Complete machine solution

User Manual

Handheld Laser Marking Machine/LM/LMB series

Changchun Bluetimes International trading Co.,ltd.

 Changchun Bluetimes International trading Co.,ltd.

Security Information

A.Safety Sign

Severe personal injury or even life-threatening may result.

May cause general personal injury or damage to the product

or equipment.

B.Laser safety class

According to the European standard EN 60825-1, clause 9, the laser
inside this device is a class 4 laser. This product emits laser radiation with
wavelengths around 1064nm and can cause damage to eyes and skin when
directly or indirectly exposed to such light levels. Although this radiation is
invisible, the beam can still cause irreversible damage to the retina or
cornea. Appropriate and certified laser safety goggles must be worn when
the laser is operating.

Be sure to wear laser safety goggles throughout the oper-

ation of this product. Laser safety goggles have laser wave-
length protection selectivity, so users are requested to choose
laser safety goggles that conform to the laser output band of
the product. When the hand-held laser marking machine is
powered on, it is forbidden to point the laser output head to
the direction of people, and prohibit the laser output head to
irradiate the mirror surface of strong reflective material.
 Changchun Bluetimes International trading Co.,ltd.

C.Safety Sign

Figure 1.1 Laser marking Figure 1.2 Fiber Do Not Break Mark

D.Electrical Safety

①Please ground the product through the PE wire in the power cord,
and ensure that the grounding is firm and reliable.

A disconnection of the ground will cause the product case to

become live, which may result in personal injury to the operator.

②Make sure that the AC voltage supply is normal.

Incorrect wiring or power supply voltage will cause irrevers-

ible damage to the laser.
 Changchun Bluetimes International trading Co.,ltd.

Preamble
1. Welcome
Thank you for choosing our company's portable handheld laser
marking machine product. This user manual provides you with
important safety, operation, maintenance and other precau-
tions. Therefore, before using this product, please read this
user manual carefully and keep it properly. To ensure safe oper-
ation and optimum product condition, please observe the fol-
lowing cautions and warnings.
This user manual is not a quality guarantee. Corrections of
printing errors, modifications to the information described,
and product improvements are all explained by our company at
any time without prior notice, and the corrections will be incor-
porated into the reprinted user manual.
2.Product Introduction
Laser marking is a new technology based on the interaction of laser and material,
which can achieve the effect of clear marking on the surface of objects. Compared
with traditional marking methods, hand-held laser marking has the advantages of
precise marking, no damage to the substrate, "green" environmental protection,
and online availability, and is especially suitable for high-speed online marking in
designated areas.

Figure 2.1 Sketch map of laser marking

The handheld laser marking equipment produced by our company is a new gener-
ation of high-tech laser marking products, which are easy to install, operate and
automate. Simple operation, turn on the power supply and turn on the equip-
ment, you can carry out efficient, accurate, and consumable-free "green" marking.
It can mark metal and various non-metallic materials, and is widely used in the in-
dustry, covering hardware products, tool accessories , precision equipment, auto
parts, plastic buttons, building materials, medical equipment and other industries.

2.1Equipment Characteristics and Implementation Standards

 Changchun Bluetimes International trading Co.,ltd.

（1）Equipment features
△ Efficient and accurate marking without damaging the part matrix;
△ Precise marking, which can realize selective marking of precise position and
precise size;
△ No need for any consumables, safe and environmentally friendly;
△ Easy to operate, portable and handheld marking;
△ Ergonomic design, the labor intensity of operation is greatly reduced;
△ High marking efficiency and saving time;
△ The laser marking system is stable and requires almost no maintenance;
△ Optional mobile battery module;

（2）Product implementation standards

Our company has passed the ISO 9001 international quality management system
certification, and has formed a quality assurance system for the design, produc-
tion and service of small and medium power laser processing equipment.
Our company has formulated detailed standards for the working environment
and working conditions, basic technical requirements, cooling requirements,
laser radiation safety, electrical safety, test methods, inspection and acceptance,
packaging and transportation in the production process. The standards are:
GB10320 Electrical Safety of Laser Equipment and Facilities
GB7247 Radiation Safety, Equipment Classification, Requirements and User
Guide for Laser Products
GB2421 Basic environmental test procedures for electronic products
GB/TB360 Specification for Laser Power Energy Test Instrument
GB/T13740 Test method for divergence angle of laser radiation
GB/T13741 Test method for beam diameter of laser radiation
GB/T13862-92 Test method for laser radiation power
GB2828-2829-87 Batch-by-batch periodic inspection and counting sampling pro-
cedure and sampling table
 Changchun Bluetimes International trading Co.,ltd.

