TECHNICAL DATA SHEET

FOR
DRAINAGE SYSTEM
PUSH FIT JOINTING
SOLVENT WELDING IN HOT WEATHER CONDITIONS :

During hot weather conditions of 35°C and above, special consideration should be given to the process of
solvent Welding of UPVC pipes and fittings to ensure a leak proof joint.

Solvent cements contain high strength chemical solvent which evaporate faster at elevated temperatures
and in windy conditions.

When PVC pipes are stored in open areas or under direct sunlight, the pipe surface temperature will be
around 15°C higher than the ambient temperature. The solvent cement attacks the hot surface faster and
deeper. Therefore, it is very important to avoid using excess cement during the jointing process to avoid
creating pools of cement inside the fitting and pipe sockets. Excess solvent cement should be wiped off
the joined surface quickly.

Recommedations for the solvent welding during hot weather confitions:

1. Solvent cement and cleaners should be stored in a cool or shady areas.
2. Pipes and Fittings should be stored in a shady area before solvent welding
3. The surfaces to be joined should be cooled by wiping with a wet cloth. The surfaces should be dry
before applying the solvent cement.
4. Solvent welding is recommended to be done during the cooler morining hours.
5. The two surface should be joined quickly while they are still wet with cement.
6. Shake or stir the solvent cement well before use.
7. Allow at least 24 hours for the joints to cure before pressurizing the system. For sizes above 8” you
should allow at least 48 hours.
5
6
7
8
10
11
12
 40

Drainage Pipes for Above Ground Drainage

Normal Size (mm)

* Produced upon request only.

BS 5255 - mUPVC and ABS Waste Pipes

Normal Size (mm)

DIN19531 - 10; uPVC Pipes for Drainage Systems Inside Buildings

Normal Size (mm)

50 mm 50.00 50.20
75 mm 75.00 75.30

13
 *
* *
* *
*

* *
* *

* *

*
*

*
*

* Available in UPVC and ABS

14
 *
*

40 75
* 43 50
50 75
* 56 50
75 89
82 77
110 88
160 95
200 100

* Available in UPVC and ABS

15
 50 mm seal depth

160 mm

40 70

16
 Material : ABS

17
18
19
 40

40 40 113
125

170

430

40 40 130 40 40 164
137 183
174
238

440 660

75 50 212 40 40 164
110 75 276 174

215

560

20
 191 40 110
110
236
131

50 110

75 131

50 40 124
143

110 75 175

110 75 50 171
110 75 40 171

21
 40 75
43 50
50 75
56 50
75 89
82 77
110 88
160 95
200 100

40
50
56
75

75

22
 Material.

75
40

U D

Note : 40mm, 50mm, 75mm & 82mm sizes according to BSEN1329 can be produced in orange colour.

Fittings

40 40 40 113
50 50 50 125
56 56 56 133

40 40 130
50 50 137
56 56 174
146

23
40 40 164
50 50 183
75 50 212
56 56 203
110 75 276
238

50 50 174
56 56 169
75 50 191
215
50 188
236

40 110 50 110
50 110 75 131
56 108 82 115
131

50 40 124
75 50 143
82 56 110
175

275
370

24
 40 75
50 75
56 50
89
77
88
95
100

40 48
50 50
56
75

25
 50 101
137

50 86 50 52

50 106

50 125

26
75 50 50 75
75 86

27
 Long P Trap Solvent

240 276 466

28
Straight Offset WC Connector

F(mm)
20
110 110 128 40
D D

H
H

D1 D1

29
COSMOPLAST UPVC INSPECTION CHAMBERS
Inspection chambers are necessary in every drainage installation for inspection, testing
and removal of solids from the drainage system. Cosmoplast Inspection Chamber
provides access to the drainage system allowing rodding in both directions.

DEPTH ADJUSTMENT:
The chamber depth can easily be accommodated by installing the chamber risers one
over the other to achieve the desired height. The last chamber riser can be trimmed to
suit the finished ground level.

