Scribd
Upload
31 views2 pages

Design RCC-Slab

The document outlines the slab design according to IS 456:2000, detailing the materials, loads, and reinforcement specifications. It includes calculations for flexure, shear, and deflection to ensure structural safety and compliance. The design incorporates specific dimensions, load factors, and reinforcement ratios for effective performance.

Uploaded by

lau
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
31 views2 pages

Design RCC-Slab

The document outlines the slab design according to IS 456:2000, detailing the materials, loads, and reinforcement specifications. It includes calculations for flexure, shear, and deflection to ensure structural safety and compliance. The design incorporates specific dimensions, load factors, and reinforcement ratios for effective performance.

Uploaded by

lau
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

SLAB DESIGN (as per Limit State Design of IS 456:2000)

[A] DESIGN INPUT:


Y
(a) Materials: Discontinuous edge

4.00 m
Slab thk. (D) = 130 mm

Discontinuous edge
Continuous edge
Floor finish thk. (ff) = 75 mm
Concrete cover (cc) = 15 mm

Short span (lx)


Main bar dia. (Dmain) = 10 mm
Distn. bar dia. (Dsec) = 8 mm
Limiting basic 'span/ eff. depth' value = 23
X
Concrete grade (fcu) = 25 MPa Continuous edge
Reinf't. type: HYSD Bars Long span (ly) 5.00 m
Reinf't. grade (fy) = 500 MPa
Slab dimensions/ Edge conditions
(b) Loads:
[i] Dead Load (DL):
Self weight of slab = 25 x D = 3.25 kN/sq.m
Floor finish load = 20 x ff = 1.5 kN/sq.m
Ceiling load @ 0.5 kN/sq.m
Services @ 0.5 kN/sq.m
Other loads (if any) @ 0.25 kN/sq.m
i.e. Total DL = 6 kN/sq.m

[ii] Live Load (LL):


Live Load @ 3 kN/sq.m
Other loads (if any) @ 0.5 kN/sq.m
i.e. Total LL = 3.5 kN/sq.m

[iii] Factored Load (w):


Total factored load, w = 1.5 x DL + 1.5 x LL = 14.25 kN/sq.m

[B] FLEXURE:
Aspect ratio = ly/lx = 1.25
Effective depth, d1 = D - cc - 0.5 x Dmain = 110 mm
Effective depth, d2 = D - cc - Dmain - 0.5 Dsec = 101 mm
(a) Short span moments:
Mx (-ve) = 0.063 x w x lx^2 = 14.37 kNm/m => M/ (b x d1^2) = 1.19 => pt = 0.29%
Mx (+ve) = 0.047 x w x lx^2 = 10.72 kNm/m => M/ (b x d1^2) = 0.89 => pt = 0.22%
(b) Long span moments:
My (-ve) = 0.047 x w x lx^2 = 10.72 kNm/m => M/ (b x d2^2) = 1.06 => pt = 0.26%
My (+ve) = 0.036 x w x lx^2 = 8.21 kNm/m => M/ (b x d2^2) = 0.81 => pt = 0.2%

Element:
Client:

Project: Doc. No.: Location/ Grids:


Rev. Ppd. by Date Chd. by Date
Project: 2 Designation:
Structure: 1
Type: 0 . Sht. 1 of 2

FORM NO : ECE-E0001
SLAB REINFORCEMENT:
Limiting values:
Distn. steel in each dirn @ 0.12% = 156 sq.mm/ m
Max. spg. of main bars = Min (3d, 300 mm) = 300 mm
Max. spg. of distn. bars = Min (5d, 450 mm) = 450 mm
Edge strips (Distn. steel):
Steel in edge strips @ Lx (2 nos. 0.6m wide) & @ Ly (2 nos. 0.5m wide):
Provide T8 @ 300 c/c (T&B)

Steel @ short span:


Middle strip 3.75m wide:
Top steel = 318.8 sq.mm/ m
Spacing of top bars = 246.3 mm
Provide T10 @ 200 mm c/c => Steel ratio (As,prov/ As,reqd) = 1.23
Bottom steel = 234 sq.mm/ m
Spacing of bottom bars = 246.3 mm
Provide T10 @ 200 mm c/c => Steel ratio (As,prov/ As,reqd) = 1.67

Steel @ long span:


Middle strip 3m wide:
Top steel = 257.1 sq.mm/ m
Spacing of top bars = 305.5 mm
Provide T10 @ 200 mm c/c => Steel ratio (As,prov/ As,reqd) = 1.52
Bottom steel = 194.4 sq.mm/ m
Spacing of bottom bars = 404.1 mm
Provide T10 @ 200 mm c/c => Steel ratio (As,prov/ As,reqd) = 2.02

[C] SHEAR:
Shear force, V = 0.45 x w x lx = 25.65 kN/m
Nominal shear stress, vu = V / (b x d1) = 0.24 MPa
(Note: b = slab width = 1000 mm in above equation)
Slab reinforcement actually provided, pt,act = 0.17%
Maximum shear stress, Tc,max (Table 20) = 3.1 MPa
Design shear strength of concrete, vc (Table 19) = 0.3 MPa
Modification factor for shear strength of slab, k (Table:Clause 40.2.1.1) = 1.29
Modified shear strength of slab, k x vc (Clause 40.2.1.1) = 0.4
Since vu < k.vc, slab is safe in shear (OK)

[D] DEFLECTION:
fs = 0.58 x fy x (As,req/ As,prov) = 300 MPa
MF (Tension reinf't), MFt = 1.91; MF (Compr. reinf't), MFc = 1
Span/ (d1 x MFt x MFc) = 19.2 <= 23 (OK)

Element:
Client:

Project: Doc. No.: Location/ Grids:


Rev. Ppd. by Date Chd. by Date
Project: 2 Designation:
Structure: 1
Type: 0 . Sht. 2 of 2

FORM NO : ECE-E0001

You might also like