2.2 Operating Environment and Related Parameters

 Changchun Bluetimes International trading Co.,ltd.

2.3Product structure and dimension drawing

（1）Dimensions of the marking handle

Dimensions of marking handle

（2）Dimensions of the machine

Dimensions of Handheld Laser Marking Machine

 Changchun Bluetimes International trading Co.,ltd.

2.4 Configuration List

Handheld laser marking machine equipment configuration list

 Changchun Bluetimes International trading Co.,ltd.

3.Installation and use of handheld laser marking machine

Precautions before use:
Check whether the appearance of the device is abnormal, and whether the
output cable is bent or damaged;
Please make sure the power socket is in good contact;
Check and ensure that there is no dust inside and outside the field lens at the
hand-held marking handle;
Check and ensure that the buttons and switches on the whole machine are in
normal state;

3.1 Operating Steps

[Step 1]Take the handheld marking handle and remove the lens dust cover of
the field lens of the laser marking handle;
[Step 2] Insert one end of the special power adapter into the power port of the
handheld laser marking machine, connect the power cord plug at the other end,
and press the power button;
[Step 3] After the system is started, complete the parameter setting of the laser
marking file through the touch screen interface;
[Step 4] After setting the parameters of the laser marking file, put on the laser
protective glasses, align the handle with the workpiece to be processed, press
the laser marking key on the handle with your finger to display the red light pre-
 Changchun Bluetimes International trading Co.,ltd.

view of the processing file, and press the laser marking key on the handle again
After marking, you can also use the touch screen interface of the control soft-
ware to click to power on, preview with red light, and output marking;
[Step 5] After use, turn off the power button of the laser marking screen, cover
the dust cover of the field lens, turn off the power button, and cut off the power
supply of the special power adapter.

3.2 Software control interface

After the system enters the main interface, the middle part is the canvas to dis-
play the drawn graphics, the left side is the commonly used objects, and the
right side is the operation of these objects. The upper part is the real-time dis-
play of the position and size of the object, and the lower part is the marking and
red light preview buttons.
[File] System file operations, including creating a new file, opening a file, saving
a file, and saving as a file.
[System Settings] Configure system parameters, including laser type, calibra-
tion, marking format settings, etc.
 Changchun Bluetimes International trading Co.,ltd.

[Properties] Configure marking parameters, including marking speed, laser

power, etc.

[Zoom in] Zoom in on the view area. [Zoom out] Zoom out the view area.

[View] Zoom the drawing area so that the selected object fills the visible area.

[Recovery] Zoom the drawing area to fill the visible area with the marking area.

[Text] Add text.

[QR Code] Add a QR code object.

[Bitmap] Add pictures, including (png, jpg, bmp formats).

[Vector] Add vector files (dxf, plt, svg).

[Geometry] Add rectangles, circles, lines.

[ Fill ] Fill the current object with scan lines.

[Group] Combine the selected objects into a Group object and operate as a

whole.

[Dissolve] dissolve the object.

[Object List] Displays the objects drawn in total.

[Undo] Undo the previous operation.

[Redo] Redo the action just now.

[Edit] Modify the parameters of the drawn object.

[Mirror] Flip the current object (horizontal, vertical).

[Array] Arranges the current objects according to a certain distance.

[Delete] Delete the current object.

[Copy] Copy the current object and paste it.

[Move Up] Move the object up. [Move Down] Move the object down.

[Move Left] Move the object to the left. [Move Right]Move the object to the right.
[Center] Center the object to display.

[Red light] Preview the drawn object with red light without laser light.
[Mark] Laser mark the drawn object.
 Changchun Bluetimes International trading Co.,ltd.

1.1 Text editing

Including position setting, content setting, variable text, arc text setting.

1.1.1 Location Settings

[X] The x-coordinate of the object's center point.

[Y] The y coordinate of the object's center point.
[W] The width of the object. [H] The height of the object.
[Angle] The rotation angle of the object.

