Multi-Function Digital Input Terminal S6 Function 4: Multi-Step Speed 2
H2-02 Terminals P1 Function Selection (open-collector) 37: During frequency output
L3-04 Stall Prevention Selection during Decel 0: Disabled
L8-05 Input Phase Loss Protection Selection 1: Enabled
L8-07 Output Phase Loss Protection 1: Triggered when a single phase is lost
L8-38 Carrier Frequency Reduction 1: Always derated
L8-41 Current Alarm Selection 1: Enabled (alarm output)

Table 4.18 Parameters Automatically Saved as Preferred (A2-01 to A2-16)

No. Parameter Name No. Parameter Name

b1-01 Frequency Reference Selection d1-03 Frequency Reference 3
C1-01 Acceleration Time 1 E2-01 Motor Rated Current
Multi-Function Digital Input Terminal
C1-02 Deceleration Time 1 H1-05
S5 Function
Multi-Function Digital Input Terminal
C6-02 Carrier Frequency Selection H1-06
S6 Function
Terminals MA, MB, and MC Function
d1-01 Frequency Reference 1 H2-01
Selection
d1-02 Frequency Reference 2 L1-01 Motor Overload Protection Selection

Note: A sequence to release the brake is needed when the multi-function output photocoupler P2-PC
closes. Hoist Application Preset Specifics on page 118 for more information.

■ Hoist Application Preset Specifics

This section lists some important points when using the Hoist Application Preset (A1-06 =
6).
Conditions for Opening and Closing the Holding Brake
Use an output signal as described below to operate the holding brake in a hoist application.
Make sure that frequency detection is set so that it does not operate during baseblock (L4-07
= “0”). Even when an external baseblock command is present, the output frequency will rise
when a run command is entered. If frequency detection were to be enabled during baseblock,
(i.e., L4-07 = 1) then the brake would be improperly released. To activate and release the
brake using the multi-function output terminals P1-PC, program the drive as shown in the
table below:

118 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 4.5 Application Presets

Brake Open/Close Brake Activation Level Control Mode

OLV for
Function Parameter Signal Parameter V/f OLV
PM
Frequency L4-07 = 0 Frequency Detection Level L4-01 = 1.0 to 3.0 Hz <1>
O O -
Detection 2 H2-02 = 5 Frequency Detection Width L4-02 = 0.0 to 0.5 Hz <2>

<1> This setting range is available when using OLV Control. In V/f Control, set the level as the motor rated slip
frequency pulse 0.5 Hz. Not enough motor torque will be created if this value is set too low, and the load may tend

Start-Up Programming &

to slip. Make sure this value greater than the minimum output frequency and greater than the value of L4-02 as
shown in the diagram below. If this value is set too high, there may be a jolt at start.
<2> Adjust Hysteresis for Frequency Detection 2 by changing the frequency detection width (L4-02) between 0.0 and
0.5 Hz. If the load slips during stop, make incremental changes of 0.1 Hz until the load no longer slips.

Operation
L4-01
L4-02
Output
Time
Frequency

Frequency ON OFF
4
Detection 2

Sequence Circuit Design for Opening and Closing the Holding Brake
Design the braking sequence as follows:
The brake should release when terminal P2-PC closes in response to the run conditions on
the sequence side.
When a fault signal is output, the brake should close. When an up or down command is
entered, the brake should release.
Figure 4.10

Drive
24 V
Fault Contact Holding brake
MA
auxilary relay coil
UP S1
MB Safety UP
㧔Forward㧕 BR
Circuit
DOWN MC DOWN
S2
㧔Reverse㧕
BR
High speed S6 Frequency Detect 2
㧔Multi-step speed 2) P2 ONBrake energized
Low speed 㧔DC 30V 1A TCVKPI㧕
SC
PC

Figure 4.10 Holding Brake Circuit Design

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 119
4.5 Application Presets

Timechart for Opening and Closing the Holding Brake

A sequence to open and close the holding brake appears in the diagram below.
When changing the speed using an analog signal, make sure that the source of the frequency
reference is assigned to the control circuit terminals (b1-01 = 1).
Figure 4.11

Drive
24 V
Fault Contact Holding brake
MA
auxilary relay coil
UP S1
MB Safety UP
㧔Forward㧕 BR
Circuit
DOWN MC DOWN
S2
㧔Reverse㧕
BR
High speed S6 Frequency Detect 2
㧔Multi-step speed 2) P2 ONBrake energized
Low speed 㧔DC 30V 1A TCVKPI㧕
SC
PC

Figure 4.11 Holding Brake Timechart

◆ User Parameters: A2-01 to A2-32

The user can select 32 parameters and set them to parameters A2-01 through A2-32 to save
time scrolling through the parameter menu. The list of User Parameters can also track the
most recently edited settings and save those parameters to this list.

No. Parameter Name Setting range Default

A2-01 to A2-32 User Parameters, 1 to 32 b1-01 to o2-08 <1>

<1> Default setting value is dependent on parameter A1-06, Application Selection.

■ Detailed Description
To save specific parameters to A2-01 to A2-32, first set the access level to allow access to all
parameters (A1-02 = “2”). After selecting the parameters to be saved to A2-01 through A2-
32, set the access level to allow access only to the selected list of User Parameters. Set A1-
01 to “1” to restrict access so users can only set and reference the specific parameters saved
as User Parameters.

◆ User Parameter Automatic Selection: A2-33

A2-33 determines whether parameters that have been edited are saved to the User
Parameters (A2-17 to A2-32) for quick, easy access.

120 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 4.5 Application Presets

No. Parameter Name Setting range Default

0: Do not save history of recently
viewed parameters.
A2-33 User Parameter Automatic Selection 0, 1
1: Save history of recently viewed
parameters.

■ Detailed Description
0: Do not save history of recently viewed parameters.

Start-Up Programming &

To manually select the parameters listed in the Preferred Parameter group, set A2-33 to “0”.
1: Save history of recently viewed parameters.
By setting A2-33 to 1, all parameters that were recently edited will be saved to A2-17

Operation
through A2-32. A total of 16 parameters are saved in order, with the most recently edited
parameter set to A2-17.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 121
4.6 Basic Drive Setup Adjustments

4.6 Basic Drive Setup Adjustments

This section explains the basic settings required for initial drive operation. Checking these
basic parameter settings during start-up will help to ensure a successful drive start-up.
If more information is required for parameters not listed in this section, Refer to Parameter
List on page 309 as required for a complete listing of drive parameters.

◆ Control Mode Selection: A1-02

■ Available Control Modes
Three motor control modes are available. Select the control mode that best suits the
application in which the drive will be used.

Control Mode Parameter Main Applications

• General variable speed applications, particularly useful for
A1-02 = 0 running multiple motors from a single drive
V/f Control
(default) • When replacing a drive in which parameter settings are
unknown.
• General variable speed applications
Open Loop Vector Control A1-02 = 2
• Applications requiring high precision, high speed control.
Variable torque applications employing permanent magnet motors
PM Open Loop Vector Control A1-02 = 5
and energy savings.

◆ Initialize Parameter Values: A1-03

Parameter A1-03 (Initialize Parameters) resets all parameters to the original default values.
Note: Save all changed parameter settings by setting o2-03=”1” before initializing the drive. Your
settings will be lost if a 2-wire or 3-wire initialization using 2220, or 3330 if performed without
first saving user parameters. Refer to Backing Up Parameter Values: o2-03 on page 164.

■ Different Methods of Drive initialization

1110: Resets all parameters to user-defined default values
A user-initialization resets all parameters to a user-defined set of default values previously
saved to the drive. Set parameter o2-03 to “2” to clear those values.
Note: Set o2-03 to “1” to save the current parameter settings and changes for a “user-initialization.”
After saving all parameter setting changes, parameter o2-03 automatically returns to 0. Refer to
Verifying Parameter Settings and Backing Up Changes on page 163.
2220: 2-Wire Initialization
Returns all parameters to factory default values for 2-wire control.

122 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 4.6 Basic Drive Setup Adjustments

3330: 3-Wire Initialization

Returns all parameters to factory default values for 3-wire control.
1110: User Initialization
Returns all parameters to backed-up values stored at the time the user set o2-03 = 1 and
pressed enter to back-up parameter settings.
5550: Uploads Parameter Data from the Removable Control Circuit Terminal Board
Replacing either the removable control circuit terminal board or the drive and applying main

Start-Up Programming &

power may result in an oPE04 fault. If parameter setting data in the removable control circuit
terminal board is correct, set A1-03 to “5550” to upload the data to the drive.
Note: Refer to Run Command Input Selection: b1-02 on page 127, for more information on a 2-wire
and 3-wire sequence.
Note: Initializing the drive for 2-wire sequence (A1-03 = 2220) returns all drive parameters to factory

Operation
settings. Back up all parameters in the event of accidental initialization. the data with 2-wire
sequence returns all the set parameters to the factory settings. Refer to Backing Up Parameter
Values: o2-03 on page 164.

◆ Application Presets: A1-06 4

The drive features application presets to facilitate the set up of commonly used applications
such as a water supply pump, conveyor, exhaust fan, HVAC fan, compressor, hoist, and
crane. Selecting one of these presets automatically sets the required parameters to the
optimum values and changes the appropriate I/O terminal settings for that specific
application. Refer to Application Presets on page 111
Verify all I/O signals and external sequences before operating the motor. Refer to Hoist
Application Preset Specifics on page 118 when selecting a hoist application.
Users are able to make further adjustments to these settings using the Setup Mode.

No. Parameter Name Setting Range Default

0: General-purpose (A2 parameters are not affected)
1: Water supply pump
2: Conveyor
3: Exhaust fan 0
A1-06 Appilcaton Presets
4: HVAC fan <1>
5: Air compressor
6: Hoist
7: Crane (hoist, traverse)

<1> All general-purpose parameters are accessible when A1-06 = 0.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 123
4.6 Basic Drive Setup Adjustments

◆ DWEZ Function Selection: A1-07

DriveWorksEZ is an independent software package that can be used to operate and monitor
the drive with a 2 ms scan. It is fully compatible with all types of serial communication
software available on the market.
Setting A1-07 to “1” allows the drive to connect to the DriveWorksEZ software package.
When using DriveWorksEZ, be sure to set one of the multi-function terminal inputs for
DrivesWorksEZ (H1- = “9F”). This drive is ready to communicate with the software
when the terminal is open. Set A1-07 to “0” when DriveWorksEZ is not used.
If DriveWorksEZ assigned functions to any multi-function output terminals, those functions
stay set after disabling or disconnecting DriveWorksEZ.

No. Parameter Name Setting range Default

0: Disabled
1: Enabled
A1-07 DriveWorksEZ Function Selection 0
2: Terminal input switch (requires
that H1-XX = 9F)

◆ Frequency Reference Source: b1-01

This section explains how to assign the frequency reference. Parameters b1-01 and b1-02
can be used to select the source of the run command and the frequency reference
independently, e.g., set the reference from the operator and set the run command from the
terminals.
■ Frequency Reference from the LED Operator: b1-01 = 0
When b1-01 = 0 the frequency reference will be provided by the LED operator. Refer to The
Drive and Programming Modes on page 97 for information on how to set the frequency
reference.
■ Frequency Reference from the Analog Input Terminal: b1-01 = 1
When b1-01 = 1, analog inputs A1 and A2 provide the frequency reference.
Note: Set H3-02 (Terminal A1 Function Selection) to “0” to configure Terminal A1 for the main
analog frequency reference.
Using a Single Analog Signal (V or I) as the Frequency Reference
Control Circuit Terminal A1 (Voltage Input):
When entering the main frequency reference with a voltage signal, use the voltage input set
up in control circuit terminal A1.

124 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 4.6 Basic Drive Setup Adjustments

Figure 4.12

Drive

㧗V (+10.5 V㧘20 mA)

0 to 10 V
2 kΩ A1 Main Frequency Reference
(voltage input)
A2 Auxiliary Frequency Reference
(voltage/current input)
AC Frequency Reference
Common

Start-Up Programming &

Figure 4.12 Voltage Input for the Main Frequency Reference
Control Circuit Terminal A2 (Voltage/Current Input):
Use control circuit Terminal A2 when supplying the frequency reference with a current
signal between 4 to 20 mA. Use control circuit Terminal A1 for supplying a voltage

Operation
reference.
• Set the signal level for analog input A2 to current input (H3-09 = “2” for 4 to 20 mA, H3-
09 = “3” for 0 to 20 mA).
• Set the function for analog input A2 to frequency reference (H3-10 = “0”) to command
terminal A2 to be a frequency reference.
4
• Set DIP switch S1 to the I position for a current signal input.
Figure 4.13

DIP switch S1
Drive
V I

㧗V (+10.5 V, 20 mA)

A1 Main Frequency Reference

(voltage input)
(0) 4 - 20 mA input
A2 Main Frequency Reference
(current input)
AC Frequency Reference
Common

Figure 4.13 Current Input for the Main Speed Reference

Switching between Main/Auxiliary Frequency References
To configure the frequency reference to switch between analog input A1 and A2 (main/aux
frequency switch), use the following setup:
1. Set the frequency reference source to terminals (b1-01 = “1”).
2. Set one of the digital inputs to auxiliary reference 1, H1- = “3” (preset for terminal S5).
3. Set input signal type of terminal A2 using dip switch S1 and parameter H3-09.
4. Set the function of analog input A2 to Auxiliary frequency (H3-10 = “3”).

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 125
4.6 Basic Drive Setup Adjustments

When the digital input assigned in step 2 is off, terminal A1 is the frequency reference input.
If it is closed, the A2 input value becomes the frequency reference. The active acceleration /
deceleration times are used for the change-over between the values
Figure 4.14

Drive

V (+10.5 V, 20 mA)

2 kohm A1 Main Frequency Reference

(voltage input)

2 kohm A2 Aux Frequency Reference 1

(voltage input)
AC Frequency Reference Common

S5 Multi-Function Digital Input

SC Digital Input Common

Figure 4.14 Switching between Main/Auxiliary Frequency References

■ Pulse Train Input: b1-01 = 4

Setting b1-04 to 4 programs the drive so that the frequency reference is provided by the
pulse train control circuit input terminal RP.
Configuring the Drive for Pulse Train Frequency Reference Input
Setting up the Pulse Input (RP) as frequency reference input:
1. Set the reference source to pulse input (b1-01 = “4”)
2. Set the pulse train input to be the frequency reference by programming parameter H6-01 =
“0” and programming the pulse train input gain to 100% (H6-03 = “100”)
3. Set the pulse input scaling (H6-02) to the input frequency value which is equal to the max.
frequency reference value.
4. Apply a pulse signal to the input and check that the reference value is the desired value.
5. Readjust the pulse input gain and bias if necessary.
Note: 1. If the frequency display reaches the maximum desired frequency before the maximum pulse reference
signal is applied, increase the pulse train input scaling value (increase H6-02).
2. If the frequency display never reaches the desired maximum with the maximum pulse reference signal
applied, decrease the pulse train input scaling value (reduce H6-02)
The pulse input has the following specifications. Ensure the pulse signal meets these
specifications:

Pulse Train Input Specifications

Response Frequency 0.5 to 32 kHz
Duty Cycle 30 to 70%
High Level Voltage 3.5 to 13.2 V
Low Level Voltage 0.0 to 0.8 V

126 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 4.6 Basic Drive Setup Adjustments

Pulse Train Input Specifications

Input Impedance 3 kΩ

◆ Run Command Input Selection: b1-02

This section explains how to assign the run command input.
Parameters b1-01 and b1-02 can be used to select the source of the run command and the
frequency reference independently, e.g. set the reference from the operator and set the run

Start-Up Programming &

command from the terminals.
WARNING! Sudden Movement Hazard. When the run command is given by turning on the power to the
drive, the motor will begin rotating as soon as the drive is powered up. Be sure to take proper precautions if
using this setting. Ensure the area around the motor is safe. Failure to comply could result in death or

Operation
serious injury.

■ Run the Drive at 6 Hz using the Digital LED Operator: b1-02 = 0

To assign the run command to the operator panel, set parameter b1-01 to “0”. This will set
up the drive to acknowledge the run command through the LED operator. Initialize the run
command using the Run and Stop keys. Upon power up, the drive uses parameter b1-02 to 4
determine the run command location.
The following procedure indicates how to start and stop the drive through the LED operator
after parameter b1-02 has been set to 0.
Note: When b1-02 (Run Command Selection) is not set to 0 (operator), press to set LOCAL.

Step Display/Result

1. Turn on the power to the drive. The initial display appears. ⇒

2. Set the frequency reference to F6.00 (6 Hz).

Note: Refer to Drive Mode Details on page 100 for instructions on ⇒
how to set the frequency reference.

3. Press the RUN key to start the motor. ⇒

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 127
4.6 Basic Drive Setup Adjustments

Step Display/Result

4. The motor should accelerate up to 6 Hz while the RUN light is on. ⇒

STOP

off on

5. Press the STOP key to stop the motor. The RUN light will flash ⇒
until the motor comes to a complete stop. flashing off

■ Run the Drive using Digital Input Terminals: b1-02 = 1

This setting uses the digital input terminals to enter the run command. The factory setting is
a 2-wire sequence.
Using a 2-Wire Sequence

Digital Input Terminals ON OFF

S1 Forward Run Stop
S2 Reverse Run Stop
Figure 4.15

Drive
Forward Run
S1

Reverse Run
S2

SC Digital Input Common

Figure 4.15 Example Wiring Diagram for 2-Wire Sequence

Using a 3-Wire Sequence
When H1-05 (Multi-Function Digital Input Terminal S5 Function Selection) = 0, the
functions of terminals S1 and S2 are set to 3-wire sequence, and the multi-function input
terminal becomes forward/reverse run command terminal.

128 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 4.6 Basic Drive Setup Adjustments

Figure 4.16

Stop Switch Run Switch Drive

(N.C.) (N.O.)
S1
Run Command
(runs when open)
S2
Stop Command
(stops when closed)
S5
FWD/REV Command
(multi-function input)*
SC
Digital Input Common

Start-Up Programming &

Figure 4.16 Example Wiring Diagram for 3-Wire Sequence Using Terminal S5
Note: When terminal S5 is open, the motor rotates forward. When closed, the motor rotates in reverse.

WARNING! When 3-Wire sequence is used, set the drive to 3-Wire sequence before wiring the control
terminals and ensure parameter b1-17 is set to 0 (drive does not accept a run command at power up

Operation
(default)). If the drive is wired for 3-Wire sequence but set up for 2-Wire sequence (default) and if parameter
b1-17 is set to 1 (drive accepts a Run command at power up), the motor will rotate in reverse direction at
power up of the drive and may cause injury.

Note: Refer to Parameter List on page 309 for a list of digital input functions. After performing a 3-
wire initialization (A1-03 = “3”), the drive will automatically assign the forward/reverse
command to terminal S5. 4
CAUTION! The motor will begin rotating as soon as the power is switched on. Proper precautions must be
taken to ensure that the area around the motor is safe prior to powering up the drive. Failure to do so may
result in minor or moderate injury.

Note: Run by Turning on/off the Power Supply. For safety reasons, the drive is initially set up not to
accept a run command at power up (b1-17 = "0"). If a run command is issued at power up, the
RUN indicator LED will flash quickly. To change this and have the run command issued by the
drive, change parameter b1-17 to 1

◆ Stopping Method Selection: b1-03

When a Stop command is issued, the drive stops the motor using one of four possible
methods.
■ Ramp to Stop: b1-03 = 0
When b1-03 = 0, the motor will decelerate to a stop when a stop command is entered. The
deceleration time is set by C1-02 (Deceleration Time 1). Refer to Acceleration/
Deceleration: C1-01 to C1-11 on page 132.
When the output frequency falls below the DC Injection braking start frequency (b2-01)
during deceleration, the DC Injection braking current (b2-02) will be activated for the
specified DC Injection time at stop (b2-04).

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 129
4.6 Basic Drive Setup Adjustments

Figure 4.17

Run Command
ON OFF

Output Frequency

Decelerates according to the

specified deceleration time
Zero Speed Level
(b2-01)

Decel Time
(C1-02, etc.)
DC Injection
Current (b2-02)
DC Injection Braking
DC Braking Time at Stop (b2-04)

Figure 4.17 Ramp to Stop

Note: Parameter b2-04 is not available if using PM Open Loop Vector. Instead, set the Short Circuit
Braking time to b2-13.

■ Coast to Stop: b1-03 = 1

When the run command is removed, the drive will shut off its output and the motor will
coast (uncontrolled deceleration). The motor will coast to a stop at the rate determined by the
load inertia.
Figure 4.18

Run Command
ON OFF

Output Voltage

Drive output voltage interrupted

Motor Rotations

Figure 4.18 Coast to Stop

Note: 1. After entering a stop command, the drive will not accept another run command until the time set to L2-
03 (Minimum Baseblock Time) passes.
2. Do not enter another run command until the motor comes to a complete stop. If a run command must be
entered before the motor has fully stopped, use DC Injection or Speed Search functions to slow the
motor or catch the motor before restarting. For details refer to V1000 Technical Manual.

■ DC Injection Braking to Stop: b1-03 = 2

DC Injection Braking stops a coasting motor without without regenerative operation. When
the run command is removed, the drive will baseblock (turn off its output) for the minimum

130 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 4.6 Basic Drive Setup Adjustments

baseblock time (L2-03). Once the minimum baseblock time has expired, the drive will inject
DC current into the motor windings to lock the motor shaft. The stopping time will be
reduced as compared to coast to stop. The level of DC Injection current is set by parameter
b2-02 (default = 50%). The time for DC Injection Braking is determined by the value set to
b2-04 and by the output frequency at the time the run command is removed.
Note: DC Injection braking cannot be selected as a stopping method in PM Open Loop Vector Control.
Figure 4.19

Run Command
ON OFF

Output Frequency

Start-Up Programming &

Minimum Baseblock Time (L2-03)

DC Injection Braking

DC Injection Braking DC Braking

Time at Stop Current (b2-02)
Motor Speed (b2-04)*

Operation
DC Injection Braking Time

b2-04˜10

b2-04
4
Output frequency when
stop command was entered

10% 100%
(Max Output Frequency)

Figure 4.19 DC Injection Braking Stop

*See Figure 4.18
Note: Extend baseblock time (L2-03) if overcurrent (OC) occurs on stop command input.

■ Coast to Stop with Timer: Ignoring a Run Command Input within the
Deceleration Time: b1-03 = 3
When b1-03 = 3, a stop command interrupts drive output and the motor coasts to stop. The
drive will not accept the next run command until time “t” has passed. Time “t” is determined
by the output frequency at the moment the stop command was entered and the deceleration
time set to the drive according to Figure 4.20.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 131
4.6 Basic Drive Setup Adjustments

Figure 4.20

Run Command
ON OFF ON OFF ON

Output Frequency

Drive output voltage interrupted

Operation Wait Time t

Operation wait time t

Deceleration time
(C1-02, etc.)

Minimum
Output frequency when
Baseblock Time
stop command was entered
㧔L2-03㧕

Minimum Output Frequency 100㧑

(Max Output Frequency)

Figure 4.20 Coast to Stop with Timer

◆ Acceleration/Deceleration: C1-01 to C1-11

C1-01 (Acceleration Time 1) sets the time to accelerate from 0 to the maximum output
frequency (E1-04). C1-02 (Deceleration Time 1) sets the time to decelerate from maximum
output frequency to 0.

Setting
No. Parameter Name Description Range Default

C1-01 Sets the time to accelerate from 0 to 100% (maximum

Acceleration Time 1 0.0 to
<1> output frequency).
6000.0 10.0 s
C1-02 Sets the time to decelerate from 100% (maximum <2>
Deceleration Time 1
<1> output frequency) to 0%.
Sets the setting resolution of C1-01 toC1-09.
Accel/Decel Time
C1-10 0: 0.01 s (0.00 to 600.00 s) 0, 1 1
Setting Units
1: 0.1 s (0.0 to 6000.0 s)

<1> The parameter can be changed during run.

<2> The setting range for the acceleration and deceleration times is determined by C1-10 (Accel/Decel Time Setting
Units). For example, if the time is set in units of 0.01 s (C1-10 = 0), the setting range becomes 0.00 to 600.00 s

WARNING! Sudden Movement Hazard. Rapid deceleration may cause the drive to fault on an overvoltage
condition, resulting in death or serious injury due to an uncontrolled motor state. Set an acceptable
deceleration time in parameter C1-09 when using the Fast-stop feature.

■ Accel/Decel Time Setting Units

Set the units for the acceleration and deceleration times using parameter C1-10 (default = 1).

132 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 4.6 Basic Drive Setup Adjustments

Setting Description
0 Time is set in units of 0.01 s, making the setting range 0.00 to 600.00 seconds.
1 Time is set in units of 0.1 s, making the setting range 0.0 to 6000.0 seconds.

■ Switching Accel/Decel Times with Digital Input Terminals

Up to four different acceleration / deceleration times can be selected using any two digital
input terminals S1 through S7.

Start-Up Programming &

Program two parameters H1-01 through H1-07 to “07” (Accel/Decel Time 1) and “1A”
(Accel/Decel Time 2). The combination of these two inputs activates the acceleration/
deceleration times as shown below. As the contacts of the terminals open and close, the
following acceleration and deceleration time combinations are possible:

Operation
Accel/Decel Time 1 Accel/Decel Time 2
H1- =7 H1- = 1A Acceleration Time Deceleration Time

Open (not selected) Open (not selected) C1-01 C1-02

Closed Open (not selected) C1-03 C1-04 4
Open (not selected) Closed C1-05 C1-06
Closed Closed C1-07 C1-08

■ Automatically Switching Acceleration/Deceleration Times

The drive can automatically switch between acceleration and deceleration times.
When the output frequency reaches the value set to C1-11, the drive will switch acceleration
and deceleration times as shown in the figure below. Setting C1-11 to 0.0 Hz disables this
function.
Figure 4.21

Output Frequency

C1-11
Accel/Decel Time
Switch Frequency

C1-07 C1-01 C1-02 C1-08

setting setting setting setting
When the output frequency ҈ C1-11, drive uses Accel/Decel Time 1 (C1-01, -02)
When the output frequency < C1-11, drive uses Accel/Decel Time 2 (C1-07, -08)
Figure 4.21 Accel/Decel Time Switching Frequency

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 133
4.6 Basic Drive Setup Adjustments

■ Using S-Curve Characteristics during Acceleration/Deceleration

Using S-curve characteristics to smooth acceleration and deceleration minimizes abrupt
shock to the load. Set S-curve characteristic time during acceleration/deceleration at start
and acceleration/deceleration at stop.
Note: 1. Setting S-curve characteristics will lengthen accel/decel times as follows:
Accel Time = Selected Accel Time + (C2-01 + C2-02)/2
Decel Time = Selected Decel Time + (C2-03 + C2-04)/2
2. Set longer S-curve times using PM Open Loop Vector Control.
Setting Example
Figure 4.22 illustrates S-curve characteristics switching between forward and reverse.
Figure 4.22

Forward Run
Command
Reverse Run
Command

C2-02 C2-04
C2-03
Output
Frequency
C2-01
C2-01 C2-04

C2-02 C2-03
Figure 4.22 S-Curve Characteristics

◆ Drive Duty Mode and Carrier Frequency Selection:

C6-01 and C6-02
■ Drive Duty Mode Selection: C6-01
The drive has two different duty modes from which to select based on the load
characteristics. The drive rated current, overload capacity, carrier frequency, and maximum
output frequency will change depending upon the duty mode selection. Use parameter C6-01
(Duty Cycle) to select Heavy Duty (HD) or Normal Duty (ND) for the application. The
factory setting is ND. Refer to Specifications on page 291 for details about the rated current.
HD and ND Mode Selections

Mode HD Rating ND Duty Rating

C6-01 0 1

134 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 4.6 Basic Drive Setup Adjustments

Mode HD Rating ND Duty Rating

Overload
150 % Overload
120 %
Rated Load
Rated Load 100 %
100 %
Characteristics

0 100 %

Start-Up Programming &

Motor Speed
0 Motor Speed 100 %

Use HD Rating is designed applications Use ND Rating for applications in which the
requiring a high overload tolerance with torque requirements drop along with the
Application
constant load torque. Such applications speed. Examples include fans or pumps where
include extruders, conveyors and cranes. a high overload tolerance is not required.

Operation
Overload capability 100% continuous, 150% of drive rated 100% continuous, 120% of drive rated current
(OL2) current for 60 s for 60 s
L3-02 Stall
Prevention during 150% 120%
Acceleration
L3-06 Stall
4
Prevention during 150% 120%
Run

Note: By selecting HD/ND motor parameters E2 and E4 are changed to values for the maximum
applicable motors.

■ Carrier Frequency Selection: C6-02

Fixed Carrier Frequencies
The carrier frequency can be set using parameter C6-02 as shown in table below.

Parameter Name Description Setting Range Default

1: 2.0 kHz
2: 5.0 kHz
3: 8.0 kHz
4: 10.0 kHz
5: 12.5 kHz
Carrier depends on
C6-02 6: 15.0 kHz 1 to F
frequency drive size
7: Swing PWM1
8: Swing PWM2
9: Swing PWM3
A: Swing PWM4
F: User defined (C6-03 to C6-05)

Note: Settings 7 through A for parameter C6-02 use a Swing PWM equivalent to a 2 kHz audible
noise. This function turns the motor noise into a less obtrusive white noise.
Note: The upper limit for the carrier frequency is determined by drive capacity.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 135
4.6 Basic Drive Setup Adjustments

Precautions when setting parameter C6-02:

Symptom Remedy
Speed and torque are unstable at low speeds.
Noise from the drive is affecting peripheral devices.
Lower the carrier frequency.
Excessive leakage current from the drive.
Wiring between the drive and motor is too long. <1>
Motor acoustic noise is too loud. Increase the carrier frequency or use Swing PWM.

<1> The carrier frequency may need to be lowered if the motor cable is too long. Refer to the table below.

Wiring Distance Up to 50 m Up to 100 m Greater than 100 m

C6-02 (Carrier Frequency Selection) 1 to A (15 kHz) 1 to 2, 7 to A (5 kHz) 1, 7 to A (2 kHz)

Note: When using PM Open Loop Vector control with long cable lengths, set the carrier freqency to 2
kHz (C6-02 = “1”). Use V/f control if the motor cable exceeds 100 m.
User Defined and Variable Carrier Frequency
Set parameter C6-02 to “F” to set carrier frequency values between fixed values.
In Open Loop Vector and PM motor control the desired value can be set in parameter C6-03.
In V/f control the carrier frequency can be set up to change linearly with the output
frequency. In this case the upper and lower limits for the carrier frequency and the carrier
frequency proportional gain (C6-03, C6-04, C6-05) have to be set up like shown
Figure 4.23.
Note: Set both C6-03 and C6-04 to the same value or set C6-05 to 0 to keep the carrier frequency at a
constant level. C6-03 sets the Carrier frequency upper limit.
Figure 4.23

Carrier Frequency

C6-03

Output Frequency
C6-04 × (C6-05) × K

Output Frequency
E1-04
Maximum Output Frequency
* The value of coefficient K is determined by the value of C6-03.
C6-03 ҈ 10.0 kHz㧦K=3
10.0 kHz > C6-03 ҈ 5.0 kHz㧦K=2
5.0 kHz > C6-03㧦K=1

Figure 4.23 Carrier Frequency Changes Relative to Output Frequency

Note: For Open Loop Vector Mode, A1-02 = 2 and OLV for PM the carrier frequency is fixed to a
value set by C6-02 or C6-03 if C6-02 is set to F (programmable).

136 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 4.6 Basic Drive Setup Adjustments

Carrier Frequency Setting Error (oPE11)

A carrier frequency setup error (oPE11) will occur when carrier frequency gain (C6-05) is
greater than 6 and C6-03 < C6-04.
Note: Refer to Troubleshooting without Fault Display on page 228 for information on operator errors
(oPE).

■ Carrrier Frequency and Drive Overload Current Level

With C6-01 set to 1, the carrier frequency setting defines drive output current level.

Start-Up Programming &

Table 4.19 Current Derating by Carrier Frequency Setting

Single-Phase 200 V Three-Phase 200 V Three-Phase 400 V

Carrier Output Carrier Output Carrier Output
Model Frequency Current Model Frequency Current Model Frequency Current
(Capacity) (Capacity) (Capacity)

Operation
(kHz) (A) (kHz) (A) (kHz) (A)

B 0001 2 1.2 2 0001 2 1.2

0.2 kW/ 10 0.8 0.2 kW/ 10 0.8
0.1 kW 15 0.6 0.1 kW 15 0.6

B 0002 2 1.9 2 0002 2 1.9 4 0001 2 1.2

4
0.4 kW/ 10 1.6 0.4 kW/ 10 1.6 0.4 kW/ 8 1.2
0.2 kW 15 1.3 0.2 kW 15 1.3 0.2 kW 15 0.7

B 0003 2 3.3 2 0004 2 3.3 4 0002 2 2.1

0.75 kW/0.4 10 3.0 0.75 kW/0.4 10 3.0 0.75 kW/0.4 8 1.8
kW 15 2.4 kW 15 2.4 kW 15 1.1

B 0006 2 6.0 4 0004 2 4.1

1.5 kW/0.75 10 5.0 1.5 kW/0.75 8 3.4
kW 15 4.0 kW 15 2.0

2 0006 2 6.0
1.1 kW/ 10 5.0
0.75W 15 4.0

2 0008 2 8.0
1.5 kW/ 8 6.9
1.1 kW 15 5.5

B 00010 2 9.6 2 0010 2 9.6 4 0005 2 5.4

2.2 kW/ 8 8.0 2.2 kW/ 8 8.0 2.2 kW/ 8 4.8
1.5W 15 6.4 1.5W 15 6.4 1.5W 15 2.9

B 0012 2 12.0 2 0012 2 12.0 4 0007 2 6.9

3.0 kW/ 8 11.0 3.0 kW/ 8 11.0 3.0 kW/ 8 5.5
2.2 kW 15 8.8 2.2 kW 15 8.8 2.2 kW 15 3.3

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 137
4.6 Basic Drive Setup Adjustments

Single-Phase 200 V Three-Phase 200 V Three-Phase 400 V

Carrier Output Carrier Output Carrier Output
Model Frequency Current Model Frequency Current Model Frequency Current
(Capacity) (Capacity) (Capacity)
(kHz) (A) (kHz) (A) (kHz) (A)

2 0018 2 17.5 4 0009 2 8.8

3.7 kW/ 8 14.0 3.7 kW/ 8 7.2
3.0W 15 11.2 3.0 kW 15 4.3

2 0020 2 19.6 4 0011 2 11.1

5.5 kW/ 8 17.5 5.5 kW/ 8 9.2
4.0 kW 15 14.0 4.0 kW 15 5.5

◆ Drive Input Voltage Setting: E1-01

Set E1-01 according to the power supply voltage. This setting serves as a base value for
certain drive protective functions.
NOTICE: Set drive input voltage (not motor voltage) in parameter E1-01 for proper function of the protective
features of the drive. Failure to comply could result in improper drive operation. Set parameter E1-01 to
match the input voltage of the drive.

Parameter Name Description Setting Range Default

Set to the nominal voltage of the incoming line. Sets
Input the maximum and base voltage used by preset V/f
200 V Class: 155 to 255
E1-01 Voltage patterns (E1-03), and adjusts the levels of drive 230 V
400 V Class: 310 to 510
Setting protective features (e.g., overvoltage, braking
resistor level, stall prevention, etc.).

■ Input Voltage Setting Value: E1-01

The input voltage level determines the overvoltage detection level and the operation level of
the braking transistor as shown in the table below.

(Approximate Values)
Setting Value Braking Voltage Level
Voltage of OV Transistor Desired AC for OV
E1-01 Detection Operation UV Detection Level Voltage Suppression,
Level during KEB
Level Stall Prevention
200 V 190 V
all settings 410 V 394 V 240 V 370 V
Class (single-phase=160 V)
400 V setting ≥ 400V 820 V 788 V 380 V 480 V 740 V
Class setting < 400V 740 V 708 V 350 V 440 V 660 V

Note: This data is for an internal dynamic braking resistor of 0.1 to 18.5 kW. For larger units, see
“Dynamic Braking Resistor Unit for VARISPEED-600 Series, TOBPC72060000”

138 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 4.6 Basic Drive Setup Adjustments

◆ V/f Pattern Selection: E1-03

Parameter E1-03 is only available when using V/f Control. It allows the user to set the
required V/f pattern and drive output voltage. When running a high-speed or special-purpose
motor, this function fine tunes the amount of torque required for the load. Select the V/f
pattern from 15 fixed V/f patterns or 1 user-programmable V/f pattern.

Setting

Start-Up Programming &

No. Parameter Name Description Default
Range
0 to E: Select from 15 preset V/f patterns.
E1-03 V/f Pattern Selection 0 to F F
F: Custom V/f pattern (allows use of E1-04 through E1-10).

■ Setting Instructions for Setting a V/f Pattern

Operation
1. Set the input voltage for the drive. Refer to Drive Input Voltage Setting: E1-01 on
page 138.
2. Select one of the two following V/f patterns:
• *Select one of the 15 preset V/f patterns (setting = 0 through E)
• **Select the Custom V/f pattern (setting = F) 4
3. In case of * the following parameters are automatically set.
In case of **, the following parameters are adjustable.
E1-04 (Max Output Frequency), E1-05 (Max Voltage), E1-06 (Base Frequency), E1-
07 (Mid Output Frequency), E1-08 (Mid Output Frequency Voltage), E1-09 (Min
Output Frequency), E1-10 (Min Output Frequency Voltage)
Figure 4.24

Output Voltage (V)

E1-05
E1-12

E1-13

E1-08

E1-10

E1-09 E1-07 E1-06 E1-11 E1-04

Frequency (Hz)

Figure 4.24 V/f Pattern

■ Selecting a Preset V/f Pattern

There are two types of V/f patterns: a method to select one of the 15 presets (set value: 0 to
E) and a method to select arbitraty V/f pattern (set value: F). Refer to Table 4.20.

No. Parameter Name No. Parameter Name

E1-04 Maximum Output Frequency (FMAX) E1-08 Mid Output Frequency Voltage (VC)
E1-05 Maximum Voltage (VMAX) E1-09 Minimum Output Frequency (FMIN)

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 139
4.6 Basic Drive Setup Adjustments

No. Parameter Name No. Parameter Name

E1-06 Base Frequency (FA) E1-10 Minimum Output Frequency Voltage (VMIN)
E1-07 Mid Output Frequency (FB)

Note: The default setting for the V/f pattern is for a custom V/f pattern (E1-03 = F).
Table 4.20 V/f Patterns

Setting Specification Characteristic Application

0 50 Hz
1 (F) 60 Hz For general purpose applications, torque
Constant torque remains constant regardless of speed
2 60 Hz (with 50 Hz base) changes.
3 72 Hz (with 60 Hz base)
4 50 Hz, Heavy Duty 3
5 50 Hz, Heavy Duty 2 For applications where torque changes with
Reduced or
the speed like fans, pumps, and others that
6 60 Hz, Heavy Duty 3 variable torque
require reduced torque relative to the load.
7 60 Hz, Heavy Duty 2
8 50 Hz, mid starting torque

9 50 Hz, high starting torque • High starting should be selected only when:
• Wiring between the drive and motor exceeds
150 m
High starting
A 60 Hz, mid starting torque • Large amount of starting torque is required
torque
• AC reactor is installed
• motor exceeds the largest motor
recommended for that drive used
B 60 Hz, high starting torque

C 90 Hz (with 60 Hz base)

When operating at speeds greater than 60 Hz

D 120 Hz (with 60 Hz base) Constant output motor requires constant voltage. Above 60
Hz, motor operates in constant power range.

E 180 Hz (with 60 Hz base)

■ V/f Pattern Characteristics

These graphs apply to 200 V class drives; double the values for 400 V class drives.
• Constant Torque Characteristics, Settings 0 through 3

Setting = 0 50 Hz Setting = 1 60 Hz Setting = 2 60 Hz Setting = 3 72 Hz

140 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 4.6 Basic Drive Setup Adjustments

200 200 200 200

Voltage (V)

Voltage (V)
Voltage (V)
Voltage (V)
16 16 16 16
12 12 12 12
0 1.3 2.5 50 0 1.5 3 60 0 1.5 3 50 60 0 1.5 3 60 72
Frequency (Hz) Frequency (Hz) Frequency (Hz) Frequency (Hz)

Start-Up Programming &

• Reduced Torque Characteristics, Settings 4 through 7

Setting = 4 50 Hz Setting = 5 50 Hz Setting = 6 60 Hz Setting = 7 60 Hz

Operation
200 200 200 200

Voltage (V)
Voltage (V)

Voltage (V)
Voltage (V)

35
50
35
50 4
9 9
8 8
0 1.3 25 50 0 1.3 25 50 0 1.5 30 60 0 1.5 30 60
Frequency (Hz) Frequency (Hz) Frequency (Hz) Frequency (Hz)

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 141
4.6 Basic Drive Setup Adjustments

• High Starting Torque Characteristics, Settings 8 through B

Setting = 8 50 Hz Setting = 9 50 Hz Setting = A 60 Hz Setting = B 60 Hz

200 200 200 200

Voltage (V)

Voltage (V)

Voltage (V)
Voltage (V)
24 24
19 19
13 15
12 12
0 1.3 2.5 50 0 1.3 2.5 50 0 1.5 3 60 0 1.5 3 60
Frequency (Hz) Frequency (Hz) Frequency (Hz) Frequency (Hz)

• Constant Output Characteristics, Settings C through F

Setting = C 90 Hz Setting = D 120 Hz Setting = E 180 Hz

200 200 200

Voltage (V)
Voltage (V)

Voltage (V)

16 16 16
12 12 12
0 1.5 3 60 90 0 1.5 3 60 120 0 1.5 3 60 180
Frequency (Hz) Frequency (Hz) Frequency (Hz)

Note: Setting an improper V/f pattern may result in reduced motor torque or increased current (due to
over excitation).

◆ Motor Parameters: E2-01 through E2-12

(Manually Entering Parameter Settings)
In Open Loop Vector Control, motor parameters are set automatically during the Auto-
Tuning process. Manually set motor parameters if Auto-Tuning cannot be performed. Refer
to Auto-Tuning on page 153 for more information. Refer to E: Motor Parameters on
page 330 fir a list of motor parameters E2-01 to E2-12.
■ Setting Motor Parameters Manually
The following table provides instructions on how to set motor parameters. Refer to the motor
data sheet for the correct motor data.

142 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 4.6 Basic Drive Setup Adjustments

No. Parameter Name Setting Method

E2-01 Motor Rated Current Sets the motor nameplate full load current in amperes (A).
Calculate and set the motor rated slip based on the rated speed described on
the motor nameplate.
E2-02 Motor Rated Slip
Motor rated slip = Motor rated frequency [Hz] - Rated speed [r/min] x No. of
motor poles / 120.
Set motor no-load current at rated voltage and rated frequency.
Contact the motor manufacturer to get the no-load current. This information is

Start-Up Programming &

E2-03 Motor No-Load Current
not usually written on the motor nameplate.
The default no-load current is for a Yaskawa 4-pole motor.
Displayed only when OLV control mode is selected. Set the number of motor
E2-04 Number of Motor Poles
poles described on the motor nameplate.
This value is automatically set during Auto-tuning. When regular Auto-

Operation
Tuning is not possible, contact the motor manufacturer to find out the
resistance between lines (T-lead to T-lead). If using the Motor Test Report,
Motor Line-to-Line
E2-05 calculate resistance between lines as follows:
Resistance
E-Type Insulation: Test Report value for line resistance at 75 °C at 0.92 ohms
B-Type Insulation: Test Report value for line resistance at 75 °C at 0.92 ohms
F-Type Insulation: Test Report value for line resistance at 115 °C at 0.87 ohms 4
Set the amount of voltage drop due to motor leakage inductance at base
frequency and motor rated current.This value should be set when using a high-
Motor Leakage
E2-06 speed motor or another type of motor that has a relatively small amount of
Inductance
inductance. Contact the motor manufacturer to get the motor leakage
inductance, as this information is not usually written on the motor nameplate.
E2-07 Motor Iron-Core
This value is automatically set during rotational Auto-Tuning.
<1> Saturation Coefficient 1
E2-08 Motor Iron-Core
This value is automatically set during rotational Auto-Tuning.
<1> Saturation Coefficient 2
Displayed only when using Open Loop Vector Control. It is not necessary to
set this parameter, but it may require adjustment under the following
circumstances:
E2-09 Motor Mechanical Loss Large amount of torque loss relative to motor bearings
Fan and pump type applications with a large amount of torque loss
The amount of mechanical loss will be reflected in the amount of torque
compensation.
Motor Iron Loss for Displayed only when using V/f Control. Increase the motor iron loss in watts
E2-10
Torque Compensation in order to increase the accuracy of torque compensation.
Sets the motor rated power in kilowatts (kW). This value is automatically set
E2-11 Motor Rated Output
during Auto-Tuning in units of 0.01.
E2-12 Motor Iron-Core Set to the motor iron saturation coefficient at 130% of magnetic flux. This
<1> Saturation Coefficient 3 value is automatically set during rotational Auto-Tuning.

<1> Parameters E2-07 through E2-08 and E2-12 may be difficult to set manually. If Auto-Tuning is not possible,
simply leave these settings at the default values.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 143
4.6 Basic Drive Setup Adjustments

◆ Digital Outputs H2-01 to H2-03

Parameters H2-01, H2-02 and H2-03 assign functions to digital output terminals MA, MB,
MC, P1, and P2. Set these parameters as required by the application. Default values are
listed below.
NOTICE: Do not assign a function that repeats ON/OFF frequently to terminals MA and MB. Failure to
comply will reduce the relay contact lifetime. The expected number of relay contact switching times is
normally 200,000 times (current 1 A, resistance load).

No. Parameter Name Default

H2-01 Terminal MA, MB and MC Function Selection (relay) E: Fault
H2-02 Terminal P1 Function Selection (open-collector) 0: During Run
H2-03 Terminal P2 Function Selection (open-collector) 2: Speed Agree 1

Note: The setting range for H2-01 through H2-03 is 0 to 14D. Refer to Parameter List on page 309 for
more information.
Figure 4.25

Multi-Function Contact Outputs

250 Vac, 10 mA - 1 A
30 Vdc, 10 mA - 1 A
(standard default setting)

MA Fault
MB
MC Fault

Multi-Function Open-collector Outputs

48 Vdc, 50 mA or less
(standard default setting)

P1 During Run (Open-collector 1)

P2 Speed Agree (Open-collector 1)

PC Open-collector Common

Figure 4.25 Digital Output Connection Diagram

◆ Analog Outputs: H4-01 to H4-03

Group U parameters can be used to observe the drive status (operating conditions) through
the LED operator. Analog outputs corresponding to these monitors can be obtained on
analog output terminal AM or Fm when programmed with parameter group H4. Some
Group U monitors are not available as analog outputs.

144 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 4.6 Basic Drive Setup Adjustments

No. Parameter Name Description

Select the data to output through multi-function analog output terminal AM.
Multi-Function Analog 1 Set the desired monitor parameter to the digits available in U†-††. For
H4-01 (Terminal AM Monitor example, enter “103” for U1-03.
Selection) When using this terminal as a through terminal or when not using it at all,
set “000” or “031”.
Sets the voltage level gain of multi-function analog output 1 (terminal AM).
H4-02 Multi-Function Analog 1
The bias to be added ranges from 0 to +/- 10% when 10 V is assumed to be
(Terminal AM Output Gain)

Start-Up Programming &

<1>
100%.
Sets the voltage level bias for terminal AM.
H4-03 Multi-Function Analog 1
The bias added is 0 to ±10% with a maximum voltage output of
<1> (Terminal AM Bias Setting)
10 V as 100%.

<1> The parameter can be changed during run.

Operation
■ Changing Analog Output Settings
The following example illustrates how to program analog output terminal FM to generate a
signal proportional to drive output current (monitor U1-03). 4
Using H4-01 to Display Monitor Contents

Step Display/Result

1. Turn on the power to the drive. The initial display appears. ⇒

2. Press until the Parameter setting menu is displayed. ⇒

3. Press to enter the Parameter setting menu. ⇒

4. Press and to select H4-01. ⇒

5. Press to display the value currently set to H4-01. ⇒

6. Press and to set the output current (103). ⇒

7. Save the setting by pressing . ⇒

8. The display automatically returns to the parameter setting menu. ⇒

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 145
4.6 Basic Drive Setup Adjustments

Step Display/Result

9. Press the key until back at the Top Screen. ⇒

Adjusting the Analog Output Terminal Voltage with H4-02 and H4-03
Note: This example continues from Step 3 in the previous example.

Step Display/Result

1. Select H4-02 or H4-03 by pressing the and keys. ⇒

Press the key while the drive is stopped and the following
2. voltage is output for adjustment: output voltage = (10 V x Output ⇒
Gain (H4-02) + Output Bias (H4-03). Using this output, adjust
output gain (H4-02) and output bias (H4-03).
Figure 4.26

Output Voltage

10
Gain ˜ V
100
(%)
10 V

10
Bias ˜ V
100
(%) Monitor
0V Contents
0% 100%
Figure 4.26 Adjusting the Monitor Output

◆ Motor Protection: L1-01 and L1-02

This section explains how to set motor overload protection.
■ Electronic Thermal Motor Protection
The drive has built-in electronic thermal overload protection to detect overload conditions.
This protection meets standards set by UL and cUL for motor thermal overload protection.
The protective feature is activated when the output current rises above the motor rated
current for a specified time. This speed sensitive protective feature interrupts the motor
current to protect the motor wiring and windings in the event of overload, eliminating the
need for an external overload device. When multiple motors are used with a single drive,
separate overload devices are required to properly protect the individual motor branches.

146 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 4.6 Basic Drive Setup Adjustments

Related Parameters

Parameter
No. Name Description Setting Range Default Setting

10 to 200% of drive rated

Sets the motor nameplate full load current in
current
Motor amperes (A). This set value becomes the
Less than 11 kW: 2 digits Determined by
E2-01 Rated reference value for motor protection, torque
below the decimal point, o2-04 and C6-01
Current limit, and torque control. This value is
11 kW or more: 1 digit
automatically set during Auto-Tuning.

Start-Up Programming &

below the decimal point.
Sets the motor 2 name plate full load current in
Motor 2 amperes (A). This set value becomes the
10 to 200% of drive rated Determined by
E4-01 Rated reference value for motor protection, torque
current o2-04 and C6-01
Current limit, and torque control. This value is
automatically set during Auto-Tuning.

Operation
0 to 4 1
Enables or disables motor thermal overload
protection (OL1) Use L1-13 (Continuous Electrothermal
Motor Operation Selection) to select whether
0: Disabled
Overload electronic thermal value is “held” or “not
L1-01
Protection
Selection
1: Protection for general purpose motor
2: Protection for inverter motor held” when the power supply is turned off. 4
3: Protection for vector motor When connecting several motors to one
4: Protection for PM variable torque motor drive, set “0” (disabled) and install a thermal
relay on each motor.
Sets the electronic thermal overload protection
Motor detection time in the motor overload protection
Overload (OL1) function.
L1-02 0.1 to 5.0 1.0 min
Protection This setting rarely needs to be changed and
Time should be set in accordance with the overload
tolerance of the motor.

Note: Executing C6-01 (Duty Cycle) changes motor parameters E2 and E4 including motor rated
current to the values of the maximum applicable motor.
Digital Outputs (H2-01 through H2-03)

Setting Function Description

Motor Overload Closed = When OL1 function is at 90% of its trip point or
1F
OL1 Alarm Warning (including OH3) greater.

Setting Procedure
1. Set E2-01 (Motor Rated Current) and E4-01 (Motor 2 Rated Current) to the motor
rated current.
Note: 1. Values set for the current become the base current for electronic thermal overload protection.
2. These values are automatically set by performing Auto-Tuning.
3. The E4-01 setting is not needed if not using motor 2.
2. Set the proper motor protection level to L1-01.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 147
4.6 Basic Drive Setup Adjustments

The ability of the cooling fan to keep an induction motor cool varies by the speed
control range. Protection characteristics of the electronic thermal overload
protection should be set accordingly. Refer to Table 4.21 for motor types and
overload tolerances.
NOTICE: When connecting multiple motors to one drive, disable the electronic overload protection of the
drive (L1-01 = 0) and protect each motor with its own motor thermal overload. Failure to comply could result
in improper drive operation.

NOTICE: Inadequate motor protection could result in damage to the motor. Configure a motor thermal
overload to disconnect main power to the drive when tripped. When using a thermal relay, disable the motor
protection function (L1-01 = “0”).

3. Set the motor overcurrent alarm warning level.

When H2-01, H2-02, and H2-03 (Terminal MA, MB, and MC Function selection,
Terminal P1 Function Selection, and Terminal P2 Function Selection) are set to 1F
motor overload (OL1 alarm warning), a motor overload alarm is enabled. If the
electronic thermal value exceeds 90% of the overload detection level, the set output
terminal turns on.
Table 4.21 Motor Type and Overload Tolerances

Electrothermal
L1-01 Protection
Setting Motor Type Overload Tolerance Cooling Fan Capacity (100% motor
overload)
150
Rated Speed = 100% Speed

60 seconds

Operating continuously
100 General purpose motors are at less than line power
General- 90 designed to operate from frequency can trigger
Torque

purpose motor line power. The most motor overload

1 (%)
(standard 60
Continuous
effective cooling occurs protection (OL1). A
50
motor) when running at line power fault is then output and
A
B specifications. the motor will coast to
C stop.
05 33 100 120 167 200
㧔60Hz㧕
Speed (%)

150
Rated Speed = 100% Spee

60 seconds

100
Inverter Duty Motor designed to
Continuous operation
Torque

2 motor effectively self-cool at

between 6 and 50/60 Hz.
(1:10) (%) speeds as low as 6 Hz.
55
50
Continuous A
B

0 1 10 100 120 167 200

(60Hz)
S d (%)

148 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 4.6 Basic Drive Setup Adjustments

Electrothermal
L1-01 Protection
Setting Motor Type Overload Tolerance Cooling Fan Capacity (100% motor
overload)

150
Rated Speed = 100% Sp
60 seconds

100
Motor capable of effective
Vector motor 90
Continuous operation

Start-Up Programming &

3 Torque cooling at extremely low
(1:100) between 0.6 and 60 Hz.
(%) speeds (0.6 Hz).
50 A
Continuous
B

Operation
01 100 120 167 200

A: Typical maximum speed for Yaskawa motor frame number 200LJ and greater
B: Typical maximum speed for Yaskawa motor frame numbers 160MJ – 180LJ
C: Typical maximum speed for Yaskawa motor frame number 132MHJ or less
D: Typical maximum speed for Yaskawa motor frame number 132MJ or less
4
Notes on Motor Protection
• Motor protection meeting UL and cUL standards is achieved with the motor overload
protection time (L1-02) set to factory default setting. Normally, L1-02 (Motor Overload
Protection Time) does not require setting. If the motor overload tolerance is clear, set the
ovlerload protection time at hot start according to the motor. To detect overload earlier,
decrease the setting.
Note: Figure 4.27 illustrates motor protection operation time characteristics.
Figure 4.27

Operation Time (minutes)

10
7

3
Cold Start
1

0.4
Hot Start

0.1 Motor Current (%)

0 100 150 200 E2-01 = 100%

Figure 4.27 Motor Protection Operation

• Disable motor protection (L1-01 = 1) when running multiple motors from the same drive.
Attach a thermal relay for each motor to provide overload protection.
• Use L1-13 (Continuous Electrothermal Operation Selection) to select whether the
electrothermal value is “held” or “not held” when power supply is turned off. Default
setting is 1 (Enabled).

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 149
4.6 Basic Drive Setup Adjustments

• In the case of a general purpose (standard) motor, the cooling capability is reduced at a
low speed. Motor overload protection (OL1) may occur in frequencies lower than motor
rated current. Use an exclusive-use or inverter-duty motor to operate the drive at rated
current at low frequency.

◆ Drive Status Monitors: U1-01 to U6-19

Parameter group U displays various data regarding the operating status of the drive.
The following example demonstrates viewing output voltage reference (U1-06).

Step Display/Result

1. Turn on the power to the drive. The initial display appears. ⇒

2. Press until “Monitor Display” appears. ⇒

3. Press to enter the Parameter Setting Screen. ⇒

4. Press until U1-06 appears. ⇒

Press to display the voltage reference. The Output Voltage

5. ⇒
Reference appears.

Refer to Parameter List on page 309 for more details about Drive Status Monitors.
Table 4.22 Drive Status Monitors

No. Parameter Name Page No. Parameter Name Page

U1-01 Frequency Reference 376 U3-10 10th Most Recent Fault 382
Cumulative Operation Time at Most
U1-02 Output Frequency 376 U3-11 382
Recent Fault
Cumulative Operation Time at 2nd
U1-03 Output Current 377 U3-12 382
Most Recent Fault
Cumulative Operation Time at 3rd
U1-04 Control Mode 377 U3-13 382
Most Recent Fault
Cumulative Operation Time at 4th
U1-05 Motor Speed 377 U3-14 382
Most Recent Fault
Cumulative Operation Time at 5th
U1-06 Output Voltage Reference 377 U3-15 382
Most Recent Fault

150 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 4.6 Basic Drive Setup Adjustments

No. Parameter Name Page No. Parameter Name Page

Cumulative Operation Time at 6th
U1-07 DC Bus Voltage 377 U3-16 382
Most Recent Fault
Cumulative Operation Time at 7th
U1-08 Output Power 377 U3-17 382
Most Recent Fault
Cumulative Operation Time at 8th
U1-09 Torque Reference 377 U3-18 383
Most Recent Fault
Cumulative Operation Time at 9th
U1-10 Input Terminal Status 378 U3-19 383

Start-Up Programming &

Most Recent Fault
Cumulative Operation Time at 10th
U1-11 Output Terminal Status 378 U3-20 383
Most Recent Fault
U1-12 Drive Status 379 U4-01 Accumulated Operation Time 383
U1-13 Terminal A1 Input Voltage 379 U4-02 Number of Run Commands 383

Operation
U1-14 Terminal A2 Input Voltage 379 U4-03 Cooling Fan Operation Time 383
U1-16 Output Frequency after SoftStart 379 U4-05 Capacitor Maintenance 383
U1-18 oPE Fault 379 U4-07 IGBT Maintenance 383
U1-19 MEMOBUS/Modbus Error Code 380 U4-09 LED Check 384 4
U1-24 Input Pulse Monitor 380 U4-10 kWH, Lower 4 Digits 384
U1-25 Software Number (Flash) 380 U4-11 kWH, Upper 5 Digits 384
U1-26 Software Number (ROM) 380 U4-13 Peak Hold Current 384
U2-01 Current Fault 380 U4-14 Peak Hold Output Frequency 384
U2-02 Previous Fault 380 U4-16 Motor Overload Estimate (OL1) 384
U2-03 Frequency Reference at Previous Fault 380 U4-18 Frequency Reference Selection Results 384
Freq. Ref. from MEMOBUS/Modbus
U2-04 Output Frequency at Previous Fault 380 U4-19 384
Communications
U2-05 Output Current at Previous Fault 380 U4-20 Option Frequency Reference 384
U2-06 Motor Speed at Previous Fault 381 U4-21 Run Command Selection Results 385
U2-07 Output Voltage at Previous Fault 381 U4-22 MEMOBUS/Modbus Comm. Ref. 385
U2-08 DC Bus Voltage at Previous Fault 381 U4-23 Option Card Reference 385
U2-09 Output Power at Previous Fault 381 U5-01 PID Feedback 386
U2-10 Torque Reference at Previous Fault 381 U5-02 PID Input (feedback) 386
U2-11 Input Terminal Status at Previous Fault 381 U5-03 PID Output 386
U2-12 Output Terminal Status at Prev. Fault 381 U5-04 PID Setpoint 386
U2-13 Drive Operation Status at Pre. Fault 381 U6-01 Torque Reference (Internal) 386
Cumulative Operation Time at
U2-14 381 U6-02 Motor Secondary Current (Iq) 386
Previous Fault
Soft Starter Speed Reference at
U2-15 381 U6-03 Motor Excitation Current (ld) 386
Previous Fault
Output of speed control (ASR) (for
U2-16 Motor q-Axis Current at Previous Fault 381 U6-04 386
Simple V/f PG)

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 151
4.6 Basic Drive Setup Adjustments

No. Parameter Name Page No. Parameter Name Page

U2-17 Motor d-Axis Current at Previous Fault 381 U6-05 Output voltage reference (Vq) 386
U3-01 Most Recent Fault 381 U6-06 Output Voltage Reference (Vd) 386
U3-02 2nd Most Recent Fault 381 U6-07 q-axis ACR Output 386
U3-03 3rd Most Recent Fault 381 U6-08 d-Axis ACR Output 386
Energy Savings Coefficient
U3-04 4th Most Recent Fault 381 U6-17 386
Calculation Value
U3-05 5th Most Recent Fault 382 U6-18 PID Differential Feedback 386
U3-06 6th Most Recent Fault 382 U6-19 PID Adjusted Feedback 386
U3-07 7th Most Recent Fault 382 U6-20 Frequency Ref. Bias (Up/Down 2) 386
U3-08 8th Most Recent Fault 382 U6-21 Offset Frequency 387
U8-
U3-09 9th Most Recent Fault 382 Custom Monitors for DriveWorksEZ 387

152 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 4.7 Test Run

4.7 Test Run

◆ Powering Up the Drive and Operation Status Display

■ Powering Up the Drive
Review the following checklist before turning the power on.

Start-Up Programming &

Item to Check Description
Ensure the power supply voltage is correct:
200 V class: single-phase 200 to 240 Vac 50/60 Hz
200 V class: 3-phase 200 to 240 Vac 50/60 Hz

Operation
Power supply voltage 400 V class: 3-phase 380 to 480 Vac 50/60 Hz
Properly wire the power supply input terminals (R/L1, S/L2, T/L3).
(for single-phase 200 V class models, wire only R/L1 and S/L2)
Check for proper grounding of drive and motor.
Drive output terminals Properly wire drive output terminals U/T1, V/T2, and W/T3 with motor terminals U, V, 4
and motor terminals and W.
Control circuit terminals Check control circuit terminal connections.
Drive control terminal
Open all control circuit terminals (off).
status
Status of the load and
Uncouple the motor from the load.
connected machinery

■ Status Display
When the power supply to the drive is turned on, the LED operator lights will appear as
follows:

No. Name Description

Normal
Operation The data display area displays the frequency reference. flashes.

Data displayed varies by the type of fault. Refer to Fault Displays,

Fault Causes, and Possible Solutions on page 187 for more information
and corrective action. and are lit.
Main circuit low voltage (ex)

◆ Auto-Tuning
Auto-Tuning automatically sets and tunes parameters required for motor operation.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 153
4.7 Test Run

■ Types of Auto-Tuning
There are three types of Auto-Tuning. Refer to Auto-Tuning Selection on page 155 to select
the best type of Auto-Tuning for the application.

Type Setting Application Conditions and Benefits Control Mode

Assumes the motor can rotate during the
Rotational
Auto-Tuning process
Auto-Tuning for T1-01 = 3 V/f Control
Improves torque compensation, slip compensation,
V/f Control
energy savings, and speed search performance
Rotational Assumes the motor can rotate during the
Auto-Tuning for T1-01 = 0 Auto-Tuning process Open Loop Vector Control
OLV Control Achieves high-performance motor control
Stationary Auto-
Tuning for V/f For use when the motor cable exceeds 50 m
and OLV The motor cable length has been modified after V/f Control,
T1-01 = 2
Control Line-to- Auto-Tuning has been previously performed Open Loop Vector Control
Line Resistance When motor capacity and drive capacity differ
Only

Note: Auto-Tuning cannot be performed on permanent magnet motors (IPM, SPM, etc.).

154 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 4.7 Test Run

■ Auto-Tuning Selection
Figure 4.28

START

Select the Motor Control Mode A1-02

Start-Up Programming &

V/f Control Open Loop Vector PM Open Loop Vector Control
A1-02 = 0 A1-02 = 2 A1-02 = 5

Select a V/f pattern

Operation
E1-03

NO Is the total
Will the application
allow motor rotation
Can the load be
disconnected from
connected load
expected to be less 4
than 30% of the motor
for Auto-Tuning? the motor? rating?

YES NO YES NO
YES NOTICE: Auto-Tuning with
Is the cable a connected load is possible,
between the motor but may result in less than
and drive longer optimum performance.
than 50 m?

V/f Rotational
Auto-Tuning
YES NO
(T1-01 = 3)
Rotational Select V/f Control
Auto-Tuning Mode (A1-02 = “0”)
Stationary Auto-Tuning (T1-01 = 0)
for Terminal Resistance Only for the drive.
(T1-01 = 2) Note: Manually set parameters
when OLV control is needed.

Run the motor without the load.

Connect the load and run the motor.

Verify system operates as required.

Auto-Tuning finished.
Figure 4.28

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 155
4.7 Test Run

■ Before Auto-Tuning the Drive

Check the items below before Auto-Tuning the drive:
Basic Auto-Tuning Preparations
• Auto-Tuning automatically determines the electrical characteristics of the motor. This is
fundamentally different from other types of Auto-Tuning features used in servo systems.
• Before auto-tuning, be sure the input supply voltage equals or exceeds the motor rated
voltage. Performance can be enhanced by using a motor with a base voltage that is 20 V
(40 V for 400 V class models) lower than the input supply voltage. This may be of special
importance when operating the motor above 90% of base speed, where high torque
precision is required.
• Auto-Tuning is not possible with permanent magnet motors.
• To cancel Auto-Tuning, press the STOP key on the LED operator.
• The next table describes digital input and output terminal status during Auto-Tuning.

Auto-Tuning Type Digital Input Digital Output

Auto-Tuning for Energy Savings in V/f Control Not available Works the same during normal operation
Rotational-Type Auto-Tuning Not available Works the same during normal operation
Auto-Tuning for Resistance between Lines Not available Maintains the status at the start of Auto-Tuning

WARNING! When Auto-Tuning a motor that is used on an application in conjunction with a brake, take
special precaution to insure the brake stays applied. Auto-Tuning activates the drive multi-function outputs
per the table below. Therefore, a brake may be released while the motor is uncoupled from the load,
resulting in an unsafe condition. Proper precautions must therefore be taken prior to performing Auto-
Tuning.

Note: It is recommended that Rotational Auto-Tuning be performed with the load disconnected.
Failure to comply could result in improper drive operation. If rotational Auto-Tuning is
performed for a motor coupled to a load, the motor constants will be inaccurate and the motor
may exhibit abnormal operation. Disconnect or decouple the motor from the load.
Rotational Auto-Tuning for V/f Control
• Motor rotates during Auto-Tuning.
• Sets parameters required for torque compensation, slip compensation, energy savings, and
speed search.
• Available only when the drive is set for V/f Control.
• Required to perform Estimation-Type Speed Search when using V/f Control.
Rotational Auto-Tuning for Open Loop Vector Control
• Used only when in Open Loop Vector Control.
• Perform only with the motor uncoupled from the load for applications requiring high
performance over a wide speed range.
• Disconnect the load before Auto-Tuning the drive and motor. Performing Rotational
Auto-Tuning with the load connected will set motor parameters incorrectly, and also be
dangerous because irregular motor rotation will occur.
• It is possible to perform Rotational Auto-Tuning with a connected load if the load is less
than 30% of the rated load.
• Ensure a motor-mounted brake is fully released.

156 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 4.7 Test Run

• Connected machinery should not produce enough power to rotate the motor.
Stationary Auto-Tuning for Terminal Resistance Only
• If the motor cable lead length has been significantly modified after Auto-Tuning has
already been performed, perform Stationary Auto-Tuning with the new cables.
• Perform when using motor cables longer than 50 m with V/f Control.
WARNING! Electrical Shock Hazard. When executing stationary Auto-Tuning for line-to-line resistance only,
the motor does not rotate, however, power is applied. Do not touch the motor until Auto-Tuning is completed.
Failure to comply may result in injury from electrical shock.

Start-Up Programming &

Note: When auto-tuning a motor that is used on an application in conjunction with a brake, take special
precaution to ensure the brake stays applied.

■ Auto-Tuning Fault Codes

Calculation of abnormal measurements or pressing STOP before completion will

Operation
interrupt Auto-Tuning.
Refer to Auto-Tuning Errors on page 186 for more information.
Figure 4.29

A B
4

A – Normal Auto-Tuning Display B – Auto-Tuning Interrupted

Figure 4.29 Auto-Tuning Interruption Display

■ Performing Auto-Tuning
The following example illustrates how to perform Rotational Auto-Tuning.
Note: The following example is shown with the drive in Open Loop Vector Control
(A1-02 = 2).
Selecting the Type of Auto-Tuning

Step Display/Result

1. Turn on the power to the drive. The initial display appears. ⇒

2. Press the key until the Auto-Tuning screen appears. ⇒

3. Press to begin setting parameters. ⇒

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 157
4.7 Test Run

Step Display/Result

4. Press to display the value for T1-01. ⇒

5. Press to select the digit to edit. ⇒

6. Press and set the drive to perform Rotational Auto-Tuning

⇒
(00).

7. Save the setting by pressing . ⇒

8. The display automatically returns to the screen shown in Step 3. ⇒

9. Press the key until back at the Top Screen. ⇒

Enter Data from the Motor Nameplate

After selecting the type of Auto-Tuning, enter the required data from the motor nameplate.
Note: These instructions continue from Step 7 in Selecting the Type of Auto-Tuning.

Step Display/Result

1. Press to access the motor output power parameter T1-02. ⇒

2. Press to view the default setting. ⇒

3. Press to select the digit to edit. ⇒

Press and enter “0.2.” Enter value based on motor

4. ⇒
nameplate data.

5. Press to save the setting. ⇒

6. The display automatically returns to the screen shown in Step 1. ⇒

158 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 4.7 Test Run

Step Display/Result

Repeat Steps 1 through 5 to set the following parameters:T1-03,

Motor Rated Voltage T1-04, Motor Rated CurrentT1-05, Motor Base
7. ⇒
FrequencyT1-06, Motor Poles;
T1-07, Motor Base Frequency

Start-Up Programming &

Note: For the details of each setting, Refer to Motor Data for Auto-Tuning on page 160. For
stationary Auto-Tuning for line-to-line resistance only, set T1-02 and T1-04.
Starting Auto-Tuning
WARNING! Sudden Movement Hazard. The drive and motor may start unexpectedly during Auto-Tuning,

Operation
which could result in death or serious injury. Ensure the area surrounding the drive motor and load are clear
before proceeding with Auto-Tuning.

WARNING! Electrical Shock Hazard. High voltage will be supplied to the motor when stationary Auto-Tuning
is performed even with the motor stopped, which could result in death or serious injury. Do not touch the
motor until Auto-Tuning has been completed.
4
NOTICE: Auto-Tuning will not function properly if a holding brake is engaged on the load. Failure to comply
could result in improper operation of the drive. Ensure the motor can freely spin before beginning Auto-
Tuning.

NOTICE: Never perform rotational Auto-Tuning for a motor connected to a load. Failure to comply could
result in improper drive operation. If rotational Auto-Tuning is performed for a motor coupled to a load, the
motor constants will be inaccurate and the motor may exhibit abnormal operation. Disconnect or decouple
the motor from the load.

Enter the required information from the motor nameplate. Press to proceed to the
Auto-Tuning start screen.

Step Display/Result
After setting T1-07 as illustrated in the previous section, press
1. ⇒
and confirm the display is as follows:

Press RUN to activate Auto-Tuning. flashes.

2. Note: The first digit indicates which motor is undergoing ⇒
Auto-Tuning (motor 1 or motor 2). The second digit indicates the
type of Auto-Tuning being performed.

3. Auto-Tuning finishes in approximately one to two minutes. ⇒

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 159
4.7 Test Run

■ Motor Data for Auto-Tuning

Table 4.23 Parameters Set During Auto-Tuning

Control
No. Name Description Range Def. Mode
V/f OLV
Selects which set of motor parameters are set during Auto-
Tuning. If motor 2 selection (H1- =16) is not selected, this
parameter will not be displayed.
Motor
1: Motor 1 - E1 to E2
T1-00 Selection 1, 2 1 A A
2: Motor 2 - E3 to E4. <1> Enabled when motors 1 and 2 are
1/2
switched to each other (H1- =16).
Displayed only when either multi-function contact output H1-
01 through H1-07 is set to 16.
Selects the Auto-Tuning mode.
0: OLV Rotational Auto-Tuning
Auto- 0
2: Terminal resistance only, Stationary Auto-Tuning
Tuning (“2” in
T1-01 3: V/f Rotational Auto-Tuning. 0, 2, 3 A A
Mode V/f
Only settings 2 and 3 are available when using V/f Control.
Selection mode)
Only setting 2 is available when using motor 2.
Settings 0 and 2 are available when using OLV Control.
Sets the motor rated output power. A set value that can provide
Motor
stable control in the open loop control mode ranges from 50 to 0.00 to 0.40
T1-02 Rated A A
100% of the drive rating. In case of motors that operate above 650.00 kW
Power
base speed, set the value at base speed.
Motor Set the motor base voltage according to the information printed
T1-03 0.0 to 200.0
Rated on the motor nameplate. In case of motors that operate above A A
<2> 255.5 V
Voltage base speed, set the value at base speed.
Enter the motor-rated current as specified on the motor
10 to
nameplate. Det. by
Motor 200% of
For best performance when using OLV select the drive so that o2-04
T1-04 Rated drive A A
the motor represents 50 to 100% of the drive rated current. and
Current rated
Enter the current required at base speed for motors with C6-01
current
extended speed ranges.
Motor Enter the motor base frequency as specified on the motor
0.0 to 60.0
T1-05 Base nameplate. Enter the motor base frequency for extended speed A A
400.0 Hz
Frequency range motors.
Number
T1-06 of Motor Enter number of motor poles indicated on motor nameplate. 2 to 48 4 A A
Poles
Motor Sets the base speed of the motor in revolutions per minute r/min
0 to 1750.
T1-07 Base (RPM). Enter the motor base speed for extended speed range A A
24000 r/min
Speed motors.

160 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 4.7 Test Run

Control
No. Name Description Range Def. Mode
V/f OLV
Provides iron loss for determining Energy Saving coefficient.
When power is cycled, the value set to E2-10 will appear (the
Motor 0 to
T1-11 motor iron loss). If T1-02 is changed, an initial value for the 14W A −
Iron Loss 65535
motor capacity will appear that is close to the capacity that was
changed.

Start-Up Programming &

<1> Normally not displayed.
<2> Voltage and frequency settings for vector motors and drive motors are often lower than for standard motors. Be
sure to enter Auto-Tuning data according to the motor nameplate and motor data sheets. If the no-load voltage and
frequency values are shown, enter those values into T1-03 and T1-05.

■ Precision Settings for Auto-Tuning

Operation
Basic motor nameplate data can be used to auto-tune a motor. However, improved
performance can be achieved by using precise data for base voltage and base frequency. If
the base no-load voltage and frequency are known, enter this data when executing auto-
tuning to improve performance.
4
Parameter Normal Settings Precision Tuning
Enter the no-load voltage when the motor is operating at its
T1-03 Enter the motor rated voltage
rated revolutions per minute
Enter the no-load frequency when the motor is operating at its
T1-05 Enter the motor base frequency
rated revolutions per minute

◆ No-Load Operation
This section explains how to operate the drive with the motor uncoupled from the load
during a test run.
■ Before Starting the Motor
Check the following items before operation:
• Ensure the area around the motor is safe.
• Set the proper motor rated current to T1-04 to prevent overheating or other damage from
motor overload.
• Ensure external emergency stop circuitry is working properly and other safety precautions
have been taken.
■ During Operation
Check the following items during operation:
• The motor should rotate smoothly (i.e., no abnormal noise or oscillation).
• The motor should accelerate and decelerate smoothly.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 161
4.7 Test Run

■ Operation Instructions
The following example illustrates a procedure to run the drive using the digital operator.
Note: Before starting the motor, set the frequency reference to 6 Hz. Refer to The Drive and
Programming Modes on page 97 for instructions.

Step Display/Result

1. Turn on the power to the drive. The initial display appears. ⇒

Press the key to select LOCAL. The LO/RE LED will

2. ⇒
STOP
turn on.

Press RUN to give the drive a run command. RUN will light ⇒
STOP

3.
and the motor will rotate at 6 Hz.

Off On

Motor

Ensure the motor is rotating in the correct direction and no faults or

4. ⇒
alarms occur.

Forward

If there is no error in step 4, press to increase the frequency

reference. Increase the frequency in 10 Hz increments verifying
smooth operation results at all speeds. For each frequency monitor
5. the drive output current (U1-03) through the LED operator to
confirm the current is well below the motor rated current. Example:
6 Hz → 50 Hz/60 Hz .
Note: Refer to Auto-Tuning Errors on page 186 for help with
errors that occur while Auto-Tuning the drive.

162 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 4.7 Test Run

Step Display/Result

The drive should operate normally. Press STOP to stop the

6. ⇒ STOP

motor. RUN flashes until the motor comes to a complete stop.

Start-Up Programming &

Flashing Off

Note: To operate the drive, run (forward/reverse) command and frequency (or multi-step speed)
reference are needed. Input these commands and references to the drive.

◆ Operating with the Load Connected

Operation
After performing a no-load test run, connect the motor and proceed to run the load.
■ Notes on Connected Machinery
• Clear the area around the motor. 4
• The motor should come to a complete stop without problems. Connect the machinery.
• Fasten all installation screws properly. Check that the motor and connected machinery are
held in place.
• Confirm that the Fast-stop circuit or mechanical safety operate correctly.
• Prepare to press the STOP button in the case of an emergency.
■ Checklist Before Operation
• The motor should rotate in the proper direction.
• The motor should accelerate and decelerate smoothly.
• Check U1-03 to ensure there is not overcurrent.
If the application permits running the load in the reverse direction, try changing motor
direction and the frequency reference and watch for abnormal motor oscillation or vibration.
Correct the problem if hunting or oscillation occurs or if there are control-related problems.
Refer to Motor Hunting and Oscillation Control Parameters on page 180.
■ Operating the Motor under Loaded Conditions
Test run the application similarly to the no-load test procedure when connecting the
machinery to the motor.

◆ Verifying Parameter Settings and Backing Up Changes

Check changes to parameter settings as a result of Auto-Tuning using the Verify function.
Refer to Verifying Parameter Changes: Verify Menu on page 102.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 163
4.7 Test Run

Save the verified parameter settings. Change the access level or set a password to the drive
to prevent accidental modification of parameter settings.
■ Backing Up Parameter Values: o2-03
Performing the following procedure stores all parameters settings to drive memory where
they can later be recalled if necessary. Set o2-03 to “1” to save parameter changes. This
saves all parameter settings, and then returns o2-03 to 0. The drive can now “recall” the
saved parameters by performing a “user-initialization” (A1-03 = 1110).

Parameter Setting Default

No. Name Description Range Setting
Allows storing of parameter settings as a User Initialization
Selection.
0: Saved/Not set
User 1: Set Defaults - Saves current parameter settings as user default
o2-03 Parameter settings. 0 to 2 0
Default Value 2: Clear All - Clears the currently saved user settings. After
saving the user parameter set value, the items of 1110 (User
Parameter Initialize) are displayed in A1-03 (User Parameter
Default Value).
Selects a method to initialize the parameters.
0: No Initialize
1110: User Initialize (The user must first program and store
Initialize desired settings using parameter o2-03)
A1-03 0 to 5550 0
Parameters 2220: 2-Wire Initialization (parameter initialized prior to
shipment)
3330: 3-Wire Initialization
5550: OPE4 Fault reset

■ Parameter Access Level: A1-01

Setting the Access Level for “Operation only” (A1-01 = 0) allows the user to access
parameters A1-†† and U†-†† only. Other parameters are not displayed.
Setting the Access Level for “User Parameters” (A1-01 = 1) allows the user to access
parameters that have been previously saved as Preferred Parameters. This is helpful when
displaying only the relevant parameters for a specific application.

Parameter Setting
No. Description Default
Name Range
Selects which parameters are accessible via the digital operator.
0: Operation only (A1-01, -04, and -06 can be set and monitored. U
Access
parameters can be monitored)
A1-01 Level 0 to 2 2
1: User Parameters (Only those recently changed among application
Selection
parameters A2-01 to -16 and A2-17 to -32 can be set and monitored)
2: Advanced Access Level (All parameters can be set and monitored)

164 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 4.7 Test Run

No. Parameter Description Setting Default

Name Range
Parameters selected by the user are stored to the User Parameter menu.
This includes recently viewed parameters or parameters specifically
selected for quick access.
A2-01 Preferred If parameter A2-33 is set to 1, recently viewed parameters will be
b1-01 to
to Parameters listed between A2-17 and A2-32. Parameters A2-01 through A2-16 –
o2-08
A2-32 1 to 32 must be manually selected by the user.
If A2-33 is set to 0, then recently viewed parameters will not be saved
to the User Parameter group. The entire A2 parameter group is now

Start-Up Programming &

available for manual programming.
0: Parameters A2-01 through A2-32 are reserved for the user to create
Preferred a list of User Parameters.
Parameter 1: Save history of recently viewed parameters. Recently edited
A2-33 0,1 1
Automatic parameters will be saved to A2-17 through A2-32 for quick access.

Operation
Selection The most recently changed parameter is registered in A2-17. The
second most recently changed parameter is registered in A2-18.

■ Password Settings: A1-04, A1-05

The user can set a password to the drive to restrict access. The password is selected via 4
parameter A1-05. The selected password must be entered in parameter A1-04 to unlock
parameter access (i.e., parameter setting A1-04 must match the value programmed into A1-
05). The following parameters cannot be viewed or edited until the value programmed into
A1-04 correctly matches the value as programmed in parameter A1-05: A1-01, A1-02, A1-
03, A1-06 and A2-01 through A2-33.
Note: Parameter A1-05 is hidden from view. To display A1-05, access parameter A1-04 and
simultaneously depress the key and the key.

■ Copy Function (Optional)

Using an option, the parameter setting can be copied to another drive. Storing the modified
contents can make restoration easy since the parameters do not have to be set from the
beginning if the drive breaks down and must be replaced. For this drive, the following two
options can be used:
• Copy unit with USB (USB converter with copy function)
• Drive Wizard (Parameter management tool of PC application software)
Copy Unit with USB
Connect and exclusive-use cable to the communication connector on the drive and use the
ON/OFF switch on the copy unit with USB to copy the data
Drive Wizard
Use Drive Wizard to copy the parameter setting to another drive. For details, refer to Help in
the Drive Wizard software.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 165
4.7 Test Run

◆ Jog Operation: FJOG/RJOG

Digital inputs programmed as Forward Jog (H1- = 12) and Reverse Jog (H1- = 13)
will be Jog inputs that do not require a run command. Closing the terminal set for Forward
Jog input will cause the drive to ramp to the Jog Frequency Reference (d1-17) in the forward
direction. The Reverse Jog will cause the same action in the reverse direction. The Forward
Jog and Reverse Jog can be set independently.
■ Jog Operation Parameters

Setting Default
No. Name Description Range Setting
Frequency reference when: “Jog Frequency Reference” is
selected via multi-function input terminals. “Jog Frequency
Jog Frequency Reference” has priority over “Multi-Step Speed Reference 1 to 0.00 to
d1-17 6.00 Hz
Reference 16." Parameter d1-17 is also the reference for the JOG key on 400.00
the digital operator, and the multi-function inputs “Forward
Jog” and “Reverse Jog.”

■ Selections for Digital Input Terminals S1 to S7 (H1-01 to H1-07)

Setting Name
12 FJOG Command (ON: rotates forward at the Jog frequency set to d1-17)
13 RJOG Command (ON: rotates in reverse at the Jog frequency set to d1-17)

■ Connection Example for the Jog Function

In this example, H1-07 = 12 and d1-17 = 6.0 Hz.
Figure 4.30

Drive
Three-Phase 200 Vac
(400 Vac) R/L1 U/T1
S/L2 V/T2 M
T/L3 W/T3

S7 (FJ0G)

SC

Figure 4.30 Jog Command from External Terminals

166 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 4.7 Test Run

Figure 4.31

6.0 Hz

Output
Frequency

ON
Jog Reference
(FJ0G)

Start-Up Programming &

Figure 4.31 Jog Operation Pattern

■ Jog Operation Procedures

Set H1-07 (Multi-Function Contact Input Terminal S7 Function Selection) to “12” (FJOG

Operation
command).

