SEC1312 MICROPROCESSOR AND MICROCONTROLLERBASED SYSTEMS

UNIT 1 PREPARED BY: DR. BETTY MARTIN

MICROPROCESSOR AND MICROCONTROLLER BASED

SYSTEMS (FOR CSE & IT)
UNIT – I

INTRODUCTION TO 8085
8085 Microprocessor - Architecture and its operation, Concept of instruction execution and timing
diagrams, fundamentals of memory interface - Addressing modes

Basic Concepts of Microprocessors

Differences between: Microcomputer, Microprocessor and Microcontroller

– Microcomputer is a computer with a microprocessor as its CPU. Includes memory,

I/O etc.

– Microprocessor is a silicon chip which includes ALU, register circuits & control
circuits

– Microcontroller is a silicon chip which includes microprocessor, memory & I/O in a

single package.

What is micro?

• Micro is a new addition.

– In the late 1960’s, processors were built using discrete elements.

These devices performed the required operation, but were too large and too
slow.

– It went directly from discrete elements to a single chip. However, comparing

today’s microprocessors to the ones built in the early 1970’s you find an
extreme increase in the amount of integration.
SEC1312 MICROPROCESSOR AND MICROCONTROLLERBASED SYSTEMS
UNIT 1 PREPARED BY: DR. BETTY MARTIN

What is a microprocessor?

• The word comes from the combination of micro and processor.

• Processor means a device that processes whatever. In this context processor

means a device that processes numbers, specifically binary numbers, 0’s and 1’s.

• To process means to manipulate. It is a general term that describes all manipulation.

Again in this content, it means to perform certain operations on the numbers that
depend on the microprocessor’s design. It is a programmable device that takes in
numbers, performs on them arithmetic or logical operations according to the
program stored in memory and then produces other numbers

As a Programmable device:

• The microprocessor can perform different sets of operations on the data it receives
depending on the sequence of instructions supplied in the given program.

• By changing the program, the microprocessor manipulates the data in different

ways as Instructions, Words, Bytes, etc.

• They processed information 8-bits at a time. That’s why they are called “8-bit
processors”. They can handle large numbers, but in order to process these
numbers, they broke them into 8-bit pieces and processed each group of 8-bits
separately.

What is memory?

– Memory is the location where information is kept while not in current use. It is
stored in memory

– Memory is a collection of storage devices. Usually, each storage device holds one
bit. Also, in most kinds of memory, these storage devices are grouped into
SEC1312 MICROPROCESSOR AND MICROCONTROLLERBASED SYSTEMS
UNIT 1 PREPARED BY: DR. BETTY MARTIN

groups of 8. These 8 storage locations can only be accessed together. So, one
can only read or write in terms of bytes to and form memory.

– Memory is usually measured by the number of bytes it can hold. It is measured in

Kilos, Megas and lately Gigas. A Kilo in computer language is 210 =1024. So, a
KB (KiloByte) is 1024 bytes. Mega is 1024 Kilos and Giga is 1024 Mega.

– When a program is entered into a computer, it is stored in memory. Then as the

microprocessor starts to execute the instructions, it brings the instructions from
memory one at a time.

– Memory is also used to hold the data.

– The microprocessor reads (brings in) the data from memory when it needs it and
writes (stores) the results into memory when it is done.

A MICROPROCESSOR-BASED SYSTEM

From the above description, we can draw the following block diagram to represent a
microprocessor-based system as shown in fig 1

Fig.1. Microprocessor based system (organization of microcomputer)

SEC1312 MICROPROCESSOR AND MICROCONTROLLERBASED SYSTEMS
UNIT 1 PREPARED BY: DR. BETTY MARTIN

In this system, the microprocessor is the master and all other peripherals
are slaves. The master controls all peripherals and initiates all operations. The buses
are group of lines that carry data, address or control signals. The CPU interface is
provided to demultiplex the multiplexed lines, to generate the chip select signals and
additional control signals. The system bus has separate lines for each signal.

All the slaves in the system are connected to the same system bus. At any
time instant communication takes place between the master and one of the slaves. All
the slaves have tristate logic and hence normally remain in high impedance state. The
processor selects a slave by sending an address. When a slave is selected, it comes to
the normal logic and communicates with the processor.

The EPROM memory is used to store permanent programs and data. The
RAM memory is used to store temporary programs and data. The input device is used
to enter program, data and to operate system. The output device is also used for
examining the results. Since the speed of IO devices does not match with speed of
microprocessor, an interface device is provided between system bus and IO device.

CENTRAL PROCESSING UNIT:

The CPU consists of ALU (Arithmetic and Logic Unit), Register unit and control
unit. The CPU retrieves stored instructions and data word from memory; it also deposits
processed data in memory.

a) ALU (Arithmetic and Logic Unit)

This section performs computing functions on data. These functions are arithmetic
operations such as additions subtraction and logical operation such as AND, OR rotate
etc. Result are stored either in registers or in memory or sent to output devices.
SEC1312 MICROPROCESSOR AND MICROCONTROLLERBASED SYSTEMS
UNIT 1 PREPARED BY: DR. BETTY MARTIN

b) REGISTER UNIT:

It contains various register. The registers are used primarily to store data temporarily
during the execution of a program. Some of the registers are accessible to the uses
through instructions.

c) CONTROL UNIT:

It provides necessary timing & control signals necessary to all the operations in the
microcomputer. It controls the flow of data between the p and peripherals (input, output
& memory). The control unit gets a clock which determines the speed of the p.

The CPU has three basic functions

• It fetches an instructions word stored in memory.

• It determines what the instruction is telling it to do.(decodes the instruction)
• It executes the instruction. Executing the instruction may include some of the
following major tasks.
o Transfer of data from reg. to reg. in the CPU itself.
o Transfer of data between a CPU reg. & specified memory location.
o Performing arithmetic and logical operations on data from a specific
memory location or a designated CPU register.
o Directing the CPU to change a sequence of fetching instruction, if
processing the data created a specific condition.
o Performing housekeeping function within the CPU itself inorder to
establish desired condition at certain registers.
o It looks for control signal such as interrupts and provides appropriate
responses.
SEC1312 MICROPROCESSOR AND MICROCONTROLLERBASED SYSTEMS
UNIT 1 PREPARED BY: DR. BETTY MARTIN

o It provides states, control, and timing signals that the memory and
input/output section can use.

There are three buses:

Address Bus:

It is a group of wires or lines that are used to transfer the addresses of Memory or
I/O devices. It is unidirectional. In Intel 8085 microprocessor, Address bus was of 16
bits. This means that Microprocessor 8085 can transfer maximum 16 bit address which
means it can address 65,536 different memory locations. This bus is multiplexed with 8
bit data bus. So the most significant bits (MSB) of address goes through Address bus
(A7-A0) and LSB goes through multiplexed data bus (AD0-AD7).