COMPONENTS :

30
 Perforated & Slotted Pipes

a) Perforated Pipes
Cosmoplast produces wide range of perforated uPVC pipes for Sub-soil drainage applications.
The below sketches show the general configurations which may vary depending on size and
class of pipe to be perforated.

Parameters Limits of Variation

D 32mm to 630mm in
Outside diameter
standard sizes

t In accordance with the class

Wall thickness
of pipes selected

Longitudinal p 30mm to 200mm depending

pitch of holes on size and class of pipe

3mm to 10mm depending

Hole Diameter d
on size and class of pipe

Number of rows n 1 to 4

Angular pitch a 40 degrees for 3 or 4 rows

of holes 40, 80 or 120 degrees for 2 rows

Straight rows

a °
40
40° p
D

40
°

t
n:4
d

Staggered rows

p p

n:4

31
33
b) Slotted pipes
Cosmoplast produces wide range of SLOTTED uPVC pipes for Sub-soil and Land drain
Cosmoplast uPVC slotted pipes have two rows of circumferential slots which are machine
cut and staggered, the slots are cut at an angle of 45° to give a large open area free to carry
water. Pipes are slotted to give maximum infiltration as detailed below.

A
75 75 75 75 75

Nominal Dia
SLOT WIDTH 2 TO 4mm
A

45°
Slo
tL
en
gt
h

120

32
 Certificate of Registration
QUALITY MANAGEMENT SYSTEM - ISO 9001:2008

This is to certify that: Cosmoplast Industrial Co LLC

Industrial Area No 1

Kitem ™
Sharjah
6032
United Arab Emirates
ark L
ic
No. KM

This
is to
certify
5904
23 ence
that:

e
icenc
Cosm
Holds Certificate No: FM 75767 Branch oplast

rk L
In
™ ICAD of Abu Dh dustria
LLC and operates a Quality Management System which complies with the requirements of ISO 9001:2008 for the l Co