Step Display/Result

1. Turn the power on to the drive. The initial display appears. ⇒ 4

2. Press the key until the Parameter Setting menu appears. ⇒

3. Press to enter the Parameter Setting menu. ⇒

Press and until H1-07 appears.Note: Select a

4. ⇒
parameter between H1-01and H1-07.

5. Press and set the value for H1-07. ⇒

Press and until “12” appears on the screen. Note:

6. ⇒
At jog operation in reverse run, set multi-function contact input to
13.

7. Press to save the setting. ⇒

To begin rotating the motor:

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 167
4.7 Test Run

Step Display/Result

Turn the power on to the drive. The initial display appears.Note: Set
1. ⇒
the drive to REMOTE.

Motor
With multi-function contact input terminal S7 closed, the motor
2. rotates forwards at 6 Hz. ⇒
Note: No run command is necessary when using the Jog frequency.

3. The drive will stop with terminal S7 open. ⇒

◆ Multi-Step Speed Operation (4-Step Speed)

Select up to 17 preset references (including Jog reference) using five multi-function inputs
S3 through S7. Four multi-step references can be selected using two multi-function inputs as
illustrated in Figure 4.32.
■ Multi-Step Speed Operation Parameters

No. Name Description

d1-01 Frequency Reference 1 Frequency reference. o1-03 determines the units, with Hz as the default.
Frequency reference when multi-function input “Multi-Step Speed Reference
d1-02 Frequency Reference 2
1" (H1- = 3) is on. Setting unit: set by o1-03.
Frequency reference when multi-function input “Multi-Step Speed Reference
d1-03 Frequency Reference 3
2” (H1- = 4) is on. Setting unit: set by o1-03.
Frequency reference when multi-function input “Multi-Step Speed Reference 1,
d1-04 Frequency Reference 4
2" (H1- = 3 and 4) are both on. Setting unit: set by o1-03.

■ Digital Input

Terminal Parameter Setting Contents

S5 H1-05 3 Multi-Step Speed Reference 1
S6 H1-06 4 Multi-Step Speed Reference 2

■ Wiring Example
Set up external switches SW1 and SW2.

168 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 4.7 Test Run

Figure 4.32

Drive
Three-Phase, 200 Vac R/L1 U/T1
(AC400 V)
S/L2 V/T2 M
T/L3 W/T3

SW1 S5

SW2 S6

SC

Start-Up Programming &

Figure 4.32 Control Terminals for 4 Multi-Step Speeds
Figure 4.33

Freq Ref 4
Frequency
Reference Freq Ref 3

Operation
Freq Ref 2

Freq Ref 1

Forward/Reverse Run/Stop ON

Multi-Step Speed 1 OFF ON ON

4
Multi-Step Speed 2 OFF ON

Figure 4.33 4-Step Speed Time Chart

■ Setting Procedure

Step Display/Result

1. Turn on the power to the drive. The initial display appears. ⇒

Set the frequencies listed below to the specified parameters:

1. d1-01 = 5 Hz: Step 1 <1>
2. 2. d1-02 = 20 Hz: Step 2 <2>
3. d1-03 = 50 Hz: Step 3
4. d1-04 = 60 Hz: Step 4

3. Press the key until the initial display appears.

4. turns on. ⇒

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 169
4.7 Test Run

Step Display/Result

5. Press to select LOCAL. The LO/RE light will turn on. ⇒ STOP

Off On

Press RUN to run the motor at 5 Hz. The RUN light will turn
6. ⇒ STOP

on.

Off On

With SW1closed, the drive runs the motor at Multi-Step Speed 2

7. ⇒
(20 Hz).

With SW1 open and SW2 closed, the drive runs the motor at
8. ⇒
Multi-Step 3 (50 Hz).

With both SW1 and SW2 closed, the drive runs the motor at
9. ⇒
Multi-Step 4 (60 Hz).

Press STOP to stop the drive. The RUN light will flash until the
10. ⇒ STOP

motor comes to a complete stop.

Flashing Off

<1> When the frequency reference is assigned to the LED operator (b1-01=0), the first step in a multi-step speed
sequence comes from d1-01.
<2> Set H3-10 (Multi-function Analog Input (current) Terminal A2 Function Selection) to “F” (not used).

Note: When a run command is input from the control circuit terminal, the frequency referenc value is
selected as follows: When b1-01 = 0 and the run command is given, the drive uses the frequency
set to d1-01. When b1-01 = 1 and the run command is given, the drive uses the frequency
reference value input to analog control terminal A1.

170 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 4.8 Test Run Checklist

4.8 Test Run Checklist

Review the checklist before performing a test run. Check each item that applies.

No. Checklist Page

1 Thoroughly read the manual before performing a test run.

Start-Up Programming &

2 Turn the power on. 153

3 Set the voltage for the power supply to E1-01. 138

Check the items that correspond to the control mode being used.

Operation
WARNING! Ensure start/stop and safety circuits are wired properly and in the correct state before
energizing the drive. Failure to comply could result in death or serious injury from moving equipment. When
programmed for 3-wire control, a momentary closure on terminal S1 may cause the drive to start.

4
No. Checklist Page

V/f Control (A1-02 = 0)

Select the best V/f pattern according to the application and motor characteristics.
4 139
Example: If using a motor with a rated frequency of 60.0 Hz, set E1-03 to “1”.
5 Perform Auto-Tuning for Energy Savings if using Energy Saving functions. 155
Open Loop Vector Control (A1-02 = 2)
6 Uncouple the load from the motor when performing Rotational Auto-Tuning. 153

7 Perform Rotational Auto-Tuning. 157

The following data entered during Auto-Tuning should match the information
written on the motor nameplate:
motor rated output power (kW) → T1-02
rated voltage (V) → T1-03
8 160
rated current (A) → T1-04
base frequency (Hz) → T1-05
number of motor poles → T1-06
motor rotations per minutes (r/min) → T1-07
PM Open Loop Vector Control (A1-02 = 5)
9 Set permanent motor parameters E5-01 through E5-24 110

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 171
4.8 Test Run Checklist

Proceed to the following checklist after checking items 4 through 9.

No. Checklist Page

10 The should illuminate after giving a run command.

To give a run command and frequency reference from the LED Digital Operator,
11 press to set to LOCAL. The LO/RE key lights while LOCAL is 104
displayed.
If the motor rotates in the opposite direction during the test run, switch two of the
12 153
drive output terminals (U/T1, V/T2, W/T3).
13 Select the correct duty rating (C6-01) for the application. 134
Set the correct values for the motor rated current (E2-01) and the motor protection
14 146
selection (L1-01) to ensure motor thermal protection.
If the run command and frequency reference are provided via the control circuit
15 104
terminals, set the drive for REMOTE and be sure the LO/RE light is out.
If the control circuit terminals should supply the frequency reference, select the
16 correct voltage input signal level (0 to 10 V) or the correct current input signal 104
level (4 to 20 mA).
17 Set the proper voltage to terminal A1. (0 to 10 V) 124

18 Set the proper current to terminal A2. (4 to 20 mA) 125

When current input (4 to 20 mA) is used, set H3-09 to “2” (Current Input) and set
19 125
H3-10 to “0”.
When current input (4 to 20 mA) is used, switch the drive built-in DIP switch S1
20 125
from V-side (OFF) to I-side (ON).
Set the minimum and maximum frequency references to the desired values. Make
the following adjustments if the drive does not operate as expected:
Voltage input, 0 to 10 V: For terminal A1, adjust the frequency reference gain
21 (H3-03) until reaching the desired value (60 Hz).
Current input, 4 to 20 mA: For terminal A2, adjust the current bias (H3-12) until
the frequency reference reaches 0.0 Hz. Next adjust the current gain (H3-11) until
the frequency reference reaches 60 Hz.

172 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 5
Troubleshooting
This chapter provides descriptions of the drive faults, alarms,
errors, related displays, and possible solutions. This chapter can
also serve as a reference guide for tuning the drive during a trial
run.

5.1 SECTION SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174

5.3 DRIVE ALARMS, FAULTS, AND ERRORS. . . . . . . . . . . 181
5.4 FAULT DETECTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187
5.5 ALARM DETECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . 206
5.6 OPERATOR PROGRAMMING ERRORS . . . . . . . . . . . . 217
5.7 AUTO-TUNING FAULT DETECTION. . . . . . . . . . . . . . . . 222
5.8 DIAGNOSING AND RESETTING FAULTS . . . . . . . . . . . 226
5.9 TROUBLESHOOTING WITHOUT FAULT DISPLAY. . . . 228

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 173
5.1 Section Safety

5.1 Section Safety

DANGER
Electrical Shock Hazard
Do not connect or disconnect wiring while the power is on.
Failure to comply will result in death or serious injury.

WARNING
Electrical Shock Hazard
Do not operate equipment with covers removed.
Failure to comply could result in death or serious injury.
The diagrams in this section may illustrate drives without covers or safety
shields to display details. Be sure to reinstall covers or shields before
operating the drives and run the drives according to the instructions
described in this manual.

Always ground the motor-side grounding terminal.

Improper equipment grounding could result in death or serious injury by
contacting the motor case.

Do not touch terminals before the capacitors have fully discharged.

Failure to comply could result in death or serious injury.
Before wiring terminals, disconnect all power to the equipment. The
internal capacitor remains charged even after the drive input power is
turned off. The charge indicator LED will extinguish when the DC bus
voltage is below 50 Vdc. To prevent electric shock, wait at least five
minutes after all indicators are off and measure the DC bus voltage level to
confirm safe level.

174 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 5.1 Section Safety

WARNING
Do not allow unqualified personnel to perform work on the drive.
Failure to comply could result in death or serious injury.
Installation, maintenance, inspection and servicing must be performed only
by authorized personnel familiar with installation, adjustment and
maintenance of AC drives.

Do not perform work on the drive while wearing loose clothing,

jewelry, or without eye protection.
Failure to comply could result in death or serious injury.

Troubleshooting
Remove all metal objects such as watches and rings, secure loose clothing
and wear eye protection before beginning work on the drive.

Do not remove covers or touch circuit boards while the power is on.
Failure to comply could result in death or serious injury.
5
WARNING
Fire Hazard
Tighten all terminal screws to the specified tightening torque.
Loose electrical connections could result in death or serious injury by fire
due to overheating of electrical connections.

Do not use an improper voltage source.

Failure to comply could result in death or serious injury by fire.
Verify that the rated voltage of the drive matches the voltage of the
incoming drive input power before applying power.

Do not use improper combustible materials.

Failure to comply could result in death or serious injury by fire.
Attach the drive to metal or other noncombustible material.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 175
5.1 Section Safety

NOTICE
Observe proper electrostatic discharge procedures (ESD) when
handling the drive and circuit boards.
Failure to comply may result in ESD damage to the drive circuitry.

Never connect or disconnect the motor from the drive while the drive
is outputting voltage.
Improper equipment sequencing could result in damage to the drive.

Do not use unshielded cable for control wiring.

Failure to comply may cause electrical interference resulting in poor
system performance. Use shielded twisted-pair wires and ground the shield
to the ground terminal of the drive.

Do not allow unqualified personnel to use the product.

Failure to comply could result in damage to the drive or braking circuit.
Carefully review instruction manual TOBPC72060000 when connecting a
braking option to the drive.

Do not modify the drive circuitry.

Failure to comply could result in damage to the drive and will void
warranty.
Yaskawa is not responsible for modification of the product made by the
user.

Check all the wiring after installing the drive and connecting other
devices to ensure that all connections are correct.
Failure to comply could result in damage to the drive.

176 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 5.2 Motor Performance Fine Tuning

5.2 Motor Performance Fine Tuning

This section offers helpful information for counteracting oscillation, hunting, or other faults
that occur while performing a trial run. Refer to the section below that corresponds to the
motor control method used.
Note: This section describes parameters that are commonly edited. Consult Yaskawa for more
information on detailed settings and fine-tuning the drive.

◆ V/f Motor Control Method Tuning

Table 5.1 Parameters for Tuning the Drive in V/f Motor Control Method

Default Suggested
Problem Parameter No. Countermeasure Value Setting

Troubleshooting
• If insufficient motor torque relative to the
• Motor hunting and Hunting size of the load causes hunting, reduce the
oscillation at speeds Prevention Gain setting. 1.00 0.50 to 2.00
between 10 and 40 Hz (n1-02) • When motor hunting and oscillation occur
with a light load, increase the setting.
• If the motor noise is too loud, increase the

• Motor noise Carrier

carrier frequency.
• When motor hunting and oscillation occur at 5
• Motor hunting and Frequency speeds up to 40 Hz, lower the carrier 7 (Swing
1 to A
oscillation at speeds up Selection frequency. PWM 1)
to 40 Hz (C6-02) • The default setting for the carrier frequency
depends on the drive capacity (o2-04) and the
Drive Duty Selection (C6-01).
• Poor torque or speed Torque • If motor torque and speed response are too
response Compensation slow, decrease the setting. 200 ms 100 to 1000
• Motor hunting and Primary Delay • If motor hunting and oscillation occur, <1> ms
oscillation Time (C4-02) increase the setting.
• Poor motor torque at • If motor torque is insufficient at speeds below
Torque
speeds below 10 Hz 10 Hz, increase the setting.
Compensation 1.00 0.50 to 1.50
• Motor hunting and • If motor hunting and oscillation with a
Gain (C4-01)
oscillation relatively light load, decrease the setting.
Mid Output • If torque is insufficient at speeds below 10
• Poor motor torque at Voltage A Hz, increase the setting. E1-08:
low speeds (E1-08) • If motor instability occurs at motor start, 16.0 V Initial value
• Poor motor instability at Minimum decrease the setting. Note: The recommended E1-10: ±5 V
motor start Output Voltage setting value is for 200 V class drives. Double 12.0 V
(E1-10) this value when using a 400 V class drive.
Slip • After setting the motor-rated torque (E2-01),
Compensation motor-rated slip (E2-02) and motor no-load
• Poor speed precision - 0.5 to 1.5
Gain current (E2-03), adjust the slip compensation
(C3-01) gain (C3-01).

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 177
5.2 Motor Performance Fine Tuning

<1> Default settings change when the Control Method is changed (A1-02) or a different V/f pattern is selected using
parmaeter E1-03. The default setting shown is for V/f Control.

Note: Use slip compensation to improve speed precision in V/f Control. First make sure that the proper
values have been set for the motor rated current to E2-01, motor rated slip (E2-02), and motor
no-load current (E2-03). Next, adjust the slip compensation gain set to C3-01 so that it is
between 0.5 to 1.5.

◆ Open Loop Vector (OLV) Motor Control Method Tuning

Table 5.2 Parameters for Tuning the Drive in OLV Motor Control Method

Default Suggeste
Problem Parameter No. Countermeasure
Value d Setting
• Poor motor torque and speed • If motor torque and speed response are too
response slow, gradually decrease the setting by
AFR Gain
• Control motor hunting and 0.05. 1.00 0.50 to 2.00
(n2-01)
oscillation at speeds between • If motor hunting and oscillation occur,
10 and 40 Hz. gradually increase the setting by 0.05.
• To improve motor torque speed response,
gradually reduce this setting by
10 ms and check the performance.
• Poor motor torque and speed • If motor hunting and oscillation occur as a
response AFR Time result of load inertia, gradually increase
50 to 2000
• Control motor hunting and Constant 1 the setting by 50 ms and check the 50 ms
ms
oscillation at speeds between (n2-02) performance. Note: Ensure that n2-02 ≤
10 and 40 Hz. n2-03. When making adjustments to n2-
02, set C4-02 (Torque Compensation
Primary Delay Time Constant 1)
accordingly.
• If overvoltage trips occur, gradually
increase this setting by 50 ms.
• Overvoltage trips when • If response is slow, gradually reduce this
AFR Time
accelerating, decelerating, or setting by 10 ms. Note: Ensure that n2-02 750 to 2000
Constant 2 750 ms
during sudden speed or load ≤ n2-03. When making adjustments to n2- ms
(n2-03)
changes. 03, increase the value of
C4-06 (Torque Compensation Primary
Delay Time 2) proportionally.
• To improve motor torque speed response,
gradually reduce this setting by 2 ms and
Torque
• Poor motor torque and speed check the performance.
Compensation
response • If motor hunting and oscillation occur, 20 ms 20 to 100
Primary Delay
• Motor hunting and gradually increase this setting by 10 ms. <1> ms
Time Constant 1
oscillation. Note: Ensure that C4-02 ≤ C4-06. When
(C4-02)
making adjustments to C4-02, increase n2-
02 (AFR Time Constant) proportionally.

178 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 5.2 Motor Performance Fine Tuning

Problem Parameter No. Countermeasure Default Suggeste

Value d Setting
• If overvoltage trips occur, gradually
increase this setting by 10 ms and check
the performance.
Torque
• Overvoltage trips when • If response is slow, gradually reduce this
Compensation
accelerating, decelerating, or setting by 2 ms and check the 150 to 750
Primary Delay 150 ms
during sudden speed or load performance. Note: Ensure that C4-02 ≤ ms
Time Constant 2
changes C4-06. When changing C4-06 (Torque
(C4-06)
Compensation Primary Delay Time
Constant 2), increase the value of n2-03
proportionally.
Slip
• If response is slow, gradually decrease the
Compensation
• Poor speed response and setting by 10 ms. 200 ms 100 to 500
Primary Delay
stability • If speed is unstable, gradually increase the <1> ms
Time Constant

Troubleshooting
setting by 10 ms.
(C3-02)
• If speed is too slow, gradually increase the
Slip
setting by 0.1 ms. 1.0
• Poor speed precision Compensation 0.5 to 1.5
• If speed is too fast, gradually decrease the <1>
Gain (C3-01)
setting by 0.1 ms.
• If there is too much motor noise, the
• Motor noise Carrier
carrier frequency is too high.
• If motor hunting and oscillation occur at
7
0 to the
5
• Control motor hunting and Frequency (Swing
low speeds, reduce the carrier frequency. default
oscillation occur at speeds Selection PWM
• The default setting for the carrier setting
below 10 Hz. (C6-02) 1)
frequency depends on the drive capacity
(o2-04) and Drive Duty Selection (C6-01).
• If motor torque and speed response are too
slow, increase the setting. E1-08:
Mid Output • If the motor exhibits excessive instability 12.0 V
• Poor motor torque at low
Voltage A at start-up, reduce the setting. Note: The
speeds
(E1-08) default value is for 200 V class units. <1>
• Poor speed response Initial ±2 V
Minimum Double this value when using a 400 V E1-10:
• Motor instability at motor
Output Voltage class drive. When working with a 2.5 V
start.
(E1-10) relatively light load, increasing this value
too much can create an excessively high of <1>
a torque reference.

<1> Default settings change when the Control Method is changed (A1-02) or a different V/f pattern is selected using
parmaeter E1-03. The default setting shown is for V/f Control.

When using OLV Motor Control, leave the torque compensation gain (C4-01) at its default
setting of 1.00. To increase speed precision during regeneration in OLV Motor Control,
enable slip compensation during regeneration (C3-04 = “1”).

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 179
5.2 Motor Performance Fine Tuning

◆ Motor Hunting and Oscillation Control Parameters

In addition to the parameters discussed in V/f Pattern Selection: E1-03 on page 139, the
following parameters indirectly affect motor hunting and oscillation.
Table 5.3 Parameters that Affect Control Performance in Applications

Name (Parameter No.) Application

Dwell Function Prevents motor speed loss by maintaining the output frequency when working
(b6-01 through b6-04) with heavy loads or when there is powerful backlash on the machine side.
Accel/Decel Time Adjusting accel and decel times will affect the torque presented to the motor
(C1-01 through C1-11) during acceleration or deceleration.
S-Curve Characteristics
Prevents shock at the beginning and end of acceleration and deceleration.
(C2-01 through C2-04)
Jump Frequency
Skips over the resonant frequencies of connected machinery.
(d3-01 through d3-04)
Analog Filter Time Constant
Prevents fluctuation in the analog input signal due to noise.
(H3-13)
• Prevents motor speed loss and overvoltage. Used when the load is too heavy and
also during sudden acceleration/deceleration.
Stall Prevention
• Adjustment is not normally required because Stall Prevention is enabled as a
(L3-01 through L3-06, L3-11)
default. Disable Stall Prevention during deceleration (L3-04 = “0”) when using a
braking resistor.
• Sets the maximum torque for Open Loop Vector Control.
Torque Limits
• Ensure that the drive capacity is greater than the motor capacity when increasing
(L7-01 through L7-04, L7-06,
this setting. Be careful when reducing this value because motor speed loss may
L7-07)
occur with heavy loads.

180 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 5.3 Drive Alarms, Faults, and Errors

5.3 Drive Alarms, Faults, and Errors

◆ Types of Alarms, Faults, and Errors

Check the LED operator for information about possible faults if the drive or motor fails to
operate. Refer to Using the Digital LED Operator on page 91.
If problems occur that are not covered in this manual, contact the nearest Yaskawa
representative with the following information:
• Drive model
• Software version
• Date of purchase
• Description of the problem

Troubleshooting
Table 5.4 contains descriptions of the various types of alarms, faults, and errors that may
occur while operating the drive.
Contact Yaskawa in the event of drive failure.
Table 5.4 Types of Alarms, Faults, and Errors

Type Drive Responses to Alarms, Faults, and Errors 5

• When the drive detects a fault:
• The digital operator displays text that indicates the specific fault and the ALM indicator LED
remains lit until the fault is reset.
• The fault interrupts drive output and the motor coasts to a stop.
Faults
• Depending on the setting, the drive and motor may stop via different methods than listed.
• If a digital output is programmed for fault output (H2- = E), it will close if a fault occurs.
• When the drive detects a fault, it will remain inoperable until that fault has been reset. Refer to
Fault Reset Methods on page 227.
• When the drive detects an alarm or a minor fault:
• The digital operator displays text that indicates the specific alarm or minor fault and the ALM
indicator LED flashes.
Minor Faults and • The motor does not stop.
Alarms • One of the multi-function contact outputs closes if set to be tripped by a minor fault (H2- =
10), but not by an alarm.
• The digital operator displays text indicating a specific alarm and ALM indicator LED flashes.
• Remove the cause of an alarm or minor fault to automatically reset.
• When parameter settings conflict with one another or do not match hardware settings (such as
with an option card), it results in an operation error.
• When the drive detects an operation error:
Operation Errors • The digital operator displays text that indicates the specific error.
• Multi-function contact outputs do not operate.
• When the drive detects an operation error, it will not operate the motor until the error has been
reset. Correct the settings that caused the operation error to reset.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 181
5.3 Drive Alarms, Faults, and Errors

Type Drive Responses to Alarms, Faults, and Errors

• Tuning errors occur while performing Auto-Tuning.
• When the drive detects a tuning error:
• The digital operator displays text indicating the specific error.
Tuning Errors
• Multi-function contact outputs do not operate.
• Motor coasts to stop.
• Remove the cause of the error and repeat the Auto-Tuning process.

◆ Alarm and Error Displays

■ Faults
When the drive detects a fault, the ALM indicator LEDs remain lit without flashing. If the
LEDs flash, the drive has detected a minor fault or alarm. Refer to Minor Faults and
Alarms on page 184 for more information. An overvoltage situation trips both faults and
minor faults, therefore it is important to note whether the LEDs remain lit or if the LEDs
flash.

LED Operator LED Operator

Display Name Page Display Name Page

Option Communication
bUS 187 CPF22 A/D Conversion Error 190
Error
MEMOBUS/Modbus
CE 187 CPF23 PWM Feedback Data Fault 191
Communication Error

CF Control Fault 188 CPF24 Drive Capacity Signal Fault 191

Excessive Speed Deviation

CoF Current Offset Fault 188 dEv 191
(for Simple V/f with PG)

CPF02 A/D Conversion Error 188 EF0 Option Card External Fault 191

EF1
to External Fault
CPF03 PWM Data Fault 188 to 192
(input terminal S1 to S7)
EF7
Drive specification
mismatch during Terminal
CPF06 189 FbH Excessive PID Feedback 192
Board or Control Board
replacement
Terminal Board
CPF07 189 FbL PID Feedback Loss 193
Communication Fault
EEPROM Serial
CPF08 189 GF Ground Fault 193
Communications Fault

CPF11 RAM Fault 189 LF Output Phase Loss 193

182 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 5.3 Drive Alarms, Faults, and Errors

LED Operator Name Page LED Operator Name Page

Display Display

CPF12 FLASH Memory Fault 189 LF2 Output Open Phase 194

Watchdog Circuit
CPF13 189 oC Overcurrent 194
Exception

CPF14 Control Circuit Fault 190 oFA00 Option Card Fault (port A) 195

CPF16 Clock Fault 190 oH Heatsink Overheat 196

CPF17 Timing Fault 190 oH1 Heatsink Overheat 196

PG Disconnect
CPF18 Control Circuit Fault 190 PGo 202
(for Simple V/f with PG)

Troubleshooting
CPF19 Control Circuit Fault 190 rH Dynamic Braking Resistor 202

Dynamic Braking
RAM Fault 190 rr 203
Transistor
Too Many Speed Search
CPF20 FLASH Memory Fault 190 SEr
Restarts
203
or or
CPF21 Watchdog Circuit
Exception
190 STO Pull-Out Detection 203
5
Clock Fault 190 UL3 Undertorque Detection 1 203

Motor Overheat 1 (PTC

oH3 197 UL4 Undertorque Detection 2 204
input)
Motor Overheat 2 (PTC Mechanical Weakening
oH4 197 UL5 204
input) Detection 2

oL1 Motor Overload 197 Uv1 Undervoltage 204

Control Power Supply

oL2 Drive Overload 198 Uv2 205
Undervoltage

oL3 Overtorque Detection 1 199 Uv3 Soft Charge Circuit Fault 205

Overspeed
oL4 Overtorque Detection 2 199 oS 200
(for Simple V/f with PG)
Mechanical Weakening
oL5 199 ov Overvoltage 200
Detection 1

oL7 High Slip Braking OL 199 PF Input Phase Loss 201

oPr Operator Connection Fault 200

Note: If faults CPF11 through CPF19 occur, the LED operator will display or .

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 183
5.3 Drive Alarms, Faults, and Errors

■ Minor Faults and Alarms

When a minor fault or alarm occurs, the ALM LED flashes and the text display shows an
alarm code. A fault has occurred if the text remains lit and does not flash. Refer to Alarm
Detection on page 206. An overvoltage situation, for example, can trigger both faults and
minor faults. It is therefore important to note whether the LEDs remain lit or if the LEDs
flash.
Table 5.5 Minor Fault and Alarm Displays

Minor Fault
LED Operator Display Name Output Page
(H2-†† = 10)

bb Drive Baseblock No output 206

bUS Option Card Communications Error YES 206

CALL Serial Communication Transmission Error YES 207

CE MEMOBUS/Modbus Communication Error YES 207

dEv Excessive Speed Deviation (for Simple V/f with PG) YES 208

dnE Drive Disabled YES 208

EF Run Command Input Error YES 208

EF0 Option Card External Fault YES 209

EF1
to
to External Fault (input terminal S1 to S7) YES 209
EF7

FbH Excessive PID Feedback YES 210

FbL PID Feedback Loss YES 210

Hbb Hardwire Baseblock Signal Input YES 210

HbbF Hardwire Baseblock Signal Input YES 211

SE MEMOBUS/Modbus Test Mode Fault YES

oL5 Mechanical Weakening Detection 1 YES 199

UL5 Mechanical Weakening Detection 2 YES 204

dWAL DriveWorksEZ Alarm YES 191

184 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 5.3 Drive Alarms, Faults, and Errors

Minor Fault
LED Operator Display Name Output Page
(H2-†† = 10)

HCA Current Alarm YES 211

oH Heatsink Overheat YES 211

oH2 Drive Overheat YES 212

oH3 Motor Overheat YES 212

oL3 Overtorque 1 YES 213

oL4 Overtorque 2 YES 213

Troubleshooting
oS Overspeed (for Simple V/f with PG) YES 213

ov Overvoltage YES 213

PASS MEMOBUS/Modbus Test Mode Complete No output 214

PGo PG Disconnect (for Simple V/f with PG) YES 214

5
rUn During Run 2, Motor Switch Command Input YES 214

rUnC Run Command Reset YES 215

UL3 Undertorque 1 YES 215

UL4 Undertorque 2 YES 215

Uv Undervoltage YES 215

■ Operation Errors
Table 5.6 Operation Error Displays

LED Operator Name Page LED Operator Name Page

Display Display

oPE01 Drive kVA Setting Error 217 oPE08 Parameter Selection Error 220

Parameter Setting Range

oPE02 217 oPE09 PID Control Selection Error 220
Error
Multi-Function Input Setting
oPE03 217 oPE10 V/f Data Setting Error 220
Error

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 185
5.3 Drive Alarms, Faults, and Errors

LED Operator LED Operator

Display Name Page Display Name Page

Terminal Board Mismatch Carrier Frequency Setting

oPE04 219 oPE11 221
Error Error
Run Command Selection Pulse Train Monitor
oPE05 219 oPE13 221
Error Selection Error
Multi-Function Analog Input
oPE07 219
Selection Error

■ Auto-Tuning Errors
Table 5.7 Auto-Tuning Error Displays

LED Operator Name Page LED Operator Name Page

Display Display

Er-01 Motor Data Error 222 Er-09 Acceleration Error 223

Er-02 Alarm 222 Er-11 Motor Speed Error 224

Er-03 STOP button Input 222 Er-12 Current Detection Error 224

Line-to-Line Resistance
Er-04 223 End1 Excessive V/f Setting 224
Error
Motor Iron Core Saturation
Er-05 No-Load Current Error 223 End2 224
Coefficient Error

Er-08 Rated Slip Error 223 End3 Rated Current Setting Alarm 225

186 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 5.4 Fault Detection

5.4 Fault Detection

◆ Fault Displays, Causes, and Possible Solutions

Table 5.8 Detailed Fault Displays, Causes, and Possible Solutions

LED Operator Display Fault Name

Option Communication Error
bUS • After establishing initial communication, the connection was lost.
• Only detected when the run command frequency reference is assigned to an
option card.
Cause Possible Solution
No signal received from the PLC.

Troubleshooting
• Check for faulty wiring.
The communication cable is faulty • Correct the wiring.
or a short circuit exists. • Check for loose wiring and short circuits. Repair as needed.
• Check the various options available to minimize the effects of noise.
• Counteract noise in control circuit, main circuit, and ground wiring.
• Ensure that other equipment such as switches or relays do not cause noise and
A communications data error use surge suppressors if required.
occurred due to noise. • Use cables recommended by Yaskawa or another type of shielded line.
Ground the shield on the controller side or on the drive input power side.
5
• Separate all wiring for communications devices from drive input power lines.
Install a noise filter to the input side of the drive input power.
• Replace the option card if there are no problems with the wiring and the error
The option card is damaged.
continues to occur.
• The connector pins on the option card are not properly lined up with the
The option card is not properly
connector pins on the drive.
connected to the drive.
• Reinstall the option card.
LED Operator Display Fault Name
MEMOBUS/Modbus Communication Error
CE
Control data was not received for the CE detection time set to H5-09.
Cause Possible Solution
• Check for faulty wiring.
Faulty communications wiring, or a
• Correct the wiring.
short circuit exists.
• Check for loose wiring and short circuits. Repair as needed.
• Check the various options available to minimize the effects of noise.
• Counteract noise in control circuit, main circuit, and ground wiring.
• Ensure that other equipment such as switches or relays do not cause noise and
A communications data error use surge suppressors if required.
occurred due to noise. • Use Yaskawa-recommended cables, or another type of shielded line. Ground
the shield on the controller side or on the drive input power side.
• Separate all wiring for communications devices from drive input power lines.
Install a noise filter to the input side of the drive input power.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 187
5.4 Fault Detection

LED Operator Display Fault Name

Control Fault
CF A torque limit was reached continuously for three seconds or longer during a
ramp to stop while in Open Loop Vector Control.
Cause Possible Solution
Motor parameters are not set
Check the motor parameter settings and repeat Auto-Tuning.
properly.
Torque limit is too low. Set the torque limit to the most appropriate setting (L7-01 through L7-04).
• Adjust the deceleration time (C1-02, -04, -06, -08).
Load inertia is too big. • Set the frequency to the minimum value and interrupt the run command when
the drive finishes decelerating.
LED Operator Display Fault Name
Current Offset Fault
CoF There is a problem with the current detection circuit or the drive attempted to
start a coasting PM motor.
Cause Possible Solution
While the drive automatically
adjusted the current offset, the Enable Speed Search at start (b3-01 = 1).
calcluated value exceeded the Use the multi-function terminals to execute External Speed Search 1 and 2
allowable setting range. This (H1- . = 61 or 62). NOTE: When using a PM motor, both External Speed
problem may occur when attempting Search 1 and 2 perform the same operation.
to restart a coasting PM motor.
The drive attempted to write
parameter values when the drive
Reinitialize the drive (A1-03).
input power was shut off
(uscommunicaing tions option card).
A/D Conversion Error
CPF02
An A/D conversion error occurred.
Cause Possible Solution
Cycle power to the drive.
Control circuit is damaged.
If the problem continues, replace the drive.
• Check for wiring errors along the control circuit terminals.
Control circuit terminals have • Correct the wiring.
shorted out (+V, AC).
Check the resistance of the speed potentiometer and related wiring.
Control terminal input current has • Check the input current.
exceeded allowable levels. • Reduce the current input to control circuit terminal (+V) to 20 mA.
LED Operator Display Fault Name
PWM Data Error
CPF03
There is a problem with the PWM data.
Cause Possible Solution
Drive hardware is damaged. Replace the drive.

188 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 5.4 Fault Detection

LED Operator Display Fault Name

EEPROM Data Error
CPF06
There is an error in the data saved to EEPROM.
Cause Possible Solution
Cycle power to the drive.
Control circuit is damaged.
If the problem continues, replace the drive.
The drive attempted to write
parameter values when the drive
Reinitialize the drive (A1-03).
input power was shut off
(uscommunicaing tions option card).
LED Operator Display Fault Name
Terminal Board Communications Error
CPF07
A communication error occurred at the terminal board.

Troubleshooting
Cause Possible Solution
There is a fault connection between
the terminal board and control Turn the power off and reconnect the control circuit terminals.
board.
LED Operator Display Fault Name
EEPROM Serial Communication Fault
CPF08
EEPROM communications are not functioning properly. 5
Cause Possible Solution
Terminal board or control board is
Turn the power off and check the control terminal connections.
not connected properly.
LED Operator Display Fault Name

CPF11 RAM Fault

Cause Possible Solution

Hardware is damaged. Replace the drive.
LED Operator Display Fault Name
FLASH Memory Fault
CPF12
Problem with the ROM (FLASH memory).
Cause Possible Solution
Hardware is damaged. Replace the drive.
LED Operator Display Fault Name
Watchdog Circuit Exception
CPF13
Self-diagnostics problem.
Cause Possible Solution
Hardware is damaged. Replace the drive.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 189
5.4 Fault Detection

LED Operator Display Fault Name

Control Circuit Fault
CPF14
CPU error (CPU operates incorrectly due to noise, etc.)
Cause Possible Solution
Hardware is damaged. Replace the drive.
LED Operator Display Fault Name
Clock Fault
CPF16
Standard clock error.
Cause Possible Solution
Hardware is damaged. Replace the drive.
LED Operator Display Fault Name
Timing Fault
CPF17
A timing error occurred during an internal process.
Cause Possible Solution
Hardware is damaged. Replace the drive.
LED Operator Display Fault Name
Control Circuit Fault
CPF18
CPU error (CPU operates incorrectly due to noise, etc.)
Cause Possible Solution
Hardware is damaged. Replace the drive.
LED Operator Display Fault Name
Control Circuit Fault
CPF19
CPU error (CPU operates incorrectly due to noise, etc.)
Cause Possible Solution
Hardware is damaged. Replace the drive.
LED Operator Display Fault Name
One of the following faults occurred: RAM fault, FLASH memory error,
watchdog circuit exception, clock error
or CPF20 • RAM fault.
or CPF21 • FLASH memory error (ROM error).
• Watchdog circuit exception (self-diagnostic error).
• Clock error.
Cause Possible Solution
Hardware is damaged. Replace the drive.
LED Operator Display Fault Name
A/D Conversion Fault
CPF22
A/D conversion error.

190 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 5.4 Fault Detection

Cause Possible Solution

• Cycle power to the drive. Refer to Diagnosing and Resetting Faults on
Control circuit is damaged. page 226.
• If the problem continues, replace the drive.
LED Operator Display Fault Name
PWM Feedback Fault
CPF23
PWM feedback error.
Cause Possible Solution
Hardware is damaged. Replace the drive.
LED Operator Display Fault Name
Drive Capacity Signal Fault
CPF24 Entered a capacity that does not exist.
(Checked when the drive is powered up.)

Troubleshooting
Cause Possible Solution
Hardware is damaged. Replace the drive.
LED Operator Display Fault Name
Speed Deviation (for Simple V/f with PG)
dEv According to the pulse input (RP), the speed deviation is greater than the

Cause
setting in F1-10 for longer than the time set to F1-11.
Possible Solution
5
Load is too heavy. Reduce the load.
Acceleration and deceleration times
Increase the acceleration and deceleration times (C1-01 through C1-08).
are set too short.
The load is locked up. Check the machine.
Parameters are not set appropriately. Check the settings of parameters F1-10 and F1-11.
Motor brake engaged. Ensure the motor brake releases properly.
LED Operator Display Fault Name

dWFL DriveWorksEZ Fault

dWAL DriveWorksEZ Program Error Output

Cause Possible Solution

DriveWorksEZ program output a
• Correct whatever caused the fault to occur.
fault.
LED Operator Display Fault Name
Option Card External Fault
EF0
An external fault condition is present.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 191
5.4 Fault Detection

Cause Possible Solution

An external fault was received from
• Remove the cause of the external fault.
the PLC with F6-03 = 3 “alarm
• Remove the external fault input from the PLC.
only” (the drive continued to run).
Problem with the PLC program. Check the PLC program and correct problems.
LED Operator Display Fault Name
External Fault (input terminal S1)
EF1
External fault at multi-function input terminal S1.
External Fault (input terminal S2)
EF2
External fault at multi-function input terminal S2.
External Fault (input terminal S3)
EF3
External fault at multi-function input terminal S3.
External Fault (input terminal S4)
EF4
External fault at multi-function input terminal S4.
External Fault (input terminal S5)
EF5
External fault at multi-function input terminal S5.
External Fault (input terminal S6)
EF6
External fault at multi-function input terminal S6.
External Fault (input terminal S7)
EF7
External fault at multi-function input terminal S7.
Cause Possible Solution
An external device has tripped an
Remove the cause of the external fault and reset the fault.
alarm function.
• Ensure the signal lines have been connected properly to the terminals
Wiring is incorrect. assigned for external fault detection (H1- = 20 to 2F).
• Reconnect the signal line.
Incorrect setting of multi-function • Check if the unused terminals set for H1- = 20 to 2F (External Fault).
contact inputs. • Change the terminal settings.
LED Operator Display Fault Name
EEPROM Write Error
Err
Data does not match the EEPROM being written to.
Cause Possible Solution

• Press the button.

- • Correct the parameter settings.
• Cycle power to the drive. Refer to Diagnosing and Resetting Faults on
page 226.
LED Operator Display Fault Name
Excessive PID Feedback
FbH PID feedback input is greater than the level set b5-36 for longer than the time
set to b5-37. To enable fault detection, set b5-12 = “2” or “5”.

192 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 5.4 Fault Detection

Cause Possible Solution

Parameters are not set appropriately. Check the settings of parameters b5-36 and b5-37.
Wiring for PID feedback is
Correct the wiring.
incorrect.
There is a problem with the • Check the sensor on the control side.
feedback sensor. • Replace the sensor if damaged.
LED Operator Display Fault Name
PID Feedback Loss
FbL This fault occurs when PID Feedback Loss Detection is programmed to fault
(b5-12 = 2) and the PID Feedback < PID Feedback Loss Detection Level
(b5-13) for the PID Feedback Loss Detection Time (b5-14).
Cause Possible Solution
Parameters are not set appropriately. Check the settings of parameters b5-13 and b5-14.

Troubleshooting
Wiring for PID feedback is
Correct the wiring.
incorrect.
There is a problem with the Check the sensor on the controller side.
feedback sensor. If damaged, replace the sensor.
LED Operator Display Fault Name
Ground Fault
GF • Current shorted to ground exceeded 50% of rated current on output side of the 5
drive.
• Setting L8-09 to 1 enables ground fault detection in models 5.5 kW or larger.
Cause Possible Solution
• Check the insulation resistance of the motor.
Motor insulation is damaged.
• Replace the motor.
• Check the motor cable.
A damaged motor cable is creating a • Remove the short circuit and turn the power back on.
short circuit. • Check the resistance between the cable and the ground terminal .
• Replace the cable.
The leakage current at the drive • Reduce the carrier frequency.
output is too high. • Reduce the amount of stray capacitance.
• The value set exceeds the allowable setting range while the drive
automatically adjusts the current offset (this happens only attempting to
The drive started to run during
restart a PM motor that is coasting to stop).
Current Offset Fault or while
• Enable Speed Search at start (b3-01 = 1).
coasting to a stop.
• Perform Speed Search 1 or 2 (H1-xx = 61 or 62) via one of the external
terminals. Note: Speed Search 1 and 2 are the same when using PM OLV.
Hardware problem. • Replace the drive.
LED Operator Display Fault Name
Output Phase Loss
LF • Phase loss on the output side of the drive.
• Phase Loss Detection is enabled when L8-07 is set to “1” or “2”.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 193
5.4 Fault Detection

Cause Possible Solution

• Check for wiring errors and ensure the output cable is connected properly.
The output cable is disconnected.
• Correct the wiring.
• Check the resistance between motor lines.
The motor winding is damaged.
• Replace the motor if the winding is damaged.
• Apply the tightening torque specified in this manual to fasten the terminals.
The output terminal is loose.
Refer to Wire Size and Torque Specifications on page 72.
The motor being used is less than
Check the drive and motor capacities.
5% of the drive rated current.
An output transistor is damaged. Replace the drive.
A single phase motor is being used. The drive being used cannot operate a single phase motor.
LED Operator Display Fault Name
Output current imbalance
LF2
One or more of the phases in the output current is lost.
Cause Possible Solution
Phase loss has occurred on the • Check for faulty wiring or poor connections on the output side of the drive.
output side of the drive. • Correct the wiring.
Terminal wires on the output side of Apply the tightening torque specified in this manual to fasten the terminals.
the drive are loose. Refer to Wire Size and Torque Specifications on page 72.
No signal displays from the gate
Replace the drive. Contact Yaskawa for assistance.
driver board.
• Measure the line-to-line resistance for each motor phase. Ensure all values are
Motor impedance or motor phases
the same.
are uneven.
• Replace the motor. Contact Yaskawa for assistance.
LED Operator Display Fault Name
Overcurrent
oC Drive sensors have detected an output current greater than the specified
overcurrent level.
Cause Possible Solution
The motor has been damaged due to
Check the insulation resistance.
overheating or the motor insulation
Replace the motor.
is damaged.
• Check the motor cables.
One of the motor cables has shorted • Remove the short circuit and power the drive back up.
out or there is a grounding problem. • Check the resistance between the motor cables and the ground terminal .
• Replace damaged cables.
• Measure the current flowing into the motor.
• Replace the drive with a larger capacity unit if the current value exceeds the
rated current of the drive.
The load is too heavy.
• Determine if there is sudden fluctuation in the current level.
• Reduce the load to avoid sudden changes in the current level or switch to a
larger drive.

194 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 5.4 Fault Detection

• Calculate the torque needed during acceleration relative to the load inertia and
the specified acceleration time.
The acceleration or deceleration • If the right amount of torque cannot be set, make the following changes:
times are too short. • Increase the acceleration time (C1-01, -03, -05, -07)
• Increase the S-curve characteristics (C2-01 through C2-04)
• Increase the capacity of the drive.
The drive is attempting to operate a • Check the motor capacity.
specialized motor or a motor larger • Ensure that the rated capacity of the drive is greater than or equal to the
than the maximum size allowed. capacity rating found on the motor nameplate.
Magnetic contactor (MC) on the
Set up the operation sequence so that the MC is not tripped while the drive is
output side of the drive has turned
outputting current.
on or off.
• Check the ratios between the voltage and frequency.
V/f setting is not operating as • Set parameter E1-04 through E1-10 appropriately. Set E3-04 through E3-10
expected. when using a second motor.

Troubleshooting
• Lower the voltage if it is too high relative to the frequency.
• Check the amount of torque compensation.
Excessive torque compensation. • Reduce the torque compensation gain (C4-01) until there is no speed loss and
less current.
• Review the possible solutions provided for handling noise interference.
Drive fails to operate properly due to
• Review the section on handling noise interference and check the control
noise interference.
circuit lines, main circuit lines and ground wiring.
• Check if fault occurs simultaneously to overexcitation function operation. 5
Overexcitation gain is set too high. • Consider motor flux saturation and reduce the value of n3-13 (Overexcitation
Deceleration Gain).
• Enable Speed Search at start (b3-01 = “1”).
Run command applied while motor
• Program the Speed Search command input through one of the multi-function
was coasting.
contact input terminals (H1- = “61” or “62”).
The wrong motor code has been
entered for PM Open Loop Vector Enter the correct motor code to E5-01 to indicate that a PM motor is connected.
(Yaskawa motors only).
• Check which motor control method the drive is set to (A1-02).
The motor control method and
• For IM motors, set A1-02 = “0” or “2”.
motor do not match.
• For PM motors, set A1-02 = “5”.
The motor cable is too long. Use a larger drive.
LED Operator Display Fault Name
Option Card Fault (Port A)
oFA00
The option card is incompatible with the drive.
Cause Possible Solution
The option card is incompatible with
Use a compatible option card.
the drive.
LED Operator Display Fault Name
Option Card Fault (Port A)
oFA01
Replace the option card.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 195
5.4 Fault Detection

Cause Possible Solution

The option card is not connected
Turn the power off and reconnect the option card.
properly to the drive.
LED Operator Display Fault Name
Option Card Fault (port A)
oFA03
Option card self-diagnostic error
Option Card Fault (port A)
oFA04
An error occurred attempting to write to the option card memory.
Option Card Fault (port A)
thru oFA30 thru
oFA43 Communication ID error

Cause Possible Solution

Option card or hardware is damaged. Replace the option card. Contact Yaskawa for consulation.
LED Operator Display Fault Name
Heatsink Overheat
oH The temperature of the heatsink exceeded the value set to L8-02 (90-100°C).
Default value for L8-02 is determined by drive capacity (o2-04).
Cause Possible Solution
• Check the temperature surrounding the drive. Verify temperature is within
drive specifications.
Surrounding temperature is too high. • Improve the air circulation within the enclosure panel.
• Install a fan or air conditioner to cool the surrounding area.
• Remove anything near the drive that might be producing excessive heat.
• Measure the output current.
Load is too heavy. • Decrease the load.
• Lower the carrier frequency (C6-02).
• Replace the cooling fan. Refer to Cooling Fan Replacement on page 254.
Internal cooling fan is stopped. • After replacing the drive, reset the cooling fan maintenance parameter
(o4-03 = “0”).
LED Operator Display Fault Name
Overheat 1 (Heatsink Overheat)
oH1 The temperature of the heatsink has exceeded the value set to L8-02
(100-110°C). Default value for L8-02 is determined by drive capacity (o2-04).
Cause Possible Solution
• Check the temperature surrounding the drive.
• Improve the air circulation within the enclosure panel.
Surrounding temperature is too hot.
• Install a fan or air conditioner to cool the surrounding area.
• Remove anything near the drive that might be producing excessive heat.
• Measure the output current.
Load is too heavy. • Reduce the load.
• Lower the carrier frequency (C6-02).

196 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 5.4 Fault Detection

• Check the maintenance time for the cooling fan (U4-04).

The internal cooling fan has reached
• If U4-04 exceeds 90%, replace the cooling fan. Refer to Cooling Fan
its performance life or has
Replacement on page 254.
malfunctioned.
• After replacing fan, reset the fan maintenance time (o4-03 = “0”).
Current flowing to control circuit
• Check tCheck the current level of the terminal.
terminal +V exceeded the tolerance
• Set the current to the control circuit terminal to be 20 mA or less.
level.
LED Operator Display Fault Name
Motor Overheat Alarm (PTC Input)
oH3 • The motor overheat signal to analog input terminal A1 or A2 exceeded the
alarm detection level.
• Detection requires multi-function analog input H3-02 or H3-10 be set to “E”.
Cause Possible Solution
• Check the size of the load, the accel/decel times and the cycle times.

Troubleshooting
• Decrease the load.
• Increase the acceleration and deceleration times (C1-01 through C1-08).
• Adjust the preset V/f pattern (E1-04 through E1-10). This will mainly involve
reducing E1-08 and E1-10.
Motor has overheated • Be careful not to lower E1-08 and E1-10 excessively, as this reduces load
tolerance at low speeds.
• Check the motor-rated current.
• Enter the motor-rated current as indicated on the motor nameplate (E2-01). 5
• Ensure the motor cooling system is operating normally.
• Repair or replace the motor cooling system.
LED Operator Display Fault Name
Motor Overheat Fault (PTC Input)
oH4 • The motor overheat signal to analog input terminal A1 or A2 exceeded the
alarm detection level.
• Detection requires that multi-function analog input H3-02 or H3-10 = “E”.
Cause Possible Solution
• Check the size of the load, the accel/decel times and the cycle times.
• Decrease the load.
• Increase the acceleration and deceleration times (C1-01 through C1-08).
• Adjust the preset V/f pattern (E1-04 through E1-10). This will mainly involve
reducing E1-08 and E1-10.Be careful not to lower E1-08 and E1-10
Motor has overheated.
excessively because this reduces load tolerance at low speeds
• Check the motor-rated current.
• Enter the motor-rated current as indicated on the motor nameplate (E2-01).
• Ensure the motor cooling system is operating normally.
• Repair or replace the motor cooling system.
LED Operator Display Fault Name
Motor Overload
oL1
The electrothermal sensor tripped overload protection.
Cause Possible Solution

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 197
5.4 Fault Detection

Load is too heavy. Reduce the load.

Cycle times are too short during
Increase the acceleration and deceleration times (C1-01 through C1-08).
acceleration and deceleration.
• Drive overloaded at low speeds.
• Reduce the load.
• Overload may occur at low speeds
• Increase the speed.
when using a general-purpose
• If the drive is supposed to operate at low speeds, either increase the motor
motor, even if operating within the
capacity or use a motor specifically designed to operate with the drive.
rated current limitation.
Although a special type of motor is
being used, the motor protection
Set L1-01 = “2”.
selection is set for a general-purpose
motor (L1-01 = 1).
• Adjust the user set V/f patterns (E1-04 through E1-10). Parameters E1-08 and
Voltage is too high for the V/f E1-10 may need to be reduced.
characteristics. • If E1-08 and E1-10 are set too high, there may be very little load tolerance at
low speed.
The wrong motor-rated current is set • Check the motor-rated current.
to E2-01. • Enter the value written on the motor nameplate to parameter E2-01.
The maximum frequency for the • Check the rated frequency indicated on the motor nameplate.
drive input power is set too low. • Enter the rated frequency to E1-06 (Base Frequency).
Multiple motors are running off the Disable the Motor Protection function (L1-01 = “0”) and install a thermal relay
same drive. to each motor.
The electrical thermal protection • Check the motor characteristics.
characteristics and motor overload • Correct the value set to L1-01 (Motor Protection Function).
characteristics do not match. • Install an external thermal relay.
The electrical thermal relay is • Check the current rating listed on the motor nameplate.
operating at the wrong level. • Check the value set for the motor-rated current (E2-01).
Cause Possible Solution
• Overexcitation is a potential serious danger to the motor.
• Reduce the excitation deceleration gain (n3-13).
Overexcitation current is enabled.
• Set L3-04 (Stall Prevention during Deceleration) to a value other than 4.
• Disable overexcitation (n3-23 = “0”).
• Check values set to Speed Search related parameters.
Speed Search related parameters are • Adjust the Speed Search current and Speed Search deceleration times (b3-02
not set to the proper values. and b3-03 respectively).
• After Auto-Tuning, enable Speed Estimation Type Search (b3-24 = “1”).
Output current fluctuation due to
Check the power supply for phase loss.
input phase loss.
LED Operator Display Fault Name
Drive Overload
oL2
The thermal sensor of the drive triggered overload protection.
Cause Possible Solution
Load is too heavy. Reduce the load.

198 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 5.4 Fault Detection

Cycle times are too short during Increase the settings for the acceleration and deceleration times (C1-01
acceleration and deceleration. through C1-08).
• Adjust the preset V/f pattern (E1-04 through E1-10). This will mainly involve
Voltage is too high for the V/f reducing E1-08 and E1-10.
characteristics. • Be careful not to lower E1-08 and E1-10 excessively because this reduces
load tolerance at low speeds.
Drive capacity is too small. Replace the drive with a larger model.
• Reduce the load when operating at low speeds.
Overload occurred when operating
• Replace the drive with a model that is one frame size larger.
at low speeds.
• Lower the carrier frequency (C6-02).
Reduce the torque compensation gain (C4-01) until there is no speed loss but
Excessive torque compensation.
less current.
• Check the settings for all Speed Search related parameters.
• Adjust the current used during Speed Search and the Speed Search
Speed Search related parameters are

Troubleshooting
deceleration time (b3-03 and b3-02 respectively).
not set correctly.
• After Auto-Tuning the drive, enable the Speed Search Estimation Type
(b3-24 = “1”).
Output current fluctuation due to
Check the power supply for phase loss.
input phase loss.
LED Operator Display Fault Name
Overtorque Detection 1
oL3 The current has exceeded the value set for torque detection (L6-02) for longer
5
than the allowable time (L6-03).
Cause Possible Solution
Parameter settings are not
Check the settings of parameters L6-02 and L6-03.
appropriate for the type of load.
There is a fault on the machine side Check the status of the load.
(e.g., the machine is locked up). Remove the cause of the fault.
LED Operator Display Fault Name
Overtorque Detection 2
oL4 The current has exceeded the value set for Overtorque Detection 2 (L6-05) for
longer than the allowable time (L6-06).
Cause Possible Solution
Parameter settings are not
Check the settings of parameters L6-05 and L6-06.
appropriate for the type of load.
There is a fault on the machine side Check the status of the load.
(e.g., the machine is locked up). Remove the cause of the fault.
LED Operator Display Fault Name
High-Slip Braking OL
oL7 The output frequency stayed constant for longer than the time set in n3-04
during High-slip Braking.
Cause Possible Solution

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 199
5.4 Fault Detection

Excessive load inertia.

• Reduce deceleration times using parameters C1-02, -04, -06 and -08 in
Motor is driven by the load.
applications that do not use High-slip Braking.
Something on the load side is • Use a braking resistor to shorten deceleration time.
restricting deceleration.
• Increase parameter n3-04 (High-slip Braking Overload Time).
The overload time during High-slip
• Install a thermal relay and increase the parameter setting of n3-04 to the
Braking during is too short.
maximum value.
LED Operator Display Fault Name
Digital Operator Connection Fault
• The LCD operator has been disconnected from the drive. Note: An oPr fault
oPr will occur when all of the following conditions are true:
• Output is interrupted when the operator is disconnected (o2-06 = 1).
• The run command is assigned to the LCD operator (b1-02 = 0 and LOCAL
has been selected).
Cause Possible Solution
• Check the connection between the LCD operator and the drive.
LCD operator is not properly • Replace the cable if damaged.
connected to the drive. • Turn off the drive input power and disconnect the LCD operator. Next
reconnect the operator and turn the drive input power back on.
LED Operator Display Fault Name
Overspeed (Simple V/f with PG)
oS
Pulse input (RP) indicates that motor speed feedback exceeded F1-08 setting.
Cause Possible Solution
• Adjust the gain by using the pulse train input parameters
Overshoot or undershoot is (H6-02 through H6-05).
occurring. • Increase the settings for C5-01 (Speed Control Proportional Gain 1) and
reduce C5-02 (Speed Control Integral Time 1).
Set the H6-02 (Pulse Train Input Scaling) = 100%, the number of pulses during
Incorrect PG pulse settings.
maximum motor revolutions.
Check the setting for the overspeed detection level and the overspeed detection
Inappropriate parameter settings.
time (F1-08 and F1-09).
LED Operator Display Fault Name
Overvoltage
ov Voltage in the DC bus has exceeded the overvoltage detection level.
For 200 V class: approximately 410 V
For 400 V class: approximately 820 V (740 V when E1-01 is less than 400)
Cause Possible Solution
• Increase the deceleration time (C1-02, -04, -06, -08).
Deceleration time is too short and
• Install a braking resistor or a dynamic braking resistor unit.
regenerative energy flows from the
• Enable stall prevention during deceleration (L3-04 = “1”). Stall prevention is
motor into the drive.
enabled as the default setting.

200 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 5.4 Fault Detection

• Check if sudden drive acceleration triggers an overvoltage alarm.

Acceleration time is too short. • Increase the acceleration time.
• Use longer S-curve acceleration and deceleration times.
The braking torque was too high, causing regenerative energy to charge the DC
Excessive braking load.
bus. Reduce the braking torque, use a braking option, or lengthen decel time.
Surge voltage entering from the Install a DC reactor. Note: Voltage surge can result from thyristor convertor
drive input power. and phase advancing capacitor using same drive main input power supply.
Ground fault in the output circuit
• Check the motor wiring for ground faults.
causing the DC bus capacitor to
• Correct grounding shorts and turn the power back on.
overcharge.
• Check the settings for Speed Search related parameters.
Improper Setting of Speed Search
• Enable Speed Search Retry function (b3-19 greater than or equal to 1 to 10).
related parameters.
• Adjust the current level during Speed Search and the deceleration time (b3-02
(Includes Speed Search after a
and b3-03 respectively).
momentary power loss and after a
• Perform Line-to-Line Resistance Auto-Tuning and then enable Speed

Troubleshooting
fault restart.)
Estimation Type Speed Search (b3-24 = “1”).
Excessive regeneration when Enable the Overvoltage Suppression function (L3-11 = “1”).
overshoot occurs after acceleration. Lengthen the S-curve at acceleration end.
Drive input power voltage is too • Check the voltage.
high. • Lower drive input power voltage within the limits listed in the specifications.
The dynamic braking transistor is
damaged.
Replace the drive.
5
The braking transistor is wired • Check braking transistor wiring for errors.
incorrectly. • Properly rewire the braking resistor device.
• Review the list of possible solutions provided for controlling noise.
Drive fails to operate properly due to
• Review the section on handling noise interference and check the control
noise interference.
circuit lines, main circuit lines and ground wiring.
• Check the load inertia settings when using KEB, overvoltage suppression or
Load inertia has been set incorrectly. Stall Prevention during deceleration.
• Adjust L3-25 (Load Inertia Ratio) in accordance with the load.
Braking function is being used in
Connect a braking resistor.
PM Open Loop Vector Control.
• Adjust the parameters that control hunting.
• Set the hunting prevention gain (n1-02).
Motor hunting occurs. • Adjust the AFR time constant (n2-02 and n2-03) when in OLV Control.
• Use parameters n8-45 (PM Speed Feedback Detection Suppression Gain) and
n8-47 (Pull-In Current Compensation Time Constant).
LED Operator Display Fault Name
Input Phase Loss
PF Drive input power has an open phase or has a large imbalance of voltage
between phases. Detected when L8-05 = 1 (enabled).
Cause Possible Solution
There is phase loss in the drive input • Check for wiring errors in the main circuit drive input power.
power. • Correct the wiring.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 201
5.4 Fault Detection

• Ensure the terminals are tightened properly.

There is loose wiring in the drive
• Apply the tightening torque specified in this manual to fasten the terminals.
input power terminals.
Refer to Wire Gauges and Tightening Torque on page 63
• Check the voltage from the drive input power.
• Review the possible solutions for stabilizing the drive input power.
There is excessive fluctuation in the
• Disable Input Phase Loss Detection (L8-05 = “0”). PF is detected if DC bus
drive input power voltage.
ripple is too high. If it is disabled, there is no fault but the ripple is still too
high, thereby the capacitors are stressed more and lose lifetime.
There is poor balance between
• Stabilize drive input power or disable phase loss detection.
voltage phases.
Cause Possible Solution
• Check the maintenance time for the capacitors (U4-05).
• Replace the drive if U4-05 is greater than 90%.
• Check for anything wrong with the drive input power.
The main circuit capacitors are • If nothing is wrong with the drive input power, try the following solutions if
worn. the alarm continues:
• Disable Input Phase Loss Protection selection (L8-05 = “0”). PF is detected if
DC bus ripple is too high. If it is disabled, there is no fault but the ripple is still
too high, thereby the capacitors are stressed more and lose lifetime.
• Replace the drive.
LED Operator Display Fault Name
PG Disconnect (for Simple V/f with PG)
PGo
No PG pulses are received for longer than the time set to F1-14.
Cause Possible Solution
Pulse input (RP) is disconnected. Reconnect the pulse input (RP).
Pulse input (RP) wiring is wrong. Correct the wiring.
Motor brake engaged. Ensure the motor brake releases properly.
LED Operator Display Fault Name
Braking Resistor Overheat
rH Braking resistor protection was triggered.
Fault detection is enabled when L8-01 = 1 (disabled as a default).
Cause Possible Solution
• Check the load, deceleration time and speed.
Deceleration time is too short and • Reduce the load.
excessive regenerative energy is • Increase the acceleration and deceleration times (C1-01 through C1-08).
flowing back into the drive. • Replace the braking option with a larger device that can handle the power that
is discharged.
Recalculate braking load and braking power. Then try reducing the braking
Excessive braking inertia.
load and checking the braking resistor settings and improve braking capacity.
The proper braking resistor has not • Check the specifications and conditions for the braking resistor device.
been installed. • Select the optimal braking resistor.

202 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 5.4 Fault Detection

Note: The magnitude of the braking load trips the braking resistor overheat alarm, NOT the surface temperature.
Using the braking resistor more frequently than its rating trips the alarm even when the braking resistor surface is not
very hot.
LED Operator Display Fault Name
Dynamic Braking Transistor
rr
The built-in dynamic braking transistor failed.
Cause Possible Solution
The braking transistor is damaged. • Cycle power to the drive and check if the fault reoccurs. Refer to Diagnosing
and Resetting Faults on page 226.
The control circuit is damaged. • Replace the drive if the fault continues.
LED Operator Display Fault Name
Too Many Speed Search Restarts
SEr
The number of speed search restarts exceeded the number set to b3-19.

Troubleshooting
Cause Possible Solution
• Reduce the detection compensation gain during Speed Search (b3-10).
Speed Search parameters are set to • Increase the current level when attempting Speed Search (b3-17).
the wrong values. • Increase the detection time during Speed Search (b3-18).
• Repeat Auto-Tuning.
The motor is coasting in the opposite
Enable Bi-directional Speed Search (b3-14 = “1”).
direction of the run command.
LED Operator Display Fault Name
5
Pull-Out Detection
STO
Motor pull-out has occurred.
Cause Possible Solution
• Enter the correct motor code for the PM being used into E5-01.
The wrong motor code has been set
• For special-purpose motors, enter the correct data to all E5 parameters
(Yaskawa motors only).
according to the Test Report provided for the motor.
• Increase the value set to n8-55 (Load Inertia for PM).
• Increase the value set to n8-51 (Pull-In Current during Accel/Decel for PM).
Load is too heavy.
• Reduce the load.
• Increase the motor or drive capacity.
Load inertia is too heavy. Increase n8-55 (Load Inertia for PM).
Acceleration and deceleration times • Increase the acceleration and deceleration times (C1-01 through C1-08).
are too short. • Increase the S-curve acceleration and deceleration times (C2-01).
LED Operator Display Fault Name
Undervoltage Detection 1
UL3 The current has fallen below the minimum value set for torque detection
(L6-02) for longer than the allowable time (L6-03).
Cause Possible Solution
Parameter settings are not
Check the settings of parameters L6-02 and L6-03.
appropriate for the type of load.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 203
5.4 Fault Detection

There is a fault on the machine side. Check the load for any problems.
LED Operator Display Fault Name
Undertorque Detection 2
UL4 The current has fallen below the minimum value set for torque detection
(L6-05) for longer than the allowable time (L6-06).
Cause Possible Solution
Parameter settings are not
Check the settings of parameters L6-05 and L6-06.
appropriate for the type of load.
There is a fault on the machine side. Check the load for any problems.
LED Operator Display Fault Name
Mechanical Weakening Detection 2
UL5
The operation conditions matched the conditions set to L6-08.
Cause Possible Solution
Undertorque was detected and
matched the condition of mechanical
Check the load side for any problems.
loss detection operation selection
(L6-08).
LED Operator Display Fault Name
DC Bus Undervoltage
One of the following conditions occurred while the drive was stopped:
• Voltage in the DC bus fell below the undervoltage detection level (L2-05).
Uv1 • For 200 V class: approximately 190 V (160 V for single phase drives)
• For 400 V class: approximately 380 V (350 V when E1-01 is less then 400)
The fault is output only if L2-01 = 0 or L2-01 = 1 and the DC bus voltage is
under L1-05 for longer than L2-02.
Cause Possible Solution
• The main circuit drive input power is wired incorrectly.
Input power phase loss.
• Correct the wiring.
• Ensure there are no loose terminals.
One of the drive input power wiring
• Apply the tightening torque specified in this manual to fasten the terminals.
terminals is loose.
Refer to Wire Size and Torque Specifications on page 72
There is a problem with the voltage • Check the voltage.
from the drive input power. • Correct the voltage to within range listed in drive input power specifications.
The power has been interrupted. Correct the drive input power.
Drive internal circuitry has become • Check the maintenance time for the capacitors (U4-05).
worn. • Replace the drive if U4-05 exceeds 90%.
The drive input power transformer is
not large enough and voltage drops Check the capacity of the drive input power transformer.
after switching on power.
Air inside the drive is too hot. Check the drive’s internal temperature.
Problem with the CHARGE
Replace the drive.
indicator.

204 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 5.4 Fault Detection

LED Operator Display Fault Name

Control Power Supply Voltage Fault
Uv2
Voltage is too low for the control drive input power.
Cause Possible Solution
L2-02 changed from its default
value in drive that is 7.5 kW or Correct parameter L2-02 setting or install optional Momentary Power Loss
smaller without installing a Ride-Thru unit.
Momentary Power Loss Ride-Thru.
The wiring for the control power • Cycle power to the drive. Check if the fault reoccurs.
supply is damaged. • Replace the drive if the fault continues to occur.
• Cycle power to the drive. Check if the fault reoccurs.
Internal circuitry is damaged.
• Replace the drive if the fault continues to occur.
LED Operator Display Fault Name

Troubleshooting
Undervoltage 3 (Inrush Prevention Circuit Fault)
Uv3
The inrush prevention circuit has failed.
Cause Possible Solution
• Cycle power to the drive. Check if the fault reoccurs.
• Replace the drive if the fault continues to occur.
The contactor on the inrush
• Check monitor U4-06 for the performance life of the inrush prevention
prevention circuit is damaged.
circuit.
• Replace the drive if U4-06 exceeds 90%. 5

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 205
5.5 Alarm Detection

5.5 Alarm Detection

Alarms are drive protection functions that do not operate the fault contact. The drive will
return to original status when the cause of the alarm has been removed.
During an alarm condition, the Digital Operator display flashes and an alarm output is
generated at the multi-function outputs (H2-01 to H2-03), if programmed.
Investigate the cause of the alarm and refer to Table 5.9 for the appropriate action.

◆ Alarm Codes, Causes, and Possible Solutions

Table 5.9 Alarm Codes, Causes, and Possible Solutions

LED Operator Display Minor Fault Name

Baseblock
bb
Drive output interrupted as indicated by an external baseblock signal.
Minor Fault (H2-
Cause Possible Solutions
†† = 10)
External baseblock signal
entered via multi-function Check external sequence and baseblock signal input timing. No output
input terminal (S1 to S7).
LED Operator Display Minor Fault Name
Option Communication Error
bUS • After initial communication was established, the connection was lost.
• Assign a run command frequency reference to the option card.
Minor Fault (H2-
Cause Possible Solutions
†† = 10)
Connection is broken or • Check for faulty wiring.
master controller stopped • Correct the wiring. YES
communicating. • Repair ground wiring or disconnected cables.
If there are no problems with the wiring and the fault continues
Option card is damaged. YES
to occur, replace the option card.
The option card is not • The connector pins on the option card are not properly lined up
properly connected to the with the connector pins on the drive. YES
drive. • Reinstall the option card.

206 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 5.5 Alarm Detection

• Check options available to minimize the effects of noise.

• Take steps to counteract noise in the control circuit wiring,
main circuit lines and ground wiring.
• Try to reduce noise on the controller side.
• Use surge absorbers on magnetic contactors or other equipment
A data error occurred due to causing the disturbance.
YES
noise. • Use cables recommended by Yaskawa, or another type of
shielded line. The shield should be grounded on the controller
side or on the drive input power side.
• All wiring for communications devices should be separated
from drive input power lines. Install a noise filter to the input
side of the drive input power.
LED Operator Display Minor Fault Name
Serial Communication Transmission Error
CALL
Communication has not yet been established.

Troubleshooting
Minor Fault (H2-
Cause Possible Solutions
†† = 10)
Communications wiring is
• Check for wiring errors.
faulty, there is a short circuit,
• Correct the wiring. YES
or something is not connected
• Remove and ground shorts and reconnect loose wires.
properly.
Programming error on the
master side.
Check communications at start-up and correct programming
errors.
YES 5
Communications circuitry is • Perform a self-diagnostics check.
YES
damaged. • Replace the drive if the fault continues to occurs.
The terminal slave drive must have the internal terminal
Terminal resistance setting is resistance switch set correctly. Place DIP switch S2 to the ON
YES
incorrect. position. Refer to MEMOBUS/Modbus Switch Settings on
page 407.
LED Operator Display Minor Fault Name
MEMOBUS/Modbus Communication Error
CE
Control data was not received correctly for two seconds.
Minor Fault (H2-
Cause Possible Solutions
†† = 10)
• Check options available to minimize the effects of noise.
• Counteract noise in the control circuit wiring, main circuit lines
and ground wiring.
• Reduce noise on the controller side.
• Use surge absorbers on magnetic contactors or other equipment
A data error occurred due to causing the disturbance.
YES
noise. • Use cables recommended by Yaskawa or another type of
shielded line. The shield should be grounded on the controller
side or on the drive input power side.
• Separate all wiring for communications devices from drive
input power lines. Install a noise filter to the input side of the
drive input power.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 207
5.5 Alarm Detection

• Check the H5 parameter settings as well as the protocol setting

Communication protocol is
in the controller. YES
incompatible.
• Ensure settings are compatible.
The CE detection time
(H5-09) is set shorter than the • Check the PLC.
time required for a • Change the software settings in the PLC. YES
communication cycle to take • Set a longer CE detection time (H5-09).
place.
Incompatible PLC software
• Check the PLC.
settings or there is a hardware YES
• Remove the cause of the error on the controller side.
problem.
Communications cable is • Check the connector for a signal through the cable.
YES
disconnected or damaged. • Replace the communications cable.
LED Operator Display Minor Fault Name
Speed Deviation (for Simple V/f with PG)
dEv According to the pulse input (RP), the speed deviation is greater than the setting in
F1-10 for a time longer than the setting in F1-11.
Minor Fault
Cause Possible Solutions Output
(H2-†† = 10)
Load is too heavy Reduce the load. YES
Acceleration and deceleration Increase the acceleration and deceleration times (C1-01 through
YES
times are set too short. C1-08).
The load is locked up. Check the machine. YES
Parameter settings are
Check the settings of parameters F1-10 and F1-11. YES
inappropriate.
The motor brake engaged. Ensure the brake releases properly. YES
LED Operator Display Minor Fault Name

dnE Drive Disabled

Minor Fault
Cause Possible Solutions Output
(H2-†† = 10)
“Drive Enable” is set to a
multi-function contact input
Check the operation sequence. YES
(H1- = 6A) and that
signal was switched off.
LED Operator Display Minor Fault Name
Forward/Reverse Run Command Input Error
EF
Both forward run and reverse run closed simultaneously for over 0.5 s.
Minor Fault
Cause Possible Solutions Output
(H2-†† = 10)

208 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 5.5 Alarm Detection

Check the forward and reverse command sequence and correct

Sequence error the problem. YES
Note: When minor fault EF detected, motor ramps to stop.
LED Operator Display Minor Fault Name
Option Card External Fault
EF0
An external fault condition is present.
Minor Fault
Cause Possible Solutions Output
(H2-†† = 10)
An external fault was
received from the PLC with
• Remove the cause of the external fault.
F6-03 = 3 (causing the drive YES
• Remove the external fault input from the PLC.
to continue running when an
external fault occurs).

Troubleshooting
There is a problem with the
Check the PLC program and correct problems. YES
PLC program.
LED Operator Display Minor Fault Name
External fault (input terminal S1)
EF1
External fault at multi-function input terminal S1.
External fault (input terminal S2)
EF2
External fault at multi-function input terminal S2. 5
External fault (input terminal S3)
EF3
External fault at multi-function input terminal S3.
External fault (input terminal S4)
EF4
External fault at multi-function input terminal S4.
LED Operator Display Minor Fault Name
External fault (input terminal S5)
EF5
External fault at multi-function input terminal S5.
External fault (input terminal S6)
EF6
External fault at multi-function input terminal S6.
External fault (input terminal S7)
EF7
External fault at multi-function input terminal S7.
Minor Fault
Cause Possible Solutions Output
(H2-†† = 10)
An external device has Remove the cause of the external fault and reset the
YES
tripped an alarm function. multi-function input value.
• Ensure the signal lines have been connected properly to the
terminals assigned for external fault detection
Wiring is incorrect. YES
(H1- = 20 to 2F).
• Reconnect the signal line.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 209
5.5 Alarm Detection

• Check if the unused terminals have been set for

Multi-function contact inputs
H1- = 20 to 2F (External Fault). YES
are set incorrectly.
• Change the terminal settings.
LED Operator Display Minor Fault Name
Excessive PID Feedback
FbH The PID feedback input is higher than the level set in b5-36 for longer than the time
set in b5-37, and b5-12 is set to 1 or 4.
Minor Fault
Cause Possible Solutions Output
(H2-†† = 10)
Parameters settings for b5-36
Check parameters b5-36 and b5-37. YES
and b5-37 are incorrect.
PID feedback wiring is faulty. Correct the wiring. YES
Feedback sensor has
Check the sensor and replace it if damaged. YES
malfunctioned.
Feedback input circuit is
Replace the drive. YES
damaged.
LED Operator Display Minor Fault Name
PID Feedback Loss
FbL The PID feedback input is lower than the level set in b5-13 for longer than the time
set in b5-14, and b5-12 is set to 1 or 4.
Minor Fault
Cause Possible Solutions Output
(H2-†† = 10)
Parameters settings for b5-13
Check parameters b5-13 and b5-14. YES
and b5-14 are incorrect.
PID feedback wiring is faulty. Correct the wiring. YES
Feedback sensor has
Check the sensor and replace it if damaged. YES
malfunctioned.
Feedback input circuit is
Replace the drive. YES
damaged.
LED Operator Display Minor Fault Name
Hardwire Baseblock Signal Input
Hbb
Hardwire Baseblock input signal open.
Minor Fault
Cause Possible Solutions Output
(H2-†† = 10)
Internally, both Hardwire
Baseblock channels are Replace the drive. YES
broken.
There is no signal at terminal Check the wiring of terminal H1.
YES
H1. Check if the PLC signal is set correctly.

210 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 5.5 Alarm Detection

LED Operator Display Minor Fault Name

Hardwire Baseblock Signal Input
HbbF
One of the baseblock channels is damaged.
Minor Fault
Cause Possible Solutions Output
(H2-†† = 10)
One of the baseblock
Replace the drive. YES
channels is faulty.
LED Operator Display Minor Fault Name
Current Alarm
HCA
Drive current exceeded overcurrent warning level (150% of the rated current).
Minor Fault
Cause Possible Solutions Output

Troubleshooting
(H2-†† = 10)
• Measure the current flowing through the motor.
Load is too heavy. YES
• Reduce the load or increase the capacity of the drive.
• Calculate the torque required during acceleration and for the
inertia moment.
• If the torque level is not right for the load, take the following
Acceleration and deceleration
steps: YES
times are too short.
• Increase the acceleration and deceleration times 5
(C1-01 through C1-08).
• Increase the capacity of the drive.
A special-purpose motor is
being used, or the drive is • Check the motor capacity.
attempting to run a motor • Use a motor appropriate for the drive. Ensure the motor is YES
greater than the maximum within the allowable capacity range.
allowable capacity.
The current level increased
due to Speed Search after a
The alarm will appear only briefly. There is no need to take
momentary power loss or YES
action to prevent the alarm from occurring in such instances.
while attempting to perform a
fault restart.
LED Operator Display Minor Fault Name
Heatsink Overheat
oH
The temperature exceeded the maximum allowable value.
Minor Fault (H2-
Cause Possible Solutions
†† = 10)
• Check the surrounding temperature.
Surrounding temperature is • Improve the air circulation within the enclosure panel.
YES
too high • Install a fan or air conditioner to cool surrounding area.
• Remove anything near drive that may cause extra heat.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 211
5.5 Alarm Detection

• Replace the cooling fan. Refer to Cooling Fan Replacement

Internal cooling fan has on page 254.
YES
stopped. • After replacing the drive, reset the cooling fan maintenance
parameter to (o4-03 = “0”).
• Provide proper installation space around the drive as indicated
in the manual. Refer to Correct Installation Spacing on
page 42. YES
Airflow around the drive is • Allow for the specified space and ensure that there is sufficient
restricted. circulation around the control panel.
• Check for dust or foreign materials clogging cooling fan.
YES
• Clear debris caught in the fan that restricts air circulation.
LED Operator Display Minor Fault Name
Drive Overheat Warning
oH2 “Drive Overheat Warning” was input to a multi-function input terminal, S1 through
S7 (H1- = B).
Minor Fault (H2-
Cause Possible Solutions
†† = 10)
An external device triggered
• Search for the device that tripped the overheat warning.
and overheat warning in the YES
• Solving the problem will clear the warning.
drive.
LED Operator Display Minor Fault Name
Motor Overheat
oH3 The motor overheat signal entered to a multi-function analog input terminal
exceeded the alarm level (H3-02 or H13-10 = E).
Minor Fault (H2-
Cause Possible Solutions
†† = 10)
Motor
thermostat
Repair the PTC input wiring. YES
wiring is fault
(PTC input).
There is a fault on the
• Check the status of the machine.
machine side (e.g., the
• Remove the cause of the fault.
machine is locked up).
• Check the load size, accel/decel times, and cycle times.
• Decrease the load.
• Increase accel and decel times (C1-01 to C1-08).
• Adjust the preset V/f pattern (E1-04 through E1-10). This will
mainly involve reducing E1-08 and E1-10. Note: Do not lower
Motor has
E1-08 and E1-10 excessively, because this reduces load YES
overheated.
tolerance at low speeds.
• Check the motor-rated current.
• Enter motor-rated current on motor nameplate (E2-01).
• Ensure the motor cooling system is operating normally.
• Repair or replace the motor cooling system.
LED Operator Display Minor Fault Name

212 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 5.5 Alarm Detection

Overtorque 1
oL3 Drive output current (or torque in OLV) was greater than L6-02 for longer than the
time set in L6-03.
Minor Fault (H2-
Cause Possible Solutions
†† = 10)
Inappropriate parameter
Check parameters L6-02 and L6-03. YES
settings.
There is a fault on the
• Check the status of the machine.
machine side (e.g., the YES
• Remove the cause of the fault.
machine is locked up).
LED Operator Display Minor Fault Name
Overtorque 2
oL4 Drive output current (or torque in OLV) was greater than L6-05 for longer than the
time set in L6-06.

Troubleshooting
Minor Fault
Cause Possible Solutions Output
(H2-†† = 10)
Parameter settings are not
Check parameters L6-05 and L6-06. YES
appropriate.
There is a fault on the
machine side (e.g., the
• Check the status of the machine being used.
• Remove the cause of the fault.
YES 5
machine is locked up).
LED Operator Display Minor Fault Name
Overspeed (for Simple V/f with PG)
oS
Pulse input (RP) indicates that motor speed feedback exceeded F1-08 setting.
Minor Fault
Cause Possible Solutions Output
(H2-†† = 10)
• Adjust the gain by using the pulse train input parameters (H6-
02 through H6-05).
Overshoot or undershoot is
Adjust the speed feedback accuracy. YES
occurring.
• Increase the settings for C5-01 (Speed Control Proportional
Gain 1) and reduce C5-02 (Speed Control Integral Time 1).
PG pulse settings are Set the H6-02 (Pulse Train Input Scaling) = 100%, the number
YES
incorrect. of pulses during maximum motor revolutions.
Parameter settings are Check the setting for the overspeed detection level and the
YES
inappropriate. overspeed detection time (F1-08 and F1-09).
LED Operator Display Minor Fault Name
DC Bus Overvoltage
ov The DC bus voltage exceeded the trip point.
For 200 V class: approximately 410 V
For 400 V class: approximately 820 V (740 V when E1-01 < 400)

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 213
5.5 Alarm Detection

Minor Fault (H2-

Cause Possible Solutions
†† = 10)
• Install a DC reactor or an AC reactor.
Surge voltage present in the • Voltage surge can result from a thyristor convertor and a phase
YES
drive input power. advancing capacitor operating on the same drive input power
system.
• The motor has short-
circuited.
• Check the motor power cable, relay terminals and motor
• Ground current has
terminal box for short circuits. YES
over-charged the main circuit
• Correct grounding shorts and turn the power back on.
capacitors via the drive input
power.
• Review possible solutions for handling noise interference.
• Review section on handling noise interference and check
Noise interference causes the control circuit lines, main circuit lines and ground wiring. YES
drive to operate incorrectly. • If the magnetic contactor is identified as a source of noise,
install a surge protector to the MC coil.
Set number of fault restarts (L5-01) to a value other than 0. YES
LED Operator Display Minor Fault Name

PASS MEMOBUS/Modbus Comm. Test Mode Complete

Minor Fault
Cause Possible Solutions Output
(H2-†† = 10)
MEMOBUS/Modbus test has
This verifies that the test was successful. No output
finished normally.
LED Operator Display Minor Fault Name
PG Disconnect (for Simple V/f with PG)
PGo
Detected when no PG pulses received for a time longer than setting in F1-14.
Minor Fault
Cause Possible Solutions Output
(H2-†† = 10)
Pulse input (RP) is
Reconnect the pulse input (RP). YES
disconnected.
Pulse input (RP) wiring is
Correct the wiring. YES
wrong.
Motor brake is engaged. Ensure the brake releases properly YES
LED Operator Display Minor Fault Name
Motor Switch during Run
rUn
A command to switch motors was entered during run.
Minor Fault
Cause Possible Solutions Output
(H2-†† = 10)

214 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 5.5 Alarm Detection

A motor switch command was Change the operation pattern so that the motor switch command
YES
entered during run. is entered while the drive is stopped.
LED Operator Display Minor Fault Name
Fault Reset when Run Command Entered
rUnC
Fault reset was being executed when a run command was entered.
Minor Fault (H2-
Cause Possible Solutions
†† = 10)
Fault reset was being • Ensure that a run command cannot be entered from the external
executed when a run terminals or option card during fault reset. YES
command was entered. • Turn off the run command.
LED Operator Display Minor Fault Name
Undertorque Detection 1
UL3
Drive output current (or torque in OLV) less than L6-02 for longer than L6-03 time.

Troubleshooting
Minor Fault (H2-
Cause Possible Solutions
†† = 10)
Inappropriate parameter
Check parameters L6-02 and L6-03. YES
settings.
Load has dropped or
• Check for broken parts in the transmission system. YES
decreased significantly.
LED Operator Display Minor Fault Name 5
Undertorque Detection 2
UL4
Drive output current (or torque in OLV) less than L6-05 for longer than L6-06 time.
Minor Fault (H2-
Cause Possible Solutions
†† = 10)
Inappropriate parameter
Check parameters L6-05 and L6-06. YES
settings.
The load has dropped or
• Check for broken parts in the transmission system. YES
decreased significantly.
LED Operator Display Minor Fault Name
Undervoltage
• One of the following conditions was true when the drive was stopped and a run
command was entered:
Uv • DC bus voltage dropped below the level specified in L2-05.
• Contactor to suppress inrush current in the drive was open.
• Low voltage in the control drive input power. This alarm outputs only if L2-01 is
not 0 and DC bus voltage is under L2-05.
Minor Fault (H2-
Cause Possible Solutions
†† = 10)
Phase loss in the drive input Check for wiring errors in the main circuit drive input power.
YES
power. Correct the wiring.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 215
5.5 Alarm Detection

• Ensure the terminals have been properly tightened.