Data Bus:

Data Bus is used to transfer data within Microprocessor and Memory/Input or

Output devices. It is bidirectional as Microprocessor requires to send or receive data.
The data bus also works as address bus when multiplexed with lower order address
bus. Data bus is 8 Bits long. The word length of a processor depends on data bus, thats
why Intel 8085 is called 8 bit Microprocessor because it have an 8 bit data bus.

Control Bus:

Microprocessor uses control bus to process data that is what to do with the
selected memory location. Some control signals are Read, Write and Opcode fetch etc.
Various operations are performed by microprocessor with the help of control bus. This is
a dedicated bus, because all timing signals are generated according to control signal.
The microprocessor is the master, which controls all the activities of the system. To
perform a specific job or task, the microprocessor has to execute a program stored in
memory. The program consists of a set of instructions stored in consecutive memory
location. In order to execute the program the microprocessor issues address and control
SEC1312 MICROPROCESSOR AND MICROCONTROLLERBASED SYSTEMS
UNIT 1 PREPARED BY: DR. BETTY MARTIN

signals, to fetch the instruction and data from memory one by one. After fetching each
instruction it decodes the instruction and carries out the task specified by the instruction.

Memory

To execute a program:

• The user enters its instructions in binary format into the memory.

• The microprocessor then reads these instructions and whatever data is needed
from memory, executes the instructions and places the results either in memory
or produces it on an output device.

The three cycle instruction execution model

• To execute a program, the microprocessor “reads” each instruction from

memory, “interprets” it, then “executes” it.

• To use the right names for the cycles

• The microprocessor fetches each instruction, decodes it, and then executes it.
This sequence is continued until all instructions are performed.

The 8085 Machine Language

The 8085 (from Intel) is an 8-bit microprocessor. The 8085 uses a total of
246 bit patterns to form its instruction set. These 246 patterns represent only 74
instructions. The reason for the difference is that some (actually most) instructions have
multiple different formats. Because it is very difficult to enter the bit patterns correctly,
they are usually entered in hexadecimal instead of binary.

For example, the combination 0011 1100 which translates into “increment the number in
the register called the accumulator”, is usually entered as 3C.
SEC1312 MICROPROCESSOR AND MICROCONTROLLERBASED SYSTEMS
UNIT 1 PREPARED BY: DR. BETTY MARTIN

Assembly Language

Entering the instructions using hexadecimal is quite easier than entering the binary
combinations. However, it still is difficult to understand what a program written in
hexadecimal does. So, each company defines a symbolic code for the instructions.

These codes are called “mnemonics”.

The mnemonic for each instruction is usually a group of letters that suggest the
operation performed.

• Using the same example from before,

00111100 translates to 3C in hexadecimal (OPCODE)

Its mnemonic is: “INR A”.

INR stands for “increment register” and A is short for accumulator.

It is important to remember that a machine language and its associated assembly

language are completely machine dependent. In other words, they are not transferable
from one microprocessor to a different one.

Assembling” The Program

How does assembly language get translated into machine language?

– There are two ways:

– 1st there is “hand assembly”.

• The programmer translates each assembly language instruction into its

equivalent hexadecimal code (machine language). Then the hexadecimal code is
entered into memory.

• The other possibility is a program called an “assembler”, which does the

translation automatically.
SEC1312 MICROPROCESSOR AND MICROCONTROLLERBASED SYSTEMS
UNIT 1 PREPARED BY: DR. BETTY MARTIN

8085 MICROPROCESSOR ARCHITECTURE

Features of 8085

• 8-bit general purpose µp

• Capable of addressing 64 k of memory

• Has 40 pins as shown in fig 2

• Requires +5 v power supply

• Can operate with 3 MHz clock

• 8085 upward compatible

Pin Diagram of 8085

Fig .2 Pin Diagram of 8085

A8 - A15 (Output 3 State)

Address Bus:The most significant 8 bits of the memory address or the 8 bits of the I/0
address,3 stated during Hold and Halt modes.
SEC1312 MICROPROCESSOR AND MICROCONTROLLERBASED SYSTEMS
UNIT 1 PREPARED BY: DR. BETTY MARTIN

AD0 - AD7 (Input/Output 3state)

Multiplexed Address/Data Bus; Lower 8 bits of the memory address (or I/0 address)
appear on the bus during the first clock cycle of a machine state. It then becomes the
data bus during the second and third clock cycles. 3 stated during Hold and Halt
modes.

ALE (Output) Address Latch Enable

It occurs during the first clock cycle of a machine state and enables the address to get
latched into the on chip latch of peripherals. The falling edge of ALE is set to guarantee
setup and hold times for the address information. ALE can also be used to strobe the
status information. ALE is never 3stated.

SO, S1 (Output)

Data Bus Status. Encoded status of the bus cycle: S1 S0 0 0 HALT 0 1 WRITE 1 0
READ 1 1 FETCH S1 can be used as an advanced R/W status.

RD (Output 3state)

READ: indicates the selected memory or 1/0 device is to be read and that the Data Bus
is available for the data transfer.

WR (Output 3state)

WRITE: Indicates the data on the Data Bus is to be written into the selected memory
or 1/0 location. Data is set up at the trailing edge of WR. 3 stated during Hold and Halt
modes.

READY (Input)

If Ready is high during a read or write cycle, it indicates that the memory or
peripheral is ready to send or receive data. If Ready is low, the CPU will wait for Ready
to go high before completing the read or write cycle.

HOLD (Input)
SEC1312 MICROPROCESSOR AND MICROCONTROLLERBASED SYSTEMS
UNIT 1 PREPARED BY: DR. BETTY MARTIN

It indicates that another Master is requesting the use of the Address and Data
Buses. The CPU, upon receiving the Hold request will relinquish the use of buses as
soon as the completion of the current machine cycle. Internal processing can continue.
The processor can regain the buses only after the Hold is removed. When the Hold is
acknowledged, the Address, Data, RD, WR, and IO/M lines are stated.

HLDA (Output)

HOLD ACKNOWLEDGE indicates that the CPU has received the Hold request
and that it will relinquish the buses in the next clock cycle. HLDA goes low after the
Hold request is removed. The CPU takes the buses one half clock cycle after HLDA
goes low.

INTR (Input)

INTERRUPT REQUEST is used as a general purpose interrupt. It is sampled only

during the next to the last clock cycle of the instruction. If it is active, the Program
Counter (PC) will be inhibited from incrementing and an INTA will be issued. During
this cycle a RESTART or CALL instruction can be inserted to jump to the interrupt
service routine. The INTR is enabled and disabled by software. It is disabled by Reset
and immediately after an interrupt is accepted.

INTA (Output)

INTERRUPT ACKNOWLEDGE: is used instead of (and has the same timing as) RD
during the Instruction cycle after an INTR is accepted. It can be used to activate the
8259 Interrupt chip or some other interrupt port.

