Scribd
Upload
51 views5 pages

Solid State AC Relays Using Triacs

Solid state relay (SSR) consists of four main parts: 1. An opto-isolator or opto-coupler to isolate the low voltage DC control, often from a microcomputer, from the high voltage AC. The output is often a photo transistor or photo diac for switching on a triac. Snubber circuit(s) to prevent false firing of the triac from noise spikes generated with magnetic loads.

Uploaded by

Anthony B. Sabaysabay Jr.
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
51 views5 pages

Solid State AC Relays Using Triacs

Solid state relay (SSR) consists of four main parts: 1. An opto-isolator or opto-coupler to isolate the low voltage DC control, often from a microcomputer, from the high voltage AC. The output is often a photo transistor or photo diac for switching on a triac. Snubber circuit(s) to prevent false firing of the triac from noise spikes generated with magnetic loads.

Uploaded by

Anthony B. Sabaysabay Jr.
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 5

About me Bristol VA/TN E-Mail Hobby Electronics Environmentalism US Constitution Ending Racism Religious Themes PICAXE Microcontroller Arduino

Arduino Microcontroller Microcontroller Input/Output Ports

The most basic solid state relay.

Solid State AC Relays Using Triacs


The most basic solid state relay (SSR) is shown above being a light source and a triac with a photosensitive gate. For more information on how triacs and SCRs operate see Basic Triac and SCR Projects and Circuits. A solid state relay (SSR) consists of four main parts: 1. An opto-isolator or opto-coupler to isolate the low voltage DC control, often from a microcomputer, from the high voltage AC. The input opto-coupler is often a light emitting diodes while the output is often a photo transistor or photo diac for switching on a triac. 2. The SSR often has an internal zero-crossing detector circuit to switch on the triac during the time the sin wave is a little past zero or 180 degrees. This helps prevent damage the load and needless power surges. 3. A triac acting as an AC switch. If the SSR is for DC the output is a power transistor. 4. A snubber circuit(s) to prevent false firing of the triac from noise spikes generated with magnetic loads.

A more practical SSR. Also see Using Opto-Couplers An important note is the output has no electrical connection to the input and can

provide up to several thousand volts isolation. Also see More sample circuits.

Opto-Isolators with Diacs


An opto-isolator is a solid state device designed to provide electrical isolation between input and output. The input consists of a light emitting diode (LED) in a six or eight pin dip (IC) package depending on type. The output can be a photo transistor, photo diac, etc. There is no electrical contact between input and output. When the LED is turned on, the diac, transistor, etc. will conduct from the light emitted from the diode thus turning on the triac like a switch. The MOC3011 series is made to connect to triacs, the MOC301x types for 110 volts, and the MOC302x types for 240 volts. View the schematic.

(above) MOC3042 Other opto-couplers have have a built in zero-crossing detector.

Snubbers
A snubber circuit (usually of the RC type) is often used between MT1 and MT2. Snubber circuits are used to prevent premature triggering caused for example by voltage spikes in the AC supply or those produced by inductive loads such as motors. Also, a gate resistor or capacitor (or both in parallel) may be connected between gate and MT1 to further prevent false triggering. That could increase the required trigger current and perhaps a delay in turnoff as the capacitor discharges. In this circuit above the "hot" side of the line is switched and the load connected to the cold or ground side. The 39-ohm resistor and 0.01F capacitor are for snubbing of the triac, and the 470 ohm resistor and 0.05 F capacitor are for snubbing the coupler. These components may or may not be necessary depending upon the particular and load used. For more on the above opto-coupler see moc30xx series opto-isolator and MOC3042 with zero-crossing circuits. (both pdf files)

View the schematic.

Added July 31, 2011


Using Hall Effect Switches Using Ratiometric Hall Effect Sensors Using Hall Effect Sensors with the Arduino-ATMEGA168 Connecting the Arduino to the TMP37 Centigrade Temperature Sensor How to connect batteries in Series/Parallel 12AV6 Vacuum Tube AM Radio Coils for Highly Selective Crystal Radio Adding a Push-Pull Output Stage to a LM386 Audio Amplifier Read this safety warning and Disclaimer Tutorial: Transistor-Zener Diode Regulator Circuits Tricks and Tips for the LM78XX Series Voltage Regulators Bi-Polar Power Supplies Build a Thermocouple Amplifier Build a Potato battery

Build an Adjustable 0-34 volt power supply with the LM317 Testing a Diac Basic Triacs and SCRs Solid State AC Relays with Triacs Light Activated Silicon Controlled Rectifier (LASCR) Basic Transistor Driver Circuits for Micro-Controllers Opto-Isolated Transistor Drivers for Micro-Controllers Build a H-Bridge Motor Control with Power MOSFETS Using a CdS Photocells Voltage Comparator Information And Circuits Resistive Humidity Sensors Reed Switches Basic Power Transformers Power Supply Rectification Diodes and Rectifiers

You Tube Videos


Power Supplies Part 1 Power Supplies Part 2 Power Supplies Part 3 Using a Load Lamp Using and Testing Hall Effect Sensors

Web site Copyright Lewis Loflin, All rights reserved. If using this material on another site, please provide a link back to my site.

You might also like