Loose wiring in the drive • Apply the tightening torque specified in this manual to fasten
YES
input power terminals. the terminals. Refer to Wire Gauges and Tightening Torque
on page 63
• Check the voltage.
There is a problem with the
• Lower the voltage of the drive input power so that it is within YES
drive input power voltage.
the limits listed in the specifications.
Drive internal circuitry is • Check the maintenance time for the capacitors (U4-05).
YES
worn. • Replace the drive if U4-05 exceeds 90%.
The drive input power
transformer is not large • Check for a tripped alarm when the magnetic contactor, line
enough and voltage drops breaker and leakage breaker are turned on. YES
when the power is switched • Check the capacity of the drive input power transformer.
on.
Air inside the drive is too hot. • Check the temperature inside the drive. YES
The CHARGE indicator light
• Replace the drive. YES
is broken or disconnected.

216 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 5.6 Operator Programming Errors

5.6 Operator Programming Errors

An Operator Programming Error (oPE) occurs when an inappropriate parameter is set or an
individual parameter setting is inappropriate. The drive will not operate until the parameter
is set correctly; however, no alarm or fault outputs will occur. If an oPE occurs, investigate
the cause and refer to Table 5.10 for the appropriate action. When oPE error is displayed,
press the ENTER button to display U1-34 (oPE fault constant). This monitor displays the
parameter causing the oPE error.

◆ oPE Codes, Causes, and Possible Solutions

Table 5.10 oPE Codes, Causes, and Possible Solutions

LED Operator Display Error Name

Troubleshooting
Drive Capacity Setting Fault
oPE01
Drive capacity and then value set to o2-04 do not match.
Cause Possible Solutions
The drive capacity setting
(o2-04) and the actual capacity of the drive are not the Correct the value set to o2-04.
same.
LED Operator Display Error Name
5
Parameter Range Setting Error
oPE02 Use U1-18 to find which parameters were set outside the
setting range.
Cause Possible Solutions
Parameters were set outside the possible setting range. Set parameters to the proper values.
Note: Other errors are given precedence over oPE02 when multiple errors occur at the same time.
LED Operator Display Error Name
Multi-Function Input Selection Error
oPE03 A contradictory setting is assigned to multi-function
contact inputs H1-01 through to H1-07.
Cause Possible Solutions
• Ensure all multi-function inputs are assigned to different
• The same function is assigned to two multi-function
functions.
inputs.
• Re-enter the multi-function settings to ensure this does
• Excludes “Not used” and “External Fault.”
not occur.
The Up command was set but the Down command was
not, or vice versa (settings 10 vs. 11). Correctly set functions that need to be enabled in
The Up 2 command was set but the Down 2 command combination with other functions.
was not, or vice versa (settings 75 vs. 76).

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 217
5.6 Operator Programming Errors

LED Operator Display Error Name

Run command for a 2-wire sequence was set, but forward/
reverse command for a 2-wire sequence was not. “Drive Correctly set functions that need to be enabled in
Enable” is set to a multi-function contact input (H1-01 = combination with other functions.
6A or H1-02 = 6A).
• Two of the following functions are set at the same time:
• Up / Down Command (10 vs. 11)
• Check if contradictory settings have been assigned to
• Up 2 / Down 2 Command (75 vs. 76)
the multi-function input terminals at the same time.
• Hold Accel/Decel Stop (A)
• Correct setting errors.
• Analog Frequency Reference Sample / Hold (1E)
• Offset Frequency 1, 2, 3 Calculations (44, 45, 46)
The Up/Down command (10, 11) is enabled at the same Disable control PID (b5-01 = “0”) or disable the Up/
time as PID control (b5-01). Down command.
• One of the following settings at the multi-function input
terminals:
• External Search Command 1 and External Search
Command 2 (61 vs. 62)
• Fast-Stop N.O. and Fast-Stop N.C. (15 vs. 17)
• KEB for Momentary Power Loss and High Slip Braking
(65, 66, 7A, 7B vs. 68)
Check for contradictory settings assigned to the
• Motor Switch Command and Accel/Decel Time 2 (16 vs.
multi-function input terminals at the same time.
1A)
Correct setting errors.
• KEB Command 1 and KEB Command 2 (65, 66 vs. 7A,
7B)
• FWD Run Command (or REV) and FWD/REV Run
Command (2-wire) (40, 41 vs. 42, 43)
• External DB Command and Drive Enable (60 vs. 6A))
• Motor Switch Command and UP2/DOWN2 Command
(16 vs. 75, 76)
• One of the following settings was entered while
H1-†† = 2 (Alternative Reference):
• b1-15 = 4 (Pulse Train Input) and H6-01 (Pulse Train
Input Function Selection) not = 0 (Frequency Reference)
• b1-15 or b1-16 set to 3 but no option card connected
• Although b1-15 = 1 (Analog Input) and H3-02 or H3-10 Correct the settings for the multi-function input terminal
are set to 0 (Frequency Bias). parameters.
H2-†† = 38 (Drive Enabled) but H1-†† is not set to
6A (Drive Enable).
H1-†† = 7E (Direction Detection) although H6-01 is not
set to 3 (Simple V/f with PG).
LED Operator Display Error Name

oPE04 Initialization required.

218 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 5.6 Operator Programming Errors

LED Operator Display Error Name

Cause Possible Solutions
To load the parameter settings to the drive that are stored
The drive, control board, or terminal board has been
in the terminal board, set A1-03 to 5550.
replaced and the parameter settings between the control
Initialize parameters after drive replacement by setting
board and the terminal board no longer match.
A1-03 to 1110 or 2220.
LED Operator Display Error Name
Run Command Selection Error
oPE05 The Run command selection parameter b1-02 is set to 3
but no option board is installed.
Cause Possible Solutions
Frequency reference is assigned to an option card
(b1-01 = 3) that is not connected to the drive.
Reconnect the option card to the drive.

Troubleshooting
The Run command is assigned to an option card
(b1-02 = 3) that is not connected to the drive.
Frequency reference is assigned to the pulse train input
(b1-01 = 4), but terminal RP is not set for pulse train input Set H6-01 to “0”.
(H6-01 is greater than 0).
LED Operator Display Error Name
Multi-Function Analog Input Selection Error
A contradictory setting is assigned to multi-function
5
oPE07
analog inputs H3-02 through to H3-10 and PID functions
conflict.
Cause Possible Solutions
Change the settings to H3-02 and H3-10 so that functions
no longer conflict. Note: Both 0 (primary analog
H3-02 and H3-10 are set to the same value.
frequency reference) and F (Not Used) can be set to
H3-02 and H3-10 at the same time.
The following simultaneous contradictory settings:
H3-02 or H3-10 = B (PID Feedback)
H6-01 (Pulse Train Input) = 1 (PID Feedback)
The following simultaneous contradictory settings:H3-02
or H3-10 = C (PID Target Value)
H6-01 = 2 (pulse train input sets the PID target value)
Disable one of the PID selections.
The following simultaneous contradictory settings:H3-02
or H3-10 = C (PID Target Value)
b5-18 = 1 (enables b5-19 as the target PID value)
The following simultaneous contradictory settings:H6-01
or H3-10 = C (PID Target Value)
b5-18 = 1 (enables b5-19 as the target PID value)

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 219
5.6 Operator Programming Errors

LED Operator Display Error Name

LED Operator Display Error Name
Parameter Selection Error
oPE08 A function has been set that cannot be used in the motor
control method selected.
Cause Possible Solutions
Attempted to use a function in the V/f motor control Check the motor control method and the functions
method that is only possible in Open Loop Vector Control. available.
Simple V/f with PG was enabled while not in V/f Control To use Simple V/f with PG, ensure the motor control
(H6-01 = 3). method has been set to V/f Control (A1-02 = “0”).
Correct parameter settings so that n2-02 is less than
In Open Loop Vector Control, n2-02 is greater than n2-03
n2-03.
Correct parameter settings so that C4-02 is less than
In Open Loop Vector Control, C4-02 is greater than C4-06
C4-06.
• Set the correct motor code in accordance with the motor
In PM Open Loop Vector Control, parameters E5-02 to being used (E5-01).
E5-07 are set to 0. • When using a special-purpose motor, set E5-†† in
accordance with the Test Report provided.
The following conditions are true in PM Open Loop
Set E5-09 or E5-24 to the correct value, and set the other
Vector Control:
to “0”.
E5-03 does not equal 0
Set the motor-rated current for PM to “0” (E5-03).
E5-09 and E5-24 are both equal to 0, or neither equals 0
Note: Use U1-18 to find which parameters are set outside the specified setting range.
Other errors are given precedence over OPE08 when multiple errors occur at the same time.
LED Operator Display Error Name
PID Control Selection Fault
oPE09 PID control function selection is incorrect.
Requires that PID control is enabled (b5-01 = 1 to 4).
Cause Possible Solutions
The following simultaneous contradictory settings:
• Set b5-15 to another value besides 0.
b5-15 not 0.0 (PID Sleep Function Operation Level)
• Set the stopping method to coast to stop or ramp to stop
The stopping method is set to either DC injection braking
(b1-03 = “0” or “1”).
or coast to stop with a timer (b1-03 = 2 or 3).
LED Operator Display Error Name
V/f Data Setting Error
The following setting errors have occurred where:
E1-04 is greater than or equal to E1-06 is greater than or
oPE10 equal to E1-07 is greater than or equal to E1-09.
Or the following setting errors have occurred:
E3-04 is greater than or equal to E3-06 is greater than or
equal to E3-07 is greater than or equal to E3-09.

220 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 5.6 Operator Programming Errors

LED Operator Display Error Name

Cause Possible Solutions
Correct the settings for E1-04, -06, -07 and -09 (or E-04,
—
-06, -07, -09 for motor 2).
LED Operator Display Error Name
Carrier Frequency Setting Error
oPE11
Correct the setting for the carrier frequency.
Cause Possible Solutions
The following simultaneous contradictory settings:
C6-05 is greater than 6 and C6-04 is greater than C6-03
(carrier frequency lower limit is greater than the upper
limit). If C6-05 is less than or equal to 6, the drive Correct the parameter settings.
operates at C6-03.

Troubleshooting
Upper and lower limits between C6-02 and C6-05
contradict each other.
Pulse Monitor Selection Error
oPE13 Incorrect setting of monitor selection for Pulse Train
(H6-06) .
Cause Possible Solutions
Scaling for the Pulse Train
monitor is set to 0 (H6-07 = Change scaling for the Pulse Train monitor or set H6-06
5
0) while H6-06 is not set to to 101, 102, 105, or 116..
101, 102, 105, or 116.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 221
5.7 Auto-Tuning Fault Detection

5.7 Auto-Tuning Fault Detection

Auto-Tuning faults are shown below. When the following faults are detected, the fault is
displayed on the Digital Operator and the motor coasts to a stop. No fault or alarm outputs
will occur

◆ Auto-Tuning Codes, Causes, and Possible Solutions

Table 5.11 Auto-Tuning Codes, Causes, and Possible Solutions

LED Operator Display Error Name

Er-01 Motor Data Error

Cause Possible Solutions

• Check that the motor data entered to the T1 parameters match the information
Motor data or data entered
written on the motor nameplate input before Auto-Tuning.
during Auto-Tuning incorrect.
• Start Auto-Tuning over again and enter the correct information.
Motor output and motor-rated
• Check the drive and motor capacities.
current settings (T1-02 and
• Correct the settings of parameters T1-02 and T1-04.
T1-04) do not match.
Motor output and no-load
current settings (T1-04 and
E2-03) do not match.
This data is required only when • Check the motor-rated current and no-load current.
Auto-Tuning for Open Loop • Correct the settings of parameters T1-04 and E2-03.
Vector Control or when
performing Stationary
Auto-Tuning.
Base frequency and base motor
rotations (T1-05 and T1-07) do Set T1-05 and T1-07 to the correct value.
not match.
LED Operator Display Error Name

Er-02 Minor Fault

Cause Possible Solutions

• Motor data entered to the T1 parameters does not match the information written
Motor data entered during
on the motor nameplate. Enter the correct data.
Auto-Tuning was incorrect.
• Start Auto-Tuning over again and enter the correct information.

The wiring is faulty. • Check the wiring and correct defective connections.
• Check around the machine.
• Check the load.
Load is too heavy.
• Use the information on page 237 to find out what caused the problem.
LED Operator Display Error Name

Er-03 STOP Button Input

222 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 5.7 Auto-Tuning Fault Detection

Cause Possible Solutions

Auto-Tuning canceled by
Auto-Tuning did not complete properly and will have to be performed again.
pressing STOP button.
LED Operator Display Error Name

Er-04 Line-to-Line Resistance Error

Cause Possible Solutions

• Motor data entered to the T1 parameters does not match the information written
Motor data entered during
on the motor nameplate. Enter the correct data.
Auto-Tuning was incorrect.
• Start Auto-Tuning over again and enter the correct information.
Auto-Tuning did not complete
within designated time frame. • Check and correct faulty motor wiring.
Drive-caculated values outside • Disconnect the motor from machine and perform Rotational Auto-Tuning.
parameter setting range.

Troubleshooting
LED Operator Display Error Name

Er-05 No-Load Current Error

Cause Possible Solutions

• Motor data entered to the T1 parameters does not match the information written
Motor data entered during
on the motor nameplate. Enter the correct data.
Auto-Tuning was incorrect.
• Restart Auto-Tuning and enter the correct information. 5
Auto-Tuning did not complete
within designated time frame. • Check and correct faulty motor wiring.
Drive-caculated values outside • Disconnect the motor from machine and perform Rotational Auto-Tuning.
parameter setting range.
LED Operator Display Error Name

Er-08 Rated Slip Error

Cause Possible Solutions

• Motor data entered to the T1 parameters does not match the information written
Motor data entered during
on the motor nameplate. Enter the correct data.
Auto-Tuning was incorrect.
• Restart Auto-Tuning and enter the correct information.
Auto-Tuning did not complete
within designated time frame.
• Check and correct faulty motor wiring.
Values calculated by the drive • Disconnect the motor from machine and perform Auto-Tuning.
are outside the allowable
parameter setting ranges.
LED Operator Display Error Name

Er-09 Acceleration Error (detected only during Rotational Auto-Tuning)

Cause Possible Solutions

The motor did not accelerate for • Increase the acceleration time (C1-01).
the specified acceleration time. • Check if it is possible to disconnect the machine from the motor.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 223
5.7 Auto-Tuning Fault Detection

Torque limit when motoring is • Check the settings of parameters L7-01 and L7-02).
too low (L7-01 and L7-02). • Increase the setting.
LED Operator Display Error Name

Er-11 Motor Speed Fault (detected only when Auto-Tuning is enabled)

Cause Possible Solutions

Torque reference is too high. • Increase the acceleration time (C1-01).
(Enabled in OLV only.) • Disconnect the machine from the motor, if possible.
LED Operator Display Error Name
Er-12 Current Detection Error
Cause Possible Solutions
One of the motor phases is
Check motor wiring and correct problems.
missing (U/T1, V/T2, W/T3).
Current exceeded the current
rating of the drive. • Check the motor wiring for a short between motor lines.
• If a magnetic contactor is used between motors, ensure it is on.
The current is too low. • Replace the drive.

Attempted Auto-Tuning without

Connect the motor and perform Auto-Tuning.
motor connected to the drive.
Current detection signal error. Replace the drive.
LED Operator Display Error Name
Excessive V/f Setting. Detected only during Rotational Auto-Tuning, and
End1
displayed after Auto-Tuning is complete.
Cause Possible Solutions
The torque reference exceeded
20% during Auto-Tuning. • Before Auto-Tuning the drive, verify the information written on the motor
nameplate and enter that data to T1-03 through T1-05.
The results from Auto-Tuning • Enter proper information to parameters T1-03 to T1-05 and repeat Auto-Tuning.
the no-load current exceeded • If possible, disconnect the motor from the load and perform Auto-Tuning.
80%.
LED Operator Display Error Name
Motor Iron-Core Saturation Coefficient. Detected only during Rotational
End2
Auto-Tuning and displayed after Auto-Tuning is complete.
Cause Possible Solutions
• Motor data entered to the T1 parameters does not match the information written
Motor data entered during
on the motor nameplate.
Auto-Tuning was incorrect.
• Restart Auto-Tuning and enter the correct information.
Auto-Tuning calculated values
outside the parameter setting
• Check and correct faulty motor wiring.
range, assigning the iron-core
• Disconnect the motor from machine and perform Rotational Auto-Tuning.
saturation coefficient (E2-07, -
08) a temporary value.

224 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 5.7 Auto-Tuning Fault Detection

LED Operator Display Error Name

End3 Rated Current Setting Alarm (displayed after Auto-Tuning is complete)

Cause Possible Solutions

• The motor line-to-line
resistance and the motor-rated
current are not consistent with
• Check the setting of parameter T1-04.
one another.
• Check the motor data and repeat Auto-Tuning.
• The correct current rating
printed on the nameplate was
not entered into T1-04.

Troubleshooting
5

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 225
5.8 Diagnosing and Resetting Faults

5.8 Diagnosing and Resetting Faults

When a fault occurs and the drive stops, follow the instructions below to remove whatever
conditions triggered the fault, then restart the drive.

◆ Fault Occurs Simultaneously with Power Loss

WARNING! Electrical Shock Hazard. Ensure there are no short circuits between the main circuit terminals
(R/L1, S/L2, and T/L3) or between the ground and main circuit terminals before restarting the drive. Failure
to comply may result in serious injury or death and will cause damage to equipment.

1. Turn on the drive input power.

2. Use monitor parameters U2-†† to display data on the operating status of the drive
just before the fault occurred.
3. Remove the cause of the fault and reset.
Note: To find out what faults were triggered, check U2-02 (Fault History). Information on drive status
when the fault occurred such as the frequency, current and voltage, can be found in U2-03
through U2-17. Refer to Viewing Fault Trace Data after Fault on page 227 for information on
how to view fault trace data.
Note: When the fault continues to be displayed after cycling power, remove the cause of the fault and
reset.

◆ If the drive still has power after a fault occurs

1. Look at the LED operator for information on the fault that occurred.
2. Fault Displays, Causes, and Possible Solutions on page 187
3. Reset the fault. Refer to Fault Reset Methods on page 227.

226 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 5.8 Diagnosing and Resetting Faults

◆ Viewing Fault Trace Data after Fault

Step Display/Result

1. Turn on the drive input power. The first screen displays. ⇒

2. Press until the monitor screen is displayed. ⇒

3. Press to display the parameter setting screen. ⇒

Troubleshooting
4. Press and > until U2-02 (Fault History) is displayed. ⇒

5. Press to view most recent fault (here, oC). ⇒

6. Press to view drive status information when fault occurred.

7. Parameters U2-03 through U2-17 help determine cause of fault. ⇒ 㨪 5

◆ Fault Reset Methods

After the Fault Occurs Procedure

Fix the cause of the fault,

Press the RESET button on the
restart the drive, and reset the
digital operator
fault
STOP

Drive
Close then open the fault signal
Resetting via Fault Reset Fault Reset Switch
digital input via terminal S4. S4 is set S4 Fault Reset Digital Input
Digital Input S4
fault reset as default (H1-04 = 12) SC Digital Input Common

 ON
If the above methods do not reset the fault, turn off the drive main
power supply. Reapply power after LED operator display is out.
 OFF

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 227
5.9 Troubleshooting without Fault Display

5.9 Troubleshooting without Fault Display

This section is for troubleshooting problems that do not trip an alarm or fault.

◆ Cannot Change Parameter Settings

Cause Possible Solutions
The drive is running the motor (i.e., the • Stop the drive and switch over to the Programming Mode.
Run command is present). • Most parameters cannot be edited during run.
The Access Level is set to restrict access
• Set the Access Level to allow parameters to be edited (A1-02 = 2).
to parameter settings.
The operator is not in the Parameter • See what mode the LED parameter is current set for.
Setup Mode (the LED screen will display • Parameters cannot be edited when in the Setup Mode (“STUP”). Switch
“PAr”). modes so that “PAr” appears on the screen.
A multi-function contact input terminal is
• When the terminal is open, parameters cannot be edited.
set to allow or restrict parameter editing
• Turn on the multi-function contact input set to 1B.
(H1-01 through H1-10 = 1B).
• If the password entered to A1-04 does not match the password saved to
A1-05, then drive settings cannot be changed.
• Reset the password.
• If you cannot remember the password:
The wrong password was entered.
• Display parameter A1-04. Press the STOP button while pressing

at the same time. Parameter A1-05 will appear.

• Set a new password to parameter A1-05.
• Check the drive input power voltage by looking at the DC bus voltage
Undervoltage was detected. • (U1-07).
• Check all main circuit wiring.

◆ Motor Does Not Rotate Properly after Pressing RUN Button

or After Entering External Run Command
■ Motor Does Not Rotate

Cause Possible Solutions

• Check if the DRV light on the LED operator is lit.
The drive is not in the Drive Mode. • Enter the Drive Mode to begin operating the motor. Refer to The Drive
and Programming Modes on page 97.

228 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 5.9 Troubleshooting without Fault Display

Cause Possible Solutions

• Stop the drive and check if the correct frequency reference source is
selected. If the operator keypad shall be the source, the LO/RE button
LED must be on, if the source is REMOTE, it must be off.
The LO/RE button was pushed.
• Take the following steps to solve the problem:
• Push the LO/RE button.
• If o2-01 is set to 0, then the LO/RE button will be disabled.
• When Auto-Tuning has completed, the drive is switched back to the
Programming Mode. The Run command will not be accepted unless
Auto-Tuning has just completed. the drive is in the Drive Mode.
• Use the LED operator to enter the Drive Mode. Refer to The Drive
and Programming Modes on page 97.
A Fast-Stop was executed and has not
Reset the the Fast-Stop command.
yet been reset.
Check parameter b1-02 (Run Command Selection).

Troubleshooting
Set b1-02 so that it corresponds with the correct run command source.
Settings are incorrect for the source that 0: LED/LCD operator
provides the run command. 1: Control circuit terminal (default setting)
2: MEMOBUS/Modbus communications
3: Option card
• Check for a short-circuit between terminals H1 and HC.
One of the Safety Inputs is open. • See if one of the Safety Inputs is open.
• Correct any faulty wiring. 5
• Check the wiring for the control terminal.
There is faulty wiring in the control
• Correct wiring mistakes.
circuit terminals.
• Check the input terminal status monitor (U1-10).
Check parameter b1-01 (Frequency Reference Selection 1).
Set b1-01 to the correct source of the frequency reference.
The drive has been set to accept the 0: LED operator
frequency reference from the incorrect 1: Control circuit terminal (default setting)
source. 2: MEMOBUS/Modbus communications
3: Option card
4: Pulse train input (RP)
The terminal set to accept the main speed
Check DIP switch S1. Next assign the correct input level to terminal A2
reference is set to the incorrect voltage
(H3-09). Refer to Terminal A2 Switch on page 79.
and/or current.
Selection for the sink/source mode is Check DIP switch S3. Refer to Sinking/Sourcing Mode Switch on
incorrect. page 77.
• Check the frequency reference monitor (U1-01).
Frequency reference is too low. • Increase the frequency by changing the maximum output frequency
(E1-09).

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 229
5.9 Troubleshooting without Fault Display

Cause Possible Solutions

• Check the multi-function analog input settings.
• Check if analog input A1 or A2 is set for frequency reference gain
Multi-function analog input is set up to
(H3-02/10 = 1). If so, check if the correct signal is applied to the
accept gain for the frequency reference,
terminal. The gain and the frequency reference will be 0 if no signal is
but no voltage (current) has been
applied to the gain input.
provided.
• Check if H3-02 and H3-10 have been set to the proper values.
• Check if the analog input value has been set properly.
The STOP button was pressed when the • When the STOP button is pressed, the drive will decelerate to stop.
drive was started from a REMOTE • Switch off the run command and then re-enter a run command.
source. • The STOP button is disabled when o2-02 is set to 0.
• Ensure the selected V/f pattern corresponds with the characteristics of
the motor being used.
• Set the correct V/f pattern to E1-03.
• When E1-03 = F, increase both the minimum and mid output
frequency voltages (E1-08, E1-10).
Motor is not producing enough torque in
the V/f motor control method. Increase the frequency reference so that it is higher than the minimum
frequency reference (E1-09).
Perform Line-to-Line Resistance Auto-Tuning when using particularly
long motor cables.
Increase the torque compensation gain (C4-01).
• Execute Rotational Auto-Tuning.
• If the motor cables are replaced with longer cables after Rotational
Auto-Tuning was performed, Auto-Tuning may need to be repeated
due to voltage drop across the line.
Motor is not producing enough torque in
• Check if the torque limit parameters have been set too low (L7-01
Open Loop Vector Control.
through L7-04).
• Reset the torque limit back to its default setting (200%).
Increase both the minimum and mid output frequency voltages
(E1-08 and E-10).
• The drive is set for a 3-wire sequence when one of parameters H1-03
through H1-07 is set to 0.
The drive is set for both 2-wire and • If the drive is supposed to be set up for a 2-wire sequence, then ensure
3-wire sequence at the same time. parameters H1-03 through H1-07 are not set to 0.
• If the drive is supposed to be set up for a 3-wire sequence, then
H1- must be set to 0. Refer to Table 5.2 for additional information.

■ Motor Rotates in the Opposite Direction from the Run Command

Cause Possible Solutions

• Check the motor wiring.
Phase wiring between the drive and motor • Switch two motor cables (U, V, and W) to reverse motor direction.
is incorrect. • Connect drive output terminals U/T1, V/T2 and W/T3 in the right order
to the corresponding motor terminals U, V, and W.

230 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 5.9 Troubleshooting without Fault Display

Cause Possible Solutions

• Typically, forward is designated as being counterclockwise when
looking from the motor shaft (refer to the figure below).

1
The forward direction for the motor is
set-up incorrectly.

2
• 1. Forward Rotating Motor (looking down the motor shaft)
2. Motor Shaft
The motor is running at almost 0 Hz and
• Disable bi-directional search (b3-14 = “0”) so that Speed Search is
the Speed Search estimated the speed to
performed only in the specified direction.
be in the opposite direction.

Troubleshooting
Note: Check the motor specifications for the forward and reverse directions. The motor specifications
will vary depending on the manufacturer of the motor.

■ Motor Rotates in One Direction Only

Cause Possible Solutions

The drive prohibits reverse rotation.

• Check parameter b1-04. 5
• Set the drive to allow the motor to rotate in reverse (b1-04 = “0”).
A Reverse run signal has not been
• Make sure that one of the input terminals S3 to S7 used for the 3-wire
entered, although 3-wire sequence is
sequence has been set for reverse.
selected.

■ Motor is Too Hot

Cause Possible Solutions

• If the load is too heavy for the motor, the motor will overheat as it
exceeds its rated torque value for an extended period of time.
• Keep in mind that the motor also has a short-term overload rating in
addition to the possible solutions provided below:
The load is too heavy. • Reduce the load.
• Increase the acceleration and deceleration times.
• Check the values set for the motor protection (L1-01, L1-02) as well as
the motor rated current (E2-01).
• Increase motor capacity.
• Check the ambient temperature.
The air around the motor is too hot.
• Cool the area until it is within the specified temperature range.
The drive is operating in a vector control • Perform Auto-Tuning.
mode but Auto-Tuning has not yet been • Calculate the motor value and reset the motor parameters.
performed. • Change the motor control method to V/f Control (A1-02 = “0”).

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 231
5.9 Troubleshooting without Fault Display

Cause Possible Solutions

When the motor is connected to terminals U/T1, V/T2, and W/T3,
voltage surges occur between the motor coils and drive switching.
Normally, surges can reach up to three times the drive input power supply
Insufficient voltage tolerance between voltage (600 V for 200 V class, and 1200 V for 400 V class).
motor phases. Use a motor with voltage tolerance higher than the max voltage surge.
Use a motor designed to work specifically with a drive when using a 400
V class unit.
Install an AC reactor on the output side of the drive.
The motor fan has stopped or is clogged. Check the motor fan.

■ Drive Does Not Allow Selection of Rotational Auto-Tuning

Cause Possible Solutions

• Check if the drive is set to V/f Control by accident (A1-02 = 0).
The drive is in the incorrect motor control
• Change the motor control method to Open Loop Vector Control
method for Rotational Auto-Tuning.
(A1-02 = “2”).

■ Motor Hunting Occurs at Low Speeds

Cause Possible Solutions

• Excess load inertia can cause motor hunting in Open Loop Vector
Control due to slow motor response.
Excessive load inertia in Open Loop • Increase the speed feedback detection control time constant (n2-02)
Vector Control. from its default value of 50 ms to an appropriate level between 200 and
1000 ms. Adjust this setting in combination with n2-03 (Feedback
Detection Control Time Constant 2).

■ Overvoltage Occurs When Running at a Constant Speed

Cause Possible Solutions

• Loads with a lot of inertia (fans, etc.) can trigger an overvoltage fault
when operating in Open Loop Vector Control.
Excessive load inertia in Open Loop
• Switch to the V/f motor control method.
Vector Control.
• Adjust the values set for the speed feedback detection control time
constant (n2-02, n2-03).

232 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 5.9 Troubleshooting without Fault Display

■ Motor Stalls During Acceleration or With Large Loads

Cause Possible Solutions

• Take the following steps to resolve the problem:
• Reduce the load.
• Increase the acceleration time.
Load is too heavy. • Increase motor capacity.
• Although the drive has a Stall Prevention function and a Torque
Compensation Limit function, accelerating too quickly or trying to drive
an excessively large load can exceed the capabilities of the motor.

■ Motor Will Not Accelerate or the Acceleration Time is Too Long

Cause Possible Solutions

Troubleshooting
• Check the maximum output frequency (E1-04).
• Increase E1-04 if it is set too low.
Check U1-01 for proper frequency reference.
Frequency reference is too low.
Check if a frequency reference signal switch has been set to one of the
multi-function input terminals.
Check for low gain level set to terminals A1 or A2 (H3-03, H3-11).
• Reduce the load so that the output current remains within the
motor-rated current. 5
Load is too heavy. • In extruder and mixer applications, the load will sometimes increase as
the temperature drops.
Check if the mechanical brake is fully releasing as it should.
• Check the torque limit setting. It may be too low. (L7-01 through L7-
The torque limit function is operating in
04).
Open Loop Vector Control.
• Reset the torque limit to its default value (200%).
Check if the acceleration time parameters have been set too long (C1-01,
Acceleration time has been set too long.
-03, -05, -07).
Motor characteristics and drive parameter • Select the correct V/f pattern so that it matches the characteristics of the
settings are incompatible with one motor being used.
another in V/f Control. • Check E1-03 (V/f Pattern Selection).
The right combination of motor
characteristics have not been set in Open Execute Rotational Auto-Tuning.
Loop Vector Control.
• Check the multi-function analog input settings.
• Check if multi-function analog input terminal A1 or A2 is set for
frequency gain (H3-02 or H3-10 = “1”). If so, the frequency reference
Incorrect frequency reference setting.
will be 0 if there is no voltage (current) input provided.
• Ensure H3-02 and H3-10 are set to the proper values.
• Ensure the analog input value is set to the right value (U1-13, U1-14).
• Check the Stall Prevention level during acceleration (L3-02).
The Stall Prevention level during
• If L3-02 is set too low, acceleration will take a fair amount of time.
acceleration and deceleration set too low.
• Increase L3-02.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 233
5.9 Troubleshooting without Fault Display

Cause Possible Solutions

• Check the Stall Prevention level during run (L3-06).
The Stall Prevention level during run has
• If L3-06 is set too low, speed will drop as the drive outputs torque.
been set too low.
• Increase the setting value.
Although the drive is operating in Open • Perform Auto-Tuning.
Loop Vector motor control method, • Calculate motor data and reset motor parameters.
Auto-Tuning has not been performed. • Switch to the V/f motor control method (A1-02 = “0”).
• The motor cable may be long enough (over 50 m) to require Auto-
Drive reached the limitations of the V/f Tuning for line-to-line resistance. Also be aware that V/f Control is
motor control method. comparatively limited when it comes to producing torque at low speeds.
• Consider switching to Open Loop Vector Control.

■ Drive Frequency Reference Differs from the Controller Frequency

Reference Command

Cause Possible Solutions

• Check the frequency reference terminal input gain level assigned to
The analog input frequency gain and bias terminals A1 and A2, as well as the frequency reference input bias to
are set to incorrect values. terminal A1 and A2 (parameters H3-03, H3-04, and H3-12).
• Set these parameters to the appropriate values.
• If multi-function analog input terminals A1 and A2 are set for frequency
reference (H3-02 = 0 and H3-10 = 0), the addition of both signals builds
A frequency bias signal is being entered
the frequency reference.
via analog input terminals A1 or A2.
• Ensure that H3-02 and H3-10 are set appropriately.
• Check the input level set for terminals A1 and A2 (U1-13, U1-14).

■ Poor Speed Control Accuracy

Cause Possible Solutions

Drive reached the slip compensation • Check the slip compensation limit (C3-03).
limit. • Increase the value set to C3-03.
• The input voltage for the drive determines the maximum output voltage.
A drive with an input of 200 Vac can only output a maximum of 200 Vac.
Open Loop Vector Control sometimes calculates an output voltage
Motor-rated voltage is set too high in
reference value that exceeds the maximum drive output voltage level,
Open Loop Vector Control.
resulting in a loss of speed control accuracy.
• Use a motor with a lower voltage rating (a vector control motor).
• Increase the input power voltage.
Auto-Tuning did not complete properly
• Perform Auto-Tuning again.
for Open Loop Vector Control.

234 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 5.9 Troubleshooting without Fault Display

■ Deceleration Takes Too Long With Dynamic Braking Enabled

Cause Possible Solutions

• Check the Stall Prevention Level during deceleration (L3-04).
L3-04 is set incorrectly. • If a braking resistor option has been installed, disable Stall Prevention
during deceleration (L3-04 = “0”).
The deceleration time is set too long. Set deceleration to more appropriate time (C1-02, C1-04, C1-06, C1-08).
• Assuming parameter settings are normal and that no overvoltage occurs
when there is insufficient torque, it is likely that the demand on the motor
Insufficient motor torque.
has exceeded the motor capacity.
• Use a larger motor.
• Check the settings for the torque limit (L7-01 through L7-04).
• If the torque limit is enabled, deceleration might take longer than
expected because the drive cannot output more torque than the limit

Troubleshooting
setting. Ensure the torque limit is set to a large enough value.
• Increase the torque limit setting.
Reaching the torque limit.
• If multi-function analog input terminal A1 or A2 is set to torque limit
(H3-02 or H3-10 equals 10, 11, 12, or 15), ensure that the analog input
levels are set to the correct levels.
• Ensure H3-02 and H3-10 are set to the right levels.
• Ensure the analog input is set to the correct value.
Load exceeded the internal torque limit
determined by the drive rated current.
Switch to a larger capacity drive. 5
■ Motor Hunting Occurs When Operating With a Light Load

Cause Possible Solutions

Carrier frequency is too high. Lower the carrier frequency setting C6-02.
• Select the proper V/f pattern (E1-03).
Large V/f setting value at low speeds
• Use parameters E1-04 through E1-10 to set the V/f pattern in relation to
triggers overexcitation.
the load characteristics.
The maximum output frequency and the
Set the proper values for the maximum output frequency and base
base frequency reference are not set
frequency (E1-04, E1-06).
properly in relationship to each other.
• Enable Hunting Prevention by setting n1-01 = “1”.
Hunting Prevention is disabled (V/f
• (OLV only) Increase the speed feedback detection control gain and time
control only).
constant (n2-01, n2-02).

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 235
5.9 Troubleshooting without Fault Display

■ Load Falls When Brake is Applied (Hoist-Type Applications)

Cause Possible Solutions

• Use frequency reference detection for closing and releasing the brake.
• At start: Release the brake after creating enough torque.
• At stop: Close the brake when the motor still produces torque.
• Make the following setting changes to hold the brake:
• Set the frequency detection inactive during baseblock (L4-07 = 0).
• Multi-function contact output terminal will switch on when the output
The timing for the brake to close and
frequency is greater than the frequency detection level set in L4-01. Set
release is not set properly.
L4-01 between 1.0 and 3.0 Hz.
• Slipping may occur when stopping because hysteresis is used in
Frequency Reference 2 (where the frequency agree setting in L4-02 is
2.0 Hz). To prevent this, change the setting to 0.1 Hz.
• Do not use the multi-function contact output setting “During Run”
(H2-01 = 0) for the brake signal.
Insufficient DC Injection Braking. Increase the amount of DC Injection Braking (b2-02).

■ Noise From Drive or Output Lines When the Drive is Powered On

Cause Possible Solutions

• Lower the carrier frequency (C6-02).
• Install a noise filter on the input side of drive input power.
Relay switching in the drive generates • Install a noise filter on the output side of the drive.
excessive noise. • Place the wiring inside a metal conduit to shield it from switching noise.
• Ground the drive and motor properly
• Separate the main circuit wiring and the control lines.

■ Ground Fault Circuit Interrupter (GFCI) Trips During Run

Cause Possible Solutions

• Increase the GFCE sensitivity or use GFCI with a higher threshold.
• Lower the carrier frequency (C6-02).
Excessive leakage current trips MCCB.
• Reduce the length of the cable used between the drive and the motor.
• Install a noise filter or reactor on the output side of the drive.

■ Connected Machinery Vibrates When Motor Rotates

Excessive Motor Oscillation and Erratic Rotation

Cause Possible Solutions

Poor balance between motor phases. Check drive input power voltage to ensure that it provides stable power.

236 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 5.9 Troubleshooting without Fault Display

Unexpected Noise from Connected Machinery

Cause Possible Solutions

The carrier frequency is at the resonant
Adjust the carrier frequency using parameters C6-02 through C6-05.
frequency of the connected machinery.
The drive output frequency is the same • Adjust the parameters used for the Jump Frequency function (d3-01
as the resonant frequency of the through d3-04) to skip the problem-causing bandwidth.
connected machinery. • Place the motor on a rubber pad to reduce vibration.

Note: The drive may have trouble assessing the status of the load due to white noise generated when
using Swing PWM (C6-02 = 7 to A, or 7 if set for Normal Duty).

■ Oscillation or Hunting

Cause Possible Solutions

Troubleshooting
• Adjust the following parameters in the order listed to get better gain.
• An increase in gain should be followed with an increase in the primary
delay time constant.
Insufficient tuning in Open Loop Vector C4-02 (Torque Compensation Primary Delay Time)
Control. n2-01 (Speed Feedback Detection Control [AFR] Time Constant 1)
C3-02 (Slip Compensation Primary Delay Time)
• The response for torque compensation and slip compensation will drop
as the time constant is increased. 5
• Perform Auto-Tuning.
Auto-Tuning has not yet been performed
• Set motor parameters after calculating the proper values.
(required for Open Loop Vector Control).
• Change the motor control method to V/f Control (A1-02 = “0”).
• Adjust the following parameters in the order listed to get better gain.
• An increase in gain should be followed with an increase in the primary
delay time constant.
Insufficient tuning in Open Loop Vector C4-02 (Torque Compensation Primary Delay Time)
Control. n2-02 (AFR Time Constant 1)
n1-02 (Hunting Prevention Gain Setting)
• The response for torque compensation and slip compensation will drop
as the time constant is increased.
Gain is too low when using PID control. Check the period of oscillation and adjust P, I, and D settings accordingly.
• Ensure that noise is not affecting the signal lines.
The frequency reference is assigned to an • Separate main circuit wiring and control circuit wiring.
external source. • Use twisted-pair cables or shielded wiring for the control circuit.
• Increase the analog input time filter constant (H3-13).
The cable between the drive and motor is • Perform Auto-Tuning.
too long. • Reduce the length of the cable.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 237
5.9 Troubleshooting without Fault Display

■ PID output fault

Cause Possible Solutions

• Check the multi-function analog input terminal settings.
• Set multi-function analog input terminal A1 or A2 for PID feedback
(H3-02 or H3-10 = “B”).
• A signal input to the terminal selection for PID feedback is necessary.
No PID feedback input.
• Check the connection of the feedback signal.
• Check the various PID-related parameter settings.
• No PID feedback input to the terminal causes the value detected to be 0,
causing a PID fault and the drive to operate at max frequency.
• PID control keeps the difference between target and detection values at
The level of detection and the target 0. Set the input level for the values relative to one another.
value do not correspond with each other. • Use analog input gains H3-03/11 to adjust PID target and feedback
signal scaling.
Reverse drive output frequency and
speed detection. When output frequency Set PID output for reverse characteristics (b5-09 = “1”).
rises, the sensor detects a speed decrease.

■ Insufficient Motor Torque

Cause Possible Solutions

Auto-Tuning has not yet been performed
Perform Auto-Tuning.
(required for OLV Control).
The control mode was changed after
Perform Auto-Tuning again.
performing Auto-Tuning.
Only Line-to-Line Resistance
Perform Rotational Auto-Tuning.
Auto-Tuning was performed.

■ Motor Rotates After the Drive Output is Shut Off

Cause Possible Solutions

• Adjust the DC Injection braking settings.
Low DC Injection Braking and the drive
• Increase the value of b2-02 (DC Injection Braking Current).
cannot decelerate properly.
• Increase the b2-04 (DC Injection Braking Time at Stop).

■ OV or Speed Loss Occurs When Starting into a Rotating Load

Cause Possible Solutions

• Stop the motor using DC Injection braking. Restart the motor.
• Increase the value of b2-03 (DC Injection Braking Time at start).
The load is already rotating when the
• Enable Speed Search at start (b3-01 = “1”).
drive is trying to start it.
• Set a multi-function input terminal for external Speed Search command
(H1- =“61”or “62” during restart). Figure 4.17 on on page 130.

238 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 5.9 Troubleshooting without Fault Display

■ Output Frequency is not as High as Frequency Reference

Cause Possible Solutions

• Adjust the parameters used for the Jump Frequency function
Frequency reference is set within the (d3-01 through d3-03).
range of the Jump Frequency. • Enabling the Jump Frequency prevents the drive from outputting the
frequencies specified in the Jump Frequency range.
• Set the maximum output frequency and the upper limit for the frequency
Upper limit for the frequency reference reference to more appropriate values (E1-04, d2-01).
has been exceeded. • The following calculation yields the upper value for the output frequency
= E1-04 × d2-01 / 100
Large load triggered Stall Prevention • Reduce the load.
function during acceleration. • Adjust the Stall Prevention level during acceleration (L3-02).

■ Buzzing Sound from Motor at 2 kHz

Troubleshooting
Cause Possible Solutions
• If the output current rises too high at low speeds, the carrier frequency
automatically reduces and causes a whining or buzzing sound.
Exceeded 110% of the rated output • If the sound is coming from the motor, disable carrier frequency derating
current of the drive while operating at (L8-38 = “0”).
low speeds. • Disabling the automatic carrier frequency derating increases the chances
of an overload fault (oL2). Switch to a larger capacity motor if oL2 faults
5
occur too frequently.

■ Unstable Motor Speed when Using PM or IPM

Cause Possible Solutions

The motor code for PM (E5-01) is set
Set parameter E5-01 in accordance with the motor being used.
incorrectly. (Yaskawa motors only)
The drive is operating at less than 10% of Consult with Yaskawa about using a different type of motor when
the speed reference. attempting to operate at 10% of the speed reference.
Set and carefully adjust the following parameters in the order listed:
n8-45 (Speed Feedback Detection Suppression Gain)
Motor hunting occurs.
n8-55 (Load Inertia for PM Motors)
C4-02 (Torque Compensation Primary Delay Time)
Hunting occurs at start. Increase the S-curve time at the start of acceleration (C2-01).
If using a PM motor, set the correct motor code to E5-01.
Too much current is flowing through the
If using a specialized motor, set parameter E5-xx to the correct value
drive.
according to the Motor Test Report.

■ Motor Does Not Operate When the RUN Button on the Digital Operator is

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 239
5.9 Troubleshooting without Fault Display

Pressed

Cause Possible Solutions

The LOCAL/REMOTE mode is not Press the LOCAL/REMOTE button to switch. The LO/RE LED should be
selected properly. on for LOCAL mode.
A run command will not be issued. Exit to the drive mode and cycle the
The drive is not in drive mode.
run command.
• If the frequency reference is set below the frequency set in E1-09
The frequency reference is too low. (Minimum Output Frequency), the drive will not operate.
• Raise the frequency reference to at least the minimum output frequency.

■ Motor Does Not Operate When an External Run Command is Input

Cause Possible Solutions

The LOCAL/REMOTE mode is not Press the LOCAL/REMOTE button to switch. The LO/RE LED should be
selected properly. off for REMOTE mode.
A run command will not be issued. Exit to the Drive mode and cycle the
The drive is not in Drive Mode.
run command.
• If the frequency reference is set below the frequency set in E1-09
The frequency reference is too low. (Minimum Output Frequency), the drive will not operate.
• Raise the frequency reference to at least the minimum output frequency.

■ Motor Stops During Acceleration or When a Load is Connected

Cause Possible Solution

• The load is too heavy.
• The limit of motor response may be
reached during rapid acceleration. This Increase the acceleration time (C1-01) or reduce the motor load. Also,
may be a result of improper stall consider increasing the motor size and/or drive size.
prevention or automatic torque boost
function adjustment. (L3-01 = 2)

■ Motor Rotates in One Direction Only

Cause Possible Solution

"Reverse run prohibited" is selected. If
b1-04 (Reverse Prohibit Operation) is set
Set b1-04 = “0” to allow reverse run operation.
to 1 (reverse run prohibited), the drive
will not accept a reverse run command.

240 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 5.9 Troubleshooting without Fault Display

■ Motor Operates at a Higher Speed than the Speed Command

Cause Possible Solution

PID is enabled. If the PID mode is
enabled (b5-01 = 1 to 4), the drive output
frequency will change to regulate the
process variable to the target setpoint. If PID operation is not target, disable PID by setting b5-01 = “0”.
The PID can command a speed up to
maximum output frequency
(E1-04).

■ Poor Speed Control Accuracy Above Base Speed in Open-Loop Vector

Motor Control Method

Cause Possible Solution

Troubleshooting
The maximum output voltage of the
drive is determined by its input voltage.
Vector control uses voltage to control the
currents within the motor. If the vector
Use a motor with a lower rated voltage compared to the input voltage, or
control voltage reference value exceeds
change to flux vector control.
the drive output voltage capability, the
speed control accuracy will decrease
because the motor currents cannot be 5
properly controlled.

■ Peripheral Devices Affected by Drive Operation

Cause Possible Solutions

• Change the Carrier Frequency Selection (C6-02) to lower the carrier
frequency. This will help to reduce the amount of transistor switching
noise.
Radio frequency interference may be
• Install an Input Noise Filter at the input power terminals.
generated by drive output PWM
• Install an Output Noise Filter at the motor terminals.
waveform.
• Use conduit. Metal can shield electrical noise.
• Ground the drive and motor.
• Separate main circuit wiring from control wiring.

■ Ground Fault Interrupter Activates When Drive is Running

Cause Possible Solutions

• Change to a ground fault interrupter with a higher leakage current
The output of the drive is a series of high
detection level (such as, a sensitivity current of 200 mA or greater per
frequency pulses (PWM), so there is a
Unit, with an operating time of 0.1 s or more), or one that incorporates
certain amount of leakage current. This
high-frequency countermeasures.
may cause the ground fault interrupter to
• Change the Carrier Frequency Selection (C6-02) to lower the carrier
operate and cut off the drive input power.
frequency. Note: Leakage current increases in proportion to cable length.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 241
5.9 Troubleshooting without Fault Display

242 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 6
Periodic Inspection
& Maintenance
This chapter describes the periodic inspection and maintenance
of the drive to ensure that it receives the proper care to maintain
overall performance.

6.1 SECTION SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 244

6.2 INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 247
6.3 PERIODIC MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . 252
6.4 DRIVE COOLING FANS. . . . . . . . . . . . . . . . . . . . . . . . . 254
6.5 DRIVE REPLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . 258

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 243
6.1 Section Safety

6.1 Section Safety

DANGER
Electrical Shock Hazard
Do not connect or disconnect wiring while the power is on.
Failure to comply will result in death or serious injury.

WARNING
Electrical Shock Hazard
Do not operate equipment with covers removed.
Failure to comply could result in death or serious injury.
The diagrams in this section may show drives without covers or safety
shields to show details. Be sure to reinstall covers or shields before
operating the drives and run the drives according to the instructions
described in this manual.

Always ground the motor-side grounding terminal.

Improper equipment grounding could result in death or serious injury by
contacting the motor case.

Do not remove covers or touch circuit boards while the power is on.
Failure to comply could result in death or serious injury.

Do not allow unqualified personnel to perform work on the drive.

Failure to comply could result in death or serious injury.
Installation, maintenance, inspection, and servicing must be performed
only by authorized personnel familiar with installation, adjustment, and
maintenance of AC drives.

244 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 6.1 Section Safety

WARNING
Do not perform work on the drive while wearing loose clothing,
jewelry or without eye protection.
Failure to comply could result in death or serious injury.
Remove all metal objects such as watches and rings, secure loose clothing,
and wear eye protection before beginning work on the drive.

Do not touch any terminals before the capacitors have fully

discharged.
Failure to comply could result in death or serious injury.
Before wiring terminals, disconnect all power to the equipment. The

Periodic Inspection &

internal capacitor remains charged even after the power supply is turned
off. The charge indicator LED will extinguish when the DC bus voltage is

Maintenance
below 50 Vdc. To prevent electric shock, wait at least five minutes after all
indicators are off and measure the DC bus voltage level to confirm safe
level.

Fire Hazard
6
Tighten all terminal screws to the specified tightening torque.
Loose electrical connections could result in death or serious injury by fire
due to overheating of electrical connections.

Do not use an improper voltage source.

Failure to comply could result in death or serious injury by fire.
Verify that the rated voltage of the drive matches the voltage of the
incoming power supply before applying power.

Do not use improper combustible materials.

Failure to comply could result in death or serious injury by fire.
Attach the drive to metal or other noncombustible material.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 245
6.1 Section Safety

NOTICE
Observe proper electrostatic discharge procedures (ESD) when
handling the drive and circuit boards.
Failure to comply may result in ESD damage to the drive circuitry.

Never connect or disconnect the motor from the drive while the drive
is outputting voltage.
Improper equipment sequencing could result in damage to the drive.

Do not use unshielded cable for control wiring.

Failure to comply may cause electrical interference resulting in poor
system performance. Use shielded, twisted-pair wires and ground the
shield to the ground terminal of the drive.

Do not allow unqualified personnel to use the product.

Failure to comply could result in damage to the drive or braking circuit.
Carefully review instruction manual TOBPC72060000 when connecting a
braking option to the drive.

Do not modify the drive circuitry.

Failure to comply could result in damage to the drive and will void
warranty.
Yaskawa is not responsible for any modification of the product made by the
user. This product must not be modified.

Check all the wiring to ensure that all connections are correct after
installing the drive and connecting any other devices.
Failure to comply could result in damage to the drive.

246 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 6.2 Inspection

6.2 Inspection
Power electronics have limited life and may exhibit changed characteristics or performance
deterioration after years of use under normal conditions. To help avoid such problems, it is
important to perform preventive maintenance and periodic inspection on the drive.
Drives contain a variety of power electronics such as power transistors, semi-conductors,
capacitors, resistors, fans, and relays. The electronics in the drive serve a critical role in
maintaining proper motor control.
Follow the inspection lists provided in this chapter as a part of a regular maintenance
program.
Note: The drive will require more frequent inspection if it is placed in harsh environments,
such as:
-high ambient temperatures

Periodic Inspection &

-frequent starting and stopping
-fluctuations in the AC supply or load

Maintenance
-excessive vibrations or shock loading
-dust, metal dust, salt, sulfuric acid, chlorine atmospheres
-poor storage conditions.
Perform the first equipment inspection 3 months after installation. 6

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 247
6.2 Inspection

◆ Recommended Daily Inspection

Table 6.1 outlines the recommended daily inspection for Yaskawa drives. Check the
following items on a daily basis to avoid premature deterioration in performance or product
failure. Copy this checklist and mark the “Checked” column after each inspection.
WARNING! Electrical Shock Hazard. Do not connect or disconnect wiring while the power is on. Failure to
comply can result in serious personal injury. Before servicing the drive, disconnect all power to the
equipment. The internal capacitor remains charged even after the power supply is turned off. The charge
indicator LED will extinguish when the DC bus voltage is below 50 Vdc. To prevent electric shock, wait at
least five minutes after all indicators are OFF and measure the DC bus voltage level to confirm safe level.

Table 6.1 General Recommended Daily Inspection Checklist

Inspection
Category Inspection Points Corrective Action Checked

• Check the load coupling

• Inspect for abnormal oscillation or noise
Motor • Measure motor vibration
coming from the motor.
• Tighten all loose components
• Check for excessive load
• Inspect for abnormal heat generated
• Loose connections
Cooling from the drive or motor and visible
• Check for dirty heatsink or motor
discoloration.
• Ambient temperature
• Check for clogged or dirty fan.
Cooling • Inspect drive cooling fan operation.
• Check fan operation drive parameter.
• Verify the drive environment complies
• Eliminate the source of contaminants
Environment with the specifications listed in the
or correct poor environment.
Installation section of this manual.
• The drive output current should not be • Check for excessive load.
Load higher than the motor or drive rating for • Check the motor parameter settings of
an extended period of time. the drive.
• Correct the voltage or power supply to
Power Supply • Check main power supply and control
within nameplate specifications.
Voltage voltages.
• Verify all main circuit phases.

248 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 6.2 Inspection

◆ Recommended Periodic Inspection

Table 6.2 outlines the recommended periodic inspections for Yaskawa drive installations.
Periodic inspections should generally be checked every 3-6 months; however, the drive may
require more frequent inspection due to poor environments or rigorous use. Operating and
environmental conditions, along with experience in each application, will determine the
actual inspection frequency for each installation. Periodic inspection will help to avoid
premature deterioration in performance or product failure. Copy this checklist and mark the
“Checked” column after each inspection.
■ Periodic Inspection
WARNING! Electrical Shock Hazard. Do not connect or disconnect wiring while the power is on. Failure to
comply can result in serious personal injury. Before servicing the drive, disconnect all power to the
equipment. The internal capacitor remains charged even after the power supply is turned off. The charge
indicator LED will extinguish when the DC bus voltage is below 50 Vdc. To prevent electric shock, wait at
least five minutes after all indicators are OFF and measure the DC bus voltage level to confirm safe level.

Periodic Inspection &

Table 6.2 Periodic Inspection Checklist

Maintenance
Inspection Inspection Points Corrective Action Checked
Area
Main Circuit Periodic Inspection
• Overall check of the main power circuit Take appropriate actions
and ground terminals (e.g., tightening loose connections).
• Replace damaged components as
• Inspect equipment for discoloration from required.
6
overheating or deterioration. • The drive has few serviceable parts
• Inspect for damaged or deformed parts. and may require complete drive
replacement.
General
• Inspect enclosure door seal if present.
Replace components if cleaning is not
possible.
• Inspect for dirt, foreign particles, or dust
• Use dry air to clear away foreign
collection on components.
matter. Use a pressure of
39.2 x 104 to 58.8 x 104 Pa
(4 - 6 kg •cm2).
• Inspect wiring and connections for
Conductors and discoloration, damage, or heat stress.
• Repair or replace damaged wiring.
Wiring • Inspect wire insulation and shielding for
wear.
• Inspect terminals for stripped, damaged, • Tighten loose screws and replace
Terminals
or loose connections. damaged screws or terminals.
• Inspect contactors and relays for • Check coil voltage for over or under
Relays and excessive noise during operation. voltage conditions.
Contactors • Inspect coils for signs of overheating • Replace damaged removable relays
such as melted or cracked insulation. contactors or circuit board.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 249
6.2 Inspection

Inspection Inspection Points Corrective Action Checked

Area
• Minor discoloration may be
Braking • Inspect for discoloration of heat stress on acceptable.
Resistors or around resistors. • If discoloration exists check for loose
connections.
• Inspect for leakage, discoloration, or
• The drive has few serviceable parts
Electrolytic cracks.
and may require complete drive
(bus) Capacitors • Inspect the relief valve for swelling,
replacement.
rupture, or leakage.
• Use dry air to clear away foreign
Diodes and • Inspect for accumulation of dust or other matter.
IGBTs foreign particles on components. • Use a pressure of: 39.2 x 104 to 58.8 x
104 Pa (4 - 6 kg •cm2).
Motor Periodic Inspection
Operation • Check for increased vibration or • Stop the motor and contact qualified
Check abnormal noise. maintenance personnel as required.
Control Circuit Periodic Inspection
• Tighten loose screws and replace
• Inspect terminals for stripped, damaged damaged screws or terminals.
General or loose connections. • If terminals are integral to a circuit
• Check for tightness. board then board or drive replacement
may be required.
• Re-seat loose connectors.
• Replace PCBs if wiping or vacuuming
with anti-static vacuum cannot clean
the PCB.
• Inspect for unusual discoloration,
• Do not use solvents on PCBs.
burning or strange odor, noticeable rust
Printed Circuit • Use dry air to clear away foreign
or corrosion, proper seating of
Boards matter. Use a pressure of
connectors, dust, oil, or other
39.2 x 104 to 58.8 x 104 Pa
contamination.
(4 - 6 kg •cm2).
• The drive has few serviceable parts
and may require complete drive
replacement.
Cooling System Periodic Inspection
• Check for abnormal oscillation or • Replace as required.
unusual noise. • Refer to Drive Cooling Fans on
Cooling Fan
• Check for damaged or missing fan page 254 for information on cleaning
blades. or replacing the cooling fan.
• Use dry air to clear away foreign
• Inspect for dust or other foreign material matter.
Heatsink
collected on the surface. • Use a pressure of 39.2 x 104 to 58.8 x
104 Pa (4 - 6 kg•cm2).

250 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 6.2 Inspection

Inspection Inspection Points Corrective Action Checked

Area
• Inspect air intake and exhaust openings. • Visually inspect the area.
Air Duct They must be free from obstruction and • Clear obstructions and clean air duct
properly installed. as required.
LED Periodic Inspection
• Make sure the LED lights correctly.
• Make sure various components operate • Contact your Yaskawa representative
properly. if there is any trouble with the LED or
LEDs
• Inspect for dust or other foreign material keypad.
that may have collected on surrounding • Clean the LED.
components.

Note: Periodic inspections should be performed every one or two years. The drive, however, may
require more frequent inspection due to poor environments or rigorous use.

Periodic Inspection &

Maintenance
6

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 251
6.3 Periodic Maintenance

6.3 Periodic Maintenance

The drive has various "maintenance monitors". This feature provides advance maintenance
warning and eliminates the need to shut down the entire system for unexpected problems.
The drive allows the user to check the following maintenance periods.
• Cooling Fan
• Electrolytic Capacitors (Main Circuit)
• Inrush fuse
• IGBT

◆ Replacement Parts
Table 6.3 contains the estimated performance life of components that require replacement
during the life of the drive. Only use Yaskawa replacement parts for the appropriate drive
model and revision.
Table 6.3 Estimated Performance Life

Component Estimated Performance Life

Cooling Fan 10 years
Electrolytic Capacitors (Main Circuit) 10 years <1>
<1> The drive has few serviceable parts and may require complete drive replacement.

NOTICE: Estimated performance life based on specific usage conditions. These conditions are provided for
the purpose of replacing parts to maintain performance. Some parts may require more frequent replacement
due to poor environments or rigorous use.
Usage conditions for estimated performance life:
• Ambient temperature: Yearly average of 40°C
• Load factor: 80% maximum
• Operation time: 24 hours a day

■ Performance Life Monitors

The drive calculates the maintenance period for components that may require replacement
during the life of the drive. A percentage of the maintenance period is displayed on the LED
digital operator by viewing the appropriate monitor parameter.
When the maintenance period reaches 100%, there is increased risk that the drive may
malfunction. Yaskawa recommends checking the maintenance period regularly to ensure
maximum performance life.
Refer to Recommended Periodic Inspection on page 249 for more details.

252 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 6.3 Periodic Maintenance

Table 6.4 Performance Life Monitors Used for Component Replacement

Parameter Component Contents

Displays the accumulated operation time of the cooling fan, from 0 to
U4-03
99999 hours. This value is automatically reset to 0 once it reaches 999999.
Cooling Fan
Displays the accumulated cooling fan operation time as a percentage of the
U4-04
specified maintenance period (displayed in percent%).
Main Circuit (DC bus) Displays the accumulated time the capacitors are used as a percentage of
U4-05
Electrolytic Capacitors the specified maintenance period.
Inrush (pre-charge) Displays the number of times the drive is powered up as a percentage of
U4-06
relay the performance life of the inrush circuit.
U4-07 IGBT Displays the percentage of the maintenance period reached by the IGBTs.

■ Related Drive Parameters

Periodic Inspection &

Table 6.5 Maintenance Parameter Settings

Parameter Name Control Mode

Maintenance
Parameter Open Open Loop
Operator Display V/f Loop Vector for
Vector PM
o4-03 Cooling Fan Maintenance Setting (Operation Time) A A A
o4-05 Capacitor Maintenance Setting A A A
o4-07 Inrush Prevention Relay (pre-charge) Maintenance Setting A A A 6
o4-09 IGBT Maintenance Setting A A A

NOTICE: After replacing parts, reset the appropriate maintenance parameters (o4-03, o4-05, o4-07, and o4-
09) to 0. If these parameters are not reset, the function will continue to count down the performance life of
the new replaced components.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 253
6.4 Drive Cooling Fans

6.4 Drive Cooling Fans

NOTICE: Follow cooling fan replacement instructions. The cooling fan cannot operate properly when
installed incorrectly and could seriously damage the drive. To ensure maximum useful product life, replace
all cooling fans when performing maintenance.

Contact your Yaskawa representative or supplier to order replacement cooling fans as

required.
Some drive models have multiple cooling fans.
For drives with multiple cooling fans, replace all the fans when performing maintenance to
ensure maximum useful product life.

◆ Cooling Fan Replacement

The cooling fan is installed on the top of the drive. The cooling fan can easily be replaced
without tools or removal of the drive or enclosure parts.
WARNING! Electrical Shock Hazard. Do not connect or disconnect wiring while the power is on. Failure to
comply can result in serious personal injury. Before servicing the drive, disconnect all power to the
equipment. The internal capacitor remains charged even after the power supply is turned off. The charge
indicator LED will extinguish when the DC bus voltage is below 50 Vdc. To prevent electric shock, wait at
least five minutes after all indicators are OFF and measure the DC bus voltage level to confirm safe level.

CAUTION! Burn Hazard. Do not touch a hot drive heatsink. Failure to comply could result in minor or
moderate injury. Shut off the power to the drive when replacing the cooling fan. To prevent burns, wait at
least 15 minutes and ensure the heatsink has cooled down.

254 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 6.4 Drive Cooling Fans

■ Removing the Cooling Fan

1. Depress the right and left sides of the fan cover tabs and pull upward. Remove the
fan cover from the top of the drive. The figure illustrates a drive with a single cooling
fan.

A
B

Periodic Inspection &

Maintenance
Figure 6.1

A – Fan cover
B – Cooling fan
C – Tab

Figure 6.1 Remove the Cooling Fan Cover

2. Remove the fan cable carefully, disconnect the pluggable connector and remove the
fan.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 255
6.4 Drive Cooling Fans

■ Installing the Cooling Fan

NOTICE: Prevent Equipment Damage. Follow cooling fan replacement instructions. Improper cooling fan
replacement could result in the damage to equipment. When installing the replacement cooling fan into the
drive, make sure the fan is facing upwards.To ensure maximum useful product life, replace all cooling fans
when perfoming maintenance.

1. Install the replacement cooling fan into the drive, ensuring the alignment pins line
up, as shown in the figure below:
Figure 6.2

B
A

A – Label facing up
B – Back
C – Front

Figure 6.2 Cooling Fan Orientation

2. Ensure the connectors are properly connected and place the cable back into the
recess of the drive.

256 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 6.4 Drive Cooling Fans

Figure 6.3

A – Push the connectors together so no space remains between them.

Figure 6.3 Connectors

Periodic Inspection &

3. Align the left and right cover tabs to install the fan cover back on the top of the drive.
Note: Ensure that the left and right tabs are locked back into place.

Maintenance
6

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 257
6.5 Drive Replacement

6.5 Drive Replacement

◆ Serviceable Parts
The drive contains few serviceable parts. The following parts are considered replacement
parts on the drive:
• Main control board and I/O Terminal board I/O PCBs.
• Cooling fan(s)
• Front cover
Replace the drive if the main power circuitry is damaged. Contact your local Yaskawa
representative before replacing parts if the drive is still under warranty. Yaskawa reserves the
right to replace or repair the drive according to Yaskawa warranty policy.
WARNING! Electrical Shock Hazard. Do not connect or disconnect wiring while the power is on. Failure to
comply can result in serious personal injury. Before servicing the drive, disconnect all power to the
equipment. The internal capacitor remains charged even after the power supply is turned off. The charge
indicator LED will extinguish when the DC bus voltage is below 50 Vdc. To prevent electric shock, wait at
least five minutes after all indicators are OFF and measure the DC bus voltage level to confirm safe level.

◆ Terminal Board Overview

The drive has a modular I/O terminal block that facilitates quick drive replacement. The
terminal board contains on-board memory that stores all drive parameter settings and allows
the parameters to be saved and transferred to the replacement drive by disconnecting the
terminal board from the damaged drive then reconnecting the terminal board to the
replacement drive. There is no need to manually reprogram the replacement drive.
Figure 6.4

A – Charge LED
B – Terminal Board Screw
C – RemovableTerminal Board

Figure 6.4 Terminal Board

258 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 6.5 Drive Replacement

◆ Replacing the drive

WARNING! Electrical Shock Hazard. Never connect or disconnect wiring, remove connectors or option
cards, or replace the cooling fan while the power is on. Failure to comply may result in serious injury. Before
servicing, disconnect all power to the equipment. The internal capacitor remains charged even after the
power supply is turned off.

WARNING! Electrical Shock Hazard. Do not allow unqualified personnel to perform work on the drive.
Failure to comply could result in serious injury. Installation, maintenance, inspection and servicing must be
performed only by authorized personnel familiar with installation, adjustment and maintenance of AC drives.

NOTICE: Damage to Equipment. Observe proper electrostatic discharge procedures (ESD) when handling
the drive and circuit boards. Failure to comply may result in ESD damage to the drive circuitry.

Figure 6.5
1. Loosen the screw on the front of the drive and remove the front cover.

Periodic Inspection &

Maintenance
6
Figure 6.5 Remove Front Cover

2. Pull the pin on the ground terminal out of the removable terminal block.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 259
6.5 Drive Replacement

Figure 6.6

Pull out the

ground terminal
pin in the direction
indicated by
the arrow.
Cable

Terminal

Figure 6.6 Depress Plastic Tab

3. Push down the installation pin on the terminal board with a screwdriver

Push down
the
installation
pin with a
screwdriver.

4. While holding down the installation pin from step 3, slide the removable terminal
block in the direction of the arrows in the following figure.

260 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 6.5 Drive Replacement

Figure 6.7

Periodic Inspection &

Figure 6.7 Removing the Terminal Board
Figure 6.8

Maintenance
6

Figure 6.8 Removable Terminal Board disconnected from the drive

■ Terminal Board Replacement

1. Replace the removable terminal block on the drive according to Figure 6.9

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 261
6.5 Drive Replacement

Figure 6.9

Push down on the fixed pin at

the lower surface of the terminal
block, slide the terminal block
in the direction indicated by
the arrow.

Figure 6.9 Terminal Board Replacement

Figure 6.10
2. Ensure the terminal block is firmly fastened to the connector.

Connector

Figure 6.10 Terminal Board Installed

◆ Details on Terminal Board (TB) or Control Board (CNT)

Replacement
The drive Terminal Board retains drive parameter settings to significantly improve the ease
of drive replacement. Refer to Figure 6.11 for a flowchart to assist in board replacement.

262 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 6.5 Drive Replacement

When replacing the drive, or changing the Control Board or Terminal Board, the following
error codes may be encountered upon application of power:
• oPE04 Drive parameter settings need to be initialized or uploaded from the TB.
• CPF06 Drive specification does not match the replaced drive.
• oPE01 Drive parameter o2-04 kVA requires setting.
Procedural Notes:
1. When replacing the drive, control board or terminal board, make sure to confirm the kVA
setting, parameter o2-04 is correct upon initial power-up.
2. Perform an initialization (via parameter A1-03) to obtain the desired parameter settings.
3. In cases where a previously programmed terminal board is retained, initializing the drive
with a setting of A1-03 = 5550 may be desired to program the drive with previously
programmed settings (settings used prior to replacing the drive or control board).
Figure 6.11

Troubleshooting Fault Codes at

Terminal Board (TB) or Control Board (CNT) Replacement

Periodic Inspection &

START

Maintenance
YES “CPF06” Fault is
displayed upon drive
replacement

Note: Drive kVA Setting o2-04 = “FF”

NO inside a new Terminal Board

6
YES
Fault “oPE01”

NO

Set parameter o2-04 to match drive

nameplate rating

Fault “oPE04”
YES

NO
Fault “oPE04” drive parameter settings need
to be initialized or uploaded from the TB

Initialize the drive using Initialize the drive using

parameter A1-03 = 2220 or 3330 Set value = 2220 parameter A1-03
or 3330
Set value = 5550

Parameter setting values

are copied
TB to CNT

Ready

END

Figure 6.11 Troubleshooting Terminal Board or Control Board Replacement

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 263
6.5 Drive Replacement

264 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 7
Peripheral Devices
& Options
This chapter explains the installation of available peripheral
devices and options for the drive.

7.1 SECTION SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 266

7.2 PERIPHERAL DEVICES . . . . . . . . . . . . . . . . . . . . . . . . . 269
7.3 CONNECTING PERIPHERAL DEVICES . . . . . . . . . . . . . 270
7.4 INSTALLING PERIPHERAL DEVICES . . . . . . . . . . . . . . 271
7.5 COMMUNICATION OPTIONS . . . . . . . . . . . . . . . . . . . . . 285
7.6 CONNECTING AN OPTION CARD . . . . . . . . . . . . . . . . . 286

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 265
7.1 Section Safety

7.1 Section Safety

DANGER
Electrical Shock Hazard
Do not connect or disconnect wiring while the power is on.
Failure to comply will result in death or serious injury.
Disconnect all power to the drive, wait at least five minutes after all
indicators are off, measure the DC bus voltage to confirm safe level, and
check for unsafe voltages before servicing to prevent electric shock. The
internal capacitor remains charged even after the power supply is turned
off. The charge indicator LED will extinguish when the DC bus voltage is
below 50 Vdc.

WARNING
Electrical Shock Hazard
Do not operate equipment with covers removed.
Failure to comply could result in death or serious injury.
The diagrams in this section may show drives without covers or safety
shields to show details. Be sure to reinstall covers or shields before
operating the drives and run the drives according to the instructions
described in this manual.

Do not remove covers or touch circuit boards while the power is on.
Failure to comply could result in death or serious injury.

266 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 7.1 Section Safety

WARNING
Do not touch any terminals before the capacitors have fully
discharged.
Failure to comply could result in death or serious injury.
Before wiring terminals, disconnect all power to the equipment. The
internal capacitor remains charged even after the power supply is turned
off. The charge indicator LED will extinguish when the DC bus voltage is
below 50 Vdc. To prevent electric shock, wait at least five minutes after all
indicators are off and measure the DC bus voltage level to confirm safe
level.

Do not allow unqualified personnel to perform work on the drive.

Failure to comply could result in death or serious injury.

Peripheral Devices &

Installation, maintenance, inspection and servicing must be performed only
by authorized personnel familiar with installation, adjustment and
maintenance of AC drives.

Options
Do not perform work on the drive while wearing loose clothing,
jewelry or without eye protection.
Failure to comply could result in death or serious injury.
Remove all metal objects such as watches and rings, secure loose clothing 7
and wear eye protection before beginning work on the drive.

Always ground the motor-side grounding terminal.

Improper equipment grounding could result in death or serious injury by
contacting the motor case.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 267
7.1 Section Safety

WARNING
Do not change wiring or remove option cards while power is running
through the drive.
Failure to comply could result in death or serious injury.
Disconnect all power to the drive and check for unsafe voltages before
servicing.

Tighten all terminal screws to the specified tightening torque.

Loose electrical connections could result in death or serious injury by fire
due to overheating of electrical connections.

NOTICE
Observe proper electrostatic discharge procedures (ESD) when
handling the drive and circuit boards.
Failure to comply may result in ESD damage to the drive circuitry.

Never connect or disconnect the motor from the drive while the drive
is outputting voltage.
Improper equipment sequencing could result in damage to the drive.

268 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 7.2 Peripheral Devices

7.2 Peripheral Devices

The following table of peripheral devices lists the names of the various devices/options
available for Yaskawa drives. Contact Yaskawa or your Yaskawa agent to order these
peripheral devices.
• Peripheral Device Selection: Refer to Yaskawa catalog for EMC filter selection and part
numbers.
• Peripheral Device Installation: Refer to option manual for option installation
instructions.
Table 7.1 Available Peripheral Devices

Name
Surge Protector DIN Rail Attachments
DC Reactor NEMA Type 1 Kit
AC Reactor DriveWizard
Single-Phase 200 V Reactor Connection Cable for Engineering Tools

Peripheral Devices &

Braking Resistor DriveWorksEZ
Heatsink External Mounting Attachment (Side-by-Side)

The following table lists some of the available peripheral devices found in Table 7.2 along
with a picture of the device to help identify and describe situations that may require each

Options
device.
Table 7.2 Specific Peripheral Devices and Purposes

Device Purpose Device Purpose 7

Protects the drive when the
power supply is too large.
AC Braking For uses requiring dynamic
Required for power
Reactor resistor braking.
supplies greater than
600 kVA.
Surge
Harmonic suppression. Suppresses surge voltage.
protector
DC
DriveSelect
Reactor DriveWizard Software Software for selecting drive
Improves the power factor DriveWorksEZ
Engineering capacity, customizing and
of the power supply.
Tools programming the drive.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 269
7.3 Connecting Peripheral Devices

7.3 Connecting Peripheral Devices

Figure 7.1 illustrates how the drive and motor connect together with various peripheral
devices.
• Refer to peripheral device option manual for detailed installation instructions.
Figure 7.1

Engineering software tools

DriveSelect
DriveWizard
DriveWorksEZ

Power
supply

To serial comm port

Line
breaker PC
(MCCB)
or Drive
Leakage
breaker B1 B2
Surge
absorber

AC reactor Braking
resistor
unit

DC reactor

Ground
+1 +2
Input side
R/L1 S/L2 T/L3 U/T1 V/T2 W/T3
noise filter

Output side
noise filter
Motor

Ground

Figure 7.1 Connecting Peripheral Devices

270 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 7.4 Installing Peripheral Devices

7.4 Installing Peripheral Devices

This section describes the proper steps and precautions to take when installing or connecting
various peripheral devices to the drive.
• Refer to peripheral device manual for detailed installation instructions.
NOTICE: Use a class 2 power supply (UL standard) when connecting to the control terminals. Improper
application of peripheral devices could result in drive performance degradation due to improper power
supply.

◆ Installing a Molded Case Circuit Breaker (MCCB)

Install a n MCCB for line protection between the power supply and the main circuit power
supply input terminals R/L1, S/L2 and T/L3. This protects the main circuit and devices
wired to the main circuit while also providing overload protection.
Consider the following when selecting and installing a MCCB:
• The capacity of the MCCB should be 1.5 to 2 times the rated output current of the drive.

Peripheral Devices &

Use an MCCB keep the drive from faulting out instead of using overheat protection
(150% for one minute at the rated output current).
• If several drives are connected to one MCCB or an MCCB is shared with other
equipment, use a sequence that shuts the power OFF when errors are output by using
magnetic contactor (MC) as shown the following figure.

Options
• Install a 400/200 V transformer when using a 400 V class power supply input.
Figure 7.2

Drive
7
MCCB MC
R/L1
S/L2
T/L3
Three-Phase MC
AC200㨪240 V MB
50/60 Hz SA

Single-Phase MC
AC200㨪240 V
50/60 Hz MC

Figure 7.2 Connecting an MCCB (for Three-Phase 200 V Class)

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 271
7.4 Installing Peripheral Devices

Figure 7.3

Drive

MCCB MC
R/L1
S/L2
T/L3
Three-Phase MC
AC380㨪480 V MB
50/60 Hz SA
MC

MC
400 / 200 V
Transformer

Figure 7.3 Connecting an MCCB (for Three-Phase 400 V Class)

WARNING! Electrical Shock Hazard. Disconnect the MCCB and MC before wiring terminals. Failure to
comply may reslut in serious injury or death.

◆ Installing a Leakage Breaker

Drive outputs generate high-frequency leakage current as a result of high-speed switching.
Install a Ground Fault Circuit Interrupter (GFCI) on the input side of the drive to switch off
potentially harmful leakage current.
Factors in determining leakage current:
• Size of the AC drive
• AC drive carrier frequency
• Motor cable type and length
• EMI/RFI filter
In order to safely protect the drive system, select a breaker that senses all types of current
(AC and DC) and high frequency currents
Note: Choose a GFCI designed specifically for an AC drive. The operation time should be at least 0.1
second with sensitivity amperage of at least 200 mA per drive.
The output waveform of the drive may cause the leakage current to increase. This may, in turn,
cause the leakage breaker to malfunction. Take the following steps to correct the problem:
• Increase the sensitivity amperage.
• Lower the carrier frequency.

◆ Installing a Magnetic Contactor

■ Disconnecting the Power Supply
The drive can be shut off in the case of a fault in external equipment such as braking
resistors through use of a Magnetic Contactor (MC).
NOTICE: Install the MC on the input side of the drive when the drive should not automatically restart after
power loss. To get the full performance life out of the electrolytic capacitors and circuit relays, refrain from

272 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 7.4 Installing Peripheral Devices

switching the MC more than once every 30 minutes. Frequent use can damage the drive. Use the drive to
stop and start the motor.

■ Protecting the Braking Resistor or Braking Resistor Unit

Use an MC on the input side of the drive to protect a braking resistor or braking resistor unit
from overheat or fire.
WARNING! Fire Hazard. When using a braking unit, use a thermal relay on the braking resistors and
configure a fault contact output for the braking resistor unit to disconnect drive main power via an input
contactor. Inadequate braking circuit protection could result in death or serious injury by fire from
overheating resistors.

◆ Connecting an AC or DC Reactor
AC and DC reactors suppress surges in current and improve the power factor on the input
side of the drive.
To better suppress harmonic current, use an AC reactor and DC reactor together.
Use a DC reactor or AC reactor or both:

Peripheral Devices &

• To suppress harmonic current or improve the power factor of the power supply.
• When using an advancing capacitor switch.
• With a large capacity power supply transformer (over 600 kVA).

Options
Note: Use an AC or DC reactor when also connecting a thyristor converter (such as a DC drive) to the
same power supply system, regardless of the conditions of the power supply.

■ Connecting an AC Reactor
Figure 7.4
7
C D
A B
U X R/L1
V Y S/L2
W Z T/L3

A – Power supply C – AC reactor

B – MCCB D – Drive

Figure 7.4 Connecting an AC Reactor

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 273
7.4 Installing Peripheral Devices

■ Connecting a DC Reactor
Ensure the jumper between terminals +1 and +2 (terminals are jumpered for shipment) is
removed when connecting a DC reactor. The jumper must be installed if no DC reactor is
used. Refer to Figure 7.5 for an example of DC reactor wiring.
Figure 7.5

C
A B
R/L1
S/L2
T/L3

+1 +2

A – Power supply C – Drive

B – MCCB D – DC reactor

Figure 7.5 Connecting a DC Reactor

◆ Connecting a Surge Protector

A surge protector suppresses surge voltage generated from switching an inductive load near
the drive. Inductive loads include magnetic contactors, relays, valves, solenoids and brakes.
Always use a surge protector or diode when operating with an inductive load.
Note: Never connect a surge protector to the drive output.

◆ Connecting a Noise Filter

■ Input-Side Noise Filter
Drive outputs generate noise as a result of high-speed switching. This noise flows from
inside the drive back toward the power supply, possible affecting other equipment. Installing
a noise filter to the input side of the drive can reduce the amount of noise flowing back into
the power supply. This also prevents noise from entering the drive from the power supply.
• Use a noise filter specifically designed for AC drives.
• Install the noise filter as close as possible to the drive.

274 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 7.4 Installing Peripheral Devices

Figure 7.6

B C
A MCCB
1 3 R/L1

2 4 S/L2

MCCB

A – Power supply C – Drive

B – Input-side noise filter D – Other control device
Model: LNFD-††

Figure 7.6 Input-Side Noise Filter (Single-Phase 200 V)

Peripheral Devices &

Figure 7.7

B C
MCCB
A R U R/L1

Options
S/L2
S V
T/L3
T W

E
7
MCCB

A – Power supply C – Drive

B – Input-side noise filter D – Other control device
Model: LNFD-††

Figure 7.7 Input-Side Noise Filter (Three-Phase 200/400 V)

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 275
7.4 Installing Peripheral Devices

■ Output-Side Noise Filter

A noise filter on the output side of the drive reduces inductive noise and radiated noise.
Figure 7.8 illustrates an example of output-side noise filter wiring.
NOTICE: Do not connect phase-advancing capacitors or LC/RC noise filters to the output circuits. Improper
application of noise filters could result in damage to the drive.
Figure 7.8

B C
A MCCB
R/L1 U/T1 1 4
S/L2 V/T2 2 5 D
T/L3 W/T3 3 6

A – Power supply C – Output-side noise filter

B – Drive D – Motor

Figure 7.8 Output-Side Noise Filter

TERMS
Radiated Electromagnetic waves radiated from the drive and cables create noise
noise: throughout the radio bandwidth that can affect devices.

Induced Noise generated by electromagnetic induction can affect the signal line and
noise: may cause the controller to malfunction.

276 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 7.4 Installing Peripheral Devices

Preventing Induced Noise

Use a noise filter on the output side or use shielded cables. Lay the cables at least 30 cm
away from the signal line to prevent induced noise.
Figure 7.9

B
A MCCB
C
R/L1 U/T1
S/L2 V/T2
D
T/L3 W/T3

G
F

A – Power supply E – Separate at least 30 cm

B – Drive F – Controller
C – Shielded motor cable G – Signal line

Peripheral Devices &

D – Motor H –

Figure 7.9 Preventing Induced Noise

Reducing Radiated/Radio Frequency Noise

Options
The drive, input lines, and output lines generate radio frequency noise. Use noise filters on
input and output sides and install the drive in a metal enclosure panel to reduce radio
frequency noise.
Figure 7.10
Note: The cable running between the drive and motor should be as short as possible. 7
A

B MCCB C D E F
R/L1 U/T1
S/L2 V/T2 G
T/L3 W/T3

A – Metal enclosure E – Noise filter

B – Power supply F – Shielded motor cable
C – Noise filter G – Motor
D – Drive H –

Figure 7.10 Reducing Radio Frequency Noise

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 277
7.4 Installing Peripheral Devices

◆ EMC Filter Installation

This drive is tested according to European standards EN61800-3 and it complies with the
EMC guidelines. The following conditions must be met to ensure continued compliance
with guidelines.
• EMC Filter Selection: Refer to Yaskawa catalog for EMC filter selection and part
numbers.
• EMC Filter Installation: Refer to option manual for option installation instructions.
■ Installation Method
Verify the following installation conditions to ensure that other devices and machinery used
in combination with this drive also comply with EMC guidelines.
1. Install an EMC noise filter to the input side specified by Yaskawa for compliance
with European standards.
2. Place the drive and EMC noise filter in the same enclosure.
3. Use braided shield cable for the drive and motor wiring or run the wiring through a
metal conduit.
4. Keep wiring as short as possible. Ground the shield on both the drive side and the
Figure 7.11
motor side (Figure 7.11).
B

A D C
U/T1 U
V/T2 V
M
W/T3 W

A – Drive D – Metal conduit

B – 20 m max cable length between E – Ground wire should be as short as
drive and motor possible.
C – Motor

Figure 7.11 Installation Method

5. Ground the largest possible surface area of the shield to the metal conduit when
using braided shield cable. Yaskawa recommends using a cable clamp
(Figure 7.12).