ema
abi 1
Co Abu Dh LLC
rial following scope:
Unite abi
dust
Kit st In d Ara
b Em
opla Dhabi 1 Holds irates
22 Cosm of Abu Kitema
5904 Bran
ch
Development, Manufacture and Sale of Pipeline System Products covering: rk Lic
ence
KM
No.
Polyvinyl Chloride (PVC) Pipes and Fittings Numb
In res er:
t: ICAD abi tes Polyethylene (PE) Pipes and Fittings pec
tify tha Abu
Dh Emira Cross linked Polyethylene (PEX) Pipes and Fittings
BS EN t of:
KM 59
is to cer d Arab Plasti 1401-1 0423
This Unite Poly Propylene (PP) Pipes and Fittings Unpla cs piping
Pre Insulated Pipes and Fittings sticiz sy
ed po stems for
Glass Reinforced Plastic (GRP) Pipes and Fittings ly(vin
e
This
issu yl ch non-pres
in th govern es the righ loride su
22 th ing the )(PVC re unde
) wi t and
5904 ture "Condi use Licenc -U) rgrou
nd
KM pera tion
s"). All of the e to drain
tem itions define Kitema use the age
er: high Cond The use rk, as Kitema and
Numb and and (the of the
d ter
ms in may rk sewe
rage
ence (low VC-U) Terms Ltd above this Lic be upd in accord
Lic rge ark ce UK addres Kitemark ence ance -
emark scha ide) (P Kitem Assuran s. is aut shall ated
from with
ste diyl chlor
Kit horize have the Kite
Holds with
the BSI d in res the sam time to
d wa ance e by itions. m the Certificate No: FM 75767 time mark
so il an poly(vin ord tim Co nd or fro For and on behalf of BSI: pect
of the e me
aning by BSI Terms
of: r d in acc to
ed at
and
pect -1 stems fo asticize emark from
time
ing as
in the
provid Frank Lee, EMEA Compliance & Risk Director
Produc as in
the Con Assurance Conditi
In res 1329 sy pl Kit an ce
t(s) det
ditions UK Ltd ons
un ted Location Registered Activities ailed
BS EN pipingcture - the da e me Lic en .
tic to use be up the sam this on this (the
Plas ing stru ence may have led on Licenc
e pro
d Lic , as shall detai Original Registration
Cosmoplast Industrial Date:
Co LLC04/06/2003 Development, Effective Date:
Manufacture and 26/05/2015
Sale of Pipeline System
build ht an emark ence ct(s) vided
at or
rig Kit s Lic Produ Industrial Area NoDate:
1 Products covering: from
s the of the ms in thi of the Latest Revision 20/05/2015 Expiry Date: 26/05/2018 the
issue use pect Sharjah Polyvinyl Chloride (PVC) Pipes and Fittings
This the ed ter in res
rning ). All defin rized 6032 Polyethylene (PE) Pipes and Fittings
Page: 1 of 2 For and
gove autho
itions" ark is United Arab Emirates on beh
"Cond Kitem alf of
BSI:
of the Cosmoplast Industrial Co LLC Development, Manufacture and Sale of Pipeline System
use
The dress. Branch of Abu Dhabi 1 Products covering:
e ad First
abov Polyvinyl Chloride (PVC) Pipes and Fittings Issued Gary
ICAD : 19/ Fenton
Polyethylene (PE) Pipes and Fittings 08/ 2014 , Global
Abu Dhabi
Cross linked Polyethylene (PEX) Pipes and Fittings Assura
or United Arab Emirates nce Dir
Direct Poly Propylene (PP) Pipes and Fittings ector
ance Latest
l Assur Pre Insulated Pipes and Fittings Issue:
Globa Glass Reinforced Plastic (GRP) Pipes and Fittings 12/11/
Fe nton, First
Issued
2014
Gary This certificate was issued electronically and remains the property of BSI and is bound by the conditions of contract.
: 19/
An electronic certificate can be authenticated online. 08/
/2014 2014
12/11 Printed copies can be validated at www.bsi-global.com/ClientDirectory or telephone +971 (4) 3364917.
of BSI: Iss ue:
half Lates
t 5
d on be 1 of Information and Contact: BSI, Kitemark Court, Davy Avenue, Knowlhill, Milton Keynes MK5 8PP. Tel: + 44 845 080 9000
Latest
For an Page Issue:
This
5
BSI Assurance UK Limited, registered in England under number 7805321 at 389 Chiswick High Road, London W4 4AL, UK. Licen
To chec ce rem 12/11/
14 1 of k its ains 2014
/08/20 Page
Informa validity the prop
d: 19 /2014 telep erty of Page
BSI Assution and hone
+44 The British
Issue 12/11 A mem rance UK contact: (0)845 1 of
First : Standard
BSI, 4
Issue
ber of Limi 080 9000
t the BSI ted, regis Kitemark s Insti
tution
Lates Grou tere Cour
p of Com d in Engl t, Davy and shal
l be retu
panies. and unde Avenue, rned
r num Know immedia
ber 7805 lhill, Milto tely upon
321, n Page
at 389 Keynes MK5 request.
/2014 1 of
est. Chiswick
requ 8PP.
upon
19/08 High Tel: 4
tely
9000. Road +44 845
ued:
edia , Lond
imm 080 , UK. on, W4080 9000
Iss rned 845
First +44 , W4 4AL 4AL, .
be retu UK.
shall 8PP.
Tel:
London
and MK5 Road,
itution nes
s Inst on Key wick High
dard
Stan ill, Milt 389 Chis
British9000 Knowlh 1, at
of The nue, 532
erty (0)845 080 Davy Ave ber 780
the prop
ne +44
rt,
under
num
remainstelepho k Cou
Kitemarin England
Licence
This ck its valid
ity
: BSI,
stered No. KM
contact regi panies.
To che and Limited, of Com 5904
tion
Informa rance
Assu of the
UK
BSI
Group 23
BSI ber
A mem
BS EN
1401
-1:20
09 -
Plasti
) Unpla c piping
ture Pipes sticiz sys
pera ed po tems for
tem ly(vin no
high VC-U). yl ch n-pressu
and (P 110mm loride re
(low loride) , 160 ) (PV undergr
arge ch mm, C-U). ound
disch ly(vinyl All pip 200 mm, draina
waste po es are 250mm ge an
22 il and sticized design , 315 d sew
5904 so pla Pipes ated mm and erage
KM ms for - un manuf SN 4/S 400mm .
No. syste ucture mm DR 41
315 acture dia
pipingilding str and d fro for use meter
stics 0mm m Int in app socket
- Pla in the
bu m, 25 erplas lication ed pip
00 200m t Co areas es.
-1:20 with mm, Original Registration Date: 04/06/2003 Effective Date: 26/05/2015 Ltd ma U and
1329 160 terial
mm, T3(m UD.
BS EN 140 Latest Revision Date: 20/05/2015 Expiry Date: 26/05/2018 ).
mm,
125
0 mm,
11
mm, Page: 2 of 2
, 100
90 mm This certificate was issued electronically and remains the property of BSI and is bound by the conditions of contract.
mm, An electronic certificate can be authenticated online.
Pipes , 82
, 56mm es. Printed copies can be validated at www.bsi-global.com/ClientDirectory or telephone +971 (4) 3364917.
, 43mm ted pip BD.
36mm ter socke and
as B Information and Contact: BSI, Kitemark Court, Davy Avenue, Knowlhill, Milton Keynes MK5 8PP. Tel: + 44 845 080 9000
diame on are
plicati
in ap BSI Assurance UK Limited, registered in England under number 7805321 at 389 Chiswick High Road, London W4 4AL, UK.
For use

