3.

1 programming instructions: (programming code factory value: 123456)

Programing name Continuose button (card reader) operation remarks

Modify the programming password # programing password # 0 new If you forget the programming password
programming password # reppit new according to 3.2 steps to restore to the
programing password 11 # factory default (123456)
Add user card # programing password # 1 reading card # For one-time add multiple user cards,
continuous reading card can be
Increase (modify) the public open # programing password # 21 new password Public opening password can only be set -
the door password # Liu password to open the door, enter the
"password", then press "#" to open the
door
Delet all users # programing password # 40 0000 # This will delete all card and password users,
but will not delete the common password
Delet user (card reader) # programing password # 41 reading card # For a one-time delete multiple user cards,
continuous reading card can be

Increase personal password to open # programing password # 22 new password Personal open the door password can set
# the multi-group; password to open the
door, the input "password", and then Press
the "5", you can open the door
Increase user card (input card # programing password # 23 handmade Card number can be induction card on
number) enter card number # space left 10-bit digital or the right of the 8-
bit digital, machine automatic identification
Increase user card (serial card # programing password # 24 handmade Card number of years must be a 4-digit
number) enter the start card number # (such as the one-off plus 20 card, should
enter 0020)
Increase “card + password” user # programing password # 3 reader new To modify and card corresponding
password # password, please refer to 3 5 steps
Delet user (input number) # programing password # 42 User ID # User ID description see 3.4 section, enter
the user ID when must be a 4-digit, such as
0001, 0020 and other
Delete user (input card number) # programing password # 43 Handmade Card number can be induction card on
enter card number # space left 10-bit digital or the right of the 8-
bit digital, machine automatic identification
 Delete user (enter password) # programing password # 44 personal open Remove the password correspond to the
the door password # user, and the password corresponding card
number also be deleted
Delete all password users # programing password # 45 1111 # All only is personal to open the door
password are delete
Modify the relat unlock time # programing password # 5 XX # "x x" for two digits, up to 99 seconds if
input 00, the relay signal moment output
(0.2 seconds)
Set the door open mode # programing password # 6 XX # "xx", may be 01 (card to open the door), 02
(card or password to open the door) or 03
"card 嘧 code to open the door)
Reader function (WG26 output) # programing password # 6 04 # This mode this machine can do reader use,
wg interface output wg26 signal (this
function only part of model)
Set safety functions # programing password # 7 XX # "x ×" can be 01 or 02 "safety features off /
on), 03 or 04 (tamper alarm off / on only
part of model)
Set the backlight mode # programing password # 8 XX # "xx" can be 01 (light normally open), 02
(light normally closed) 03 (automatic) (this
function only part of model)
Restor the machine factory # programing password # 8 99 # All the machine parameters are recovery
parameters for factory value, such as table 1.3 shows

3.2, initialization programming password (123456) and set the mother card (management card)

first step: power, the rst (s 1) jumper cap connection 2, 3-side re-power, three sound sounding after the Green light flash the programming
password recovery for factory value (123456)

the second step (such as no need to mother card, this step can be omitted): continuous brush two blank card (the first to "increase card" second
Zhang "delete card"), the Red light flashes, continuous short Ming

step 3: power, jumpers cap reconnect 1, 2-side, and finally to re-power, programming password initialization success and mother card increase
complete.

3.3 master card of use increase

user card: in standby, brush "increase card", painted to increase the user card, and then brush "increase card" exit remove
user card: in standby, brush "delete card", painted you want to delete the user card, and then brush "delete card" exit delete all users, in
standby, brush "delete card", painted "increase card", then brush "delete card" exit. This will delete all users, including personally password user
(excluding public password). Kaka use

3.4 user ID description

machine default user ID by 4-digit composition. From 0001 start per increase in a user, user ID automatically add 1; the middle of delete
individual user when the number automatically set empty, add user ID or in the last of the user number on the plus 1; execution delete all user
command (programming command 40 or use management card), the user ID from 0001 to re-start. Public open the door password not occupied
by the user ID.

3.5 modify and card

correspond to the individual open the door password: open the door mode is set to "Cagayan password to open the door", the user credit card
then enter to open the door password and Press the "#", success opened the door of 5 seconds, Press the "well," until the Green light flash, then
enter conceal area] [repeat new password] [#], the buzzer sounding a sound, and the card correspond to the individual open the door password
modify success, "