278 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 7.4 Installing Peripheral Devices

Figure 7.12

C B

A – Braided shield cable C – Cable clamp (conductive)

B – Metal panel

Figure 7.12 Ground Area

Peripheral Devices &

Options
7

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 279
7.4 Installing Peripheral Devices

Three-Phase 200 V / 400 V Class

Figure 7.13

L3 A
L2

L1
PE
H

B
C
D

L3 L2 L1

J E
R/L1 S/L2 T/L3 U/T1 V/T2 W/T3

D
D
I

H F

A
G

A – Ground the cable shield F – Motor cable (braided shield cable,

max. 20 m)
B – Enclosure panel G – Motor
C – Metal plate H – Cable clamp
D – Grounding surface (remove any I – Max. distance between drive and
paint or sealant) noise filter
E – Drive J – EMC noise filter

Figure 7.13 EMC Filter and Drive Installation for CE Compliance

(Three-Phase 200 V / 400 V Class)

280 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 7.4 Installing Peripheral Devices

Single-Phase 200 V Class

Figure 7.14

A
L2

L1
PE

B
C
D

L3 L2 L1

Peripheral Devices &

E
R/L1 S/L2 T/L3 U/T1 V/T2 W/T3

D
D

Options
I

F
7
H

A
G

A – Ground the cable shield F – Motor cable (braided shield cable,

max. 20 m)
B – Enclosure panel G – Motor
C – Metal plate H – Cable clamp
D – Grounding surface (remove any I – Max. distance between drive and
paint or sealant) noise filter
E – Drive J – EMC noise filter

Figure 7.14 EMC Filter and Drive Installation for CE Compliance

(Single-Phase 200 V Class)

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 281
7.4 Installing Peripheral Devices

◆ Installing a Motor Thermal Overload (OL) Relay on the Drive

Output
Motor thermal overload relays protect the motor by disconnecting power lines to the motor
due to a motor overload condition.
Install a motor thermal overload relay between the drive and motor:
• When operating multiple motors on a single AC drive.
• When using a power line bypass to operate the motor directly from the power line.
It is not necessary to install a motor thermal overload relay when operating a single motor
from a single AC drive. The AC drive has UL recognized electronic motor overload
protection built into the drive software..
Note: Disable the motor protection function (L1-0 1 = “0”) when using an external motor
thermal overload relay. The relay should shut off main power on the input side of the
main circuit when triggered.
Special application precautions should be considered when using motor thermal overload
relays on the output of AC drives. The following may occur if a motor thermal OL relay is
connected to the output of an AC drive (between the drive and the motor) when the carrier
frequency is high and the wiring between the motor and the drive is long:
• Thermal relay nuisance trips occur.
• The thermal relay may be damaged due to excessive heat loss.
Some considerations involving AC drives and use of thermal overload relays:
1. Low speed motor operation
2. Use of multiple motors on a single AC drive
3. Motor cable length greater than 50 meters (164 feet)
4. Voltage boost and high torque V/f pattern settings
5. Nuisance tripping resulting from high AC drive carrier frequency
■ General Precautions to Prevent Tripping of Motor Thermal Overload
Relays
Low Speed Operation and Motor Thermal OL Relays
Generally, thermal relays are applied on general-purpose motors. When general-purpose
motors are driven by AC drives, the motor current is approximately 5 ~ 10% greater than if
driven by the commercial power supply. In addition, the cooling capacity of a motor with a
shaft-driven fan decreases when operating at low speeds. Even if the load current is within
the motor rated value, motor overheating may occur. A thermal relay cannot effectively
protect the motor due to the reduction of cooling at low speeds. For this reason, apply the
UL-recognized electronic thermal overload protection function built into the drive whenever
possible.

282 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 7.4 Installing Peripheral Devices

UL recognized electronic thermal overload function of the drive: Speed-dependent

heat characteristics are simulated using data from standard motors and force-ventilated
motors. The motor is protected from overload using this function.
Using One Drive with Multiple Motors
Turn off the electronic thermal overload function. Please refer to the appropriate product
instruction manual to determine which parameter disables this function.
The UL recognized electronic thermal overload function of the drive cannot be applied
when using multiple motors on one drive. The electronic thermal function is calculated
using the output current of the drive. Individual motor currents cannot be determined
using the output current of the drive. Therefore, a thermal relay is required for each
motor connected to the drive.
Wiring Length Greater Than 50 meters (164 feet)
When motor wiring is longer than 164 feet (50 meters), nuisance tripping of the thermal
relaymay occur if a high carrier frequency is used. Due to increased high frequency leakage
current the thermal relay element may overheat due to surface skin effect. Therefore, reduce
the carrier frequency.

Peripheral Devices &

The following should be considered for long motor cable length applications:
1. For a single motor drive, use the electronic thermal overload function of the drive (thermal
relay not required).
2. For multiple motor drives:

Options
Lower the carrier frequency according to Figure 7.15 or correct the motor thermal OL
relay adjustment according the Table 7.3.
Figure 7.15

Figure 7.15 Criteria for Setting Carrier Frequency

Voltage Boost and High Torque V/f Pattern Settings

The V/f pattern and voltage boost settings may impact motor heating. Improperly adjusted
V/f patterns or torque compensation settings may cause over-excitation of the motor,

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 283
7.4 Installing Peripheral Devices

resulting in additional motor heating. Unintentional triggering of the overload device may
also occur. Therefore, do not use high starting torque V/f patterns or use excessive voltage
boost settings unless absolutely necessary.
Correcting Nuisance Tripping Resulting from High AC Drive Carrier Frequency
Thermal overload element heating is influenced by carrier frequency and lead length.
Current waveforms generated by PWM drives tend to create additional temperature rise in
overload relays. Therefore, it may be necessary to increase the trip level setting by the
factors listed in Table 7.3 when encountering nuisance triggering of the relay. Confirm an
actual overload condition is not present prior to increasing the trigger level.
WARNING! Risk of Fire. Confirm an actual motor overload condition is not present prior to increasing the
thermal OL trip setting. Check local electrical codes before making adjustments to motor thermal overload
settings.

Example:A thermal OL relay with an adjustment range of 1.1 to 1.6 A is used with a drive
working with 8 kHz carrier frequency. The motor rated current is 1.2 A. The overload trip
level may be corrected to: 1.2 A x 1.21 = 1.45 A
Table 7.3 shows recommended correction factors for the motor protection device trigger
level based on adjustment range and carrier frequency of the drive.
Table 7.3 Motor Protection Device Correction Factors

Adjustment Range/ Rated Drive Carrier Frequency Setting (KHz)

Current
2 4 6 8 10 12 14 16
3.2 to 50 A 1.07 1.12 1.16 1.18 1.19 1.21 1.22 1.23
0.5 to 2.5 A 1.08 1.13 1.17 1.21 1.24 1.26 1.28 1.29
0.32 to 0.4 A 1.09 1.15 1.21 1.25 1.29 1.33 1.35 1.37
0.16 to 0.25 A 1.10 1.17 1.24 1.28 1.33 1.38 1.42 1.46

System Component Compatibility

Thoroughly review the application requirements to ensure compatibility of the selected
components (motor, speed range, application speed-torque requirements).

284 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 7.5 Communication Options

7.5 Communication Options

Table 7.4 gives detailed information about the available option cards that allow Yaskawa
drives to connect to various communications networks. Consult the table to determine which
option cards may be necessary for a given environment. Contact Yaskawa or your Yaskawa
agent to order option cards.
• Option Card Selection: Refer to Yaskawa catalog for option card selection and part
numbers.
• Option Card Installation: Refer to option card manual for option card installation
instructions.
Table 7.4 Available Option Cards

Option Card Model Function Manual

Allows the drive to connect to a CC-Link network. A host
controller starts and stops the drive and allows the user to
CC-Link SI-C2 Contact Yaskawa
edit and reference parameter settings (output frequency,
output current, etc.) over the network.

Peripheral Devices &

Options
7

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 285
7.6 Connecting an Option Card

7.6 Connecting an Option Card

The drive can communicate with other devices through a specially designed option card. The
following section describes how to install an option card.
Refer to option card manual for detailed installation instructions.
Note: Refer to Available Option Cards on page 285 for a list of option cards for use with this product.

◆ Verifying Option Card and Product Type

Figure 7.16

A G
B

C
H
D

E
I
F

A – Option card F – Wire through-hole

B – Option card cover installation G – Option card cover
screw holes
C – Tabs for mounting front cover H – Cover screw
D – Comm. connector (CN1) I – Ground lead
E – Ground lead connection J –

Figure 7.16 Option Card

286 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 7.6 Connecting an Option Card

◆ Connecting the Option Card

Figure 7.17
1. Loosen the screw on the front cover of the drive to remove the cover.

Figure 7.17 Remove Cover

2. Remove the terminal cover. Connect the lead from the option card to the drive
ground terminal.

Peripheral Devices &

Figure 7.18

Options
A 7
B
C

A – Ground terminal C – Terminal cover

B – Ground lead D –

Figure 7.18 Connect Lead

3. Reattach the terminal cover.

4. Attach the option card to the drive.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 287
7.6 Connecting an Option Card

Figure 7.19

A – Line up the tab with the mounting B – Line up the tab with the mounting
hole. hole.

Figure 7.19 Attach Option Card

Note: Gently pack wires to fit behind the left and right side of the cover into the provided recess.
5. Connect the lead from the drive ground terminal to the same terminal as the option
card lead.
The option card lead should exit through the holes provided on the underside of the
drive as it gets routed passed the ground terminal.
Figure 7.20

E
D A

B
C
A – Drive ground terminal D – Ground lead through-hole
B – Route the lead wire on the inside of E – Ground lead
the lower cover.
C – Ground lead

Figure 7.20 Lead Wire Connection

288 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 7.6 Connecting an Option Card

Figure 7.21
6. Reattach the option card cover.

A – Align the tab with the mounting hole.

Figure 7.21 Reattach Cover

Peripheral Devices &

Options
7

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 289
7.6 Connecting an Option Card

290 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 A
Specifications

A.1 HEAVY DUTY AND NORMAL DUTY RATINGS . . . . . . . 292

A.2 SINGLE/THREE-PHASE 200 V CLASS DRIVE . . . . . . . 293
A.3 THREE-PHASE 400 V CLASS DRIVES . . . . . . . . . . . . . 296
A.4 DRIVE SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . 298
A.5 DRIVE WATTS LOSS DATA . . . . . . . . . . . . . . . . . . . . . . 302
A.6 DRIVE DERATING DATA . . . . . . . . . . . . . . . . . . . . . . . . 305

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 291
A.1 Heavy Duty and Normal Duty Ratings

A.1 Heavy Duty and Normal Duty Ratings

The capacity of the drive is based on two types of load characteristics: Heavy Duty (HD) and
Normal Duty (ND).
Refer to Table A.1 for the differences between HD and ND. Specifications for capacity
ratings appear are listed on the following pages.
Table A.1 Selecting the Appropriate Load Rating

Setting
Parameter Rated Output Current Overload Tolerance Carrier Frequency
C6-01
0: Heavy Duty HD Rating 2-15 kHz
150% rated output current for 60 s
(default) varies by model <1> varies by model
1: Normal Duty ND Rating 120% rated output current for 60 s.
2 kHz, Swing PWM
(default) varies by model <1> Varies by model <1>

<1> The following pages list information on rating changes based on drive model.

TERMS
HD and ND
• HD refers to applications requiring constant torque output, while ND refers to
applications with variable torque needs.
• The drive allows the user to select HD or ND torque depending on the application.
Fans, pumps, and blowers should use ND (C6-01 = “1”), and other applications
generally use HD (C6-01 = “0”).
Swing PWM
• Swing PWM equivalent to a 2 kHz audible noise. This function turns the motor
noise into a less obtrusive white noise.
Note: Differences between HD ratings and ND ratings for the drive include rated input and output
current, overload capacity, carrier frequency, and current limit. The default setting is for ND
(C6-01=1).

292 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 A.2 Single/Three-Phase 200 V Class Drive

A.2 Single/Three-Phase 200 V Class Drive

Table A.2 Power Ratings

Item Specification
Three-Phase: CIMR-V 2A 0001 0002 0004 0006 0010 0012 0020
Single-Phase: CIMR-V BA <1> 0001 0002 0003 0006 0010 0012 -
Maximum Motor Size Allowed ND Rating 0.13 0.25 0.5/0.75 1.0/1.5 2.0/3.0 3.0 5.0
(HP) <2> HD Rating 0.13 0.25 0.5/0.75 0.75/1.0 1.5/2.0 3.0 5.0
Three- ND Rating 1.1 1.9 3.9 7.3 10.8 13.9 24.0
Input Current Phase HD Rating 0.7 1.5 2.9 5.8 7.5 11.0 18.9
Input
(A) <3> Single- ND Rating 2.0 3.6 7.3 13.8 20.2 24.0 –
Phase HD Rating 1.4 2.8 5.5 11.0 14.1 20.6 –
Rated Output Capacity ND Rating 0.5 0.7 1.3 2.3 3.7 4.6 7.5
(kVA) <4> HD Rating 0.3 0.6 1.1 1.9 3.0 4.2 6.7
ND
1.2 1.9 3.5 (3.3) 6.0 9.6 12.0 19.6
Output Current (A) Rating <5>
HD Rating 0.8 <6> 1.6 <6> 3.0 <6> 5.0 <6> 8. <7> 11.0 <7> 17.5 <7>
ND Rating: 120% of rated output current for 1 minute
Output HD Rating: 150% of rated output current for 1 minute
Overload Tolerance
(Derating may be required for applications that start and stop

Specifications
frequently)
Carrier Frequency 2 kHz (user-set, 2 to 15 kHz)
Three-phase power: Three-phase 200 to 240 V Single-phase power:
Max Output Voltage (V) Three-phase 200 to 240 V
(both proportional to input voltage)
Max Output Frequency (Hz)
Rated Voltage
400 Hz (user-adjustable)
Three-phase power: Three-phase 200 to 240 V 50/60 Hz
A
Power Rated Frequency Single-phase power: 200 to 240 V 50/60 Hz
Supply Allowable Voltage Fluctuation -15 to 10%
Allowable Frequency Fluctuation ±5%
Harmonic DC
Optional
Countermeasures Reactor
Three- ND Rating 13.0 17.1 29.4 44.7 77.5 91.7 145.0
Phase HD Rating 11.6 16.7 27.6 43.3 78.6 100.7 153.8
Heat Generation (W)
Single- ND Rating 13.5 17.3 29.0 49.5 81.5 98.4 –
Phase HD Rating 11.7 16.8 27.6 50.5 80.7 104.8 161.9

<1> Drives with single-phase power supply inputs output three-phase power, and cannot run a single-phase motor.
<2> The motor capacity (HP) refers to a NEC rated 4-pole motor. The rated output current of the drive output amps
should be equal to or greater than the motor rated current.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 293
A.2 Single/Three-Phase 200 V Class Drive

<3> Input current rating varies depending on the power supply transformer, input reactor, wiring connections, and
power supply impedance.
<4> Rated motor capacity is calculated with a rated output voltage of 230 V.
<5> Carrier frequency is set to 2 kHz. Current derating is required in order to raise the carrier frequency.
<6> Carrier frequency is set to 10 kHz. Current derating is required in order to raise the carrier frequency.
<7> Carrier frequency is set to 8 kHz. Current derating is required in order to raise the carrier frequency.

Table A.3 Power Ratings Continued

Item Specification
Three-Phase: CIMR-V 2A 0030 0040 0056 0069
Single-Phase: CIMR-V BA <1> - - - -
ND Rating 10.1 14.8 20.1 24.8
Maximum Motor Size Allowed (HP) <2>
HD Rating 7.4 10.1 14.8 20.1
ND Rating 34.7 50.9 69.4 85.6
Three-Phase
Input Current HD Rating 26.0 35.4 51.9 70.8
Input
(A) <3> ND Rating - - - -
Single-Phase
HD Rating - - - -
Rated Output Capacity ND Rating 11.4 15.2 21.3 26.3
(kVA) <4> HD Rating 9.5 12.6 17.9 22.9
ND Rating <5> 30.0 40.0 56.0 69.0
Output Current (A)
HD Rating 25.0 <7> 33.0 <7> 47. <7> 60.0 <7>
ND Rating: 120% of rated output current for 1 minute
HD Rating: 150% of rated output current for 1 minute
Output Overload Tolerance
(Derating may be required for applications that start and
stop frequently)
Carrier Frequency 2 kHz (user-set, 2 to 15 kHz)
Three-phase power: Three-phase 200 to 240 V
Max Output Voltage (V) Single-phase power: Three-phase 200 to 240 V (both
proportional to input voltage)
Max Output Frequency (Hz) 400 Hz (user-adjustable)
Rated Voltage Three-phase power: Three-phase 200 to 240 V 50/60 Hz
Power Rated Frequency Single-phase power: 200 to 240 V 50/60 Hz
Supply Allowable Voltage Fluctuation -15 to 10%
Allowable Frequency Fluctuation ±5%
DC
Harmonic Countermeasures Optional
Reactor
ND Rating - - - -
Three Phase
HD Rating 335.3 379.5 509.7 646.2
Heat Generation (W)
ND Rating 303.7 321.3 465.2 589.1
Single Phase
HD Rating - - - -

<1> Drives with single-phase power supply inputs output three-phase power, and cannot run a single-phase motor.

294 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 A.2 Single/Three-Phase 200 V Class Drive

<2> The motor capacity (kW) refers to a Yaskawa 4-pole motor. The rated output current of the drive output amps
should be equal to or greater than the motor rated current.
<3> Input current rating varies depending on the power supply transformer, input reactor, wiring connections, and
power supply impedance.
<4> Rated motor capacity is calculated with a rated output voltage of 220 V.
<5> Carrier frequency is set to 2 kHz. Current derating is required in order to raise the carrier frequency.
<7> Carrier frequency is set to 8 kHz. Current derating is required in order to raise the carrier frequency.

Note: Differences between Heavy Duty (HD) ratings and Normal Duty (ND)ratings for the drive
include rated input and output current, overload capacity, carrier frequency, current limit, and
maximum output frequency. Set parameter C6-01 to “0” for HD ratings or “2” for ND ratings.
Default is ND (C6-01 = 1).

Specifications
A

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 295
A.3 Three-Phase 400 V Class Drives

A.3 Three-Phase 400 V Class Drives

Table A.4 Power Ratings

Item Specification
CIMR-V 4A 0001 0002 0004 0005 0007 0009 0011
Maximum Applicable Motor Capacity ND Rating 0.25 0.5/0.75/1.0 1.5/2.0 3.0 3.0 5.0 7.5
(HP) <1> HD Rating 0.25 0.5/0.75 1.0/1.5/2.0 3.0 3.0 5.0 5.0
ND Rating 1.2 2.1 4.3 5.9 8.1 9.4 14.0
Input Input Current (A) <2>
HD Rating 1.2 1.8 3.2 4.4 6.0 8.2 10.4
ND Rating <4> 0.9 1.6 3.1 4.1 5.3 6.7 8.5
Output Current (kVA) <3>
HD Rating <5> 0.9 1.4 2.6 3.7 4.2 5.5 7.0
ND Rating <4> 1.2 2.1 4.1 5.4 6.9 8.8 11.1
Output Current (A)
HD Rating <5> 1.2 1.8 3.4 4.8 5.5 7.2 9.2
ND Rating: 120% of rated output current for 60 s
Output HD Rating: 150% of rated output current for 60 s
Overload Tolerance
(Derating may be required for applications that start and
stop frequently)
Carrier Frequency <3> 2 kHz (user-adjustable from 2 to 15 kHz)
Three-phase: @380 to 480 V (proportional to input
Maximum Output Voltage (V)
voltage)
Maximum Output Frequency (Hz) 400 Hz (user-adjustable)
Rated Voltage Rated Frequency Three-phase: 380 to 480 V 50/60 Hz
Power
Allowable Voltage Fluctuation -15 to 10%
Supply
Allowable Frequency Fluctuation ±5%
Harmonic
DC Reactor Optional
Countermeasures
ND Rating 19.6 32.4 47.3 66.3 87.0 95.1 127.7
Heat Generation (W)
HD Rating 30.6 43.8 60.2 96.9 111.7 117.5 148.7

<1> The motor capacity (HP) refers to a NEC 4-pole motor. The rated output current of the drive output amps should
be equal to or greater than the motor rated current.
<2> Input current rating varies depending on the power supply transformer, input reactor, wiring conditions, and
power supply impedance.
<3> Rated motor capacity is calculated with a rated output voltage of 460 V.
<4> Carrier frequency is set to 2 kHz. Current derating is required in order to raise the carrier frequency.
<5> Carrier frequency is set to 8 kHz. Current derating is required in order to raise the carrier frequency.

296 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 A.3 Three-Phase 400 V Class Drives

Table A.5 Power Ratings Continued

Item Specification
CIMR-V 4A 0018 0023 0031 0038
Maximum Applicable Motor Capacity ND Rating 10.1 14.8 20.1 24.8
(HP) <1> HD Rating 7.4 10.1 14.8 20.1
ND Rating 20.0 24.0 38.0 44.0
Input Input Current (A) <2>
HD Rating 15.0 20.0 29.0 39.0
ND Rating <4> 13.3 17.5 23.6 29.0
Output Current (kVA) <3>
HD Rating <5> 11.3 13.7 18.3 23.6
ND Rating <4> 17.5 23.0 31.0 38.0
Output Current (A)
HD Rating <5> 14.8 18.0 24.0 31.0
ND Rating: 120% of rated output current for 60 s
Output HD Rating: 150% of rated output current for 60 s
Overload Tolerance
(Derating may be required for applications that start and
stop frequently)
Carrier Frequency <3> 2 kHz (user-adjustable from 2 to 15 kHz)
Three-phase: @380 to 480 V (proportional to input
Maximum Output Voltage (V)
voltage)
Maximum Output Frequency (Hz) 400 Hz (user-adjustable)
Rated Voltage Rated Frequency Three-phase: 380 to 480 V 50/60 Hz

Specifications
Power
Allowable Voltage Fluctuation -15 to 10%
Supply
Allowable Frequency Fluctuation ±5%
Harmonic
DC Reactor Optional
Countermeasures
ND Rating 261.3 321.1 433.6 475.0
Heat Generation (W)
HD Rating 228.7 285.2 372.8 445.7 A
<1> The motor capacity (kW) refers to a Yaskawa 4-pole motor. The rated output current of the drive output amps
should be equal to or greater than the motor rated current.
<2> .Input current rating varies depending on the power supply transformer, input reactor, wiring conditions, and
power supply impedance.
<3> Rated motor capacity is calculated with a rated output voltage of 440 V.
<4> Carrier frequency is set to 2 kHz. Current derating is required in order to raise the carrier frequency.
<5> Carrier frequency is set to 8 kHz. Current derating is required in order to raise the carrier frequency.

Note: Differences between Heavy Duty ratings and Normal Duty ratings for the drive include rated
input and output current, overload capacity, carrier frequency, current limit, and maximum
output frequency. Set parameter C6-01 to “0” for Heavy Duty ratings or “2” for Normal Duty
ratings. The default is Normal Duty (C6-01 = 1).

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 297
A.4 Drive Specifications

A.4 Drive Specifications

Note: Perform rotational Auto-Tuning to obtain OLV performance specifications.
Note: For optimum performance life of the drive, install the drive in an environment that meets the
environmental conditions.

298 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 A.4 Drive Specifications

Item Specification
The following control methods are available:
Control Method Open Loop Vector Control (current vector), V/f Control, and PM Open Loop
Vector for (for use with SPM and IPM)
Frequency Control
0.01 to 400 Hz
Range
Digital input: within ±0.01% of the max output frequency (-10 to +50 °C)
Frequency Accuracy
Analog input: within ±0.5% of the max output frequency (25°C ±10 °C)
Frequency Setting Digital inputs: 0.01 Hz
Resolution Analog inputs: 1/1000 of maximum output frequency
Output Frequency
1/220 of maximum output frequency
Resolution
Main frequency reference: 0 to +10 Vdc (20 kΩ), 4 to 20 mA (250 Ω), 0 to
Frequency Setting
20 mA (250 Ω)
Signal
Main speed reference: Pulse Train Input (max 33 kHz)
200%/0.5 Hz (Open Loop Vector Control, HD rating, IM of 3.7 kW or
Starting Torque
smaller), 50%/6 Hz (PM Open Loop Vector Control)
Speed Control 1:100 (Open Loop Vector Control), 1:40 (V/f Control), 1:10 (PM Open Loop
Range Vector Control)
Control Speed Control
0.2% in Open Loop Vector Control <1>
Characteristics Accuracy
5 Hz (20 °C ±10 °C) in Open Loop Vector Control

Specifications
Speed Response (excludes temperature fluctuation when performing Rotational Auto-
Tuning)
Torque Limit Open Loop Vector Control only. Adjustable in 4 quadrants.
Accel/Decel Time 0.00 to 6000.0 s (allows four separate settings for accel and decel)
Instananeous Average Decel Torque <2>: 0.1/0.2 kW: over 150%, 0.4/0.75
kW: over 100%, 1.5 kW: over 50%, 2.2 kW and above: over 20%
Braking Torque Continuous Regen Torque: 20%, A
125% with a Braking Resistor Unit <3>: (10% ED) 10 s with an internal
braking resistor.
V/f Characteristics Preset V/f patterns and user-set program available.
Momentary Power Loss Ride-Thru, Speed Search, Overtroque Detection,
Torque Limit, Multi-Step Speed (17 steps max), Accel/Decel Time Switch,
S-Curve Accel/Decel, 3-Wire Sequence, Rotational Auto-Tuning, Stationary
Auto-Tuning of Line-to-Line Resistance, Dwell, Cooling Fan ON/OFF, Slip
Motor Protection
Compensation, Torque Compensation, Frequency Jump, Frequency
Reference Upper/Lower Limit, DC Injection Braking (start and stop), High
Slip Braking, PID Control (with Slip Function), Energy Saving,
MEMOBUS (RS-485/422 Max 115.2 kbps), Fault Reset, Parameter Copy.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 299
A.4 Drive Specifications

Item Specification
Motor Protection
Motor overheat protection via output current sensor
Momentary
Overcurrent
Drives stops when output exceeds 200% of the rated current (Heavy Duty)
Protection
A stop command will be entered after operating at 150% for 60 s (Heavy
Overload Protection
Duty) <4>
Drive stops when DC bus voltage falls below the levels indicated: <5>
Low Voltage
190 V (3-phase 200 V), 160 V (single-phase 200 V), 380 V (3-phase 400 V),
Protection
350 V (3-phase 380 V)
Momentary Power 3 selections available: Ridethru disabled (stops after 15 ms), time base of 0.5
Loss Ride-Thru s, and continue running until power is restored. <6>
Protection Heatsink Overheat
Protected by thermistor
Functions Protection
Braking Resistor
Overheat sensor for braking resistor (Optional ERF-type, 3%ED)
Overheat Protection
Stall prevention is available during acceleration, deceleration, and during
Stall Prevention run. Separate settings for each type of stall prevention determine the current
level at which stall prevention is triggered.
Cooling Fan Failure
Circuit protection (“fan-lock” sensor)
Protection
Electronic circuit protection (triggered by the same levels as momentary
Ground Protection
current protection) <7>
DC Bus Charge
Remains lit until DC bus voltage falls below 50 V
LED
Storage/Installation
Indoors
Area
Ambient -10 to +40 °C (wall-mounted enclosure)
Temperature -10 to +50 °C (open chassis)
Humidity 95 RH% or less with no condensation
Storage Temperature -20 to +60 °C allowed for short-term transport of the product
Altitude 1000 m or less
10 to 20 Hz: 9.8 m/S 2
Shock, Impact
Environment 20 to 55 Hz: 5.9 m/S 2
• Install the drive in an area free from:
• oil mist and dust
• metal shavings, oil, water or other foriegn materials
• radioactive materials
Surrounding Area • combustible materials
• harmful gases and liquids
• excessive vibration
• chlorides
• direct sunlight
Orientation Install the drive vertically to maintain maximum cooling effects

300 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 A.4 Drive Specifications

Item Specification
Safety Regulations and Standards UL508C, EN954-1 Cat.3
Open chassis (IP20)
Protective Enclosure
Wall-mounted enclosure (NEMA Type 1): available as an option
CIMR-VB0001 to 0006: self-cooled
CIMR-VAB0010 to 0012: cooling fan
CIMR-VA20001 to 0004: self-cooled
Cooling Method
CIMR-VA20006 to 0069: cooling fan
CIMR-VA40001 to 0004: self-cooled
CIMR-VA40005 to 0038: cooling fan

<1> Speed control accuracy varies somewhat according to the type of motor and drive settings. Contact Yaskawa
for more information.
<2> Instantaneous average deceleration torque refers to the torque required to decelerate the motor (uncoupled from
the load) from 60 Hz in the shortest time.
<3> Ensure that Stall Prevention Selection during Deceleration is disabled (L3-04 = 0) or set to 3 when using a
braking resistor or the Braking Resistor Unit. The default setting for the stall prevention function will interfere
with the braking resistor.
<4> Overload protection may be triggered when operating with 150% of the rated output current if the output
frequency is less than 6 Hz.
<5> Parameter settings allow up to 150 V.
<6> A Momentary Power Loss Ridethru Unit is required for 200/400V class drives 7.5 kW and less if the
application needs to continue running during a momentary power loss up to 2 seconds.
<7> Ground protection cannot be provided under the following circumstances when a ground fault is likely in the
motor windings during run: Low ground resistance for the motor cable and terminal block; low ground
resistance for the motor cable and terminal block; or the drive is powered up from a ground short.

Specifications
A

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 301
A.5 Drive Watts Loss Data

A.5 Drive Watts Loss Data

Table A.6 Watts Loss 200 V Class Single-Phase Models

Model
Rated Heatsink Interior Unit Total Loss
Drive Duty Fc (kHz) Number
Amps (A) Loss (W) Loss (W) (W)
CIMR-V
BA0001 0.8 28.7 15.5 44.2
BA0002 1.6 38.8 21.9 60.7
BA0003 3.0 52.0 29.5 81.5
8 BA0006 5.0 80.6 43.9 124.5
BA0010 8.0 4.7 12.5 17.2
BA0012 11.0 7.2 13.7 20.9
BA0020 17.5 14.0 18.6 32.6
HD
BA0001 0.8 3.0 7.1 10.1
BA0002 1.6 6.0 8.4 14.4
BA0003 3.0 12.6 10.6 23.2
2 BA0006 5.0 28.7 15.5 44.2
BA0010 8.0 38.8 21.9 60.7
BA0012 11.0 52.0 29.5 81.5
BA0020 17.5 80.6 43.9 124.5
BA0001 1.2 4.7 12.5 17.2
BA0002 1.9 7.2 13.7 20.9
BA0003 3.2 14.0 18.6 32.6
ND 2
BA0006 6.0 35.6 25.6 61.2
BA0010 9.6 48.6 34.5 83.1
BA0012 12.0 57.9 42.6 100.5

302 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 A.5 Drive Watts Loss Data

Table A.7 Watts Loss 200 V Class Three-Phase Models

Interior
Model Number Rated Heatsink Total
Drive Duty Fc (kHz) CIMR-V Amps (A) Loss (W)
Unit Loss
Loss (W)
(W)
2A0001 0.8 4.3 7.3 11.6
2A0002 1.6 7.9 8.8 16.7
2A0004 3.0 16.1 11.6 27.7
8 2A0006 5.0 27.4 15.9 43.3
2A0010 8.0 54.8 23.8 78.6
2A0012 11.0 70.7 29.9 100.6
2A0020 17.5 110.5 43.3 153.8
HD
2A0001 0.8 3.0 7.0 10.0
2A0002 1.6 6.0 8.3 14.3
2A0004 3.0 12.6 10.6 23.2
2 2A0006 5.0 21.1 14.3 35.4
2A0010 8.0 38.8 19.8 58.6
2A0012 11.0 52.0 25.3 77.3
2A0020 17.5 80.6 35.8 116.4
2A0001 1.2 4.7 11.9 16.6
2A0002 1.9 7.2 13.5 20.7

Specifications
2A0004 3.5 15.1 17.7 32.8
ND 2 2A0006 6.0 26.2 21.4 47.6
2A0010 9.6 48.6 30.5 79.1
2A0012 12.0 57.9 35.9 93.8
2A0020 19.6 93.3 53.0 146.3
A

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 303
A.5 Drive Watts Loss Data

Table A.8 Watts Loss 400 V Class Three-Phase Models

Rated Interior
Model Number Heatsink Total
Drive Duty Fc (kHz) CIMR-V
Amps
Loss (W)
Unit Loss
Loss (W)
(A) (W)
4A0001 1.2 19.2 11.5 30.7
4A0002 1.8 28.9 14.8 43.7
4A0004 3.4 42.3 17.9 60.2
8 4A0005 4.8 70.7 26.2 96.9
4A0007 5.5 81.0 30.7 111.7
4A0009 7.2 84.6 32.9 117.5
4A0011 9.2 107.2 41.5 148.7
HD
4A0001 1.2 8.2 8.6 16.8
4A0002 1.8 13.0 10.9 23.9
4A0004 3.4 21.3 12.6 33.9
2 4A0005 4.8 32.8 16.8 49.6
4A0007 5.5 38.2 20.0 58.2
4A0009 7.2 44.3 22.8 67.1
4A0011 9.2 57.6 29.1 86.7
4A0001 1.2 8.2 14.4 22.6
4A0002 2.1 15.5 18.4 33.9
4A0004 4.1 26.4 21.2 47.6
ND 2 4A0005 5.4 37.5 25.7 63.2
4A0007 6.9 49.7 32.4 82.1
4A0009 8.8 55.7 36.0 91.7
4A0011 11.1 71.9 51.7 123.6

304 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 A.6 Drive Derating Data

A.6 Drive Derating Data

The drive can be operated at above rated temperature, altitude and default carrier frequency
by derating the drive capacity. For example, a 10 amp continuous rated drive may be
operated at higher temperatures if it is only used to supply 8 amps continuous.

◆ Carrier Frequency Derating

As the carrier frequency of the drive is increased above the factory setting the drive capacity
should be derated according to Figure A.1.
Figure A.1

Drive
Rating Carrier Frequency Derating

0&

*&
200 V Class:
80% of HD
400 V Class
60% of HD

Specifications
   
Carrier(C6-02)

Figure A.1 Carrier Frequency Derating

◆ Temperature Derating
As the ambient temperature for the drive is increased above the drive specification the drive A
should be derated. Additionally parameter L8-35 Side-by-Side Selection on page 305 should
be set according to enclosure type and mounting method as illustrated in Figure A.2
Ambient Temperature and Installation Method Derating on page 306.
■ Output Current Derating Due to Ambient Temperature
If the ambient temperature is above the drive specification or if drives are side-by-side
mounted in a cabinet, the parameters L8-12 and L8-35 must be set according to the
installation conditions. The output current is derated as shown in Figure A.2.

No. Name Description Range Def.

Ambient Adjust the drive overload (OL2) protection level
L8-12 Temperature when the drive is installed in an environment that 40 to 60 40 °C
Setting exceeds its ambient temperature rating.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 305
A.6 Drive Derating Data

No. Name Description Range Def.

0: Disabled (standard installation)
Side-by-Side 1: Side-by-Side installation
L8-35 0 to 3 0
Selection 2: IP20/NEMA Type 1
3: Finless/Fin Outside installation
Figure A.2

Parameter L8-35 = 0 (IP20)

 Parameter L8-35 = 2
(IP20/NEMA Type 1)


Drive 
Rating Parameter L8-35 = 3
(Finless/ Fin outside installation)


Parameter L8-35 = 1
(Side-by-side installation)

Ambient temp oC

 Parameter L8-12
o o o o
  
Figure A.2 Ambient Temperature and Installation Method Derating

◆ Altitude Derating
Yaskawa recommends referencing two standards when considering altitude derating. These
standards are:
• ANSI/IEEE C 37.40: Service Conditions and Definitions for High Voltage Fuses,
Distributor Enclosed Single Pole Air Switches and Accessories
• IEC 282-1.2: High Voltage Fuse
■ Drive Derating
Power conversion equipment must be de-rated above a certain altitude (usually 1000
meters). Equipment that depends on air for its insulating and cooling medium has a higher
temperature rise and a lower dielectric strength value when operated at altitudes higher than
1000 meters (3300 feet). Application of the correct de-rating factors is necessary to prevent
drive failure.
The effect of high altitudes may eventually result in thermal damage to the power semi-
conductors and related components (reduced effectiveness of the heat sinks) as well as lower
dielectric withstand capabilities. High altitude de-rating is, therefore, an important
consideration during the initial application of the drive. Figure A.3 is provided as a quick
reference to aid in derating the drive above specified altitude.
Note: This derate applies only to the inverter. However, if the inverter is placed in a pressurized cabinet
so that the internal pressure is maintained at the value of atmospheric pressure at 3300ft. then
there is no need for derate. Example: Heatsink is exposed to the outside and is not under

306 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 A.6 Drive Derating Data

positive pressure in an enclosed cabinet with forced air cooling or an air-conditioning system. In
such a case, derating is required.
Figure A.3

Figure A.3 Altitude Derating for Yaskawa Drives

■ Motor Derating

Specifications
Consult the motor manufacturer for the applicable altitude de-rating factor before applying
the motor. As a general guideline, consult the NEMA standard MG 1-14.04 (Operation of
AC and DC Fractional- and Integral-HP Motors and Generators at Altitudes Above 3,300
feet (1000 meters). However, the motor manufacturer's specific de-rating data is always
preferable.
A

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 307
A.6 Drive Derating Data

308 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 B
Parameter List
This chapter contains a full listing of all parameters and settings
available in the drive

B.1 PARAMETER GROUPS . . . . . . . . . . . . . . . . . . . . . . . . . 310

B.2 PARAMETER TABLE . . . . . . . . . . . . . . . . . . . . . . . . . . . 311

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 309
B.1 Parameter Groups

B.1 Parameter Groups

Parameter Parameter
Name Page Name Page
Group Group
A1 Initialization 311 H4 Analog Outputs 349
A2 User Parameters 312 H5 Serial Communications Setup 350
b1 Sequence 313 H6 Pulse Train I/O Setup 351
b2 DC Injection Braking 314 L1 Motor Overload 352
b3 Speed Search 315 L2 Power Loss Ride-Thru 353
b4 Delay Timer 316 L3 Stall Prevention 355
b5 PID Control 316 L4 Reference Detection 358
b6 Dwell Function 319 L5 Fault Restart 359
b8 Energy Saving 319 L6 Overtorque Detection 360
C1 Acceleration/Deceleration Time 320 L7 Torque Limit 363
C2 S-Curve Accel/Decel 321 L8 Hardware Protection 363
C3 Motor Slip Compensation 321 n1 Hunting Prevention 366
C4 Motor Torque Compensation 322 n2 Speed Feedback Protection 367
C5 Speed Control (ASR) 323 n3 High-Slip Braking 367
Motor Line-to-Line Resistance
C6 Carrier Frequency 323 n6 368
Online Tuning
d1 Frequency Reference 325 n8 PM Motor Control 368
d2 Reference Limits 326 o1 Monitor Display Selection 370
d3 Jump Frequencies 327 o2 Operator Keypad Functions 371
d4 Frequency Reference Hold 327 o4 Maintenance Functions 372
d7 Off-Set Frequency 329 q DriveWorksEZ Parameters 373
E1 V/f Pattern 330 r DriveWorksEZ Connection 373
E2 Motor Setup 331 T1 Auto-Tuning 375
E3 Motor 2 V/f Pattern 332 U1 Status Monitor 376
E4 Motor Setup 2 333 U2 Fault Trace 380
E5 PM Motor Setup 335 U3 Fault History 381
Fault Detection during PG Speed
F1 336 U4 Maintenance Monitor 383
Control
F6 Network Communications 338 U5 Application Monitor 386
F7 Network Communications 338
H1 Digital Inputs 341 U6 Control Monitor 386
Custom Monitors for
H2 Digital Outputs 344 U8 387
DriveWorksEZ
H3 Analog Inputs 348

310 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 B.2 Parameter Table

B.2 Parameter Table

◆ A: Initialization Parameters
The A parameter group creates the operating environment for the drive. This includes the
parameter Access Level, Motor Control Method, Password, User Parameters and more.

Control
Mode
No. Name Description Range Def. O Addr. Pg.
V/ P Hex
L
f V M

A1: Initialization Parameters

Use A1 parameters to configure the basic environment for drive operation.
Selects which parameters are accessible via the
digital operator.
A1-01
Access Level 0: Operation only
<22> 0 to 2 2 A A A 101H —
Selection 1: User Parameters (access to a set of parameters
<16>
selected by the user)
2: Advanced Access Level
Selects the Control Method of the drive.
0: V/f Control without PG
Control Method 2: Open Loop Vector (OLV)
A1-02 0, 2, 5 0 S S S 102 122
Selection 5: PM Open Loop Vector (PM)Note: Does not
return to the default setting when the drive is
initialized.

Parameter List
Resets all parameters to factory default settings. 0 to
0 A A A 103 —
(Initializes the drive then returns A1-03 to 0) 3330
0: No Initialize
Initialize 1110: User Initialize (First set user parameter The following parameters are not
A1-03 reset when the performing
Parameters values must be stored using parameter o2-03)
2220: 2-Wire Initialization initialization:
3330: 3-Wire Initialization A1-00, A1-02, A1-07, and all U2
and U3 monitors.
B
5550: OPE04 Error Reset
0 to
A1-04 Password 1 0 A A A 104 —
9999
0 to
0 A A A 105 —
When the value set into A1-04 does not match the 9999
value set into A1-05, parameters A1-01 thru A1- This parameter is hidden from
03, A1-06, and A2-01 thru A2-32 cannot be view. To access A1-05, first
A1-05 Password 2 changed. display A1-04. Then press the
—
STOP key while holding down
the up arrow key. Parameter
A1-05 will appear.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 311
B.2 Parameter Table

Control
Mode
No. Name Description Range Def. Addr. Pg.
V/ O P Hex
f L M
V
Sets parameters that are commonly used in certain
applications to A2-01 through A2-16 for easier
access.
0: General-purpose (A2 parameters are not
affected)
Application 1: Water supply pump
A1-06 0 to 7 0 A A A 127 —
Preset 2: Conveyor
3: Exhaust fan
4: HVAC fan
5: Air compressor
6: Crane (Hoist)
7: Crane (Travelling)
0: Disabled
DriveWorksEZ
1: Enabled
A1-07 Function 0 to 2 0 A A A —
2: Multi-function input (enabled when H1- =
Selection
9F)
A2: User Parameters
Use A2 parameters to program the drive.
Parameters that were recently edited are listed here.
A2-01 The user can also select parameters to appear here
User Parameters, b1-01 to -- 106 to
to for quick access. A A A —
1 to 32 o2-08 <16> 125
A2-32 Parameters will be stored here for quick access
when A1-01 = 1.
0: Parameters A2-01 through A2-32 are reserved
User Parameter for the user to create a list of User Parameters.
1
A2-33 Automatic 1: Save history of recently viewed parameters. 0,1 A A A 126 —
<4>
Selection Recently edited parameters will be saved to A2-17
through A2-32 for quick access.

<4> Default setting value is dependent on parameter A1-06. This setting value is 0 when A1-06 = 0, and 1 when A1-06
does not = 0.
<16> Default setting value is dependent on parameter A1-06, Application Selection.
<22> Parameter can be changed during run.

◆ b: Application
Application parameters configure the Run Command Source, DC Injection Braking, Speed
Search, Timer functions, PID control, the Dwell function, Energy Savings and a variety of
other application-related settings.

312 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 B.2 Parameter Table

Control
Mode
No. Name Description Range Def. O Addr. Pg.
V/ L P Hex
f M
V
b1: Operation Mode Selection
Use b1 parameters to configure the operation mode.
Selects the frequency reference input source.
0: Operator - Digital preset speed d1-01 to d1-
17.
Frequency Reference
b1-01 1: Terminals - Analog input terminal A1 or A2. 0 to 4 1 S S S 180 124
Selection 1
2: Memobus communications
3: Option PCB
4: Pulse Input (Terminal RP)
Selects the run command input source.
0: Operator - RUN and STOP keys on the
Run Command digital operator.
b1-02 0 to 3 1 S S S 181 127
Selection 1 1: Digital input terminals S1 to S7
2: Memobus communications
3: Option PCB.
Selects the stopping method when the run 0 to 3 0 S S S 182 129
command is removed.
0: Ramp to Stop
Stopping Method DC Injection Braking at Stop
b1-03 1: Coast to Stop
Selection cannot be selected when using
2: DC Injection Braking to Stop
3: Coast with Timer (A new run command is Open Loop Vector for PM motors.
ignored if received before the timer expires)

Parameter List
Permits or prohibits reverse operation.
Reverse Operation
b1-04 0: Reverse enabled. 0,1 0 A A A 183 —
Selection
1: Reverse disabled.
Determines the operation when the Run
command source is switched from LOCAL to
REMOTE or between Run source 1 and 2

b1-07
Local/Remote Run
Selection
while an external Run command is active at the
new source. 0,1 0 A A A 186 — B
0: External Run command has to be cycled at
the new source to be activated.
1: External Run command at new source is
accepted immediately.
0: Run command accepted only in the
Run Command operation menu.
b1-08 Selection while in 1: Run command accepted in all menus. 0 to 2 0 A A A 187 —
Programming Mode 2: Prohibit entering programming mode during
Run

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 313
B.2 Parameter Table

Control
Mode
No. Name Description Range Def. Addr. Pg.
V/ O P Hex
f L M
V
Sets the phase order for drive output terminals
U/T1, V/T2 and W/T3.
b1-14 Phase Order Selection 0,1 0 A A A 1C3 —
0: Standard
1: Switch phase order
Selects the frequency reference input source.
0: Operator - Digital preset speed d1-01 to d1-
17.
Frequency
b1-15 1: Terminals - Analog input terminal A1 or A2 0 to 4 0 A A A 1C4 —
Reference 2
2: Memobus communications
3: Option PCB
4: Pulse Input (Terminal RP)
Selects the run command input source.
0: Operator - RUN and STOP keys on the
Run Command digital operator.
b1-16 0 to 3 0 A A A 1C5 —
Source 2 1: Digital input terminals S1 to S7
2: Memobus communications
3: Option PCB
Determines the operation when a Run
Run Command at command is active at power up of the drive.
b1-17 0,1 0 A A A 1C6 —
Power Up 0: Run command not issued, needs to be cycled
1: Run command issued, motor operation start
b2: DC Injection Braking
Use b2 parameters to configure DC Injection Braking operation
Sets the frequency at which DC Injection
DC Injection Braking Braking starts when Ramp to Stop (b1-03 = 0) 0.0 to 0.5
b2-01 A A A 189 —
Start Frequency is selected. If b2-01< E1-09, DC Injection 10.0 Hz
Braking starts at E1-09.
DC Injection Braking Sets the DC Injection Braking current as a
b2-02 0 to 75 50% A A − 18A —
Current percentage of the drive rated current.
DC Injection Braking 0.00
Sets DC Injection Braking time at start. 0.00 to
b2-03 Time/DC Excitation s A A − 18B —
Disabled when set to 0.00 seconds. 10.00
Time at Start <1>
Sets DC Injection Braking time at stop.When
b1-03 = 2, actual DC Injection time is
calculated as follows:
(b2-04) x 10 x (Output Freq) / (E1-04).
DC Injection Braking 0.00 to 0.50
b2-04 When b1-03 = 0, this parameter sets the A A − 18C —
Time at Stop 10.00 s
amount of DC Injection time applied to the
motor at the end of the decel ramp or High Slip
Braking.
Disabled when set to 0.00.

314 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 B.2 Parameter Table

Control
Mode
No. Name Description Range Def. Addr. Pg.
V/ O P Hex
f L M
V
Magnetic Flux Sets the magnetic flux compensation as a
0 to
b2-08 Compensation percentage of the no-load current value 0% − A − 190 —
1000
Capacity (E2-03).
Short Circuit Brake Sets the time for Short-Circuit Brake operation 0.00 to 0.00
b2-12 − − A 1BA —
Time at Start at start. Disabled when set to 0.00. <32> 25.50 s
Sets Short-Circuit Brake operation time at
Short Circuit Brake stop. Used to stop a motor rotating due to 0.00 to 0.50
b2-13 − − A 1BB —
Time at Stop inertia. Disabled when set to 0.00 seconds. 25.50 s
<32>
b3: Speed Search
Use B3 parameters to configure Speed Search function operation.
Enables/disables speed search function at start.
0: Disabled - Speed Search is not automatically
Speed Search
b3-01 performed at start. 0 to 1 0 A A A 191 —
Selection
1: Enabled - Speed Search is automatically
performed at start.
Sets the current level at which the speed is
Speed Search 120
b3-02 assumed to be detected and Speed Search is 0 to 200 A A − 192 —
Deactivation Current <2>
ended. Set in percent of the drive rated current.
Sets the time constant used to reduce the
Speed Search 0.1 to
b3-03 output frequency during speed search. Related 2.0 s A A − 193 —
Deceleration Time 10.0
to a change from max. output frequency to 0.

Parameter List
Delays the speed search operation after a
Speed Search Delay 0.0 to
b3-05 momentary power loss to allow time for an 0.2 s A A A 195 —
Time 100
external output contactor to close.
Sets the current injected to the motor at the
Output Current 1 0.0 to <12
b3-06 beginning of Esitmation type Speed Search. A A − 196 —
during Speed Search 2.0 >
Set as a factor to the motor rated current.

Speed Search
Sets the gain which is applied to the speed
detected by Speed Estimation Speed Search
B
1.00 to
b3-10 Detection before the motor is reaccelerated.Increase this 1.05 A A − 19A —
1.20
Compensation Gain setting if OV occurs when performing speed
search.
Selects if Speed Search detects the motor
rotation direction during speed search.
Bi-Directional Speed
b3-14 0: Disabled–Frequency reference direction 0,1 0 A A − 19E —
Search Selection
used
1: Enabled–Detected direction used
Speed Search Restart Sets the speed search restart current level in 150
b3-17 0 to 200 A A − 1F0 —
Current Level percentag of the drive rated current. %

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 315
B.2 Parameter Table

Control
Mode
No. Name Description Range Def. Addr. Pg.
V/ O P Hex
f L M
V
Speed Search Restart Sets the time in seconds for speed search 0.00 to 0.10
b3-18 A A − 1F1 —
Detection Time restart to be detected. 1.00 s
Number of Speed Sets the number of restarts possible for speed
b3-19 0 to 10 3 A A − 1F2 —
Search Restarts search restart operations.
Sets the Speed Search detection mode.
Speed Search Method
b3-24 0: Current Detection Type 0,1 0 A A − 1C0 —
Selection
1: Speed Estimation Type
Speed Search Retry 0 to
b3-25 Sets the wait time before Speed Search restarts. 0.5 s A A A 1C8 —
Interval Time 30.0
b4: Timer Function
Use b4 parameters to configure timer function operation.
Used in conjunction with a multi-function
digital input (H1- = 18) and a multi-
Timer Function function digital output (H2- = 12) 0.0 to
b4-01 0.0 s A A A 1A3 —
On-Delay Time programmed for the timer function. This sets 300.0
the amount of time between digital input
closure and digital output activation.
Used in conjunction with a multi-function
digital input (H1- = 18) and a multi-
Timer Function function digital output programmed for the 0.0 to
b4-02 0.0 s A A A 1A4 —
Off-Delay Time timer function. This sets the amount of time the 300.0
output remains activated after the digital input
is opened.
b5: PID Control
Use b5 parameters to configure the PID control drive function.
Sets the PID control mode.
0: Disabled
1: Enable (Deviation is D-controlled)
2: Enable (Feedback is D-controlled)
b5-01 PID Function Setting 0 to 4 0 A A A 1A5 —
3: Enable (Deviation is D-controlled, PID
outut added to Freq. Ref.)
4: Enable (Feedback is D-controlled, PID outut
added to Freq. Ref.)
b5-02 Proportional Gain Sets the proportional gain of the PID 0.00 to
1.00 A A A 1A6 —
<22> Setting (P) controller. A setting of 0.00 disables P control. 25.00
b5-03 Integral Time Setting Sets the integral time for the PID controller. A 0.0 to
1.0 s A A A 1A7 —
<22> (I) setting of 0.0 s disables integral control. 360.0
b5-04 Sets the maximum output possible from the 0.0 to 100.
Integral Limit Setting A A A 1A8 —
<22> integrator. 100.0 0%
b5-05 Sets D control derivative time. A setting of 0.00 to 0.00
Derivative Time (D) A A A 1A9 —
<22> 0.00 s disables derivative control. 10.00 s

316 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 B.2 Parameter Table

Control
Mode
No. Name Description Range Def. Addr. Pg.
V/ O P Hex
f L M
V
b5-06 Sets the maximum output possible from the 0.0 to 100.
PID Output Limit A A A 1AA —
<22> entire PID controller. 100.0 0%
-100.0
b5-07 PID Offset 0.0
Applies an offset to the PID controller output. to A A A 1AB —
<22> Adjustment %
+100.0
b5-08 PID Primary Delay Sets the amount of time for the filter on the 0.00 to 0.00
A A A 1AC —
<22> Time Constant output of the PID controller. 10.00 s
Sets the PID controller output direction.
PID Output Level
b5-09 0: Normal Output (direct acting) 0,1 0 A A A 1AD —
Selection
1: Reverse Output (reverse acting)
PID Output Gain 0.00 to
b5-10 Sets the gain applied to the PID output. 1.00 A A A 1AE —
Setting 25.00
Sets the drive operation with negative PID
output.
0: Drive stops with negative PID output
PID Output Reverse
b5-11 1: Rotation direction reverses with negative 0,1 0 A A A 1AF —
Selection
PID output.
When using setting 1 make sure, reverse
operation is permitted by parameter b1-04.
Configures the PID feedback loss detection.
0: Disabled.
1: Feedback loss detected when PID enabled.
Alarm output, operation is continued without

Parameter List
triggering a fault contact.
2: Feedback loss detected when PID enabled.
Fault output, operation is stopped and a fault
contact is triggered.
PID Feedback
3: Feedback loss detection even when PID is
b5-12 Reference Missing 0 to 5 0 A A A 1B0 —
disabled by digital input. No alarm/fault
Detection Selection
output. “PID feedback loss” digital output is
switched,
B
4: PID Feedback error detection even when
PID is disabled by digital input. An alarm is
triggered and the drive continues to run.
5: PID Feedback error detection even when
PID is disabled by digital input. Fault is
triggered and output is shut off.
PID Feedback Loss
b5-13 Sets the PID feedback loss detection level. 0 to 100 0% A A A 1B1 —
Detection Level
PID Feedback Loss Sets the PID feedback loss detection delay time 0.0 to
b5-14 1.0 s A A A 1B2 —
Detection Time in terms of seconds. 25.5

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 317
B.2 Parameter Table

Control
Mode
No. Name Description Range Def. Addr. Pg.
V/ O P Hex
f L M
V
PID Sleep Function Sets the sleep function start frequency. 0.0 to 0.0
b5-15 A A A 1B3 —
Start Level Note: Also enabled when PID is not active. 400.0 Hz
PID Sleep Delay Sets the sleep function delay time in units of 0.0 to
b5-16 0.0 s A A A 1B4 —
Time 0.1 seconds. 25.5
PID Accel/Decel Applies an accel/decel time to the PID setpoint 0 to
b5-17 0 s A A A 1B5 —
Time reference. 255
Selects b5-19 as PID setpoint value.
PID Setpoint
b5-18 0: Disabled 0,1 0 A A A 1DC —
Selection
1: Enabled, b5-19 becomes PID target
0.00 to 0.00
b5-19 PID Setpoint Value Sets the PID target value when b5-18 = 1. A A A 1DD —
100.00 %
Sets the units for b5-19, and for parameter
monitors U5-01 (PID Feedback) and U5-04
(PID Setpoint).
b5-20 PID Setpoint Scaling 0: 0.01Hz units 0 to 3 1 A A A 1E2 —
1: 0.01% units (100% = max output frequency)
2: r/min (motor pole number must be set up)
3: User-set (set to b5-38 and b5-39)
-100.0
b5-34 PID Output Lower Sets the minimum output possible from the 0.00
to A A A 19F —
<22> Limit PID controller. %
+100.0
b5-35 Limits the PID control input (deviation signal). 0 to 1000
PID Input Limit A A A 1A0 —
<22> Acts as a bipolar limit. 1000.0 .0%
PID Feedback High 100
b5-36 Sets the PID feedback high detection level. 0 to 100 A A A 1A1 —
Detection Level %
PID Feedback High Sets the PID feedback high level detection 0.0 to
b5-37 1.0 s A A A 1A2 —
Level Detection Time delay time. 25.5
0 to 60000: User-Set Display if b5-20=3
PID Setpoint / User 1 to
b5-38 Set the numbers displayed by designating the <5> A A A 1FE —
Display 60000
maximum PID target.
Sets the number of digits the PID setpoint.
0: No decimal places
PID Setpoint Display
b5-39 1: One decimal places 0 to 3 <5> A A A 1FF —
Digits
2: Two decimal places
3: Three decimal places

318 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 B.2 Parameter Table

Control
Mode
No. Name Description Range Def. Addr. Pg.
V/ O P Hex
f L M
V
b6: Dwell Function
Use b6 parameters to configure dwell function operation.
Dwell Reference at The Dwell function is used to temporarily hold 0.0 to 0.0
b6-01 A A A 1B6 —
Start the frequency when driving a motor with a 400.0 Hz
heavy load. 0.0 to
b6-02 Dwell Time at Start Parameters b6-01 and b6-02 set the frequency 0.0 s A A A 1B7 —
10.0
to hold and the time to maintain that frequency
Dwell Frequency at at start. 0.0 to 0.0
b6-03 A A A 1B8 —
Stop Parameters b6-03 and b6-04 set the frequency 400.0 Hz
to hold and the time to maintain that frequency
at stop.
Output
Frequency

Run command
10 0.0 to
b6-04 Dwell Time at Stop 0.0 s A A A 1B9 —
10.0

Time

b8: Energy Saving

Use b8 parameters to configure the energy saving/conservation drive function.
Selects the Energy Savings function.
Energy Saving
b8-01 0: Disabled 0,1 0 A A − 1CC —
Control Selection

Parameter List
1: Enabled (set b8-04)
b8-02 Sets energy savings control gain when in Open 0.0 to
Energy Saving Gain 0.7 − A − 1CD —
<22> Loop Vector (OLV) control mode. 10.0
Energy Saving
b8-03 Sets energy saving control filter time constant 0.00 to
Control Filter Time 0.50 − A − 1CE —
<22> when in Open Loop Vector control. 10.00
Constant

b8-04
Energy Saving Sets the Energy Saving coefficient and is used 0.0 to <57
A − − 1CF —
B
Coefficient Value to fine adjustments in V/f Control. 655.00 >
Power Detection Sets a filter time for the Power Detection used 0 to 20
b8-05 A − − 1D0 —
Filter Time by Energy Savings in V/f Control. 2000 ms
Sets the limit for the voltage search operation
Search Operation performed by Energy Savings in V/f Control.
b8-06 0 to 100 0% A − − 1D1 —
Voltage Limit Set as a percentage of the motor base voltage.
Disabled when set to 0%.

<1> Default setting value is dependent on parameter A1-02, Control Method Selection. The value shown is for A1-02
= 2-OLV control.
<2> Default setting value is dependent on parameter A1-02, Control Method Selection. The value shown is for A1-02
= 0-V/f Control.
<5> Default setting is dependent on parameter b5-20, PID Setpoint Scaling.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 319
B.2 Parameter Table

<12> Default setting value is dependent on parameter o2-04, Drive/kVA Selection.

<14> Default setting value is dependent on parameter o2-09, Initialization Spec. Selection.
<22> Parameter can be changed during run.
<32> A coasting motor may require a braking resistor circuit to bring the motor to a stop in the required time.
<33> Increase the setting value in increments of 0.1 when estimating the minimum output frequency for a motor
coasting at high speed while attempting Speed-Estimation Type Speed Search.
<34> Increase this value if an OV overvoltage fault occurs when performing Speed Search at start.
<57> Default setting value is dependent on parameter o2-04, Drive/kVA Selection and C6-01, Drive Duty Selection.

◆ C: Tuning
C parameters are used to adjust the acceleration and deceleration times, S-curves, slip- and
torque compensation functions and carrier frequency selections.

Control
Mode
No. Name Description Range Def. Addr. Pg.
V/ O P Hex
L
f M
V
C1: Acceleration and Deceleration Times
Use C1 parameters to configure motor acceleration and deceleration.
0.0 to
C1-01 Sets the time to accelerate from 0 to
Acceleration Time 1 6000.0 10.0 s S S S 200 132
<22> maximum frequency.
<6>
0.0 to
C1-02 Sets the time to decelerate from maximum
Deceleration Time 1 6000.0 10.0 s S S S 201 132
<22> frequency to 0.
<6>
Sets the time to accelerate from 0 to 0.0 to
C1-03
Acceleration Time 2 maximum frequency when Accel/Decel 6000.0 10.0 s A A A 202 —
<22>
times 2 are selected by a digital input. <6>
Sets the time to decelerate from maximum 0.0 to
C1-04
Deceleration Time 2 frequency to 0 when Accel/Decel times 2 are 6000.0 10.0 s A A A 203 —
<22>
selected by a digital input. <6>
Acceleration Time 3 Sets the time to accelerate from 0 to 0.0 to
C1-05
(Motor 2 Accel maximum frequency when Accel/Decel 6000.0 10.0 s A A A 204 —
<22>
Time 1) times 3 are selected by a digital input. <6>
Deceleration Time 3 Sets the time to decelerate from maximum 0.0 to
C1-06
(Motor 2 Decel frequency to 0 when Accel/Decel times 3 are 6000.0 10.0 s A A A 205 —
<22>
Time 1) selected by a digital input. <6>
Acceleration Time 4 Sets the time to accelerate from 0 to 0.0 to
C1-07
(Motor 2 Accel maximum frequency when Accel/Decel 6000.0 10.0 s A A A 206 —
<22>
Time 2) times 4 are selected by a digital input. <6>
Deceleration Time 4 Sets the time to decelerate from maximum 0.0 to
C1-08 (Motor 2 Decel frequency to 0 when Accel/Decel times 4 are 6000.0 10.0 s A A A 207 —
Time 2) selected by a digital input. <6>

320 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 B.2 Parameter Table

Control
Mode
No. Name Description Range Def. Addr. Pg.
V/ O P Hex
f L M
V
Sets the time to decelerate from maximum
frequency to 0 for the multi-function input 0.0 to
C1-09 Fast-Stop Time fast-stop function. Note: This parameter is 6000.0 10.0 s A A A 208 —
also used by selecting “Fast-Stop” as a Stop <6>
Method when a fault is detected.
Sets the resolution of C1-01 to C1-09.
Accel/Decel Time
C1-10 0: 0.01 s (0.00 to 600.00 s) 0,1 1 A A A 209 —
Setting Units
1: 0.1 s (0.0 to 6000.0 s)
Sets the frequency for automatic
acceleration/deceleration switching.
Accel/Decel Time Below set frequency: Accel/Decel Time 4 0.0 to 0.0
C1-11 A A A 20A —
Switching Frequency Above set frequency: Accel/Decel Time 1 400.0 Hz Hz
The multi-function input “Accel/Decel Time
1” or “Accel/Decel Time 2” take priority.
C2: S-Curve Characteristics
Use C2 parameters to configure S-curve operation.
S-Curve
The S-curve can be controlled in the four 0.00 to 0.20 s
C2-01 Characteristic at A A A 20B —
points shown below. S-curve is used to 10.00 <2>
Accel Start
run
S-Curve command ON OFF
0.00 to
C2-02 Characteristic at output
0.20 s A A A 20C —
10.0
Accel End frequency C2-02 C2-03

S-Curve

Parameter List
C2-01 C2-04
0.00 to
C2-03 Characteristic at 0.20 s A A A 20D —
10.0
Decel Start time
further soften the starting and stopping ramp.
S-Curve
The longer the S-curve time, the softer the 0.00 to
C2-04 Characteristic at 0.00 s A A A 20E —
starting and stopping ramp. 10.0
Decel End
C3: Slip Compensation
Use C3 parameters to configure the slip compensation function. B
Sets the slip compensation gain. Decides for
C3-01 Slip Compensation what amount the output frequency is boosted 0.0
0.0 to 2.5 A A − 20F —
<22> Gain in order to compensate the slip. <2>
Note: Adjustment is not normally required.
Adjusts the slip compensation function delay
time. Decrease the setting when the slip
2000
Slip Compensation compensation response is too slow, increase 0 to
C3-02 ms A A − 210 —
Primary Delay Time it when the speed is not stable. 10000
<2>
Disabled when Simple V/f Control with PG
(H6-01 = 3) is used.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 321
B.2 Parameter Table

Control
Mode
No. Name Description Range Def. Addr. Pg.
V/ O P Hex
f L M
V
Sets the slip compensation upper limit. Set as
Slip Compensation a percentage of motor rated slip (E2-02).
C3-03 0 to 250 200% A A − 211 —
Limit Disabled when Simple V/f Control with PG
(H6-01 = 3) is used.
Selects slip compensation during
regenerative operation.
Slip Compensation 0: Disabled
C3-04 Selection during 1: EnabledUsing the Slip Compensation 0,1 0 A A − 212 —
Regeneration function during regeneration may require a
braking option to handle momentary
increasing regenerative energy.
Selects if the motor magnetic flux is reduced
Output Voltage Limit during output voltage saturation. 0
C3-05 0,1 − A − 213 —
Operation Selection 0: Disabled <2>
1: Enabled
C4: Torque Compensation
Use C4 parameters to configure Torque Compensation function.
V/f control: Sets the gain for the automatic
torque (voltage) boost function and helps to
produce better starting torque.
Increase this setting when using a long motor
cable or when the motor is significantly
smaller than the drive capacity.
C4-01 Torque Compensation 0.00 to
Decrease this setting when motor oscillation 1.00 A A A 215 —
<23> Gain 2.50
occurs. Set the value so that the current at
low speed does not exceeds the drives rated
current.
Open Loop Vector: Sets the torque
compensation function gain. Normally no
change is required.
Sets the torque compensation filter time.
Increase this setting when motor oscillation 200
Torque Compensation 0 to
C4-02 occurs. ms A A A 216 —
Primary Delay Time 60000
Reduce the setting if there is not enough <1>
response from the motor.
Torque Compensation Sets torque compensation at forward start as 0.0 to
C4-03 0.0% − A − 217 —
at Forward Start a percentage of motor torque. 200.0
Torque Compensation Sets torque compensation at reverse start as a -200.0 to
C4-04 0.0% − A − 218 —
at Reverse Start percentage of motor torque. 0.0

322 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 B.2 Parameter Table

Control
Mode
No. Name Description Range Def. Addr. Pg.
V/ O P Hex
f L M
V
Sets the time constant for torque
Torque Compensation compensation at forward start and reverse 0 to 10
C4-05 – A – 219 —
Time Constant start (C4-03 and C4-04). The filter is 200 ms
disabled if the time is set to 4 ms or less.
Sets the torque compensation time 2. When
an OV fault occurs with sudden load changes
or at the and of an acceleration, increase the
Torque Compensation 0 to 150
C4-06 setting. – A – 21AH —
Primary Delay Time 2 10000 ms
Note: Adjustment is not normally required. If
adjusted then AFR time 2 (n2-03) should be
adjusted too.
C5: Speed Control (ASR)
Use C5 parameters to configure the Automatic Speed Regulator (ASR).
C5 parameters are available only when using V/f with Simple PG (H6-01 = 3).
C5-01 ASR Proportional Sets the proportional gain of the speed 0.00 to
0.20 A 21B —
<22> Gain 1 control loop (ASR). 300.00
– –
C5-02 Sets the integral time of the speed control 0.000 to
ASR Integral Time 1 0.200 A 21C —
<22> loop (ASR). 10.000
C5-03 ASR Proportional Sets the speed control gain 2 of the speed 0.00 to
0.02 A − − 21D —
<22> Gain 2 control loop (ASR). 300.00
C5-04 Sets the integral time 2 of the speed control 0.000 to 0.050
ASR Integral Time 2 A 21E —
<22> loop (ASR). 10.000 s

Parameter List
Sets the upper limit for the speed control – –
C5-05 0.0 to
ASR Limit loop (ASR) as a percentage of the maximum 5.0% A 21F —
<22> 20.0
output frequency (E1-04).
C6: Carrier Frequency
Use C6 parameters to configure the carrier frequency drive settings.
Selects the load rating for the drive.
0: Heavy Duty (HD) for constant torque
applications.
B
Normal/Heavy Duty
C6-01 1: Normal Duty (ND) for variable torque 0,1 1 S S S 223 134
Selection
applications.
This setting affects the Rated output current
and overload tolerance of the drive.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 323
B.2 Parameter Table

Control
Mode
No. Name Description Range Def. Addr. Pg.
V/ O P Hex
f L M
V
Selects the carrier frequency
1: 2.0 kHz
2: 5.0 kHz
3: 8.0 kHz
4: 10.0 kHz
5: 12.5 kHz
Carrier Frequency 6: 15.0 kHz
C6-02 1 to F <3> S S S 224 135
Selection 7: Swing PWM1 (Audible sound 1)
8: Swing PWM2 (Audible sound 2)
9: Swing PWM3 (Audible sound 3)
A: Swing PWM4 (Audible sound 4)
B to E: No setting possible
F: User defined (determined by C6-03
through C6-05)
Carrier Frequency Open Loop Vector: C6-03 defines the fixed 1.0 to
C6-03 <8> A A A 225 —
Upper Limit carrier frequency if C6-02 = F. 15.0
V/f control: C6-03 and C6-04 set upper and
lower limits for the carrier frequency.

carrier frequency

C6-03

C6-04 output frequency

× (C6-05) × K
Carrier Frequency output 0.4 to
C6-04 frequency <8> A - - 226 —
Lower Limit E1-04 15.0
max output
frequency
The coefficient K depends on C6-03:
C6-03 ≥ 10.0 kHz: K = 3
10.0 kHz > C6-03 ≥ 5.0 kHz: K = 2
5.0 kHz > C6-03: K = 1
When C6-05 ≤ 6, C6-04 is disabled (makes
the carrier frequency C6-03 value).
Carrier Frequency Sets the relationship of output frequency to
C6-05 00 to 99 <8> A - - 227 —
Proportional Gain carrier frequency when C6-02 = F.

<1> Default setting value is dependent on parameter A1-02, Control Method Selection. The value shown is for A1-02 =
2-OLV control.
<2> Default setting value is dependent on parameter A1-02, Control Method Selection. The value shown is for A1-02 =
0-V/f Control.
<3> Default setting value is dependent on parameters o2-04, Drive/kVA Selection, A1-02, Control Method Selection
and C6-01, Normal/Heavy Duty selection. 351.
<6> Setting range value is dependent on parameter C1-10, Accel/Decel Time Setting Units. When C1-10 = 0 (units of
0.01 seconds), the setting range becomes 0.00 to 600.00 seconds.
<8> Default setting value is dependent on parameter C6-02, Carrier Frequency Selection.

324 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 B.2 Parameter Table

<22> Parameter can be changed during run.

<23> Parameter cannot be changed during run when parameter A1-02 = 5-PM OLV Control.

◆ d: References
Reference parameters are used to set the various frequency reference values during
operation.

Control
Mode
No. Name Description Range Def. O Addr. Pg.
V/ L P Hex
f V M

d1: Frequency Reference

Use d1 parameters to configure the drive frequency reference.
d1-01 Frequency 0.00
Frequency reference S S S 280 124
<22> Reference 1 Hz
d1-02 Frequency Frequency reference when digital input "Multi- 0.00
S S S 281 124
<22> Reference 2 Step Speed Reference 1" (H1- = 3) is on. Hz
d1-03 Frequency Frequency reference when digital input "Multi- 0.00
S S S 282 124
<22> Reference 3 Step Speed Reference 2” (H1- = 4) is on. Hz
Frequency reference when digital inputs "Multi-
d1-04 Frequency 0.00
Step Speed Reference 1, 2" (H1- = 3 and 4) S S S 283 124
<22> Reference 4 Hz
are on.
d1-05 Frequency Frequency reference when digital input "Multi- 0.00
A A A 284 —
<22> Reference 5 Step Speed Reference 3" (H1- = 5) is on. Hz
0.00 to

Parameter List
Frequency reference when digital inputs "Multi- 400.00
d1-06 Frequency 0.00
Step Speed Reference 1, 3 " (H1- = 3 and 5) Hz A A A 285 —
<22> Reference 6 Hz
are on. <11>
Frequency reference when digital inputs "Multi- <19>
d1-07 Frequency 0.00
Step Speed Reference 2, 3" (H1- = 4 and 5) A A A 286 —
<22> Reference 7 Hz
are on.

d1-08 Frequency
Frequency reference when multi-function input
0.00
B
"Multi-Step speed reference 1, 2, 3" (H1- = A A A 287 —
<22> Reference 8 Hz
3, 4, 5) are on.
Frequency reference when multi-function input
d1-09 Frequency 0.00
"Multi-Step Speed Reference 4" (H1- = 32) A A A 288 —
<22> Reference 9 Hz
is on.
Frequency reference when digital input "Multi-
d1-10 Frequency 0.00
Step Speed Reference 1, 4" (H1- = 3 and 32) A A A 28B —
<22> Reference 10 Hz
are on.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 325
B.2 Parameter Table

Control
Mode
No. Name Description Range Def. Addr. Pg.
V/ O P Hex
f L M
V
Frequency reference when digital inputs "Multi-
d1-11 Frequency 0.00
Step Speed Reference 2, 4" (H1- = 4 and 32) A A A 28C —
<22> Reference 11 Hz
are on.
Frequency reference when digital inputs "Multi-
d1-13 Frequency 0.00
Step Speed Reference 3, 4" (H1- = 5 and 32) A A A 28E —
<22> Reference 13 Hz
are on.
Frequency reference when digital inputs "Multi-
d1-14 Frequency 0.00
Step Speed Reference 1, 3, 4" (H1- = 3, 5, A A A 28F —
<22> Reference 14 Hz
32) are on.
Frequency reference when digital inputs "Multi- 0.00 to
d1-15 Frequency 0.00
Step Speed Reference 2, 3, 4" (H1- = 4, 5, 400.00 A A A 290 —
<22> Reference 15 Hz
32) are on. Hz
<11>
Frequency reference when digital inputs "Multi-
d1-16 Frequency <19> 0.00
Step Speed Reference 1, 2, 3, 4" (H1- = 3, 4, A A A 291 —
<22> Reference 16 Hz
5, 32) are on.
Frequency reference when digital inputs "Jog
Frequency Reference", "Forward Jog" or
d1-17 Jog Frequency 6.00
"Reverse Jog." are on. "Jog Frequency S S S 292 124
<22> Reference Hz
Reference" has priority over "Multi-Step Speed
Reference 1 to 16”.
d2: Frequency Upper and Lower Limits
Use d2 parameters to configure the frequency reference limits.
Sets the frequency reference upper limit as a
Frequency percentage of maximum output frequency (E1-
0.0 to 100.
d2-01 Reference Upper 04). Output speed is limited to this value even if A A A 289 —
110.0 0%
Limit the frequency reference is higher. This limit
applies to all frequency reference sources.
Sets the frequency reference lower limit as a
Frequency percentage of maximum output frequency (E1-
0.0 to 0.0
d2-02 Reference Lower 04). Output speed is limitedto this value even if A A A 28A —
110.0 %
Limit the frequency reference is lower. This limit
applies to all frequency reference sources.
Sets the minimum frequency reference lower
Master Speed limit if the frequency reference is input using an
0.0 to 0.0
d2-03 Reference Lower analog input. Set as a percentage of maximum A A A 293 —
110.0 %
Limit output frequency (E1-04). The higher of both
values d2-01 and d2-03 will be the lower limit.

326 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 B.2 Parameter Table

Control
Mode
No. Name Description Range Def. Addr. Pg.
V/ O P Hex
f L M
V
d3: Jump Frequency
Use d3 parameters to configure the drive Jump Frequency settings.
d3-01 to d3-04 allow programming of three 0.0
d3-01 Jump Frequency 1 A A A 294 —
prohibited frequency reference points for Hz
eliminating problems with resonant vibration of 0.0
d3-02 Jump Frequency 2 the motor / machine. This feature does not A A A 295 —
0.0 to Hz
eliminate the selected frequency values, but
400.0
accelerates and decelerates the motor through
the prohibited bandwidth. 0.0
d3-03 Jump Frequency 3 A A A 296 —
The parameters must be according to the rule; Hz
d3-01 ≥ d3-02 ≥ d3-03.
This parameter sets the dead-band width around
Jump Frequency each selected prohibited frequency reference 0.0 to 1.0
d3-04 A A A 297 —
Width point. The bandwidth becomes the designated 20.0 Hz
Jump frequency, plus or minus d3-04.
d4: Frequency Reference Hold
Use d4 parameters to configure the drive frequency reference hold function.
This parameter is used to hold the last frequency
reference in U1-01 (d1-01) when power is
removed.
Frequency 0: Disabled
d4-01 Reference Hold 1: Enabled 0,1 0 A A A 298 —
Function Selection This function is available when the multi-

Parameter List
function inputs “accel/decel ramp hold” or “up/
down” commands are selected
(H1-†† = A or 10 and 11).
Sets the bias added to the frequency reference
when the Up/Down 2 digital inputs are set.
When set to 0.00 Hz, the bias value is increased
d4-03
<22>
Frequency or decreased according to d4-04. 0.00 to
Reference Bias Step When greater than 0.0 Hz, the bias value d4-03 99.99
0.00
Hz
A A A 2AA — B
(Up/Down 2) is added or subtracted to/from the frequency Hz
reference.
The acceleration or deceleration rate is
ultimately determined by d4-04.
0: Adjusts the bias value according to the
Frequency
d4-04 currently selected accel/decel time.
Reference Accel/ 0,1 0 A A A 2AB —
<22> 1: Adjusts the bias value by Accel/Decel Time 4
Decel (Up/Down 2)
(C1-07 and C1-08).

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 327
B.2 Parameter Table

Control
Mode
No. Name Description Range Def. Addr. Pg.
V/ O P Hex
f L M
V
0: Holds the bias value when Up/Down 2
Frequency reference is on or off.
Reference Bias 1: When the Up 2 reference and Down 2
d4-05
Operation Mode reference are both on or both off, the applied 0,1 0 A A A 2AC —
<22>
Selection bias becomes 0. Currently selected accel/ decel.
(Up/Down 2) times are used.
Enabled only when d4-03 = 0.
100% = Max output frequency (E1-04).
Saves the bias value once the frequency
reference is adjusted.The bias can be set by the
user, but will be disabled under the following
conditions:
When none of the multi-function input terminals
are assigned +0 frequency reference bias
Frequency function.
-99.9 to 0.0
d4-06 Reference Bias When the frequency reference priority has A A A 2AD —
+100.0 %
(Up/Down 2) changed (including multi-step speed).
When both d4-03 = 0 and d4-05 = 1 while the
Up 2 / Down 2 commands are both on or both
off.
When the max output frequency has changed
(E1-04).
When the digital frequency reference has
changed.
• When the Up 2 and Down 2 commands are
enabled, the frequency reference holds the bias
value as the levels for the analog frequency
Analog Frequency
reference or pulse train frequency reference 0.1
d4-07 Reference 1.0
change, accelerating or decelerating to the to A A A 2AE —
<22> Fluctuation Limit %
frequency reference. After frequency agree is +100.0
(Up/Down 2)
achieved, the bias process starts again.
• Enabled only when the analog or pulse train
reference is on.
Frequency
When d4-06 is greater than d4-08, d4-08 0.1
d4-08 Reference Bias 0.0
becomes the bias for the upper limit. Set as a to A A A 2AF —
<22> Upper Limit (Up/ %
percentage of the max output frequency. 100.0
Down 2)
Frequency
When d4-06 is less than d4-09, d4-09 becomes
d4-09 Reference Bias -99.9 0.0
the bias for the lower limit. Set as a percentage A A A 2B0 —
<22> Lower Limit (Up/ to 0.0 %
of the max output frequency.
Down 2)

328 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 B.2 Parameter Table

Control
Mode
No. Name Description Range Def. Addr. Pg.
V/ O P Hex
f L M
V
Selects which value is used as frequency
reference lower limit if the Up/Down function is
Up/Down Frequency used.
d4-10 Reference Limit 0: The lower limit is determined by d2-02 or 0 or 1 0 A A A 2B6 —
Selection analog input (H3-02/10 = 0). The higher of both
values becomes the reference limit.
1: The lower limit is determined by d2-02.
Sets the gain used by the simple positioning stop 0.50 to
d4-12 Stop Position Gain 1.00 A A A 2B8
function to fine adjust the position. 2.55
d7: Offset Frequency
Use d7 parameters to set the offset frequency.
Added to the frequency reference when the -100.0
d7-01 0.0
Offset Frequency 1 digital input “Frequency Offset 1” to A A A 2B2 —
<22> %
(H1- = 44) is switched on. +100.0
Added to the frequency reference when the -100.0
d7-02 0.0
Offset Frequency 2 digital input “Frequency Offset 2” to A A A 2B3 —
<22> %
(H1- = 45) is switched on. +100.0
Added to the frequency reference when the -100.0
d7-03 0.0
Offset Frequency 3 digital input “Frequency Offset 3” to A A A 2B4 —
<22> %
(H1- = 46) is switched on. +100.0

<11> Default setting value is dependent on parameter o1-03, Digital Operator Display Selection.
<19> Range upper limit is dependent on parameters E1-04, Maximum Output Frequency, and d2-01, Frequency

Parameter List
Reference Upper Limit.
<22> Parameter can be changed during run.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 329
B.2 Parameter Table

◆ E: Motor Parameters
Control
Mode
No. Name Description Range Def. O Addr. Pg.
P Hex
V/f L M
V
E1: V/f Pattern Characteristics
Use E1 parameters to set V/f characteristics for the motor.
This parameter must be set to the power
supply voltage. It sets the maximum and base
voltage used by preset V/f patterns (E1-03 = 0
to E) and adjusts levels used by certain
functions. Refer to page 130 for details
E1-01 Input Voltage 155 to
WARNING! Drive input voltage (not motor 200 V S S S 300 138
<24> Setting 255
voltage) must be set in E1-01 for the
protective features of the drive to function
properly. failure to do so may result in
equipment damage and/or death or personal
injury.
Selects a preset V/f pattern.
0: 50 Hz Constant torque 1
1: 60 Hz Constant torque 2
2: 60 Hz Constant torque 3 (50Hz base)
3: 72 Hz Constant torque 4 (60 Hz base)
4: 50 Hz Variable torque 1
5: 50 Hz Variable torque 2
6: 60 Hz Variable torque 3
V/f Pattern 7: 60 Hz Variable torque 4
E1-03 0 to F F A A − 302 —
Selection 8: 50 Hz High starting torque 1
9: 50 Hz High starting torque 2
A: 60 Hz High starting torque 3
B: 60 Hz High starting torque 4
C: 90 Hz (60 Hz base)
D: 120 Hz (60 Hz base)
E: 180 Hz (60 Hz base)
F: Custom V/f. E1-04 through E1-13 settings
define the V/f pattern.