RESTART INTERRUPTS: These three inputs have the same timing as INTR except
they cause an internal RESTART to be automatically inserted. RST 7.5 ~~ Highest
Priority RST 6.5 RST 5.5 Lowest Priority

TRAP (Input)
SEC1312 MICROPROCESSOR AND MICROCONTROLLERBASED SYSTEMS
UNIT 1 PREPARED BY: DR. BETTY MARTIN

Trap interrupt is a nonmaskable restart interrupt. It is recognized at the same time as

INTR. It is unaffected by any mask or Interrupt Enable. It has the highest priority of any
interrupt.

RESET IN (Input)

Reset sets the Program Counter to zero and resets the Interrupt Enable and HLDA
flipflops. None of the other flags or registers (except the instruction register) are
affected The CPU is held in the reset condition as long as Reset is applied.

RESET OUT (Output)

Indicates CPU is being reset also used as a system RESET. The signal is
synchronized to the processor clock.

X1, X2 (Input)

Crystal or R/C network connections to set the internal clock generator X1 can also
be an external clock input instead of a crystal. The input frequency is divided by 2 to
give the internal operating frequency.

CLK (Output)

Clock Output for use as a system clock when a crystal or R/ C network is used as
an input to the CPU. The period of CLK is twice the X1, X2 input period.

IO/M (Output)

IO/M indicates whether the Read/Write is to memory or l/O Tristated during Hold
and Halt modes.

SID (Input)

Serial input data line The data on this line is loaded into accumulator bit 7
whenever a RIM instruction is executed.
SEC1312 MICROPROCESSOR AND MICROCONTROLLERBASED SYSTEMS
UNIT 1 PREPARED BY: DR. BETTY MARTIN

SOD (output)

Serial output data line. The output SOD is set or reset as specified by the SIM
instruction.

Vcc +5 volt supply.

Vss Ground Reference.

Signal Classification of 8085

The signal Classification of 8085 is as shown in fig3.

Fig: 3 Signal Classifications of 8085

SEC1312 MICROPROCESSOR AND MICROCONTROLLERBASED SYSTEMS
UNIT 1 PREPARED BY: DR. BETTY MARTIN

System Bus – wires connecting memory & I/O to microprocessor

– ADDRESS BUS

• Unidirectional

• Identifying peripheral or memory location

– DATA BUS

• Bidirectional

• Transferring data

– CONTROL BUS

• Synchronization signals

• Timing signals

• Control signal

ARCHITECTURE OF INTEL 8085 MICROPROCESSOR

SEC1312 MICROPROCESSOR AND MICROCONTROLLERBASED SYSTEMS
UNIT 1 PREPARED BY: DR. BETTY MARTIN

Fig:4 Architecture of intel 8085 microprocessor

The architecture of INTEL 8085 microprocessor is as shown in fig4.

Intel 8085 Microprocessor

Microprocessor consists of:

– Control unit: control microprocessor operations.

– ALU: performs data processing function.

– Registers: provide storage internal to CPU.

– Interrupts

– Internal data bus

SEC1312 MICROPROCESSOR AND MICROCONTROLLERBASED SYSTEMS
UNIT 1 PREPARED BY: DR. BETTY MARTIN

The ALU

• In addition to the arithmetic & logic circuits, the ALU includes the accumulator,
which is part of every arithmetic & logic operation.

• Also, the ALU includes a temporary register used for holding data temporarily
during the execution of the operation. This temporary register is not accessible by the
programmer.

Registers
General Purpose Registers

B, C, D, E, H & L (8 bit registers)

Can be used singly
Or can be used as 16 bit register pairs
BC, DE, HL

• H & L can be used as a data pointer (holds memory address)

• Special Purpose Registers

• Accumulator (8 bit register)

• Store 8 bit data

• Store the result of an operation

• Store 8 bit data during I/O transfer Address

Flag Register

– 8 bit register – shows the status of the microprocessor before/after an operation

– S (sign flag), Z (zero flag), AC (auxillary carry flag), P (parity flag) & CY (carry flag)

D7 D6 D5 D4 D3 D2 D1 D0

S Z X AC X P X CY
SEC1312 MICROPROCESSOR AND MICROCONTROLLERBASED SYSTEMS
UNIT 1 PREPARED BY: DR. BETTY MARTIN

Sign Flag

• Used for indicating the sign of the data in the accumulator

• The sign flag is set if negative (1 – negative)

• The sign flag is reset if positive (0 –positive)

Zero Flag

• Is set if result obtained after an operation is 0

• Is set following an increment or decrement operation of that register

Carry Flag

10110011

+ 01001101

---------------

00000000

– Is set if there is a carry or borrow from arithmetic operation

1011 0101 1011 0101

+ 0110 1100 - 1100 1100

--------------- ---------------

Carry 1 0010 0001 Borrow 1 1110 1001

Auxillary Carry Flag

– Is set if there is a carry out of bit 3

SEC1312 MICROPROCESSOR AND MICROCONTROLLERBASED SYSTEMS
UNIT 1 PREPARED BY: DR. BETTY MARTIN

Parity Flag

• Is set if parity is even

• Is cleared if parity is odd

The Internal Architecture

We have already discussed the general purpose registers, the

Accumulator, and the flags.

The Program Counter (PC)

– This is a register that is used to control the sequencing of the execution of

instructions.

– This register always holds the address of the next instruction.

– Since it holds an address, it must be 16 bits wide.

The Stack pointer

– The stack pointer is also a 16-bit register that is used to point into memory.

– The memory this register points to is a special area called the stack.

– The stack is an area of memory used to hold data that will be retreived
soon.

– The stack is usually accessed in a Last In First Out (LIFO) fashion.

Non Programmable Registers

Instruction Register & Decoder

– Instruction is stored in IR after fetched by processor

– Decoder decodes instruction in IR

Internal Clock generator

SEC1312 MICROPROCESSOR AND MICROCONTROLLERBASED SYSTEMS
UNIT 1 PREPARED BY: DR. BETTY MARTIN

– 3.125 MHz internally

– 6.25 MHz externally

The Address and Data Busses

•The address bus has 8 signal lines A8 – A15 which are unidirectional.

•The other 8 address bits are multiplexed (time shared) with the 8 data bits.

So, the bits AD0 – AD7 are bi-directional and serve as A0 – A7 and D0 – D7 at the
same time.

•During the execution of the instruction, these lines carry the address bits during the
early part, then during the late parts of the execution, they carry the 8 data bits.

In order to separate the address from the data, we can use a latch to save the value
before the function of the bits changes.

Demultiplexing AD7-AD0

– From the above description, it becomes obvious that the AD7– AD0 lines are serving
a dual purpose and that they need to be demultiplexed to get all the information.

– The high order bits of the address remain on the bus for three clock periods. However,
the low order bits remain for only one clock period and they would be lost if they are not
saved externally. Also, notice that the low order bits of the address disappear when they
are needed most.