1.1.2 Content Settings

 Changchun Bluetimes International trading Co.,ltd.

[Text] Modify the text content.

[Font type] TrueType font, monoline font.
[Font name] such as Hei, Song, etc.
[Character Spacing] The distance between characters.
[Line Spacing ] The distance between two lines of text.
[Alignment] When the text has multiple lines, you can choose the align-
ment, left, center, and right.
[Style] bold, italic.
[Arrangement direction] horizontal or vertical.

1.1.3 Variable Text

Such as fixed text, serial number, date, time, external file, VINCODE, etc.

1.1.3.1 Fixed text

Display fixed content, such as inputting TEXT, the software interface has
built-in: - / Three formats, click these three to quickly set the content. Or
check the line break and add a line.
 Changchun Bluetimes International trading Co.,ltd.

1.1.3.2 Serial number

[Starting Serial Number] The starting value of the serial number.

[Current Serial Number] The displayed value of the current serial number.
[Maximum serial number] When the processed serial number is equal to the
serial number value, the system automatically returns to the starting serial
number.
[Jump Number Increment] The increment value of the serial number each
time.
[Repeated marking times] The current serial number is marked several
times, and after repeated marking several times, it will be increased accord-
ing to the jump number increment.

1.1.3.3 Date
The date element is a text element that the system automatically fetches
date information from the computer during processing. When the user se-
lects the date element, the date element is automatically displayed in the
text element dialog box, as shown in the following figure:
 Changchun Bluetimes International trading Co.,ltd.

[Year-2022] Use the year of the current computer clock as the correspond-
ing text, formatted as 4 characters.
[Year-22] Use the year of the current computer clock as the corresponding
text, the format is 2 characters, and only the last two digits of the year are
taken.
[Month-07] Use the month of the current computer clock as the correspond-
ing text, in the format of 2 characters.
[Day-19] Use the day of the month of the current computer clock as the cor-
responding text, formatted as 2 characters.
[Day-200] Use the current computer clock's current day in days from Janu-
ary 1 as the corresponding text in 3-character format. (January 1 is 001,
January 2 is 002, and so on).
[Week-02] Use the day of the week of the current computer clock as the cor-
responding text, the format is 2 characters.
[Week-30] The current day using the current computer clock is the week of
the year as the corresponding text, in 2-character format. (The first week is
from January 1st to the first Saturday).
 Changchun Bluetimes International trading Co.,ltd.

[Date offset] When the system takes the date of the computer clock, the
offset date must be added to be the date to be processed. This function is
mainly used for the processing of workpieces with production date and
quality guarantee date in food and other industries. Custom month charac-
ters: When the user selects the month as the corresponding text, the follow-
ing image will appear on the right. The user can define the character of the
month by himself, instead of using the default number of the software, use
other characters to represent it, just double-click the selected month, input
other characters representing the month, and finally the month displayed
on the software interface is the input character. indicated.

When the user selects a four-character year, it will appear on

the right side. After checking it, the user can define the year character by
himself, and the operation is the same as when customizing the month
character.

1.1.3.4 Time
During the processing, the system automatically fetches the elements of
time information from the computer, and the output content is the current
computer time. Each time it is output, the text content is updated to the
current time.
 Changchun Bluetimes International trading Co.,ltd.

1.1.3.5 External File

Read content from files, support TxT files, xlsx files.
 Changchun Bluetimes International trading Co.,ltd.

1.1.3.6 VINCODE

1.1.4 ARC

[Starting Angle] starting angle of the first character.

[Included Angle] the angle range of the arc circle (for example, 360 degrees
means arc text is circular arc text, and 180 degrees means arc text is
semi-circular arc text).
 Changchun Bluetimes International trading Co.,ltd.

[Arc Radius] the size of the arc.

[Clockwise] characters are arranged clockwise.
[Flip] characters inward or outward.

2.1 QR code editing

Including position settings, content settings, variable text.

2.1.1 Position Settings

[X] the X-coordinate of the object's center point.

[Y] the Y-coordinate of the object's center point.
[W] the width of the QR code.
[H] the height of the QR code.
[Angle] the rotation angle of the QR code.
[Border Width] the width of the distance edge when the QR code is re-
versed.
 Changchun Bluetimes International trading Co.,ltd.

2.1.2 Content Settings

[Content] the content to be displayed in the QR code.