330 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 B.2 Parameter Table

Control
Mode
No. Name Description Range Def. O P Addr. Pg.
V/f L M Hex
V
40.0 to
Max Output 60 Hz
E1-04 400.0 S S S 303 139
Frequency <10>
<21>
E1-05 Max Output These parameters are only applicable when 0.0 to 230 V
E1-03 is set to F. To set linear V/f S S S 304 139
<24> Voltage 255.0 <10>
characteristics, set the same values for E1-07
Base 0.0 to 60 Hz
E1-06 and E1-09. In this case, the setting for E1-08 S S S 305 139
Frequency E1-04 <10>
will be disregarded. Ensure that the four
Mid Output frequencies are set according to these rules: 0.0 to 3.0 Hz
E1-07 A A A 306 —
Frequency E1-04 <2>
Mid Output E1-04 ≥ E1-06> E1-07 ≥ E1-09 18.4 V
E1-08 0.0 to
Frequency VACrms Out(V) <2> A A A 307 —
<24> 255.0
Voltage E1-05
<12>
E1-12 1.5 Hz
Minimum 0.0 to
E1-09 <2> S S S 308 139
Output Freq. E1-13 E1-04
<10>
Minimum 13.8 V
E1-10 0.0 to
Output Freq. <2> A A A 309 —
<24> E1-08 255.0
Voltage <12>
E1-11 Mid Output 0.0 to
0.0 Hz A A A 30A —
<26> Frequency 2 E1-10 E1-04
E1-12 Mid Output E1-09 E1-07 E1-06 E1-11 E1-04 0.0 to
<24> Frequency Frequency (Hz) 0.0 V A A A 30B —

Parameter List
255.0
<26> Voltage 2
E1-13 0.0 to
Base Voltage 0.0 V A S S 30C —
<24> 255.0
E2: Motor Parameters
Use E2 parameters to set motor-related data.
10 to
200% of
B
Sets the motor nameplate full load current in
Motor Rated drive
E2-01 amperes (A). Automatically set during <57> S S − 30E 398
Current rated
Auto-Tuning.
current
<27>
Sets the motor rated slip in Hertz (Hz).
Motor Rated 0.00 to
E2-02 Automatically set during rotational <57> A A − 30F —
Slip 20.00
Auto-Tuning.
Sets the magnetizing current of the motor as a
Motor 0 to less
percentage of the motor rated current (E2-01).
E2-03 No-Load than <57> A A − 310 —
Automatically set during rotational
Current E2-01
Auto-Tuning.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 331
B.2 Parameter Table

Control
Mode
No. Name Description Range Def. O P Addr. Pg.
V/f L M Hex
V
Number of Sets the number of motor poles.
E2-04 2 to 48 4 poles A A − 311 —
Motor Poles Automatically set during Auto-Tuning.
Motor 0.000 to
Sets the phase-to-phase motor resistance in
E2-05 Line-to-Line 65.000 <57> A A − 312 —
ohms. Automatically set during Auto-Tuning.
Resistance <37>
Sets the voltage drop due to motor leakage
Motor
inductance as a percentage of motor rated 0.0 to
E2-06 Leakage <57> A A − 313 —
voltage. Automatically set during 40.0
Inductance
Auto-Tuning.
Motor
Sets the motor iron saturation coefficient at
Iron-Core E2-07 to
E2-07 75% of magnetic flux. Automatically set 0.50 − A − 314 —
Saturation 0.50
during Auto-Tuning.
Coefficient 1
Motor
Sets the motor iron saturation coefficient at
Iron-Core [E2-07]
E2-08 75% of magnetic flux. Automatically set 0.75 − A − 315 —
Saturation to 0.75
during during Auto-Tuning.
Coefficient 2
Sets the motor mechanical loss as a
percentage of motor rated power (kW).
Motor
Adjust in the following circumstances: 0.0 to
E2-09 Mechanical 0.0% − A − 316 —
When there is a large amount of torque loss 10.0
Loss
due to motor bearing friction.
When there is a large amount of torque loss.
Motor Iron
Loss for 0 to
E2-10 Sets the motor iron loss in watts (W). <57> A − − 317 —
Torque 65535
Compensation
Sets the motor rated power in kilowatts (kW). 0.40
Motor Rated 0.00 to
E2-11 Automatically set during Auto-Tuning. kW S S − 318 399
Output 650.00
(1HP = 0.746 kW). <12>
Motor Set to the motor iron saturation coefficient at
Iron-Core 130% of magnetic flux. 1.30 to
E2-12 1.30 − A − 328 —
Saturation Automatically set during rotational 5.00
Coefficient 3 Auto-Tuning.
E3: Motor 2 V/f Characteristics
Use E3 parameters to set the V/f pattern for a second motor.
Motor 2
0: V/f Control
E3-01 Control 0 or 2 0 A A − 319 —
2: Open Loop Vector (OLV)
Method

332 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 B.2 Parameter Table

Control
Mode
No. Name Description Range Def. O P Addr. Pg.
V/f L M Hex
V
Motor 2 Max
40.0 to
E3-04 Output 60 Hz A A − 31A —
400.0
Frequency
E3-05 Motor 2 Max 0.0 to
These parameters set the V/f pattern for motor 230 V A A − 31B —
<24> Voltage 255.0
2.
Motor 2 Base 0.0 to
E3-06 To set linear V/f characteristics, set the same 60 Hz A A − 31C —
Frequency E3-04
values for E3-07 and E3-09. In this case, the
Motor 2 Mid setting for E3-08 will be disregarded. Ensure 0.0 to 3.0 Hz
E3-07 A A − 31D —
Output Freq. that the four frequencies are set according to E3-04 <53>
Motor 2 Mid these rules or OPE10 fault will occur: 18.4 V
E3-08 E3-04 ≥ E3-06 > E3-07 > E3-09 0.0 to
Output Freq. <12> A A − 31E —
<24> 255.0
Voltage VACrms Out (V) <53>
Motor 2 Min. E3-05 0.0 to 1.5 Hz
E3-09 E3-12
A A − 31F —
Output Freq. E3-04 <53>
Motor 2 Min. E3-13 13.8 V
E3-10 0.0 to
Output Freq. <12> A A − 320 —
<24> 255.0
Voltage <53>
Motor 2 Mid E3-08
E3-11 0.0 to
Output 0.0 Hz A A − 345 —
<26> E3-04
Frequency 2
E3-10
Motor 2 Mid
E3-12 0.0 to
Output E3-09 E3-07 E3-06 E3-11 E3-04 0.0

Parameter List
<24> 255.0 A A − 346 —
Frequency Frequency (Hz) Vac
<52> <24>
Voltage 2
0.0 to
E3-13 Motor 2 Base 0.0
255.0 A S − 347 —
<24> Voltage Vac
<24>
E4: Motor 2 Parameters
Use E4 parameters to control a second motor operating on the same drive. B
10 to
Sets the motor 2 name plate full load current 200% of
Motor 2 Rated
E4-01 in amperes (A). This value is automatically drive <57> A A − 321 —
Current
set during Auto-Tuning. rated
current
Sets the motor 2 name plate full load current
Motor 2 Rated 0.00 to
E4-02 in amperes (A). Automatically set during <57> A A − 322 —
Slip 20.00
Auto-Tuning.
Sets the magnetizing current of motor 2 in 0 to less
Motor 2 Rated
percentage of full load current (E4-01). than
E4-03 No-Load <57> A A − 323 —
Automatically set during Rotational [E4-01]
Current
Auto-Tuning. <27>

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 333
B.2 Parameter Table

Control
Mode
No. Name Description Range Def. O P Addr. Pg.
V/f L M Hex
V
Sets the number of poles of motor 2. This
Motor 2 Motor
E4-04 value is automatically set during 2 to 48 4 poles A A − 324 —
Poles
Auto-Tuning.
Motor 2 0.000 to
Sets the phase-to-phase resistance of motor 2
E4-05 Line-to-Line 65.000 <57> A A − 325 —
in ohms. Automatically during Auto-Tuning.
Resistance <37>
Sets the voltage drop due to motor leakage
Motor 2
inductance as a percentage of rated voltage of 0.0 to
E4-06 Leakage <57> A A − 326 —
motor 2. Automatically set during 40.0
Inductance
Auto-Tuning.
Motor 2 Motor
Set to the motor iron saturation coefficient at
Iron-Core 0.00 to
E4-07 50% of magnetic flux. Automatically set 0.50 − A − 343 —
Saturation 0.50
during Rotational Auto-Tuning.
Coefficient 1
Motor 2 Motor Set to the motor iron saturation coefficient at Setting
Iron-Core 75% of magnetic flux. This value is for
E4-08 0.75 − A − 344 —
Saturation automatically set during Rotational E4-07 to
Coefficient 2 Auto-Tuning. 0.75
Sets the motor mechanical loss as a
percentage of motor rated power (kW)
Motor 2 capacity.
0.00 to
E4-09 Mechanical Adjust in the following circumstances: 0.0 − A − 33F —
10.0
Loss When there is a large amount of torque loss
due to motor bearing friction.
When there is a large amount of torque loss.
Motor 2 Iron 0 to
E4-10 Sets the motor iron loss in watts. <57> − A − 340 —
Loss 65535
Motor 2 Rated Sets the motor rated capacity in kW. 0.00 to
E4-11 <12> A A − 327 —
Capacity Automatically set during Auto-Tuning. 650.00
Motor 2
Set to the motor iron saturation coefficient at
Iron-Core 1.30 to
E4-12 130% of magnetic flux. Automatically set 1.30 − A − 342 —
Saturation 5.00
during Rotational Auto-Tuning.
Coefficient 3
Motor 2 Slip Sets the slip compensation gain for motor 2.
E4-14 0.0
Compensation The function is the same as C3-01 for motor 0.0 to 2.5 A A − 341 —
<22> <53>
Gain 1. Refer to the C3-01 description.
Torque Sets the torque compensation gain for motor
1.00 to
E4-15 Compensation 2. The function is the same as C4-01 for 1.00 A A − 341 —
2.50
Gain - Motor 2 motor 1. Refer to the C4-01 description.

334 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 B.2 Parameter Table

Control
Mode
No. Name Description Range Def. O P Addr. Pg.
V/f L M Hex
V
E5: PM Motor Parameters
Enter the Yaskawa motor code for the PM
motor being used. Various motor parameters
are automatically set based on the value of
this parameter.
Note: Set to FFFF when using a specialized
or custom motor. For all other motors:

0000
Motor voltage
class and
capacity
Motor Code
E5-01 0: Pico motor 0: 1800 r/min 0000 to <12> <
Selection (for − − S 329 398
<25> (SMRA series) series FFFF 38>
PM motor)
1: Derated torque 1: 3600 r/min
IPM motor series
(SSR1 series) 2: 1750 r/min
2: Constant torque series
IPM motor 3: 1450 r/min
(SST4 series) series
4: 1150 r/min
series
F: Custom motor
All motor parameters are re-initialized to
factory settings when this parameter is set.

Parameter List
Motor Rated
E5-02 0.10 to
Capacity (for Sets the rated capacity of the motor. <10> − − S 32A 401
<25> 18.5
PM motor)
10 to
200% of
Motor Rated drive
E5-03 Sets the motor rated current in amps. <4> − − S 32B 401
Current rated
current B
<27>
E5-04
Motor Poles Sets the number of motor poles. 2 to 48 <10> − − S 32C 401
<25>
E5-05 Motor Set the resistance for each motor phase in 0.000 to
<10> − − S 32D 401
<25> Resistance units of 0.001 Ω. 65.000
E5-06 Motor d Axis Sets the d axis inductance in units of 0.00 to
<10> − − S 32E 401
<25> Inductance 0.01 mH. 300.00
E5-07 Motor q Axis Sets the q axis inductance in units of 0.00 to
<10> − − S 32F 401
<25> Inductance 0.01 mH. 600.00

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 335
B.2 Parameter Table

Control
Mode
No. Name Description Range Def. O P Addr. Pg.
V/f L M Hex
V
Set the induced phase peak voltage in units of
0.1 mV (rad/min) [electrical angle].
Set this parameter when using a Yaskawa
Motor SSR1 series PM motor with derate torque, or
E5-09 Induction a Yaskawa SST4 series motor with constant 0.0 to
<10> − − S 331 401
<25> Voltage torque. 2000.0
Constant 1 When setting this parameter, E5-24 should be
set to 0. An alarm will be triggered if both E5-
09 and E5-24 are set to 0, or if neither
parameter is set to 0.
Set the induced phase-to-phase rms voltage in
units of 0.1 mV/(r/min) [mechanical angle].
Set this parameter when using a Yaskawa
SMRA series pico motor.
Motor
When setting this parameter, E5-09 should be
E5-24 Induction 0.0 to 0
set to 0. An alarm will be triggered if both E5- − − S 353 401
<25> Voltage 2000.0 <10>
09 and E5-24 are set to 0, or if neither
Parameter 2
parameter is set to 0.
If E5-03 (Motor Rated Current) is set to 0,
however, then an alarm will not be triggered
when both E5-09 and E5-24 are set to 0.

◆ F: Options
F parameters are used to program the drive for PG feedback and to function with option
cards.

Control
Mode
No. Name Description Range Def. Addr. Pg.
V/ O
L P Hex
f V M

F1: Simple PG V/f Parameters

Use F1 parameters to set up the drive for Simple PG V/f control. These parameters are enabled only when H6-01 = 03

336 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 B.2 Parameter Table

Control
Mode
No. Name Description Range Def. Addr. Pg.
V/ O P Hex
f L M
V
Sets stopping method when a PG open circuit
fault (PGO) occurs. Refer to parameter F1-14.
0: Ramp to Stop - Decelerate to stop using the
Operation Selection at
active deceleration time.
F1-02 PG Open Circuit 0 to 3 1 A − − 381 —
1: Coast to Stop
(PGO)
2: Fast-stop - Decelerate to stop using the
deceleration time in C1-09.
3: Alarm only - Drive continues operation.
Sets the stopping method when an overspeed
(OS) fault occurs. Refer to F1-08 and F1-09.
0: Ramp to stop - Decelerate to stop using the
Operation Selection at active deceleration time.
F1-03 0 to 3 1 A − − 382 —
Overspeed (OS) 1: Coast to stop
2: Fast - Stop - Decelerate to stop using the
deceleration time in C1-09.
3: Alarm Only - Drive continues operation.
Sets the stopping method when a speed
deviation (DEV) fault occurs. Refer to F1-10
and F1-11.
0: Ramp to stop - Decelerate to stop using the
Operation Selection at
F1-04 active deceleration time. 0 to 3 3 A − − 383 —
Deviation
1: Coast to stop
2: Fast-stop - Decelerate to stop using the
deceleration time in C1-09.

Parameter List
3: Alarm only - Drive continues operation.
Sets the speed feedback level which has to be
exceeded for the time set in F1-09 before an
Overspeed Detection 115
F1-08 OS fault will occur. 0 to 120 A − − 387 —
Level %
Set as a percentage of the maximum output
frequency (E1-04).

F1-09
Overspeed Detection
Sets the time in seconds for which the speed
feedback has to exceed the overspeed detection
0.0 to
1.0 A − − 388 —
B
Delay Time 2.0
level F1-08 before an OS fault will occur.
Sets the allowable deviation between motor
Excessive Speed speed and frequency reference before a speed
F1-10 Deviation Detection deviation fault (DEV) is triggered. 0 to 50 10% A − − 389 —
Level Set as a percentage of the maximum output
frequency (E1-04).
Sets the time in seconds for which a deviation
Excessive Speed
between motor speed and frequency reference 0.0 to
F1-11 Deviation Detection 0.5 s A − − 38A —
has to exceed the speed deviation detection 10.0
Delay Time
level F1-10 before a DEV fault will occur.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 337
B.2 Parameter Table

Control
Mode
No. Name Description Range Def. Addr. Pg.
V/ O P Hex
f L M
V
Sets the time for which no PG pulses must be
PG Open-Circuit 0.0 to
F1-14 detected before a PG Open (PGO) fault is 2.0 s A − − 38D —
Detection Time 10.0
triggered.
F6 and F7: Serial Communications Option Card Settings
Use F6 parameters to program the drive for serial communication.
Selects the operation after a communications
error occurred.
Communications
0: Ramp to stop using current accel/decel time
F6-01 Error operation 0 to 3 1 A A A 3A2
1: Coast to stop
Selection
2: Fast Stop using C1-09
3: Alarm only
Sets when an external fault from a comm
External fault from
option is detected.
F6-02 comm. option 0 or 1 0 A A A 3A3
0: Always detected
selection
1: Detection during Run only
Selects the operation after an external fault set
by a communications option (EF0).
External fault from
0: Ramp to stop using current accel/decel time
F6-03 comm. option 0 to 3 1 A A A 3A4
1: Coast to stop
operation selection
2: Fast Stop using C1-09
3: Alarm only
0.0 to
F6-04 Trace Sampling Rate - 2.0 s A A A 3A5
5.0
CC-Link Node Sets the node address if a CC-Link option card
F6-10 0 to 63 0 A A A 3E6
Address is installed
0: 156 Kbps
CC-Link 1: 625 Kbps
F6-11 communications 2: 2.5 Mbps 0 to 4 0 A A A 3E7
speed 3: 5 Mbps
4: 10 Mbps
Selects if a BUS fault can be automatically
F6-14 BUS Error auto reset 0 or 1 0 A A A 3BB
reset.
DeviceNet MAC
F6-20 Selects the drives MAC address for DeviceNet 0 to 63 0 A A A 3C1
Address
0: 125 kbps
Device Net
1: 250 kbps
F6-21 Communications 0 to 3 3 A A A 3C2
2: 500 kbps
Speed
3: Detect automatically
DeciveNet PCA
F6-22 I/O Polled Consuming Assembly Data Instance 0 to 255 0 A A A 3C3
setting
F6-23 DeciveNet PPA setting I/O Polled Producing Assembly Data Instance 0 to 255 0 A A A 3C4

338 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 B.2 Parameter Table

Control
Mode
No. Name Description Range Def. Addr. Pg.
V/ O P Hex
f L M
V
Selects if a fault s is detected during
DeciveNet Idle mode communication idle mode.
F6-24 0 or 1 0 A A A 3C5
fault detection 0: Disabled
1: Enabled
F6-30 Profibus node address Sets the node address for a Profibus option. 0 to 125 0 A A A 3CB
Selects the operation when a "Clear Mode"
Profibus Clear mode command is received.
F6-31 0 or 1 0 A A A 3CC
selection 0: Resets back to zero.
1: Maintains the previous value.
Profibus Map 0: PPO Type
F6-32 0 or 1 0 A A A 3CD
selections 1: Conventional
CANopen Node ID
F6-36 Sets the Node ID for a CANopen option 0 to 127 99 A A A 3D0
selection
0: Auto-adjust
1: 10kbps
2: 20 kbps
CANopen 3: 50 kbps
F6-37 Communications 4: 125 kbps 0 to 8 6 A A A 3D1
speed 5: 250 kbps
6: 500 kbps
7: 800 kbps
8: 1 Mbps
F6-40 CompoNet Node ID Sets the Node ID for a CompoNet option. 0 to 63 0 A A A 3D5

Parameter List
0: 93.75kbit/s
1: Reserved
2: 1.5Mbit/s
F6-41 CompoNet Speed 0 to 255 0 A A A 3D6
3: 3Mbit/s
4: 4Mbit/s
5-255: Reserved
F7-01 Ethernet IP Address 1 0 to 255 0 A A A 3E5 B
F7-02 Ethernet IP Address 1 Combining these parameters like F7-01.F7- 0 to 255 0 A A A 3E6
02.F7-03.F7-04 sets the Ethernet IP address.
F7-03 Ethernet IP Address 1 Example: (192.168.1.10) 0 to 255 0 A A A 3E7
F7-04 Ethernet IP Address 1 0 to 255 0 A A A 3E8
F7-05 Subnet Mask 1 0 to 255 0 A A A 3E9
F7-06 Subnet Mask 2 Combining these parameters like F7-05.F7- 0 to 255 0 A A A 3EA
06.F7-07.F7-08 sets the Ethernet Subnet
F7-07 Subnet Mask 3 Mask.Example: (255.255.255.0) 0 to 255 0 A A A 3EB
F7-08 Subnet Mask 4 0 to 255 0 A A A 3EC

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 339
B.2 Parameter Table

Control
Mode
No. Name Description Range Def. Addr. Pg.
V/ O P Hex
f L M
V
F7-09 Gateway Address 1 0 to 255 0 A A A 3ED
F7-10 Gateway Address 2 Combining these parameters like F7-09.F7- 0 to 255 0 A A A 3EE
10.F7-11.F7-12 sets the Ethernet Gateway
F7-11 Gateway Address 3 Address.Example: (192.168.1.1) 0 to 255 0 A A A 3EF
F7-12 Gateway Address 4 0 to 255 0 A A A 3F0
Selects how the Ethernet IP address is set.
0:User defined
F7-13 Dress Mode at Startup 0 to 2 0 A A A 3F1
1:BOOTP
2:DHCP
Sets the password required for setup changes
via the network. 0 to
F7-14 Security password 0 A A A 3F2
0: No password required 9999
1 - 9999: 4 digit password
0:Auto Negotiate
Duplex Mode
F7-15 1:Half Duplex forced 0 to 2 0 A A A 3F3
Selection
2:Full Duplex forced
0:Auto Negotiate
Communication Speed 0, 10,
F7-18 10:10 Mbps speed setting 0 A A A 3F6
Selection 100
100:100Mbps Speed Setting
Selects the mode for modification on the
Ethernet option board Web page settings
F7-19 Web Page Access 0: All access 0 to 2 0 A A A 3F7
1: Only during stop
2: Never
0: Gateway not used
F7-20 Gateway selection 0 or 1 1 A A A 3F8
1: Use Gateway
Communication loss Multiplier for communication loss detection
F7-21 0 to 300 0 A A A 3F9
time out timeout value.

◆ H Parameters: Multi-Function Terminals

H parameters assign functions to the multi-function input and output terminals.

340 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 B.2 Parameter Table

Control
Mode
No. Name Description Range Def. O Addr. Pg.
V/ L P Hex
f M
V
H1: Multi-Function Digital Input
H1 parameters to assign functions to the multi-function digital input terminals. Unused terminals should be set to "F".
Multi-Function Digital Input Terminal
H1-01 40 A A A 438 —
S1 Function Selection
Multi-Function Digital Input Terminal
H1-02 41 A A A 439 —
S2 Function Selection
Multi-Function Digital Input Terminal Selects the function of
H1-03 24 A A A 400 —
S3 Function Selection terminals S1 to S7
Multi-Function Digital Input Terminal Refer to “Multi-Function 1 to 9F
H1-04 14 A A A 401 —
S4 Function Selection Digital Input Selection <40>
Multi-Function Digital Input Terminal Table” for a description of 3(0)
H1-05 setting values. A A A 402 —
S5 Function Selection <18>
Multi-Function Digital Input Terminal 4(3)
H1-06 A A A 403 —
S6 Function Selection <18>
Multi-Function Digital Input Terminal 6(4)
H1-07 A A A 404 —
S7 Function Selection <18>

<18> Parenthetical value is the default when parameter A1-03 = 3330 3-Wire Initialization.
<40> The availability of certain functions depends on the control method used.

Parameter List
H1 Multi-Function Digital Input Selections
Control
H1- Mode
Function Description Pg.
Setting V/ O P
f LV M
Closed: Reverse rotation (only if the drive is set up for 3-
0 3-Wire Sequence
wire sequence)
O O O —
B
Open: Remote, Reference 1 or 2 (b1-01/02 or b1-15/16)
1 Local/Remote Selection O O O —
Closed: Local, LED operator is run and reference source
Open: Run and frequency reference source 1 (b1-01/02)
2 External Reference 1/2 O O O —
Closed: Run and frequency reference source 2 (b1-15/16)
3 Multi-Step Speed Reference 1 O O O —
4 Multi-Step Speed Reference 2 Used to select Multi-Step Speeds set in d1-01 to d1-16 O O O —
5 Multi-Step Speed Reference 3 O O O —
Open: Selected speed reference
6 Jog Reference Selection Closed: Jog Frequency reference (d1-17). Jog has O O O —
priority over all other reference sources.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 341
B.2 Parameter Table

H1 Multi-Function Digital Input Selections

Control
H1- Mode
Setting Function Description Pg.
V/ O P
f LV M
7 Accel/Decel Time 1 Used to switch between Accel/Decel. Time 1/2 O O O —
Open: Normal operation
8 Baseblock Command (N.O.) O O O —
Closed: No drive output
Open: No drive output
9 Baseblock Command (N.C.) O O O —
Closed: Normal operation
Closed: The drive pauses during acceleration or
A Accel/Decel Ramp Hold O O O —
deceleration and maintains the output frequency.
B Drive Overheat Alarm (OH2) Closed: Displays an OH2 alarm O O O —
Open: Terminal A2 disabled
C Terminal A2 Enable O O O —
Closed: Terminal A2 enabled
Select this setting when not using the terminal or when
F Not used O O O —
using the terminal in a pass-through mode.
10 Up Command Open: Maintains the current frequency reference O O O —
Closed: Increases or decreases the current frequency
reference. Ensure that the increase and decrease
11 Down Command commands are set in conjunction with one another. The O O O —
frequency reference source must be set to operator (b1-
01 = 0).
12 Forward Jog Closed: Runs forward at the Jog Frequency d1-17. O O O —
13 Reverse Jog Closed: Runs reverse at the Jog Frequency d1-17. O O O —
Closed: Resets faults if the cause is cleared and the Run
14 Fault Reset O O O —
command is removed.
Closed: Decelerates at the Fast-Stop time C1-09.
15 Fast-Stop (N.O.) To restart the Fast-Stop input must be released and Run O O O —
must be cycled.
Open: Motor 1 (E1- , E2- )
16 Motor 2 Selection O O O —
Closed: Motor 2 (E3- , E4- )
17 Fast-stop (N.C.) Open: Decelerates according to C1-09 (Fast-stop Time) O O O —
Set the timer delay using parameters b4-01 and b4-02.
18 Timer Input Function Ensure this function is set in conjunction with the multi- O O O —
function output timer (H2-†† = 12).
19 PID Disable Closed: PID control disabled O O O —
1A Accel/Decel Time Selection 2 Switches Accel/Decel times. O O O —
Open: Parameters can not be edited. (except U1-01 if
1B Program Lockout reference source is set for operator) O O O —
Closed: Parameters may be edited and saved.
Closed: Samples the analog frequency reference and
1E Reference Sample Hold O O O —
operates the drive at that speed.

342 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 B.2 Parameter Table

H1 Multi-Function Digital Input Selections

Control
H1- Mode
Setting Function Description Pg.
V/ O P
f LV M
20: N.O., Always Detected, Ramp To Stop
21: N.C., Always Detected, Ramp To Stop
22: N.O., During Run, Ramp To Stop
23: N.C., During Run, Ramp To Stop
24: N.O., Always Detected, Coast To Stop
25: N.C., Always Detected, Coast To Stop
26: N.O., During Run, Coast To Stop
27: N.C., During Run, Coast To Stop
20 to 28: N.O., Always Detected, Fast-stop
External Fault O O O —
2F 29: N.C., Always Detected, Fast-stop
2A: N.O., During Run, Fast-stop
2B: N.C., During Run, Fast-stop
2C: N.O., Always Detected, Alarm Only (continue
running)
2D: N.C., Always Detected, Alarm Only (continue
running)
2E: N.O., During Run, Alarm Only (continue running)
2F: N.C., During Run, Alarm Only (continue running)
30 PID Integral Reset Closed: Resets the PID control integral value. O O O —
31 PID Integral Hold Closed: Maintains the current PID control integral value. O O O —
32 Multi-Step Speed Reference 4 Used to select Multi-Step Speeds set in d1-01 to d1-16 O O O —
34 PID Soft Starter Closed: Disables the PID soft starter b5-17. O O O —

Parameter List
35 PID Input Switch Closed: Inverses the PID input signal O O O —
Open: Stop
Forward Run Command
40 Closed: Forward run Note: Can not be set together with O O O —
(2-wire sequence)
Settings 42 or 43.
Open: Stop
Reverse Run Command
41 Closed: Reverse run Note: Can not be set together with O O O —
(2-wire sequence)
Settings 42 or 43.
Open: Stop
B
Run Command (2-wire
42 Closed: Run Note: Can not be set together with Settings O O O —
sequence 2)
40 or 41.
Open: Reverse
FWD/REV Command (2-wire
43 Closed: Forward Note: Can not be set together with O O O —
sequence 2)
Settings 40 or 41.
44 Offset Frequency 1 Addition Closed: Adds d7-01 to the frequency reference. O O O —
45 Offset Frequency 2 Addition Closed: Adds d7-02 to the frequency reference. O O O —
46 Offset Frequency 3 Addition Closed: Adds d7-03 to the frequency reference. O O O —
DC Injection Braking
60 Closed: Triggers DC Injection Braking (b2-02) O O - —
Command

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 343
B.2 Parameter Table

H1 Multi-Function Digital Input Selections

Control
H1- Mode
Setting Function Description Pg.
V/ O P
f LV M
Closed: Activates Current Detection Speed Search from
61 External Search Command 1 the max. output frequency (E1-04) if b3-01=0. Activates O O O —
Speed Estimation Type Speed search if b3-01 =1.
Closed: Activates Current Detection Speed Search from
62 External Search Command 2 the frequency reference b3-01=0. Activates Speed O O O —
Estimation Type Speed search if b3-01 =1.
Open: KEB Ride-Thru 1 enabled
65 KEB Ride-Thru 1 (N.C.) O O O —
Closed: Normal operation
Open: Normal operation
66 KEB Ride-Thru 1 (N.O.) O O O —
Closed: KEB Ride-Thru 1 enabled
67 Communications Test Mode Tests the MEMOBUS/Modbus RS-485/422 interface. O O O —
68 High-Slip Braking Closed: High-Slip braking is executed. Drive stops. O - - —
Open: Drive disabled. If this input is opened during run,
6A Drive Enable then the drive will stop as specified by parameter b1-03. O O O —
Closed: Ready for operation.
75 Up 2 Command Open: Maintains the current frequency reference O O O —
Closed: Increases or decreases the frequency
reference.UP 2 and Down 2 commands must be set in
76 Down 2 Command combination with each other. The frequency reference O O O —
source must be assigned to the operator (b1-01 = “0”).
Open: KEB Ride-Thru 2 enabled
7A KEB Ride-Thru 2 (N.C.) O O O —
Closed: Normal operation
Open: Normal operation
7B KEB Ride-Thru 2 (N.O.) O O O —
Closed: KEB Ride-Thru 2 enabled
7C Short-Circuit Braking (N.O.) Open: Normal operation - - O —
7D Short-Circuit Braking (N.C.) Closed: Short-Circuit Braking - - O —
7E Forward/Reverse Detection Direction of rotation detection (for Simple V/f w/PG) O - - —
Open: DWEZ enabled
9F DriveWorksEZ enable O O O —
Closed: DWEZ disabled

Control
Mode
No. Name Description Range Def. Addr. Pg.
V/ O P Hex
L M
f V

H2: Multi-Function Digital Outputs

Use H2 parameters to assign functions to the multi-function digital outputs.

344 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 B.2 Parameter Table

Control
Mode
No. Name Description Range Def. Addr. Pg.
V/ O P Hex
f L M
V
Terminal MA, MB and MC
H2-01 E A A A 40B —
Function Selection (relay)
Refer to “Multi-Function Digital
Terminal P1 Function Selection 0 to 192
H2-02 Output Selection Table” for a 0 A A A 40C —
(open-collector) <40>
description of setting values.
Terminal P2 Function Selection
H2-03 2 A A A 40D —
(open-collector)
Sets the display units for one of the
multi-function output terminals that
is assigned to output the watt hours
(H2- = 39) is the value every
200 ms. An output pulse of 200 ms
is provided for every kWh that
occurs. Intended to drive a counter,
H2-06 Watt Hour Output Unit Selection 0 to 4 0 A A A 437 —
meter or PLC for logging kWh.

0: 0.1 kWh units

1: 1 kWh units
2: 10 kWh units
3: 100 kWh units
4: 1000 kWh units

<40> The availability of certain functions depends on the control method used.

Parameter List
H2 Multi-Function Digital Output Settings
Control
Mode
H2-
Function Description Pg.
Setting V/ O
L P
f V M

0 During Run Closed: A Run command is active or voltage is output. O O O — B

1 Zero Speed Closed: Output frequency is 0. O O O —
Closed: Output frequency equals the speed reference (plus or
2 Fref/Fout Agree 1 O O O —
minus the hysteresis set to L4-02).
Closed: Output frequency and speed reference equal the value in
3 Fref/Fset Agree 1 O O O —
L4-01 (plus or minus the hysteresis of L4-02).
Frequency (FOUT) Closed: Output frequency is less than or equal to the value in
4 O O O —
Detection 1 L4-01 with hysteresis determined by L4-02.
Frequency (FOUT) Closed: Output frequency is greater than or equal to the value in
5 O O O —
Detection 2 L4-01, with hysteresis determined by L4-02.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 345
B.2 Parameter Table

H2 Multi-Function Digital Output Settings

Control
Mode
H2-
Setting Function Description O Pg.
V/ L P
f M
V
Closed: Drive Ready. The drive is powered up, not in a fault state,
6 Drive Ready O O O —
and in the Drive mode.
7 DC Bus Undervoltage Closed: DC bus voltage is below the UV trip level set in L2-05. O O O —
8 During Baseblock Closed: This is no output voltage O O O —
9 Option Reference Closed: Digital operator supplies the frequency reference. O O O —
Open: Reference 1 or 2 are active
A Local/Remote O O O —
Closed: Digital operator supplies the run command.
Torque Detection 1 Closed: Output current/torque exceeds the torque value set in
B O O O —
(N.O.) parameter L6-02 for longer than the time set in parameter L6-03.
Closed: Loss of the analog frequency reference detected. Enabled
C Loss of Reference O O O —
when L4-05 = 1.
Closed: Braking resistor or transistor is overheated or faulted out.
D Braking Resistor Fault This selection requires that braking resistor protection parameter O O O —
be set for ERF (L8-01 = “1”).
E Fault Closed: Fault occurred (other than CPF00 and CPF01). O O O —
Set this value when the terminal is not used, or when using the
F Not used O O O —
terminal in the pass-through mode.
10 Alarm Closed: An alarm is triggered. O O O —
Reset Command
11 Closed: Reset command to the drive is active. O O O —
Active
Timer output, controlled by b4-01 and b4-02. Used in conjunction
12 Timer Output O O O —
with the digital input (H1-†† = 18 “timer function”).
Closed: When drive output frequency equals the frequency
13 Fref/Fout Agree 2 O O O —
reference +/- L4-04.
Closed: When the drive output frequency is equal to the value in
14 Fref/Fset Agree 2 O O O —
L4-03 (plus or minus L4-04).
Closed: When the drive output frequency is less than or equal to
15 Frequency Detection 3 O O O —
the value in L4-03 with the hysteresis determined by L4-04.
Closed: When the output frequency is greater than or equal to the
16 Frequency Detection 4 O O O —
value in L4-03 with the hysteresis determined by L4-04.
Torque Detection 1 Open: When the output current/torque exceeds the value set in
17 O O O —
(N.C.) parameter L6-02 for more time than is set in parameter L6-03.
Torque Detection 2 Closed: When the output current/torque exceeds the value set in
18 O O O —
(N.O.) parameter L6-05 for more time than is set in parameter L6-06.
Torque Detection 2 Open: Output current/torque exceeds the value set in parameter
19 O O O —
(N.C.) L6-05 for more time than is set in parameter L6-06.
1A Reverse Direction Closed: Drive is running in the reverse direction. O O O —

346 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 B.2 Parameter Table

H2 Multi-Function Digital Output Settings

Control
Mode
H2-
Setting Function Description O Pg.
V/ L P
f M
V
1B Baseblock 2 Open: Drive is in base block condition. Output is disabled. O O O —
1C Motor 2 Selection Closed: Motor 2 is selected by a digital input (H1- = 16) O O − —
1E Restart Enabled Closed: An automatic restart is performed O O O —
1F Overload Alarm OL1 Closed: OL1 is at 90% of its trip point or greater. O O O —
20 OH Pre alarm Closed: Heatsink temperature exceeds the parameter L8-02 value. O O O —
Mechanical Weakening
22 Closed: Mechanical Weakening detected. O O O —
(N.O.)
30 During Torque Limit Closed: When the torque limit has been reached. − O − —
Closed: Frequency is output
During Frequency
37 Open: Operation stopped, Baseblock, DC Injection Braking, or O O O —
Output
Initial Excitation is being performed.
38 Drive Enable Closed: Multi-function input closes (H1- = 6A) O O O —
Watt Hour Pulse Output units are determined by H2-06, outputs 200 ms pulse for
39 O O O —
Output each incremented kWh count.
Closed: Local
3C Drive Mode O O O —
Open: Remote(this signal combines setting values 9 and A).
3D Speed Search Closed: Speed search is being executed. O O O —
Closed: PID Feedback Loss.
3E PID Feedback Loss PID feedback value is below the level set to b5-13 for longer than O O O —

Parameter List
the time set in b5-14.
Closed: PID Feedback Fault.PID feedback value exceeds the level
3F PID Feedback Fault O O O —
set to b5-36 for longer than the time set to b5-37.
4A KEB Operation Closed: KEB is being performed. O O O —
4B Short-Circuit Brake Closed: Short-Circuit Braking is active. − − O —
4C During Fast-stop Closed: Fast-stop command is entered O O O — B
OH Pre-alarm Time
4D Closed: OH Pre-alarm time limit is passed. O O O —
Limit
Reverse the output switching of the multi-function output
functions. Set the last two digits of 1 to reverse the output
H2 Parameter
signal of that specific function.Examples:
100 to Functions Reversed
Setting “108” reverses the output of “During baseblock,” which is O O O —
14D Output Switching of 0
setting value 08.
to 92
Setting “14A” reverses the output of “During KEB operation”,
which is setting “4A”.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 347
B.2 Parameter Table

Control
Mode
No. Name Description Range Def. O Addr. Pg.
V/ L P Hex
f M
V
H3: Analog Inputs
Use H3 parameters to set the multi-function analog input terminals.
Sets the input level for terminal A1.
Terminal A1 Signal
H3-01 0: 0 to +10 V (lower limit) 0, 1 0 A A A 410 —
Level Selection
1: 0 to +10 V (no lower limit)
Sets the function of terminal A1. When
Terminal A1 Function 0 to 31
H3-02 terminal A1 is not used or is used as a through 0 A A A 434 —
Selection <40>
terminal, this parameter must be set to “F”.
H3-03 Terminal A1 Gain Sets the level of the input value selected in -999.9 to 100.
A A A 411 —
<22> Setting H3-02 when 10V is input at terminal A1. 999.9 0%
H3-04 Terminal A1 Bias Sets the level of the input value selected in -999.9 to 0.0
A A A 412 —
<22> Setting H3-02 when 0V is input at terminal A1. 999.9 %
Sets the input signal level for terminal A2. 0 to 3 2 A A A 417 —
0: 0 to +10 V (with lower limit) Switch between current or voltage
Terminal A2 Signal
H3-09 1: 0 to +10 V (no lower limit) inputs by using DIP switch S1-2
Level Selection
2: 4 to 20 mA switch on the terminal board. Refer
3: 0 to 20 mA to I/O Connections on page 77.
Sets the function of terminal A2. When
Terminal A2 Function 0 to 31
H3-10 terminal A2 is not used or is used as a through 0 A A A 418 —
Selection <40>
terminal, this parameter must be set to “F”.
Sets the level of the input value selected in
H3-11 Terminal A2 Gain -999.9 to 100.
H3-10 when 10 V (20 mA) is input at terminal A A A 419 —
<22> Setting 1000.0 0%
A2.
Sets the level of the input value selected in
H3-12 Terminal A2 Input -999.9 to 0.0
H3-10 when 0 V (0 or 4 mA) is input at A A A 41A —
<22> Bias 999.- %
terminal A2.
Analog Input Filter Sets the primary delay filter time constant for 0.00 to 0.0
H3-13 A A A 41B —
Time Constant terminals A1 and A2. Used for noise filtering. 2.00 3s

<22> Parameter can be changed during run.

<40> The availability of certain parameters depends on the control method used.

H3 Multi-Function Analog Input Settings

Control
H3- Mode
Setting Function Maximum Input Level Possible Pg.
V/ O P
f LV M
Max output frequency (E1-04).Same value can be set
0 Frequency Bias O O O —
using H3-02 and H3-10.

348 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 B.2 Parameter Table

H3 Multi-Function Analog Input Settings

Control
H3- Mode
Setting Function Maximum Input Level Possible Pg.
V/ O P
f LV M
1 Frequency Gain Frequency reference (voltage) O O O —
Auxiliary Frequency Reference
2 Max output frequency (E1-04) O O O —
(used as a multi step speed 2)
4 Output Voltage Bias Motor rated voltage (E1-05). O – − —
Overtorque/Undertorque Open Loop Vector: Motor rated torque
7 O O O —
Detection Level V/f control: Drive rated current
B PID Feedback 10V = 100% O O O —
C PID Set Point 10V = 100% O O O —
E Motor Temperature (PTC input) 10 V = 100.00% Determined by L1-03 and L1-04. O O O —
F Not used / Pass-through mode – O O O —
10 FWD Torque Limit Motor rated torque − O − —
11 REV Torque Limit Motor rated torque − O − —
12 Regenerative Torque Limit Motor rated torque − O − —
15 FWD/REV Torque Limit Motor rated torque − O − —
16 Differential PID Feedback 10 V = 100% O O O —

Control
Mode

Parameter List
No. Name Description Range Def. Addr. Pg.
V/ O P Hex
L M
f V

H4: Multi-Function Analog Outputs

Use H4 parameters to configure the multi-function analog output terminals.
Selects the data to be output through multi-

Multi-Function
function analog output terminal AM. Set the
desired monitor parameter to the digits 000 to
B
H4-01 Analog Output available in U†-††. For example, enter 999 102 A A A 41D —
Terminal AM) “103” for U1-03. <40>
When using this terminal in trough mode or
when not using it at all, set “000” or “031”.
Multi-Function Sets terminal AM output level when selected -999.9
H4-02 100.
Analog Output monitor is at 100%. Maximum output voltage to S S S 41E —
<22> 0%
Terminal AM Gain is 10 V. 999.9
Multi-Function -999.9
H4-03 Sets terminal AM output level when selected 0.0
Analog Output to A A A 41F —
<22> monitor is at 0%. %
Terminal AM Gain 999.9

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 349
B.2 Parameter Table

Control
Mode
No. Name Description Range Def. Addr. Pg.
V/ O P Hex
f L M
V
H5: MEMOBUS/Modbus Communications
Use H5 Parameters to connect the drive to a MEMOBUS/Modbus network.
Selects drive station node number (address) for
H5-01 0 to 20
Drive Node Address MEMOBUS/Modbus terminals R+, R-, S+, S-. 1F A A A 425 —
<39> H
Cycle power for the setting to take effect.
Selects the baud rate for MEMOBUS/Modbus
terminals R+, R-, S+ and S-. Cycle power for
the setting to take effect.
0: 1200 bps
1: 2400 bps
Communication 2: 4800 bps
H5-02 0 to 8 3 A A A 426 —
Speed Selection 3: 9600 bps
4: 19200 bps
5: 38400 bps
6: 57600 bps
7: 76800 bps
8: 115200 bps
Selects the communication parity for
MEMOBUS/Modbus terminals R+, R-, S+ and
Communication S-. Cycle power for the setting to take effect.
H5-03 0 to 2 0 A A A 427 —
Parity Selection 0: No parity
1: Even parity
2: Odd parity
Selects the stopping method when a
communication time-out fault (CE) is detected.
Stopping Method
0: Ramp to stop
H5-04 After Communication 0 to 3 3 A A A 428 —
1: Coast to stop
Error
2: Fast-stop
3: Alarm only
Enables or disables the communications time-
out fault (CE) detection.
Communication Fault
H5-05 0: Disabled 0,1 1 A A A 429 —
Detection Selection
1: Enabled - If communication is lost for more
than two seconds, a CE fault will occur.
Drive Transmit Wait Set the wait time between receiving and
H5-06 5 to 65 5 ms A A A 42A —
Time sending data.
Selects "request to send" (RTS) control:
RTS Control
H5-07 0: Disabled - RTS is always on. 0,1 1 A A A 42B —
Selection
1: Enabled - RTS turns on only when sending.
Sets the time required to detect a
0.0 to
H5-09 CE Detection Time communications error. Adjustment may be 2.0 s A A A 435 —
10.0 s
need when networking several drives.

350 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 B.2 Parameter Table

Control
Mode
No. Name Description Range Def. Addr. Pg.
V/ O P Hex
f L M
V
Selects the units used for MEMOBUS/Modbus
Unit Selection for register 0025H (Output Voltage Reference
H5-10 MEMOBUS/Modbus Monitor). 0, 1 0 A A A 436 —
Register 0025H 0: 0.1 V units
1: 1 V units
Select the function for the enter command that
saves parameter data to the drive.
Communications 0: Parameter changes are activated when
H5-11 ENTER Function ENTER command is entered. 0, 1 1 A A A 43C —
Selection 1: Parameter changes are activated
immediately without ENTER command
(compatible with Varispeed VS606-V7).
Run Command 0: FWD/STOP, REV/STOP Method
H5-12 0, 1 0 A A A 43D —
Method Selection 1: RUN/STOP, FWD/REV Method
H6: Pulse Train Input/Output
Use H6 parameters to configure Pulse Train I/O operation.
Selects pulse train input function.
0: Frequency reference
Pulse Train Input 1: PID feedback value
H6-01 Terminal RP Function 2: PID setpoint value 0 to 3 0 A A A 42C —
Selection 3: Simple PG V/f control mode (can be set
only when using motor 1 in the V/f control
mode)

Parameter List
H6-02 Pulse Train Input Sets the number of pulses (Hz) that is equal to 1000 to 1440
A A A 42D —
<22> Scaling 100% of the value selected in H6-01. 32000 Hz
Sets the level of the value selected in H6-01
H6-03 Pulse Train Input 0.0 to 100.
when a frequency with the value set in H6-02 A A A 42E —
<22> Gain 1000.0 0%
is input.
-100.0
H6-04
<22>
Pulse Train Input Bias
Sets the level of the value selected in H6-01
when 0 Hz is input.
to
0.0
%
A A A 42F — B
+100.0
H6-05 Pulse Train Input 0.00 to 0.10
Sets the pulse train input filter time constant. A A A 430 —
<22> Filter Time 2.00 s
000,
Select the pulse train monitor output function
031,
(value of the †-†† part of U†-††). Refer
101,
Pulse Train Monitor to U: Monitors on page 376 for the list of U
H6-06 102,
Terminal MP monitors. 102 A A A 431 —
<22> 105,
Selection Example: To select U5-01, set “501.”
116,
When not using this parameter or when using
501,
in the through mode, set “000”.
502

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 351
B.2 Parameter Table

Control
Mode
No. Name Description Range Def. Addr. Pg.
V/ O P Hex
f L M
V
Sets the pulse output frequency in Hz when the
H6-07 Pulse Train Monitor monitor value is 100%. Set H6-06 to “2” and 0 to 1440
A A A 432 —
<22> Scaling H6-07 to “0”, to make the pulse train monitor 32000 Hz
output equal to the output frequency.

<22> Parameter can be changed during run.

<39> If this parameter is set to 0, the drive will be unable to respond to MEMOBUS/Modbus commands.
<40> The availability of certain functions depends on the control method used.

Note: Cycle power to the drive to enable MEMOBUS/Modbus settings.

◆ L: Protection Function
L parameters provide protection to the drive and motor, such as: control during momentary
power loss, stall prevention, frequency detection, fault restarts, overtorque detection, torque
limits and other types of hardware protection.

Control
Mode
No. Name Description Range Def. Addr. Pg.
V/ O P Hex
f VL M

L1: Motor Protection Functions

Use L1 parameters to configure motor protective functions.
Sets the motor thermal overload protection
(OL1) based on the cooling capacity of the
motor.
0: Disabled
1: Standard Fan Cooled (< 10:1 motor)
2: Standard Blower Cooled (≥ 10:1 motor)
Motor Overload 3: Vector Motor (100:1 motor) 1
L1-01 0 to 4 S S S 480 401
Protection Selection 4: PM motor with variable torqueNOTICE: <2>
The thermal protection is reset when the power
is cycled. In applications where the power is
frequently cycled, the drive may not be able to
provide protection, even if this parameter is set
to 1. Set to “0” and ensure each motor has a
thermal relay installed.

352 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 B.2 Parameter Table

Control
Mode
No. Name Description Range Def. Addr. Pg.
V/ O P Hex
f L M
V
Sets the motor thermal overload protection
(OL1) time. A larger L1-02 time will increase
Motor Overload the time for an OL1 fault to occur. 0.1 to 1.0
L1-02 A A A 481 —
Protection Time This parameter does not typically require 5.0 min
adjustment. Should be set in accordance with
the overload tolerance of the motor.
Sets operation when the motor temperature
analog input (H3-02/10 = E) exceeds the OH3
Motor Overheat alarm level.
L1-03 Alarm Operation 0: Ramp to Stop 0 to 3 3 A A A 482 —
Selection (PTC input) 1: Coast to Stop
2: Fast-stop using C1-09
3: Alarm Only (“oH3” will flash)
Sets stopping method when the motor
temperature analog input (H3-02/10 = E)
Motor Overheat Fault
exceeds the OH4 fault level.
L1-04 Operation Selection 0 to 2 1 A A A 483 —
0: Ramp to Stop
(PTC input)
1: Coast to Stop
2: Fast-stop
This parameter adjusts the filter on the motor
Motor Temperature
temperature analog input (H3-02 or H3-10 = 0.00 to 0.20
L1-05 Input Filter Time A A A 484 —
E). Increase to add stability, decrease to 10.00 s
(PTC input)
improve response.

Parameter List
Determines whether or not to hold the
Continuous electrothermal value when the power supply is
L1-13 Electrothermal interrupted. 0 to 1 1 A A A 46D —
Operation Selection 0: Disabled
1: Enabled
L2: Momentary Power Loss
Use L2 parameters to configure drive functions for momentary power loss conditions.
Enables and disables the momentary power 0 to 2 0 A A A 485
B
loss function.
0: Disabled - Drive trips on (UV1) fault when
Momentary Power power is lost. For a restart to occur, the run
L2-01 Loss Operation 1: Power Loss Ride-Thru Time - Drive will command must be maintained —
Selection restart if power returns within the time set in throughout the ride-thru
L2-02. period.
2: CPU Power Active - Drive will restart if
power returns as long as the CPU is working.
Momentary Power Sets the Power Loss Ride-Thru time. Only 0.0 to
L2-02 <12> A A A 486 —
Loss Ride-Thru Time effective when L2-01 = 1. 25.5

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 353
B.2 Parameter Table

Control
Mode
No. Name Description Range Def. Addr. Pg.
V/ O P Hex
f L M
V
Sets the minimum wait time for residual motor
Momentary Power voltage decay before the drive output
0.1 to
L2-03 Loss Minimum reenergizes after power loss ride-thru. If L2-03 <57> A A A 487 —
5.0
Baseblock Time is greater than L2-02, operation resumes after
the time set in L2-03.
Momentary Power
Sets the time for the output voltage to return to 0.0 to
L2-04 Loss Voltage <12> A A A 488 —
the preset V/f pattern during speed search. 5.0
Recovery Ramp Time
Sets the DC Bus undervoltage trip level. If this
is set lower than the default setting, additional
AC input impedance or DC bus reactance may
L2-05 Undervoltage 150 to <9>
be necessary. Consult with the manufacturer A A A 489 —
<24> Detection Level (UV) 210 <12>
before changing this parameter setting.
This value is used for KEB activation if L2-01
> 0.
KEB Deceleration Sets the time required to decelerate from the 0.0 to
L2-06 0.0 s A A A 48A —
Time speed when KEB was activated to zero speed. 200.0
Set the time to accelerate to the set speed after
KEB Acceleration 0.0 to
L2-07 recovery from a momentary power loss. If set 0.0 s A A A 48B —
Time 25.5
to 0.0, the active acceleration time is used.
Sets the percentage of output frequency
reduction at the beginning of deceleration
KEB Start Output when a KEB command is input from multi- 100
L2-08 0 to 300 A A A 48C —
Frequency Reduction function input. %
Reduction = (slip frequency before KEB) x
L2-08 x 2
E1-
L2-11 Desired DC Bus Sets the desired value of the DC bus voltage 150 to
01 A A A 461 —
<24> Voltage during KEB during KEB. 400 V
1.22

354 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 B.2 Parameter Table

Control
Mode
No. Name Description Range Def. Addr. Pg.
V/ O P Hex
f L M
V
L3: Stall Prevention Function
Use L3 parameters to configure the stall prevention function.
Selects the stall prevention method used to
prevent excessive current during acceleration.
0: Disabled - Motor accelerates at active
acceleration rate. The motor may stall if load is
too heavy or accel time is too short.
Stall Prevention 1: General Purpose - When output current
0 to 2
L3-01 Selection during exceeds L3-02 level, acceleration stops. 1 A A A 48F —
<29>
Acceleration Acceleration will continue when the output
current level falls below the L3-02 level.
2: Intelligent - The active acceleration rate is
ignored. Acceleration is completed in the
shortest amount of time without exceeding the
current value set in L3-02.
Used when L3-01 = 1 or 2.
Stall Prevention Level 100% is equal to the drive rated current.
L3-02 0 to 150 <7> A A A 490 —
during Acceleration Decrease the set value if stalling or excessive
current occurs with default setting.
Sets stall prevention lower limit during
Stall Prevention Limit acceleration when operating in the constant
L3-03 0 to 100 50% A A A 491 —
during Acceleration power range. Set as a percentage of the drive's
rated current.

Parameter List
B

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 355
B.2 Parameter Table

Control
Mode
No. Name Description Range Def. Addr. Pg.
V/ O P Hex
f L M
V
When using a braking resistor, use setting "0".
Setting "3" is used in specific applications.
0: Disabled - The drive decelerates at the active
deceleration rate. If the load is too large or the
deceleration time is too short, an OV fault may
occur.
1: General Purpose - The drive decelerates at
the active deceleration rate, but if the main
circuit DC bus voltage reaches the stall
prevention level (380/760 VDC), deceleration
Stall Prevention will stop. Deceleration will continue once the
0 to 4
L3-04 Selection during DC bus level drops below the stall prevention 1 S S S 492 356
<50>
Deceleration level.
2: Intelligent - The active deceleration rate is
ignored and the drive decelerates as fast as
possible without hitting OV fault level.
Range: C1-02 / 10.
3: Stall Prevention with Braking Resistor -
Stall prevention during deceleration is enabled
in coordination with dynamic braking.
4: Overexcitation Deceleration - Decelerates
with the flux level determined by n3-13
(Overexcitation Gain).
Selects the stall prevention method to use to
prevent drive faults during run.
0: Disabled - Drive runs a set frequency. A
heavy load may cause the drive to trip on an
OC or OL fault.
1: Decel Time 1 - The drive will decelerate at
Decel Time 1 (C1-02) if the output current
Stall Prevention exceeds the level set by L3-06. Once the
L3-05 0 to 2 1 A − A 493 —
Selection during Run current level drops below the L3-06 level, the
drive will accelerate back to its frequency
reference at the active acceleration rate.
2: Decel Time 2 - Same as setting 1 except the
drive decelerates at Decel Time 2 (C1-04).
When output frequency is 6 Hz or less, stall
prevention during run is disabled regardless of
the setting in L3-05.
Enabled when L3-05 is set to "1" or "2". 100%
Stall Prevention Level is equal to the drive rated current.Decrease the 30 to
L3-06 <7> A − A 494 —
during Run set value if stalling or excessive current occurs 200
with the default settings.

356 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 B.2 Parameter Table

Control
Mode
No. Name Description Range Def. Addr. Pg.
V/ O P Hex
f L M
V
Enables or disables OV suppression function,
which allows the drive to change the output
frequency as the load changes, thus preventing
an OV fault.
0: Disabled
OV Suppression
L3-11 1: Enabled 0, 1 0 A A - 4C7 —
Function Selection
Note: The frequency reference and motor
speed diverge as the regenerative energy
begins to flow back into the DC bus and
triggers the OV suppression function. Disable
this function when using a braking resistor.
Overvoltage Sets the desired value for the DC bus voltage
370
L3-17 Suppression and Stall during overvoltage suppression and stall 150 to
V A A A 462 —
<24> Prevention Desired prevention during deceleration. Enabled only 400 V
<9>
DC Bus Voltage when L3-04 = 2.
Sets the proportional gain used by KEB, Stall
Main Power Circuit prevention and overvoltage suppression.
0.00 to
L3-20 Voltage Adjustment If OV or UV1 occurs at the beginning of KEB 1.00 A A A 465 —
5.00
Gain deceleration, slowly increase this setting by
0.1.
Sets the proportional gain used to calculate the
deceleration rate during KEB, OV suppression
function and stall prevention during
Accel/Decel Rate 0.00 to
L3-21 deceleration (L3-04 = 2). 1.00 A A A 466 —

Parameter List
Calculation Gain 200.00
This parameter does not typically require
adjustment. Increase the value in steps of 1.0 if
overcurrent and overvoltage occur.
Sets the deceleration time used for stall
Deceleration Time at prevention during acceleration in Open Loop
0.0 to
L3-22 Stall Prevention Vector control for PM motors. 0.0 s − − A 4F9 —
during Acceleration When set to 0, the drive decelerates at the
normal deceleration time.
6000.0
B
0: Sets the stall prevention level throughout the
Automatic Reduction entire frequency range to the value in
Selection for Stall parameter L3-06.
L3-23 0, 1 0 A A Α 4FD —
Prevention during 1: Automatically lowers the stall prevention
Run level in the constant output range. The lower
limit value is 40% of L3-06.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 357
B.2 Parameter Table

Control
Mode
No. Name Description Range Def. Addr. Pg.
V/ O P Hex
f L M
V
Sets the time needed to accelerate the
uncoupled motor at rated torque from stop to
Motor Acceleration
the maximum frequency. 0.001 to
L3-24 Time for Inertia <57> A A A 46E —
Setting the drive capacity to parameter o2-04 10.000
Calculations
or changing E2-11 will automatically set this
parameter for a 4-pole motor.
Sets the ratio between the motor and machine 0.0 to
L3-25 Load Inertia Ratio 1.0 A A A 46F —
inertia. 1000.0
L4: Frequency Detection
Use L4 parameters to configure frequency detection operation.
Speed Agreement These parameters configure the multi-function 0.0 to 0.0
L4-01 A A A 499 —
Detection Level output (H2-†† = 2, 3, 4, 5) settings "Fref/ 400.0 Hz
Fout Agree 1", "Fref/Set Agree 1", "Frequency
Detection 1," and "Frequency detection 2".
Speed Agreement Parameter L4-01 sets the level while parameter 0.0 to 2.0
L4-02 A A A 49A —
Detection Width L4-02 sets the hysteresis for the Speed 20.0 Hz
Detection Output Function.
These parameters configure the Multi-Function -400.0
Speed Agreement 0.0
L4-03 Output (H2-†† = 13, 14, 15, 16) settings to A A A 49B —
Detection Level (+/-) Hz
"Fref/Fout Agree 2", "Fref/Set Agree 2", +400.0
"Frequency Detection 3," or "Frequency
Detection 4".
Speed Agreement Parameter L4-03 sets the level while parameter 0.0 to 2.0
L4-04 A A A 49C —
Detection Width (+/-) L4-04 sets the hysteresis for the Speed 20.0 Hz
Detection Output Function.
Sets operation when the frequency reference is
lost (reference drops 90% or more of within
Frequency Reference 400 ms).
L4-05 Loss Detection 0: Stop - Drive will stop. 0,1 0 A A A 49D —
Selection 1: Run at L4-06 PrevRef - Drive will run at the
percentage set in L4-06 of the frequency
reference before loss.
Sets the frequency reference when a reference
Frequency Reference 0.0 to 80.0
L4-06 loss was detected and L4-05 = 1. Reference A A A 4C2 —
at Reference Loss 100.0 %
will be: Fref = Fref at time of loss L4-06.
Frequency Detection 0: No detection during baseblock.
L4-07 0 to 1 0 A A A 470H —
Conditions 1: Detection always enabled.

358 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 B.2 Parameter Table

Control
Mode
No. Name Description Range Def. Addr. Pg.
V/ O P Hex
f L M
V
L5: Fault Reset
Use L5 parameters to configure Automatic Restart after fault.
Sets the counter for the number of times the
drive attempts to restart when the following
faults occur: GF, LF, OC, OV, PF, PUF, RH,
Number of Auto RR, OL1, OL2, OL3, OL4, UV1. If the drive
L5-01 0 to 10 0 A A A 49E —
Restart Attempts faults after an auto restart attempt, the counter
is incremented.
When the drive operates without fault for 10
minutes, the counter will be reset.
Sets fault contact activation during automatic
restart attempts.
Auto Restart
L5-02 0: Fault output (H2-oo = E) not active. 0,1 0 A A A 49F —
Operation Selection
1: Fault output (H2-oo = E) active during
restart attempt.
Sets the amount of time to wait between
Fault Reset Interval 0.5 to 10.0
L5-04 performing fault restarts. Enabled when L5-05 A A A 46C —
Time 600.0 s s
is set to 1.
Selects the method of incrementing the restart
counter.
0: Continuously attempt to restart and
Fault Reset Operation increment counter after successful restart (like
L5-05 0 to 1 0 A A A 467 —
Selection Varispeed VS616-F7/G7)

Parameter List
1: Attempt to restart with the interval time set
in L5-04. Every trial increments the counter.
(like Varispeed VS606-V7)

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 359
B.2 Parameter Table

Control
Mode
No. Name Description Range Def. Addr. Pg.
V/ O P Hex
f L M
V
L6: Overtorque Detection
Use L6 parameters to configure overtorque detection.
Selects the overtorque/undertorque operation.
overtorque and undertorque are determined by
the settings in parameters L6-02 and L6-03.
The multi-function output settings (H2-†† =
B and 17) are also active if programmed.
0: Disabled
1: OL3 at Speed Agree - Alarm (overtorque
detection only active during Speed Agree and
operation continues after detection).
2: OL3 at RUN - Alarm (overtorque detection
is always active and operation continues after
detection).
3: OL3 at Speed Agree - Fault (overtorque
detection only active during Speed Agree and
Torque Detection drive output will shut down on an OL3 fault).
L6-01 0 to 8 0 A A A 4A1 —
Selection 1 4: OL3 at RUN - Fault (overtorque detection is
always active and drive output will shut down
on an OL3 fault).
5: UL3 at Speed Agree - Alarm (undertorque
detection is only active during Speed Agree
and operation continues after detection).
6: UL3 at RUN - Alarm (undertorque detection
is always active and operation continues after
detection).
7: UL3 at Speed Agree - Fault (undertorque
detection only active during Speed Agree and
drive output will shut down on an OL3 fault).
8: UL3 at RUN - Fault (undertorque detection
is always active and drive output will shut
down on an OL3 fault).
Sets the overtorque/undertorque detection
Torque Detection level. 100% is equal to the motor rated current 150
L6-02 0 to 300 A A A 4A2 —
Level 1 in V/f control and the motor rated torque in %
Open Loop Vector control.
Sets the length of time an overtorque/
Torque Detection 0.0 to
L6-03 undertorque condition must exist before 0.1 s A A A 4A3 —
Time 1 10.0
Torque Detection 1 is triggered.

360 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 B.2 Parameter Table

Control
Mode
No. Name Description Range Def. Addr. Pg.
V/ O P Hex
f L M
V
Sets the response to an overtorque/undertorque
condition. overtorque and undertorque are
determined by the settings in parameters L6-05
and L6-06. The multi-function output settings
(H2-†† = 18 and 19).
0: Disabled
1: OL4 at Speed Agree - Alarm (overtorque
Detection only active during Speed Agree and
Operation continues after detection).
2: OL4 at RUN - Alarm (overtorque Detection
is always active and operation continues after
detection).
3: OL4 at Speed Agree - Fault (overtorque
Detection only active during Speed Agree and
Torque Detection drive output will shut down on an OL4 fault).
L6-04 0 to 8 0 A A A 4A4 —
Selection 2 4: OL4 at RUN - Fault (overtorque Detection
is always active and drive output will shut
down on an OL4 fault).
5: UL4 at Speed Agree - Alarm (undertorque
Detection is only active during Speed Agree
and operation continues after detection).
6: UL4 at RUN - Alarm (undertorque
Detection is always active and operation
continues after detection).
7: UL4 at Speed Agree - Fault (undertorque

Parameter List
Detection only active during Speed Agree and
drive output will shut down on an OL4 fault).
8: UL4 at RUN - Fault (undertorque Detection
is always active and drive output will shut
down on an OL4 fault).
Sets the overtorque/undertorque detection
L6-05
Torque Detection
Level 2
level. 100% is equal to the motor rated current
in V/f control and the motor rated torque in
0 to 300
150
%
A A A 4A5 — B
Open Loop Vector control.
Sets the length of time an overtorque/
Torque Detection 0.0 to
L6-06 undertorque condition must exist before torque 0.1 s A A A 4A6 —
Time 2 10.0
detection 2 is recognized by the drive.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 361
B.2 Parameter Table

Control
Mode
No. Name Description Range Def. Addr. Pg.
V/ O P Hex
f L M
V
This function can detect an over/undertorque in
a certain speed range as a result of machine
fatigue. It is triggered by a certain operation
time and uses the OL1 detection settings (L6-
01 to L6-03)
0: Mechanical Weakening Detection disabled.
1: Continue running if the speed (signed) is
greater than L6-09 (alarm only).
2: Continue running if the speed (not signed) is
greater than L6-09 (alarm only).
3: Interrupt drive output when the motor speed
(signed) is greater than L6-09 (protection
Mechanical
operation).
L6-08 Weakening (OL5) 0 to 8 0 A A A 468 —
4: Interrupt drive output when the motor speed
Detection Operation
(not signed) is greater than L6-09 (protection
operation).
5: Continue running if the speed (signed) is
less than L6-09 (alarm only).
6: Continue running if the speed (not signed) is
less than L6-09 (alarm only).
7: Interrupt drive output when the motor speed
(signed) is less than L6-09 (protection
operation).
8: Interrupt drive output when the motor speed
(not signed) is less than L6-09 (protection
operation).
• Sets the speed that triggers mechanical
-110.0
Mechanical weakening detection.
to 110
L6-09 Weakening Detection • When L6-08 is set for an unsigned value, the A A A 469 —
+110.0 %
Speed Level absolute value is used even if the setting is
%
negative.
Mechanical
Sets the time a mechanical weakening has to be 0.0 to
L6-10 Weakening Detection 0.1 s A A A 46A —
detected before an Alarm/Fault is triggered. 10.0 s
Time
Mechanical Sets the operation time (U1-04) that has to be
0 to
L6-11 Weakening Detection passed before Mechanical weakening detection 0 A A A 46B —
65535
Start Time is active.

362 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 B.2 Parameter Table

Control
Mode
No. Name Description Range Def. Addr. Pg.
V/ O P Hex
f L M
V
L7: Torque Limit
Use L7 parameters to configure the torque limit function.
Sets the torque limit value as a percentage of 200
L7-01 Forward Torque Limit 0 to 300 − A − 4A7 —
the motor rated torque. Four individual %
quadrants can be set. 200
L7-02 Reverse Torque Limit 0 to 300 − A − 4A8 —
output torque %
Forward Regenerative positive torque 200
L7-03 L7-01 0 to 300 − A − 4A9 —
Torque Limit L7-04 motor
%
regeneration r/min
REV FWD
Reverse Regenerative regeneration 200
L7-04 0 to 300 − A − 4AA —
Torque Limit L7-03 %
L7-02
negative torque

Torque Limit Integral Sets the integral time constant for the torque 5 to 200
L7-06 − A − 4AC —
Time Constant limit. 10000 ms
Selects the method of torque limit control
during accel/decel.
0: Proportional Control (change to integral
controls at fixed speeds). Use this setting when
Torque Limit Control acceleration to the desired speed has priority
L7-07 Method Selection over torque limitation. 0, 1 0 − A − 4C9 —
during Accel/Decel 1: Integral Control. Use this setting if the

Parameter List
torque limitation has priority.
When torque limit is applied to the motor,
accel/decel time may increase and motor speed
may not meet the speed reference.
L8: Hardware Protection
Use L8 parameters to configure hardware protection functions.

Internal Dynamic
Selects the Braking resistor when using a 3%
duty cycle heatsink mounted Yaskawa braking
B
Braking Resistor resistor. This parameter does not enable or
L8-01 0,1 0 A A A 4AD —
Protection Selection disable the braking transistor of the drive.
(ERF type) 0: Resistor overheat protection disabled
1: Resistor overheat protection enabled
When the heatsink temperature exceeds the
Overheat Alarm 50 to
L8-02 value set in this parameter, an Overheat Alarm <12> A A A 4AE —
Level 130
(OH) will occur.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 363
B.2 Parameter Table

Control
Mode
No. Name Description Range Def. Addr. Pg.
V/ O P Hex
f L M
V
Sets the drive operation when an overheat
alarm OH is detected.
0: Ramp to Stop using the active decel time.
1: Coast to Stop.
2: Fast-stop using the time set in C1-09.
Overheat Pre-Alarm 3: Alarm Only. Drive continues running, but
L8-03 0 to 4 3 A A A 4AF —
Operation Selection displays an alarm.
4: Reduced Speed Operation. Drive continues
to run with reduced frequency reference as
specified in L8-19.
Settings 0 through 2 trigger a fault relay if the
heatsink becomes too hot.
Selects the detection of input current phase
loss, power supply voltage imbalance, or main
Input Phase Loss 1
L8-05 circuit electrolytic capacitor deterioration. 0,1 A A A 4B1 —
Protection Selection <56>
0: Disabled
1: Enabled
Selects the output phase loss detection.
0: Disabled
1: Enabled (triggered by a single phase loss).
2: Enabled (triggered when two phases are
Output Phase Loss lost).Output phase loss is detected when
L8-07 0 to 2 0 A A A 4B3 —
Protection operating with less than 5% of the drive rated
current. Detection can mistakenly occur if the
motor is too small relative to the drive capacity
rating (this parameter should be disabled in
such cases).
Selects the output ground fault detection.
Output Ground Fault
L8-09 0: Disabled 0,1 <12> A A A 4B5 —
Detection Selection
1: Enabled
Controls the heatsink cooling fan operation.
0: Fan On-Run Mode - Fan will operate only
Heatsink Cooling Fan when the drive is running and for L8-11
L8-10 0,1 0 A A A 4B6 —
Operation Selection seconds after stop.
1: Fan always on - Cooling fan operates
whenever the drive is powered up.
Heatsink Cooling Fan This parameter sets the delay time for the
L8-11 Operation Delay cooling fan to shut off after the run command 0 to 300 60 s A A A 4B7 —
Time is removed when L8-10 = 0.
Ambient Temperature Used to input the ambient temperature. This -10 to 40
L8-12 A A A 4B8 —
Setting value adjusts the drives OL2 detection level. 50 °C

364 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 B.2 Parameter Table

Control
Mode
No. Name Description Range Def. Addr. Pg.
V/ O P Hex
f L M
V
Sets the OL2 characteristics at output
OL2 Characteristics frequencies below 6 Hz.
L8-15 Selection at Low 0: No OL2 level reduction below 6Hz. 0,1 1 A A A 4BB —
Speeds 1: OL2 level is reduced linearly below 6 Hz. It
is halved at 0 Hz.
Selects the software current limit function.
Typically no adjustment is required.
L8-18 Soft CLA Selection 0,1 1 A A − 4BE —
0: Disabled
1: Enabled
Frequency Reduction
Specifies the frequency reference reduction 0.1 to
L8-19 Rate during OH 0.8 A A A 4BF —
gain at overheat prealarm when L8-03 = 4. 1.0
Pre-Alarm
Selects the detection of unbalanced output
currents caused by faulty devices in the output
Current Unbalance
L8-29 circuit. 0 to 1 1 − − A 4DF —
Detection (LF2)
0: Disabled
1: Enabled
Selects the installation type:
0: Standard installation of Open Chassis drive
Side-by-Side <12>
L8-35 1: Side-by-Side installation with top cover 0 to 2 Α Α A 4ECH —
Selection <25>
removed
2: Standard Installation of NEMA Type 1 drive
Provides protection to the IGBTs by reducing

Parameter List
the carrier frequency at low speeds.
Carrier Frequency
L8-38 0: Disabled 0 to 2 0 A A A 4EF —
Reduction
1: Enabled below 6Hz
2: Enabled for the whole speed range
Sets the time for that the drive continues
running with reduced carrier frequency after
L8-40
Carrier Frequency
Reduction Time
the carrier reduction condition has gone (see
also L8-38).
0.00 to
2.00
0.50 A A A 4F1 B
A setting of 0.00 s disables the carrier
frequency reduction time.
Configures an alarm when the output current
Current Alarm exceeds 150% of the drive rated current.
L8-41 0,1 0 A A A 4F2 —
Selection 0: Alarm disabled.
1: Alarm enabled (alsarm is output).

<1> Default setting value is dependent on parameter A1-02, Control Method Selection. The value shown is for A1-02
= 2-OLV control.
<2> Default setting value is dependent on parameter A1-02, Control Method Selection. The value shown is for A1-02
= 0-V/f Control.
<7> Default setting value is 120% when C6-01 is set to 1 (ND) and 150% when C6-01 is set to 0 (HD).
<9> Default setting value is dependent on parameter E1-01, Input Voltage Setting.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 365
B.2 Parameter Table

<12> Default setting value is dependent on parameter o2-04, Drive/kVA Selection.

<14> Default setting value is dependent on parameter o2-09, Initialization Spec. Selection.
<15> Default setting value is dependent on parameter A1-02, Control Method Selection. The value shown is for A1-02
= 5-PM OLV Control.
<24> Values shown here are for 200 V class drives. Double the value when using a 400 V class drive.
<25> Parameter setting value is not reset to the default value during drive initializaion, A1-03 = 1110, 2220, 3330.
<29> Setting value 2 is not available A1-02 = 5-PM OLV Control. When enabled, the drive stops accelerating when it
exceeds the value of L3-02, Stall Prevention Level. The drive decelerates after 100 ms and begins accelerating
again after restoring the current level.
<31> Use caution when working with regenerative loads as motor speed can exceed the frequency reference during
overvoltage suppression function operation. Set to "Disable" when motor speed needs to accurately match the
frequency reference, and also when using a braking resistor. An OV fault may still occur even when this function
is enabled if there is a sudden increase in the regenerative load.
<50> The setting range depends on the control mode set in A1-02. For PM OLV Control the setting range is 0 to 2.
<51> Parameter value is changed if E2-11 is manually changed or changed by Auto-Tuning.
<56> The default value is 0 for all 200 V Single-Phase drives.
<57> Default setting value is dependent on parameter o2-04, Drive/kVA Selection and C6-01, Drive Duty Selection.

◆ n: Advanced Performance Set-Up

The n parameters are used to adjust more advanced performance characteristics such as
hunting prevention, speed feedback detection, high-slip braking and R1 online tuning.

Control
Mode
No. Name Description Range Def. Addr. Pg.
V/ O P Hex
L
f M
V
n1: Hunting Prevention
Use n1 parameters to configure hunting prevention operation.
If the motor vibrates while lightly loaded,
Hunting Prevention may reduce the vibration.
Hunting Prevention 0: Disabled
n1-01 0,1 1 A − − 580 —
Selection 1: Enabled
When quick response is needed disable
Hunting Prevention.
Sets the gain for the Hunting Prevention
Function.
If the motor vibrates while lightly loaded and
Hunting Prevention 0.00 to
n1-02 n1-01 = 1, increase the gain by 0.1 until 1.00 A − − 581 —
Gain Setting 2.50
vibration ceases.
If the motor stalls while n1-01 = 1, decrease
the gain by 0.1 until the stalling ceases.
Hunting Prevention Sets the time constant used for hunting <12
n1-03 0 to 500 A − − 582 —
Time Constant prevention. >
Sets the gain used for Hunting Prevention.
Hunting Prevention 0.00 to
n1-05 When set to 0, the gain n1-02 is used for 0.00 A − − 530 —
Gain while in Reverse 2.50
operation in reverse direction.

366 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 B.2 Parameter Table

Control
Mode
No. Name Description Range Def. Addr. Pg.
V/ O P Hex
f L M
V
n2: Speed Feedback Detection Control Function
Use n2 parameters to configure the Speed Feedback Detection Control function operation.
Sets the internal speed feedback detection 0.00 to
1.00 − A − 584 —
control gain in the automatic frequency 10.00
Speed Feedback regulator (AFR).
n2-01 Detection Control This parameter does not typically require
(AFR) Gain adjustment. Adjust this parameter as follows: Adjust the setting by 0.05 units at a
If hunting occurs, increase the set value. time, while checking the response.
If response is low, decrease the set value.
Speed Feedback
0 to 50
n2-02 Detection Control Sets the AFR time constant 1. − A − 585 —
2000 ms
(AFR) Time Constant
Speed Feedback Sets the AFR time constant 2. Increase the
Detection Control setting if overvoltage occurs during sudden 0 to 750
n2-03 − A − 586 —
(AFR) Time Constant load changes or the speed overshoots during 2000 ms
2 fast acceleration.
n3: High-Slip Braking
Use n3 parameters to configure the high-slip braking function.
Sets the output frequency reduction step width
High-Slip Braking when the drive stops the motor using high-slip
n3-01 Deceleration braking (HSB). 1 to 20 5% A − − 588 —
Frequency Width If Overvoltage (OV) faults occur during HSB,
this parameter may need to be increased.

Parameter List
Sets the current limit during HSB. Higher
High-Slip Braking n3-02 settings will shorten motor stopping 100 to 150
n3-02 A − − 589 —
Current Limit times but increase the motor current, and 200 %
therefore motor heating.
Sets the time the drive will run with minimum
frequency (E1-09) at the end of deceleration.
n3-03
High-Slip Braking
Dwell Time at Stop
If this time is set too low, the machine inertia
0.0 to
10.0
1.0 s A − − 58A — B
can cause the motor to rotate slightly after
HSB completion.
Sets the time required for an HSB overload
fault (OL7) to occur when the drive output
High-Slip Braking 30 to
n3-04 frequency does not change during an HSB 40 s A − − 58B —
Overload Time 1200
stop. This parameter does not typically require
adjustment.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 367
B.2 Parameter Table

Control
Mode
No. Name Description Range Def. Addr. Pg.
V/ O P Hex
f L M
V
Applies a gain to the V/f pattern during
deceleration (L3-04=4). Returns to normal
Overexcitation values after ramp to stop or at re-acceleration. 1.00 to
n3-13 1.10 A A − 531 —
Deceleration Gain To improve the braking power of 1.40
overexcitation, increase the gain by 1.25 to
1.30.
If overcurrent or overload occur during
High-Slip
high-slip deceleration, reduce the high-slip 100
n3-21 Suppression Current 0 to 150 A A − 579 —
suppression current level. Set as a percentage %
Level
of the drive rated current.
0: Disabled
Overexcitation
n3-23 1: Enabled only when rotating forward 0 to 2 0 A A − —
Operation Selection
2: Enabled only when in reverse
n6: Online Tuning of Resistance between Motor Lines
Use n6 parameters to adjust the motor line-to-line resistance while the drive is online.
Tunes the line-to-line motor resistance
Line-to-Line Motor
continuously during operation.
n6-01 Resistance Online 0,1 1 − A − 570 —
0: Disabled
Tuning
1: Enabled
n8: Permanent Magnet (PM) Motor Control
Use n8 parameters to control the PM motor control.
Sets the gain for internal speed feedback
Speed Feedback detection control. This parameter does not
0.0 to
n8-45 Detection Control typically require adjustment. 0.8 − − A 538 —
10.0
Gain Increase this setting if hunting occurs.
Decrease to lower the response.
Sets the time constant to make the pull-in
current and actual current value agree.
Pull-In Current
Decrease the value if the motor begins to 0.0 to
n8-47 Compensation Time 5.0 s − − A 53A —
oscillate. 100.0 s
Constant
Increase the value if it takes too long for the
current reference to equal the output current.
Defines the amount of current provided to the
motor during no load operation at a constant
speed. 20 to
n8-48 Pull-In Current 30% − − A 53B —
Set as a percentage of the motor rated current. 200%
Increase this setting when hunting occurs while
running at a constant speed.
Sets the amount of d-axis current when using -200.0
n8-49 Load Current 0% − − A 53C —
Energy Saving control. to 0.0%

368 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 B.2 Parameter Table

Control
Mode
No. Name Description Range Def. Addr. Pg.
V/ O P Hex
f L M
V
Sets the pull-in current during acceleration as a
Acceleration Pull-In percentage of the motor rated current (E5-03). 0 to
n8-51 50% − − A 53E —
Current Set to a high value when more starting torque 200%
is needed.
Sets the time constant for voltage error
compesation. Adjust the value when
• hunting occurs at low speed.
Voltage Error
• hunting occurs with sudden load changes. 0.00 to 1.00
n8-54 Compensation Time − − A 56D —
Increase in steps of 0.1 or disable the 10.00 s s
Constant
compensation by setting n8-45 to 0.
• oscillations occur ar start. Increase the value
in steps of 0.1.
Sets the ratio between motor and machine
inertia.
0: less than 1:10.
n8-55 Load Inertia 0 to 3 0 − − A 56E —
1: between 1:10 to 1:30.
2: between 1:30 to 1:50.
3: higher than 1:50.
Sets the limit for the output voltage.
n8-62 Adjustment is normally needed only if the 0.0 to 200
Output Voltage Limit - - A 57D —
<24> input voltage is below the n8-62 set value. In 230.0 Vac
this case set n8-62 to the input voltage.

<12> Default setting value is dependent on parameter o2-04, Drive/kVA Selection.

Parameter List
<24> Values shown here are for 200 V class drives. Double the value when using a 400 V class drive.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 369
B.2 Parameter Table

◆ o: Operator Related Parameters

o parameters are used to set up the LED digital operator displays.

Control
Mode
No. Name Description Range Def. O Addr. Pg.
V/ L P Hex
f M
V
o1: Display Settings
Use o1 parameters to configure the digital operator display.
Selects which monitor will be displayed in the 104 to
106 A A A 500 —
operation menu upon power-up when 621
o1-01 Drive Mode Unit o1-02 = 5. The monitor parameter number is
<22> Monitor Selection entered into the spaces provided: U†-††. Set to U1-06 as a default
For example, set “403” to display monitor —
(Output Voltage Reference).
parameter U4-03.
Selects the monitor to display upon power-up.
1: Frequency Reference (U1-01)
User Monitor
o1-02 2: Forward/Reverse
Selection After Power 1 to 5 1 A A A 501 —
<22> 3: Output Frequency (U1-02)
Up
4: Output Current (U1-03)
5: User Monitor (set by o1-01)
Sets the units to display the frequency
reference and output frequency.
0: Hz
Digital Operator
o1-03 1: % (100% = E1-04) 0 to 3 0 A A A 502 —
Display Selection
2: r/min (enter the number of motor poles into
E2-04/E4-04/E5-04)
3: User defined by parameters o1-10 and o1-11
Frequency Reference These settings define the display values when
1 to
o1-10 Setting and User-Set o1-03 is set to 3. <11> A A A 520 —
60000
Display o1-10 sets display values when operating at the
maximum output frequency.
o1-11 sets the position of the decimal
positions.

‫غغغغغغ‬
Frequency Reference
o1-11 Setting / Decimal o1-10: Sets the first five 0 to 3 <11> A A A 521 —
Display digits of the value,
disregarding the
decimal point.
o1-11: Sets the number
of digits past the
decimal point

370 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 B.2 Parameter Table

Control
Mode
No. Name Description Range Def. Addr. Pg.
V/ O P Hex
f L M
V
o2: Operator Keypad Functions
Use o2 parameters to configure LED digital operator key functions.
Enables/Disables the digital operator LOCAL/
LOCAL/REMOTE
REMOTE key.
o2-01 Key Function 0,1 1 A A A 505 —
0: Disabled
Selection
1: Enabled
Enables/Disables the operator panel STOP key
when the drive is operated form external
STOP Key Function
o2-02 sources (not operator). 0,1 1 A A A 506 —
Selection
0: Disabled
1: Enabled
Allows storing of parameter settings as a User
Initialization Selection (value 1110 for A1-03).
The value returns to 0 after entering 1 or 2.
User Parameter 0: No Change
o2-03 0 to 2 0 A A A 507 —
Default Value 1: Set Defaults - Saves current parameter
settings as user initialization.
2: Clear All - Clears the currently saved user
initialization.
Sets the kVA of the drive.
This parameter only needs to be set when
o2-04 Drive/kVA Selection 0 to FF <12> A A A 508 —
installing a new control board. Do not change
for other reason.

