0% found this document useful (0 votes)
159 views6 pages

Abresh New Coc

Coc exam

Uploaded by

dotyeberihun
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
159 views6 pages

Abresh New Coc

Coc exam

Uploaded by

dotyeberihun
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 6

1.

An electric pyrometer is an instrument used to measure


a. Phase
b. Frequency
C. High temperature
d. Power
2. Ratio type control of a system mostly employed?
a. in pressure control of a system
b. in production of gas system control
C. in chloration of water system control
d. in temperature control of a furnace
3. Which of the following application software is used for electronic circuit design
a . MATLAB
b. CAD system
C. Multism
d. Logo Siemens
4. This type of fault has the same effect as an internal short between IC pins.
a Sharted signal line
b. Brocken wire
C. Open signal line
d Poor solder connection
5. Place of the proportional control used?
a. For past error control value
b. for a closed loop system only
C. to predict future error control value
d Only for fast responding work current value
6. __ receives data from measuring instrument compared that date to a programmed set point.
a. Process variable
b. Controller
C. Set variable
d. Manipulated variable
7. what does instrument date time describes
a the time for an instrument staying idle
b. the life time for an instrument
C. the time for an instrument to end reacting to process change
d. the time for an instrument to begin reacting to process change
8. What is the difference between the synchronous speed and actual speed of an induction motor?
a. Regulation
b. slip
C. back ash
d. lag
9. A situation in a system where it can never leave or progress to another state
a. No change in state
b. Hang-up state
C. Toggle
d . Reset
10. What is the function of hydraulic motor?
a. Hydraulic motor converts solar energy into hydraulic energy
b. Hydraulic motor converts hydraulic oil under pressure into force
C. Hydraulic motor converts mechanical energy into hydraulic energy
d. Hydraulic motor converts hydraulic energy into mechanical energy
11. A transduction principle used primarily in optical sensor
a. Electromagnetic transduction
b. Photoconductive transduction
C. A Photovoltaic transduction
d. Piezoelectric transduction
12. How fast should the correction applied determined
a. Derivative control mode
b. PI Control mode
C. Proportional control mode
d. Integral control mode
13. The total energy developed by the hydraulic oil in a system is given
a. Total energy=(Potential energy + pressure energy)
b. Total energy=(Potential energy - Kinetic energy)
C. Total energy=(Potential energy * kinetic energy)
d. Total energy=(Potential energy + Kinetic energy)
14. data storage in a memory is called
a. writing
b loading
C. reading
d. memorizing
15. What should be the resolution of a digital voltmeter naving a three digit 0-3?
a 3mv
b. 0 5micro volt
C. 30mV
d. 15V
16. The ratic of inertia force to viscosity
a. Cauchy number
b. Biot number
C. Euler number
d. Reynold number
17. Which one is the universal gale
a. AND gate
b. NAND gate
C. OR gate
d. NOR
18. Which one is the inverter?
a. NOT gate
b. OR gate
C. NOR
d AND gate
19. What is the meening of a 3/2 way directional valve in hydraulic control system?
a. It is a two position two port system
b. It is a three position three port system
C. It is a two position three port system
d. It is a three position two port system
20. When a problem arises while you are repairing electronic equipment that you cannot solve by yourself
a. Quit repairing
b. Throw it away
C. Vurmuring & crying
d. Ask for assistance
21. a linear IC which is mostly for amplification transducer's output
a. operational amplifier IC
b. Microcontroller IC
C. regulator IC
d. processor IC
22. What is the purpose of a comparator in op-amps?
a. To produce change in output when an input voltage equals a reference voltage
b. To detect the occurrence of a changing input voltage
C. C To amplify an input voltage
d. To maintain output when the DC input voltage changes
23. An oscillator is described by
a. Regenerative feedback
b. Unity gain and zero phase shift around the feedback loop
C. No feedback
d. An integrator or differentiator
24. What is an interface between
one-umatic and electrical totally gives the neme electro pneumatic?
a. Van type pump
b. Manual valve
C. Solenoid
d. Double acting cylinder
25. Which one is a vital link between physical quantities process and instrumentation system
a. Transducer
b. Mechatronics
C. Measurement
d. Control system
26. What do you understand the volumetric flow rate in a flow control in a hydraulic System
a. It is the volume of the fluid exist
b. It is the size of pressure exist in the given container.
C. It is the volume flow rate of a fluid per given time.
d. it is the viscosity of a fluid
27. What is the sensing element of acceleration transducer?
a. Seismic mass
b. Damper
C. Spring
d. Crystal
28. Solve for the base current if collector is 600mA and the gain is 20.
a. 12mA
b.12mA
C.3mA
d .30mA
29. which of the following part of PID control determines the length of time the correction should be applied
a. integral control mode
b. Proportional control mode
C. D control mode
d. Derivative control mode
30. Micro-controllers are __ than the PLCS
a. bulky and expensive
b. bulky but cheaper
C. portable and cheaper
d. portable but expensive
31. Find the half power bandwidth of a parallel resonant circuit which has a rescnent frequency of 3.5 MHz and
a Q of 218
a. 58.7khz
b. 16.5khz
C. 606khz
d. 47.3khz
32. If the converter unit to pulses in digital measuring instrument calibrated one pulse per volt 15 pulses
produces
a.15 VOLT
b. 30 VOLT
C. 20VOLT
d. 25 VOLT
33. The main objective of using best control system
a. Provide stability for the system
b. To differentiate input output characteristics
C. To distinguish control unit criteria
d. To be familiar with difference voltage grading
34. In distributed SCADA system common data communication is through
