Scribd
Upload
12 views2 pages

Inb Test en

This quick start guide provides essential information for operating electrical installations testers, including setup, operation, and safety precautions. Users are instructed to connect test leads, select appropriate ranges, and ensure safety by not exceeding maximum input values. The guide emphasizes the importance of inspecting the device before use and following specific procedures to avoid electric shock and damage.

Uploaded by

Paulito Paulinito
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
12 views2 pages

Inb Test en

This quick start guide provides essential information for operating electrical installations testers, including setup, operation, and safety precautions. Users are instructed to connect test leads, select appropriate ranges, and ensure safety by not exceeding maximum input values. The guide emphasizes the importance of inspecting the device before use and following specific procedures to avoid electric shock and damage.

Uploaded by

Paulito Paulinito
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Electrical Installations Testers Quick Start Guide

1. Introduction
Dear Customer! Thank you for your purchase in TME! To protect the environment we have prepared for
you this quick start guide. Before operating the unit, please read it carefully. Please visit www.tme.eu
Illustrations in this manual are only example images and may differ from the actual item. It does
not change their main characteristics.

2. Application
The device is designed for electrical installations testing.

3. Unit setup and operation

T - Test button
L - Display
S - Test probes
Z - Range selector
y Connect the test leads and/or power supply cables to the respective terminals of the meter if they
are required.
y Set the function/range selector switch to the desired position, if possible. If the value of the
measured signal is unknown, select the highest range.
y Touch the test probes to the measuring point, connect measurement clamp, press the appropriate
button or put your device to perform the measurement.
y Watch the input signal value.
y Overrange is indicated by the corresponding symbol displayed on the LCD.
When you see this symbol remove the cause of the overrange. Select a higher range, or if
the highest range is already selected immediately stop the measurement. During resistance
measurement overrange means open circuit or too high resistance.
y To replace the battery open the battery cover by unscrewing the screws or loosening the latch,
replace the battery, close the cover.

4. Precautions

1/2
y Never exceed maximum input values for all functions.
y Do not apply voltage higher than the rated voltage, specified and marked on the unit between
terminals or between the terminal and the earth.
y Use appropriate terminals, functions, and ranges for selected measurement.
y Do not attempt current measurement if current value exceeds the current rating of the fuse.
y Before changing the measurement function, disconnect the test leads from the measurement
circuit.
y Before measuring resistance, continuity, diodes or capacitance turn off the power and discharge
all high-voltage capacitors.
y Do not use the device if it is damaged. Before using the device, inspect the housing. Check if it
has no cracks or broken off pieces. Carefully check the insulation surrounding the connectors.
y Make sure the battery cover is closed and latched before operating the unit.
y Do not use the device if it works incorrectly. Protection may be impaired. If you are unsure
whether the device is working correctly, take it to the service.
y When you make the electrical connections, first connect the black test lead before connecting the
red test lead, when disconnecting first disconnect the red test lead and then black test lead.
y Use caution when working with voltages above 30 V AC rms, 42 V AC peak and 60 V DC. These
voltages can cause electric shock.
y Before starting the measurements check if insulation of test leads and probes is not damaged and
there is no exposed metal.
y Damaged test leads should be replaced by new one.
y During measurement, always keep your fingers on the probes behind the hand guards.
y Before opening the battery compartment cover remove the test leads from the device, if it is
possible.
y Replace the battery with a new one or charge the battery if the display shows the battery low
indicator.
y When servicing the unit, use only spare parts specified by the manufacturer.
y Never use the device in explosive environments, if it is not designed to work in such conditions.
y Do not allow the device to get wet - may damage the device.

2/2

You might also like