– To make sure we have the entire address for the full three clock cycles, we will use an
external latch to save the value of AD7– AD0 when it is carrying the address bits. We
use the ALE signal to enable this latch.

Demultiplexing AD7-AD0

Given that ALE operates as a pulse during T1, we will be able to latch the
address. Then when ALE goes low, the address is saved and the AD7– AD0 lines can
be used for their purpose as the bi-directional data lines.
SEC1312 MICROPROCESSOR AND MICROCONTROLLERBASED SYSTEMS
UNIT 1 PREPARED BY: DR. BETTY MARTIN

Demultiplexing the Bus AD7 – AD0

• The high order address is placed on the address bus and hold for 3 clk periods,

• The low order address is lost after the first clk period, this address needs to be
hold however we need to use latch

• The address AD7 – AD0 is connected as inputs to the latch 74LS373.

• The ALE signal is connected to the enable (G) pin of the latch and the OC –
Output control – of the latch is grounded

ADDRESSING MODES

The microprocessor has different ways of specifying the data for the
instruction. These are called “addressing modes”.

The 8085 has four addressing modes:

– Implied CMA

– Immediate MVI B, 45

– Direct LDA 4000

– Indirect LDAX B

Load the accumulator with the contents of the memory location whose address is stored
in the register pair BC).

Many instructions require two operands for execution. For example transfer of
data between two registers. The method of identifying the operands position by the
instruction format is known as the addressing mode. When two operands are involved in
an instruction, the first operand is assumed to be in a register Mp itself.

Types of Addressing Modes

• Register addressing
• Direct addressing mode
SEC1312 MICROPROCESSOR AND MICROCONTROLLERBASED SYSTEMS
UNIT 1 PREPARED BY: DR. BETTY MARTIN

• Register indirect addressing

• Immediate Addressing mode
• Implied addressing mode

Register Addressing

This type of addressing mode specifies register or register pair that

contains data.ie (only the register need be specified as the address of the
operands).
Example MOV B, A (the content of A is copied into the register B)

Direct Addressing Mode

Data is directly copied from the given address to the register.

Example LDA 3000H (The content at the location 3000H is copied to the
register A).

Register Indirect Addressing

In this mode, the address of operand is specified by a register pair

Example MOV A, M (Move data from memory location specified by H-L pair to
accumulator)

Immediate Addressing Mode

In this mode, the operand is specified within the instruction itself.

Example MVI A, 05 H (Move 05 H in accumulator.)

Implied Addressing Mode

This mode doesn't require any operand. The data is specified by opcode itself.

Example RAL,

CMP
SEC1312 MICROPROCESSOR AND MICROCONTROLLERBASED SYSTEMS
UNIT 1 PREPARED BY: DR. BETTY MARTIN

INSTRUCTION SET OF 8085

An instruction is a binary pattern designed inside a microprocessor to perform a

specific function. The entire group of instructions that a microprocessor supports is
called Instruction Set. Since the 8085 is an 8-bit device it can have up to 28 (256)
instructions. However, the 8085 only uses 246 combinations that represent a total of 74
instructions. Each instruction has two parts. The first part is the task or operation to be
performed. This part is called the “opcode” (operation code). The second part is the
data to be operated on. This part is called the “operand”.

Instruction Size

• Depending on the operand type, the instruction may have different sizes. It will
occupy a different number of memory bytes.

– Typically, all instructions occupy one byte only.

– The exception is any instruction that contains immediate data or a memory address.

• Instructions that include immediate data use two bytes.

– One for the opcode and the other for the 8-bit data.

• Instructions that include a memory address occupy three bytes.

– One for the opcode, and the other two for the 16-bit address.

Classification of Instruction Set

• Data Transfer Instruction

• Arithmetic Instructions
• Logical Instructions
• Branching Instructions
• Machine Control Instructions
DATA TRANSFER INSTRUCTIONS

Opcode Operand Description

SEC1312 MICROPROCESSOR AND MICROCONTROLLERBASED SYSTEMS
UNIT 1 PREPARED BY: DR. BETTY MARTIN

MOV Rd, Rs Copy from source to

M, Rs destination.
Rd, M

This instruction copies the contents of the source register into the destination register.
The contents of the source register are not altered. If one of the operands is a memory
location, its location is specified by the contents of the HL registers. Example: MOV B, C
or MOV B, M.

Opcode Operand Description

MVI Rd, Data
M, Data Move immediate 8-bit

The 8-bit data is stored in the destination register or memory. If the operand is a
memory location, its location is specified by the contents of the H-L registers. Example:
MVI B, 57H or MVI M, 57H.

Opcode Operand Description

LDA 16-bit address Load Accumulator

The contents of a memory location, specified by a 16- bit address in the operand, are
copied to the accumulator. The contents of the source are not altered. Example: LDA
2034H

Opcode Operand Description

SEC1312 MICROPROCESSOR AND MICROCONTROLLERBASED SYSTEMS
UNIT 1 PREPARED BY: DR. BETTY MARTIN

LDAX B/D Register Pair Load accumulator indirect

The contents of the designated register pair point to a memory location. This instruction
copies the contents of that memory location into the accumulator. The contents of either
the register pair or the memory location are not altered. Example: LDAX B

Opcode Operand Description

STA 16-bit address Store accumulator direct

The contents of accumulator are copied into the memory location specified by the
operand. Example: STA 2500 H

Opcode Operand Description

STAX Reg. pair Store accumulator indirect

The contents of accumulator are copied into the memory location specified by the
contents of the register pair. Example: STAX B

Opcode Operand Description

SHLD 16-bit address Store H-L registers direct

SEC1312 MICROPROCESSOR AND MICROCONTROLLERBASED SYSTEMS
UNIT 1 PREPARED BY: DR. BETTY MARTIN

The contents of register L are stored into memory location specified by the 16-bit
address. The contents of register H are stored into the next memory location.
Example: SHLD 2550 H

Opcode Operand Description

XCHG None Exchange H-L with D-E

The contents of register H are exchanged with the contents of register D. The contents
of register L are exchanged with the contents of register E. Example: XCHG

Opcode Operand Description

SPHL None Copy H-L pair to the Stack

Pointer (SP)

This instruction loads the contents of H-L pair into SP. Example: SPHL

Opcode Operand Description

XTHL None Exchange H–L with top of

stack

The contents of L register are exchanged with the location pointed out by the contents
of the SP. The contents of H register are exchanged with the next location (SP + 1).
Example: XTHL

Opcode Operand Description

PCHL None Load program counter with

SEC1312 MICROPROCESSOR AND MICROCONTROLLERBASED SYSTEMS
UNIT 1 PREPARED BY: DR. BETTY MARTIN

H-L contents

The contents of registers H and L are copied into the program counter (PC). The
contents of H are placed as the high-order byte and the contents of L as the low-order
byte. Example: PCHL