Parameter List
Selects if the ENTER key must be pressed
when inputting the frequency reference by the
operator keypad.
Frequency Reference
0: Data/Enter key must be pressed to enter a
o2-05 Setting Method 0,1 0 A A A 509 —
frequency reference.
Selection
1: Data/Enter key is not required. The
frequency reference is adjusted by the “up” and
“down” arrow keys. B
Sets drive action when the digital operator is
Operation Selection
removed in Local mode or with b1-02 = 0.
when Digital
o2-06 0: The drive will continue operation 0,1 0 A A A 50A —
Operator is
1: The drive will trigger a fault (OPR) and the
Disconnected
motor will coast to stop
0: Forward
Motor Direction at
1: Reverse
o2-07 Power Up when 0 to 1 0 A A A 527 —
This parameter requires that drive operation be
Using Operator
assigned to the digital operator.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 371
B.2 Parameter Table

Control
Mode
No. Name Description Range Def. Addr. Pg.
V/ O P Hex
f L M
V
o4: Maintenance Period
Use o4 parameters to perform maintenance.
Accumulated
Sets the starting value for the cumulative 0 to
o4-01 Operation Time 0 A A A 50B —
operation time of the drive in units of 10h. 9999
Setting
Sets this parameter to log the cumulative
Accumulated operation time (U4-01).
o4-02 Operation Time 0: Logs power-on time 0 to 1 0 A A A 50C —
Selection 1: Logs operation time when the drive output is
active (output operation time).
Cooling Fan
Used to resets the Cooling Fan operation time 0 to
o4-03 Operation Time 0 A A A 50E —
counter U1-04. 9999
Setting
Capacitor Resets the capacitor maintenance time monitor
o4-05 0 to 150 0% A A A 51D —
Maintenance Setting U4-05.
Inrush Prevention
Resets the Inrush Prevention Relay
o4-07 Relay Maintenance 0 to 150 0% A A A 523 —
Maintenance monitor U4-06.
Setting
IGBT Maintenance Resets the counter that logs the IGBTs usage
o4-09 0 to 150 0% A A A 525 —
Setting time. Refer to U4-07 (IGBT Maintenance).
Selects if U2-oo (Fault Trace) , U3-oo (Fault
History) monitors are reset at drive
U2, U3 Initialize
o4-11 initialization. 0 to 1 0 A A A 510 —
Selection
0: Saves the fault monitor data
1: Resets the fault monitor data
Selects if U4-10 and U4-11 (kWh monitor) are
kWh Monitor reset at drive initialization.
o4-12 0 to 1 0 A A A 512 —
Initialize Selection 0: Saves the U4-10 and U4-11 monitor data.
1: Resets the U4-10 and U4-11 monitor data.
Selects if the Run command counter (U4-02) is
Number of Run
reset at drive initialization.
o4-13 Commands Initialize 0 to 1 0 A A A 528 —
0: Saves the number of Run commands
Selection
1: Resets the number of Run commands

<9> Default setting value is dependent on parameter E1-01, Input Voltage Setting.
<11> Default setting value is dependent on parameter o1-03, Digital Operator Display Selection.
<12> Default setting value is dependent on parameter o2-04, Drive/kVA Selection.
<22> Parameter can be changed during run.

372 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 B.2 Parameter Table

◆ r: DWEZ Parameters
Control
Mode
No. Name Description Range Def. O Addr. Pg.
V/ P Hex
L
f V M

DWEZ Connection 0 to
r1-01 Parameter 1 for connecting DWEZ (upper). 0 – A A 1840 —
Parameter 1 (upper) FFFFH
DWEZ Connection 0 to
r1-02 Parameter 1 for connecting DWEZ (lower). 0 – A A 1841 —
Parameter 1 (lower) FFFFH
DWEZ Connection 0 to
r1-03 Parameter 2 for connecting DWEZ (upper). 0 – A A 1842 —
Parameter 2 (upper) FFFFH
DWEZ Connection 0 to
r1-04 Parameter 2 for connecting DWEZ (lower). 0 – A A 1843 —
Parameter 2 (lower) FFFFH
DWEZ Connection 0 to
r1-05 Parameter 3 for connecting DWEZ (upper). 0 – A A 1844 —
Parameter 3 (upper) FFFFH
DWEZ Connection 0 to
r1-06 Parameter 3 for connecting DWEZ (lower). 0 – A A 1845 —
Parameter 3 (lower) FFFFH
DWEZ Connection 0 to
r1-07 Parameter 4 for connecting DWEZ (upper). 0 – A A 1846 —
Parameter 4 (upper) FFFFH
DWEZ Connection 0 to
r1-08 Parameter 4 for connecting DWEZ (lower). 0 – A A 1847 —
Parameter 4 (lower) FFFFH
DWEZ Connection 0 to
r1-09 Parameter 5 for connecting DWEZ (upper). 0 – A A 1848 —
Parameter 5 (upper) FFFFH

Parameter List
DWEZ Connection 0 to
r1-10 Parameter 5 for connecting DWEZ (lower). 0 – A A 1849 —
Parameter 5 (lower) FFFFH
DWEZ Connection 0 to
r1-11 Parameter 6 for connecting DWEZ (upper). 0 – A A 184A —
Parameter 6 (upper) FFFFH
DWEZ Connection 0 to 184B
r1-12 Parameter 6 for connecting DWEZ (lower). 0 – A A —
Parameter 6 (lower) FFFFH H

r1-13
DWEZ Connection
Parameter 7 for connecting DWEZ (upper).
0 to
0 – A A 184C —
B
Parameter 7 (upper) FFFFH
DWEZ Connection 0 to
r1-14 Parameter 7 for connecting DWEZ (lower). 0 – A A 184D —
Parameter 7 (lower) FFFFH
DWEZ Connection 0 to
r1-15 Parameter 8 for connecting DWEZ (upper). 0 – A A 184E —
Parameter 8 (upper) FFFFH
DWEZ Connection 0 to
r1-16 Parameter 8 for connecting DWEZ (lower). 0 – A A 184F —
Parameter 8 (lower) FFFFH
DWEZ Connection 0 to
r1-17 Parameter 9 for connecting DWEZ (upper). 0 – A A 1850 —
Parameter 9 (upper) FFFFH
DWEZ Connection 0 to
r1-18 Parameter 9 for connecting DWEZ (lower). 0 – A A 1851 —
Parameter 9 (lower) FFFFH

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 373
B.2 Parameter Table

Control
Mode
No. Name Description Range Def. Addr. Pg.
V/ O P Hex
f L M
V
DWEZ Connection 0 to
r1-19 Parameter 10 for connecting DWEZ (upper). 0 – A A 1852 —
Parameter 10 (upper) FFFFH
DWEZ Connection 0 to
r1-20 Parameter 10 for connecting DWEZ (lower). 0 – A A 1853 —
Parameter 10 (lower) FFFFH
DWEZ Connection 0 to
r1-21 Parameter 11 for connecting DWEZ (upper). 0 – A A 1854 —
Parameter 11 (upper) FFFFH
DWEZ Connection 0 to
r1-22 Parameter 11 for connecting DWEZ (lower). 0 – A A 1855 —
Parameter 11 (lower) FFFFH
DWEZ Connection 0 to
r1-23 Parameter 12 for connecting DWEZ (upper). 0 – A A 1856 —
Parameter 12 (upper) FFFFH
DWEZ Connection 0 to
r1-24 Parameter 12 for connecting DWEZ (lower). 0 – A A 1857 —
Parameter 12 (lower) FFFFH
DWEZ Connection 0 to
r1-25 Parameter 13 for connecting DWEZ (upper). 0 – A A 1858 —
Parameter 13 (upper) FFFFH
DWEZ Connection 0 to
r1-26 Parameter 13 for connecting DWEZ (lower). 0 – A A 1859 —
Parameter 13 (lower) FFFFH
DWEZ Connection 0 to
r1-27 Parameter 14 for connecting DWEZ (upper). 0 – A A 185A —
Parameter 14 (upper) FFFFH
DWEZ Connection 0 to
r1-28 Parameter 14 for connecting DWEZ (lower). 0 – A A 185B —
Parameter 14 (lower) FFFFH
DWEZ Connection 0 to
r1-29 Parameter 15 for connecting DWEZ (upper). 0 – A A 185C —
Parameter 15 (upper) FFFFH
DWEZ Connection 0 to
r1-30 Parameter 15 for connecting DWEZ (lower). 0 – A A 185D —
Parameter 15 (lower) FFFFH
DWEZ Connection 0 to
r1-31 Parameter 16 for connecting DWEZ (upper). 0 – A A 185E —
Parameter 16 (upper) FFFFH
DWEZ Connection 0 to
r1-32 Parameter 16 for connecting DWEZ (lower). 0 – A A 185F —
Parameter 16 (lower) FFFFH
DWEZ Connection 0 to
r1-33 Parameter 17 for connecting DWEZ (upper). 0 – A A 1860 —
Parameter 17 (upper) FFFFH
DWEZ Connection 0 to
r1-34 Parameter 17 for connecting DWEZ (lower). 0 – A A 1861 —
Parameter 17 (lower) FFFFH
DWEZ Connection 0 to
r1-35 Parameter 18 for connecting DWEZ (upper). 0 – A A 1862 —
Parameter 18 (upper) FFFFH
DWEZ Connection 0 to
r1-36 Parameter 18 for connecting DWEZ (lower). 0 – A A 1863 —
Parameter 18 (lower) FFFFH
DWEZ Connection 0 to
r1-37 Parameter 19 for connecting DWEZ (upper). 0 – A A 1864 —
Parameter 19 (upper) FFFFH

374 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 B.2 Parameter Table

Control
Mode
No. Name Description Range Def. Addr. Pg.
V/ O P Hex
f L M
V
DWEZ Connection 0 to
r1-38 Parameter 19 for connecting DWEZ (lower). 0 – A A 1865 —
Parameter 19 (lower) FFFFH
DWEZ Connection 0 to
r1-39 Parameter 20 for connecting DWEZ (upper). 0 – A A 1866 —
Parameter 20 (upper) FFFFH
DWEZ Connection 0 to
r1-40 Parameter 20 for connecting DWEZ (lower). 0 – A A 1867 —
Parameter 20 (lower) FFFFH

◆ T: Motor Tuning
Enter data into the following parameters to tune the motor and drive for optimal
performance

Control
Mode
No. Name Description Range Def. O Addr. Pg.
V/ P Hex
L
f V M

Selects which set of motor parameters are used and

set during Auto-Tuning. If Motor 2 selection
(H1-†† = 16) is not selected, this parameter will
Motor
T1-00 not be displayed. 1, 2 1 A A − 700 —
Selection 1/2

Parameter List
1: 1st Motor - E1 to E2
2: 2nd Motor - E3 to E4 (this selection is not
displayed if motor 2 has not been selected)
Selects the Auto-Tuning mode. 2 or 3
0: Rotational Auto-Tuning in V/f
2: Stationary Auto-Tuning, Terminal resistance 0 or 2
Auto-Tuning 0, 2, 3
in OLV A A −
T1-01
Mode Selection
only,
3: Rotational Auto-Tuning for V/f control
<54>
2 for
701 —
B
(necessary for Energy Savings and Speed Motor
Estimation type speed search) 2
Sets the motor rated power in kilowatts (kW).
Motor Rated Note: If motor power is given in horsepower, 0.00 to 0.40
T1-02 A A − 702 —
Power power in kW can be calculated using the following 650.00 kW
formula: kW = HP x 0.746.
T1-03 Motor Rated 0.0 to 200.0
Sets the motor rated voltage in volts (V). A A − 703 —
<24> Voltage 255.5 V

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 375
B.2 Parameter Table

Control
Mode
No. Name Description Range Def. Addr. Pg.
V/ O P Hex
f L M
V
10 to
200% of
Motor Rated
T1-04 Sets the motor rated current in amperes (A). drive <12> A A − 704 —
Current
rated
current
Motor Base 0.0 to 60.0
T1-05 Sets the base frequency of the motor in Hertz (Hz). A A − 705 —
Frequency 400.0 Hz
Number of
T1-06 Sets the number of motor poles. 2 to 48 4 A A − 706 —
Motor Poles
Motor Base Sets the base speed of the motor in revolutions per 0 to 1750
T1-07 A A − 707 —
Speed minute r/min (RPM). 24000 r/min

Provides the iron loss for determining the Energy 14W A − − 70B —
Saving coefficient. The value set to E2-10 (motor These values differ
Motor Iron 0 to
T1-11 iron loss) when the power is cycled. If T1-02 is depending on the motor
Loss 65535
changed, an initial value valid for the selected code value and motor
capacity will be shown. parameter settings.

<12> Default setting value is dependent on parameter o2-04, Drive/kVA Selection.

<24> Values shown here are for 200 V class drives. Double the value when using a 400 V class drive.
<54> The available tuning methods dpend on control mode. Select values 2 or 3 in V/f control, 0 or 2 in OLV control,
and 2 for Motor 2 control.

◆ U: Monitors
Monitor parameters allow the user to view drive status, fault information, and other
information about drive operation.

Control
Analog Mode
No. Name Description Output Unit Addr.
V/ O
Level L P Hex
f V M

U1: Operation Status Monitors

Use U1 monitors to display the operation status of the drive.
10 V: Max 0.01
U1-01 Frequency Reference Monitors the frequency A A A 40
frequency Hz
0.01
Displays the output voltage. Display units are 10 V: Max Hz
U1-02 Output Frequency A A A 41
determined by o1-03. frequency <27
>

376 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 B.2 Parameter Table

Control
Analog Mode
No. Name Description Output Unit Addr.
Level V/ O P Hex
f L M
V
10 V: Drive 0.01
U1-03 Output Current Displays the output current. A A A 42
rated current A
Control method set in A1-02.
No output
0: V/f without PG
U1-04 Control Mode signal – A A A 43
2: Open Loop Vector (OLV)
available
5: PM Open Loop Vector (PM)
10 V:
Displays the motor speed feedback. 0.01
U1-05 Motor Speed Maximum – A A 44
Display units are determined by o1-03. Hz
speed
10 V: 200
Output Voltage 0.1
U1-06 Displays the output voltage. Vrms A A A 45
Reference V
(400 Vrms)
10 V: 400 V
U1-07 DC Bus Voltage Displays the DC bus voltage. 1V A A A 46
(800 V)
10 V:
Drive
capacity
Displays the output voltage (this value is <27
U1-08 Output Power (kW) A A A 47
determined internally). >
(max. motor
capacity
allowed)
Monitor of internal torque reference value for 10 V: Motor
U1-09 Torque Reference – – A –
Open Loop Vector (OLV) control rated torque

Parameter List
B

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 377
B.2 Parameter Table

Control
Analog Mode
No. Name Description Output Unit Addr.
Level V/ O P Hex
f L M
V
Displays the input terminal status.

U1-09=0 0 0 0 0 0 0
1: FWD run
command
(terminal S1
enabled)
1: REV run
command
(terminal S2
enabled)
1: Multi-Function
Digital
Input 1 (terminal
S3 enabled) No output
U1-10 Input Terminal Status 1: Multi-Function signal – A A A 49
Digital available
Input 2 (terminal
S4 enabled)
1: Multi-Function
Digital
Input 3 (terminal
S5 enabled)
1: Multi-Function
Digital
Input 4 (terminal
S6 enabled)
1: Multi-Function
Digital
Input 5 (terminal
S7 enabled)

Displays the output terminal status.

U1-11=0 0 0

1: Multi-Function
Digital Output (fault)
(terminal MA/MB-MC) No output
Output Terminal
U1-11 signal – A A A 4A
Status 1: Multi-Function available
Digital Output 1
(terminal P1) enabled
1: Multi-Function
Digital Output 2
(terminal P2) enabled

378 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 B.2 Parameter Table

Control
Analog Mode
No. Name Description Output Unit Addr.
Level V/ O P Hex
f L M
V
Verifies the drive operation status.

U1-12=0 0 0 0 0 0 0 0
1: During run
1: During
zero-speed
1: During REV
1: During fault
reset No output
U1-12 Drive Status signal input signal – A A A 4B
1: During speed available
agree
1: Drive ready

1: During alarm
detection
1: During fault
detection

Terminal A1 Input Displays the analog input A1 input level. 0.1

U1-13 10 V: 100% A A A 4E
Voltage 100% when the input is 10 V %

Parameter List
Terminal A2 Input Displays the analog input A2 input level. 0.1
U1-14 10 V: 100% A A A 4F
Voltage 100% when the input is 10 V / 20 mA %
Displays the output frequency including
Output Frequency 10 V: Max 0.01
U1-16 ramp times, S-curves. Units are determined A A A 53
after Soft Start frequency Hz
by o1-03.
Displays the parameter number for oPE No output
U1-18 OPE Fault Parameter or Err (operator error) where the error
occurred.
signal
available
– A A A 61 B

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 379
B.2 Parameter Table

Control
Analog Mode
No. Name Description Output Unit Addr.
Level V/ O P Hex
f L M
V
Displays the contents of a MEMOBUS/
Modbus error.

U1-18=0 0 0 0 0 0 0 0
1: CRC error
1: Data length
error
Not used
(normally 0) No output
MEMOBUS/Modbus
U1-19 1: Parity error signal – A A A 66
Error Code
available
1: Overrun error

1: Framing error

1: Timed out
Not used
(normally 0)

U1-24 Input Pulse Monitor Displays the Pulse Train input RP frequency. 32000 7D
No signal
U1-25 Software No. (Flash) Yaskawa Flash ID output 4D
available
No signal
U1-26 Software No. (ROM) Yaskawa ROM ID output 5B
available
U2: Fault Trace
Use U2 monitor parameters to view fault trace data.
No signal
U2-01 Current Fault Display of the current fault. – A A A 80
output avail.
No signal
U2-02 Previous Fault Display of the previous fault. – A A A 81
output avail.
Frequency Reference Displays the frequency reference at the No signal 0.01
U2-03 A A A 82
at Previous Fault previous fault. output avail. Hz
Output Frequency at Displays the output frequency at the previous No signal 0.01
U2-04 A A A 83
Previous Fault fault. output avail. Hz
Output Current at Displays the output current at the previous No signal
U2-05 A A A 84
Previous Fault fault. output avail.

380 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 B.2 Parameter Table

Control
Analog Mode
No. Name Description Output Unit Addr.
Level V/ O P Hex
f L M
V
Motor Speed at Displays the motor speed at the previous No signal 0.01
U2-06 − A − 85
Previous Fault fault. output avail. Hz
Output Voltage at Displays the output voltage at the previous No signal 0.1
U2-07 A A A 86
Previous Fault fault. output avail. V
DC Bus Voltage at Displays the DC bus voltage at the previous No signal
U2-08 1V A A A 87
Previous Fault fault. output avail.
Output Power at Displays the output power at the previous No signal 0.1
U2-09 A A A 88
Previous Fault fault. output avail. kW
Torque Reference at Displays the torque reference at the previous No signal 0.1
U2-10 − Α − 89
Previous Fault fault. output avail. %
Input Terminal Status Displays the input terminal status at the No signal
U2-11 – A A A 8A
at Previous Fault previous fault. Displayed as in U1-10. output avail.
Output Terminal Displays the output status at the previous No signal
U2-12 Status at Previous fault. Displays the same status displayed in output – A A A 8B
Fault U1-11. available
Drive Operation Displays the operation status of the drive at No signal
U2-13 Status at Previous the previous fault. Displays the same status output – A A A 8C
Fault displayed in U1-12. available
Cumulative Operation No signal
Displays the cumulative operation time at the
U2-14 Time at Previous output 1H A A A 8D
previous fault.
Fault available

Parameter List
Soft Starter Speed No signal
Displays the speed reference for the soft 0.01
U2-15 Reference at Previous output A A A 7E0
starter at the previous fault. %
Fault available
Motor q-Axis Current Displays the q-axis current for the motor at No signal 0.10
U2-16 − A A 7E1
at Previous Fault the previous fault. output avail. %
Motor d-Axis Current Displays the d-axis current for the motor at No signal 0.10
U2-17 − A A 7E2
at Previous Fault the previous fault.
U3: Fault History
output avail. %
B
Use U3 parameters to display fault data.
No signal 90
U3-01 Most Recent Fault Displays the most recent fault. – A A A
output avail. (800)
2nd Most Recent No signal 91
U3-02 Displays the second most recent fault. – A A A
Fault output avail. (801)
No signal 92
U3-03 3rd Most Recent Fault Displays the third most recent fault. – A A A
output avail. (802)
No signal
93
U3-04 4th Most Recent Fault Displays the fourth most recent fault. output – A A A
(803)
available

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 381
B.2 Parameter Table

Control
Analog Mode
No. Name Description Output Unit Addr.
Level V/ O P Hex
f L M
V
No signal
U3-05 5th Most Recent Fault Displays the fifth most recent fault. output – A A A 804
available
No signal
U3-06 6th Most Recent Fault Displays the sixth most recent fault. output – A A A 805
available
No signal
U3-07 7th Most Recent Fault Displays the seventh most recent fault. output – A A A 806
available
No signal
U3-08 8th Most Recent Fault Displays the eighth most recent fault. output – A A A 807
available
No signal
U3-09 9th Most Recent Fault Displays the ninth most recent fault. output – A A A 808
available
No signal
10th Most Recent
U3-10 Displays the tenth most recent fault. output – A A A 809
Fault
available
Cumulative Operation No signal
Displays the cumulative operation time at the 94
U3-11 Time at Most Recent output 1h A A A
most recent fault. (80A)
Fault available
Cumulative Operation No signal
Displays the cumulative operation time at the 95
U3-12 Time at 2nd Most output 1h A A A
second most recent fault. (80B)
Recent Fault available
Cumulative Operation No signal
Displays the cumulative operation time at the 96
U3-13 Time at 3rd Most output 1h A A A
third most recent fault. (80C)
Recent Fault available
Cumulative Operation No signal
Displays the cumulative operation time at the 97
U3-14 Time at 4th Most output 1h A A A
fourth most recent fault. (80D)
Recent Fault available
Cumulative Operation No signal
Displays the cumulative operation time at the
U3-15 Time at 5th Most output 1 h A A A 80E
fifth most recent fault.
Recent Fault available
Cumulative Operation No signal
Displays the cumulative operation time at the
U3-16 Time at 6th Most output 1h A A A 80F
sixth most recent fault.
Recent Fault available
Cumulative Operation No signal
Displays the cumulative operation time at the
U3-17 Time at 7th Most output 1 h A A A 810E
seventh most recent fault.
Recent Fault available

382 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 B.2 Parameter Table

Control
Analog Mode
No. Name Description Output Unit Addr.
Level V/ O P Hex
f L M
V
Cumulative Operation No signal
Displays the cumulative operation time at the
U3-18 Time at 8th Most output 1 h A A A 811E
eighth most recent fault.
Recent Fault available
Cumulative Operation No signal
Displays the cumulative operation time at the
U3-19 Time at 9th Most output 1h A A A 812
ninth most recent fault.
Recent Fault available
Cumulative Operation No signal
Displays the cumulative operation time at the
U3-20 Time at 10th Most output 1h A A A 813
tenth most recent fault.
Recent Fault available
U4: Maintenance Monitors
Use U4 parameters to display drive maintenance information.
Displays the cumulative operation time of the
drive. The value for the cumulative operation
time counter can be set in parameter o4-01.
Use parameter o4-02 to determine if the
Accumulated No signal
U4-01 operation time should start as soon as the 1h A A A 4C
Operation Time output avail.
power is switched on or only while the run
command is present. The maximum number
displayed is 99999, after which the value is
reset to 0.
Displays the number of times the run
command is entered. Reset the number of run
Number of Run No signal
U4-02 commands using parameter o4-13. This value A A A 76

Parameter List
Commands output avail.
will reset to 0 and start counting again after
reaching 65535.
Displays the cumulative operation time of the
cooling fan. The default value for the fan
Cooling Fan No signal
U4-03 operation time is set to parameter o4-03. This 1H A A A 67
Operation Time output avail.
value will reset to 0 and start counting again
after reaching 65535. B
Displays main circuit capacitor usage time in
Capacitor No signal
U4-05 in percent of their expected performance life. 1% A A A 7C
Maintenance output avail.
Parameter o4-06 resets this monitor.
Displays IGBT usage time as a percent of
expected performance life. One of the multi-
function contact outputs can be set to close
when the value reaches 50% (H2- = 2F),
No signal
U4-07 IGBT Maintenance triggering an alarm. One of the multi- 1% A A A 7D7
output avail.
function contact outputs can be set to close
when the value reaches 90% (H2- = 10),
triggering an alarm. Parameter o4-09 resets
this monitor.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 383
B.2 Parameter Table

Control
Analog Mode
No. Name Description Output Unit Addr.
Level V/ O P Hex
f L M
V
Lights all segments of the LED to verify that No signal
U4-09 LED Check – A A A 3C
the display is working properly. output avail.
U4-10 kWH, Lower 4 Digits Monitors the drive output power. The value is kWh A A A 5C
shown as a 9 digit number displayed across
two monitor parameters, U4-10 and U4-11.
Example: No signal
U4-11 kWH, Upper 5 Digits 12345678.9 kWh is displayed as: output avail. MW A A A 5D
U4-10: 678.9 kWh h
U4-11: 12345 MWh
Analog monitor: No output signal available.
10 V: Motor 0.01
U4-13 Peak Hold Current Displays the peak hold current during run. A A A 7CF
rated current A
Peak Hold Output Displays the output frequency when 10 V: Max 0.01
U4-14 A A A 7D0
Frequency operating at the peak hold current. frequency Hz
100% = OL1
Motor Overload 0.1
U4-16 100% = OL1 detection level detection A A A 7D8
Estimate (OL1) %
level
Displays the source for the frequency
reference as XY-nn.
X: indicates which reference is used:
1 = Reference 1 (b1-01)
2 = Reference 2 (b1-15)
Y-nn: indicates the reference source
0-01 = Operator (d1-01)
Frequency Reference
U4-18 1-01 = Analog (terminal A1) A A A 7DA
Source Selection
1-02 = Analog (terminal A2)
2-02 to 17 = Multi-step speed (d1-02 to 17)
3-01 = MEMOBUS/Modbus comm.
4-01 = Option
5-01 = Pulse Input
6-01 = CASE
7-01 = DWEZ
Frequency Reference
Displays the frequency reference provided by
U4-19 from MEMOBUS/ A A A 7DB
MEMOBUS/Modbus (decimal)
Modbus Comm.
Option Frequency Displays the frequency reference input by an
U4-20 A A A 7DD
Reference option card (decimal).

384 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 B.2 Parameter Table

Control
Analog Mode
No. Name Description Output Unit Addr.
Level V/ O P Hex
f L M
V
Displays the source for the Run command as
XY-nn.
X: Indicates which Run source is used:
1 = Reference 1 (b1-02)
2 = Reference 2 (b1-16)
Y: Input power supply data
0 = Operator
1 = External terminals
2 = Not used
3 = MEMOBUS/Modbus communications
4 = Option
5 = Not used
6 = CASE
7 = DWEZ
nn: Run command limit status data
00: No limit status.
Run Command
U4-21 01: Run command was left on when stopped A A A 7DD
Source Selection
in the PRG mode.
02: Run command was left on when
switching from local to remote operation.
03: Waiting for the soft charge bypass
contactor after the power is switched on (UV
or UV1 flashes after 10 seconds).
04: Waiting for “Run Command Prohibited”
time period to end.

Parameter List
05: Fast-stop (digital input (H1- = 15),
operator)
06: b1-17 (run command given at power-up).
07: During Baseblock while coast to stop
with timer
08: Frequency reference is below minimal
reference during base block
09: Waiting for Enter command B
Displays the drive control data set by
MEMOBUS/Modbus
MEMOBUS/Modbus communications
U4-22 Communications A A A 7DE
register No. 0001H as a 4 digit hexadecimal
Reference
number.
Option Card Displays drive control data set by an option
U4-23 A A A 7DF
Reference card as a 4 digit hexadecimal number.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 385
B.2 Parameter Table

Control
Analog Mode
No. Name Description Output Unit Addr.
Level V/ O P Hex
f L M
V
U5: Application Monitor
Use U5 parameters to view application-specific settings.
0.01
U5-01 PID Feedback Displays the PID feedback value in. A A A 57
%
Displays the amount of PID input (deviation 0.01
U5-02 PID Input A A A 63
between PID target and feedback). %
0.01
U5-03 PID Output Displays PID control output. A A A 64
%
10V: 100%
(max. freq.) 0.01
U5-04 PID Setpoint Displays the PID setpoint. A A A 65
%
PID differential Displays the 2nd PID feedback value if 0.01
U5-05 A A A
feedback differential feedback is used. %
Displays the subtraction value of both
PID Adjusted 0.01
U5-06 feedback values if differential feedback is A A A
Feedback %
used.
U6: Application Monitor
Use U6 parameters to display drive control information.
10 V: Motor
Motor Secondary Displays the value of the motor secondary rated 0.1
U6-01 A A A 51
Current (Iq) current (Iq). secondary %
current
10 V: Motor
Displays the value calculated for the motor
Motor Excitation rated 0.1
U6-02 excitation current (Id) as a percentage of the − A A 52
Current (ld) secondary %
motor rated secondary current (Iq).
current
Displays the ASR input value if Simple PG is 10V: 100% 0.1
U6-03 ASR Input A − −
used in V/f control. (max. freq.) %
Displays the ASR output value if Simple PG 10V: 100% 0.1
U6-04 ASR Output A − − 55
is used in V/f control. (max. freq.) %
Output voltage 10 V: 200 V 0.1
U6-05 Output voltage reference (Vq). (q-axis) − A A 59
reference (Vq) (400 V) Vac
Output Voltage 10 V: 200 V 0.1
U6-06 Output voltage reference (Vd). (d-axis) − A A 5A
Reference (Vd) (400 V) Vac
Displays the current control (ACR) output of 0.1
U6-07 q-axis ACR Output 10 V: 100% − A − 5F
for the motor secondary current (Iq). %
Displays the current control (ACR) output of 0.1
U6-08 d-Axis ACR Output 10 V: 100% − A − 60
for the motor excitation current (Id). %
Frequency Reference Displays the bias value used to adjust the 10 V: max. 0.1
U6-20 A A A 7D4
Bias (Up/Down 2) frequency reference. frequency %

386 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 B.2 Parameter Table

Control
Analog Mode
No. Name Description Output Unit Addr.
Level V/ O P Hex
f L M
V
Offset Displays the frequency added to the main 10 V: max. 0.1
U6-21 A A A 7D5
Frequency frequency reference. frequency %
U8: Custom Monitors for DriveWorksEZ
U8 parameters are reserved for DriveWorksEZ
0.01
U8-01 – Reserved for DriveWorksEZ, Monitor 1. – Α A Α 1950
%
0.01
U8-02 – Reserved for DriveWorksEZ, Monitor 2. – A A A 1951
%
0.01
U8-03 – Reserved for DriveWorksEZ, Monitor 3. – A A A 1952
%
0.01
U8-04 – Reserved for DriveWorksEZ, Monitor 4. – A A A 1953
%
0.01
U8-05 – Reserved for DriveWorksEZ, Monitor 5. – A A A 1954
%
0.01
U8-06 – Reserved for DriveWorksEZ, Monitor 6. – A A A 1955
%
0.01
U8-07 – Reserved for DriveWorksEZ, Monitor 7. – A A A 1956
%
0.01
U8-08 – Reserved for DriveWorksEZ, Monitor 8. – A A A 1957
%
0.01
U8-09 – Reserved for DriveWorksEZ, Monitor 9. – A A A 1958

Parameter List
%
0.01
U8-10 – Reserved for DriveWorksEZ, Monitor 10. – A A A 1959
%

<27> Setting units for this parameter are determined by o2-04, Drive/kVA Selection. Less than 11 kW: 2 decimal
points, 11 kW and above: 1 decimal point.

B
◆ Control Mode Dependent Parameter Default Values
The tables below list parameters that depend on the control mode selection (A1-02 for motor
1, E3-01 for motor 2). These parameters are initialized to the shown values if the control
mode is changed.
Table B.1 A1-02 (Motor 1 Control Mode) Dependent Parameters and Default Values

Control Modes (A1-02)

No. Description Setting Range Resolution
V/f (0) OLV (2) PM (5)
b3-02 Speed Search deactivation current 0 to 200 1% 120 100 –

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 387
B.2 Parameter Table

Control Modes (A1-02)

No. Description Setting Range Resolution
V/f (0) OLV (2) PM (5)
b8-02 Energy Saving gain 0.0 to 10.0 0.1 – 0.7 –
C2-01 S-curve time at acceleration start 0.00 to 10.00 0.01 s 0.20 0.20 1.00
C3-01 Slip compensation gain 0.0 to 2.5 0.1 0.0 1.0 –
C3-02 Slip compensation time constant 0 to 10000 1 msec 2000 200 –
C4-01 Torque comp. gain 0.00 to 2.50 0.01 1.00 1.00 0.00
C4-02 Torque comp. primary delay time 0 to 10000 1 msec 200 20 100
C6-02 Carrier frequency 1 to F 1 7 <12> 7 <12> 2
E1-04 Maximum output frequency 40.0 to 400.0 0.1 Hz 60.0 60.0 <10>
E1-05 Maximum output voltage <24> 0.0 to 255.0 0.1 V 230.0 230.0 <10>
E1-06 Base Frequency 0.0 to 400.0 0.1 Hz 60.0 60.0 <10>
E1-07 Middle output frequency 0.0 to 400.0 0.1 Hz 3.0 3.0 –
E1-08 Middle output freq. voltage <24> 0.0 to 255.0 0.1 V 18.4 13.8 –
E1-09 Minimum output frequency 0.0 to 400.0 0.1 Hz 1.5 0.5 <10>
E1-10 Minimum output voltage <24> 0.0 to 255.0 0.1 V 13.8 2.9 –
E1-11 Middle output frequency 2 0.0 to 400.0 0.1 Hz 0.0 0.0 –
E1-12 Middle output freq. voltage 2 <24> 0.0 to 255.0 0.1 V 0.0 0.0 –
E1-13 Base voltage <24> 0.0 to 255.0 0.1 V 0.0 0.0 –
L1-01 Motor protection selection 0 to 4 - 1 1 4
L3-20 Accel/Decel rate calculation rate 0.00 to 5.00 0.01 1.00 0.30 0.65
Decel time at stall prevention during
L3-21 0.00 to 200.00 0.01 1.00 1.00 2.50
acceleration

<10> Default setting value is dependent on parameter E5-01, Motor Code Selection.
<12> Default setting value is dependent on parameter o2-04, Drive/kVA Selection.
<24> Values shown here are for 200 V class drives. Double the value when using a 400 V class drive.

Table B.2 E3-01 (Motor 2 Control Mode) Dependent Parameters and Default Values

Control Modes (E3-01)

No. Description Setting Range Resolution
V/f (0) OLV (2)
E3-04 Maximum output frequency 40.0 to 400.0 0.1 Hz 60.0 60.0
E3-05 Maximum output voltage <24> 0.0 to 255.0 0.1 V 230.0 230.0
E3-06 Base Frequency 0.0 to 400.0 0.1Hz 60.0 60.0
E3-07 Middle output frequency 0.0 to 400.0 0.1Hz 3.0 3.0
E3-08 Middle output freq. voltage <24> 0.0 to 255.0 0.1 V 18.4 13.8
E3-09 Minimum output frequency 0.0 to 400.0 0.1 Hz 1.5 0.5
E3-10 Minimum output voltage <24> 0.0 to 255.0 0.1 V 13.8 2.9
E3-11 Middle output frequency 2 0.0 to 400.0 0.1 Hz 0.0 0.0

388 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 B.2 Parameter Table

Control Modes (E3-01)

No. Description Setting Range Resolution
V/f (0) OLV (2)
E3-12 Middle output freq. voltage 2 <24> 0.0 to 255.0 0.1 V 0.0 0.0
E3-13 Base voltage <24> 0.0 to 255.0 0.1 V 0.0 0.0
E3-14 Motor 2 Slip compensation gain 0.0 to 2.5 0.1 0.0 1.0

<24> Values shown here are for 200 V class drives. Double the value when using a 400 V class drive.

◆ V/f Pattern Default Values

The tables below show the V/f pattern settings default values depending on the control mode
(A1-02) and the V/f pattern selection (E1-03 in V/f control).
Table B.3 E1-03 V/f Pattern Settings for Drive Capacity: CIMR-VUBA0001 to CIMR-
VUBA0010; CIMR-VU2A0001 to CIMR-VU2A0010; CIMR-VU4A0001 to CIMR-VU4A0005

No. U V/f Control

<55 OLV
E1-03 − 0 1 2 3 4 5 6 7 8 9 A B C D E F >
50. 60. 60. 72. 50. 50. 60. 60. 50. 50. 60. 60. 90. 60.
E1-04 Hz 120 180 60.0 60.0
0 0 0 0 0 0 0 0 0 0 0 0 0 0
E1-05
V 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 230 230
<24>
50. 60. 50. 60. 50. 50. 60. 60. 50. 50. 60. 60. 60. 60. 60. 60.
E1-06 Hz 60.0 60.0
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
25. 25. 30. 30.

Parameter List
E1-07 Hz 2.5 3.0 3.0 3.0 2.5 2.5 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0
0 0 0 0
E1-08 16. 16. 16. 16. 35. 50. 35. 50. 19. 24. 19. 24. 16. 16. 16. 16.
V 18.4 13.8
<24> 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
E1-09 Hz 1.3 1.5 1.5 1.5 1.3 1.3 1.5 1.5 1.3 1.3 1.5 1.5 1.5 1.5 1.5 1.5 1.5 0.5
E1-10 12. 12. 12. 12. 12. 13. 12. 15. 12. 12. 12. 12.
V 8.0 9.0 8.0 9.0 13.8 2.9
<24> 0 0 0 0 0 0 0 0 0 0 0 0
B
<24> Values shown here are for 200 V class drives. Double the value when using a 400 V class drive.
<55> Used as default settings for E1-04 to E1-10 and E2-04 to E2-10

Table B.4 E1-03 V/f Pattern Settings for Drive Capacity: CIMR-VUBA0012 to CIMR-
VUBA0020; CIMR-VU2A0012 to CIMR-VU2A0069; CIMR-VU4A0007 to CIMR-VU4A0038

No. U V/f Control

<55 OLV
E1-03 − 0 1 2 3 4 5 6 7 8 9 A B C D E F
>
E1-04 Hz 50.0 60.0 60.0 72.0 50.0 50.0 60.0 60.0 50.0 50.0 60.0 60.0 90.0 120 180 60.0 60.0 60.0

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 389
B.2 Parameter Table

No. U V/f Control

<55 OLV
E1-03 − 0 1 2 3 4 5 6 7 8 9 A B C D E F >
E1-05
V 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 230 230
<24>
E1-06 Hz 50.0 60.0 50.0 60.0 50.0 50.0 60.0 60.0 50.0 50.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0
E1-07 Hz 2.5 3.0 3.0 3.0 25.0 25.0 30.0 30.0 2.5 2.5 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0
E1-08 14. 14. 14. 14. 35. 50. 35. 50. 18. 23. 18. 23. 14. 14. 14. 14.
V 16.1 12.7
<24> 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
E1-09 Hz 1.3 1.5 1.5 1.5 1.3 1.3 1.5 1.5 1.3 1.3 1.5 1.5 1.5 1.5 1.5 1.5 1.5 0.5
E1-10
V 7.0 7.0 7.0 7.0 6.0 7.0 6.0 7.0 9.0 11.0 9.0 13.0 7.0 7.0 7.0 7.0 8.1 2.3
<24>

<24> Vaaaaalues shown here are for 200 V class drives. Double the value when using a 400 V class drive.
<55> Used as default settings for E1-04 to E1-10 and E2-04 to E2-10

◆ Default Settings Determined by Drive Capacity (o2-04) and

ND/HD Selection (C6-01)
Default settings for the following parameters will vary based on drive capacity.
Table B.5 Single-Phase, 200 V Class Drives
Default Settings by Drive Capacity and ND/HD Settings

No. Description Unit Default Settings

− Model CIMR-Vo − BA0001 BA0002 BA0003
C6-01 Normal/Heavy Duty Sel. − HD ND HD ND HD ND
o2-04 kVA Selection − 48 (30H) 49 (31H) 50 (32H)
E2-11
(E4-11, Motor rated power kW 0.1 0.2 0.2 0.4 0.4 0.75
T1-02)
b3-06 Speed Search current 1 − 1 1 1 1 1 1
b8-04 Energy saving coefficient − 481.7 356.9 356.9 288.2 288.2 223.7
C6-02 Carrier frequency − 4 7 4 7 4 7
E2-01
(E4-01, Motor rated current A 0.6 1.1 1.1 1.9 1.9 3.3
T1-04)
E2-02
Motor rated slip Hz 2.5 2.6 2.6 2.9 2.9 2.5
(E4-02)
E2-03
Motor no load current A 0.4 0.8 0.8 1.2 1.2 1.8
(E4-03)
E2-05
Motor line-to-line resistance Ω 35.98 20.56 20.56 9.842 9.842 5.156
(E4-05)

390 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 B.2 Parameter Table

No. Description Unit Default Settings

− Model CIMR-Vo − BA0001 BA0002 BA0003
C6-01 Normal/Heavy Duty Sel. − HD ND HD ND HD ND
o2-04 kVA Selection − 48 (30H) 49 (31H) 50 (32H)
E2-11
(E4-11, Motor rated power kW 0.1 0.2 0.2 0.4 0.4 0.75
T1-02)
E2-06
Motor leakage inductance % 21.6 20.1 20.1 18.2 18.2 13.8
(E4-06)
E2-10
Motor Iron Loss W 6 11 11 14 14 26
(E4-10)
E5-01 Motor code hex FFFF FFFF FFFF FFFF 0002 0002
Momentary power loss ride-
L2-02 s 0.1 0.1 0.1 0.1 0.1 0.1
through time
Mom. power loss base block
L2-03 s 0.2 0.2 0.2 0.2 0.2 0.3
time
Momentary power loss voltage
L2-04 s 0.3 0.3 0.3 0.3 0.3 0.3
recovery time
L2-05 UV detection voltage V dc 160 160 160 160 160 160
L3-24 Motor acceleration time s 0.178 0.178 0.178 0.178 0.178 0.142
L8-02 Overheat alarm level ×C 115 115 115 115 110 110
L8-09 Ground fault selection − 0 0 0 0 0 0
L8-38 Carrier freq. reduction sel. − 1 1 1 1 1 1
n1-03 Hunting Prev. Time Const. ms 10 10 10 10 10 10

Parameter List
No. Description Unit Default Settings
− Model CIMR-Vo − BA0006 BA0010 BA0012 BA0018
C6-01 Normal/Heavy Duty − HD HD ND HD ND HD
−
o2-04
E2-11
kVA Selection 51 (33H) 52 (34H) 53 (35H) 55 (37H)
B
(E4-11, Motor rated power kW 0.75 1.1 1.5 2.2 2.2 3.0 3.7
T1-02)
b3-06 Speed Search current 1 − 0.5 0.5 0.5 0.5 0.5 0.5 0.5
b8-04 Energy saving coefficient − 223.7 169.4 169.4 156.8 156.8 136.4 122.9
C6-02 Carrier frequency − 4 7 3 7 3 7 3
E2-01
(E4-01, Motor rated current A 3.3 6.2 6.2 8.5 8.5 11.4 14.0
T1-04)
E2-02
Motor rated slip Hz 2.5 2.6 2.6 2.9 2.9 2.7 2.73
(E4-02)

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 391
B.2 Parameter Table

No. Description Unit Default Settings

− Model CIMR-Vo − BA0006 BA0010 BA0012 BA0018
C6-01 Normal/Heavy Duty − HD HD ND HD ND HD
o2-04 kVA Selection − 51 (33H) 52 (34H) 53 (35H) 55 (37H)
E2-11
(E4-11, Motor rated power kW 0.75 1.1 1.5 2.2 2.2 3.0 3.7
T1-02)
E2-03
Motor no load current A 1.8 2.8 2.8 3 3 3.7 4.5
(E4-03)
E2-05
Motor line-to-line resistance Ω 5.156 1.997 1.997 1.601 1.601 1.034 0.771
(E4-05)
E2-06
Motor leakage inductance % 13.8 18.5 18.5 18.4 18.4 19 19.6
(E4-06)
E2-10
Motor Iron Loss W 26 53 53 77 77 91 112
(E4-10)
E5-01 Motor Code hex 0003 0003 0005 0005 0006 0006 0008
Momentary power loss ride-
L2-02 s 0.2 0.2 0.3 0.3 0.5 0.5 1.0
through time
Momentary power loss base
L2-03 s 0.3 0.4 0.4 0.5 0.5 0.5 0.6
block time
Momentary power loss voltage
L2-04 s 0.3 0.3 0.3 0.3 0.3 0.3 0.3
recovery time
L2-05 UV detection voltage V dc 160 160 160 160 160 160 160
L3-24 Motor acceleration time s 0.142 0.142 0.166 0.145 0.145 0.145 0.154
L8-02 Overheat alarm level ×C 105 105 100 100 95 95 100
L8-09 Ground fault selection − 0 0 0 0 0 0 0
Carrier frequency reduction
L8-38 − 1 1 1 1 1 1 1
selection
Hunting Prevention Time
n1-03 ms 10 10 10 10 10 10 10
Constant

No. Description Unit Default Settings

− Model CIMR-VA − 2A0010 2A0012 2A0018 2A0020
C6-01 Normal/Heavy Duty − HD ND HD ND HD ND HD ND
o2-04 kVA Selection − 101 (65H) 102 (66H) 103 (67H) 104 (68H)
E2-11
(E4-11, Motor rated power kW 1.5 2.2 2.2 3.0 3.0 3.7 3.7 5.5
T1-02)
b3-06 Speed Search current 1 − 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5
b8-04 Energy saving coefficient − 169.4 156.8 156.8 136.4 136.4 122.9 122.9 94.75
C6-02 Carrier frequency − 3 7 3 7 3 7 3 7

392 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 B.2 Parameter Table

No. Description Unit Default Settings

− Model CIMR-VA − 2A0010 2A0012 2A0018 2A0020
C6-01 Normal/Heavy Duty − HD ND HD ND HD ND HD ND
o2-04 kVA Selection − 101 (65H) 102 (66H) 103 (67H) 104 (68H)
E2-11
(E4-11, Motor rated power kW 1.5 2.2 2.2 3.0 3.0 3.7 3.7 5.5
T1-02)
E2-01
(E4-01, Motor rated current A 6.2 8.5 8.5 11.4 11.4 14 14 19.6
T1-04)
E2-02
Motor rated slip Hz 2.6 2.9 2.9 2.7 2.7 2.73 2.73 1.5
(E4-02)
E2-03
Motor no load current A 2.8 3.0 3.0 3.7 3.7 4.5 4.5 5.1
(E4-03)
E2-05 Motor line-to-line
Ω 1.997 1.601 1.601 1.034 1.034 0.771 0.771 0.399
(E4-05) resistance
E2-06
Motor leakage inductance % 18.5 18.4 18.4 19 19 19.6 19.6 18.2
(E4-06)
E2-10
Motor Iron Loss W 53 77 77 91 91 112 112 172
(E4-10)
E5-01 Motor Code hex 0005 0005 0006 0006 FFFF FFFF 0008 0008
Momentary power loss
L2-02 s 0.3 0.3 0.5 0.5 1 1 1 1
ride-through time
Momentary power loss base
L2-03 s 0.4 0.5 0.5 0.5 0.5 0.6 0.6 0.7
block time

Parameter List
Momentary power loss
L2-04 s 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3
voltage recovery time
L2-05 UV detection voltage V dc 190 190 190 190 190 190 190 190
L3-24 Motor acceleration time s 0.166 0.145 0.145 0.145 0.145 0.154 0.154 0.168
L8-02 Overheat alarm level ×C 100 100 100 100 110 110 110 110
L8-09 Ground fault selection
Enclosure/Mounting
− 0 0 0 0 0 0 0 0
B
L8-35 − 0 0 0 0 0 0 0 0
selection
Carrier frequency reduction
L8-38 − 1 1 1 1 1 1 1 1
selection
Hunting Prevention Time
n1-03 ms 10 10 10 10 10 10 10 10
Constant

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 393
B.2 Parameter Table

No. Description Unit Default Settings

− Model CIMR-VA − 2A0030 2A0040 2A0056 2A0069
C6-01 Normal/Heavy Duty − HD ND HD ND HD ND HD ND
o2-04 kVA Selection − 106 (6AH) 108 (6CH) 109 (6DH) 110 (6EH)
E2-11
(E4-11, Motor rated power kW 5.5 7.5 7.5 11.0 11.0 15.0 15.0 18.5
T1-02)
b3-06 Speed Search current 1 − 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5
b8-04 Energy saving coefficient − 94.75 72.69 72.69 70.44 70.44 63.13 63.13 57.87
C6-02 Carrier frequency − 3 7 3 7 3 7 3 7
E2-01
(E4-01, Motor rated current A 19.6 26.6 26.6 39.7 39.7 53 53 65.8
T1-04)
E2-02
Motor rated slip Hz 1.5 1.3 1.3 1.7 1.7 1.6 1.6 1.67
(E4-02)
E2-03
(E4-03, Motor no load current A 5.1 8.0 8.0 11.2 11.2 15.2 15.2 15.7
T1-09)
E2-05 Motor line-to-line
Ω 0.399 0.288 0.288 0.230 0.230 0.138 0.138 0.101
(E4-05) resistance
E2-06
Motor leakage inductance % 18.2 15.5 15.5 19.5 19.5 17.2 17.2 15.7
(E4-06)
E2-10
Motor Iron Loss W 172 262 262 245 245 272 272 505
(E4-10)
E5-01 Motor Code hex FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFF
Momentary power loss
L2-02 s 1.0 1.0 1.0 1.0 2.0 2.0 2.0 2.0
ride-through time
Momentary power loss base
L2-03 s 0.7 0.8 0.8 0.9 0.9 1.0 1.0 1.0
block time
Momentary power loss
L2-04 s 0.3 0.3 0.3 0.3 0.3 0.3 0.6 0.6
voltage recovery time
L2-05 UV detection voltage V dc 190 190 190 190 190 190 190 190
L3-24 Motor acceleration time s 0.168 0.175 0.175 0.265 0.265 0.244 0.244 0.317
L8-02 Overheat alarm level ×C 115 115 121 121 120 120 120 120
L8-09 Ground fault selection − 1 1 1 1 1 1 1 1
Enclosure/Mounting
L8-35 − 2 2 2 2 2 2 2 2
selection
Carrier frequency reduction
L8-38 − 2 2 2 2 2 2 2 2
selection
Hunting Prevention Time
n1-03 ms 10 10 10 10 10 10 10 10
Constant

394 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 B.2 Parameter Table

Table B.6 Three-Phase, 200 V Class Drives

Default Settings by Drive Capacity and ND/HD Setting

No. Description Unit Default Settings

− Model CIMR-Vo − 2A0001 2A0002 2A0004 2A0006 2A0010
C6-01 Normal/Heavy Duty Sel. − HD ND HD ND HD ND HD ND HD ND
o2-04 kVA Selection − 96 (60H) 97 (61H) 98 (62H) 99 (63H) 101 (65H)
E2-11
(E4-11, Motor rated power kW 0.1 0.2 0.2 0.4 0.4 0.75 0.75 1.1 1.5 2.2
T1-02)
b3-06 Speed Search current 1 − 1.0 1.0 1.0 1.0 1.0 1.0 0.5 0.5 0.5 0.5
b8-04 Energy saving coefficient − 481.7 356.9 356.9 288.2 288.2 223.7 223.7 196.6 169.4 156.8
C6-02 Carrier frequency − 4 7 4 7 4 7 4 7 3 7
E2-01
(E4-01, Motor rated current A 0.6 1.1 1.1 1.9 1.9 3.3 3.3 4.9 6.2 8.5
T1-04)
E2-02
Motor rated slip Hz 2.5 2.6 2.6 2.9 2.9 2.5 2.5 2.6 2.6 2.9
(E4-02)
E2-03
Motor no load current A 0.4 0.8 0.8 1.2 1.2 1.8 1.8 2.3 2.8 3.0
(E4-03)
E2-05 Motor line-to-line
W 35.98 20.56 20.56 9.842 9.842 5.156 5.156 3.577 1.997 1.601
(E4-05) resistance
E2-06
Motor leakage inductance % 21.6 20.1 20.1 18.2 18.2 13.8 13.8 18.5 18.5 18.4
(E4-06)
E2-10 (
Motor Iron Loss W 6 11 11 14 14 26 26 38 53 77
E4-10)

Parameter List
E5-01 Motor Code hex FFFF FFFF FFFF FFFF 0002 0002 0003 0003 0005 0005
Momentary power loss
L2-02 s 0.1 0.1 0.1 0.1 0.1 0.1 0.2 0.2 0.3 0.3
ride-through time
Momentary power loss base
L2-03 s 0.2 0.2 0.2 0.2 0.2 0.3 0.3 0.4 0.4 0.5
block time

L2-04
Momentary power loss
s 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3
B
voltage recovery time
L2-05 UV detection voltage V dc 190 190 190 190 190 190 190 190 190 190
L3-24 Motor acceleration time s 0.178 0.178 0.178 0.178 0.178 0.142 0.142 0.142 0.166 0.145
L8-02 Overheat alarm level ×C 110 110 110 110 115 115 100 100 100 100
L8-09 Ground fault selection − 0 0 0 0 0 0 0 0 0 0
Carrier frequency reduction
L8-38 − 1 1 1 1 1 1 1 1 1 1
selection
Hunting Prevention Time
n1-03 ms 10 10 10 10 10 10 10 10 10 10
Constant

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 395
B.2 Parameter Table

No. Description Unit Default Settings

− Model CIMR-Vo − 2A0012 2A0020 2A0030
C6-01 Normal/Heavy Duty − HD ND HD ND HD ND
o2-04 kVA Selection − 102 (66H) 104 (68H) 106 (6AH)
E2-11
(E4-11, Motor rated power kW 2.2 3.0 3.7 5.5 5.5 7.5
T1-02)
b3-06 Speed Search current 1 − 0.5 0.5 0.5 0.5 0.5 0.5
b8-04 Energy saving coefficient − 156.8 136.4 122.9 94.75 94.75 72.69
C6-02 Carrier frequency − 3 7 3 7 3 7
E2-01
(E4-01, Motor rated current A 8.5 11.4 14 19.6 19.6 26.6
T1-04)
E2-02
Motor rated slip Hz 2.9 2.7 2.73 1.5 1.5 1.3
(E4-02)
E2-03
Motor no load current A 3.0 3.7 4.5 5.1 5.1 8.0
(E4-03)
E2-05 Motor line-to-line
Ω 1.601 1.034 0.771 0.399 0.399 0.288
(E4-05) resistance
E2-06
Motor leakage inductance % 18.4 19 19.6 18.2 18.2 15.5
(E4-06)
E2-10
Motor Iron Loss W 77 91 112 172 172 262
(E4-10)
E5-01 Motor Code hex 0006 0006 0008 0008 FFFF FFFF
Momentary power loss
L2-02 s 0.5 0.5 1 1 1.0 1.0
ride-through time
Momentary power loss base
L2-03 s 0.5 0.5 0.6 0.7 0.7 0.8
block time
Momentary power loss
L2-04 s 0.3 0.3 0.3 0.3 0.3 0.3
voltage recovery time
L2-05 UV detection voltage V dc 190 190 190 190 190 190
L3-24 Motor acceleration time s 0.145 0.145 0.154 0.168 0.168 0.175
L8-02 Overheat alarm level ×C 100 100 110 110 115 115
L8-09 Ground fault selection − 0 0 0 0 1 1
Carrier frequency reduction
L8-38 − 1 1 1 1 2 2
selection
Hunting Prevention Time
n1-03 ms 10 10 10 10 10 10
Constant

396 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 B.2 Parameter Table

No. Description Unit Default Settings

− Model CIMR-Vo − 2A0040 2A0056 2A0069
C6-01 Normal/Heavy Duty − HD ND HD ND HD ND
o2-04 kVA Selection − 108 (6CH) 109 (6DH) 110 (6EH)
E2-11
(E4-11, Motor rated power kW 7.5 11.0 11.0 15.0 15.0 18.5
T1-02)
b3-06 Speed Search current 1 − 0.5 0.5 0.5 0.5 0.5 0.5
b8-04 Energy saving coefficient − 72.69 70.44 70.44 63.13 63.13 57.87
C6-02 Carrier frequency − 3 7 3 7 3 7
E2-01
(E4-01, Motor rated current A 26.6 39.7 39.7 53 53 65.8
T1-04)
E2-02
Motor rated slip Hz 1.3 1.7 1.7 1.6 1.6 1.67
(E4-02)
E2-03
Motor no load current A 8.0 11.2 11.2 15.2 15.2 15.7
(E4-03)
E2-05 Motor line-to-line
Ω 0.288 0.230 0.230 0.138 0.138 0.101
(E4-05) resistance
E2-06
Motor leakage inductance % 15.5 19.5 19.5 17.2 17.2 15.7
(E4-06)
E2-10
Motor Iron Loss W 262 245 245 272 272 505
(E4-10)
E5-01 Motor Code hex FFFF FFFF FFFF FFFF FFFF FFFF

Parameter List
Momentary power loss
L2-02 s 1.0 1.0 2.0 2.0 2.0 2.0
ride-through time
Momentary power loss base
L2-03 s 0.8 0.9 0.9 1.0 1.0 1.0
block time
Momentary power loss
L2-04 s 0.3 0.3 0.3 0.3 0.6 0.6
voltage recovery time
L2-05 UV detection voltage V dc 190 190 190 190 190 190
B
L3-24 Motor acceleration time s 0.175 0.265 0.265 0.244 0.244 0.317
L8-02 Overheat alarm level ×C 121 121 120 120 120 120
L8-09 Ground fault selection − 1 1 1 1 1 1
Carrier frequency reduction
L8-38 − 2 2 2 2 2 2
selection
Hunting Prevention Time
n1-03 ms 10 10 10 10 10 10
Constant

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 397
B.2 Parameter Table

Table B.7 Three-Phase 400V Class Drives

Default Settings by Drive Capacity and ND/HD Setting

No. Description Unit Default Settings

− Model CIMR-Vo − 4A0001 4A0002 4A0004 4A0005
C6-01 Normal/Heavy Duty − HD ND HD ND HD ND HD ND
o2-04 kVA Selection − 145 (91H) 146 (92H) 147 (93H) 148 (94H)
E2-11
(E4-11, Motor rated power kW 0.2 0.4 0.4 0.75 0.75 1.5 1.5 2.2
T1-02)
b3-06 Speed Search current 1 − 1.0 1.0 0.5 0.5 0.5 0.5 0.5 0.5
b8-04 Energy saving coefficient − 713.8 576.4 576.4 447.4 447.4 338.8 338.8 313.6
C6-02 Carrier frequency − 3 7 3 7 3 7 3 7
E2-01
(E4-01, Motor rated current A 0.6 1 1 1.6 1.6 3.1 3.1 4.2
T1-04)
E2-02
Motor rated slip Hz 2.5 2.9 2.9 2.6 2.6 2.5 2.5 3
(E4-02)
E2-03
Motor no load current A 0.4 0.6 0.6 0.8 0.8 1.4 1.4 1.5
(E4-03)
E2-05 Motor line-to-line
Ω 83.94 38.198 38.198 22.459 22.459 10.1 10.1 6.495
(E4-05) resistance
E2-06
Motor leakage inductance % 21.9 18.2 18.2 14.3 14.3 18.3 18.3 18.7
(E4-06)
E2-10
Motor Iron Loss W 12 14 14 26 26 53 53 77
(E4-10)
E5-01 Motor Code hex FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFF
Momentary power loss
L2-02 s 0.1 0.1 0.1 0.1 0.2 0.2 0.3 0.3
ride-through time
Momentary power loss base
L2-03 s 0.2 0.2 0.2 0.3 0.3 0.4 0.4 0.5
block time
Momentary power loss
L2-04 s 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3
voltage recovery time
L2-05 UV detection voltage V dc 380 380 380 380 380 380 380 380
L3-24 Motor acceleration time s 0.178 0.178 0.178 0.142 0.142 0.166 0.166 0.145
L8-02 Overheat alarm level ×C 110 110 110 110 110 110 90 90
L8-09 Ground fault selection − 0 0 0 0 0 0 0 0
Carrier frequency reduction
L8-38 − 1 1 1 1 1 1 1 1
selection
Hunting Prevention Time
n1-03 ms 10 10 10 10 10 10 10 10
Constant

398 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 B.2 Parameter Table

No. Description Unit Setting Range

− Model CIMR-Vo − 4A0007 4A0009 4A0011 4A0018
C6-01 Normal/Heavy Duty Sel. − HD ND HD ND HD ND HD ND
o2-04 kVA Selection − 149 (95H) 150 (96H) 151 (97H) 153 (99H)
E2-11
(E4-11, Motor rated power kW 2.2 3.0 3.0 3.7 4.0 5.5 5.5 7.5
T1-02)
b3-06 Speed Search current 1 − 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5
b8-04 Energy saving coefficient − 313.6 265.7 265.7 245.8 245.8 189.5 189.5 145.38
C6-02 Carrier frequency − 3 7 3 7 3 7 3 7
E2-01
(E4-01, Motor rated current A 4.2 5.7 5.7 7 7 9.8 9.8 13.38
T1-04)
E2-02
Motor rated slip Hz 3 2.7 2.7 2.7 2.7 1.5 1.5 1.3
(E4-02)
E2-03
Motor no load current A 1.5 1.9 1.9 2.3 2.3 2.6 2.6 4.0
(E4-03)
E2-05 Motor line-to-line
Ω 6.495 4.360 4.360 3.333 3.333 1.595 1.595 1.152
(E4-05) resistance
E2-06
Motor leakage inductance % 18.7 19 19 19.3 19.3 18.2 18.2 15.5
(E4-06)
E2-10
Motor Iron Loss W 77 105 105 130 130 193 193 263
(E4-10)
E5-01 Motor Code hex FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFF

Parameter List
Momentary power loss
L2-02 s 0.5 0.5 0.5 0.5 0.5 0.5 0.8 0.8
ride-through time
Momentary power loss base
L2-03 s 0.5 0.5 0.5 0.6 0.6 0.7 0.7 0.8
block time
Momentary power loss
L2-04 s 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3
voltage recovery time
L2-05 UV detection voltage V dc 380 380 380 380 380 380 380 380
B
L3-24 Motor acceleration time s 0.145 0.145 0.145 0.154 0.154 0.154 0.168 0.175
L8-02 Overheat alarm level ×C 100 100 100 100 100 100 110 110
L8-09 Ground fault selection − 0 0 0 0 0 0 1 1
Carrier frequency reduction
L8-38 − 1 1 1 1 1 1 2 2
selection
Hunting Prevention Time
n1-03 ms 10 10 10 10 10 10 10 10
Constant

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 399
B.2 Parameter Table

No. Description Unit Setting Range

− Model CIMR-Vo − 4A0023 4A0031 4A0038
C6-01 Normal/Heavy Duty Sel. − HD ND HD ND HD ND
o2-04 kVA Selection − 154 (9AH) 156 (9CH) 157 (9DH)
E2-11
(E4-11, Motor rated power kW 7.5 11.0 11.0 15.0 15.0 18.5
T1-02)
b3-06 Speed Search current 1 − 0.5 0.5 0.5 0.5 0.5 0.5
b8-04 Energy saving coefficient − 145.38 140.88 140.88 126.26 126.26 115.74
C6-02 Carrier frequency − 3 7 3 7 3 7
E2-01
(E4-01, Motor rated current A 13.3 19.9 19.9 26.5 26.5 32.9
T1-04)
E2-02
Motor rated slip Hz 1.30 1.70 1.70 1.60 1.60 1.67
(E4-02)
E2-03
Motor no load current A 4.0 5.6 5.6 7.6 7.6 7.8
(E4-03)
E2-05 Motor line-to-line
Ω 1.152 0.922 0.922 0.550 0.550 0.403
(E4-05) resistance
E2-06
Motor leakage inductance % 15.5 19.6 19.6 17.2 17.2 20.1
(E4-06)
E2-10
Motor Iron Loss W 263 385 385 440 440 508
(E4-10)
E5-01 Motor Code hex FFFF FFFF FFFF FFFF FFFF FFFF
Momentary power loss
L2-02 s 1 1 2 2 2 2
ride-through time
Momentary power loss base
L2-03 s 0.8 0.9 0.9 1.0 1.0 1.0
block time
Momentary power loss
L2-04 s 0.3 0.3 0.3 0.6 0.6 0.6
voltage recovery time
L2-05 UV detection voltage V dc 380 380 380 380 380 380
L3-24 Motor acceleration time s 0.175 0.265 0.265 0.244 0.244 0.317
L8-02 Overheat alarm level ×C 110 110 110 110 110 110
L8-09 Ground fault selection − 1 1 1 1 1 1
Carrier frequency reduction
L8-38 − 2 2 2 2 2 2
selection
Hunting Prevention Time
n1-03 ms 10 10 10 10 10 10
Constant

400 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 B.2 Parameter Table

◆ Parameters that Change with the Motor Code Selection

The following tables show parameters and default settings that change with the motor code
selection E5-01 when Open Loop Vector for PM motors is used.
■ Yaskawa Pico Motor (SPM motor)
Table B.8 1800 rpm Type Yaskawa Pico Motor Settings

Par. Description Unit Default Settings

Motor Code − 0002 0003 0005 0006 0008
Voltage class 200 Vac 0.4 200 Vac 200 Vac 1.5 200 Vac 2.2 200 Vac 3.7
E5-01 −
Rated power kW 0.75 kW kW kW kW
Rated speed min-1 1800 1800 1800 1800 1800
E5-02 Motor rated power kW 0.4 0.75 1.5 2.2 3.7
E5-03 Motor rated current A 2.1 4.0 6.9 10.8 17.4
E5-04 Motor pole number – 8 8 8 8 8
E5-05 Motor winding resistance W 2.47 1.02 0.679 0.291 0.169
E5-06 d-axis inductance mH 12.7 4.8 3.9 3.6 2.5
E5-07 q-axis inductance mH 12.7 4.8 3.9 3.6 2.5
E5-09 Induction voltage constant 1 mVsec/rad 0 0 0 0 0
E5-24 Induction voltage constant 2 mV/min-1 62.0 64.1 73.4 69.6 72.2
E1-04 Maximum output frequency Hz 120 120 120 120 120
E1-05 Maximum output voltage V 200.0 200.0 200.0 200.0 200.0
E1-06 Base voltage Hz 120 120 120 120 120

Parameter List
E1-09 Minimum output voltage Hz 6 6 6 6 6
L3-24 Motor acceleration time s 0.064 0.066 0.049 0.051 0.044
n8-49 Pull-in current % 0 0 0 0 0

Table B.9 3600 rpm Type Yaskawa Pico Motor Settings

B
Par. Description Unit Default Settings
Motor Code − 0103 0105 0106 0108
Voltage class 200 Vac 200 Vac 200 Vac 200 Vac
E5-01 −
Rated power 0.75 kW 1.5 kW 2.2 kW 3.7 kW
Rated speed min-1 3600 3600 3600 3600
E5-02 Motor rated power kW 0.75 1.5 2.2 3.7
E5-03 Motor rated current A 4.1 8.0 10.5 16.5
E5-04 Motor pole number – 8 8 8 8
E5-05 Motor winding resistance W 0.538 0.20 0.15 0.097
E5-06 d-axis inductance mH 3.2 1.3 1.1 1.1

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 401
B.2 Parameter Table

Par. Description Unit Default Settings

E5-07 q-axis inductance mH 3.2 1.3 1.1 1.1
E5-09 Induction voltage constant 1 mVsec/rad 0 0 0 0
E5-24 Induction voltage constant 2 mV/min-1 32.4 32.7 36.7 39.7
E1-04 Maximum output frequency Hz 240 240 240 240
E1-05 Maximum output voltage V 200.0 200.0 200.0 200.0
E1-06 Base voltage Hz 240 240 240 240
E1-09 Minimum output voltage Hz 12 12 12 12
L3-24 Motor acceleration time s 0.064 0.066 0.049 0.051
n8-49 Pull-in current % 0 0 0 0

■ SS5 Motor: Yaskawa SSR1 Series IPM Motor

Table B.10 200 V, 1750 rpm Type Yaskawa SSR1 Series Motor

Par. Description Unit Default Settings

Motor Code − 1202 1203 1205 1206 1208
Voltage class 200 Vac 200 Vac 200 Vac 200 Vac 200 Vac
E5-01 −
Rated power 0.4 kW 0.75 kW 1.5 kW 2.2 kW 3.7 kW
Rated speed min-1 1750 1750 1750 1750 1750
E5-02 Motor rated power kW 0.4 0.75 1.5 2.2 3.7
E5-03 Motor rated current A 1.65 2.97 5.50 8.10 13.40
E5-04 Motor pole number – 6 6 6 6 6
E5-05 Motor winding resistance W 8.233 2.284 1.501 0.827 0.455
E5-06 d-axis inductance mH 54.84 23.02 17.08 8.61 7.20
E5-07 q-axis inductance mH 64.10 29.89 21.39 13.50 10.02
E5-09 Induction voltage constant 1 mVsec/rad 233.0 229.5 250.9 247.9 248.6
E5-24 Induction voltage constant 2 mV/min-1 0.0 0.0 0.0 0.0 0.0
E1-04 Maximum output frequency Hz 87.5 87.5 87.5 87.5 87.5
E1-05 Maximum output voltage V 190.0 190.0 190.0 190.0 190.0
E1-06 Base voltage Hz 87.5 87.5 87.5 87.5 87.5
E1-09 Minimum output voltage Hz 4.4 4.4 4.4 4.4 4.4
L3-24 Motor acceleration time s 0.092 0.076 0.051 0.066 0.075
n8-49 Pull-in current % –7.2 –10.8 –11.1 –17.8 –17.5

402 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 B.2 Parameter Table

Par. Description Unit Default Settings

Motor Code − 120A 120B 120D 120E
Voltage class 200 Vac 200 Vac 200 Vac 200 Vac
E5-01 −
Rated power 5.5 kW 7.5 kW 11 kW 15 kW
Rated speed min-1 1750 1750 1750 1750
E5-02 Motor rated power kW 5.5 7.5 11.0 15
E5-03 Motor rated current A 19.80 27.00 39.7 53.2
E5-04 Motor pole number – 6 6 6 6
E5-05 Motor winding resistance W 0.246 0.198 0.094 0.066
E5-06 d-axis inductance mH 4.86 4.15 3.40 2.65
E5-07 q-axis inductance mH 7.43 5.91 3.91 3.11
E5-09 Induction voltage constant 1 mVsec/rad 249.6 269.0 249.3 266.6
E5-24 Induction voltage constant 2 mV/min-1 0.0 0.0 0.0 0.0
E1-04 Maximum output frequency Hz 87.5 87.5 87.5 87.5
E1-05 Maximum output voltage V 190.0 190.0 190.0 190.0
E1-06 Base voltage Hz 87.5 87.5 87.5 87.5
E1-09 Minimum output voltage Hz 4.4 4.4 4.4 4.4
L3-24 Motor acceleration time s 0.083 0.077 0.084 0.102
n8-49 Pull-in current % –22.0 –17.3 –10.1 –10.3

Table B.11 400 V, 1750 rpm Type Yaskawa SSR1 Series Motor

Par. Description Unit Default Settings

Parameter List
Motor Code − 1232 1233 1235 1236 1238
Voltage class 400 Vac 400 Vac 400 Vac 400 Vac 400 Vac
E5-01 −
Rated power 0.4 kW 0.75 kW 1.5 kW 2.2 kW 3.7 kW
Rated speed min-1 1750 1750 1750 1750 1750
E5-02 Motor rated power kW 0.4 0.75 1.5 2.2 3.7
E5-03 Motor rated current A 0.83 1.49 2.75 4.05 6.80
B
E5-04 Motor pole number – 6 6 6 6 6
E5-05 Motor winding resistance W 32.932 9.136 6.004 3.297 1.798
E5-06 d-axis inductance mH 219.36 92.08 68.32 40.39 32.93
E5-07 q-axis inductance mH 256.40 119.56 85.56 48.82 37.70
E5-09 Induction voltage constant 1 mVsec/rad 466.0 459.0 501.8 485.7 498.7
E5-24 Induction voltage constant 2 mV/min-1 0.0 0.0 0.0 0.0 0.0
E1-04 Maximum output frequency Hz 87.5 87.5 87.5 87.5 87.5
E1-05 Maximum output voltage V 380.0 380.0 380.0 380.0 380.0
E1-06 Base voltage Hz 87.5 87.5 87.5 87.5 87.5

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 403
B.2 Parameter Table

Par. Description Unit Default Settings

E1-09 Minimum output voltage Hz 4.4 4.4 4.4 4.4 4.4
L3-24 Motor acceleration time s 0.092 0.076 0.051 0.066 0.075
n8-49 Pull-in current % –7.2 –10.7 –11.1 –8.9 –7.9

Par. Description Unit Default Settings

Motor Code − 123A 123B 123D 123E
Voltage class 400 Vac 400 Vac 400 Vac 400 Vac
E5-01 −
Rated power 5.5 kW 7.5 kW 11 kW 15 kW
Rated speed min-1 1750 1750 1750 1750
E5-02 Motor rated power kW 5.5 7.5 11.0 15
E5-03 Motor rated current A 9.90 13.10 19.9 26.4
E5-04 Motor pole number – 6 6 6 6
E5-05 Motor winding resistance W 0.982 0.786 0.368 0.263
E5-06 d-axis inductance mH 22.7 16.49 13.38 10.51
E5-07 q-axis inductance mH 26.80 23.46 16.99 12.77
E5-09 Induction voltage constant 1 mVsec/rad 498.0 541.7 508.7 531.9
E5-24 Induction voltage constant 2 mV/min-1 0.0 0.0 0.0 0.0
E1-04 Maximum output frequency Hz 87.5 87.5 87.5 87.5
E1-05 Maximum output voltage V 380.0 380.0 380.0 380.0
E1-06 Base voltage Hz 87.5 87.5 87.5 87.5
E1-09 Minimum output voltage Hz 4.4 4.4 4.4 4.4
L3-24 Motor acceleration time s 0.083 0.077 0.084 0.102
n8-49 Pull-in current % –10.2 –17.4 –15.8 –12.6

404 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 C
Network
Communications
This appendix details the specifications, connections, and
programming of the drive for MEMOBUS/Modbus
communication.

C.1 MEMOBUS/MODBUS BASIC SET-UP . . . . . . . . . . . . . . 406

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 405
C.1 MEMOBUS/Modbus Basic Set-Up

C.1 MEMOBUS/Modbus Basic Set-Up

Serial communication can be performed with Program Logic Controllers (PLCs) or similar
master devices using the MEMOBUS/Modbus protocol.

◆ MEMOBUS/Modbus Communication Configuration

MEMOBUS/Modbus communication is configured using 1 master (PLC) and a maximum
of 31 slaves. Serial communication between master and slave is normally initiated by the
master and responded to by the slaves.
The master performs serial communication with one slave at a time. Consequently, the slave
address of each slave must be initially set, so that the master can perform serial
communication using that address. Slaves receiving commands from the master perform the
specified functions, and send a response back to the master.
Figure C.1

Master

Slaves

AC Drive AC Drive AC Drive

Figure C.1 Example of Connections between Master and Drive

406 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 C.1 MEMOBUS/Modbus Basic Set-Up

◆ Communication Specifications
The MEMOBUS/Modbus communication specifications are explained in Table C.1.
Table C.1 MEMOBUS/Modbus Communication Specifications

Item Specifications
Interface RS-422, RS-485
Communications Cycle Asynchronous (Start-stop synchronization)
Baud rate: Select from 1200 to 115200 bps.
Data length: 8 bits fixed
Communications Parameters
Parity: Select from even, odd, or none.
Stop bits: 1 bit selected
Communications Protocol MEMOBUS/Modbus RTU
Number of Connectable Units 31 units maximum

◆ Communication Connection Terminal

MEMOBUS/Modbus communication uses the following terminals: S+, S-, R+, and R-. The
terminating resistor must be turned ON only if the Drive is at the very end of the serial
communication chain. Set the terminating resistor by turning ON pin 1 of switch S2.
Figure C.2

S+ +
-

Communications
S-
RS-422A
or RS-485 R+

Network
Switch
R- 1

Terminating resistor (1/2W, 110 Ohms)

C
Figure C.2 MEMOBUS/Modbus Switch
Table C.2 MEMOBUS/Modbus Switch Settings

S2 Position Description
ON Internal terminal resistance ON
OFF Internal terminal resistance OFF (no terminal resistance); default setting

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 407
C.1 MEMOBUS/Modbus Basic Set-Up

Figure C.3

A
B C

A – DIP switch S2 C – ON
B – OFF D –

Figure C.3 MEMOBUS/Modbus Terminals and Terminal Resistor Switch

Note: 1. Separate the communication cables from the main circuit cables and control circuit wiring.
2. Use shielded cables for the communication cable, and use proper shield clamps. Shield at one end only.
3. When using RS-485 communication, connect S+ to R+, and S- to R-, on the control circuit terminal
board. Refer to Figure C.4.

■ Serial Communication Terminals

Table C.3 Control Circuit Terminals: Serial Communications

Type No. Signal Name Function (Signal Level)

Default Setting

R+ Communications input (+)

MEMOBUS/Modbus RS-485/422
R– Communications input (–) communication: MEMOBUS/Modbus
MEMOBUS/Modbus Use a RS-485 or RS-422 communication protocol
S+ Communications output (+)
Communication cable to connect the drive. 115.2 kBps (max.)
S- Communications output (–)
IG Shield ground 0V

408 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 C.1 MEMOBUS/Modbus Basic Set-Up

Figure C.4

R+ R㧙 S+ S㧙 IG

P1 P2 PC A1 A2 +V AC AM AC MP

MA MB MC
S1 S2 S3 S4 S5 S6 S7 HC SC H1 RP

Figure C.4 Control Circuit Terminal Block Configuration

(CIMR-VA ; CIMR-VU )

Communications
◆ Communication Set-Up Procedure

Network
Use the following procedure to communicate with the PLC.
1. Turn OFF the input to the drive power and connect the communication cable

2.
between the PLC (or other master device) and the drive.
Turn ON the input power to the drive. C
3. Set the required communication parameters (H5-01 to H5-07) using the Digital
Operator.
4. Turn OFF the input to the drive power, and check that the Digital Operator display
has completely extinguished.
5. Turn ON the input power to the drive once again.
6. Perform communication with the master device.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 409
C.1 MEMOBUS/Modbus Basic Set-Up

Table C.4 Serial Communication Related Parameters

Parameter Name
Parameter Digital Operator Setting Factory
No. Description Range Setting
Display
Selects the frequency reference input source.
0: Operator - Digital preset speed U1-01 or d1-01 to d1-17.
Frequency 1: Terminals - Analog input terminal A1 (or terminal A2
Reference based on parameter H3-09).
b1-01 0 to 4 1
Selection 2: Serial Com - MEMOBUS/Modbus RS-422/485 terminals
Reference Source R+, R-, S+ and S-.
3: Option PCB
4: Pulse Input (Terminal RP)
Selects the run command input source.
0: Operator - RUN and STOP keys on the digital operator.
Run Command
1: Terminals - Contact closure on terminals S1 or S2.
b1-02 Selection 0 to 3 1
2: Serial Com - MEMOBUS/Modbus RS-422/485 terminals
Run Source
R+, R-, S+ and S-.
3: Option PCB.
Selects drive station node number (address) for MEMOBUS/
Drive Node Address 0 to 20
H5-01 Modbus terminals R+, R-, S+, S-. Cycle power for the 1F
Serial Comm Adr Hex
setting to take effect.
Selects the baud rate for MEMOBUS/Modbus terminals R+,
R-, S+ and S-. Cycle power for the setting to take effect.
0: 1200 bps
1: 2400 bps
Communication
2: 4800 bps
Speed
H5-02 3: 9600 bps 0 to 4 3
Selection
4: 19200 bps
Serial Baud Rate
5: 38400 bps
6: 57600 bps
7: 76800 bps
8: 115200 bps
Selects the communication parity for MEMOBUS/Modbus
Communication terminals R+, R-, S+ and
Parity S-. Cycle power for the setting to take effect.
H5-03 0 to 2 0
Selection 0: No parity
Serial Com Sel 1: Even parity
2: Odd parity
Selects the stopping method when a communication time-out
Stopping Method
fault (CE) is detected.
After
0: Ramp to stop
H5-04 Communication 0 to 3 3
1: Coast to stop
Error
2: Fast-stop
Serial Fault Sel
3: Alarm only

410 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 C.1 MEMOBUS/Modbus Basic Set-Up

Parameter Parameter Name Setting Factory

No. Digital Operator Description Range Setting
Display
Enables or disables the communications time-out fault (CE).
Communication
0: Disabled - A communication loss will not cause a
Fault
H5-05 communication fault. 0 to 10 1
Detection Selection
1: Enabled - If communication is lost for more than two
Serial Flt Dtct
seconds, a CE fault will occur.
Drive Transmit Wait
Set the delay time from when the drive receives data to when
H5-06 Time 5 to 65 5ms
the drive sends data.
Transmit WaitTIM
RTS Control Enables or disables "request to send" (RTS) control:
H5-07 Selection 0: Disabled - RTS is always on. 0 to 1 1
RTS Control Sel 1: Enabled - RTS turns on only when sending.

MEMOBUS/Modbus communication can perform the following operations regardless of the

settings in b1-01 and b1-02:
• Monitor the operation status of the drive
• Set and read drive parameters
• Reset faults
• Input multi-function digital input commands
• Control multi-function digital and analog outputs.

Note: An OR operation is performed between the multi-function command input from the master
device and the command input from multi-function digital input terminals S3 to S8.

Communications
Network
C

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 411
C.1 MEMOBUS/Modbus Basic Set-Up

412 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 D
Standards
Compliance
This chapter explains the guidelines and criteria for maintaining
CE and UL standards.

D.1 SECTION SAFETY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 414

D.2 EUROPEAN STANDARDS . . . . . . . . . . . . . . . . . . . . . . . 417
D.3 UL STANDARDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 425

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 413
D.1 Section Safety

D.1 Section Safety

DANGER
Electrical Shock Hazard
Do not connect or disconnect wiring while the power is on.
Failure to comply will result in death or serious injury.

WARNING
Electrical Shock Hazard
Do not operate equipment with covers removed.
Failure to comply could result in death or serious injury.
The diagrams in this section may show drives without covers or safety
shields to show details. Be sure to reinstall covers or shields before
operating the drives and run the drives according to the instructions
described in this manual.

Always ground the motor-side grounding terminal.

Improper equipment grounding could result in death or serious injury by
contacting the motor case.

Do not touch any terminals before the capacitors have fully

discharged.
Failure to comply could result in death or serious injury.
Before wiring terminals, disconnect all power to the equipment. The
internal capacitor remains charged even after the power supply is turned
off. The charge indicator LED will extinguish when the DC bus voltage is
below 50 Vdc. To prevent electric shock, wait at least five minutes after all
indicators are off and measure the DC bus voltage level to confirm safe
level.

414 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 D.1 Section Safety

WARNING
Do not allow unqualified personnel to perform work on the drive.
Failure to comply could result in death or serious injury.
Installation, maintenance, inspection, and servicing must be performed
only by authorized personnel familiar with installation, adjustment and
maintenance of AC drives.

Do not perform work on the drive while wearing loose clothing,

jewelry or without eye protection.
Failure to comply could result in death or serious injury.
Remove all metal objects such as watches and rings, secure loose clothing,
and wear eye protection before beginning work on the drive.

Do not remove covers or touch circuit boards while the power is on.
Failure to comply could result in death or serious injury.

WARNING
Fire Hazard
Tighten all terminal screws to the specified tightening torque.
Loose electrical connections could result in death or serious injury by fire

Standards Compliance
due to overheating of electrical connections.

Do not use an improper voltage source.

Failure to comply could result in death or serious injury by fire.
Verify that the rated voltage of the drive matches the voltage of the
incoming power supply before applying power.

Do not use improper combustible materials. D

Failure to comply could result in death or serious injury by fire.
Attach the drive to metal or other noncombustible material.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 415
D.1 Section Safety

NOTICE
Observe proper electrostatic discharge procedures (ESD) when
handling the drive and circuit boards.
Failure to comply may result in ESD damage to the drive circuitry.

Never connect or disconnect the motor from the drive while the drive
is outputting voltage.
Improper equipment sequencing could result in damage to the drive.

Do not use unshielded cable for control wiring.

Failure to comply may cause electrical interference resulting in poor
system performance. Use shielded twisted-pair wires and ground the shield
to the ground terminal of the drive.

Do not allow unqualified personnel to use the product.

Failure to comply could result in damage to the drive or braking circuit.
Carefully review instruction manual TOBPC72060000 when connecting a
braking option to the drive.

Do not modify the drive circuitry.

Failure to comply could result in damage to the drive and will void
warranty.
Yaskawa is not responsible for modification of the product made by the
user. This product must not be modified.