[Barcode Mode] QR code, Bar code.
[Barcode Type] BarCode：CODE25、CODE39、CODE93、CODE128。
QRCode: QRCode、DataMatrix。

[Variable Text] such as serial number, date, time, etc.

[Display Mode] positive or reverse.
[Positive]

[Reverse] added a border around the QR code.

[QRCode Style] standard mode, dot mode, circle mode, rectangle mode.
[Dot Mode] [Circle Mode] [Rectangle Mode]
 Changchun Bluetimes International trading Co.,ltd.

2.1.3 Variable Text

Please refer to the variable text of the text，1.1.3。

2.2 Bitmap editing

Including position settings and image settings.

2.2.1 Position Settings

[X] the X-coordinate of object's center point.

[Y] the Y-coordinate of object's center point.
[W] the width of the object.
[H] the height of the object.
[Angle] the rotation angle of the object.

2.2.2 Image Settings

 Changchun Bluetimes International trading Co.,ltd.

2.1.3 Variable Text

[Positive or Reverse] reverse the color value of each point in the current
image.

[Positive]
 Changchun Bluetimes International trading Co.,ltd.

[Reverse]

[Brightness] adjust the brightness of the picture, the larger the value, the
brighter the picture, the smaller the value, the darker the picture.

[Contrast ratio]make the bright parts of the picture brighter and the dark
parts darker.

[Point Time] refers to whether the laser is always on when processing each
pixel of the bitmap, or each pixel is on for a specified time.

[Fixed DPI] similar to the resolution of the picture. Since the DPI value of the
original bitmap file is not fixed or uncertain, you can set a fixed DPI value
through "Fixed DPI", which can be set separately in the X and Y directions.
The larger the DPI value, the denser the dots, the higher the image accura-
cy, and the longer the processing time.

[Marking Resolution] displays the resolution of the image, which will vary
according to the size of the image.
 Changchun Bluetimes International trading Co.,ltd.

2.3 Fill
Which can fill the specified graphics. The shape to be filled must be a closed
curve.

[Enable Profile] indicates whether to display and mark the outline of the origi-
nal graphics. That is, whether the filled graphic retains the original outline.
indicates that in the case of“Enable profile”, fill lines are marked first
and then outlines are marked.
indicates that in the case of "enable outline", the outline is marked
first and then the fill line is marked.

Fill 1、Fill 2 and Fill 3：it means that three sets of unrelated filling parameters
can be set at the same time for filling. Cross-filling at any angle can be done,
and each filling can support four different filling types.(The four filling types in-
 Changchun Bluetimes International trading Co.,ltd.

clude Unidirectional Filling, Bidirectional Filling, Ring Filling, and Optimized

Bidirectional Filling, see below for details).
[Unidirectional Fill] fill lines always fill from left to right.
[Bidirectional Fill] the fill line is filled from left to right first, then from
right to left, and the rest is filled in a loop.
[Bow Fill] optimized bidirectional fill: Similar to bidirectional fill, but
creates connecting lines between the ends of the fill lines.
[Optimized Bow Fill] similar to bow fill.
[Ring Fill] the fill line is the outline of the object to be filled cyclically
from the outside to the inside.
[Angle] refers to the angle between the fill line and the X axis.
[Line Spacing] refers to the distance between adjacent fill lines.
[Fill Line Margins] refers to the distance between the filling line and the out-
line object in all filling calculations.
[Walk Around Once] refers to adding a contour figure around the periphery of
the filling line after the filling calculation is completed.
[Evenly Distributed Fill Line] resolved an issue with uneven distribution of fill
lines at the start and end of fill objects. Due to the size of the filling object
and the setting of the spacing between the filling lines, after filling, uneven
distribution of the filling lines may occur at the beginning and end of the fill-
ing object. In order to simplify the operation, the purpose of uniform distri-
bution of all filling lines can be achieved without the need for the user to
reset the line spacing, and this function is added. After selecting this item,
the software will automatically fine-tune the filling line spacing based on
the filling line spacing set by the user, so that the filling lines are evenly dis-
tributed.
[Start Offset] refers to the distance between the first fill line and the boundary.
[End Offset] refers to the distance between the last fill line and the border.
 Changchun Bluetimes International trading Co.,ltd.

