Scribd
Upload
51 views5 pages

Switch From Voss To Exo S

This document outlines the procedure for switching a VOSS switch to the EXOS Network Operating System, primarily using ExtremeCloud IQ or VOSS CLI commands. It details the necessary steps, including transferring the NOS image, confirming the change, and restarting the switch, while noting that all previous configurations will be deleted. Additionally, it provides examples and variable definitions relevant to the software commands used in the process.

Uploaded by

Leonardo Dantas
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
51 views5 pages

Switch From Voss To Exo S

This document outlines the procedure for switching a VOSS switch to the EXOS Network Operating System, primarily using ExtremeCloud IQ or VOSS CLI commands. It details the necessary steps, including transferring the NOS image, confirming the change, and restarting the switch, while noting that all previous configurations will be deleted. Additionally, it provides examples and variable definitions relevant to the software commands used in the process.

Uploaded by

Leonardo Dantas
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

Procedure to Switch from VOSS to EXOS

For VOSS Release 8.2.5

9036812-00 Rev AA
October 2020
Copyright © 2020 Extreme Networks, Inc.

Legal Notice
Extreme Networks, Inc. reserves the right to make changes in specifications and other information
contained in this document and its website without prior notice. The reader should in all cases
consult representatives of Extreme Networks to determine whether any such changes have been
made.
The hardware, firmware, software or any specifications described or referred to in this document
are subject to change without notice.

Trademarks
Extreme Networks and the Extreme Networks logo are trademarks or registered trademarks of
Extreme Networks, Inc. in the United States and/or other countries.
All other names (including any product names) mentioned in this document are the property of
their respective owners and may be trademarks or registered trademarks of their respective
companies/owners.
For additional information on Extreme Networks trademarks, see: www.extremenetworks.com/
company/legal/trademarks

Open Source Declarations


Some software files have been licensed under certain open source or third-party licenses. End-
user license agreements and open source declarations can be found at: https://
www.extremenetworks.com/support/policies/open-source-declaration/
Table of Contents
Change the Network Operating System Personality.......................................................................................... 4

Procedure to Switch from VOSS to EXOS iii


Change the Network Operating System Personality
Use this procedure on a VOSS switch to change the Network Operating System (NOS) personality.

The primary method to select a NOS personality for the switch is by using ExtremeCloud IQ. If the
network is not accessible, or if you do not use Extreme Networks management software, you can
change the NOS personality by using VOSS CLI commands.

Before You Begin

Use FTP to transfer the NOS image to the /intflash/ directory in the VOSS file system.

About This Task

If you change the NOS personality, the system deletes all configuration, licensing, and log files that
pertain to the previous NOS personality.

If a power interruption occurs during a personality change, the system restarts the process after you
restore power to the switch.

As part of the NOS personality change, you must restart the switch. If, during the restart, the system
detects a failure, the NOS personality does not change. After the original NOS restarts, it logs an error
message and raises a persistent alarm.

Procedure

1. Enter Privileged EXEC mode:


enable
2. Unpack the NOS image:
software add WORD<1-99>
3. Install the NOS image:
software activate WORD<1-99>
4. Confirm you want to change the NOS personality by entering Y.
5. Confirm the new image has been added and will become active after the next restart:
show software

Important
If you decide not to change the NOS personality, before you restart the switch, you can run
the software activate command again with the primary release as the image name
and the system cancels the NOS personality change.

6. Restart the switch.

4 Procedure to Switch from VOSS to EXOS


Change the Network Operating System Personality Variable Definitions

Example
Change the NOS personality to ExtremeXOS.
5520-24W-VOSS:1>enable
5520-24W-VOSS:1#software add summit_arm-31.1.0.540.xos
EXOS image validated successfully
Adding EXOS software - /intflash/summit_arm-31.1.0.540.xos
Extraction of /intflash/summit_arm-31.1.0.540.xos to /intflash/release/
summit_arm-31.1.0.540.xos successful
5520-24W-VOSS:1#show software
=============================================================================
software releases in /intflash/release/
=============================================================================
summit_arm-31.1.0.540.xos
5520.v8.2.5int030 (Primary Release)

-----------------------------------------------------------------------------
Auto Commit : enabled
Commit Timeout : 10 minutes
5520-24W-VOSS:1#software activate summit_arm-31.1.0.540.xos
Executing software activate for version summit_arm-31.1.0.540.xos.
Validated EXOS software
WARNING: The specified image is for the EXOS Network Operating System and the VOSS
Network Operating System
is currently running.
If you continue, all data including configurations, logs and debugs will be cleared,
except for the license activation
status. EXOS will be installed and VOSS image files will be removed. Do you want to
continue (y/n) ?y

Variable Definitions
The following table defines parameters for the software command.

Variable Value
activate WORD<1-99> Specifies the software version to copy to the boot
flash file.
add WORD<1-99> Specifies the software version to unpack.

Procedure to Switch from VOSS to EXOS 5

You might also like