Opcode Operand Description

PUSH Reg. pair Push register pair onto

stack

The contents of register pair are copied onto stack. SP is decremented and the
contents of high-order registers (B, D, H, A) are copied into stack. SP is again
decremented and the contents of low-order registers (C, E, L, Flags) are copied into
stack. Example: PUSH B

Opcode Operand Description

POP Reg. pair Pop stack to register pair

The contents of top of stack are copied into register pair. The contents of location
pointed out by SP are copied to the low-order register (C, E, L, Flags). SP is
incremented and the contents of location are copied to the high-order register (B, D, H,
A). Example: POP H

Opcode Operand Description

OUT 8-bit port address Copy data from

SEC1312 MICROPROCESSOR AND MICROCONTROLLERBASED SYSTEMS
UNIT 1 PREPARED BY: DR. BETTY MARTIN

accumulator to a port with

8- bit address

The contents of accumulator are copied into the I/O port. Example: OUT 78 H

Opcode Operand Description

IN 8-bit port address Copy data to accumulator

from a port with 8- bit
address

The contents of I/O port are copied into accumulator. Example: IN 8C H

1. ARITHMETIC INSTRUCTIONS

These instructions perform arithmetic operations such as addition, subtraction,

increment, and decrement.

Addition

Any 8-bit number, or the contents of register, or the contents of memory location can be
added to the contents of accumulator. The result (sum) is stored in the accumulator. No
two other 8-bit registers can be added directly. Example: The contents of register B
cannot be added directly to the contents of register C.

Opcode Operand Description

ADD R Add register or memory to

M accumulator
SEC1312 MICROPROCESSOR AND MICROCONTROLLERBASED SYSTEMS
UNIT 1 PREPARED BY: DR. BETTY MARTIN

The contents of register or memory are added to the contents of accumulator. The
result is stored in accumulator. If the operand is memory location, its address is
specified by H-L pair. All flags are modified to reflect the result of the addition. Example:
ADD B or ADD M

Opcode Operand Description

ADC R Add register or memory to

M accumulator with carry

The contents of register or memory and Carry Flag (CY) are added to the contents
of accumulator. The result is stored in accumulator. If the operand is memory location,
its address is specified by H-L pair. All flags are modified to reflect the result of the
addition. Example: ADC B or ADC M

Opcode Operand Description

ADI 8-bit data Add immediate to

accumulator

The 8-bit data is added to the contents of accumulator. The result is stored in
accumulator. All flags are modified to reflect the result of the addition. Example: ADI 45
H

Opcode Operand Description

ACI 8-bit data Add immediate to

accumulator with carry
SEC1312 MICROPROCESSOR AND MICROCONTROLLERBASED SYSTEMS
UNIT 1 PREPARED BY: DR. BETTY MARTIN

The 8-bit data and the Carry Flag (CY) are added to the contents of accumulator.
The result is stored in accumulator. All flags are modified to reflect the result of the
addition. Example: ACI 45 H

Opcode Operand Description

DAD Reg. pair Add register pair to H-L

pair

The 16-bit contents of the register pair are added to the contents of H-L pair. The result
is stored in H-L pair. If the result is larger than 16 bits, then CY is set.No other flags are
changed. Example: DAD B

Subtraction

Any 8-bit number, or the contents of register, or the contents of memory location can be
subtracted from the contents of accumulator.The result is stored in the
accumulator.Subtraction is performed in 2’s complement form. If the result is negative, it
is stored in 2’s complement form. No two other 8-bit registers can be subtracted directly.

Opcode Operand Description

SUB R Subtract register or

M memory from accumulator

The contents of the register or memory location are subtracted from the contents of the
accumulator. The result is stored in accumulator. If the operand is memory location, its
address is specified by H-L pair. All flags are modified to reflect the result of subtraction.
Example: SUB B or SUB M

Opcode Operand Description

SEC1312 MICROPROCESSOR AND MICROCONTROLLERBASED SYSTEMS
UNIT 1 PREPARED BY: DR. BETTY MARTIN

SBB R Subtract register or

M memory from accumulator
with borrow

The contents of the register or memory location and Borrow Flag (i.e. CY) are
subtracted from the contents of the accumulator. The result is stored in accumulator. If
the operand is memory location, its address is specified by H-L pair. All flags are
modified to reflect the result of subtraction. Example: SBB B or SBB M

Opcode Operand Description

SUI 8-bit data Subtract immediate from

accumulator

The 8-bit data is subtracted from the contents of the accumulator.The result is stored in
accumulator. All flags are modified to reflect the result of subtraction. Example: SUI 45
H

Opcode Operand Description

SBI 8-bit data Subtract immediate from

accumulator with borrow

The 8-bit data and the Borrow Flag (i.e. CY) is subtracted from the contents of the
accumulator. The result is stored in accumulator.All flags are modified to reflect the
result of subtraction. Example: SBI 45 H

Increment/Decrement
SEC1312 MICROPROCESSOR AND MICROCONTROLLERBASED SYSTEMS
UNIT 1 PREPARED BY: DR. BETTY MARTIN

The 8-bit contents of a register or a memory location can be incremented or

decremented by 1.The 16-bit contents of a register pair can be incremented or
decremented by 1. Increment or decrement can be performed on any register or a
memory location.

Opcode Operand Description

INR R Increment register or

M memory by 1

The contents of register or memory location are incremented by 1. The result is stored
in the same place. If the operand is a memory location, its address is specified by the
contents of H-L pair. Example: INR B or INR M

Opcode Operand Description

INX R Increment register pair by

1

The contents of register pair are incremented by 1. The result is stored in the same
place. Example: INX H

Opcode Operand Description

DCR R Decrement register or

M memory by 1

The contents of register or memory location are decremented by 1. The result is stored
in the same place. If the operand is a memory location, its address is specified by the
contents of H-L pair. Example: DCR B or DCR M
SEC1312 MICROPROCESSOR AND MICROCONTROLLERBASED SYSTEMS
UNIT 1 PREPARED BY: DR. BETTY MARTIN

Opcode Operand Description

DCX R Decrement register pair by

1

The contents of register pair are decremented by 1. The result is stored in the same
place. Example: DCX H

2. LOGICAL INSTRUCTIONS

These instructions perform logical operations on data stored in registers, memory and
status flags. The logical operations are:

• AND
• OR
• XOR
• Rotate
• Compare
• Complement

AND, OR, XOR

Any 8-bit data, or the contents of register, or memory location can logically have

• AND operation
• OR operation
• XOR operation

with the contents of accumulator. The result is stored in accumulator.

Opcode Operand Description

ANA R Logical AND register or

SEC1312 MICROPROCESSOR AND MICROCONTROLLERBASED SYSTEMS
UNIT 1 PREPARED BY: DR. BETTY MARTIN

M memory with accumulator

The contents of the accumulator are logically ANDed with the contents of register or
memory. The result is placed in the accumulator. If the operand is a memory location,
its address is specified by the contents of H-L pair. S, Z, P are modified to reflect the
result of the operation. CY is reset and AC is set. Example: ANA B or ANA M.