First
Issued
: 19/
08/201
4

5 Latest
2 of This
Iss ue:
/2014 Page Lice
To chec nce rem 12/11/
12/11 k its ains
validity the prop
2014
: Informa
t Issue BSI Assution and
telep
hone
erty of
+44 The British
Lates A mem rance UK contact:
ber of BSI,
(0)845 Standard
080 9000
Limi
the BSI ted, regi Kitemark s Inst
itution
Grou ster Cou and shal
p of Comed in Eng rt, Davy
panies. land und Avenue, l be retu
/2014
est. er num Knowlhi rned
requ immedia
upon ber 7805 ll, Milto
19/08 tely
9000. 321, n
at 389 Keynes MK5
tely upon
Page
d: edia request.
Issue
imm 080 , UK. Chiswick 2 of
rned 845 8PP.
First shall
be retu Tel:
+44 , W4 4AL High Tel:
Road, +44 845 4
and 8PP. d, London Lond
itution MK5
nes High Roa on, W4080 9000
s Inst .
dard on Key wick 4AL,
UK.
Stan ill, Milt 389 Chis
British9000 Knowlh 1, at
of The nue, 532
erty (0)845 080 Davy Ave ber 780
the prop
ne +44 Court, under
num
remainstelepho mark England
Licence ity , Kite
This ck its valid : BSI stered in ies.
contact regi pan
To che and Limited, of Com
tion
Informa rance
UK Group
BSI
Assu of the
BSI ber
A mem

34
Version 1 / Issue 10 / November 2015
Kitemark Licence
™

No. KM 603199 No. KM 603199

This is to certify that: Cosmoplast Industrial Co LLC BS EN 1519-1:2000 - Plastic piping systems for soil and waste discharge within the
Branch of Abu Dhabi 1 building structure. Polyethylene (PE).
ICAD
Abu Dhabi
Pipe sizes: 32, 40, 50, 56, 63, 75, 80, 90, 100, 110, 125, 160, 200, 250 and 315 mm.
United Arab Emirates
Pipe series: S 12.5, Application area: BD.

Pipe series: S 16, Application area: B.

