W9102

User Manual

Shenzhen SKYTEK intelligent technology co.,LTD

Getting to Know Your Mobile Hotspot

1.Power key:Hold the Power key for 3 seconds to power the device on/off.

2.WPS key: Hold the WPS key for 3 seconds to activate the WPS function. Once activated, the Wi-FiTM LED indicator will

flash every two seconds. If the network is not accessed within 2 minutes, the device will automatically exit WPS (Wi-Fi

Protected Setup) mode.

3.LED indicators: Display network signal, Wi-Fi, battery charge and mobile data status.

4.USB port: Use the USB port to charge your device via the USB cable.

5.Reset:Hold both the Power key and the WPS key simultaneously for 15 seconds. All LED indicators will flash green 4 times

to indicate that the device has been reset to factory default settings.
6.Reboot: Hold the Power key for 10 seconds to restart your device.

Insert Nano-sim

1.Remove the battery cover

2.Remove the battery

3.Insert Nano-SIM
Charging Your Mobile Hotspot

1.Connect the microUSB end of the USB cable to the USB port on your device.

2.Connect the other end to the travel adapter.

3.Connect the travel adapter to an electrical outlet to fully charge your device.

Note: You can also charge the device by connecting it to a computer with the USB cable.

Connecting Your Wi-Fi Device to Your Mobile Hotspot

1.Power on your mobile hotspot

2..On your computer or other Wi-Fi enabled device, search for available Wi-Fi networks and select network name (SSID)

located on label on back panel of your mobile hotspot.

Note: Wi-Fi name (SSID) and Wi-Fi Password are located on the label inside the back cover of the device.

*From a Windows computer: Left-click Wireless Network Connection on the task bar to view available networks. Choose the

SSID from the list of available networks.

*From a Mac computer: Select System Preferences > Network. Choose the SSID

from the list of available networks.

*From an iOS device: Go to Settings > Wi-Fi. Choose the SSID from the list of available networks.

*From an Android device: Go to Settings > Wi-Fi. Choose the SSID from the list of available networks.

3.Enter the password located on label on back panel and click OK.

Using the WPS

If your Wi-Fi device supports WPS, you do not have to input the password manually after a WPS connection has been

established. Please follow the following steps:

1.Power on your Mobile Hotspot and enable the Wi-Fi function from the device you would like to connect.

2.Press and hold the WPS key on your device for 3 seconds to start the Wi-Fi Protected Setup authentication process.

3.Enable the WPS function on your Wi-Fi device in order to respond to this authentication process.

4.Follow the system prompts on your Wi-Fi device to finish the connection.

5.If no Wi-Fi device is connected within 2 minutes, the WPS function will automatically turn off.

Managing Your Mobile Hotspot

You can access your Mobile Hotspot device information using an Internet browser or by connecting the device to a computer

via the USB cable.

Access Mobile Hotspot Using A Browser

1.Connect to your hotspot device through Wi-Fi using the network connection software on your computer. Provide the Wi-Fi
 network password, if requested.

2.Open a browser and enter http://mobile.hotspot or http://192.168.128.1 in the address bar. The Movitel Mobile Hotspot

Web User Interface screen will appear.

3.Click Login on the top right of the Web UI screen. The login screen will appear.

4.Enter your Password in the field provided. The default password is "admin".

5.Click Login. If you entered the correct password, the Web User Interface screen appears again.

Access Mobile Hotspot Using USB Cable

1.Connect your Coolpad Surf Mobile Hotspot to the computer with the USB cable.

2.Power on your device.

3.The computer operating system detects and recognizes new hardware and finishes the installation automatically.

4.Open a browser and enter http://mobile.hotspot or http://192.168.128.1 in the address bar. The Movitel Mobile Hotspot Web

User Interface screen will appear.

5.Click Login on the top right of the Web UI screen. The login screen will appear.

6.Enter your Password in the field provided. The default password is "admin".

7.Click Login. If you entered the correct password, the Web User Interface screen appears again.

Note: Windows (32 bit & 64 bit) 7/8/8.1/10, Mac OS X 10.6 to 10.11 supported.

Changing Mobile Hotspot Admin Password

1.Access http://mobile.hotspot or http://192.168.128.1.

2.Click Settings in the navigation area.

3.Select the Device tab and click Account Management.

4.Follow steps under Account Management to update your Password.

5.Click Save Changes. If everything is entered correctly, the Success message will appear indicating the password was

successfully changed.

Changing Mobile Hotspot Network Name (SSID)

1.Access http://mobile.hotspot or http://192.168.128.1.

2.Click Settings in the navigation area.

3.Select the Wi-Fi tab and click Basic.

4.Enter a new name in the Wi-Fi Name (SSID) field.

5.Click On or Off checkbox for Hide SSID to disable or enable broadcasting the hotspot’s Network Name (SSID).
6.Click Save Changes.

Changing Mobile Hotspot Wi-Fi Password

1.Access http://mobile.hotspot or http://192.168.128.1.

2.Click Settings in the navigation area.

3.Select the Wi-Fi tab and click Basic.

4.Select WPA2-PSK for the Authentication Method.

5.Enter a new password in the Wi-Fi Password field.

6.Click Save Changes.

Changing Mobile Hotspot’s Access Status

When the Access Status “Allow all devices to access with password” is selected, users will be allowed to access to

network via use of correct password. When the Access Status“Allow only users on Permitted list”is selected, only users that

have been granted access by adding a user’s MAC address will be able to connect to the network.

1.Log into the Web User Interface.

2.Go to Connected Devices > Access Permissions. The Access Status “Allow all devices to access with password” is

selected by default. Any user who inputs the correct password can access the network.

3.Select “Allow only users on Permitted list” and click Add.

4.Enter the device name and the MAC address, and click Apply to add a user to the Permitted Device List.

5.Click Save Changes.

Note: If you remove a user from the Permitted Device List, such user will no longer be allowed to connect to the network. Click

Delete to remove.

Updating Software Version

Check the software version currently installed on your mobile hotspot.

1.Access http://mobile.hotspot or http://192.168.128.1.

2.Within the Web User Interface, go to About > Firmware > Firmware Version to view which software version is currently

installed on your device.

Update your mobile hotspot to the most up-to-date software version.

3.Access http://mobile.hotspot or http://192.168.128.1.

4.Within the Web User Interface, go to Settings > Device > Software Updates.

5.Click Update Firmware to update.

Note: Do not remove the battery during software updating. This may cause the software update to fail.

For more help,

Please contact us for hot news, trends, technology, and other cool content by:

Visit: http://www.skytek.com.hk/ to contact us