Opcode Operand Description

ANI 8-bit data Logical AND immediate

with accumulator

The contents of the accumulator are logically ANDed with the 8-bit data. The result is
placed in the accumulator. S, Z, P are modified to reflect the result.CY is reset, AC is
set. Example: ANI 86H.

Opcode Operand Description

ORA R Logical OR register or

M memory with accumulator

The contents of the accumulator are logically ORed with the contents of the register or
memory. The result is placed in the accumulator. If the operand is a memory location,
its address is specified by the contents of H-L pair.S, Z, P are modified to reflect the
result. CY and AC are reset. Example: ORA B or ORA M.

Opcode Operand Description

ORI 8-bit data Logical OR immediate with

SEC1312 MICROPROCESSOR AND MICROCONTROLLERBASED SYSTEMS
UNIT 1 PREPARED BY: DR. BETTY MARTIN

accumulator

The contents of the accumulator are logically ORed with the 8-bit data. The result is
placed in the accumulator. S, Z, P are modified to reflect the result.CY and AC are
reset. Example: ORI 86H.

Opcode Operand Description

XRA R Logical XOR register or

M memory with accumulator

The contents of the accumulator are XORed with the contents of the register or
memory. The result is placed in the accumulator. If the operand is a memory location,
its address is specified by the contents of H-L pair. S, Z, P are modified to reflect the
result of the operation. CY and AC are reset. Example: XRA B or XRA M.

Opcode Operand Description

XRI 8-bit data XOR immediate with

accumulator

The contents of the accumulator are XORedwith the 8-bit data. The result is placed in
the accumulator. S, Z, P are modified to reflect the result. CY and AC are reset.
Example: XRI 86H.

Rotate

Each bit in the accumulator can be shifted either left or right to the next position as
shown in fig5.

Opcode Operand Description

RLC None Rotate accumulator left

SEC1312 MICROPROCESSOR AND MICROCONTROLLERBASED SYSTEMS
UNIT 1 PREPARED BY: DR. BETTY MARTIN

Fig 5. : Work flow of RLC

Each binary bit of the accumulator is rotated left by one position. Bit D7 is placed in the
position of D0 as well as in the Carry flag. CY is modified according to bit D7. S, Z, P,
AC are not affected. Example: RLC.

Opcode Operand Description

RRC None Rotate accumulator right

Each binary bit of the accumulator is rotated right by one position. Bit D0 is placed in
the position of D7 as well as in the Carry flag. CY is modified according to bit D0. S, Z,
P, AC are not affected. Example: RRC.

Opcode Operand Description

RAL None Rotate accumulator left

through carry
SEC1312 MICROPROCESSOR AND MICROCONTROLLERBASED SYSTEMS
UNIT 1 PREPARED BY: DR. BETTY MARTIN

Fig 6. : Work flow of RAL

Each binary bit of the accumulator is rotated left by one position through the
Carry flag as shown in fig 6. Bit D7 is placed in the Carry flag, and the Carry flag is
placed in the least significant position D0. CY is modified according to bit D7. S, Z, P,
AC are not affected. Example: RAL.

Opcode Operand Description

RAR None Rotate accumulator right

through carry

Each binary bit of the accumulator is rotated right by one position through the Carry flag.
Bit D0 is placed in the Carry flag, and the Carry flag is placed in the most significant
position D7. CY is modified according to bit D0. S, Z, P, AC are not affected. Example:
RAR.

COMPARE

Any 8-bit data, or the contents of register, or memory location can be compares for:

• Equality
• Greater Than
• Less Than

with the contents of accumulator. The result is reflected in status flags.

SEC1312 MICROPROCESSOR AND MICROCONTROLLERBASED SYSTEMS
UNIT 1 PREPARED BY: DR. BETTY MARTIN

Opcode Operand Description

CMP R Compare register or

M memory with accumulator

The contents of the operand (register or memory) are compared with the contents of
the accumulator. Both contents are preserved .The result of the comparison is shown by
setting the flags of the PSW as follows:

• if (A) < (reg/mem): carry flag is set

• if (A) = (reg/mem): zero flag is set
• if (A) > (reg/mem): carry and zero flags are reset.

Example: CMP B or CMP M

Opcode Operand Description

CPI 8-bit data Compare immediate with

accumulator

The 8-bit data is compared with the contents of accumulator.The values being
compared remain unchanged. The result of the comparison is shown by setting the
flags of the PSW as follows:

• if (A) < data: carry flag is set

• if (A) = data: zero flag is set
• if (A) > data: carry and zero flags are reset

Example: CPI 89H

SEC1312 MICROPROCESSOR AND MICROCONTROLLERBASED SYSTEMS
UNIT 1 PREPARED BY: DR. BETTY MARTIN

COMPLEMENT

The contents of accumulator can be complemented. Each 0 is replaced by 1 and each

1 is replaced by 0.

Opcode Operand Description

CMA None Complement accumulator

The contents of the accumulator are complemented. No flags are affected. Example:
CMA.

Opcode Operand Description

CMC None Complement carry

The Carry flag is complemented. No other flags are affected. Example: CMC.

Opcode Operand Description

STC None Set carry

The Carry flag is set to 1. No other flags are affected. Example: STC.

3. BRANCHING INSTRUCTIONS

The branching instruction alters the normal sequential flow. These instructions alter
either unconditionally or conditionally.
Branch operations are of two types:
Unconditional branch-- Go to a new location no matter what.
Conditional branch-- Go to a new location if the condition is true.
SEC1312 MICROPROCESSOR AND MICROCONTROLLERBASED SYSTEMS
UNIT 1 PREPARED BY: DR. BETTY MARTIN

Opcode Operand Description

JMP 16-bit address Jump unconditionally

The program sequence is transferred to the memory location specified by the 16-bit
address given in the operand.
Example: JMP 2034 H.

Opcode Operand Description

Jx 16-bit address Jump conditionally

The program sequence is transferred to the memory location specified by the 16-bit
address given in the operand based on the specified flag of the PSW. Replace x with
condition
Example: JZ 2034 H.
Jump conditionally

Opcode Description Status flag

JC Jump if Carry CY = 1

JNC Jump if no carry CY=0

JP Jump if positive S=0
JM Jump if minus S=1
JZ Jump if Zero Z=1
JNZ Jump if no zero Z=0
JPE Jump if parity even P=1
JPO Jump if parity odd P=0
SEC1312 MICROPROCESSOR AND MICROCONTROLLERBASED SYSTEMS
UNIT 1 PREPARED BY: DR. BETTY MARTIN

Opcode Operand Description

CALL 16-bit address Call unconditionally

The program sequence is transferred to the memory location specified by the 16-bit
address given in the operand. Before the transfer, the address of the next instruction
after CALL (the contents of the program counter) is pushed onto the stack.
Example: CALL 2034 H.
Opcode Operand Description

Cx 16-bit address Call conditionally

The program sequence is transferred to the memory location specified by the 16-
bit address given in the operand based on the specified flag of the PSW. Before the
transfer, the address of the next instruction after the call (the contents of the program
counter) is pushed onto the stack. Replace x with condition
Example: CZ 2034 H.