[Line Indent] refers to the indentation at both ends of the filling line. If it is
positive, it is the indentation. If it is negative, it is the extension.
[Number of Rings] Refers to the number of ring fills before horizontal fills.
Since the last ring may not be filled evenly when using "Ring Fill" complete-
ly, this function is used to solve such problems.

2.4 Mirror
Horizontal and vertical mirroring。

Original image:

Horizontal mirror:

Vertical mirror:

2.5 Arrays
Arrays include rectangular arrays and circular arrays.
 Changchun Bluetimes International trading Co.,ltd.

[Rectangle]
 Changchun Bluetimes International trading Co.,ltd.

[Circular]
 Changchun Bluetimes International trading Co.,ltd.

2.6 Align

[Align Right] Align the selected objects to the right.

[Align Left] Align the selected objects to the left.
[Horizontal Alignment] align the selected objects to the vertical center line.
[Vertical Alignment] align the selected objects to the horizontal center line.
[Align Top] align the selected objects horizontally with their top edge.
[Align Bottom] align the selected objects horizontally with their bottom
edge.
[Equal High] set selected objects to the same height.
[Equal Width] set selected objects to the same width.
[Vertically Centered] align selected objects with horizontal center line.
[Horizontally Centered] aligns the selected objects to their vertical center
lines.

2.7 File

[New File] create a new workspace for drawing. When you select "New File",
the software will close the file you are currently editing and create a new file
at the same time. If the file you are currently editing has not been saved, the
software will prompt you whether to save the file.
 Changchun Bluetimes International trading Co.,ltd.

[Open File] to open a saved file, "Open File" is used to open a file which
saved on the hard disk. When you select "Open File", an open file dialog box
will appear, asking you to select the file you want to open.
[Save] overwrite the original file, "Save" saves the drawing being drawn
with the current file name.
[Save As] set the file name, "Save As" is used to save the currently drawn
graphics as another file name, both of which realize the function of saving
the file. When you click "Save As", the following dialog box will appear:
select the location to save.

2.8 Attributes

On the left side are 8 groups of layer buttons, which means that the system
can store 8 groups of different marking parameters, and each group of pa-
rameters can be set individually.
[Use Default Parameters] if the default parameters are checked, the default
parameters will be used. If the default parameters are not checked, the pa-
rameters of the current layer can be customized and saved.
 Changchun Bluetimes International trading Co.,ltd.

[Layer Number] the layer where the object is located.

[Marking Times] after clicking mark, the number of times of laser marking.
[Marking Speed] the operating speed of the galvanometer when the laser is
out of light.
[Idle Speed] the moving speed of the galvanometer when the laser does not
emit light.
[Open Delay] Delay time to turn on the laser when marking starts. Setting
the appropriate "Turn-on Delay" parameter can remove the "match head"
phenomenon at the beginning of marking, but if the light-on delay parame-
ter is set too large, it will lead to the missing phenomenon of the initial seg-
ment, which can be negative.

Parameter is too large Parameter is too small Parameters are normal

[Close Delay] Delay time to turn off the laser when marking is end. Setting
the appropriate close delay parameter can eliminate the non-closing phe-
nomenon when marking is completed. But if the close delay is set too large,
it will cause a "match head" phenomenon in the end segment, which cannot
be a negative value.

Parameter is too small Parameter is too large Parameters are normal

 Changchun Bluetimes International trading Co.,ltd.

[Corner Delay] one stroke sends an end command, the next one sends a
start command, and there is no empty stroke in the middle. At this time, due
to the lag of the galvanometer, it will take a period of time for the galva-
nometer to reach the designated position. If the parameter is too large, the
galvanometer has been fully rotated, and the laser does not stop emitting
light at this time, and then there will be repeated points in the corners; If the
parameter is too small, the galvanometer has not been fully rotated, and
the next segment will be marked, and an arc will appear at the corner.

Parameter is too small Parameter is too large Parameters are normal

[Jump Delay] the time to wait for the galvanometer to reach the specified
position. When the last command of the empty stroke is given, due to the
lag of the galvanometer, it will take a period of time to reach the specified
position, so this parameter should be set to wait for the galvanometer to
reach the specified position. If the parameter is too large, the galvanometer
has been fully rotated, and the next stroke is processed after staying for a
period of time, which increases the marking time; If the parameter setting is
too small, the galvanometer has not been fully turned to the laser and the
light has been emitted, and scattered points will appear at the beginning of
the stroke.