Check all the wiring to ensure that all connections are correct after
installing the drive and connecting other devices.
Failure to comply could result in damage to the drive.

416 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 D.2 European Standards

D.2 European Standards

Figure D.1

Figure D.1 CE Mark

The CE mark indicates compliance with European safety and environmental regulations and
is required for engaging in business and commerce in Europe.
European standards include the Machinery Directive for machine manufacturers, the Low
Voltage Directive for electronics manufacturers and the EMC guidelines for controlling
noise.
This drive displays the CE mark based on the EMC guidelines and the Low Voltage
Directive.
• EMC Guidelines: Devices used in combination with this drive must also be CE certified
and display the CE mark. When using drives displaying the CE mark in combination with
other devices, it is ultimately the responsibility of the user to ensure compliance with CE
standards. After setting up the device, verify that conditions meet European standards.
• Low Voltage Directive: 73/23/EEC, 93/68/EEC

◆ CE Low Voltage Directive Compliance

This drive has been tested according to European standard EN50178, and it fully complies
with the Low Voltage Directive.
To comply with the Low Voltage Directive, be sure to meet the following conditions when
combining this drive with other devices:

Standards Compliance
■ Area of Use
Do not use drives in areas with pollution higher than severity 2 and overvoltage category 3
in accordance with IEC664.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 417
D.2 European Standards

■ Installing Fuses on the Input Side

Install recommended UL-approved fuses at the main power input of the drive. Select fuses
according to Table D.1.
Table D.1 Recommended Input Fuse Selection

Time Delay/ Non-Time Delay/

Drive Model CIMR-V Class RK5 Fuses Fuse Ampere Rating Class T Fuses
600 Vac, 200 kAIR 600 Vac, 200 kAIR
200 V Class Single-Phase Drives
BA0001 TRS5R 5
BA0002 TRS10R 10
BA0003 TRS20R 20
Contact Yaskawa
BA0006 TRS35R 35
BA0010 TRS50R 50
BA0012 TRS60R 60
200 V Class Three-Phase Drives
2A0001 TRS5R 5
2A0002 TRS5R 5
2A0004 TRS10R 10
2A0006 TRS15R 15
2A0010 TRS25R 25 Contact Yaskawa
2A0012 TRS35R 35
2A0020 TRS60R 60
2A0030 70 A6T70
2A0040 100 A6T100
Not Available
2A0056 150 A6T150
2A0069 200 A6T200
400 V Class Three-Phase Drives
4A0001 TRS2.5R 2.5
4A0002 TRS5R 5
4A0004 TRS10R 10
4A0005 TRS20R 20 Contact Yaskawa
4A0007 TRS20R 20
4A0009 TRS20R 20
4A0011 TRS30R 30

418 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 D.2 European Standards

Time Delay/ Non-Time Delay/

Drive Model CIMR-V Class RK5 Fuses Fuse Ampere Rating Class T Fuses
600 Vac, 200 kAIR 600 Vac, 200 kAIR
4A0018 50 A6T50
4A0023 60 A6T60
Not Available
4A0031 70 A6T70
4A0038 80 A6T80

■ Guarding Against Harmful Materials

When installing IP20/Open-Chassis drives, use an enclosure that prevents foreign material
from entering the drive from above or below.
■ Grounding
The drive is designed to be used in T-N (grounded neutral point) networks. If installing the
drive in other types of grounded systems, contact your dealer or Yaskawa for instructions.

◆ EMC Guidelines Compliance

This drive is tested according to European standards EN61800-3 and it complies with the
EMC guidelines.
■ EMC Filter Installation
The following conditions must be met to ensure continued compliance with guidelines.
• EMC Filter Selection: Refer to Yaskawa catalog for EMC filter selection.
• EMC Filter Installation: Refer to option manual for option installation instructions.
Installation Method
Verify the following installation conditions to ensure that other devices and machinery used

Standards Compliance
in combination with this drive also comply with EMC guidelines.
1. Install an EMC noise filter to the input side specified by Yaskawa for compliance
with European standards.
2. Place the drive and EMC noise filter in the same enclosure.
3. Use braided shield cable for the drive and motor wiring or run the wiring through a
metal conduit.
4. Keep wiring as short as possible. Ground the shield on both the drive side and the
motor side.
D

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 419
D.2 European Standards

Figure D.2

A D C
U/T1 U
V/T2 V
M
W/T3 W

A – Drive D – Metal conduit

B – 20 m max cable length between E – Ground wire should be as short as
drive and motor possible.
C – Motor

Figure D.2 Installation Method

5. Ground the largest possible surface area of the shield to the metal conduit when
using braided shield cable. Yaskawa recommends using a cable clamp.
Figure D.3

C B

A – Braided shield cable C – Cable clamp (conductive)

B – Metal panel

Figure D.3 Ground Area

420 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 D.2 European Standards

Three-Phase 200 V / 400 V Class

Figure D.4

L3 A
L2

L1
PE
H

B
C
D

L3 L2 L1

J E
R/L1 S/L2 T/L3 U/T1 V/T2 W/T3

D
D
I

H F

Standards Compliance
A
G

A – Ground the cable shield F – Motor cable (braided shield cable,

max. 20 m)
B – Enclosure panel G – Motor
C – Metal plate H – Cable clamp
D – Grounding surface (remove any I – Max. distance between drive and
paint or sealant) noise filter D
E – Drive J – EMC noise filter

Figure D.4 EMC Filter and Drive Installation for CE Compliance

(Three-Phase 200 V / 400 V Class)

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 421
D.2 European Standards

Single-Phase 200 V Class

Figure D.5

A
L2

L1
PE

B
C
D

L3 L2 L1

J
E
R/L1 S/L2 T/L3 U/T1 V/T2 W/T3

D
D
I

H F

A
G

A – Ground the cable shield F – Motor cable (braided shield cable,

max. 20 m)
B – Enclosure panel G – Motor
C – Metal plate H – Cable clamp
D – Grounding surface (remove any I – Max. distance between drive and
paint or sealant) noise filter
E – Drive J – EMC noise filter

Figure D.5 EMC Filter and Drive Installation for CE Compliance

(Single-Phase 200 V Class)

422 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 D.2 European Standards

■ EMC Filters
The drive should be installed with the EMC filters listed below in order to comply with the
EN 61800-3, category C1 requirements.
Table D.2 EN 61800-3 Category C1 Filters

Filter Data (Manufacturer: Schaffner)

Drive Rated Drive Filter
CIMR-V† Weight Dimensions
Type Current
[kg] [W × L × H] Y×X Mounting Mounting
[A] Screw A Screw
200 V Single-Phase Units
BA0001 FS 5855-10/07 10 0.4 71 × 169 × 45 51 × 156 M4 M5
BA0002 FS 5855-10/07 10 0.4 71 × 169 × 45 51 × 156 M4 M5
BA0003 FS 5855-10/07 10 0.4 71 × 169 × 45 51 ×156 M4 M5
BA0006 FS 5855-20/07 20 0.7 111 × 169 × 50 91 × 156 M4 M5
BA0010 FS 5855-20/07 20 0.7 111 × 169 × 50 120 × 161 M4 M5
BA0012 FS 5855-30/07 30 1.0 144 × 174 × 50 120 × 161 M4 M5
200 V Three-Phase Units
2A0001 FS 5856-10-07 10 0.7 82 × 194 × 50 62 × 181 M4 M5
2A0002 FS 5856-10-07 10 0.7 82 × 194 × 50 62 × 181 M4 M5
2A0004 FS 5856-10-07 10 0.7 82 × 194 × 50 62 × 181 M4 M5
2A0006 FS 5856-10-07 10 0.7 82 × 194 × 50 62 × 181 M4 M5
2A0010 FS 5856-20-07 20 0.8 111 × 169 × 50 91 × 156 M4 M5
2A0012 FS 5856-20-07 20 0.8 111 × 169 × 50 91 × 156 M4 M5
2A0020 FS 5856-30-07 30 0.9 144 × 174 × 50 120 × 161 M4 M5

Standards Compliance
2A0030 FS 5973-35-07 35 1.4 141 × 330 × 46 115 × 313 M4 M5
2A0040 FS 5973-60-07 60 3.0 206 × 355 × 60 175 × 336 M5 M6
2A0056 FS 5973-60-07 60 3.0 206 × 355 × 60 175 × 336 M5 M6
2A0069 FS 5973-100-07 100 4.9 236 × 408 × 80 205 × 390 M8 M8
200 V Three-Phase Units
4A0001 FS 5857-5/07 5 0.5 111 × 169 × 45 91 × 156 M4 M5
4A0002 FS 5857-5/07 5 0.5 111 × 169 × 45 91 × 156 M4 M5
4A0004 FS 5857-10/07 10 0.75 111 × 169 × 45 91 × 156 M4 M5
D
4A0005 FS 5857-10/07 10 0.75 111 × 169 × 45 91 × 156 M4 M5
4A0007 FS 5857-10/07 10 0.75 111 × 169 × 45 91 × 156 M4 M5
4A0009 FS 5857-20/07 20 1.0 144 × 174 × 50 120 × 161 M4 M5
4A0011 FS 5857-20/07 20 1.0 144 × 174 × 50 120 × 161 M4 M5

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 423
D.2 European Standards

Filter Data (Manufacturer: Schaffner)

Drive Rated Drive Filter
CIMR-V† Type Current Weight Dimensions
Y×X Mounting Mounting
[kg] [W × L × H]
[A] Screw A Screw
4A0018 FS 5857-30-07 30 2.0 184 × 304 × 56 150 × 288 M4 M5
4A0023 FS 5857-30-07 30 2.0 184 × 304 × 56 150 × 288 M4 M5
4A0031 FS 5972-35-07 35 2.1 206 × 355 × 50 175 × 336 M4 M5
4A0038 FS 5972-60-07 60 4.0 236 × 408 × 65 390 × 205 M6 M6
Figure D.6

W H
Y

LINE
X
L

LOAD
A

PE

Figure D.6 EMC Filter Dimensions

■ DC Reactors
Table D.3 DC Reactors for Harmonics Reduction

Inverter Type DC Reactor

CIMR-Vo Model Rating
200V Three Phase Units
2A0004 5.4 A
UZDA-B
2A0006 8 mH
400 V Three Phase Units
4A0002 3.2 A
UZDA-B
4A0004 28 mH

Note: Contact Yaskawa for information about DC reactors for other models.

424 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 D.3 UL Standards

D.3 UL Standards
The UL/cUL mark applies to products in the United States and Canada indicates that UL has
performed product testing and evaluation and determined that their stringent standards for
product safety have been met. For a product to receive UL certification, all components
inside that product must also receive UL certification.
Figure D.7

C UL
R US
LISTED
Figure D.7 UL/cUL Mark

◆ UL Standards Compliance
This drive is tested in accordance with UL standard UL508C and complies with UL
requirements. The following conditions must be met to maintain compliance when using this
drive in combination with other equipment:
■ Installation Area
Do not install the drive to an area greater than pollution severity 2 (UL standard).
■ Main Circuit Terminal Wiring
Yaskawa recommends using UL-listed copper wires (rated at 75°C) and closed-loop
connectors or CSA-certified ring connectors sized for the selected wire gauge to maintain
proper clearances when wiring the drive. Use the correct crimp tool to install connectors per
manufacturer recommendation. Table D.4 lists a suitable closed-loop connector

Standards Compliance
manufactured by JST Corporation.
Table D.4 Closed-Loop Crimp Terminal Size (JIS C 2805)
(same for 200 V and 400 V)

Wire Gauge Terminal Crimp Terminal Tightening Torque

mm2 (AWG Screws Model Numbers N m (lb to in.)
0.75 M3.5 R1.25-3.5 0.8 to 1.0 (7.1 to 8.9)
(18) M4 R1.25-4 1.2 to 1.5 (10.6 to 13.3)
1.25 M3.5 R1.25-3.5 0.8 to 1.0 (7.1 to 8.9)
D
(16) M4 R1.25-4 1.2 to 1.5 (10.6 to 13.3)

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 425
D.3 UL Standards

Wire Gauge Terminal Crimp Terminal Tightening Torque

mm2 (AWG Screws Model Numbers N m (lb to in.)
M3.5 R2-3.5 0.8 to 1.0 (7.1 to 8.9)
2 M4 R2-4 1.2 to 1.5 (10.6 to 13.3)
(14) M5 R2-5 2.0 to 2.5 (17.7 to 22.1)
M6 R2-6 4.0 to 5.0 (35.4 to 44.3)
M4 R5.5-4 1.2 to 1.5 (10.6 to 13.3)
3.5/5.5 M5 R5.5-5 2.0 to 2.5 (17.7 to 22.1)
(12/10) M6 R5.5-6 4.0 to 5.0 (35.4 to 44.3)
M8 R5.5-8 9.0 to 11.0 (79.7 to 97.4)
M5 R8-5 2.0 to 2.5 (17.7 to 22.1)
8
M6 R8-6 4.0 to 5.0 (35.4 to 44.3)
(8)
M8 R8-8 9.0 to 11.0 (79.7 to 97.4)
M5 R14-5 2.0 to 2.5 (17.7 to 22.1)
14
M6 R14-6 4.0 to 5.0 (35.4 to 44.3)
(6)
M8 R14-8 9.0 to 11.0 (79.7 to 97.4)
22
M6 R22-6 4.0 to 5.0 (35.4 to 44.3)
(4)
M8 R22-8 9.0 to 11.0 (79.7 to 97.4)
30/38
M8 R38-8 9.0 to 11.0 (79.7 to 97.4)
(3/2)

<1> Use the specified crimp terminals (Model 14-NK5) when using CIMR-V 2A0030, V 2A0040, V 4A0023
with 14 mm2 (6 AWG).

Note: Use crimp insulated terminals or insulated shrink tubing for wiring connections. Wires should
have a continuous maximum allowable temperature of 75°C 600 Vac UL-approved vinyl-
sheathed insulation.
Table D.5 Recommended Input Fuse Selection

Time Delay/
Drive Model CIMR-V Class RK5 Fuses Fuse Ampere Rating
600 Vac, 200 kAIR
200 V Class Single-Phase Drives
BA0001 TRS5R 5
BA0002 TRS10R 10
BA0003 TRS20R 20
BA0006 TRS35R 35
BA0010 TRS50R 50
BA0012 TRS60R 60
200 V Class Three-Phase Drives
2A0001 TRS5R 5

426 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 D.3 UL Standards

Time Delay/
Drive Model CIMR-V Class RK5 Fuses Fuse Ampere Rating
600 Vac, 200 kAIR
2A0002 TRS5R 5
2A0004 TRS10R 10
2A0006 TRS15R 15
2A0010 TRS25R 25
2A0012 TRS35R 35
2A0020 TRS60R 60
2A0030 70
2A0040 100
Contact Yaskawa
2A0056 150
2A0069 200
400 V Class Three-Phase Drives
4A0001 TRS2.5R 2.5
4A0002 TRS5R 5
4A0004 TRS10R 10
4A0005 TRS20R 20
4A0007 TRS20R 20
4A0009 TRS20R 20
4A0011 TRS30R 30
4A0018 50
4A0023 60
Contact Yaskawa
4A0031 70
4A0038 80

Standards Compliance
■ Low Voltage Wiring for Control Circuit Terminals
Wire low voltage wires with NEC Class 1 circuit conductors. Refer to national state or local
codes for wiring. Use a class 2 (UL regulations) power supply for the control circuit
terminal.
Table D.6 Control Circuit Terminal Power Supply

Input / Output Terminal Signal Power Supply Specifications

Digital outputs P1*, P2*, PC*, MA, MB, MC, MP *Requires class 2 power supply. D
Use the internal power supply of the drive.
Digital inputs S1, S2, S3, S4, S5, S6, S7, SC, H1, HC
Use class 2 for external power supply.
Main frequency reference
Use the internal power supply of the drive.
(multi-function analog RP, +V, A1, A2, AC
Use class 2 for external power supply.
inputs)

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 427
D.3 UL Standards

■ Drive Short-Circuit Rating

This drive has undergone the UL short-circuit test, which certifies that during a short circuit
in the power supply the current flow will not rise above 30,000 amps maximum at 240 V for
200 V class drives and 480 V for 400 V class drives.
• The MCCB and breaker protection and fuse ratings shall be equal to or greater than the
short-circuit tolerance of the power supply being used.
• Suitable for use on a circuit capable of delivering not more than 30,000 RMS symmetrical
amperes for 240 V in 200 V class drives (up to 480 V for 400 V class drives) motor
overload protection.

◆ Drive Motor Overload Protection

Set parameter E2-01 (motor rated current) to the appropriate value to enable motor overload
protection. The internal motor overload protection is UL listed and in accordance with the
NEC and CEC.
■ E2-01 Motor Rated Current
Setting Range: Model Dependent
Factory Default: Model Dependent
Parameter E2-01 (motor rated current) protects the motor if parameter L1-01 is not set to 0
(default is 1, standard induction motor protection enabled).
If Auto-Tuning has been performed successfully, the motor data that was entered in T1-04 is
automatically written into parameter E2-01. If Auto-Tuning has not been performed,
manually enter the correct motor rated current in parameter E2-01.
■ L1-01 Motor Overload Protection Selection
The drive has an electronic overload protection function (OL1) based on time, output current
and output frequency, which protects the motor from overheating. The electronic thermal
overload function is UL-recognized, so it does not require an external thermal overload relay
for single motor operation.
This parameter selects the motor overload curve used according to the type of motor applied.

Table D.7 Overload Protection Settings

Setting Description
0 Disabled
1 Std Fan Cooled (< 10:1 motor) (factory default)
2 Standard Blower Cooled (10:1 motor)
3 Vector Motor (1000:1 motor)

428 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 D.3 UL Standards

Setting Description
4 PM motor

Disable the electronic overload protection (L1-01 = 0: Disabled) and wire each motor with
its own motor thermal overload when connecting the drive to more than one motor for
simultaneous operation.
Enable the motor overload protection (L1-01 = “1”, “2”, or “3”) when connecting the drive
to a single motor unless there is another means of preventing motor thermal overload. The
electronic thermal overload function causes an OL1 fault, which shuts off the output of the
drive and prevents additional overheating of the motor. The motor temperature is continually
calculated as long as the drive is powered up.
Setting L1-01 = 1 selects a motor with limited cooling capability below rated (base) speed
when running at 100% load. The OL1 function derates the motor when it is running below
base speed.
Setting L1-01 = 2 selects a motor capable of cooling itself over a 10:1 speed range when
running at 100% load. The OL1 function derates the motor when it is running at 1/10 or less
of its rated speed.
Setting L1-01 = 3 selects a motor capable of cooling itself at any speed — including zero
speed — when running at 100% load. The OL1 function does not derate the motor at any
speed.
Setting L1-01 = 4 selects protection for a PM motor.
■ L1-02 Motor Overload Protection Time
Setting Range: 0.1 to 20.0 Minutes
Factory Default: 8.0 Minutes
The L1-02 parameter sets the allowed operation time before the OL1 fault occurs when the

Standards Compliance
drive is running at 60 Hz and 133% of the full load amp rating (E2-01) of the motor.
Adjusting the value of L1-02 can shift the set of OL1 curves up the Y-axis of the diagram
below but will not change the shape of the curves.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 429
D.3 UL Standards

Figure D.8

10H z 60H z

10

8
1
6

E 2-01 125% 150% 175% 200%

A – Time (minutes) B – Output Current

(Percent of motor FLA)

Figure D.8 Motor Overload Protection Time

430 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 D.4 Safe Disable Input Precautions

D.4 Safe Disable Input Precautions

◆ Safe Disable Function Description

The Safe Disable function can be utilized to perform a safe stop following the EN60204-1,
stop category 0 (Uncontrolled stop by power removal). It is designed to meet the
requirements of the EN954-1, Safety Category 3 and EN61508, SIL2.
Removing the voltage from the terminal H1 activates the disables the drive output, i.e. the
power supply to the motor is cut by stopping the switching of the output transistors in a safe
way and “Hbb” is shown in the display. Safe Disable is applicable for induction and
permanent magnet motors.

◆ Installation
• If the Safe Disable function is utilized, the wire link between the terminals HC and H1,
which is preinstalled at the shipment, has to be removed entirely.
• Connect the drive to an EN954-1, Safety Category 3 interrupting device so that in case of
a safe stop request the connection between the terminals HC and H1 is opened.
Figure D.9

Power Supply
Drive
EN954-1 Safety
Cat, 3 Device

HC Controller

Standards Compliance
H1

Figure D.9 Safe Disable Wiring Example

Note: 1. To assure, that the Safe Disable function appropriately fulfills the safety requirements of the
application, a throughout risk assessment for the whole safety system has to be carried out.
D
2. The drive must be installed in a cabinet with a protection degree of at least IP54 in order to maintain
EN954-1, safety category 3 compliance.
3. If the safety device and the drive are installed in separate cabinets, the Safe Disable wires must be
installed in a short circuit proof way.
4. The Safe Disable function does not cut the power supply to the drive and does not provide electrical
isolation. Before any installation or maintenance work is done, the drives power supply must be
switched off.

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 431
D.4 Safe Disable Input Precautions

5. When PM motors are used, the following must be considered:

Even if the HWBB function is active, although unlikely a failure in two of the drives power devices can
occur which means that current flows through the motor winding. In an induction motor no torque can
be produced by that. However, if this happens and a PM motor is connected a torque is produced
causing an alignment of the rotor magnets. The rotor may turn up to 180 deg electrically. It must be
ensured, that this possible failure mode is not safety critical for the application.
6. The time from opening the the Safe Disable input until the drive output is switched off is less than 1 ms.

432 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 D.5 User Setting Table

D.5 User Setting Table

User User
No. Name Setting No. Name Setting
Motor Overheat Alarm Operation
A1-01 Access Level Selection L1-03
Selection (PTC input)
Motor Overheat Fault Operation
A1-02 Control Method Selection L1-04
Selection (PTC input)
Motor Temperature Input Filter Time
A1-03 Initialize Parameters L1-05
(PTC input)
Continuous Eletrothermal Operation
A1-04 Password 1 L1-13
Selection
Momentary Power Loss Operation
A1-05 Password 2 L2-01
Selection
Momentary Power Loss Ride-Thru
A1-06 Application Preset L2-02
Time
Momentary Power Loss Minimum
A1-07 DriveWorksEZ Function Selection L2-03
Baseblock Time
A2-01
Momentary Power Loss Voltage
to User Parameters, 1 to 32 L2-04
Recovery Ramp Time
A2-32
A2-33 User Parameter Automatic Selection L2-05 Undervoltage Detection Level (UV)
b1-01 Frequency Reference Selection 1 L2-06 KEB Deceleration Time
Momentary Power Loss Ride-Thru
b1-02 Run Command Selection 1 L2-07
Time
b1-03 Stopping Method Selection L2-08 Minimum Frequency Gain at KEB Start
b1-04 Reverse Operation Selection L2-11

Standards Compliance
b1-07 Local/Remote Run Selection L3-01 Stall Prevention Selection during Accel.
Run Command Selection while in
b1-08 L3-02 Stall Prevention Level during Accel.
Programming Mode
b1-14 Phase Order Selection L3-03 Stall Prevention Limit during Accel.
Stall Prevention Selection during
b1-15 Frequency Reference 2 L3-04
Deceleration
b1-16 Run Command Source 2 L3-05 Stall Prevention Selection during Run
b1-17 Run Command at Power Up L3-06 Stall Prevention Level during Run D
b2-01 DC Injection Braking Start Frequency L3-11 OV Suppression Function Selection
Overvoltage Suppression and
b2-02 DC Injection Braking Current L3-17 Deceleration Stall (Desired DC Bus
Voltage during Motor Stall)
DC Injection Braking Time/DC Main Power Circuit Voltage Adjustment
b2-03 L3-20
Excitation Time at Start Gain

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 433
D.5 User Setting Table

No. Name User No. Name User

Setting Setting
b2-04 DC Injection Braking Time at Stop L3-21 Accel/Decel Rate Calculation Gain
Deceleration Time at Stall Prevention
b2-08 Magnetic Flux Compensation Capacity L3-22
during Acceleration
Automatic Reduction Selection for Stall
b2-12 Short Circuit Brake Time at Start L3-23
Prevention during Run
Motor Acceleration Time for Inertia
b2-13 Short Circuit Brake Time at Stop L3-24
Calculations
b2-15 DC Injection Braking Current 2 L3-25 Load Inertia Ratio
b3-01 Speed Search Selection L4-01 Speed Agreement Detection Level
b3-02 Speed Search Deactivation Current L4-02 Speed Agreement Detection Width
b3-03 Speed Search Deceleration Time L4-03 Speed Agreement Detection Level (+/-)
b3-05 Speed Search Delay Time L4-04 Speed Agreement Detection Width (+/-)
Frequency Reference Loss Detection
b3-06 Output Current 1 during Speed Search L4-05
Selection
Speed Search Detection Compensation
b3-10 L4-06 Frequency Reference at Reference Loss
Gain
b3-14 Bi-Directional Speed Search Selection L4-07 Frequency Detection Conditions
b3-17 Speed Search Restart Current Level L5-01 Number of Auto Restart Attempts
b3-18 Speed Search Restart Detection Time L5-02 Auto Restart Operation Selection
b3-19 Number of Speed Search Restarts L5-04 Fault Reset Interval Time
b3-24 Speed Search Method Selection L5-05 Fault Reset Operation Selection
b3-25 Speed Search Retry Interval Time L6-01 Torque Detection Selection 1
b4-01 Timer Function On-Delay Time L6-02 Torque Detection Level 1
b4-02 Timer Function Off-Delay Time L6-03 Torque Detection Time 1
b5-01 PID Function Setting L6-04 Torque Detection Selection 2
b5-02 Proportional Gain Setting (P) L6-05 Torque Detection Level 2
b5-03 Integral Time Setting (I) L6-06 Torque Detection Time 2
Mechanical Weakening Detection
b5-04 Integral Limit Setting L6-08
Operation
Mechanical Weakening Detection
b5-05 Derivative Time L6-09
Speed Level
b5-06 PID Output Limit L6-10 Mechanical Weakening Detection Time
Mechanical Weakening Detection Start
b5-07 PID Offset Adjustment L6-11
Time
b5-08 PID Primary Delay Time Constant L7-01 Forward Torque Limit
b5-09 PID Output Level Selection L7-02 Reverse Torque Limit
b5-10 PID Output Gain Setting L7-03 Forward Regenerative Torque Limit
b5-11 PID Output Reverse Selection L7-04 Reverse Regenerative Torque Limit

434 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 D.5 User Setting Table

No. Name User No. Name User

Setting Setting
PID Feedback Reference Missing
b5-12 L7-06 Torque Limit Integral Time Constant
Detection Selection
Torque Limit Control Method Selection
b5-13 PID Feedback Loss Detection Level L7-07
during Accel/Decel
Internal Dynamic Braking Resistor
b5-14 PID Feedback Loss Detection Time L8-01
Protection Selection (ERF type)
b5-15 PID Sleep Function Start Level L8-02 Overheat Alarm Level
Overheat Pre-Alarm Operation
b5-16 PID Sleep Delay Time L8-03
Selection
b5-17 PID Accel/Decel Time L8-05 Input Phase Loss Protection Selection
b5-18 PID Setpoint Selection L8-07 Output Phase Loss Protection
Output Ground Fault Detection
b5-19 PID Setpoint Value L8-09
Selection
Heatsink Cooling Fan Operation
b5-20 PID Setpoint Scaling L8-10
Selection
Heatsink Cooling Fan Operation Delay
b5-34 PID Output Lower Limit L8-11
Time
b5-35 PID Input Limit L8-12 Ambient Temperature Setting
OL2 Characteristics Selection at Low
b5-36 PID Feedback High Detection Level L8-15
Speeds
PID Feedback High Level Detection
b5-37 L8-18 Soft CLA Selection
Time
Frequency Reduction Rate during OH
b5-38 PID Setpoint / User Display L8-19
Pre-Alarm
b5-39 PID Setpoint and Display Digits L8-29 Current Unbalance Detection (LF2)
b6-01 Dwell Reference at Start L8-35 Side-by-Side Selection

Standards Compliance
b6-02 Dwell Time at Start L8-38 Carrier Frequency Reduction
b6-03 Dwell Frequency at Stop L8-41 Current Alarm Selection
b6-04 Dwell Time at Stop n1-01 Hunting Prevention Selection
b8-01 Energy Saving Control Selection n1-02 Hunting Prevention Gain Setting
b8-02 Energy Saving Gain n1-03 Hunting Prevention Time Constant
Energy Saving Control Filter Time Hunting Prevention Gain while in
b8-03 n1-05
Constant Reverse

b8-04 Energy Saving Coefficient Value n2-01

Speed Feedback Detection Control D
(AFR) Gain
Speed Feedback Detection Control
b8-05 Power Detection Filter Time n2-02
(AFR) Time Constant
Speed Feedback Detection Control
b8-06 Search Operation Voltage Limit n2-03
(AFR) Time Constant 2

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 435
D.5 User Setting Table

No. Name User No. Name User

Setting Setting
High-Slip Braking Deceleration
C1-01 Acceleration Time 1 n3-01
Frequency Width
C1-02 Deceleration Time 1 n3-02 High-Slip Braking Current Limit
C1-03 Acceleration Time 2 n3-03 High-Slip Braking Dwell Time at Stop
C1-04 Deceleration Time 2 n3-04 High-Slip Braking Overload Time
Acceleration Time 3
C1-05 n3-13 Overexcitation Deceleration Gain
(Motor 2 Accel Time 1)
Deceleration Time 3
C1-06 n3-21 High-Slip Suppression Current Level
(Motor 2 Decel Time 1)
Acceleration Time 4
C1-07 n3-23 Overexcitation Operation Selection
(Motor 2 Accel Time 2)
Deceleration Time 4 Line-to-Line Motor Resistance Online
C1-08 n6-01
(Motor 2 Decel Time 2) Tuning
C1-09 Fast-Stop Time n8-45 Speed Feedback Detection Control Gain
Pull-In Current Compensation Time
C1-10 Accel/Decel Time Setting Units n8-47
Constant
C1-11 Accel/Decel Time Switching Frequency n8-48 Pull-In Current
C2-01 S-Curve Characteristic at Accel Start n8-49 Load Current
C2-02 S-Curve Characteristic at Accel End n8-50 Heavy Load Current Level (for PM)

C2-03 S-Curve Characteristic at Decel Start n8-51 Acceleration Time Pull-In Current

C2-04 S-Curve Characteristic at Decel End n8-55 Load Inertia

C3-01 Slip Compensation Gain n8-56 High Performance Control Selection
C3-02 Slip Compensation Primary Delay Time o1-01 Drive Mode Unit Monitor Selection
C3-03 Slip Compensation Limit o1-02 User Monitor Selection After Power Up
Slip Compensation Selection during
C3-04 o1-03 Digital Operator Display Selection
Regeneration
Output Voltage Limit Operation
C3-05 o1-05 LED Contrast
Selection
Frequency Reference Setting and User-
C4-01 Torque Compensation Gain o1-10
Set Display
Torque Compensation Primary Delay Frequency Reference Setting / Decimal
C4-02 o1-11
Time Display
LOCAL/REMOTE Key Function
C4-03 Torque Compensation at Forward Start o2-01
Selection
C4-04 Torque Compensation at Reverse Start o2-02 STOP Key Function Selection
C4-05 Torque Compensation Time Constant o2-03 User Parameter Default Value
Torque Compensation Primary Delay
C4-06 o2-04 Drive/kVA Selection
Time 2

436 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 D.5 User Setting Table

No. Name User No. Name User

Setting Setting
ASR Proportional Gain 1 Frequency Reference Setting Method
C5-01 o2-05
(for Simple PG V/f Control) Selection
ASR Integral Time 1 Operation Selection when Digital
C5-02 o2-06
(for Simple PG V/f Control) Operator is Disconnected
ASR Proportional Gain 2 Motor Direction at Power Up when
C5-03 o2-07
(for Simple PG V/f Control) Using Operator
ASR Integral Time 2
C5-04 o3-01 Copy Function Selection
(for Simple PG V/f Control)
C5-05 ASR Limit (for Simple PG V/f Control) o3-02 Copy Allowed Selection
C6-01 Duty Cycle o3-03 Copy Mode Selection
C6-02 Carrier Frequency Selection o4-01 Accumulated Operation Time Setting
C6-03 Carrier Frequency Upper Limit o4-02 Accumulated Operation Time Selection
Cooling Fan Maintenance Setting
C6-04 Carrier Frequency Lower Limit o4-03
(Operation Time)
C6-05 Carrier Frequency Proportional Gain o4-05 Capacitor Maintenance Setting
Inrush Prevention Relay Maintenance
d1-01 Frequency Reference 1 o4-07
Setting
d1-02 Frequency Reference 2 o4-09 IGBT Maintenance Setting
d1-03 Frequency Reference 3 o4-10 IGBT Maintenance Setting
d1-04 Frequency Reference 4 o4-11 U2, U3 Initial Value Selection
d1-05 Frequency Reference 5 o4-12 kWH Monitor Initial Value Selection
d1-06 Frequency Reference 6 o4-13 Motor r/min Reset
d1-07 Frequency Reference 7 r1-01 DWEZ Connection Parameter 1 (upr.)
d1-08 Frequency Reference 8 r1-02 DWEZ Connection Parameter 1 (lwr.)
d1-09 Frequency Reference 9 r1-03 DWEZ Connection Parameter 2 (upr.)

Standards Compliance
d1-10 Frequency Reference 10 r1-04 DWEZ Connection Parameter 2 (lwr.)
d1-11 Frequency Reference 11 r1-05 DWEZ Connection Parameter 3 (upr.)
d1-12 Frequency Reference 12 r1-06 DWEZ Connection Parameter 3 (lwr.)
d1-13 Frequency Reference 13 r1-07 DWEZ Connection Parameter 4 (upr.)
d1-14 Frequency Reference 14 r1-08 DWEZ Connection Parameter 4 (lwr.)
d1-15 Frequency Reference 15 r1-09 DWEZ Connection Parameter 5 (upr.)
d1-16 Frequency Reference 16 r1-10 DWEZ Connection Parameter 5 (lwr.)
d1-17 Jog Frequency Reference r1-11 DWEZ Connection Parameter 6 (upr.) D
d2-01 Frequency Reference Upper Limit r1-12 DWEZ Connection Parameter 6 (lwr.)
d2-02 Frequency Reference Lower Limit r1-13 DWEZ Connection Parameter 7 (upr.)
d2-03 Master Speed Reference Lower Limit r1-14 DWEZ Connection Parameter 7 (lwr.)
d3-01 Jump Frequency 1 r1-15 DWEZ Connection Parameter 8 (upr.)

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 437
D.5 User Setting Table

No. Name User No. Name User

Setting Setting
d3-02 Jump Frequency 2 r1-16 DWEZ Connection Parameter 8 (lwr.)
d3-03 Jump Frequency 3 r1-17 DWEZ Connection Parameter 9 (upr.)
d3-04 Jump Frequency Width r1-18 DWEZ Connection Parameter 9 (lwr.)
Frequency Reference Hold Function
d4-01 r1-19 DWEZ Connection Parameter 10 (upr.)
Selection
Frequency Reference Bias Step
d4-03 r1-20 DWEZ Connection Parameter 10 (lwr.)
(Up/Down 2)
Frequency Reference Accel/Decel
d4-04 r1-21 DWEZ Connection Parameter 11 (upr.)
(Up/Down 2)
Frequency Reference Bias Operation
d4-05 r1-22 DWEZ Connection Parameter 11 (lwr.)
Mode Selection (Up/Down 2)
d4-06 Frequency Reference Bias (Up/Down 2) r1-23 DWEZ Connection Parameter 12 (upr.)
Analog Frequency Reference
d4-07 r1-24 DWEZ Connection Parameter 12 (lwr.)
Fluctuation Limit (Up/Down 2)
Frequency Reference Bias Upper Limit
d4-08 r1-25 DWEZ Connection Parameter 13 (upr.)
(Up/Down 2)
Frequency Reference Bias Lower Limit
d4-09 r1-26 DWEZ Connection Parameter 13 (lwr.)
(Up/Down 2)
d7-01 Offset Frequency 1 r1-27 DWEZ Connection Parameter 14 (upr.)
d7-02 Offset Frequency 2 r1-28 DWEZ Connection Parameter 14 (lwr.)
d7-03 Offset Frequency 3 r1-29 DWEZ Connection Parameter 15 (upr.)
E1-01 Input Voltage Setting r1-30 DWEZ Connection Parameter 15 (lwr.)
E1-03 V/f Pattern Selection r1-31 DWEZ Connection Parameter 16 (upr.)
E1-04 Max Output Frequency (FMAX) r1-32 DWEZ Connection Parameter 16 (lwr.)
E1-05 Max Voltage (VMAX) r1-33 DWEZ Connection Parameter 17 (upr.)
E1-06 Base Frequency (FA) r1-34 DWEZ Connection Parameter 17 (lwr.)
E1-07 Mid Output Frequency (FB) r1-35 DWEZ Connection Parameter 18 (upr.)
E1-08 Mid Output Frequency Voltage (VC) r1-36 DWEZ Connection Parameter 18 (lwr.)
E1-09 Minimum Output Freq. (FMIN) r1-37 DWEZ Connection Parameter 19 (upr.)
E1-10 Minimum Output Freq.Voltage (VMIN) r1-38 DWEZ Connection Parameter 19 (lwr.)
E1-11 Mid Output Frequency 2 r1-39 DWEZ Connection Parameter 20 (upr.)
E1-12 Mid Output Frequency Voltage 2 r1-40 DWEZ Connection Parameter 20 (lwr.)
E1-13 Base Voltage (VBASE) T1-00 Motor Selection 1/2
E2-01 Motor Rated Current T1-01 Auto-Tuning Mode Selection
E2-02 Motor Rated Slip T1-02 Motor Rated Power
E2-03 Motor No-Load Current T1-03 Motor Rated Voltage
E2-04 Number of Motor Poles T1-04 Motor Rated Current

438 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 D.5 User Setting Table

No. Name User No. Name User

Setting Setting
E2-05 Motor Line-to-Line Resistance T1-05 Motor Base Frequency
E2-06 Motor Leakage Inductance T1-06 Number of Motor Poles
Motor Iron-Core Saturation Coefficient
E2-07 T1-07 Motor Base Speed
1
Motor Iron-Core Saturation Coefficient
E2-08 T1-11 Motor Iron Loss
2
E2-09 Motor Mechanical Loss U1-01 Frequency Reference
Motor Iron Loss for Torque
E2-10 U1-02 Output Frequency
Compensation
E2-11 Motor Rated Output U1-03 Output Current
Motor Iron-Core Saturation Coefficient
E2-12 U1-04 Control Mode
3
E3-01 Motor 2 Control Method Selection U1-05 Motor Speed

E3-04 Motor 2 Max Output Frequency U1-06 Output Voltage Reference

E3-05 Motor 2 Max Voltage (VMAX) U1-07 DC Bus Voltage

E3-06 Motor 2 Base Frequency (FA) U1-08 Output Power

E3-07 Motor 2 Mid Output Frequency (FB) U1-09 Torque Reference

Motor 2 Mid Output Frequency Voltage
E3-08 U1-10 Input Terminal Status
(VC)
E3-09 Motor 2 Minimum Output Freq.(FMIN) U1-11 Output Terminal Status
Motor 2 Minimum Output Freq. Voltage
E3-10 U1-12 Drive Status
(VMIN)
E3-11 Motor 2 Mid Output Freq. 2 U1-13 Terminal A1 Input Voltage

Standards Compliance
E3-12 Motor 2 Mid Output Freq. Voltage 2 U1-14 Terminal A2 Input Voltage

E3-13 Motor 2 Base Voltage (VBASE) U1-16 Output Frequency after Soft Start
E4-01 Motor 2 Rated Current U1-18 OPE Fault Parameter
E4-02 Motor 2 Rated Slip U1-19 MEMOBUS/Modbus Error Code
E4-03 Motor 2 Rated No-Load Current U1-24 Input Pulse Monitor
E4-04 Motor 2 Motor Poles U1-25 Software No. (Flash)
E4-05 Motor 2 Line-to-Line Resistance U1-26 Software No. (ROM) D
E4-06 Motor 2 Leakage Inductance U2-01 Current Fault
Motor 2 Motor Iron-Core Saturation
E4-07 U2-02 Previous Fault
Coefficient 1
Motor 2 Motor Iron-Core Saturation
E4-08 U2-03 Frequency Reference at Previous Fault
Coefficient 2

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 439
D.5 User Setting Table

No. Name User No. Name User

Setting Setting
E4-09 Motor 2 Mechanical Loss U2-04 Output Frequency at Previous Fault
E4-10 Motor 2 Iron Loss U2-05 Output Current at Previous Fault
E4-11 Motor 2 Rated Capacity U2-06 Motor Speed at Previous Fault
Motor 2 Iron-Core Saturation
E4-12 U2-07 Output Voltage at Previous Fault
Coefficient 3
E4-14 Motor 2 Slip Compensation Gain U2-08 DC Bus Voltage at Previous Fault
E4-15 Torque Compensation Gain - Motor 2 U2-09 Output Power at Previous Fault
E5-01 Motor Code Selection (PM motor) U2-10 Torque Reference at Previous Fault
E5-02 Motor Rated Capacity (PM motor) U2-11 Input Terminal Status at Previous Fault
Output Terminal Status at Previous
E5-03 Motor Rated Current (PM motor) U2-12
Fault
E5-04 Motor Poles (PM motor) U2-13 Drive Operation Status at Previous Fault
Cumulative Operation Time at Previous
E5-05 Motor Armature Resistance (PM motor) U2-14
Fault
Soft Starter Speed Reference at
E5-06 Motor d Axis Inductance (PM motor) U2-15
Previous Fault
E5-07 Motor q Axis Inductance (PM motor) U2-16 Motor q-Axis Current at Previous Fault
Motor Induction Voltage Constant 1
E5-09 U2-17 Motor d-Axis Current at Previous Fault
(PM motor)
Motor Induction Voltage Parameter 2
E5-24 U3-01 Most Recent Fault
(PM motor)
Operation Selection at PG Open Circuit
F1-02 U3-02 2nd Most Recent Fault
(PGO)
Operation Selection at Overspeed (OS)
F1-03 U3-03 3rd Most Recent Fault
(for Simple PG V/f)
Operation Selection at Deviation
F1-04 U3-04 4th Most Recent Fault
(for Simple PG V/f Control)
Overspeed Detection Level
F1-08 U3-05 5th Most Recent Fault
(for Simple PG V/f Control)
Overspeed Detection Delay Time
F1-09 U3-06 6th Most Recent Fault
(for Simple PG V/f Control)
Excessive Speed Deviation Detection
F1-10 U3-07 7th Most Recent Fault
Level (for Simple PG V/f Control)
Excessive Speed Deviation Detection
F1-11 Delay Time U3-08 8th Most Recent Fault
(for Simple PG V/f Control)
F1-14 PG Open-Circuit Detection Time
U3-09 9th Most Recent Fault
(for Simple PG V/f Control)

440 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 D.5 User Setting Table

No. Name User No. Name User

Setting Setting
F6-
01 to
Range reserved U3-10 10th Most Recent Fault
F6-
41
F7-
01 to Cumulative Operation Time at Most
Range reserved U3-11
F7- Recent Fault
21
Multi-Function Digital Input Terminal Cumulative Operation Time at 2nd
H1-01 U3-12
S1 Function Selection Most Recent Fault
Multi-Function Digital Input Terminal Cumulative Operation Time at 3rd Most
H1-02 U3-13
S2 Function Selection Recent Fault
Multi-Function Digital Input Terminal Cumulative Operation Time at 4th Most
H1-03 U3-14
S3 Function Selection Recent Fault
Multi-Function Digital Input Terminal Cumulative Operation Time at 5th Most
H1-04 U3-15
S4 Function Selection Recent Fault
Multi-Function Digital Input Terminal Cumulative Operation Time at 6th Most
H1-05 U3-16
S5 Function Selection Recent Fault
Multi-Function Digital Input Terminal Cumulative Operation Time at 7th Most
H1-06 U3-17
S6 Function Selection Recent Fault
Multi-Function Digital Input Terminal Cumulative Operation Time at 8th Most
H1-07 U3-18
S7 Function Selection Recent Fault
Terminal MA, MB and MC Function Cumulative Operation Time at 9th Most
H2-01 U3-19
Selection (relay) Recent Fault
Terminal P1 Function Selection Cumulative Operation Time at 10th
H2-02 U3-20
(open-collector) Most Recent Fault
Terminal P2 Function Selection
H2-03 U4-01 Accumulated Operation Time

Standards Compliance
(open-collector)
H2-06 Watt Hour Output Unit Selection U4-02 Number of Run Commands
H3-01 Terminal A1 Signal Level Selection U4-03 Cooling Fan Operation Time
H3-02 Terminal A1 Function Selection U4-05 Capacitor Maintenance
H3-03 Terminal A1 Gain Setting U4-07 IGBT Maintenance
H3-04 Terminal A1 Bias Setting U4-09 LED Check
H3-09 Terminal A2 Signal Level Selection U4-10 kWH, Lower 4 Digits
H3-10 Terminal A2 Function Selection
H3-11 Terminal A2 Gain Setting
U4-11 kWH, Upper 5 Digits
U4-13 Peak Hold Current
D
Frequency Reference (Current)
H3-12 U4-14 Peak Hold Output Frequency
Terminal A2 Input Bias
H3-13 Analog Input Filter Time Constant U4-16 Motor Overload Estimate (OL1)

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 441
D.5 User Setting Table

No. Name User No. Name User

Setting Setting
Multi-Function Analog 1
H4-01 U4-18 Frequency Reference Selection Results
(Terminal AM Monitor Selection)
Multi-Function Analog 1 Frequency Reference from
H4-02 U4-19
(Terminal AM Output Gain) MEMOBUS/Modbus Communications
Multi-Function Analog 1
H4-03 U4-20 Option Frequency Reference
(Terminal AM Output Bias)
H5-01 Drive Node Address U4-21 Run Command Selection Results
MEMOBUS/Modbus Communications
H5-02 Communication Speed Selection U4-22
Reference
H5-03 Communication Parity Selection U4-23 Option Card Reference
Stopping Method After Communication
H5-04 U5-01 PID Feedback
Error
Communication Fault Detection
H5-05 U5-02 PID Input (feedback)
Selection
H5-06 Drive Transmit Wait Time U5-03 PID Output
H5-07 RTS Control Selection U5-04 PID Setpoint
H5-09 CE Detection Time U6-01 Torque Reference (Internal)
Unit Selection for MEMOBUS/Modbus
H5-10 U6-02 Motor Secondary Current (Iq)
Register 0025H
Communications ENTER Function
H5-11 U6-03 Motor Excitation Current (ld)
Selection
Output of speed control (ASR)
H5-12 Run Command Method Selection U6-04
(for Simple V/f PG)
(Terminal RP) Pulse Train Input
H6-01 U6-05 Output voltage reference (Vq)
Function Selection
H6-02 Pulse Train Input Scaling U6-06 Output Voltage Reference (Vd)
H6-03 Pulse Train Input Gain U6-07 q-axis ACR Output
H6-04 Pulse Train Input Bias U6-08 d-Axis ACR Output
Energy Savings Coefficient Calculation
H6-05 Pulse Train Input Filter Time U6-17
Value
(Terminal MP) Pulse Train Monitor
H6-06 U6-18 PID Differential Feedback
Selection
H6-07 Pulse Train Monitor Scaling U6-19 PID Adjusted Feedback
L1-01 Motor Overload Protection Selection U6-20 Frequency Reference Bias (Up/Down 2)
L1-02 Motor Overload Protection Time U6-21 Offset Frequency

442 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
 A2-01 to A2-32 . . . . . . . . . . . . . . . . . . . 312, 433
A2-32. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165
A2-33. . . . . . . . . . . . . . . . . . 113, 165, 312, 433

Index Accel/Decel . . . . . . . . . . . . . . . . . . . . . . 132, 133

Accel/Decel Ramp Hold . . . . . . . . . . . . . . . . 342
Accel/Decel Time . . . . . . . . . . . . . . . . . . . . . 180
Accel/Decel Time 1 . . . . . . . . . . . . . . . . . . . . 342
Symbols Accel/Decel Time Selection 2 . . . . . . . . . . . . 342
Accel/Decel Time Setting Units . . . . . . 321, 436
(Terminal MP) Pulse Train Monitor Selection351,
Accel/Decel Time Switching Frequency 321, 436
442
(Terminal RP) Pulse Train Input Function Acceleration Error . . . . . . . . . . . . . . . . . 186, 223
Acceleration Time 1 . . . . . . . . . . .132, 320, 436
Selection . . . . . . . . . . . . . . . . . . . . . . . . .351, 442
Acceleration Time 2 . . . . . . . . . . . . . . . 320, 436
Numerics Acceleration Time 3 (Motor 2 Accel Time 1)320,
10th Most Recent Fault . . . . . . . . 150, 382, 441 436
2nd Most Recent Fault . . . . . . . . . 152, 381, 440 Acceleration Time 4 . . . . . . . . . . . . . . . 320, 436
2-Wire Initialization . . . . . . . . . . . . . . . . . . . . 122 Acceleration Time Pull-In Current . . . . 369, 436
2-Wire Sequence. . . . . . . . . . . . . . . . . . . . . . . 128 Acceleration/Deceleration . . . . . . . . . . . 132, 134
3rd Most Recent Fault . . . . . . . . . 152, 381, 440 Access Level Selection . . . . . . . . . . . . . 164, 311
3-Wire Initialization . . . . . . . . . . . . . . . . . . . . 123 Accumulated Operation Time . . . .151, 383, 441
3-Wire Sequence. . . . . . . . . . . . . . 128, 129, 341 Accumulated Operation Time Selection 372, 437
3-Wire Sequence Example . . . . . . . . . . . . . . . . 57 Accumulated Operation Time Setting . . 372, 437
4th Most Recent Fault . . . . . . . . . 152, 381, 440 Adjusting the Monitor Output . . . . . . . . . . . . 146
5th Most Recent Fault . . . . . . . . . 152, 382, 440 Speed Feedback Detection Control . . . . . . . . 237
6th Most Recent Fault . . . . . . . . . 152, 382, 440 AFR Gain . . . . . . . . . . . . . . . . . . . . . . . . . . . 178
7th Most Recent Fault . . . . . . . . . 152, 382, 440 AFR Time Constant 1 . . . . . . . . . . . . . . . . . . 178
8th Most Recent Fault . . . . . . . . . 152, 382, 440 AFR Time Constant 2 . . . . . . . . . . . . . . . . . . 178
9th Most Recent Fault . . . . . . . . . 152, 382, 440 Alarm. . . . . . . . . . . . . . . . . . . . . . . . . . . 186, 346
Alarms and Errors . . . . . . . . . . . . . . . . . . . . . 181
A Ambient Temperature Setting . . . .305, 364, 435
A/D Conversion Error . . . . . . . . . 182, 188, 190 Analog Filter Time Constant . . . . . . . . . . . . . 180
A1 Initialization Parameters . . . . . . . . . . . . . . 311 Analog Frequency Reference Fluctuation Limit
A1-01 . . . . . . . . . . . . . . . . . . . . . . . . . . .164, 311 (Up/Down 2) . . . . . . . . . . . . . . . . . . . . . 328, 438
A1-02122, 157, 195, 220, 231, 232, 234, 237, Analog Input Filter Time Constant . . . . 348, 441
311, 433 Application Selection . . . . . . . . . . . . . . 312, 433
A1-03 112, 122, 129, 164, 188, 189, 311, 433 ASR Integral Time 1 (for Simple PG V/f Control)
A1-04 . . . . . . . . . . . . . . . . . . . . . . 165, 228, 311 323, 437
A1-05 . . . . . . . . . . . . . . . . . . 165, 228, 311, 433 ASR Integral Time 2 (for Simple PG V/f Control)
A1-06 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 312 323, 437
A2 User Parameters . . . . . . . . . . . . . . . . . . . . 312 ASR Limit (for Simple PG V/f Control) 323, 437
A2-01 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165 ASR Proportional Gain 1 (for Simple PG V/f

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 443
Control). . . . . . . . . . . . . . . . . . . . . . . . . 323, 437 b3-10 . . . . . . . . . . . . . . . . . . . . . . .203, 315, 434
ASR Proportional Gain 2 (for Simple PG V/f b3-14 . . . . . . . . . . . . . . . . . . . . . . .203, 315, 434
Control). . . . . . . . . . . . . . . . . . . . . . . . . 323, 437 b3-17 . . . . . . . . . . . . . . . . . . . . . . .203, 315, 434
Auto Restart Operation Selection . . . . . 359, 434 b3-18 . . . . . . . . . . . . . . . . . . . . . . .203, 316, 434
Automatic Reduction Selection for Stall b3-19 . . . . . . . . . . . . . . . . . . 201, 203, 316, 434
Prevention during Run . . . . . . . . . . . . . 357, 434 b3-24 . . . . . . . . . . . . . . 198, 199, 201, 316, 434
Auto-Tuning153, 155, 156, 157, 159, 161, 162 b3-25 . . . . . . . . . . . . . . . . . . . . . . . . . . . 316, 434
Auto-Tuning Codes. . . . . . . . . . . . . . . . . . . . . 222 b4 Timer Function . . . . . . . . . . . . . . . . . . . . . 316
Auto-Tuning Fault Codes . . . . . . . . . . . . . . . . 157 b4-01 . . . . . . . . . . . . . . . . . . . . . . . . . . . 316, 434
Auto-Tuning Fault Detection . . . . . . . . . . . . . 222 b4-02 . . . . . . . . . . . . . . . . . . . . . . . . . . . 316, 434
Auto-Tuning Fault Solutions . . . . . . . . . . . . . 222 b5 PID Control. . . . . . . . . . . . . . . . . . . . . . . . 316
Auto-Tuning for V/f Control . . . . . . . . . . . . . 154 b5-01 . . . . . . . . . . . . . . 218, 220, 241, 316, 434
Auto-Tuning Mode Selection . . . . 160, 375, 438 b5-02 . . . . . . . . . 316, 317, 318, 319, 434, 435
Auxiliary Frequency Reference 1. . . . . . . . . . 349 b5-03 . . . . . . . . . . . . . . . . . . . . . . . . . . . 316, 434
b5-04 . . . . . . . . . . . . . . . . . . . . . . . . . . . 316, 434
B b5-05 . . . . . . . . . . . . . . . . . . . . . . . . . . . 316, 434
b1 Operation Mode Selection . . . . . . . . . . . . . 313 b5-06 . . . . . . . . . . . . . . . . . . . . . . . . . . . 317, 434
b1-01 . 124, 126, 170, 229, 313, 410, 411, 433 b5-07 . . . . . . . . . . . . . . . . . . . . . . . . . . . 317, 434
b1-02 127, 128, 200, 219, 229, 313, 410, 411, b5-08 . . . . . . . . . . . . . . . . . . . . . . . . . . . 317, 434
433 b5-09 . . . . . . . . . . . . . . . . . . . . . . .238, 317, 434
b1-03 . . . . . . . . . . . . . . . . . . .129, 130, 131, 220 b5-10 . . . . . . . . . . . . . . . . . . . . . . . . . . . 317, 434
b1-04 . . . . . . . . . . . . . . . . . . . . . . . 231, 240, 313 b5-11 . . . . . . . . . . . . . . . . . . . . . . . . . . . 317, 434
b1-07 . . . . . . . . . . . . . . . . . . . . . . . . . . . 313, 433 b5-12 . . . . . . . . . . . . . . . . . . . . . . .193, 317, 435
b1-08 . . . . . . . . . . . . . . . . . . . . . . . . . . . 313, 433 b5-13 . . . . . . . . . . . . . . . . . . 193, 210, 317, 435
b1-14 . . . . . . . . . . . . . . . . . . . . . . . . . . . 314, 433 b5-13 and b5-14. . . . . . . . . . . . . . . . . . . . . . . 193
b1-15 . . . . . . . . . . . . . . . . . . . . . . . . . . . 314, 433 b5-14 . . . . . . . . . . . . . . . . . . 193, 210, 317, 435
b1-16 . . . . . . . . . . . . . . . . . . . . . . . . . . . 314, 433 b5-15 . . . . . . . . . . . . . . . . . . . . . . . . . . . 318, 435
b1-17 . . . . . . . . . . . . . . . . . . . . . . . . . . . 314, 433 b5-16 . . . . . . . . . . . . . . . . . . . . . . . . . . . 318, 435
b2 DC Injection Braking. . . . . . . . . . . . . . . . . 314 b5-17 . . . . . . . . . . . . . . . . . . . . . . . . . . . 318, 435
b2-01 . . . . . . . . . . . . . . . . . . . . . . . 129, 314, 433 b5-18 . . . . . . . . . . . . . . . . . . . . . . . . . . . 318, 435
b2-02 . . . . . . . . . . . . . . 129, 236, 238, 314, 433 b5-19 . . . . . . . . . . . . . . . . . . . . . . . . . . . 318, 435
b2-03 . . . . . . . . . . . . . . . . . . . . . . . 238, 314, 433 b5-20 . . . . . . . . . . . . . . . . . . . . . . . . . . . 318, 435
b2-04 . . . . . . . . . . . . . . . . . . .129, 238, 314, 434 b5-34 . . . . . . . . . . . . . . . . . . . . . . . . . . . 318, 435
b2-08 . . . . . . . . . . . . . . . . . . . . . . . . . . . 315, 434 b5-35 . . . . . . . . . . . . . . . . . . . . . . . . . . . 318, 435
b2-12 . . . . . . . . . . . . . . . . . . . . . . . . . . . 315, 434 b5-36 . . . . . . . . . . . . . . . . . . 192, 210, 318, 435
b2-15 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 434 b5-36 and b5-37. . . . . . . . . . . . . . . . . . . . . . . 193
b3 Speed Search . . . . . . . . . . . . . . . . . . . . . . . 315 b5-37 . . . . . . . . . . . . . . . . . . 192, 210, 318, 435
b3-01 . . . . . . . . . . . . . . . . . . . . . . . 238, 315, 434 b5-38 . . . . . . . . . . . . . . . . . . . . . . . . . . . 318, 435
b3-02 . . . . . . . . . . . . . . . . . . .198, 201, 315, 434 b5-39 . . . . . . . . . . . . . . . . . . . . . . . . . . . 318, 435
b3-03 . . . . . . . . . . . . . . . . . . .198, 201, 315, 434 b6 Dwell Function . . . . . . . . . . . . . . . . . . . . . 319
b3-05 . . . . . . . . . . . . . . . . . . . . . . . . . . . 315, 434 b6-01 . . . . . . . . . . . . . . . . . . . . . . . . . . . 319, 435

444 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
b6-01 through b6-04 . . . . . . . . . . . . . . . . . . . . 180 C1-03 . . . . . . . . . . . . . . . . . . . . . . .233, 320, 436
b6-02. . . . . . . . . . . . . . . . . . . . . . . . . . . .319, 435 C1-04 . . . . . . . . . . . . . . . . . . . . . . .235, 320, 436
b6-03. . . . . . . . . . . . . . . . . . . . . . . . . . . .319, 435 C1-05 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 233
b6-04. . . . . . . . . . . . . . . . . . . . . . . . . . . .319, 435 C1-06 . . . . . . . . . . . . . . . . . . . . . . .235, 320, 436
b8 Energy Saving . . . . . . . . . . . . . . . . . . . . . . 319 C1-07 . . . . . . . . . . . . . . . . . . . . . . .233, 320, 436
b8-01. . . . . . . . . . . . . . . . . . . . . . . . . . . .319, 435 C1-08 . . . . . . . . . . . . . . . . . . . . . . .235, 320, 436
b8-02. . . . . . . . . . . . . . . . . . . . . . . . . . . .319, 435 C1-09 . . . . . . . . . . . . . . . . . . . . . . .132, 321, 436
b8-03. . . . . . . . . . . . . . . . . . . . . . . . . . . .319, 435 C1-10 . . . . . . . . . . . . . . . . . . . . . . .132, 321, 436
b8-04. . . . . . . . . . . . . . . . . . . . . . . . . . . .319, 435 C1-11 . . . . . . . . . . . . . . . . . . . . . . .133, 321, 436
b8-05. . . . . . . . . . . . . . . . . . . . . . . . . . . .319, 435 C2 S-Curve Characteristics . . . . . . . . . . . . . . 321
b8-06. . . . . . . . . . . . . . . . . . . . . . . . . . . .319, 435 C2-01 . . . . . . . . . . . . . . . . . . . . . . .203, 321, 436
Base Frequency . . . . . . . . . . . . . . . . . . . . . . . 198 C2-01 through C2-04. . . . . . . . . . . . . . . 180, 195
Base Frequency (FA) . . . . . . . . . . . . . . .331, 438 C2-02 . . . . . . . . . . . . . . . . . . . . . . . . . . . 321, 436
Base Voltage (VBASE) . . . . . . . . . . . . .331, 438 C2-03 . . . . . . . . . . . . . . . . . . . . . . . . . . . 321, 436
Baseblock . . . . . . . . . . . . . . . . . . . . . . . . . . . . 206 C2-04 . . . . . . . . . . . . . . . . . . . . . . . . . . . 321, 436
Baseblock 2 . . . . . . . . . . . . . . . . . . . . . . . . . . 347 C3 Slip Compensation. . . . . . . . . . . . . . . . . . 321
Baseblock Command (N.C.). . . . . . . . . . . . . . 342 C3-01 . . . . . . . . . . . . . . . . . . . . . . . . . . . 177, 179
Baseblock Command (N.O.) . . . . . . . . . . . . . 342 C3-02 . . . . . . . . . . . . . . . . . . 179, 237, 321, 436
Baseblock Signal Input. . . . . . . . . 184, 210, 211 C3-03 . . . . . . . . . . . . . . . . . . . . . . .234, 322, 436
Basic Drive Operation . . . . . . . . . . . . . . . . . . 122 C3-04 . . . . . . . . . . . . . . . . . . . . . . . . . . . 322, 436
bb . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .184, 206 C3-05 . . . . . . . . . . . . . . . . . . . . . . . . . . . 322, 436
Bi-Directional Speed Search Selection .315, 434 C4 Torque Compensation . . . . . . . . . . . . . . . 322
Braking Resistor . . . . . . . . . . . . . . . . . . . . . . . . 82 C4-01 . . . . . . . . . . . . . . . . . . 177, 195, 199, 230
Braking Resistor Adjustments . . . . . . . . . . . . . 83 C4-02 . . . . . 177, 178, 220, 237, 239, 322, 436
Braking Resistor Fault . . . . . . . . . . . . . . . . . . 346 C4-03 . . . . . . . . . . . . . . . . . . . . . . . . . . . 322, 436
Braking Resistor Overheat . . . . . . . . . . . . . . . 202 C4-05 . . . . . . . . . . . . . . . . . . . . . . .322, 323, 436
Braking Resistor, Installation . . . . . . . . . . . . . . 82 C4-06 . . . . . . . . . . . . . . . . . . . . . . .178, 179, 220
bUS . . . . . . . . . . . . . . . . . . . . 182, 184, 187, 206 C5 Speed Control (ASR). . . . . . . . . . . . . . . . 323
Buzzing Sound from Motor at 2 kHz . . . . . . . 239 C5-01 . . . . . . . . . . . . . . . . . . . . . . . . . . . 200, 213
C5-02 . . . . . . . . . . . . . . . . . . . . . . . . . . . 200, 213
C C6 Carrier Frequency . . . . . . . . . . . . . . . . . . 323
C Tuning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 320 C6-01 . . . . . . . . . . . . . . . . . . . . . . .177, 323, 437
C1 Acceleration and Deceleration Times. . . . 320 C6-02 . 84, 177, 179, 196, 199, 235, 236, 237,
C1-01 . . . . .103, 132, 223, 224, 233, 320, 436 241, 324, 437
C1-01 through C1-08 .191, 197, 198, 199, 202, C6-03 . . . . . . . . . . . . . . . . . . . . . . . . . . . 324, 437
203, 208, 211, 212 C6-04 . . . . . . . . . . . . . . . . . . . . . . . . . . . 324, 437
C1-01 through C1-11 . . . . . . . . . . . . . . . . . . . 180 C6-05 . . . . . . . . . . . . . . . . . . . . . . .237, 324, 437
C1-01, -03, -05, -07 . . . . . . . . . . . . . . . . . . . . 195 Cable Length Between Drive and Motor . . . . 67
C1-02 . . . . . . . . . . . . . 132, 188, 235, 320, 436 CALL. . . . . . . . . . . . . . . . . . . . . . . . . . . 184, 207
C1-02, -04, -06 and -08 . . . . . . . . . . . . . . . . . 200 Cannot Change Parameter Settings . . . . . . . . 228
C1-02, -04, -06, -08 . . . . . . . . . . . . . . . . . . . . 200 Capacitor Maintenance . . . . . . . . . . . . . 151, 383

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 445
Capacitor Maintenance Setting. . . . . . . 372, 437 Copy Allowed Selection . . . . . . . . . . . . . . . . 437
Carrier Frequency Lower Limit . . . . . . 324, 437 Copy Function Selection . . . . . . . . . . . . . . . . 437
Carrier Frequency Proportional Gain . . 324, 437 Copy Mode Selection . . . . . . . . . . . . . . . . . . 437
Carrier Frequency Reduction . . . . . . . . 365, 435 CPF02 . . . . . . . . . . . . . . . . . . . . . . . . . . 182, 188
Carrier Frequency Selection .177, 179, 324, 437 CPF03 . . . . . . . . . . . . . . . . . . . . . . . . . . 182, 188
Carrier Frequency Setting Error . . . . . . 186, 221 CPF06 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 189
Carrier Frequency Upper Limit . . . . . . 324, 437 CPF07 . . . . . . . . . . . . . . . . . . . . . . . . . . 182, 189
CE . . . . . . . . . . . . . . . . . . . . .182, 184, 187, 207 CPF08 . . . . . . . . . . . . . . . . . . . . . . . . . . 182, 189
CE Detection Time . . . . . . . . . . . . . . . . 350, 442 CPF11 . . . . . . . . . . . . . . . . . . . . . . . . . . 182, 189
CE mark . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 417 CPF12 . . . . . . . . . . . . . . . . . . . . . . . . . . 183, 189
CF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182, 188 CPF13 . . . . . . . . . . . . . . . . . . . . . . . . . . 183, 189
CI-01 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 240 CPF14 . . . . . . . . . . . . . . . . . . . . . . . . . . 183, 190
clock error. . . . . . . . . . . . . . . . . . . . . . . . . . . . 190 CPF16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183
Clock Fault . . . . . . . . . . . . . . . . . . . . . . 183, 190 CPF17 . . . . . . . . . . . . . . . . . . . . . . . . . . 183, 190
Coast to Stop. . . . . . . . . . . . . . . . . . . . . . . . . . 130 CPF18 . . . . . . . . . . . . . . . . . . . . . . . . . . 183, 190
Coast to Stop with Timer . . . . . . . . . . . . . . . . 131 CPF19 . . . . . . . . . . . . . . . . . . . . . . . . . . 183, 190
Communication Fault Detection Selection. . 350, CPF20 . . . . . . . . . . . . . . . . . . . . . . . . . . 183, 190
442 CPF21 . . . . . . . . . . . . . . . . . . . . . . . . . . 183, 190
Communication Parity Selection . . . . . 350, 442 CPF22 . . . . . . . . . . . . . . . . . . . . . . . . . . 182, 190
Communication Speed Selection . . . . . 350, 442 CPF23 . . . . . . . . . . . . . . . . . . . . . . . . . . 182, 191
Communications ENTER Function Selection351, CPF24 . . . . . . . . . . . . . . . . . . . . . . . . . . 182, 191
442 Cumulative Operation Time at 10th Most Recent
Communications Test Mode . . . . . . . . . . . . . . 344 Fault . . . . . . . . . . . . . . . . . . . . . . . .151, 383, 441
Connected Machinery Vibrates When Motor Cumulative Operation Time at 2th Most Recent
Rotates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 236 Fault . . . . . . . . . . . . . . . . . . . . . . . .150, 382, 441
Constant Torque . . . . . . . . . . . . . . . . . . . . . . . 140 Cumulative Operation Time at 3th Most Recent
Control Circuit Connection Diagram . . . . . . . . 69 Fault . . . . . . . . . . . . . . . . . . . . . . . .150, 382, 441
Control Circuit Fault. . . . . . . . . . . . . . . 183, 190 Cumulative Operation Time at 4th Most Recent
Control Circuit Input Terminals . . . . . . . . . . . . 70 Fault . . . . . . . . . . . . . . . . . . . . . . . .150, 382, 441
Control Circuit Output Terminals . . . . . . . . . . . 71 Cumulative Operation Time at 5th Most Recent
Control Circuit Terminal Block Configuration72, Fault . . . . . . . . . . . . . . . . . . . . . . . .150, 382, 441
409 Cumulative Operation Time at 6th Most Recent
Control Circuit Terminal Block Functions . . . . 70 Fault . . . . . . . . . . . . . . . . . . . . . . . .151, 382, 441
Control Fault. . . . . . . . . . . . . . . . . . . . . 182, 188 Cumulative Operation Time at 7th Most Recent
Control Method Selection. . . . . . . . . . . 311, 433 Fault . . . . . . . . . . . . . . . . . . . . . . . .151, 382, 441
Control Mode . . . . . . . . . . . . . . . . 150, 377, 439 Cumulative Operation Time at 8th Most Recent
Control Power Supply Undervoltage . . . . . . . 183 Fault . . . . . . . . . . . . . . . . . . . . . . . .151, 383, 441
Cooling Fan Maintenance Setting (Operation Cumulative Operation Time at 9th Most Recent
Time). . . . . . . . . . . . . . . . . . . . . . . . . . . 372, 437 Fault . . . . . . . . . . . . . . . . . . . . . . . .151, 383, 441
Cooling Fan Operation Time . . . . 151, 383, 441 Cumulative Operation Time at Most Recent Fault
Cooling Fan Replacement. . . . . . . . . . . . . . . . 254 150, 382, 441

446 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
Cumulative Operation Time at Previous Fault151, d4-08 . . . . . . . . . . . . . . . . . . . . . . . . . . . 328, 438
381, 440 d4-09 . . . . . . . . . . . . . . . . . . . . . . . . . . . 328, 438
Current Alarm. . . . . . . . . . . . . . . . . . . . .185, 211 d7 Offset Frequency . . . . . . . . . . . . . . . . . . . 329
Current Alarm Selection. . . . . . . . . . . . .365, 435 d7-01 . . . . . . . . . . . . . . . . . . . . . . . . . . . 329, 438
Current Detection Error . . . . . . . . . . . . .186, 224 d7-03 . . . . . . . . . . . . . . . . . . . . . . . . . . . 329, 438
Current Fault. . . . . . . . . . . . . . . . . 151, 380, 439 d-Axis ACR Output. . . . . . . . . . . .152, 386, 442
Current Offset Fault . . . . . . . . . . . . . . . . . . . . 188 DC Bus Overvoltage . . . . . . . . . . . . . . . . . . . 213
Current Unbalance Detection (LF2). . . .365, 435 DC Bus Undervoltage . . . . . . . . . . . . . . 204, 346
DC Bus Voltage . . . . . . . . . . . . . . .151, 377, 439
D DC Bus Voltage at Previous Fault .151, 381, 440
d References . . . . . . . . . . . . . . . . . . . . . . . . . . 325 DC Injection Braking . . . . . . . . . . . . . . . . . . 236
d1 Frequency Reference . . . . . . . . . . . . . . . . . 325 DC Injection Braking at start. . . . . . . . . . . . . 238
d1-01. . . . . . . . . . . . . . 168, 170, 325, 326, 437 DC Injection Braking at Stop . . . . . . . . . . . . 238
d1-02. . . . . . . . . . . . . . . . . . . . . . . 168, 325, 437 DC Injection Braking Command. . . . . . . . . . 343
d1-03. . . . . . . . . . . . . . . . . . . . . . . 168, 325, 437 DC Injection Braking Current . . . .238, 314, 433
d1-04. . . . . . . . . . . . . . . . . . . . . . . 168, 325, 437 DC Injection Braking Current 2 . . . . . . . . . . 434
d1-05. . . . . . . . . . . . . . . . . . . . . . . . . . . .325, 437 DC Injection Braking Start Frequency . 314, 433
d1-07. . . . . . . . . . . . . . . . . . . . . . . . . . . .325, 437 DC Injection Braking Time/DC Excitation Time at
d1-09. . . . . . . . . . . . . . . . . . . . . . . . . . . .325, 437 Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . 314, 433
d1-10. . . . . . . . . . . . . . . . . . . . . . . . . . . .325, 437 DC Injection Braking to Stop . . . . . . . . . . . . 130
d1-11 . . . . . . . . . . . . . . . . . . . . . . . . . . . .326, 437 Deceleration Rate Calculation Gain . . . 357, 434
d1-12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 437 Deceleration Takes Too Long With Dynamic
d1-15. . . . . . . . . . . . . . . . . . . . . . . . . . . .326, 437 Braking Enabled . . . . . . . . . . . . . . . . . . . . . . 235
d1-16. . . . . . . . . . . . . . . . . . . . . . . . . . . .326, 437 Deceleration Time 1 . . . . . . . . . . .132, 320, 436
d1-17. . . . . . . . . . . . . . . . . . . . . . . 166, 326, 437 Deceleration Time 2 . . . . . . . . . . . . . . . 320, 436
d2 Frequency Upper and Lower Limits . . . . . 326 Deceleration Time 3 (Motor 2 Decel Time 1)320,
d2-01. . . . . . . . . . . . . . . . . . . . . . . 239, 326, 437 436
d2-02. . . . . . . . . . . . . . . . . . . . . . . . . . . .326, 437 Deceleration Time 4 . . . . . . . . . . . . . . . 320, 436
d2-03. . . . . . . . . . . . . . . . . . . . . . . . . . . .326, 437 Deceleration Time at Stall Prevention during
d3 Jump Frequency. . . . . . . . . . . . . . . . . . . . . 327 Acceleration. . . . . . . . . . . . . . . . . . . . . . 357, 434
d3-01. . . . . . . . . . . . . . . . . . . . . . . 237, 327, 437 Derated Torque . . . . . . . . . . . . . . . . . . . . . . . 141
d3-01 through d3-03 . . . . . . . . . . . . . . . . . . . . 239 Derivative Time. . . . . . . . . . . . . . . . . . . 316, 434
d3-01 through d3-04 . . . . . . . . . . . . . . . . . . . . 180 dEv. . . . . . . . . . . . . . . . . . . . 182, 184, 191, 208
d3-02. . . . . . . . . . . . . . . . . . . . . . . . . . . .327, 438 Differential PID Feedback. . . . . . . . . . . . . . . 349
d3-03. . . . . . . . . . . . . . . . . . . . . . . . . . . .327, 438 Digital Operator Connection Fault . . . . . . . . 200
d3-04. . . . . . . . . . . . . . . . . . . . . . . 237, 327, 438 Digital Operator Display Selection . . . . 370, 436
d4 Frequency Reference Hold . . . . . . . . . . . . 327 DIP Switch S1 . . . . . . . . . . . . . . . . . . . . . . . . . 80
d4-01. . . . . . . . . . . . . . . . . . . . . . . . . . . .327, 438 dnE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184, 208
d4-04. . . . . . . . . . . . . . . . . . . 327, 328, 329, 438 Down 2 Command. . . . . . . . . . . . . . . . . . . . . 344
d4-06. . . . . . . . . . . . . . . . . . . . . . . . . . . .328, 438 Down Command . . . . . . . . . . . . . . . . . . . . . . 342
d4-07. . . . . . . . . . . . . . . . . . . . . . . . . . . .328, 438 Drive Baseblock . . . . . . . . . . . . . . . . . . . . . . 184

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 447
Drive Capacity Setting Fault . . . . . . . . . . . . . 217 Dynamic Braking Transistor . . . . . . . . . 183, 203
Drive Capacity Signal Fault . . . . . . . . . 182, 191
Drive Cooling Fans. . . . . . . . . . . . . . . . . . . . . 254 E
Drive Disabled . . . . . . . . . . . . . . . . . . . 184, 208 çÝëÂìKópÉÇÅ . . . . . . . . . . 293, 294, 296, 297
Drive Does Not Allow Selection of Rotational E1 V/f Pattern Characteristics . . . . . . . . . . . . 330
Auto-Tuning . . . . . . . . . . . . . . . . . . . . . . . . . . 232 E-10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230
Drive Enable . . . . . . . . . . . . . . . . . . . . . 344, 347 E1-01 . . . . . . . . . . . . . . . . . . . . . . . . . . . 138, 438
Drive Input Voltage Setting . . . . . . . . . . . . . . 138 E1-03 .139, 140, 230, 233, 235, 330, 389, 438
Drive Intended Use . . . . . . . . . . . . . . . . . . . . . . 12 E1-03 V/F Pattern Settings . . . . . . . . . . . . . . 389
Drive kVA Setting Error . . . . . . . . . . . . . . . . . 185 E1-03 V/F Pattern Settings for Drive Capacity
Drive Mode. . . . . . . . . . . . . . . .97, 98, 100, 347 200/400 V . . . . . . . . . . . . . . . . . . . . . . . . 389
Drive Mode Unit Monitor Selection. . . 370, 436 E1-04 139, 220, 233, 235, 239, 241, 331, 389,
Drive Models and Types . . . . . . . . . . . . . . . . . . 44 438
Drive Motor Overload Protection. . . . . . . . . . 428 E1-04 through E1-10 . . 195, 197, 198, 199, 212
Drive Node Address . . . . . . . . . . . . . . . 350, 442 E1-05 . . . . . . . . . . . . . . 139, 331, 389, 390, 438
Drive Operation Status at Previous Fault151, 381, E1-06 .140, 150, 198, 235, 331, 389, 390, 438
440 E1-07 . . . . . . . . . 140, 220, 331, 389, 390, 438
Drive Overheat . . . . . . . . . . . . . . . . . . . . . . . . 185 E1-08 139, 177, 179, 197, 198, 199, 230, 331,
Drive Overheat Alarm (OH2). . . . . . . . . . . . . 342 389, 390, 438
Drive Overheat Warning. . . . . . . . . . . . . . . . . 212 E1-08 and E1-10 . . . . . . . . . . . . . . . . . . . . . . 212
Drive Overload . . . . . . . . . . . . . . . . . . . 183, 198 E1-09 139, 220, 229, 230, 240, 331, 389, 390,
Drive Ready . . . . . . . . . . . . . . . . . . . . . . . . . . 346 438
Drive Replacement . . . . . . . . . . . . . . . . . . . . . 258 E1-10 140, 177, 179, 197, 198, 199, 230, 235,
Drive Short-Circuit Rating . . . . . . . . . . . . . . . 428 331, 389, 438
Drive Status. . . . . . . . . . . . . . . . . . 151, 379, 439 E1-12 . . . . . . . . . . . . . . . . . . . . . . . . . . . 331, 438
Drive Status Monitors. . . . . . . . . . . . . . . . . . . 150 E1-13 . . . . . . . . . . . . . . . . . . . . . . . . . . . 331, 438
Drive Transmit Wait Time . . . . . . . . . . 350, 442 E2 Motor Parameters . . . . . . . . . . . . . . . . . . . 331
Drive Watts Loss Data . . . . . . . . . . . . . . . . . . 302 E2-01 .142, 147, 177, 197, 198, 331, 428, 438
Drive/kVA Selection . . . . . . . . . . . . . . . 371, 436 E2-02 . . . . . . . . . . . . . . . . . . 143, 177, 331, 438
During Baseblock . . . . . . . . . . . . . . . . . . . . . . 346 E2-03 . . . . . . . . . . . . . . 143, 177, 222, 331, 438
During Fast-stop . . . . . . . . . . . . . . . . . . . . . . . 347 E2-04 . . . . . . . . . . . . . . . . . . . . . . .143, 332, 438
During Run . . . . . . . . . . . . . . . . . . . . . . . . . . . 345 E2-05 . . . . . . . . . . . . . . . . . . . . . . .143, 332, 439
During Run 2, Motor Switch Command Input185 E2-06 . . . . . . . . . . . . . . . . . . . . . . .143, 332, 439
During Torque Limit. . . . . . . . . . . . . . . . . . . . 347 E2-07 . . . . . . . . . . . . . . . . . . 143, 224, 332, 439
Duty Cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . 437 E2-08 . . . . . . . . . . . . . . . . . . 143, 224, 332, 439
Dwell Frequency at Stop. . . . . . . . . . . . 319, 435 E2-09 . . . . . . . . . . . . . . . . . . . . . . .143, 332, 439
Dwell Function . . . . . . . . . . . . . . . . . . . . . . . . 180 E2-10 . . . . . . . . . . . . . . . . . . . . . . .143, 332, 439
Dwell Reference at Start . . . . . . . . . . . . 319, 435 E2-11 . . . . . . . . . . . . . . . . . . . . . . .143, 332, 439
Dwell Time at Start. . . . . . . . . . . . . . . . 319, 435 E2-12 . . . . . . . . . . . . . . . . . . 142, 143, 332, 439
Dwell Time at Stop . . . . . . . . . . . . . . . . 319, 435 E3 Motor 2 V/f Characteristics . . . . . . . . . . . 332
Dynamic Braking Resistor . . . . . . . . . . . . . . . 183 E3-01 . . . . . . . . . . . . . . . . . . . . . . . . . . . 332, 439

448 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
E3-04 . . . . . . . . . . . . . . . . . . . . . . . . . . .333, 439 EF2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192, 209
E3-04 through E3-10 . . . . . . . . . . . . . . . . . . . 195 EF3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192, 209
E3-05 . . . . . . . . . . . . . . . . . . . . . . . . . . .333, 439 EF4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192, 209
E3-06 . . . . . . . . . . . . . . . . . . . . . . 220, 333, 439 EF5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192, 209
E3-07 . . . . . . . . . . . . . . . . . . . . . . . . . . .333, 439 EF6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192, 209
E3-08 . . . . . . . . . . . . . . . . . . . . . . . . . . .333, 439 EF7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192, 209
E3-09 . . . . . . . . . . . . . . . . . . . . . . . . . . .333, 439 Electrical Thermal Motor Protection. . . . . . . 146
E3-10 . . . . . . . . . . . . . . . . . . . . . . . . . . .333, 439 EMC Guidelines . . . . . . . . . . . . . . . . . . . . . . 417
E3-11 . . . . . . . . . . . . . . . . . . . . . . . . . . .333, 439 End1. . . . . . . . . . . . . . . . . . . . . . . . . . . . 186, 224
E3-12 . . . . . . . . . . . . . . . . . . . . . . . . . . .333, 439 End2. . . . . . . . . . . . . . . . . . . . . . . . . . . . 186, 224
E4 Motor 2 Parameters. . . . . . . . . . . . . . . . . . 333 End3. . . . . . . . . . . . . . . . . . . . . . . . . . . . 186, 225
E4-01 . . . . . . . . . . . . . . . . . . . . . . 147, 333, 439 Energy Saving Coefficient Value . . . . . 319, 435
E4-02 . . . . . . . . . . . . . . . . . . . . . . . . . . .333, 439 Energy Saving Control Filter Time Constant 319,
E4-03 . . . . . . . . . . . . . . . . . . . . . . . . . . .333, 439 435
E4-04 . . . . . . . . . . . . . . . . . . . . . . . . . . .334, 439 Energy Saving Control Selection . . . . . 319, 435
E4-05 . . . . . . . . . . . . . . . . . . . . . . . . . . .334, 439 Energy Saving Gain. . . . . . . . . . . . . . . . 319, 435
E4-06 . . . . . . . . . . . . . . . . . . . . . . . . . . .334, 439 Energy Savings Coefficient Calculation Value . .
E4-07 . . . . . . . . . . . . . . . . . . . . . . . . . . .334, 439 152, 442
E4-08 . . . . . . . . . . . . . . . . . . . . . . . . . . .334, 439 Er-01 . . . . . . . . . . . . . . . . . . . . . . . . . . . 186, 222
E4-09 . . . . . . . . . . . . . . . . . . . . . . . . . . .334, 440 Er-02 . . . . . . . . . . . . . . . . . . . . . . . . . . . 186, 222
E4-10 . . . . . . . . . . . . . . . . . . . . . . . . . . .334, 440 Er-03 . . . . . . . . . . . . . . . . . . . . . . . . . . . 186, 222
E4-11 . . . . . . . . . . . . . . . . . . . . . . . . . . .334, 440 Er-04 . . . . . . . . . . . . . . . . . . . . . . . . . . . 186, 223
E4-12 . . . . . . . . . . . . . . . . . . . . . . . . . . .334, 440 Er-05 . . . . . . . . . . . . . . . . . . . . . . . . . . . 186, 223
E4-14 . . . . . . . . . . . . . . . . . . . . . . . . . . .334, 440 Er-08 . . . . . . . . . . . . . . . . . . . . . . . . . . . 186, 223
E4-15 . . . . . . . . . . . . . . . . . . . . . . . . . . .334, 440 Er-09 . . . . . . . . . . . . . . . . . . . . . . . . . . . 186, 223
E5 PM Motor Parameters . . . . . . . . . . . . . . . . 335 Er-11 . . . . . . . . . . . . . . . . . . . . . . . . . . . 186, 224
E5-01 . . . . . . . . . . . . . . . . . . 195, 203, 220, 239 Er-12 . . . . . . . . . . . . . . . . . . . . . . . . . . . 186, 224
E5-02 . . . . . . . . . . . . . . . . . . . . . . . . . . .335, 440 Err . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192
E5-03 . . . . . . . . . . . . . . . . . . . . . . 220, 335, 440 European Standards . . . . . . . . . . . . . . . . . . . . 417
E5-04 . . . . . . . . . . . . . . . . . . . . . . . . . . .335, 440 Excessive Motor Oscillation and Erratic Rotation
E5-06 . . . . . . . . . . . . . . . . . . . . . . . . . . .335, 440 236
E5-09 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220 Excessive PID Feedback . . . 182, 184, 192, 210
E5-24 . . . . . . . . . . . . . . . . . . . . . . 220, 336, 440 Excessive Speed Deviation (for Simple V/f with
EEPROM Data Error . . . . . . . . . . . . . . . . . . . 189 PG). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182, 184
EEPROM Serial Communication Fault . . . . . 189 Excessive Speed Deviation Detection Delay Time
EEPROM Serial Communications Fault . . . . 182 (for Simple PG V/f Control) . . . . . . . . . . . . . 440
EEPROM Write Error . . . . . . . . . . . . . . . . . . 192 Excessive Speed Deviation Detection Level (for
EF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .184, 208 Simple PG V/f Control). . . . . . . . . . . . . . . . . 440
EF0 . . . . . . . . . . . . . . . . . . . . 182, 184, 191, 209 Excessive V/f Setting . . . . . . . . . . . . . . 186, 224
EF1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .192, 209 External Fault . . . . . . . . . . . . . . . . . . . . 192, 210
EF1 to EF7 . . . . . . . . . . . . . . . . . . . . . . .182, 184 External Fault (input terminal S1 to S7) 182, 184