Holds Kitemark Licence Number: KM 603199

In respect of:
BS EN 1519
Plastics piping systems for soil and waste discharge (low and high temperature) within the
building structure Polyethylene (PE)

This issues the right and Licence to use the Kitemark in accordance with the Kitemark Terms and Conditions
governing the use of the Kitemark, as may be updated from time to time by BSI Assurance UK Ltd (the
"Conditions"). All defined terms in this Licence shall have the same meaning as in the Conditions.

The use of the Kitemark is authorized in respect of the Product(s) detailed on this Licence provided at or from the
above address.

For and on behalf of BSI:

Gary Fenton, Global Assurance Director

First Issued: 12/11/2014 Latest Issue: 12/11/2014

Page 1 of 2 First Issued: 12/11/2014 Latest Issue: 12/11/2014

First Issued: 12/11/2014 Latest Issue: 12/11/2014

Page 2 of 2
Page 1 of 2

This Licence remains the property of The British Standards Institution and shall be returned immediately upon request.
This Licence remains the property of The British Standards Institution and shall be returned immediately upon request. To check its validity telephone +44 (0)845 080 9000
To check its validity telephone +44 (0)845 080 9000
Information and contact: BSI, Kitemark Court, Davy Avenue, Knowlhill, Milton Keynes MK5 8PP. Tel: +44 845 080 9000.
Information and contact: BSI, Kitemark Court, Davy Avenue, Knowlhill, Milton Keynes MK5 8PP. Tel: +44 845 080 9000. BSI Assurance UK Limited, registered in England under number 7805321, at 389 Chiswick High Road, London, W4 4AL, UK.
BSI Assurance UK Limited, registered in England under number 7805321, at 389 Chiswick High Road, London, W4 4AL, UK. A member of the BSI Group of Companies.
A member of the BSI Group of Companies.
 Kitemark Licence
™

No. KM 603199 No. KM 603199

This is to certify that: Cosmoplast Industrial Co LLC BS EN 1519-1:2000 - Plastic piping systems for soil and waste discharge within the
Branch of Abu Dhabi 1 building structure. Polyethylene (PE).
ICAD
Abu Dhabi
United Arab Emirates Pipe sizes: 32, 40, 50, 56, 63, 75, 80, 90, 100, 110, 125, 160, 200, 250 and 315 mm.

Pipe series: S 12.5, Application area: BD.

Pipe series: S 16, Application area: B.

Holds Kitemark Licence Number: KM 603199

In respect of:
BS EN 1519
Plastics piping systems for soil and waste discharge (low and high temperature) within the
building structure Polyethylene (PE)

This issues the right and Licence to use the Kitemark in accordance with the Kitemark Terms and Conditions
governing the use of the Kitemark, as may be updated from time to time by BSI Assurance UK Ltd (the
"Conditions"). All defined terms in this Licence shall have the same meaning as in the Conditions.

The use of the Kitemark is authorized in respect of the Product(s) detailed on this Licence provided at or from the
above address.

For and on behalf of BSI:

Gary Fenton, Global Assurance Director

First Issued: 12/11/2014 Latest Issue: 12/11/2014

Page 1 of 2
First Issued: 12/11/2014 Latest Issue: 12/11/2014 First Issued: 12/11/2014 Latest Issue: 12/11/2014

Page 1 of 2 Page 2 of 2

This Licence remains the property of The British Standards Institution and shall be returned immediately upon request. This Licence remains the property of The British Standards Institution and shall be returned immediately upon request.
To check its validity telephone +44 (0)845 080 9000 To check its validity telephone +44 (0)845 080 9000
Information and contact: BSI, Kitemark Court, Davy Avenue, Knowlhill, Milton Keynes MK5 8PP. Tel: +44 845 080 9000. Information and contact: BSI, Kitemark Court, Davy Avenue, Knowlhill, Milton Keynes MK5 8PP. Tel: +44 845 080 9000.
BSI Assurance UK Limited, registered in England under number 7805321, at 389 Chiswick High Road, London, W4 4AL, UK. BSI Assurance UK Limited, registered in England under number 7805321, at 389 Chiswick High Road, London, W4 4AL, UK.
A member of the BSI Group of Companies. A member of the BSI Group of Companies.