Call Conditionally

Opcode Description Status flag

CC Call if carry CY=1
CNC Call if no carry CY=0
CP Call if positive S=0
CM Call if minus S=1
CZ Call if Zero Z=1
CNZ Call if no zero Z=0
CPE Call if parity even P=1
CPO Call if parity odd P=0
SEC1312 MICROPROCESSOR AND MICROCONTROLLERBASED SYSTEMS
UNIT 1 PREPARED BY: DR. BETTY MARTIN

Opcode Operand Description

RET None Return unconditionally

The program sequence is transferred from the subroutine to the calling program. The
two bytes from the top of the stack are copied into the program counter, and program
execution begins at the new address.
Example: RET.
Opcode Operand Description

Rx None Call conditionally

The program sequence is transferred from the subroutine to the calling program based
on the specified flag of the PSW. The two bytes from the top of the stack are copied
into the program counter, and program execution begins at the new address. Example:
RZ. Replace x with condition
RETURN CONDITIONALLY

Opcode Description Status flag

RC Return if carry CY=1
RNC Return if no carry CY=0
RP Return Call if positive S=0
RM Return if minus S=1
RZ Return if Zero Z=1
RNZ Return if no zero Z=0
RPE Return if parity even P=1
RPO Return if parity odd P=0
SEC1312 MICROPROCESSOR AND MICROCONTROLLERBASED SYSTEMS
UNIT 1 PREPARED BY: DR. BETTY MARTIN

Opcode Operand Description

RST 0-7 Restart (Software

Interrupts)

The RST instruction jumps the control to one of eight memory locations depending upon
the number. These are used as software instructions in a program to transfer program
execution to one of the eight locations. Example: RST 3.
RESTART Address table
Instructions Restart address
RST 0 0000 H
RST 1 0008 H
RST 2 0010 H
RST 3 0018 H
RST 4 0020 H
RST 5 0028 H
RST 6 0030 H
RST 7 0038 H

4. MACHINE CONTROL INSTRUCTIONS

The control instructions control the operation of microprocessor.

Opcode Operand Description

NOP None No operation

No operation is performed. The instruction is fetched and decoded but no operation is
executed. Usually used for delay or to replace instructions during debugging.
Example: NOP
SEC1312 MICROPROCESSOR AND MICROCONTROLLERBASED SYSTEMS
UNIT 1 PREPARED BY: DR. BETTY MARTIN

Opcode Operand Description

HLT None Halt

The CPU finishes executing the current instruction and halts any further execution. An
interrupt or reset is necessary to exit from the halt state. Example: HLT

Opcode Operand Description

DI None Disable interrupt

The interrupt enable flip-flop is reset and all the interrupts except the TRAP are
disabled.
No flags are affected.
Example: DI
Opcode Operand Description

EI None Enable interrupt

The interrupt enable flip-flop is set and all interrupts are enabled. No flags are affected.
This instruction is necessary to re-enable the interrupts (except TRAP).

Example: EI
Operand Description
Opcode

RIM None Read Interrupt Mask

This is a multipurpose instruction used to read the status of interrupts 7.5, 6.5, 5.5 and
read serial data input bit. The instruction loads eight bits in the accumulator with the
following interpretations.

Example: RIM
SEC1312 MICROPROCESSOR AND MICROCONTROLLERBASED SYSTEMS
UNIT 1 PREPARED BY: DR. BETTY MARTIN

RIM Instruction

Opcode Operand Description

SIM None Set Interrupt Mask

This is a multipurpose instruction and used to implement the 8085 interrupts 7.5, 6.5,
5.5, and serial data output. The instruction interprets the accumulator contents as
follows.
Example: SIM
SIM Instruction
SEC1312 MICROPROCESSOR AND MICROCONTROLLERBASED SYSTEMS
UNIT 1 PREPARED BY: DR. BETTY MARTIN

TIMING DIAGRAM

Timing diagram is the display of initiation of read/write and transfer of data operations
under the control of 3-status signals IO / M, S1, and S0. All actions in the
microprocessor are controlled by either leading or trailing edge of the clock.
,
Machine Cycle
It is the time required by the microprocessor to complete the operation of accessing the
memory devices or I/O devices. In machine cycle various operations like opcode fetch,
memory read, memory write, I/O read, I/O write are performed.
T-State

Each clock cycle is called as T-states.

Each machine cycle is composed of many clock cycles. Since, the data and
instructions, both are stored in the memory, the µP performs fetch operation to read the
instruction or data and then execute the instruction. The 3-status signals: IO / M, S1,
and S0 are generated at the beginning of each machine cycle. The unique combination
of these 3-status signals identify read or write operation and remain valid for the
duration of the cycle.
Table 1 Machine Cycle Status And Control Signals
SEC1312 MICROPROCESSOR AND MICROCONTROLLERBASED SYSTEMS
UNIT 1 PREPARED BY: DR. BETTY MARTIN

Table1 shows details of the unique combination of these status signals to identify
different machine cycles. Thus, time taken by any µP to execute one instruction is
calculated in terms of the clock period. The execution of instruction always requires
read and writes operations to transfer data to or from the µP and memory or I/O
devices. Each read/ write operation constitutes one machine cycle (MC1) as indicated in
Fig.7. Each machine cycle consists of many clock periods/ cycles, called T-states.

Fig.7 Machine cycle showing clock periods

Processor Cycle:

The functions of the microprocessor are divided into fetch and execute cycle of
any instruction of a program. The program is nothing but number of instructions stored
in the memory in sequence. In the normal process of operation, the microprocessor
fetches (receives or reads) and executes one instruction at a time in the sequence until
it executes the halt (HLT) instruction.

Instruction Cycle

An instruction cycle is defined as the time required to fetch and execute an

instruction. For executing any program, basically 2-steps are followed sequentially with
the help of clocks

• Fetch, and

• Execute.
SEC1312 MICROPROCESSOR AND MICROCONTROLLERBASED SYSTEMS
UNIT 1 PREPARED BY: DR. BETTY MARTIN

The time taken by the µP in performing the fetch and execute operations are
called fetch and execute cycle. Thus, sum of the fetch and execute cycle is called the
instruction cycle as indicated in Fig. 8. Each read or writes operation constitutes a
machine cycle. The instructions of 8085 require 1–5 machine cycles containing 3–6
states (clocks). The 1st machine cycle of any instruction is always an Op Code fetch
cycle in which the processor decides the nature of instruction. It is of at least 4-states. It
may go up to 6-states.