Jump delay is normal Parameter is too small

 Changchun Bluetimes International trading Co.,ltd.

[Over Delay] time to wait for the laser to turn off completely. The laser
needs a period of response time from the time the light-off command is
issued until the laser is completely turned off. Setting an appropriate over
delay parameter is to give the laser sufficient light-off response time, so as
to achieve the purpose of turning off the laser completely and then marking
the next time. Appropriate over delay parameters can eliminate the "smear-
ing" phenomenon that occurs when marking. But if the end delay is too
large, it will affect the processing speed. Cannot be a negative value.
[Laser Power] the output power of the laser in the state of light output.
[Pulse Width] refers to the time that the laser power is maintained at a cer-
tain value.
[Frequency] refers to the number of times the laser emits light per unit time.

2.9 System Settings

Including galvo settings, laser settings, red set, calibration settings, startup
settings, system, other.

2.9.1 Galvo Settings

 Changchun Bluetimes International trading Co.,ltd.

[Work Size] the effective range of galvanometer marking, the default is

50mm, the range is 50mm ~ 150mm.
[Coordinate Axis Settings]
①XY Change：after selected, swap XY axis when outputting。
②X-axis negative：after selected, the X-axis will be negative when output-
ting.
③Y-axis negative: after selected, the Y-axis will be negative when output-
ting.
[Mission End Coordinates] the position where the red light stays,after the
marking task is over, there are three options.
①Default location：the red light stays at the position where the marking
task ends.
②Designated location：you can directly input the value of X and Y to deter-
mine the position where the red light will stay after marking, the range is
-450mm ～ 450mm.
③Galvo Center：after marking, the red light stays at the center of the galva-
nometer。
[Center Offset]
[Offset X] adjust the horizontal center (laser output) position of the galvo
mirror.
[Offset Y] adjust the vertical center (laser output) position of the galvo
mirror.
[Shoot Y] Adjust the vertical center (laser output) position of the vibration
mirror.
 Changchun Bluetimes International trading Co.,ltd.

2.9.2 Laser Settings

Laser type choosing should be the same as the actual laser type. This soft-
ware provides four types of laser, including CO2, YAG, FIBER, SPI.
[CO2] The current laser type is CO2 laser.
[YAG] The current laser type is YAG laser.
[Fiber] The current type of laser is a fiber laser.
[SPI] The current laser is SPI fiber laser.
[Light leakage treatment] After selecting this item, the laser will be opti-
mized for light leakage.

2.9.3 Red Light Setting

 Changchun Bluetimes International trading Co.,ltd.

[Red light settings]

[Horizontal offset] Adjust X center position when red light preview.
[Vertical offset] Adjust Y center position when red light preview.
[Horizontal ratio] The proportion of horizontal dimensions and theoretical
dimensions of red light output.
[Vertical ratio] The proportion of vertical dimensions to theoretical dimen-
sions of red light output.
[Red light speed] red light scanning speed.

2.9.4 Correction Settings

 Changchun Bluetimes International trading Co.,ltd.

Click the label button to label a rectangle, the size is set. Observe whether
the rectangle of the knocked is deformation. (Deformation generally has
three types of barrel pillow, trapezoidal, Parallelogram), and deformation is
X -axis and Y axis deformation, respectively. By adjusting the parameters of
the X -axis and Y axis directions, the deformation can be corrected. The set-
ting of the parameter can be positive or negative, and the positive and neg-
ative of the value represents the correction trend. The absolute value of the
value represents the strength of the correction. Increasing the setting data
absolute value can enhance the intensity of correction. If you find that the
adjustment is too much, you can reduce it appropriately.
 Changchun Bluetimes International trading Co.,ltd.

As shown in the figure above, there are barrel pillow -shaped distortion.
Among them, A and B are Y -axis deformation, A is too small in the deforma-
tion coefficient, and B is too large in the deformation coefficient; C and D are
X -axis deformation, C is too large deformation coefficient, D is too small in
the deformation coefficient. The correction parameter setting range of the
barrel pillow is -0.5-+0.5.

As shown in the figure above, it is a parallel secondary deformation. Among

them, A is a deformation of X, and B is a deformation of Y direction.