45
EN 1519-1
R
R

42
uPVC BELL MOUTH SOCKET

B B

L
OD OD

114.1 145

168.0

218.8

272.6 330

uPVC PUDDLE FLANGE

B
L
W
L1
A

W D
D

3
uPVC SAND TRAP

BUCKET HANDLE

D A

C B

Dimensions:
A : mm
B : mm
C : mm
D : mm
E : mm

Perforation Details :

Others :

4
LONG RADIUS BEND

Pipe Size (OD - MM) Radius - R (MM) Angle

Socket Type : Solvent Rubber

End Type : Solvent Spigot

Others :

5
GULLY TRAP

D2 H1
D3

H2 H3

Specifications:
D : mm
D2 : mm
D3 : mm
H1 : mm
H2 : mm
H3 : mm
Requires

Separator :
D2 Side
D3 Side
Top Cover:
Grated Cover
Close Cover with Bolts and Nuts

Other :

6
7
Sizes of Grease Trap

Type D

8
9
10
 *applicable for Pex Pipe
R

Version 2 - Issue 3 - December. 2018

 Data sheet
ACO grease trap AGT-40
Grease separator for commercial kitchens ► Stainless steel

ACO grease trap AGT-40

Introduction

Introduction Benefits

Designed for below-sink use in commercial kitchens and other §§ Protection of inner pipes against clogging
food service establishments, ACO’s AGT-40 grease trap §§ Space and cost effective solution
prevents grease and food debris from entering waste water §§ Biological dosing possibility
and as result, ensures that inner pipework is protected. §§ Quick and easy installation
It is suitable for use in areas where large grease separator §§ Easy maintenance with no barriers inside
cannot be installed and delivers the following benefits. §§ Maximized separation chamber to increase separation
efficiency

Typical application include:

Kitchens Restaurants Fast food restaurants Hotels Cafeteria

ACO grease trap AGT-40

Page 1 of 7
Data sheet
ACO grease trap AGT-40
Grease separator for commercial kitchens ► Stainless steel

ACO grease trap AGT-40

Main advantages

INBUILT FLOW REDUCER ODOUR PROOF

overflow protection hygienic kitchen enviroment
max flow up to 0,6 l/s

STAINLESS STEEL FLEXIBLE COUPLINGS

simple installation
hygienic solution
2 different rubber connections
available as accessories!
MOBILE vs STATIONARY
convenient maintenance

DRAIN VALVE & SLOPED BOTTOM

easy maintenance

Set of wheels
available as accessories!

Guide

Regular maintenance of grease trap

In the kitchen STATIONARY Out of the kitchen MOBILE
(Leveling legs are included) (Wheels on request as additional accessory)

Inlet/Outlet rubber connection on request Item number Inlet/Outlet rubber connection on request Item number

2“ | 48-60 mm 136807 2“ | 48-60 mm 136807

11/2“ | 38-50 mm 136808 11/2“ | 38-50 mm 136808

ACO grease trap AGT-40

Page 2 of 7
 Data sheet
ACO grease trap AGT-40
Grease separator for commercial kitchens ► Stainless steel

ACO grease trap AGT-40

Technical data

Material 1.4301 (AISI 304)

Length: 540 mm

Product dimensions Width: 400 mm

Height: 333-353 mm

Product weight (full tank) 18 kg (60 Kg)

Effective volume of tank 42 litres

Strainer basket capacity 5 litres

§§ Made from stainless steel grade 1.4301 (AISI 304)

§§ Smooth cleanable surface and easy removable fully accessible
airtight cover for inspection and maintenance
§§ Levelling feet for floor slope correction and hygienic installation
§§ Drain valve 1“ for easy draining
§§ No need to install any additional P-trap on outlet pipe which usually
cause overflow problem during operation because the separator has
its own in-built air trap on outlet side

AGT-40 - Undersink Grease Trap

Item name Description Item number

AGT-40 §§ Grease trap incl. sediment bucket

Undersink Grease Trap §§ Removable, airtight, full access cover
§§ Leveling legs 136806
Flexible couplings need to be §§ Drain valve
ordered as accessories!

