Total No. of Questions : 4] SEAT No.

8
23
PA-47 [Total No. of Pages : 3

ic-
[5931] - 73

tat
S.E. (Automobile & Mechanical Engineering/Mechanical

8s
Sandwitch/Automation & Robotics)

1:4
SOLID MECHANICS

02 91
0:4
(2019 Pattern) (Semester - I) (202041)

0
31
Time : 1 Hour] 6/0 13 [Max. Marks : 30
0
Instructions to the candidates:
1/2
.23 GP

1) Answer Q.1 or Q.2, Q.3 or Q.4.

2) Figures to the right side indicate full marks.
E

3) Use of electronic pocket calculator is allowed.

81

8
C

4) Assume Suitable data if necessary.

23
ic-
Q1) a) A 2.0 m long steel bar is having uniform diameter of 40 mm for a length
16

tat
of 1 m from one end. For the next 0.5 m length the diameter decreases
8.2

8s
uniformly to ‘d’. For the remaining 0.5 m length it has a uniform diameter
.24

1:4
of d mm. When a load of 150 k N is applied, the observed extension is
91
49

0:4
2.40 mm. Determine the diameter d. Take modulus of elasticity for steel
30

equal to 200 k N/mm2. [7]

31

b) The composite bar consisting of steel and aluminium components as

01
02

shown in Fig 1.1 is connected to two grips at the ends at a temperature

1/2
GP

of 60º C. Find the stresses in the two rods when the temperature falls to
6/0

20ºC. [8]
CE
81

8
i) if the ends do not yield.

23
.23

ii) if the ends yield by 0.25 mm.

ic-
16

Take Es = 2 × 105 and Ea = 0.7 × 105 N/mm2, αs = 1.17 ×10–5 and

tat
8.2

αa = 2.34 × 10–5 per ºC. The areas of steel and aluminium bars are 250
8s
.24

1:4

mm2 and 375mm2 respectively.

91
49

0:4
30
31
01
02
1/2
GP
6/0
CE
81
.23
16
8.2

OR
.24
49

[5931] - 73 1 P.T.O.
Q2) a) A steel block 360mm×80mm×160 mm is subjected to the following

8
23
forces. [7]

ic-
i) A tensile force of 1280KN on the 160mm×80mm faces

tat
(take as a X - direction).

8s
ii) A tensile force 3456 KN the 360mm×80mm faces

1:4
(take as a Y - direction) and.

02 91
iii) A compressive force of 5184KN on the 160mm×360mm faces

0:4
(take as a Z - direction).

0
31
6/0 13
Find the changes in the dimensions of the block and also the change
in volume. Take E = 2×105 N/mm2 and 1/m = 0.25.
0
1/2
.23 GP

b) A rigid rod ABCD is supported by a hinge at A and two wires at B and C

as shown in figure 2.1. Determine the stresses and elongation of the two
E

wires. Take Es = 200 GPa and Ec =100GPa. [8]

81

8
C

23
ic-
16

tat
8.2

8s
.24

1:4
91
49

0:4
30
31
01
02
1/2
GP
6/0

Q3) a) Draw SFD and BMD of the beam shown in figure 3.1 [7]
CE
81

8
23
.23

ic-
16

tat
8.2

8s
.24

1:4
91
49

0:4
30
31

b) Draw SFD & BMD of the beam shown in figure 3.2, also locate the
01

point of contraflexure from left end. [8]

02
1/2
GP
6/0
CE
81
.23
16
8.2
.24

OR
49

[5931] - 73 2
Q4) a) Draw SFD & BMD of the beam shown in figure 4.1. [7]

8
23
ic-
tat
8s
1:4
02 91
0:4
0
31
6/0 13
0
b) Draw SFD & BMD, of the beam shown in figure 4.2, also find the POC
1/2
.23 GP

from left end. [8]

E
81

8
C

23
ic-
16

tat
8.2

8s
.24

1:4
91
49

0:4
30
31
01
02
1/2
GP
6/0

  
CE
81

8
23
.23

ic-
16

tat
8.2

8s
.24

1:4
91
49

0:4
30
31
01
02
1/2
GP
6/0
CE
81
.23
16
8.2
.24
49

[5931] - 73 3