As shown in the figure above, A and B are trapezoidal deformation in the X

-axis. Among them, A is too small in trapezoidal deformation coefficient,
and B is too large in trapezoidal deformation coefficient; D is the trapezoidal
deformation coefficient, and the setting range is -1 to +1.
After the correction is completed, the size correction is performed, and the
actual size of the X -axis and Y axis direction of the bench marking graphics
manually, and then click the >> button after the x ratio and Y ratio. Value,
(can also be cleared up and redesigned) Correct work is completed, click the
application and exit.
 Changchun Bluetimes International trading Co.,ltd.

2.9.5 Startup Settings

[Enable starting up] Choose Startup. When the system starts, it will auto-
matically open the preserved file in the boot list. If there is only one file in
the boot list, then it will be opened by default. If there are many, you need
to choose one of them to open it. , Or click to cancel, do not open all.

[Add] Add startup file to the list.

[Delete] Delete the startup file from the list.
[Remove] remove the startup list.
 Changchun Bluetimes International trading Co.,ltd.

2.9.6 system

[System upgrade] Click the system upgrade, select the upgrade file (must
be .bin file). After the upgrade, you need to restart.
[Language] Support Chinese and English.
[Subject] Support multiple sets, dark, light, blue, green, orange.
 Changchun Bluetimes International trading Co.,ltd.

2.9.7 Other

[Horizontal paste offset] When copying the paste, the new object position
is shifted to the horizontal direction of the original object.
[Vertical paste offset] When copying the paste, the new object position is
shifted to the vertical direction of the original object.
[Grid size] When the main interface displays the table, the size of each grid.

3.Special Function

3.1 Choose the object and press for a second

Selecting the object and press for a second, pop up the menu dialog box.
There are some common operations can directly operate the object. Users
no longer need to care about which positions these buttons are in the main
interface to facilitate the user's operation.
 Changchun Bluetimes International trading Co.,ltd.

When choose a straight line, there is an extra line and vertical line, which is
convenient for users to quickly set the straight line to horizontal or vertical.
 Changchun Bluetimes International trading Co.,ltd.

3.2 Press the blank position for a second

[Hide left side] Hide the left area.

 Changchun Bluetimes International trading Co.,ltd.

[Hide the right side] Hide the right area.

Left and right are hidden at the same time.

 Changchun Bluetimes International trading Co.,ltd.

3.3 Double -click the object of the selection to pop up the

editing interface
For example: Double -click the text object and directly pop up the editing
interface of the text object.

3.4 Precautions
If you don’t use this handheld laser marker according to this use manual,
it may reduce reliability and life of the product. So please read the follow-
ing requirements and precautions carefully, and follow the relevant specifi-
cations during use.
a) This handheld laser marker use 220V /50Hz AC power;
b) A ventilated distance of about 10cm around the equipment must be left.
Insufficient ventilation distance may cause internal laser failure and unable
to work!
c) Normal use temperature range is 0 ~ 40 ° C, internal laser system to
report to the alarm without light if exceeds the temperature range.
 Changchun Bluetimes International trading Co.,ltd.

d) Please keep laser head clean. Use a protective cover to cover the laser
output port under the non -working state. The dust on end of the head
output may cause the lens too heat and damage, causing the equipment
output power attenuation or cannot output light.
e) Before cleaning maintenance equipment and handheld marking handles
should ensure that the device is in power -off state.
f) During the operation,please wear labor protection supplies in accor-
dance with regulations, and protective glasses near the laser beam.
g) When the handheld laser marking machine is powered on, please do not
watch the laser output head directly. The laser output head is prohibited
from facing the position of someone, and the laser output head is prohibit-
ed from irradiation of the high -retained mirror.
h) Do not place flammable and explosive items near the handheld laser
marking machine! Such items should avoid direct or reflected laser!
i) Forbidden excessive bending tip of the ripple, the ripple tube bending
radius is ≥150mm to prevent the optical fiber in the ripple tube.
j) This handheld laser marking machine standby time is 60s. Software inter-
face, laser, and vibration mirror motor stopped working when no operation
reached 60s . Press the handle button to activate. The s standby time can
change according to demand.
K) When the lithium battery power is less than 20%, the software will
prompt the countdown to enter the low -power state for 5 seconds. Please
connect the appointment to charge. After that, the software enters the dor-
mant state and connects the special power adapter to activate the soft-
ware after power on.
 Changchun Bluetimes International trading Co.,ltd.