Accessories

Item name Description Item number

Wheels §§ Set of caster wheels (4pcs) for AGT-40 Under

Sink grease trap
136804

Height adjustable stand §§ Stand for under sink grease trap 400 x 540
x 310 mm
136805
§§ Adjustable height 120 - 175 mm
§§ Stainless steel grade 1.4301 (AISI304)

Rubber connection §§ 1 piece 1 1/2” (38 - 50 mm)

(flexible couplings)
136808

Rubber connection §§ 1 piece 2” (48 - 60 mm)

(flexible couplings)
136807

ACO grease trap AGT-40

Page 3 of 7
 8 7 6 5 4 3 2 1

400
540
F F
A

Page 4 of 7
ACO grease trap AGT-40
Data sheet

333 - 353
E E
ACO grease trap AGT-40

9 11 A

761,7
(185,2) 2
(36,5)
D 13 7 (104,5) D
A-A ( 1 : 5 )
B

4
1

C C

14

For one trap you need to order 2 pcs.

of rubber connections.
B B
2 variants:
136807 - 2" | 48-60 mm
Pos. Description Mat. 136808 - 1 1/2" | 38-50 mm
1 Grease trap box
2 Grease trap top cover AISI 304 Surface Treatment: Pickling & Passivation
3 Sediment bucket AISI 304
4 Cover for outlet chamber AISI 304 Revision History
Grease separator for commercial kitchens

5 EPDM Gasket L=537 Rubber Zone Rev. Description Date Revised by

►

6 EPDM Gasket L=367 Rubber A Partial redesign - inlet, outlet, rubber, clamps, .. 4/6/2018 bhaupt
7 UPVC Pipe 1-1/2", L50mm PVC-Piping Designed by Creation Date Revised by Revision Date Material Article Number
8 Washer M6 AISI316 kjanacek 8/5/2017 bhaupt 4/6/2018 136806
9 Nut M8, DIN934 AISI316 All ACO drainage design in this drawing are Intellectual Property Description
of ACO. Copying and Distribution of this design must have written AGT-40
A 10 Bolt M6x12, DIN912, A4 AISI 316 permission from designer.
A
11 Leveling foot: stainless steel + technopolymer AISI 304
Under Sink Grease Trap 400x540x310,
ACO Systems FZE
Office/Warehouse
LX.40-SW17-M8x30 - Elesa+Ganter Jebel Ali Freezone 2x 2" connection, AISI304
Plot S10511
P.O. Box 18672, Dubai, UAE
13 UPVC Female elbow 1-1/2" PVC-Piping Tel No. +971 4 880 69 98 Drawing no. Mass Revision Sheet
Fax No. +971 4 880 69 97
Stainless steel

14 Website:http://www.aco.ae/ 1 /17
Brass Ball Valve 1" Brass DX08-00004 N/A A
8 7 6 5 4 3 2 1
 Data sheet
ACO grease trap AGT-40
Grease separator for commercial kitchens ► Stainless steel

ACO grease trap AGT-40

Grease Dosing Systems

Why biological cleaning Biological activator

When preventing the build-up of fats, oils and grease ACO´s biological activator works in two distinct ways
(FOG) in kitchen drainage systems, the grease trap can on FOG waste that settles in the drainage pipework
be used as a gravity separator, although for optimum and grease trap system:
effectiveness it should be used in combination with
a biological dosing system. 1. The activator introduces an enzyme that assists the
natural biological process of breaking down long molecular
chain FOG’s into a manageable solution which can then be
Benefits of Automatic Dosing Units discharged safely into the drainage system.