a. Profibus
b. PLC
C. Intelligent electronic device
d. Data bus
35. Which type of controller is acvisable where dynamics of sensor and actuator are faster compared to the
process
a Controller
b. I controller
C. PID controller
d. P controller
36. A feedback control system in which the controlled variable is mechanical position
a. Closed loop feedback control system
b. Servomechanism
C. Open loop feedback control system
d. Mechanical Servomechanism
37. What do we call that the minimum change in input value that can be detected by measuring instrument?
a. Threshold
b. Error.
C. Sensitivity
d. Resolution
38. When the inputs of a NAND gate are connected together, the resulting circuit is_
a. NOR
b. OR gate
C. AND gate
d NOT gate
39. Measuring instruments are divided in a so-called classes according to the error limit and so that the classes
of 01,02,05 and 1 are usually appointed to
A. For fine measuring instrument
b. The gross error of measuring deviation
C. For maximum relative error of in 1.5%
d. Operation electrical measuring instrument.
40. The two general types of heating methods in industrial electronics are
a. Coil and frequency heating
b. Induction and dielectric heating.
C. Frequency and induction heating
d. Coil and dielectric heating
41. What is the objective of quality control?
a. To create means to solve work related problem
b. dissatisfy customer
C. to increase the team spirit
d. to promote communication
42. What work instruction dogs it have Rec Tags in 5s?
a. Set in order
b. Sustain
C. Sort
d Standardize
43. What would be the result if the gain of controller act on KC > 0
a. Controller o/p increases, process variable decreases
b. Controller o/p and manipulated variable become less
C. Controller o/p decrease, process variable increases
d. Controller o/p and process variable equal
44. Which of the following machine or apparatus employs open loop control system?
a. A milk chilled system of industry
b. DC motor coupled with tacho generator
C. air conditioning system of a given class
d. Domestic washing machine
45. What is the purpose of taco generator?
a. Used as speed control for DC motor
b. used as analogue transducer
C. Used as protective relay
d. Used as pressure gauge
46. What distinguishes a servo motor from any other type of motor
a. it is not designed for continuous rotation it is a position seeking devise.
b. it can be manufactured both for AC and DC power supply
C. it is designed for continuous rotation of 3600and it is brushless.
d. it is simply reluctance type moto:
47. What is an automatic speed control device using the centrifugal force on rotating flyweights as the
feedback element
a. Regulator
b. Flywheel governor
C. Feld control
d. Throttle valve
48. Flow pattern gets affected when cross section of the pipe is changed?
a. laminar and turbulent
b. laminar flow
C. turbulent flow
d side flow
49. What type of control is analyzed when an operator directly manipulate the controller output to maintain set
point
a. Proportional Integral Derivative Control
b. Proportional Integral control
C. On off control
d. Manual control
50. Which component cannot be fabricated in to IC?
a Resistor
b. Transistor
C. Diode
d. Inductor
51. Refers to a design of a system taking in to account environmental and
e-ectronic characteristics access and maintainability.
a. Packaging level
b. System packaging
C. System handling
d. Packaging
52. Brushes of D.C. machines are usually made of
a. carbon
b. zinc
C. soft copper
d. hard copper
53. Certain pulse measures 10ms and has a period of 50mss.The duty cycle is
a. 5%
b. 10%
C. 100%
d. 20%
54. Which one of the fallowing is a magnetically actuated proximity switch?
a. NFN proximity switch
b. inductive proximity switch
C. Capacitive proximity switch
d. Reed proximity switch
55. Which integrated circuit is having more than 1000 gates?
a medium scale integration(NSI)
b. Very large scale integration (VLSI)
C. Small scale integration (SSI)
d. large scale integration(LSI)
56. The word measurement in instrumentation system classifies.
a. The quantities used in engineering and technology
b. The link between physical quantities electrical quantities
C. The result of process control identification
d. The comparison or unknown with known defined physical quantity.
57. ____includes two of the actuator type used in industrial robots
a. Hydraulic and Pneumatic
b. Electric and spherical
C. Hydraulic and cylindrical
d. Pneumatic and jointed arm
58. Which of the following lC processes analog signals?
a Discrete IC
b. Digital IC
C. Linear IC
d Monolithic IC
59. A digital circuit that produces an output code depending on which of its inputs is activated.
a. Decoder
b. Multiplexer
C. Encoder
d. Demultiplexer
60. Transformer cores are laminated and insulated to:
a. minimize eddy current loss
b. simplity its construction
C. Reduce hysteresis's loss
d. Reduce copper loss
61. A program which is not included in the industrial mechatronic device user program categories is called
a. Point to multi point program
b. Continuous path program
C. Point to point programs
d. Positive-stop program
62. Control system that maintain a speed voltage, or other variable within specified limits of a preset level
a Controller
b. Regulator
C. Comparator
d. Sensor
63. What sensor provides a change of resistance with typical power range of 11.W to 10mW and with
maximum frequency greater then 100GHz
a. Thermistor sensor
b. Thermal convertor
c. Thermocouple sensor
d. Diode sensor
64. The output of an inverter is connected to the input of a second inverter. Determine the output level of the
second inverter
a. Output level is the same as the input level
b. Undetermined state
C. Output level is the complement of the input level
d. High output is observed
65. How fast should the correction applied determined .
a. Derivative control mode
b. PI control mode
C . proportional control mode
d. Integral control mode
67. 1/3 times each individual resistor
68. In crease reliability a tool or equipment

You might also like