3.6 Common faults and treatment

Fault 1: Machine not startup when power on
1. Check whether the line is short circuit
2. Check whether the line is loose
3. Check whether the power supply (battery) has power-up

Fault 2: Laser source does not output laser

1. Check whether the laser source through power
2. Check whether the focal length is correct
3. Check whether there is a foreign body obstruction black light hole
4. Check whether the system control line falls off and loose
5. Check whether the software attribute settings are normal (laser power,
laser frequency).

Failure 3: Vibration mirror does not swing

1. Check whether the mirror motor is shaking
2. Check whether the two the mirror motor are tight

Failure 4: Screen problem

1. The screen does not light up,check whether 15V power-up successful.
2. Check whether the screen is cracking

Fault 5: Font printing incomplete or deformation

1.Adjust the software attribute options in the open light delay, close light
delay, corner delay.
2.Check the software system settings option to set the correction of the pa-
rameter to set the parameters normally.
 Changchun Bluetimes International trading Co.,ltd.

3.7 Maintenance
After the equipment using finished, the dust or foreign objects must blow
off with a blown -ear ball, use alcohol or rubbing the mirror paper (wipe
without dust)
The equipment heat sink needs clean every 2 to 3 months, please do it
under station of machine power off (can be cleaned up with clean and
moisture -containing compressed air)

4 .Pre -sale and after -sales service

4.1 service commitment
Our company focus on customer, fully know well customer’s marking
require, and provides comprehensive and personalized debugging, training,
maintenance, etc. before -sales and after -sales service to customers .
(1) Pre -sale service
Before signing the contract, my company provides various production process
plans, technical consulting, sample samples, and equipment selection services
of laser marking equipment.
(2) Machine debugging
Based on the contract, our company will transport the equipment safely to the
location designated by the user within the prescribed time, contact our cus-
tomer service staff, and online equipment technology guidance services.
(3) After -sales training
My company provides free online technology training, until the operator
reaches the basic use of the device, the main training content is as follows:
Laser marking technology basic principles;
Laser marking equipment main structure;
Laser marking equipment operation;
Laser marking process parameter adjustment;
Laser marking equipment maintenance ;
 Changchun Bluetimes International trading Co.,ltd.

(4) After -sales commitment

Free warranty for equipment for one year (excluding human damage, fiber
break);
Free technical consulting, process and software upgrade services;
Provide maintenance services for life, only for accessories of accessories;
Provide extensive software and hardware support for life

4.2 Limitation of warranty

Products and share parts (including fiber) caused by tampering, opening,
disassembly, misunderstanding and improvement caused by non -our
company's personnel are damaged; or damage caused by misuse, negli-
gence, or accidents; Or beyond the use of specifications, abuse or mainte-
nance, abuse or no damage caused by information and warnings on the
user manual, and the damage caused by the use of the warning is not
within the warranty range. Customers have the responsibility to under-
stand and operate in accordance with the user manual and operation
scope, and the damage caused by the wrong operation is not warranty.
Parts and other parts such as attachments are not within the warranty
range.
Within the warranty, if the buyer finds any problem, it must be written in
writing within 30 days from the date of discovery. This warranty does not
involve third parties (including specified buyers, end users or customers). It
does not include parts, equipment or other products produced by non
-company.

4.3 Technical support and product repair

This product does not need users to repair parts, components and compo-
nents, and all maintenance operations should be carried out by our compa-
ny's technicians.
 Changchun Bluetimes International trading Co.,ltd.

If any failure in the process of use, please notify our company's technical
personnel in time and deal with them.
All maintenance and replacement products must be placed in the original
packaging box provided by our company, otherwise our company has right
to refuse repairing if product damage caused by that.
When you receive products, please check whether the product is complete
and non -destructive in time and whether the accessories are complete. If
there are any abnormalities, please contact the carrier in time and contact
our company.
Our company will continue to develop new products. The product informa-
tion listed in the manual may change without notice. All technical parame-
ters are subject to contract terms.
The above -mentioned our company's warranty and service terms are for
users' reference only. The formal service and warranty content shall prevail
in the contract.