§§ Automatic control over 2. The activator introduces other micro-organisms that actively
the timing and regularity feed on the FOG’s present in the solution.
of regular dosing
§§ Low maintenance
for kitchen staff ACO activator process
§§ Precision dosing
to reduce waste

Maintenance
Enzyms break long chain molecule
FOG´s into fluid solutions
All dosing units are automatic. They require no maintenance
from kitchen staff except to replace the biological solution Active micro-organisms digest long
bottle when necessary. Professional servicing of the unit and short chain components
to check functionality and programming is recommended annually.

Dosing times

ACO Dosing ACO Dosing

Meals Meals
Clear time Clear time
per day per day
(ml) (min) (ml) (min)

50 50 0:30 250 250 2:30

100 100 1:00 300 300 3:00
150 150 1:30 350 350 3:30

An example of dosing periods for 200 meals per day

07:00 08:00 09:00 10:00 11:00 12:00 13:00 14:00 15:00 16:00 17:00 18:00 19:00 20:00 21:00 22:00 23:00 Total

ACO Clear (ml) 30 60 40 70 200 ml

Dosing Time
0:18 0:36 0:24 0:42 2:00
(min)

ACO grease trap AGT-40

Page 5 of 7
 Data sheet
ACO grease trap AGT-40
Grease separator for commercial kitchens ► Stainless steel

ACO grease trap AGT-40

Dosing of biological activators

Item name Description Item number

Main operated §§ Peristaltic pump for dosing of biological solution

dosing device §§ Dimensions: 105 x 130 x 100 mm
MODD 49025
§§ Power Supply: 100 – 240 V AC
§§ Flow Rate: 100 ml/m

ACO clear §§ Biological activator

dosing solution §§ 5 litre pack 49020

ACO clear §§ Biological activator

dosing solution §§ 20 litre pack 49022

Mounting frame §§ For clean storage of the dosing device

and packs of dosing solution 402637
§§ Dimensions: 265 x 627 x 170 mm

ACO grease trap AGT-40

Page 6 of 7
ACO Group

The family-owned company headquartered in The major innovation strength of the ACO 1946, company founded
Rendsburg/Büdelsdorf, Germany, Group is built on intense research and by Josef-Severin Ahlmann
was founded in 1946 on the site development, and its technical expertise 4 400 employees in more than
of the Carlshütte foundry in processing polymer concrete, plastic, cast 40 countries (Europe, America,
– Schleswig-Holstein’s first industrial iron, stainless steel and reinforced concrete. Asia, Australia, Africa)
company. It still has very strong roots
30 production sites in 15 countries
in the region.

ACO Products

At ACO we are committed to Building drainage

helping you bring the very
best quality products to your
customers.

ACO supports your brand at every stage

of the production process and helps you
deliver ultimate hygienic performance to
your facilities. We understand the critical
role that drainage plays in a successful
beverage industry business and we
ACO hygienic gullies ACO hygienic box channels
appreciate that what’s below
ACO hygienic gullies are available ACO hygienic box channels range is ideal
the surface can really counts.
in various body sizes to cater for for applications where high standards
sufficiend flow rates and construction of hygiene are required as they are
requirements including shallow capable of handling large volumes of
construction depths fluid. ACO hygienic box channels are
and applications where preventative fire certified according to EN 1253.
measures are required. ACO hygienic
gullies are certified according to EN
1253.

ACO pipe ACO grease separators

The stainless steel push-fit pipe system A comprehensive range addresses
ACO Systems FZE
is designed for grey, black and rain all size requirements within the EN 1825
Jebel Ali Free Zone water. ACO pipe offers 40+ years specification, with performance
Street 100, Bldg. 07 product life thanks to its material at or beyond the Standard’s requirement.
P.O. Box 18672, Dubai properties. Certified to EN 1825, CE marked.
United Arab Emirates
Easy installation and handling on site
Tel: +971 4 880 69 98
Fax: +971 4 880 69 97 is ensured by push-fit assembly system
[email protected] and available cutting tools.

ACO. creating the future of drainage

www.aco.ae