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 449
External Fault (user selection possible) . . . . . 343 FLASH Memory Fault. . . . . . . . . . . . . . 183, 189
External Search Command 1 . . . . . . . . . . . . . 344 FMAX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
External Search Command 2 . . . . . . . . . . . . . 344 FMIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
Forward Jog . . . . . . . . . . . . . . . . . . . . . . . . . . 342
F Forward Regenerative Torque Limit . . . 363, 434
F1 Simple PG V/f Parameters. . . . . . . . . . . . . 336 Forward Run Command (2-wire sequence). . 343
F1-02. . . . . . . . . . . . . . . . . . . . . . . . . . . 337, 440 Forward Torque Limit . . . . . . . . . . . . . . 363, 434
F1-03. . . . . . . . . . . . . . . . . . . . . . . . . . . 337, 440 Forward/Reverse Run Command Input Error 208
F1-04. . . . . . . . . . . . . . . . . . . . . . . . . . . 337, 440 Fref/Fout Agree 1 . . . . . . . . . . . . . . . . . . . . . 345
F1-08. . . . . . . . . . . . . . . . . . .200, 213, 337, 440 Fref/Fout Agree 2 . . . . . . . . . . . . . . . . . . . . . 346
F1-08 and F1-09 . . . . . . . . . . . . . . . . . . . . . . . 200 Fref/Fset Agree 1 . . . . . . . . . . . . . . . . . . . . . . 345
F1-09. . . . . . . . . . . . . . . . . . . . . . . 213, 337, 440 Fref/Fset Agree 2 . . . . . . . . . . . . . . . . . . . . . . 346
F1-10. . . . . . . . . . . . . . . . . . .191, 208, 337, 440 Frequency (FOUT) Detection 1. . . . . . . . . . . 345
F1-10 and F1-11 . . . . . . . . . . . . . . . . . . . . . . . 191 Frequency (FOUT) Detection 2. . . . . . . . . . . 345
F1-11 . . . . . . . . . . . . . . . . . . .191, 208, 337, 440 Frequency Bias (A1) . . . . . . . . . . . . . . . . . . . 348
F1-14. . . . . . . . . . . . . . . . . . .202, 214, 338, 440 Frequency Detection 3. . . . . . . . . . . . . . . . . . 346
F6 and F7 Serial Communications Option Card Frequency Detection 4. . . . . . . . . . . . . . . . . . 346
Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 338 Frequency Gain . . . . . . . . . . . . . . . . . . . . . . . 349
F6-03. . . . . . . . . . . . . . . . . . . . . . . . . . . 192, 209 Frequency Reduction Rate during OH Pre-Alarm
FA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140 365, 435
Fast-stop (N.C.) . . . . . . . . . . . . . . . . . . . . . . . 342 Frequency Reference . . . . . . . . . . .150, 376, 439
Fast-Stop (N.O.) . . . . . . . . . . . . . . . . . . . . . . . 342 Frequency Reference (Current) Terminal A2 Input
Fast-stop Time . . . . . . . . . . . . . . . . . . . 321, 436 Bias . . . . . . . . . . . . . . . . . . . . . . . . . . . . 348, 441
Fault . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 346 Frequency Reference 1 . . . . . . . . .168, 325, 437
Fault Causes and Solutions. . . . . . . . . . . . . . . 187 Frequency Reference 10 . . . . . . . . . . . . 325, 437
Fault Detection . . . . . . . . . . . . . . . . . . . . . . . . 187 Frequency Reference 11 . . . . . . . . . . . . 326, 437
Fault Displays . . . . . . . . . . . . . . . . . . . . . . . . . 187 Frequency Reference 12 . . . . . . . . . . . . . . . . 437
Fault History . . . . . . . . . . . . . . . . . . . . . 226, 227 Frequency Reference 13 . . . . . . . . . . . . 326, 437
Fault Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . 342 Frequency Reference 14 . . . . . . . . . . . . 326, 437
Fault Reset Example . . . . . . . . . . . . . . . . . . . . 227 Frequency Reference 15 . . . . . . . . . . . . 326, 437
Fault Reset Interval Time . . . . . . . . . . . 359, 434 Frequency Reference 16 . . . . . . . . . . . . 326, 437
Fault Reset Operation Selection . . . . . . 359, 434 Frequency Reference 2168, 236, 314, 325, 433,
Fault Reset when Run Command Entered . . . 215 437
Fault Trace Example . . . . . . . . . . . . . . . . . . . . 227 Frequency Reference 3 . . . . . . . . .168, 325, 437
Faults. . . . . . . . . . . . . . . . . . . . . . . . . . . 181, 182 Frequency Reference 4 . . . . . . . . .168, 325, 437
FB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140 Frequency Reference 5 . . . . . . . . . . . . . 325, 437
FbH . . . . . . . . . . . . . . . . . . . .182, 184, 192, 210 Frequency Reference 6 . . . . . . . . . . . . . 325, 437
FbL . . . . . . . . . . . . . . . . . . . .182, 184, 193, 210 Frequency Reference 7 . . . . . . . . . . . . . 325, 437
Feedback Detection Control Time Constant 2 232 Frequency Reference 8 . . . . . . . . . . . . . 325, 437
FJOG/RJOG . . . . . . . . . . . . . . . . . . . . . . . . . . 166 Frequency Reference 9 . . . . . . . . . . . . . 325, 437
FLASH memory error. . . . . . . . . . . . . . . . . . . 190 Frequency Reference Accel/Decel (Up/Down 2)

450 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
327, 438 Ground Fault Interrupter Activates When Drive is
Frequency Reference at Previous Fault 151, 380, Running . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 241
439 Ground Wiring. . . . . . . . . . . . . . . . . . . . . . . . . 67
Frequency Reference at Reference Loss 358, 434
Frequency Reference Bias (Up/Down 2)152, 328,
H
386, 438, 442 H1 Multi-Function Digital Input . . . . . . . . . . 341
Frequency Reference Bias Operation Mode H1 Multi-Function Digital Input Selections . 341
Selection (Up/Down 2). . . . . . . . . . . . . .328, 438 H1-01. . . . . . . . . . . . . . . . . . 104, 166, 341, 441
Frequency Reference Bias Step (Up/Down 2) 327 H1-01 through H1-07 . . . . . . . . . . . . . . . . . . 230
Frequency Reference Bias Step(Up/Down 2) 438 H1-01 through H1-10 . . . . . . . . . . . . . . . . . . 228
Frequency Reference from MEMOBUS/Modbus H1-01 through to H1-07 . . . . . . . . . . . . . . . . 217
Communications. . . . . . . . . . . . . . . . . . .151, 442 H1-02. . . . . . . . . . . . . . . . . . . . . . . . . . . 341, 441
Frequency Reference Hold Function Selection . H1-03. . . . . . . . . . . . . . . . . . . . . . . . . . . 341, 441
327, 438 H1-04. . . . . . . . . . . . . . . . . . . . . . . . . . . 341, 441
Frequency Reference Loss Detection Selection . H1-05. . . . . . . . . . . . . . . . . . . 57, 168, 341, 441
358, 434 H1-06. . . . . . . . . . . . . . . . . . . . . . .168, 341, 441
Frequency Reference Lower Limit (Up/Down 2) H1-07. . . . . . . . . . . . . . 104, 166, 167, 341, 441
328, 438 H2 Multi-Function Digital Output Settings. . 345
Frequency Reference Selection . . . . . . .313, 433 H2 Multi-Function Digital Outputs. . . . . . . . 344
Frequency Reference Selection 1 . . . . . . . . . . 229 H2-0. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
Frequency Reference Selection Results 151, 384, H2-01. . . . . . . . . . . . . . 144, 147, 236, 345, 441
442 H2-01 to H2-03 . . . . . . . . . . . . . . . . . . . . . . . 206
Frequency Reference Setting / Decimal Display H2-02. . . . . . . . . . . . . . . . . . . . . . .144, 345, 441
370, 436 H2-03. . . . . . . . . . . . . . . . . . . . . . .147, 345, 441
Frequency Reference Setting and User-Set Display H2-06. . . . . . . . . . . . . . . . . . . . . . . . . . . 345, 441
370, 436 H3 Analog Inputs . . . . . . . . . . . . . . . . . . . . . 348
Frequency Reference Setting Method Selection . H3 Multi-Function Analog Input Settings. . . 348
371, 437 H3-01. . . . . . . . . . . . . . . . . . . . . . . . . . . 348, 441
Frequency Reference Upper Limit . . . . .326, 437 H3-02. . . . . . 79, 197, 233, 235, 238, 348, 441
Frequency Reference Upper Limit (Up/Down 2) H3-02 and H3-10. . . . . . . . . . . . . . . . . . . . . . 219
328, 438 H3-02 or H13-10 . . . . . . . . . . . . . . . . . . . . . . 212
Frequency Reference Wiring . . . . . . . . . . . . . . 76 H3-03. . . . . . . . . . . . . . . . . . . . . . . . . . . 233, 234
FWD Torque Limit . . . . . . . . . . . . . . . . . . . . . 349 H3-04. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 234
FWD/REV Command (2-wire sequence 2) . . 343 H3-09. . . . . . . . . . . . . . . . 79, 80, 229, 348, 441
FWD/REV Torque Limit . . . . . . . . . . . . . . . . 349 H3-09 Details . . . . . . . . . . . . . . . . . . . . . . . . . 80
H3-10. . . . . . . . . . . . . . . 79, 197, 233, 235, 238
G H3-11 . . . . . . . . . . . . . . . . . . . . . . .233, 234, 238
General Safety Information . . . . . . . . . . . . . . . 14 H3-13. . . . . . . . . . . . . . . . . . . . . . . . . . . 180, 237
General-purpose motor. . . . . . . . . . . . . . . . . . 148 H4 Multi-Function Analog Outputs . . . . . . . 349
GF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .182, 193 H4-01. . . . . . . . . . . . . . . . . . . . . . .145, 349, 442
Ground Fault. . . . . . . . . . . . . . . . . . . . . .182, 193 H4-02. . . . . . . . . . . . . . . . . . 145, 146, 349, 442

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 451
H4-03 . . . . . . . . . . . . . . . . . .145, 146, 349, 442 High-Slip Braking Dwell Time at Stop . 367, 436
H5 MEMOBUS/Modbus Communications . . 350 High-slip Braking OL . . . . . . . . . . . . . . . . . . 199
H5-01 . . . . . . . . . . . . . . . . . . . . . . 350, 410, 442 High-Slip Braking Overload Time . . . . 367, 436
H5-01 to H5-07. . . . . . . . . . . . . . . . . . . . . . . . 409 High-slip Braking Overload Time . . . . . . . . . 200
H5-02 . . . . . . . . . . . . . . . . . . . . . . 350, 410, 442 High-Slip Suppression Current Level . . 368, 436
H5-03 . . . . . . . . . . . . . . . . . . . . . . 350, 410, 442 Hunting Prevention Gain . . . . . . . . . . . . . . . . 177
H5-04 . . . . . . . . . . . . . . . . . . . . . . 350, 410, 442 Hunting Prevention Gain Setting. .237, 366, 435
H5-05 . . . . . . . . . . . . . . . . . . . . . . 350, 411, 442 Hunting Prevention Gain while in Reverse . .366,
H5-06 . . . . . . . . . . . . . . . . . . . . . . 350, 411, 442 435
H5-07 . . . . . . . . . . . . . . . . . . . . . . 350, 411, 442 Hunting Prevention Selection . . . . . . . . 366, 435
H5-09 . . . . . . . . . . . . . . . . . . . . . . 208, 350, 442 Hunting Prevention Time Constant . . . . 366, 435
H5-10 . . . . . . . . . . . . . . . . . . . . . . . . . . 351, 442
H5-11 . . . . . . . . . . . . . . . . . . . . . . . . . . 351, 442
I
H5-12 . . . . . . . . . . . . . . . . . . . . . . . . . . 351, 442 I/O Connections . . . . . . . . . . . . . . . . . . . . . . . . 77
H6 Pulse Train Input/Output. . . . . . . . . . . . . . 351 IGBT Maintenance . . . . . . . . . . . .151, 383, 441
H6-01 . . . . . . . . . . . . . . . . . . . . . . . . . . 351, 442 IGBT Maintenance Setting . . . . . . . . . . 372, 437
H6-02 . . . . . . . . . . . . . . . . . .200, 213, 351, 442 Initial Operation. . . . . . . . . . . . . . . . . . . . . . . 106
H6-02 through H6-05 . . . . . . . . . . . . . . 200, 213 Initialize Parameters . . . . . . 112, 122, 311, 433
H6-03 . . . . . . . . . . . . . . . . . . . . . . . . . . 351, 442 Input Fuses. . . . . . . . . . . . . . . . . . . . . . . 418, 426
H6-04 . . . . . . . . . . . . . . . . . . . . . . . . . . 351, 442 Input Phase Loss . . . . . . . . . . . . . . . . . . 183, 201
H6-06 . . . . . . . . . . . . . . . . . . . . . . . . . . 351, 442 Input Phase Loss Protection Selection. . 364, 435
H6-07 . . . . . . . . . . . . . . . . . . . . . . . . . . 352, 442 Input Pulse Monitor . . . . . . . . . . . .151, 380, 439
Hardwire Baseblock . . . . . . . . . . . . . . . . . . . . . 70 Input Terminal Status. . . . . . . . . . .151, 378, 439
Hbb . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184, 210 Input Terminal Status at Previous Fault 151, 381,
HbbF . . . . . . . . . . . . . . . . . . . . . . . . . . . 184, 211 440
HCA . . . . . . . . . . . . . . . . . . . . . . . . . . . 185, 211 Input Terminals . . . . . . . . . . . . . . . . . . . . . . . 104
Heatsink Cooling Fan Operation Delay Time364, Input Voltage Setting . . . . . . . . . . .138, 330, 438
435 Inrush Prevention Circuit Fault . . . . . . . . . . . 205
Heatsink Cooling Fan Operation Selection . 364, Inrush Prevention Relay Maintenance Setting372,
435 437
Heatsink Overheat . . . . . . . .183, 185, 196, 211 Inspection. . . . . . . . . . . . . . . 247, 248, 249, 250
Heavy Duty Ratings . . . . . . . . . . . . . . . . . . . . 292 Installation Environment . . . . . . . . . . . . . . . . . 41
Heavy Load Current Level (for PM) . . . . . . . 436 Installation Orientation . . . . . . . . . . . . . . . . . . 42
High Performance Control Selection . . . . . . . 436 Installation Spacing . . . . . . . . . . . . . . . . . . . . . 42
High Slip Braking . . . . . . . . . . . . . . . . . . . . . . 344 Installing Multiple Drives . . . . . . . . . . . . . . . . 43
High Slip Braking OL. . . . . . . . . . . . . . . . . . . 183 Integral Limit Setting. . . . . . . . . . . . . . . 316, 434
High Starting Torque . . . . . . . . . . . . . . . . . . . 142 Integral Time Setting (I) . . . . . . . . . . . . 316, 434
High-slip Braking . . . . . . . . . . . . . . . . . . . . . . 200 Internal Dynamic Braking Resistor Protection 83
High-Slip Braking Current Limit . . . . . 367, 436 Internal Dynamic Braking Resistor Protection
High-Slip Braking Deceleration Frequency Width Selection (ERF type) . . . . . . . . . . . . . . . 363, 435
367, 436 Inverter Duty motor . . . . . . . . . . . . . . . . . . . . 148

452 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
J L3-01 through L3-06 . . . . . . . . . . . . . . . . . . . 180
Jog Frequency Reference . . . . . . . 166, 326, 437 L3-02 . . . . . . . . . . . . . . . . . . 233, 239, 355, 433
L3-03 . . . . . . . . . . . . . . . . . . . . . . . . . . . 355, 433
Jog Function . . . . . . . . . . . . . . . . . . . . . . . . . . 166
L3-04 . . . . . . . . . . .83, 198, 200, 235, 356, 433
Jog Operation . . . . . . . . . . . . . . . . . . . . . . . . . 166
Jog Reference Selection . . . . . . . . . . . . . . . . . 341 L3-05 . . . . . . . . . . . . . . . . . . . . . . . . . . . 356, 433
L3-06 . . . . . . . . . . . . . . . . . . 180, 234, 356, 433
Jump Frequency . . . . . . . . . . . . . . . . . . . . . . . 180
L3-07 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180
Jump Frequency 1. . . . . . . . . . . . . . . . . .327, 437
Jump Frequency 2. . . . . . . . . . . . . . . . . .327, 438 L3-11 . . . . . . . . . . . . . . . . . . 180, 201, 357, 433
L3-17 . . . . . . . . . . . . . . . . . . . . . . . . . . . 357, 433
Jump Frequency 3. . . . . . . . . . . . . . . . . .327, 438
L3-20 . . . . . . . . . . . . . . . . . . . . . . . . . . . 357, 433
Jump Frequency Width. . . . . . . . . . . . . .327, 438
L3-21 . . . . . . . . . . . . . . . . . . . . . . . . . . . 357, 434
K L3-22 . . . . . . . . . . . . . . . . . . . . . . . . . . . 357, 434
KEB Deceleration Time . . . . . . . . . . . . .354, 433 L3-23 . . . . . . . . . . . . . . . . . . . . . . . . . . . 357, 434
KEB Operation . . . . . . . . . . . . . . . . . . . . . . . . 347 L3-24 . . . . . . . . . . . . . . . . . . . . . . . . . . . 358, 434
KEB Ride-thru (N.C.). . . . . . . . . . . . . . . . . . . 344 L3-25 . . . . . . . . . . . . . . . . . . . . . . .201, 358, 434
KEB Ride-thru (N.O.) . . . . . . . . . . . . . . . . . . 344 L4 Frequency Detection . . . . . . . . . . . . . . . . 358
KEB Ride-thru 2 (N.C.) . . . . . . . . . . . . . . . . . 344 L4-01 . . . . . . . . . . . . . . . . . . . . . . .236, 358, 434
KEB Ride-thru 2 (N.O.) . . . . . . . . . . . . . . . . . 344 L4-02 . . . . . . . . . . . . . . . . . . . . . . .236, 358, 434
kWH Monitor Initial Value Selection. . .372, 437 L4-03 . . . . . . . . . . . . . . . . . . . . . . . . . . . 358, 434
kWH, Lower 4 Digits . . . . . . . . . . 151, 384, 441 L4-04 . . . . . . . . . . . . . . . . . . . . . . . . . . . 358, 434
kWH, Upper 5 Digits . . . . . . . . . . 151, 384, 441 L4-05 . . . . . . . . . . . . . . . . . . . . . . . . . . . 358, 434
L4-06 . . . . . . . . . . . . . . . . . . . . . . . . . . . 358, 434
L L5 Fault Reset . . . . . . . . . . . . . . . . . . . . . . . . 359
L Protection Function . . . . . . . . . . . . . . .352, 373 L5-01 . . . . . . . . . . . . . . . . . . . . . . .214, 359, 434
L1 Motor Protection Functions . . . . . . . . . . . 352 L5-02 . . . . . . . . . . . . . . . . . . . . . . . . . . . 359, 434
L1-01 147, 148, 149, 198, 352, 428, 429, 442 L5-04 . . . . . . . . . . . . . . . . . . . . . . . . . . . 359, 434
L1-02 . . . . . . . . . . . . . . . . . . 147, 353, 429, 442 L5-05 . . . . . . . . . . . . . . . . . . . . . . . . . . . 359, 434
L1-03 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 353 L6 Overtorque Detection. . . . . . . . . . . . . . . . 360
L1-04 . . . . . . . . . . . . . . . . . . . . . . . . . . .353, 433 L6-01 . . . . . . . . . . . . . . . . . . . . . . . . . . . 360, 434
L1-05 . . . . . . . . . . . . . . . . . . . . . . . . . . .353, 433 L6-02 . . . . . . . . . . . . . . 199, 203, 213, 360, 434
L2 Momentary Power Loss . . . . . . . . . . . . . . 353 L6-02 and L6-03 . . . . . . . . . . . . . . . . . . 203, 215
L2-01 . . . . . . . . . . . . . . . . . . . . . . . . . . .353, 433 L6-03 . . . . . . . . . . . . . . 199, 203, 213, 360, 434
L2-02 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 353 L6-04 . . . . . . . . . . . . . . . . . . . . . . . . . . . 361, 434
L2-03 . . . . . . . . . . . . . . . . . . . . . . 130, 354, 433 L6-05 . . . . . . . . . . . . . . 199, 204, 213, 361, 434
L2-04 . . . . . . . . . . . . . . . . . . . . . . . . . . .354, 433 L6-05 and L6-06 . . . . . . . . . . . . . .204, 213, 215
L2-05 . . . . . . . . . . . . . . . . . . . . . . 204, 354, 433 L6-06 . . . . . . . . . . . . . . 199, 204, 213, 361, 434
L2-06 . . . . . . . . . . . . . . . . . . . . . . . . . . .354, 433 L6-08 . . . . . . . . . . . . . . . . . . . . . . . . . . . 362, 434
L2-07 . . . . . . . . . . . . . . . . . . . . . . . . . . .354, 433 L6-09 . . . . . . . . . . . . . . . . . . . . . . . . . . . 362, 434
L2-08 . . . . . . . . . . . . . . . . . . . . . . . . . . .354, 433 L6-10 . . . . . . . . . . . . . . . . . . . . . . . . . . . 362, 434
L3 Stall Prevention Function . . . . . . . . . . . . . 355 L6-11 . . . . . . . . . . . . . . . . . . . . . . . . . . . 362, 434
L3-01 . . . . . . . . . . . . . . . . . . . . . . . . . . .355, 433 L7 Torque Limit . . . . . . . . . . . . . . . . . . . . . . 363

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 453
L7-01. . . . . . . . . . . . . . . . . . . . . . . 224, 363, 434 LOCAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
L7-01 through L3-04 . . . . . . . . . . . . . . . . . . . 180 Local/Remote. . . . . . . . . . . . . . . . . . . . . . . . . 346
L7-01 through L7-04 . . . . . .188, 230, 233, 235 LOCAL/REMOTE Key Function Selection .371,
L7-02. . . . . . . . . . . . . . . . . . . . . . . 224, 363, 434 436
L7-03. . . . . . . . . . . . . . . . . . . . . . . . . . . 363, 434 Local/Remote Run Selection . . . . . . . . . 313, 433
L7-04. . . . . . . . . . . . . . . . . . . . . . . . . . . 363, 434 Local/Remote Selection. . . . . . . . . . . . . . . . . 341
L7-06. . . . . . . . . . . . . . . . . . . . . . . . . . . 363, 435 Loss of Reference . . . . . . . . . . . . . . . . . . . . . 346
L7-07. . . . . . . . . . . . . . . . . . . . . . . . . . . 363, 435 Low Voltage Directive. . . . . . . . . . . . . . . . . . 417
L8 Low Voltage Wiring. . . . . . . . . . . . . . . . . . . . 427
Hardware Protection . . . . . . . . . . . . . . . . 363 M
L8-01. . . . . . . . . . . . . . . . . . . .83, 202, 363, 435
Magnetic Flux Compensation Capacity 314, 315,
L8-02. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196
434
L8-03. . . . . . . . . . . . . . . . . . . . . . . . . . . 364, 435
Main Circuit Connection Diagram . . . . . . 58, 68
L8-04. . . . . . . . . . . . . . . . . . . . . . . . . . . 364, 435
Main Circuit Terminal Functions. . . . . . . . . . . 63
L8-05. . . . . . . . . . . . . . . . . . . . . . . . . . . 201, 202
Main Circuit Terminal Power Supply . . . . . . . 66
L8-07. . . . . . . . . . . . . . . . . . . . . . . 193, 364, 435
Main Circuit Terminal Wiring . . . . . . . . . 68, 425
L8-09. . . . . . . . . . . . . . . . . . . . . . . 193, 364, 435
Main Circuit Terminals Connection . . . . . . . . 58
L8-10. . . . . . . . . . . . . . . . . . . . . . . . . . . 364, 435
Main Frequency Reference . . . . . . . . . . . . . . . 79
L8-11. . . . . . . . . . . . . . . . . . . . . . . . . . . 364, 435
Main Frequency Reference Input . . . . . . . . . . 71
L8-12. . . . . . . . . . . . . . . . . . . . . . . 305, 364, 435
Main Power Circuit Voltage Adjustment Gain357,
L8-15. . . . . . . . . . . . . . . . . . . . . . . . . . . 365, 435
433
L8-18. . . . . . . . . . . . . . . . . . . . . . . . . . . 365, 435
Main/Aux. . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
L8-29. . . . . . . . . . . . . . . . . . . . . . . 306, 365, 435
Maintenance. . . . . . . . . . . . . . . . . . . . . . 252, 253
L8-38. . . . . . . . . . . . . . . . . . . . . . . 239, 365, 435
Master Speed Reference Lower Limit. . 326, 437
L8-41. . . . . . . . . . . . . . . . . . . . . . . . . . . 365, 435
Max Output Frequency (FMAX). . . . . . 331, 438
LCD Contrast . . . . . . . . . . . . . . . . . . . . . . . . . 436
Max Voltage (VMAX). . . . . . . . . . . . . . 331, 438
LED Check . . . . . . . . . . . . . . . . . . 151, 384, 441
Mechanical Weakening (N.O.) . . . . . . . . . . . 347
LED Operator . . . . . . . . . . . . . . .91, 92, 93, 127
Mechanical Weakening Detection Operation 362,
LF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182, 193
434
LF2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183, 194
Mechanical Weakening Detection Speed Level .
Line-to-Line Motor Resistance Online Tuning . .
362, 434
368, 436
Mechanical Weakening Detection Start Time362,
Line-to-Line Resistance Auto-Tuning . . . . . . 230
434
Line-to-Line Resistance Error . . . . . . . 186, 223
Mechanical Weakening Detection Time 362, 434
LO/RE. . . . . . . . . . . . . . . . . . . . . . . 94, 104, 162
MEMOBUS/Modbus Communication Error.182,
Load Current. . . . . . . . . . . . . . . . . . . . . 368, 436
184, 187, 207
Load Falls When Brake is Applied (Hoist-Type
MEMOBUS/Modbus Communication Set-up 406
Applications). . . . . . . . . . . . . . . . . . . . . . . . . . 236
MEMOBUS/Modbus Communications Reference
Load Inertia. . . . . . . . . . . . . . . . . . . . . . 369, 436
151, 385, 442
Load Inertia for PM . . . . . . . . . . . . . . . . . . . . 203
MEMOBUS/Modbus Communications Test Mode
Load Inertia Ratio . . . . . . . . . . . . . 201, 358, 434

454 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
Complete. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 214 Motor 2 Mid Output Frequency 2 . . . . . 333, 439
MEMOBUS/Modbus Error Code. . . . . . . . . . 151 Motor 2 Mid Output Frequency Voltage (VC)333,
Memobus/Modbus Error Code . . . . . . . .380, 439 439
MEMOBUS/Modbus Switch Settings . . .81, 407 Motor 2 Mid Output Frequency Voltage 2 . . 333,
MEMOBUS/Modbus Termination . . . . . . . . . . 81 439
MEMOBUS/Modbus Test Mode Complete . . 185 Motor 2 Minimum Output Frequency (FB) . 333,
Mid Output Frequency (FB). . . . . . . . . .331, 438 439
Mid Output Frequency 2 . . . . . . . . . . . .331, 438 Motor 2 Minimum Output Frequency (FMIN) . .
Mid Output Frequency Voltage (VC) . . .331, 438 333, 439
Mid Output Frequency Voltage 2 . . . . . .331, 438 Motor 2 Minimum Output Frequency Voltage
Mid Output Voltage A . . . . . . . . . . . . . .177, 179 (VMIN) . . . . . . . . . . . . . . . . . . . . . . . . . 333, 439
Minimum Frequency Gain at KEB Start . . . . 354 Motor 2 Motor Iron-Core Saturation Coefficient 1
Minimum Output Frequency . . . . . . . . . . . . . 240 334, 439
Minimum Output Frequency (FMIN) . .331, 438 Motor 2 Motor Iron-Core Saturation Coefficient 2
Minimum Output Frequency Voltage (VMIN) . 334, 439
331, 438 Motor 2 Motor Poles . . . . . . . . . . . . . . . 334, 439
Minimum Output Voltage. . . . . . . . . . . .177, 179 Motor 2 Rated Capacity . . . . . . . . . . . . 334, 440
Minor Alarms . . . . . . . . . . . . . . . . . . . . . . . . . 184 Motor 2 Rated Current . . . . . . . . .147, 333, 439
Minor Fault. . . . . . . . . . . . . . . . . . . . . . . . . . . 222 Motor 2 Rated No-Load Current . . . . . . 333, 439
Minor Faults . . . . . . . . . . . . . . . . . . . . . .181, 184 Motor 2 Rated Slip . . . . . . . . . . . . . . . . 333, 439
Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97 Motor 2 Selection . . . . . . . . . . . . . . . . . 342, 347
Momentary Power Loss Minimum Baseblock Motor 2 Torque Compensation Gain. . . 334, 440
Time . . . . . . . . . . . . . . . . . . . . . . . . . . . .354, 433 Motor Acceleration Time for Inertia Calculations
Momentary Power Loss Operation Selection 353, 358, 434
433 Motor Armature Resistance (for PM motor). 335,
Momentary Power Loss Ride-thru Time353, 354, 440
433 Motor Base Frequency . . . . 159, 160, 376, 439
Momentary Power Loss Voltage Recovery Ramp Motor Base Speed . . . . . . . . . . . . .160, 376, 439
Time . . . . . . . . . . . . . . . . . . . . . . . . . . . .354, 433 Motor d Axis Inductance (for PM motor)335, 440
Monitor Output. . . . . . . . . . . . . . . . . . . . . . . . . 71 Motor Data Error . . . . . . . . . . . . . . . . . . 186, 222
Most Recent Fault. . . . . . . . . . . . . 152, 381, 440 Motor Data for Auto-Tuning . . . . . . . . . . . . . 160
Motor 2 Base Frequency (FA) . . . . . . . .333, 439 Motor d-Axis Current at Previous Fault152, 381,
Motor 2 Base Voltage (VBASE) . . . . . .333, 439 440
Motor 2 Control Method Selection. . . . . . . . . 439 Motor Direction at Power Up when Using Operator
Motor 2 Iron Loss. . . . . . . . . . . . . . . . . .334, 440 371, 437
Motor 2 Iron-Core Saturation Coefficient 3 . 334, Motor Does Not Operate When an External Run
440 Command is Input . . . . . . . . . . . . . . . . . . . . . 240
Motor 2 Leakage Inductance . . . . . . . . .334, 439 Motor Does Not Operate When the RUN Button on
Motor 2 Line-to-Line Resistance . . . . . .334, 439 the Digital Operator is Pressed . . . . . . . . . . . 239
Motor 2 Max Voltage (VMAX) . . . . . . .333, 439 Motor Does Not Rotate . . . . . . . . . . . . . . . . . 228
Motor 2 Mechanical Loss. . . . . . . . . . . .334, 440 Motor Excitation Current (ld) . . . .151, 386, 442

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 455
Motor Hunting and Oscillation Control Parameters 442
180 Motor Parameters . . . . . . . . . . . . . . . . . . . . . 142
Motor Hunting Occurs at Low Speeds . . . . . . 232 Motor Poles . . . . . . . . . . . . . . . . . . . . . . . . . . 159
Motor Hunting Occurs When Operating With a Motor Poles (for PM motor) . . . . . . . . . 335, 440
Light Load . . . . . . . . . . . . . . . . . . . . . . . . . . . 235 Motor Produces Insufficient Torque . . . . . . . 238
Motor Induction Voltage Constant 1 (for PM Motor Protection Function. . . . . . . . . . . . . . . 198
motor) . . . . . . . . . . . . . . . . . . . . . . . . . . 336, 440 Motor protection operation time . . . . . . . . . . 149
Motor Induction Voltage Parameter 2 (for PM Motor q Axis Inductance (for PM motor) . . . 440
motor) . . . . . . . . . . . . . . . . . . . . . . . . . . 336, 440 Motor q-Axis Current at Previous Fault151, 381,
Motor Iron Core Saturation Coefficient Error 186 440
Motor Iron Loss . . . . . . . . . . . . . . 161, 376, 439 Motor r/min Reset . . . . . . . . . . . . . . . . . . . . . 437
Motor Iron Loss for Torque Compensation . 143, Motor Rated Capacity (for PM motor) . 335, 440
332, 439 Motor Rated Current . 143, 147, 159, 160, 331,
Motor Iron-Core Saturation Coefficient . . . . . 224 376, 428, 438
Motor Iron-Core Saturation Coefficient 1 . . 143, Motor Rated Current (for PM motor) . . 335, 440
332, 439 Motor Rated Output. . . . . . . . . . . .143, 332, 439
Motor Iron-Core Saturation Coefficient 2 . . 143, Motor Rated Power . . . . . . . . . . . .160, 375, 438
332, 439 Motor Rated Slip . . . . . . . . . . . . . .143, 331, 438
Motor Iron-Core Saturation Coefficient 3332, 439 Motor Rated Voltage . . . . . . 159, 160, 375, 438
Motor Iron-Core Saturation Coefficients . . . . 143 Motor Rotates After the Drive Output is Shut Off
Motor is Too Hot . . . . . . . . . . . . . . . . . . . . . . 231 238
Motor Leakage Inductance . . . . . . 143, 332, 439 Motor Rotates Faster Than the Frequency
Motor Line-to-Line Resistance. . . 143, 332, 439 Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . 234
Motor Mechanical Loss . . . . . . . . 143, 332, 439 Motor Rotates in One Direction Only . . 231, 240
Motor No-Load Current . . . . . . . . 143, 331, 438 Motor Secondary Current (Iq) . . . .151, 386, 442
Motor Operates at a Higher Speed than the Speed Motor Selection 1/2 . . . . . . . . . . . .160, 375, 438
Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . 241 Motor Speed . . . . . . . . . . . . . . . . .150, 377, 439
Motor Overheat. . . . . . . . . . . . . . . . . . . 185, 212 Motor Speed at Previous Fault . . .151, 381, 440
Motor Overheat 1 (PTC input) . . . . . . . . . . . . 183 Motor Speed Error . . . . . . . . . . . . . . . . . . . . . 186
Motor Overheat 2 (PTC input) . . . . . . . . . . . . 183 Motor Speed Fault . . . . . . . . . . . . . . . . . . . . . 224
Motor Overheat Alarm (PTC Input) . . . . . . . . 197 Motor Stalls During Acceleration or With Large
Motor Overheat Alarm Operation Selection (PTC Loads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 233
input). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 353 Motor Stops During Acceleration or When a Load
Motor Overheat Fault (PTC Input) . . . . . . . . . 197 is Connected . . . . . . . . . . . . . . . . . . . . . . . . . 240
Motor Overheat Fault Operation Selection (PTC Motor Switch during Run . . . . . . . . . . . . . . . 214
input). . . . . . . . . . . . . . . . . . . . . . . . . . . 353, 433 Motor Temperature (PTC input) . . . . . . . . . . 349
Motor Overload . . . . . . . . . . . . . . . . . . 183, 197 Motor Temperature Input Filter Time (PTC input)
Motor Overload Estimate (OL1) . 151, 384, 441 353, 433
Motor Overload Protection Selection . . 147, 352, Motor Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . 66
428, 442 Multi-Function Analog 1 (Terminal AM Monitor
Motor Overload Protection Time 147, 353, 429, Selection) . . . . . . . . . . . . . . . . . . . .145, 349, 442

456 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
Multi-Function Analog 1 (Terminal AM Output n1-05 . . . . . . . . . . . . . . . . . . . . . . . . . . . 366, 435
Bias) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 442 n2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178
Multi-Function Analog 1 (Terminal AM Output n2 Speed Feedback Detection Control Function .
Gain) . . . . . . . . . . . . . . . . . . . . . . . 145, 349, 442 367
Multi-Function Analog Input Selection Error186, n2-01 . . . . . . . . . . . . . . 178, 235, 237, 367, 435
219 n2-02 . . . . . 178, 201, 220, 232, 235, 367, 435
Multi-Function Analog Outputs . . . . . . . . . . . 144 n2-03 . . . . . . . . . .178, 201, 220, 232, 367, 435
Multi-Function Contact Input. . . . . . . . . . . . . 168 n3 High Slip Braking. . . . . . . . . . . . . . . . . . . 367
Multi-Function Contact Input Terminals . . . . 166 n3-01 . . . . . . . . . . . . . . . . . . . . . . . . . . . 367, 436
Multi-Function Contact Output . . . . . . . . . . . 144 n3-02 . . . . . . . . . . . . . . . . . . . . . . . . . . . 367, 436
Multi-Function Contact Outputs. . . . . . . . . . . 147 n3-03 . . . . . . . . . . . . . . . . . . . . . . . . . . . 367, 436
Multi-Function Digital Input Terminal S1 Function n3-04 . . . . . . . . . . . . . . . . . . 199, 200, 367, 436
Selection . . . . . . . . . . . . . . . . . . . . . . . . .341, 441 n3-13 . . . . . . . . . . . . . . . . . . 195, 198, 368, 436
Multi-Function Digital Input Terminal S2 Function n3-21 . . . . . . . . . . . . . . . . . . . . . . . . . . . 368, 436
Selection . . . . . . . . . . . . . . . . . . . . . . . . .341, 441 n3-23 . . . . . . . . . . . . . . . . . . . . . . .198, 368, 436
Multi-Function Digital Input Terminal S3 Function n6 Online Tuning of Resistance between Motor
Selection . . . . . . . . . . . . . . . . . . . . . . . . .341, 441 Lines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 368
Multi-Function Digital Input Terminal S4 Function n6-01 . . . . . . . . . . . . . . . . . . . . . . . . . . . 368, 436
Selection . . . . . . . . . . . . . . . . . . . . . . . . .341, 441 n8 Permanent Magnet (PM) Motor Control . 368
Multi-Function Digital Input Terminal S5 Function n8-45 . . . . . . . . . . . . . . . . . . 201, 239, 368, 436
Selection . . . . . . . . . . . . . . . . . . . . . . . . .341, 441 n8-47 . . . . . . . . . . . . . . 201, 239, 368, 369, 436
Multi-Function Digital Input Terminal S6 Function n8-48 . . . . . . . . . . . . . . . . . . . . . . . . . . . 368, 436
Selection . . . . . . . . . . . . . . . . . . . . . . . . .341, 441 n8-49 . . . . . . . . . . . . . . . . . . . . . . . . . . . 368, 436
Multi-Function Digital Input Terminal S7 Function n8-50 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 436
Selection . . . . . . . . . . . . . . . . . . . . . . . . .341, 441 n8-51 . . . . . . . . . . . . . . . . . . . . . . .203, 369, 436
Multi-Function Digital Inputs. . . . . . . . . . . . . . 70 n8-55 . . . . . . . . . . . . . . . . . . . . . . .203, 369, 436
Multi-Function Digital Output . . . . . . . . . . . . . 71 n8-56 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 436
Multi-Function Input Selection Error. . . . . . . 217 NEMA Type 1 . . . . . . . . . . . . . . . . . . .47, 48, 49
Multi-Function Input Setting Error . . . . . . . . 185 Noise From the Drive or Output Lines When the
Multi-Function Photocoupler Output . . . . . . . . 71 Drive is Powered On . . . . . . . . . . . . . . . . . . . 236
Multiple Drive Wiring . . . . . . . . . . . . . . . . . . . 68 No-Load Current Error . . . . . . . . . . . . . 186, 223
Multi-Step Speed Operation (4-Step Speed) . 168 No-Load Operation . . . . . . . . . . . . . . . . . . . . 161
Multi-Step Speed Reference. . . . . . . . . . . . . . 341 Normal Duty Ratings. . . . . . . . . . . . . . . . . . . 292
Multi-Step Speed Reference 4 . . . . . . . . . . . . 343 Number of Auto Restart Attempts. . . . . 359, 434
Number of Motor Poles143, 160, 332, 376, 438,
N 439
n Advanced Performance Set Up . . . . . . . . . . 366 Number of Run Commands. . . . . .151, 383, 441
n1 Hunting Prevention . . . . . . . . . . . . . . . . . . 366 Number of Speed Search Restarts . . . . . 316, 434
n1-01. . . . . . . . . . . . . . . . . . . . . . . 235, 366, 435
n1-02. . . . . . . . . . . . . . 177, 201, 237, 366, 435 O
n1-03. . . . . . . . . . . . . . . . . . . . . . . . . . . .366, 435 o Operator Related Parameters . . . . . . . . . . . 370

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 457
o1 Display Settings . . . . . . . . . . . . . . . . . . . . . 370 oH1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183, 196
o1-03 . . . . . . . . . . . . . . . . . . . . . . . . . . . 370, 436 oH2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185, 212
o1-10 . . . . . . . . . . . . . . . . . . . . . . . . . . . 370, 436 oH3 . . . . . . . . . . . . . . . . . . . 183, 185, 197, 212
o1-11 . . . . . . . . . . . . . . . . . . . . . . . . . . . 370, 436 oH4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183, 197
o2 Multi-Function Selections . . . . . . . . . . . . . 371 oL1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183, 197
o2-01 . . . . . . . . . . . . . . . . . . . . . . . 229, 371, 436 oL2. . . . . . . . . . . . . . . . . . . . . . . . .183, 198, 239
o2-02 . . . . . . . . . . . . . . . . . . . . . . . 230, 371, 436 OL2 Characteristics Selection at Low Speeds365,
o2-03 . . . . . . . . . . . . . . 113, 122, 164, 371, 436 435
o2-04 . . . . . . . . . . . . . . 177, 196, 217, 371, 436 oL3. . . . . . . . . . . . . . . . . . . . 183, 185, 199, 213
o2-05 . . . . . . . . . . . . . . . . . . . . . . . . . . . 371, 437 oL4. . . . . . . . . . . . . . . . . . . . 183, 185, 199, 213
o2-06 . . . . . . . . . . . . . . . . . . . . . . . 200, 371, 437 oL7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183, 199
o2-07 . . . . . . . . . . . . . . . . . . . . . . . . . . . 371, 437 OPE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217
o3-01 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 437 oPE Fault . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151
o3-02 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 437 OPE fault constant . . . . . . . . . . . . . . . . . . . . . 217
o3-03 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 437 OPE Fault Parameter . . . . . . . . . . . . . . . 379, 439
o4 Maintenance Period . . . . . . . . . . . . . . . . . . 372 oPE01. . . . . . . . . . . . . . . . . . . . . . . . . . . 185, 217
o4-01 . . . . . . . . . . . . . . . . . . . . . . . . . . . 372, 437 oPE02. . . . . . . . . . . . . . . . . . . . . . . . . . . 185, 217
o4-02 . . . . . . . . . . . . . . . . . . . . . . . . . . . 372, 437 oPE03. . . . . . . . . . . . . . . . . . . . . . .185, 217, 218
o4-03 . . . . . . . . . . . . . . 196, 197, 212, 372, 437 oPE05. . . . . . . . . . . . . . . . . . . . . . . . . . . 186, 219
o4-05 . . . . . . . . . . . . . . . . . . . . . . . . . . . 372, 437 oPE07. . . . . . . . . . . . . . . . . . . . . . . . . . . 186, 219
o4-07 . . . . . . . . . . . . . . . . . . . . . . . . . . . 372, 437 oPE08. . . . . . . . . . . . . . . . . . . . . . . . . . . 185, 220
o4-09 . . . . . . . . . . . . . . . . . . . . . . . . . . . 372, 437 oPE09. . . . . . . . . . . . . . . . . . . . . . . . . . . 185, 220
o4-10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 437 oPE10. . . . . . . . . . . . . . . . . . . . . . . . . . . 185, 220
o4-11 . . . . . . . . . . . . . . . . . . . . . . . . . . . 372, 437 oPE11. . . . . . . . . . . . . . . . . . . . . . . . . . . 186, 221
o4-12 . . . . . . . . . . . . . . . . . . . . . . . . . . . 372, 437 Open Loop Vector . . . . . . . . . . . . . . . . . . . . . 224
o4-13 . . . . . . . . . . . . . . . . . . . . . . . . . . . 372, 437 Open Loop Vector Control 109, 122, 142, 156,
oC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183, 194 179, 188, 201, 230, 232, 233, 234, 237, 238
oFA00 . . . . . . . . . . . . . . . . . . . . . . . . . . 183, 195 Open Loop Vector Control Mode Tuning . . . 178
oFA01 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195 Open Loop Vector Control Mode Tuning
oFA03 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196 Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . 178
oFA04 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196 Open-Chassis IP20 . . . . . . . . . . . . . . . . . . 45, 46
Offset Frequency. . . . . . . . . . . . . . 152, 387, 442 Operating with the Load Connected . . . . . . . 163
Offset Frequency 1 . . . . . . . . . . . . . . . . 329, 438 Operation Errors . . . . . . . . . . . . . . . . . . 181, 185
Offset Frequency 1 Addition . . . . . . . . . . . . . 343 Operation Selection at Deviation (for Simple PG
Offset Frequency 2 . . . . . . . . . . . . . . . . 329, 438 V/f Control) . . . . . . . . . . . . . . . . . . . . . . 337, 440
Offset Frequency 2 Addition . . . . . . . . . . . . . 343 Operation Selection at Overspeed (OS) (for Simple
Offset Frequency 3 . . . . . . . . . . . . . . . . 329, 438 PG V/f) . . . . . . . . . . . . . . . . . . . . . . . . . 337, 440
Offset Frequency 3 Addition . . . . . . . . . . . . . 343 Operation Selection at PG Open Circuit (PGO) .
oH . . . . . . . . . . . . . . . . . . . . .183, 185, 196, 211 337, 440
OH Pre alarm . . . . . . . . . . . . . . . . . . . . . . . . . 347 Operation Selection when Digital Operator is
OH Pre-alarm Time Limit. . . . . . . . . . . . . . . . 347 Disconnected . . . . . . . . . . . . . . . . . . . . . 371, 437

458 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
Operator Connection Fault . . . . . . . . . . . . . . . 183 Output voltage reference (Vq). . . .152, 386, 442
Operator Programming Errors . . . . . . . . . . . . 217 ov . . . . . . . . . . . . . . . . . . . . . 183, 185, 200, 213
oPr. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .183, 200 OV Occurs When Starting a Fan or Motor Speed
Option Card Communications Error . . . . . . . 184 Loss Occurs . . . . . . . . . . . . . . . . . . . . . . . . . . 238
Option Card External Fault . 182, 184, 191, 209 OV Suppression Function Selection . . . 357, 433
Option Card Fault (Port A). . . . . . . . . . . . . . . 195 Overcurrent . . . . . . . . . . . . . . . . . . . . . . 183, 194
Option Card Fault (port A) . . . . . . . . . . .183, 196 Overexcitation Deceleration Gain .195, 368, 436
Option Card Reference . . . . . . . . . 151, 385, 442 Overexcitation Operation Selection . . . 368, 436
Option Communication Error. . . . 182, 187, 206 Overheat 1 (Heatsink Overheat) . . . . . . . . . . 196
Option Frequency Reference . . . . 151, 384, 442 Overheat Alarm Level . . . . . . . . . . . . . . 363, 435
Option Reference . . . . . . . . . . . . . . . . . . . . . . 346 Overheat Pre-Alarm Operation Selection364, 435
Option/Drive Selection. . . . . . . . . . . . . . . . . . 341 Overload OL1 (OL1 Alarm) . . . . . . . . . . . . . 347
oS . . . . . . . . . . . . . . . . . . . . . 183, 185, 200, 213 Overspeed (for Simple V/f with PG). . 183, 185,
Oscillation or Hunting . . . . . . . . . . . . . . . . . . 237 213
Output Current . . . . . . . . . . . . . . . 150, 377, 439 Overspeed (Simple V/f with PG) . . . . . . . . . 200
Output Current at Previous Fault . 151, 380, 440 Overspeed Detection Delay Time (for Simple PG
Output current imbalance . . . . . . . . . . . . . . . . 194 V/f Control) . . . . . . . . . . . . . . . . . . . . . . . . . . 440
Output Frequency . . . . . . . . . . . . . 150, 376, 439 Overspeed Detection Level (for Simple PG V/f
Output Frequency after Soft Start. . . . . .379, 439 Control) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 440
Output Frequency after SoftStart . . . . . . . . . . 151 Overtorque 1 . . . . . . . . . . . . . . . . . . . . . 185, 213
Output Frequency at Previous Fault151, 380, 440 Overtorque 2 . . . . . . . . . . . . . . . . . . . . . 185, 213
Output Frequency is not as High as Frequency Overtorque Detection 1 . . . . . . . . . . . . . 183, 199
Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . 239 Overtorque Detection 2 . . . . . . . . . . . . . 183, 199
Output Ground Fault Detection Selection364, 435 Overtorque/Undertorque Detection Level. . . 349
Output of speed control (ASR) (for Simple V/f PG) Overvoltage . . . . . . . . . . . . . . . . . .183, 185, 200
151, 386, 442 Overvoltage Occurs When Running at a Constant
Output Open Phase . . . . . . . . . . . . . . . . . . . . . 183 Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 232
Output Phase Loss . . . . . . . . . . . . . . . . .182, 193 Overvoltage Suppression. . . . . . . . . . . . . . . . 201
Output Phase Loss Protection. . . . . . . . .364, 435 Overvoltage Suppression and Deceleration Stall
Output Power . . . . . . . . . . . . . . . . 151, 377, 439 (Desired DC Bus Voltage during Motor Stall) 433
Output Power at Previous Fault . . 151, 381, 440
Output Terminal Status. . . . . . . . . 151, 378, 439
P
Output Terminal Status at Previous Fault. . . 151, Parameter Range Setting Error . . . . . . . . . . . 217
381, 440 Parameter Selection Error . . . . . . . . . . . 185, 220
Output Voltage at Previous Fault . 151, 381, 440 Parameter Setting Range Error . . . . . . . . . . . 185
Output Voltage Bias . . . . . . . . . . . . . . . . . . . . 349 Parameter Settings. . . . . . . . . . . . . . . . . . . . . 102
Output Voltage Limit Operation Selection . . 322, PASS . . . . . . . . . . . . . . . . . . . . . . . . . . . 185, 214
436 Password 1. . . . . . . . . . . . . . . . . . . . . . . . . . . 311
Output Voltage Reference. . . . . . . 150, 377, 439 Password 2. . . . . . . . . . . . . . . . . . . . . . . 311, 433
output voltage reference . . . . . . . . . . . . . . . . . 150 Password Settings . . . . . . . . . . . . . . . . . . . . . 165
Output Voltage Reference (Vd) . . 152, 386, 442 Peak Hold Current . . . . . . . . . . . . . . . . . 151, 384

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 459
Peak Hold Output Frequency . . . . 151, 384, 441 PID Output Reverse Selection . . . . . . . . 317, 434
Performance Life . . . . . . . . . . . . . . . . . . . . . . 252 PID Primary Delay Time Constant . . . . 317, 434
Peripheral Devices Affected by Drive Operation . PID Set Point . . . . . . . . . . . . . . . . . . . . . . . . . 349
241 PID Setpoint . . . . . . . . . . . . . . . . .151, 386, 442
Permanent Magnet Motor Control . . . . . . . . . 110 PID Setpoint / User Display . . . . . . . . . 318, 435
PF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183, 201 PID Setpoint and Display Digits . . . . . . 318, 435
PG Disconnect (for Simple V/f with PG) . . . 183, PID Setpoint Scaling . . . . . . . . . . . . . . . 318, 435
185, 202, 214 PID Setpoint Selection. . . . . . . . . . . . . . 318, 435
PG Open-Circuit Detection Time (for Simple PG PID Setpoint Value . . . . . . . . . . . . . . . . 318, 435
V/f Control) . . . . . . . . . . . . . . . . . . . . . 338, 440 PID Sleep Delay Time . . . . . . . . . . . . . . 318, 435
PGo . . . . . . . . . . . . . . . . . . . .183, 185, 202, 214 PID Sleep Function Start Level . . . . . . . 318, 435
Phase Order Selection. . . . . . . . . . . . . . 314, 433 PID Soft Starter . . . . . . . . . . . . . . . . . . . . . . . 343
PID Accel/Decel Time . . . . . . . . . . . . . 318, 435 PM Open Loop Vector Control . . .110, 122, 134
PID Adjusted Feedback . . . . . . . . . . . . 152, 442 PM Speed Feedback Detection Suppression Gain
PID Control Selection Error . . . . . . . . . . . . . . 185 201
PID Control Selection Fault . . . . . . . . . . . . . . 220 Poor Speed Control Accuracy . . . . . . . . . . . . 234
PID Differential Feedback . . . . . . . . . . 152, 442 Poor Speed Control Accuracy Above Base Speed
PID Disable. . . . . . . . . . . . . . . . . . . . . . . . . . . 342 in Open-loop Vector Motor Control Method . 241
PID Feedback . . . . . . . . . . . .151, 349, 386, 442 Power Detection Filter Time . . . . . . . . . 319, 435
PID Feedback Fault . . . . . . . . . . . . . . . . . . . . 347 Power Specifications 200 V Class Models . .293,
PID Feedback High Detection Level . . 318, 435 294, 296, 297
PID Feedback High Level Detection Time. . 318, Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
435 Preferred Parameter Automatic Selection . . . 165
PID Feedback Loss . . . 182, 184, 193, 210, 347 Preferred Parameters . . . . . . . . . . . . . . . . . . . 165
PID Feedback Loss Detection Level . . 317, 435 Previous Fault . . . . . . . . . . . . . . . .151, 380, 439
PID Feedback Loss Detection Time . . . 317, 435 Program Lockout . . . . . . . . . . . . . . . . . . . . . . 342
PID Feedback Reference Missing Detection Programming Mode . . . . . . . . . . . . . .97, 99, 101
Selection . . . . . . . . . . . . . . . . . . . . . . . . 317, 435 Proportional Gain Setting (P) . . . . . . . . 316, 434
PID Function Setting . . . . . . . . . . . . . . 316, 434 Protective Covers, NEMA Type 1 . . . . . . . . . . 61
PID Input (feedback) . . . . . . . . . . 151, 386, 442 Protective Covers, Open-Chassis . . . . . . . . . . 60
PID Input Limit. . . . . . . . . . . . . . . . . . . 318, 435 Protective Covers, Reattaching . . . . . . . . . . . . 62
PID Input Switch . . . . . . . . . . . . . . . . . . . . . . 343 Protective Covers, Removing . . . . . . . . . . 60, 61
PID Integral Hold . . . . . . . . . . . . . . . . . . . . . . 343 Pull-In Current. . . . . . . . . . . . . . . . . . . . 368, 436
PID Integral Reset. . . . . . . . . . . . . . . . . . . . . . 343 Pull-In Current Compensation Time Constant201,
PID Offset Adjustment . . . . . . . . . . . . . 317, 434 239, 368, 436
PID Output . . . . . . . . . . . . . . . . . . 151, 386, 442 Pull-In Current during Accel/Decel for PM . 203
PID output fault . . . . . . . . . . . . . . . . . . . . . . . 238 Pull-Out Detection . . . . . . . . . . . . . . . . . 183, 203
PID Output Gain Setting. . . . . . . . . . . . 317, 434 Pulse Train Input Bias . . . . . . . . . . . . . . 351, 442
PID Output Level Selection . . . . . . . . . 317, 434 Pulse Train Input Filter Time. . . . . . . . . 351, 442
PID Output Limit . . . . . . . . . . . . . . . . . 317, 434 Pulse Train Input Gain. . . . . . . . . . . . . . 351, 442
PID Output Lower Limit . . . . . . . . . . . 318, 435 Pulse Train Input Scaling. . . 200, 213, 351, 442

460 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
Pulse Train Input . . . . . . . . . . . . . . . . . . . . . . 126 Run Command Selection. . . . . . . .229, 313, 433
Pulse Train Monitor Scaling. . . . . . . . . .352, 442 Run Command Selection during Program. . . 313,
PWM Data Error. . . . . . . . . . . . . . . . . . . . . . . 188 433
PWM Data Fault. . . . . . . . . . . . . . . . . . . . . . . 182 Run Command Selection Error . . . . . . . 186, 219
PWM Feedback Data Fault . . . . . . . . . . . . . . 182 Run Command Selection Results .151, 385, 442
PWM Feedback Fault . . . . . . . . . . . . . . . . . . . 191 Run Command Source 2 . . . . . . . . . . . . 314, 433
rUnC . . . . . . . . . . . . . . . . . . . . . . . . . . . 185, 215
Q
q-axis ACR Output . . . . . . . . . . . . 152, 386, 442 S
S1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
R S2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
RAM Fault . . . . . . . . . . . . . . . . . . . . . . .182, 183 Safety Hazard Definitions . . . . . . . . . . . . . . . . 14
RAM fault. . . . . . . . . . . . . . . . . . . . . . . . . . . . 190 Safety Information. . . . . . . . . . . . . . . . . . . . . . 14
Ramp to Stop . . . . . . . . . . . . . . . . . . . . . . . . . 129 S-Curve Characteristic at Accel End. . . 321, 436
Rated Current Setting Alarm . . . . . . . . .186, 225 S-Curve Characteristic at Accel Start . . 321, 436
Rated Output Operation . . . . . . . . . . . . . . . . . 142 S-Curve Characteristic at Decel End. . . 321, 436
Rated Slip Error . . . . . . . . . . . . . . . . . . .186, 223 S-Curve Characteristic at Decel Start . . 321, 436
Reference Sample Hold . . . . . . . . . . . . . . . . . 342 S-Curve Characteristics. . . . . . . . . . . . . 134, 180
Regenerative Torque Limit. . . . . . . . . . . . . . . 349 Search Operation Voltage Limit . . . . . . 319, 435
REMOTE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103 SEr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183, 203
Replacement Parts . . . . . . . . . . . . 252, 305, 306 Serial Communication Terminals . . . . . . 72, 408
Reset Command Active . . . . . . . . . . . . . . . . . 346 Serial Communication Transmission Error . . 184,
Restart Enabled. . . . . . . . . . . . . . . . . . . . . . . . 347 207
REV Torque Limit . . . . . . . . . . . . . . . . . . . . . 349 Setup Mode . . . . . . . . . . . . . . . . . . . . . . 101, 104
Reverse Direction . . . . . . . . . . . . . . . . . . . . . . 346 Shielded Twisted-Pair Cables . . . . . . . . . . . . . 75
Reverse Jog. . . . . . . . . . . . . . . . . . . . . . . . . . . 342 Short Circuit Brake Time at Start . . . . . 315, 434
Reverse Operation Selection . . . . . . . . . . . . . 313 Short-Circuit Brake . . . . . . . . . . . . . . . . . . . . 347
Reverse Regenerative Torque Limit . . . .363, 434 Short-Circuit Brake (N.C.) . . . . . . . . . . . . . . 344
Reverse Run Command (2-wire sequence) . . 343 Short-Circuit Brake (N.O.) . . . . . . . . . . . . . . 344
Reverse Torque Limit . . . . . . . . . . . . . . .363, 434 Side-by-Side Setup . . . . . . . . . . . . . . . . . . . . . 43
rH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .183, 202 Simple V/f with PG . . . . . . . . . . . . . . . . . . . . 220
Rotational Auto-Tuning . . . . . . . . 154, 156, 230 Sinking/Sourcing Mode Switch. . . . . . . . . . . . 77
rr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .183, 203 Slip Compensation Gain . . . . . . . .179, 321, 436
RTS Control Selection . . . . . . . . . . . . . .350, 442 Slip Compensation Limit. . . . . . . . . . . . 322, 436
rUn . . . . . . . . . . . . . . . . . . . . . . . . . . . . .185, 214 Slip Compensation Primary Delay Time321, 436
Run command. . . . . . . . . . . . . . . . . . . . . . . . . 130 Slip Compensation Primary Delay Time Constant
Run Command (2-wire sequence 2) . . . . . . . . 343 179
Run Command at Power Up. . . . . . . . . .314, 433 Slip Compensation Selection during Regeneration
Run Command Input Error. . . . . . . . . . . . . . . 184 322, 436
Run Command Input Selection . . . . . . . . . . . 127 Soft Charge Circuit Fault . . . . . . . . . . . . . . . 183
Run Command Reset . . . . . . . . . . . . . . . . . . . 185 Soft CLA Selection . . . . . . . . . . . . . . . . 365, 435

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 461
Soft Starter Speed Reference at Previous Fault . . Stall Prevention Selection during Acceleration .
151, 381, 440 355, 433
Software No. (Flash). . . . . . . . . . . . . . . 380, 439 Stall Prevention Selection during Deceleration .
Software No. (ROM) . . . . . . . . . . . . . . 380, 439 356, 433
Software Number (Flash) . . . . . . . . . . . . . . . . 151 Stall Prevention Selection during Run. . 356, 433
Software Number (ROM) . . . . . . . . . . . . . . . . 151 Standard Connection Diagram. . . . . . . . . . 55, 56
Speed Agreement Detection Level . . . . 358, 434 Stationary Auto-Tuning . . . . . . . . . . . . . . . . . 157
Speed Agreement Detection Level (+/-) 358, 434 STO . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183, 203
Speed Agreement Detection Width . . . 358, 434 STOP Button Input . . . . . . . . . . . . . . . . . . . . 222
Speed Agreement Detection Width (+/-)358, 434 STOP button Input. . . . . . . . . . . . . . . . . . . . . 186
Speed Control Integral Time 1 . . . . . . . 200, 213 STOP Key Function Selection. . . . . . . . 371, 436
Speed Control Proportional Gain 1. . . . 200, 213 Stopping Method . . . . . . . . . . . . . . . . . . . . . . 129
Speed Deviation (for Simple V/f with PG). . 191, Stopping Method After Communication Error .
208 350, 442
Speed Estimation Type Speed Search. . . . . . . 201 Stopping Method Selection . . . . . . . . . . 313, 433
Speed Feedback Detection Control (AFR) Gain . Suppression Diode Connection . . . . . . . . . . . . 72
367, 435
Speed Feedback Detection Control (AFR) Time
T
Constant . . . . . . . . . . . . . . . . . . . . . . . . 367, 435 T Motor Tuning . . . . . . . . . . . . . . . . . . . . . . . 375
Speed Feedback Detection Control (AFR) Time T1-00 . . . . . . . . . . . . . . . . . . . . . . .160, 375, 438
Constant 2 . . . . . . . . . . . . . . . . . . . . . . . 367, 435 T1-01 . . . . . . . . . . . . . . . . . . 154, 160, 375, 438
Speed Feedback Detection Control Gain368, 436 T1-02 . . . . . . . . . . . . . . 158, 160, 222, 375, 438
Speed Feedback Detection Suppression Gain 239 T1-03 . . . . . . . . . 159, 160, 161, 224, 375, 438
Speed Search. . . . . . . . . . . . . . . . . . . . . 203, 347 T1-04 . . . . . 159, 160, 161, 222, 225, 376, 438
Speed Search Deactivation Current . . . 315, 434 T1-05 . . . . . 159, 160, 161, 222, 224, 376, 439
Speed Search Deceleration Time . . . . . 315, 434 T1-06 . . . . . . . . . . . . . . . . . . 159, 160, 376, 439
Speed Search Delay Time. . . . . . . . . . . 315, 434 T1-07 . . . . . . . . . . . . . . 159, 160, 222, 376, 439
Speed Search Estimation Type . . . . . . . . . . . . 199 T1-11 . . . . . . . . . . . . . . . . . . . . . . .161, 376, 439
Speed Search Method Selection . . . . . . 316, 434 Terminal A1 Bias Setting. . . . . . . . . . . . 348, 441
Speed Search Restart Current Level . . . 315, 434 Terminal A1 Gain Setting . . . . . . . . . . . 348, 441
Speed Search Restart Detection Time . 316, 434 Terminal A1 Input Voltage . . . . . .151, 379, 439
Speed Search Retry Interval Time . . . . 316, 434 Terminal A1 Signal Level Selection . . . 348, 441
Speed Search Selection. . . . . . . . . . . . . 315, 434 Terminal A2 Enable. . . . . . . . . . . . . . . . . . . . 342
Stall Prevention. . . . . . . . . . . . . . . . . . . 180, 201 Terminal A2 Function Selection . . . . . . 348, 441
Stall Prevention During Deceleration . . . . . . . . 83 Terminal A2 Gain Setting . . . . . . . . . . . . . . . 348
Stall Prevention during Deceleration . . . . . . . 198 Terminal A2 Input Voltage . . . . . .151, 379, 439
Stall Prevention Level during Acceleration . 355, Terminal A2 Signal Level Selection . . . 348, 441
433 Terminal A2 Switch. . . . . . . . . . . . . . . . . . . . . 79
Stall Prevention Level during Run . . . . 356, 433 Terminal AM Bias Setting . . . . . . . . . . . . . . . 145
Stall Prevention Limit during Acceleration . 355, Terminal AM Monitor Selection . . . . . . . . . . 145
433 Terminal Block Configuration. . . . . . . . . . . . . 59

462 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
Terminal Board . . . . . . . . . . . . . . . . . . . . . . . . 258 Torque Detection Time 2. . . . . . . . . . . . 361, 434
Terminal Board Communication Fault. . . . . . 182 Torque Limit Control Method Selection during
Terminal Board Communications Error . . . . . 189 Accel/Decel . . . . . . . . . . . . . . . . . . . . . . 363, 435
Terminal Board Wiring Guide . . . . . . . . . . . . . 75 Torque Limit Integral Time Constant . . 363, 435
Terminal FM Monitor Selection . . . . . . . . . . . 145 Torque Limits . . . . . . . . . . . . . . . . . . . . . . . . 180
Terminal M1 thru M2 Function Selection (relay) Torque Reference . . . . . . . . . . . . .151, 377, 439
144 Torque Reference (Internal) . . . . . . . . . 151, 442
Terminal MA, MB and MC Function Selection Torque Reference at Previous Fault151, 381, 440
(relay) . . . . . . . . . . . . . . . . . . . . . . 144, 345, 441 Torque Specifications, Single Phase 200 V Class
Terminal P1 Function Selection (open-collector) 64
144, 345, 441 Torque Specifications, Three Phase 200 V Class.
Terminal P2 Function Selection (open-collector) 64
144, 345, 441 Torque Specifications, Three Phase 400 V Class.
Test Run . . .153, 155, 156, 157, 158, 159, 162 65
Tightening Torque . . . . . . . . . . . . . . . . . . . . . . 63 Transistor Input Signal . . . . . . . . . . . . . . . 77, 78
Time Constant 1 . . . . . . . . . . . . . . . . . . . . . . . 237 Tuning Errors. . . . . . . . . . . . . . . . . . . . . . . . . 182
Timer Function . . . . . . . . . . . . . . . . . . . . . . . . 342
Timer Function Off-Delay Time. . . . . . .316, 434 U
Timer Function On-Delay Time . . . . . . .316, 434 U Monitors . . . . . . . . . . . . . . . . . . . . . . . . . . 376
Timer Output . . . . . . . . . . . . . . . . . . . . . . . . . 346 U1 Operation Status Monitors. . . . . . . . . . . . 376
Timing Fault . . . . . . . . . . . . . . . . . . . . . .183, 190 U1-01. . . . . . . . . . . . . . 150, 229, 233, 376, 439
Too Many Speed Search Restarts . . . . . .183, 203 U1-02. . . . . . . . . . . . . . . . . . . . . . .150, 376, 439
Torque Compensation at Forward Start .322, 436 U1-03. . . . . . . . . . . . . . . . . . . . . . .150, 377, 439
Torque Compensation at Reverse Start .322, 436 U1-04. . . . . . . . . . . . . . . . . . . . . . .150, 377, 439
Torque Compensation Gain . . . . . 177, 322, 436 U1-05. . . . . . . . . . . . . . . . . . . . . . .150, 377, 439
Torque Compensation Gain - Motor 2 . .334, 440 U1-06. . . . . . . . . . . . . . . . . . . . . . .150, 377, 439
Torque Compensation Primary Delay Time . 177, U1-07. . . . . . . . . . . . . . . . . . 151, 228, 377, 439
237, 239, 322, 436 U1-08. . . . . . . . . . . . . . . . . . . . . . .151, 377, 439
Torque Compensation Primary Delay Time U1-09. . . . . . . . . . . . . . . . . . 151, 229, 377, 439
Constant 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . 178 U1-10. . . . . . . . . . . . . . . . . . . . . . .151, 378, 439
Torque Compensation Primary Delay Time U1-11 . . . . . . . . . . . . . . . . . . . . . . .151, 378, 439
Constant 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . 179 U1-12. . . . . . . . . . . . . . . . . . . . . . .151, 379, 439
Torque Compensation Time Constant . .323, 436 U1-13. . . . . . . . . . . . . . . . . . . . . . .151, 379, 439
Torque Detection 1 (N.O.) . . . . . . . . . . . . . . . 346 U1-14. . . . . . . . . . . . . . . . . . . . . . .151, 379, 439
Torque Detection 2 (N.C.) . . . . . . . . . . . . . . . 346 U1-16. . . . . . . . . . . . . . . . . . . . . . .151, 379, 439
Torque Detection 2 (N.O.) . . . . . . . . . . . . . . . 346 U1-18. . . . . . . . . . . . . . . . . . . . . . .151, 379, 439
Torque Detection Level 1 . . . . . . . . . . . .360, 434 U1-19. . . . . . . . . . . . . . . . . . . . . . .151, 380, 439
Torque Detection Level 2 . . . . . . . . . . . .361, 434 U1-24. . . . . . . . . . . . . . . . . . . . . . .151, 380, 439
Torque Detection Selection 1 . . . . . . . . .360, 434 U1-25. . . . . . . . . . . . . . . . . . . . . . .151, 380, 439
Torque Detection Selection 2 . . . . . . . . .361, 434 U1-26. . . . . . . . . . . . . . . . . . . . . . .151, 380, 439
Torque Detection Time 1 . . . . . . . . . . . .360, 434 U1-34. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 463
U2 Fault Trace . . . . . . . . . . . . . . . . . . . . . . . . 380 U4
U2, U3 Initial Value Selection . . . . . . . 372, 437 Maintenance Monitors . . . . . . . . . . . . . . 383
U2-01 . . . . . . . . . . . . . . . . . . . . . . 151, 380, 439 U4-01 . . . . . . . . . . . . . . . . . . . . . . .151, 383, 441
U2-02 . . . . . . . . . . . . . 151, 226, 227, 380, 439 U4-02 . . . . . . . . . . . . . . . . . . . . . . .151, 383, 441
U2-03 . . . . . . . . . . . . . . . . . . . . . . 151, 380, 439 U4-03 . . . . . . . . . . . . . . . . . . . . . . .151, 383, 441
U2-03 through U2-17 . . . . . . . . . . . . . . 226, 227 U4-04 . . . . . . . . . . . . . . . . . . . . . . .151, 197, 383
U2-04 . . . . . . . . . . . . . . . . . . . . . . 151, 380, 440 U4-05 . . . . . . . . . . . . . . . . . . . . . . .202, 204, 216
U2-05 . . . . . . . . . . . . . . . . . . . . . . 151, 380, 440 U4-06 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 205
U2-06 . . . . . . . . . . . . . . . . . . . . . . 151, 381, 440 U4-07 . . . . . . . . . . . . . . . . . . . . . . .151, 383, 441
U2-07 . . . . . . . . . . . . . . . . . . . . . . 151, 381, 440 U4-09 . . . . . . . . . . . . . . . . . . . . . . .151, 384, 441
U2-08 . . . . . . . . . . . . . . . . . . . . . . 151, 381, 440 U4-10 . . . . . . . . . . . . . . . . . . . . . . .151, 384, 441
U2-09 . . . . . . . . . . . . . . . . . . . . . . 151, 381, 440 U4-11 . . . . . . . . . . . . . . . . . . . . . . .151, 384, 441
U2-10 . . . . . . . . . . . . . . . . . . . . . . 151, 381, 440 U4-13 . . . . . . . . . . . . . . . . . . . . . . . . . . . 151, 384
U2-11 . . . . . . . . . . . . . . . . . . . . . . 151, 381, 440 U4-14 . . . . . . . . . . . . . . . . . . . . . . .151, 384, 441
U2-12 . . . . . . . . . . . . . . . . . . . . . . 151, 381, 440 U4-16 . . . . . . . . . . . . . . . . . . . . . . .151, 384, 441
U2-13 . . . . . . . . . . . . . . . . . . . . . . 151, 381, 440 U4-18 . . . . . . . . . . . . . . . . . . . . . . .151, 384, 442
U2-14 . . . . . . . . . . . . . . . . . . . . . . 151, 381, 440 U4-19 . . . . . . . . . . . . . . . . . . . . . . .151, 384, 442
U2-15 . . . . . . . . . . . . . . . . . . . . . . 151, 381, 440 U4-20 . . . . . . . . . . . . . . . . . . . . . . .151, 384, 442
U2-16 . . . . . . . . . . . . . . . . . . . . . . 151, 381, 440 U4-21 . . . . . . . . . . . . . . . . . . . . . . .151, 385, 442
U2-17 . . . . . . . . . . . . . . . . . . . . . . 152, 381, 440 U4-22 . . . . . . . . . . . . . . . . . . . . . . .151, 385, 442
U3 Fault History . . . . . . . . . . . . . . . . . . . . . . . 381 U4-23 . . . . . . . . . . . . . . . . . . . . . . .151, 385, 442
U3-01 . . . . . . . . . . . . . . . . . . . . . . 152, 381, 440 U5 Application Monitor . . . . . . . . . . . . . . . . 386
U3-02 . . . . . . . . . . . . . . . . . . . . . . 152, 381, 440 U5-01 . . . . . . . . . . . . . . . . . . . . . . .151, 386, 442
U3-03 . . . . . . . . . . . . . . . . . . . . . . 152, 381, 440 U5-02 . . . . . . . . . . . . . . . . . . . . . . .151, 386, 442
U3-04 . . . . . . . . . . . . . . . . . . . . . . 152, 381, 440 U5-03 . . . . . . . . . . . . . . . . . . . . . . .151, 386, 442
U3-05 . . . . . . . . . . . . . . . . . . . . . . 152, 382, 440 U5-04 . . . . . . . . . . . . . . . . . . . . . . .151, 386, 442
U3-06 . . . . . . . . . . . . . . . . . . . . . . 152, 382, 440 U6 Application Monitor . . . . . . . . . . . . 386, 387
U3-07 . . . . . . . . . . . . . . . . . . . . . . 152, 382, 440 U6-01 . . . . . . . . . . . . . . . . . . 151, 386, 387, 442
U3-08 . . . . . . . . . . . . . . . . . . . . . . 152, 382, 440 U6-02 . . . . . . . . . . . . . . . . . . 151, 386, 387, 442
U3-09 . . . . . . . . . . . . . . . . . . . . . . 152, 382, 440 U6-03 . . . . . . . . . . . . . . . . . . . . . . . . . . . 151, 442
U3-10 . . . . . . . . . . . . . . . . . . . . . . 150, 382, 441 U6-04 . . . . . . . . . . . . . . . . . . . . . . .151, 386, 442
U3-11 . . . . . . . . . . . . . . . . . . . . . . 150, 382, 441 U6-05 . . . . . . . . . . . . . . . . . . . . . . .152, 386, 442
U3-12 . . . . . . . . . . . . . . . . . . . . . . 150, 382, 441 U6-06 . . . . . . . . . . . . . . . . . . . . . . .152, 386, 442
U3-13 . . . . . . . . . . . . . . . . . . . . . . 150, 382, 441 U6-07 . . . . . . . . . . . . . . . . . . . . . . .152, 386, 442
U3-14 . . . . . . . . . . . . . . . . . . . . . . 150, 382, 441 U6-08 . . . . . . . . . . . . . . . . . . . . . . .152, 386, 442
U3-15 . . . . . . . . . . . . . . . . . . . . . . 150, 382, 441 U6-17 . . . . . . . . . . . . . . . . . . . . . . . . . . . 152, 442
U3-16 . . . . . . . . . . . . . . . . . . . . . . 151, 382, 441 U6-18 . . . . . . . . . . . . . . . . . . . . . . . . . . . 152, 442
U3-17 . . . . . . . . . . . . . . . . . . . . . . 151, 382, 441 U6-19 . . . . . . . . . . . . . . . . . . . . . . . . . . . 152, 442
U3-18 . . . . . . . . . . . . . . . . . . . . . . 151, 383, 441 U6-20 . . . . . . . . . . . . . . . . . . . . . . .152, 386, 442
U3-19 . . . . . . . . . . . . . . . . . . . . . . 151, 383, 441 U6-21 . . . . . . . . . . . . . . . . . . . . . . .152, 387, 442
U3-20 . . . . . . . . . . . . . . . . . . . . . . 151, 383, 441 UL Standards . . . . . . . . . . . . . . . . . . . . . . . . . 425

464 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
UL3. . . . . . . . . . . . . . . . . . . . 183, 185, 203, 215 W
UL4. . . . . . . . . . . . . . . . . . . . 183, 185, 204, 215 Watchdog Circuit Exception . . . . . . . . . 183, 189
Undertorque 1. . . . . . . . . . . . . . . . . . . . .185, 215
watchdog circuit exception . . . . . . . . . . . . . . 190
Undertorque 2. . . . . . . . . . . . . . . . . . . . .185, 215
Watt Hour Output Unit Selection . . . . . 345, 441
Undertorque Detection 1 . . . . . . . . . . . . . . . . 183 Watt Hour Pulse Output. . . . . . . . . . . . . . . . . 347
Undertorque Detection 2 . . . . . . . . . . . .183, 204
Watts Loss 200 V Class Single Phase Models 302
Undervoltage . . . . . . . . . . . . . . . . 183, 185, 215
Watts Loss 200 V Class Three Phase Models 303
Undervoltage 3 . . . . . . . . . . . . . . . . . . . . . . . . 205 Watts Loss 400 V Class Three Phase Models 304
Undervoltage Detection 1. . . . . . . . . . . . . . . . 203
Wire Gauge, Single Phase 200 V Class. . . . . . 64
Undervoltage Detection Level (UV) . . .354, 433
Wire Gauge, Three Phase 200 V Class . . . . . . 64
Unexpected Noise from Connected Machinery237 Wire Gauge, Three Phase 400 V Class . . . . . . 65
Unit Selection for Memobus/Modbus Register
Wire Gauges . . . . . . . . . . . . . . . . . . . . . . . . . . 63
0025H . . . . . . . . . . . . . . . . . . . . . . . . . . .351, 442
Wiring Checklist . . . . . . . . . . . . . . . . . . . . . . . 84
Unstable Motor Speed when Using PM . . . . . 239 Wiring Procedure. . . . . . . . . . . . . . . . . . . . . . . 74
Up 2 Command. . . . . . . . . . . . . . . . . . . . . . . . 344
Up Command . . . . . . . . . . . . . . . . . . . . . . . . . 342 Z
User Monitor Selection After Power Up 370, 436 Zero Speed. . . . . . . . . . . . . . . . . . . . . . . . . . . 345
User Parameter Automatic Selection . . 113, 312,
433
User Parameter Default Value113, 164, 371, 436
User Parameters, 1 to 32. . . . . . . . . . . . .312, 433
Uv . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .185, 215
Uv1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .183, 204
Uv2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .183, 205
Uv3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .183, 205

V
V/f Control . . . . . . . . . . . . . . . . . . 122, 139, 156
V/f Control Mode Tuning. . . . . . . . . . . . . . . . 177
V/f Control Mode Tuning Parameters . . . . . . 177
V/f Data Setting Error . . . . . . . . . . . . . .185, 220
V/f Pattern . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
V/f Pattern Selection. . . . . . . . . . . 233, 330, 438
V/F patterns When in V/F Control Mode. . . . 389
VC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
Vector motor . . . . . . . . . . . . . . . . . . . . . . . . . . 149
Verify Menu . . . . . . . . . . . . . . . . . . . . . . . . . . 102
VMAX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
VMIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140

YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual 465
466 YASKAWA ELECTRIC TOEP C710606 22A YASKAWA AC Drive - V1000 Installation & Start-Up Manual
Revision History

The revision dates and numbers of the revised manuals are given on the bottom of
the back cover.
MANUAL NO.‫ޓ‬TOEP C710606 22A
Printed in Japan April 2007 07-4

Date of
printing Date of original
publication

Date of Priting Rev. No. Section Revised Content

April 2007 − − First edition
YASKAWA AC Drive-V1000
Compact Vector Control Drive
Installation & Start-Up Manual

YASKAWA ELECTRIC AMERICA, INC.

Drives Division
16555 W. Ryerson Rd., New Berlin, WI 53151, U.S.A.
Phone: (800) YASKAWA (800-927-5292) Fax: (262) 782-3418
Internet: http://www.drives.com

YASKAWA ELECTRIC AMERICA, INC.

Chicago-Corporate Headquarters
2121 Norman Drive South, Waukegan, IL 60085, U.S.A.
Phone: (800) YASKAWA (800-927-5292) Fax: (847) 887-7310
Internet: http://www.yaskawa.com

YASKAWA ELECTRIC CORPORATION

New Pier Takeshiba South Tower, 1-16-1, Kaigan, Minatoku, Tokyo, 105-0022, Japan
Phone: 81-3-5402-4511 Fax: 81-3-5402-4580
Internet: http://www.yaskawa.co.jp

YASKAWA ELECTRIC EUROPE GmbH

Am Kronberger Hang 2, 65824 Schwalbach, Germany
Phone: 49-6196-569-300 Fax: 49-6196-888-301

YASKAWA ELECTRIC CORPORATION

YASKAWA

In the event that the end user of this product is to be the military and said product is to be employed in any weapons systems or the manufacture
thereof, the export will fall under the relevant regulations as stipulated in the Foreign Exchange and Foreign Trade Regulations. Therefore, be
sure to follow all procedures and submit all relevant documentation according to any and all rules, regulations and laws that may apply.
Specifications are subject to change without notice for ongoing product modifications and improvements.
© 2007 YASKAWA ELECTRIC CORPORATION. All rights reserved.

MANUAL NO. TOEP C710606 22A

Printed in Japan April 2007 07-4
07-4