Fig.8 Processor cycle

Rules To Identify Number Of Machine Cycles In An Instruction:

• If an addressing mode is direct, immediate or implicit then No. of machine cycles =

No. of bytes.

• If the addressing mode is indirect then No. of machine cycles = No. of bytes + 1.
Add +1 to the No. of machine cycles if it is memory read/write operation.

• If the operand is 8-bit or 16-bit address then, No. of machine cycles = No. of bytes
+1.

• These rules are applicable to 80% of the instructions of 8085.

Timing Diagram of Opcode Fetch

The process of Opcode fetch operation requires minimum 4-clock cycles T1, T2,
T3, and T4 and is the 1st machine cycle (M1) of every instruction.

Example
SEC1312 MICROPROCESSOR AND MICROCONTROLLERBASED SYSTEMS
UNIT 1 PREPARED BY: DR. BETTY MARTIN

Fetch a byte 41H stored at memory location 2105H.

For fetching a byte, the microprocessor must find out the memory location where it is
stored. Then provide condition (control) for data flow from memory to the
microprocessor. The process of data flow and timing diagram of fetch operation are
shown in Fig. 9. The microprocessor fetches Opcode of the instruction from the memory
as per the sequence below

• A low IO/M means microprocessor wants to communicate with memory.

• The microprocessor sends a high on status signal S1 and S0 indicating fetch
operation.
• The microprocessor sends 16-bit address. AD bus has address in 1st clock of the
1st machine cycle, T1.
• AD7 to AD0 address is latched in the external latch when ALE = 1.
• AD bus now can carry data.
• In T2, the RD control signal becomes low to enable the memory for read
operation.
• The memory places opcode on the AD bus
• The data is placed in the data register (DR) and then it is transferred to IR.
• During T3 the RD signal becomes high and memory is disabled.
• During T4 the opcode is sent for decoding and decoded in T4.
• The execution is also completed in T4 if the instruction is single byte.
• More machine cycles are essential for 2- or 3-byte instructions. The 1st machine
cycle M1 is meant for fetching the opcode. The machine cycles M2 and M3 are
required either read/ write data or address from the memory or I/O devices.
SEC1312 MICROPROCESSOR AND MICROCONTROLLERBASED SYSTEMS
UNIT 1 PREPARED BY: DR. BETTY MARTIN

Fig. 9 Opcode fetch

Example For Opcode Fetch

• Explain the execution of MVI B, 05H stored at locations indicated below

Fig. 10 Timing diagram for MVI B,05H

SEC1312 MICROPROCESSOR AND MICROCONTROLLERBASED SYSTEMS
UNIT 1 PREPARED BY: DR. BETTY MARTIN

The MVI B, 05H instruction requires 2-machine cycles (M1 and M2). M1 requires
4-states and M2 requires 3-states, total of 7-states as shown in Fig. 10. Status signals
IO/M, S1 and S0 specifies the 1st machine cycle as the op-code fetch. In T1-state, the
high order address {10H} is placed on the bus A15 ⇔ A8 and low-order address {00H}
on the bus AD7 ⇔ AD0 and ALE = 1. In T2 -state, the RD line goes low and the data 06
H from memory location 1000H are placed on the data bus. The fetch cycle becomes
complete in T3-state. The instruction is decoded in the T4-state. During T4-state, the
contents of the bus are unknown. With the change in the status signal, IO/M = 0, S1 = 1
and S0 = 0, the 2nd machine cycle is identified as the memory read. The address is
1001H and the data byte [05H] is fetched via the data bus. Both M1 and M2 perform
memory read operation, but the M1 is called op-code fetch i.e., the 1st machine cycle of
each instruction is identified as the opcode fetch cycle.

TIMING DIAGRAM OF MEMORY READ

Operation:

• It is used to fetch one byte from the memory.

• It requires 3 T-States.
• It can be used to fetch operand or data from the memory.
• During T1, A8-A15 contains higher byte of address. At the same time ALE is high.
Therefore Lower byte of address A0-A7 is selected from AD0-AD7 as shown in
fig 11.
• Since it is memory ready operation, IO/M (bar) goes low.
• During T2 ALE goes low, RD (bar) goes low. Address is removed from AD0-AD7
and data D0-D7 appears on AD0-AD7.
• During T3, Data remains on AD0-AD7 till RD (bar) is at low signal.
SEC1312 MICROPROCESSOR AND MICROCONTROLLERBASED SYSTEMS
UNIT 1 PREPARED BY: DR. BETTY MARTIN

Fig 11.Memory read timing diagram

TIMING DIAGRAM OF MEMORY WRITE

Operation:

• It is used to send one byte into memory.

• It requires 3 T-States.
• During T1, ALE is high and contains lower address A0-A7 from AD0-AD7.
• A8-A15 contains higher byte of address.
• As it is memory operation, IO/M (bar) goes low.
• During T2, ALE goes low, WR (bar) goes low and Address is removed from AD0-
AD7 and then data appears on AD0-AD7 as in fig 12.
• Data remains on AD0-AD7 till WR (bar) is low.
SEC1312 MICROPROCESSOR AND MICROCONTROLLERBASED SYSTEMS
UNIT 1 PREPARED BY: DR. BETTY MARTIN

Fig 12.Memory Write timing diagram

TIMING DIAGRAM OF IO READ

Operation:

• It is used to fetch one byte from an IO port.

• It requires 3 T-States.
• During T1, The Lower Byte of IO address is duplicated into higher order address
bus A8-A15 as in fig13.
• ALE is high and AD0-AD7 contains address of IO device.
• IO/M (bar) goes high as it is an IO operation.
• During T2, ALE goes low, RD (bar) goes low and data appears on AD0-AD7 as
input from IO device.
• During T3 Data remains on AD0-AD7 till RD (bar) is low.
SEC1312 MICROPROCESSOR AND MICROCONTROLLERBASED SYSTEMS
UNIT 1 PREPARED BY: DR. BETTY MARTIN

Fig 13.IO Read timing diagram

TIMING DIAGRAM OF IO WRITE

Operation:

• It is used to writ one byte into IO device.

• It requires 3 T-States.
• During T1, the lower byte of address is duplicated into higher order address bus
A8-A15 as in fig 14.
• ALE is high and A0-A7 address is selected from AD0-AD7.
• As it is an IO operation IO/M (bar) goes low.
• During T2, ALE goes low, WR (bar) goes low and data appears on AD0-AD7 to
write data into IO device.
• During T3, Data remains on AD0-AD7 till WR(bar) is low.
SEC1312 MICROPROCESSOR AND MICROCONTROLLERBASED SYSTEMS
UNIT 1 PREPARED BY: DR. BETTY MARTIN

Fig 14. IO Write timing diagram